Zanussi Refrigerator ZU 9154 User Manual

REFRIGERATOR  
ZU 9154  
INSTRUCTION BOOKLET  
2222682-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
These warnings are provided in the interests of your safety. Ensure that you understand them all  
before installing or using this appliance. Your safety is of paramount importance. If you are unsure  
about any of the meanings of these warnings contact the Customer Care Department.  
Prior to Installation  
General Safety  
Check the appliance for transport damage. Under  
no circumstance should a damaged appliance be  
installed. In the event of damage please contact  
your retailer.  
This appliance contains hydrocarbons in its  
cooling unit; maintenance and recharging  
must therefore only be carried out by autho-  
rized technicians.  
Take utmost care when handling your appli-  
ance so as not to cause any damages to the  
cooling unit with consequent possible fluid  
leakages.  
Installation  
This appliance is heavy. Care should be taken  
when moving it.  
The appliance must not be located close to  
It is dangerous to alter the specifications or  
radiators or boilers.  
attempt to modify this product in any way.  
Avoid prolonged exposure of the appliance to  
Ensure that the appliance does not stand on the  
electrical supply cable.  
direct sunlight.  
Do not use other electrical appliances (such  
as ice cream makers) inside of refrigerating  
appliances.  
Important: if the supply cable is damaged, it  
must be replaced by a cable available from the  
manufacturer or your local Service Force Centre.  
Any electrical work required to install this appli-  
ance should be carried out by a qualified electri-  
cian or competent person.  
During Use  
This appliance is designed for domestic use only,  
specifically for the storage of edible foodstuffs  
only. It is not intended for commercial or industrial  
use.  
Parts which heat up should not be exposed.  
Whenever possible, the back of the appliance  
should be close to a wall, but leaving the required  
distance for ventilation, as stated in the installa-  
tion instructions.  
Containers with flammable gases or liquids can  
leak at low temperatures. Do not store any con-  
tainers with flammable materials, such as spray  
cans, fire extinguisher refill cartridges etc. in the  
freezer.  
The appliance should be left for 2 hours after  
installation before it is turned on, in order to allow  
the refrigerant to settle.  
Frozen food should not be refrozen once it has  
Refrigerant  
thawed out.  
The refrigerant isobutane (R600a) is contained  
within the refrigerant circuit of the appliance, a  
natural gas with a high level of environmental  
compatibly, which is nevertheless flammable.  
Do not place carbonated or fizzy drinks in the  
freezer compartment.  
Ice lollies can cause ‘frost/freezer burns’ if con-  
sumed straight from the freezer.  
During transportation and installation of the appli-  
ance, be certain that none of the components of  
the refrigerant circuit become damaged.  
Do not remove items from the freezer compart-  
ment if your hands are damp/wet, as this could  
cause skin abrasions or frost/freezer burns.  
If the refrigerant circuit should become damaged:  
- avoid open flames and sources of ignition.  
- thoroughly ventilate the room in which the appli-  
ance is situated.  
Bottles and cans must not be placed in the freez-  
er as they can burst when the contents freeze.  
Manufacturers’ recommended storage times  
should be adhered to. Refer to relevant instruc-  
tions.  
Child Safety  
Do not allow children to tamper with the controls  
or play with the product.  
Maintenance and Cleaning  
Before cleaning, always switch off the appliance  
There is a risk of suffocation! Keep packaging  
material away from children!  
and disconnect from the electrical supply.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
When unplugging always pull the plug from the  
At the end of the Appliance Life  
When disposing of your appliance use an autho-  
mains socket, do not pull on the cable.  
rised disposal site.  
Servicing  
This product should be serviced by an authorised  
engineer and only genuine spare parts should be  
used.  
Remove the plug and ensure that any locks or  
catches are removed, to prevent young children  
being trapped inside.  
Under no circumstances should you attempt to  
repair the appliance yourself. Repairs carrier out  
by inexperienced persons may cause injury or  
serious malfunctioning. Contact your local  
Service Force Centre.  
DESCRIPTION OF THE APPLIANCE  
Dairy compartment  
Movable shelf  
Bottle storage shelf  
Salad bin  
Storage shelves  
Thermostat control  
OPERATION  
Before use  
Remove all securing tapes. Wash inside the appli-  
ance with lukewarm water and bicarbonate of soda  
(5 ml to 0.5 litre of water). Do not use soap or deter-  
gent as the smell may linger. Dry thoroughly.  
An intermediate position is usually the most suitable,  
although the temperature will be affected by:  
l
Room temperature  
l How often the door is opened  
l How much food is stored  
l Position of the appliance  
Setting the temperature  
The temperature inside the refrigerator is regulated  
by a thermostat with 6 temperature positions and  
one «OFF» (O) position.  
Position 1 = minimum coldness  
Position 6 = maximum coldness  
In determining the correct temperature control set-  
ting all these factors have to be considered and  
some experimentation may be necessary.  
When altering the temperature setting, allow 24  
hours for the temperature to stablise before making  
further changes.  
Turn the thermostat dial to the required position.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important  
Normal Operating Sounds  
During prologed periods of abnormally hot  
weather, if the thermostat is seto on too high a  
number, the cooling system may operate con-  
tinuously and the fridge coolilng plate may not  
defrost. Turning the knob to a lower number will  
cause the automatic defrosting to resume.  
If you wish to return to a lower temperature,  
turn the thermostat knob to a higher number,  
however you should turn the setting lower  
occasionally to allow automatic defrosting.  
You may hear faint gurgling or bubbling sounds  
when the refrigerant is pumped through the coils  
below, to the cooling evaporator.  
When the compressor is on, the refrigerant is  
being pumped round, and you will hear a whirring  
sound or pulsating noise from the compressor. A  
thermostat controls the compressor, and you will  
hear a faint ‘click’ when the thermostat cuts in and  
out.  
Fresh food refrigeration  
To obtain the best performance, do not store warm  
food or evaporating liquids in the refrigerator; do  
cover or wrap the food, particularly if it has a strong  
flavour.  
Do not cover the shelves with any protective material,  
such as paper, cardboard or plastic, which may  
obstruct the air circulation through them.  
To help you use your refrigerator correctly, here are  
some more useful hints:  
Raw meat (beef, pork, lamb & poultry): wrap in poly-  
thene bags and place on top of the salad drawers.  
Meat can only be stored safely in this way for one  
or two days at the most.  
Fruit & vegetables: these should be thoroughly  
cleaned and placed in the bottom salad drawers.  
Butter & cheese: these should be placed in special  
airtight containers or wrapped in aluminium foil or  
polythene bags to exclude as much air as possible.  
Milk bottles: these should have a cap and should be  
stored in the bottle rack on the door.  
The walls of the refrigerator are equipped with run-  
ners so that shelves can be positioned as desired.  
For better use of space, the front half-shelves can lie  
over the rear ones (see fig.).  
D338  
The door shelves  
Depending on the use of the bottle shelf (3) the short  
shelf (2) can be adjusted in the direction of the arrow  
(a).  
For more thorough cleaning, shelves can be removed,  
then refitted in their position. To make these adjuste-  
ments proceed as follows:  
1
4
top shelf (1): gradually pull in the direction of the  
arrows until it comes free;  
middle shelf (2): turn it in the direction of the arrows  
until it comes free from the metallic crosspiece (4);  
bottle shelf (3): push on the buttons (b) until it comes  
free, then pull it in the direction of the arrow.  
2
a
b
3
S.I.010  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
HEALTH AND SAFETY GUIDELINES  
Because of consumer demand, preservatives have been removed from many pre-prepared foods. This  
together with the changes in shopping habits to a once-a-week shop, mean that safe handling and  
storage of food is even more important than ever.  
The following tips should help you to ensure that  
the food in your home is in as perfect condition  
as possible.  
Keep the time between buying chilled food and  
placing it in your fridge as short as possible. Tests  
showed that the temperature of 1 litre of orange  
juice rose to 22°C in an hour between the super-  
market and home. It then took 11 hours to get  
down to 7°C in the refrigerator.  
Never allow spillages to dry and harden.  
Store eggs in the egg rack provided in the refrig-  
erator door. Discard any broken or chipped eggs.  
Regularly check the refrigerator door seal to  
ensure that it is clean and free from debris.  
Keep the refrigerator door closed as much as pos-  
sible.  
Always wash your hands with soapy water and  
dry them with a clean towel before handling food.  
Do not push food together too much, try to allow  
air to circulate around each item.  
Keep work surfaces clean and avoid cross conta-  
mination by not using the same work surface or  
knife, without washing them thoroughly in  
between.  
Cool cooked food as quickly as possible but do  
NOT place in the refrigerator until cool. (Leave  
food in a cool place in order that it can then be  
placed in the refrigerator as soon as possible).  
Do NOT mix raw and cooked meat, they must be  
in separate containers. Take care not to let the  
meat juices drip onto other food. If the meat does  
drip, remove everything and clean thoroughly.  
Do not store food uncovered.  
Remove suspect food from your refrigerator and  
clean (Refer to “Maintenance and Cleaning”).  
DEFROSTING  
The refrigerator automatically defrosts every time the  
compressor stops. The water is discharged, via the  
pipe, into a tray located at the back of the appliance  
above the compressor, where it evaporates.  
Important  
To avoid defrost water overflowing and dripping  
onto the food in the fridge, periodically clean  
the water discharge hole (F) situated under the  
salad drawers. Use the special cleaner provid-  
ed (P) which you will find already inserted into  
the discharge hole  
P
F
S.I.011  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE AND CLEANING  
Before any maintenance or cleaning work is carried  
out, DISCONNECT the appliance from the ELEC-  
TRICITY supply.  
1. Unscrew the light cover and then pull it outward  
by pressing as shown in the figure. Unscrew the  
bulb and replace it with a new 15 watt bulb (avail-  
able from your nearest Zanussi Service Force  
centre).  
Warning  
This appliance contains hydrocarbons in its  
cooling unit maintenance and recharging must  
therefore only be carried out by authorised  
technicians.  
Internal cleaning  
Clean the inside and accessories with warm water  
and bicarbonate of soda (5ml to 0.5 litre of water).  
Rinse and dry thoroughly.  
D411  
NEVER USE DETERGENTS, ABRASIVE POW-  
DERS, HIGHLY PERFUMED CLEANING PROD-  
UCTS OR WAX POLISHES, TO CLEAN THE INTE-  
RIOR AS THESE WILL DAMAGE THE SURFACE  
AND LEAVE A STRONG SMELL.  
2. Replace the light cover by sliding it into its original  
position and replacing the screw.  
Clean the drain hole of the water trough at regular  
intervals and make sure that the drain hole is never  
obstructed, so that the defrost water may flow freely.  
When the appliance is not in use  
When the appliance is not in use for long periods,  
disconnect from the electricity supply, empty all  
foods and clean the appliance, leaving the door ajar  
to prevent unpleasant smells.  
Important  
Do not use abrasive products.  
Periodic cleaning  
The appliance is equipped with a ventilation grid.  
Keep clean to guarantee good ventilation and good  
working order of the appliance.  
An accumulation of dust will affect the performance  
of the appliance and cause excessive electricity con-  
sumption.  
The structure of the appliance permits to clean the  
rear zone close to the wall, using a vacuum cleaner.  
1. Remove the plinth (1), then the ventilation grid (2);  
2. Carefully pull the air deflector out (3), checking  
that there is no water left from the defrosting.  
3
2
1
Changing the light bulb  
Should the interior light fail to work, first switch off  
the appliance and disconnect from the electricity  
supply, then replace the bulb as follows:  
S.I.013  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SOMETHING NOT WORKING?  
Before contacting your local Service Force Centre check the following points.  
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or  
installation, a charge will be made even if the appliance is under guarantee.  
Symptom  
Solution  
No power to appliance  
- Check there is power at the socket.  
- Check there is not a power cut by checking the  
household lights.  
- Check the fuse has not blown.  
The light does not come on  
- Ensure that the bulb is correctly fitted.  
- Replace the bulb if it has blown.  
- Check the door light switch is not jammed.  
The temperature in the fridge or freezer section is too  
high  
- Check the ambient temperature is within the appliances  
operating limits of 10˚C to 32˚C.  
- Check the thermostat knob is turned to the correct  
setting relative to ambient conditions.  
- Adjust the thermostat knob to give correct temperature  
control. See page 4.  
The compressor runs continuosly  
- Check that the door is closed.  
- Large quantities of food have recently been placed in  
the cabinet and/or door is frequently opened.  
- Check that air ventilation is not obstructed.  
- Ensure the door is not left open.  
Excessive frost and ice has built up  
- Check that nothing is preventing the door from closing.  
- Is the door gasket intact and clean.  
- Refer to normal operating sounds.  
Noise  
- Check the drain hole is not blocked. (see Maintenance  
and Cleaning).  
Water under the salad drawers  
If after the above checks, there is still a fault, call your local Service Force Centre.  
In-guarantee customers should ensure that the above checks have been made as the engineer will make a  
charge if the fault is not a mechanical or electrical breakdown.  
Please note that proof of purchase is required for any in-guarantee service calls.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND SPARE PARTS  
Before calling out an engineer, please ensure you  
have read the details under the heading ‘Something  
Not Working’.  
In the event of your appliance requiring service, or if  
you wish to purchase spare parts, please contact your  
local Zanussi Service Force Centre by telephoning:-  
When you contact the Service Centre you will need  
to give the following details.  
08705 929929  
1. Your name, address and post code  
2. Your telephone number  
Your telephone call will be automatically routed to the  
Service Force Centre covering your post code area.  
The addresses are listed on the following pages.  
3. Clear and concise details of the fault  
4. The model serial no. of the appliance (found on  
the rating plate)  
5. The purchase date  
CUSTOMER CARE DEPARTMENT  
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, you  
are invited to contact our Customer Care Department by letter or telephone or visit our website at  
Customer Care Department  
Zanussi  
55-77 High Street  
Slough  
Berkshire  
SL1 1DZ  
Tel: 08705 727727 ( )  
*
( ) calls to this number may be recorded for training purposes.  
*
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUARANTEE CONDITIONS  
Standard guarantee conditions  
We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part there-  
of is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or  
replace the same FREE OF CHARGE for labour, materials or carriage on condition that:  
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.  
The appliance has been used for normal domestic purposes only, and in accordance with the manufactuer's  
instructions.  
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not  
authorized by us.  
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.  
Any appliance or defective part replaced shall become the Company's property.  
This guarantee is in addition to your statutory and other legal rights.  
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these  
hours in which case a premium will be charged.  
Exclusions  
This guarantee does not cover:  
Damage or calls resulting from transportation, improper use or neglect, thc replacement of any light bulbs or  
removable parts of glass or plastic.  
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside  
the United Kingdom.  
Appliances found to be in use within a commercial environment, plus those which are subject to rental  
agreements.  
Products of Zanussi manufacture which are not marketed by Zanussi.  
European Guarantee  
If you should move to another country within Europe then your guarantee moves with you to your new home  
subject to the following qualifications:  
The guarantee starts from the date you first purchased your product.  
The guarantee is for the same period and to the same extent for labour and parts as exists in the new  
country of use for this brand or range of products.  
This guarantee relates to you and cannot be transferred to another user.  
Your new home is within European Community (EC) or European Free Trade Area.  
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a  
normal household.  
The product is installed taking in account regulations in your new country.  
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your  
new home. They will then ensure that the local Service Organisation is aware of your move and able to look  
after you and your appliance.  
France  
Germany  
Italy  
Senlis  
+33 (0) 44 62 29 99  
+49 (0) 911 323 2600  
+39 (0) 1678 47053  
+46 (0) 8 738 79 50  
+44 (0) 1753 219897  
Nurenberg  
Pordenone  
Stockholm  
Slough  
Sweden  
UK  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TECHNICAL SPECIFICATIONS  
DIMENSIONS  
Height  
Width  
Depth  
81,5  
59,6  
53,8  
cm  
cm  
cm  
POWER SUPPLY VOLTAGE AND FREQUENCY  
TOTAL POWER ABSORBED  
220-240 V / 50 Hz  
70 W  
AVERAGE DAILY UNITS ELECTRICITY(*)  
0,49 kWh  
GROSS CAPACITY  
NET CAPACITY  
142 l  
140 l  
(*)This figure is based on standard test results in accordance with European Standard EN153. Actual con-  
sumption will depend on how the appliance is used and where it is located.  
INSTALLATION  
Positioning  
For this appliance to work efficiently, it should be  
located away from heat sources, e.g. cookers, radia-  
tors, boilers, direct sunlight etc. Best performance is  
obtained with ambient temperature between +10°C  
and +32°C.  
For building-in and door reversibility, if necessary,  
refer to the relevant instructions in the following  
pages.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELECTRICAL CONNECTION  
This appliance complies with the E.E.C.  
WARNING:  
Directive No. 87/308 of 2.6.87 relative to radio  
interference suppression.  
THIS APPLIANCE MUST BE EARTHED.  
The manufacturer declines any liability  
should this safety measure not be observed.  
A replacement cover/carrier must be obtained  
from your local Zanussi Service Force Centre  
whose address is listed in the Customer Care  
Booklet which accompanies your instruction man-  
ual.  
If the plug that is fitted to your appliance is not suit-  
able for your socket outlet, it must be cut off and the  
appropriate plug fitted.  
Remove the fuse from the cut off plug.  
The cut off plug should then be disposed of to prevent  
the hazard of shocks in case it should be plugged into  
a 13amp socket in another part of your home.  
This appliance complies with the following  
E.E.C. Directive:  
- 73/23 EEC of 19.2.73 (Low Voltage Directive)  
and subsequent amendments.  
Important  
- 89/336 EEC of 3.5.89 (Electromagnetic  
- Compatibility Directive) and subsequent amend-  
ments.  
The wires in the mains lead are coloured in  
accordance with the following code:  
Please ensure that when the appliance is  
installed it is easily accessible for the engineer  
in the event of breakdown.  
Green and Yellow  
Blue  
Brown  
- Earth  
- Neutral  
- Live  
If you fit your own plug, the colours of the wires in the  
mains lead of your appliance, may not correspond  
with the markings identifying the terminals in your  
plug, proceed as follows:  
Connect the Green and the Yellow (earth) wire to the  
terminal in the plug which is marked with the letter  
GREEN & YELLOW  
13 AMP. FUSE  
«E» or the earth symbol  
yellow.  
, or coloured green and  
Connect the blue (neutral) wire to the terminal in the  
plug which is marked with the letter «N» or coloured  
black.  
Connect the brown (live) wire to the terminal in the  
plug which is marked with the letter «L» or colured  
red.  
BROWN  
BLUE  
CORD CLAMP  
D207  
The plug moulded onto the lead incorporates a fuse.  
For replacement, use a 13amp BS1362 fuse. Only  
ASTA or BSI approved fuses should be used.  
The plug must not be used if the fuse cover/carrier is  
lost. The cover/carrier is indicated by the coloured  
insert at the base of the plug.  
A replacement cover/carrier must be obtained from  
your local Zanussi Service Force Centre.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BUILDING-IN INSTRUCTIONS  
Before carrying out any work, remove the plug from  
the power socket.  
Door Reversal  
Left door opening:  
1. Remove the grid from the appliance pulling it  
towards you with hands.  
2. Remove the left side (A) of the grid cutting it from  
A
the rear (see figure).  
DO002  
To reposition the grid on the appliance proceed as fol-  
lows:  
a
Apply the grid to the base of the appliance by pushing  
the clasps (a) until they click.  
N.B. The grid is to be assembled after having fixed  
the appliance in the niche with the brackets.  
a
DO001  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To reverse the opening direction of the door, proceed as  
shown in the figures:  
Attention  
After completion of the door reversing opera-  
tion, check that the door gasket adheres to the  
cabinet. If the ambient temperature is cold (i.e.  
in Winter), the gasket may not fit perfectly to  
the cabinet. In that case, wait for the natural fit-  
ting of the gasket or accelerate this process by  
heating up the part involved with a normal  
hairdryer on a low setting.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Building the appliance in under a  
worktop  
The dimensions of the recessed installation area must  
correspond with those indicated in the figure.  
DO013  
Remove covering and adjusting strips.  
Push the appliance into place. The plug socket neces-  
sary for connection of the appliance to the electricity  
supply should be positioned, so that the plug is not  
placed in the recess.  
S.I.005  
Adjust height.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To mount the furniture door proceed as shown in the  
figures:  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Screw appliance into place.  
Refit the covering strip.  
Fitting the plinth  
Important  
For the efficient operation of the appliance, it  
is important that the original ventilation grid is  
used.  
For an opening height dimension A=820 mm and a  
plinth height dimension a=100 mm, the plinth may  
be fitted without adjustments. The same applies to  
an opening height dimension B=870 mm and a  
plinth height dimension b=150 mm.  
For plinth heights greater than a=100 mm, b=150  
mm, a cut should be made in the plinth, 580 mm  
wide, in the centre of the appliance position, leav-  
ing a remaining height of a=100 mm, b=150 mm.  
Attach plinth to the kitchen units.  
25  
Important  
DO008  
The plinth must be positioned at a minimun  
distance of 25 mm from the door.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© Electrolux Household Appliances Limited 2000  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Weider Home Gym WESY59933 User Manual
West Bend Microwave Oven AG028PLV User Manual
Westinghouse Microwave Oven WCM660W User Manual
Westinghouse Power Hammer DBN40S User Manual
Whirlpool Clothes Dryer CGM2941TQ0 User Manual
Whirlpool Washer WTW6200SW1 User Manual
Xantrex Technology Universal Remote RC GS RC7 User Manual
Yamaha Outboard Motor F75B User Manual
Zanussi Pasta Maker 200380 User Manual
Zanussi Washer ZFL850 User Manual