REFRIGERATOR
ZU 9124
INSTRUCTION BOOKLET
2222682-42
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
These warnings are provided in the interests of your safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings or these warnings contact the Customer Care Departement.
Prior to Installation
General Safety
■ Check the appliance for transport damage. Under
no circumstance should a damaged appliance be
installed. In the event of damage please contact
your retailer.
■ This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging
must therefore only be carried out by autho-
rised technicians.
■ Take utmost care when handling your appli-
ance so as not to cause any damages to the
cooling unit with consequent possible fluid
leakages.
Installation
■ This appliance is heavy. Care should be taken
when moving it.
■ The appliance must not be located close to
■ It is dangerous to alter the specifications or
radiators or boilers.
attempt to modify this product in any way.
■ Avoid prolonged exposure of the appliance to
■ Ensure that the appliance does not stand on the
electrical supply cable.
direct sunlight.
■ Do not use other electrical appliances (such
as ice cream makers) inside of refrigerating
appliances.
Important: if the supply cable is damaged, it
must be replaced by a cable available from the
manufacturer or your local Service Force Centre.
■ Any electrical work required to install this appli-
ance should be carried out by a qualified electri-
cian or competent person.
During Use
■ This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs
only. It is not intended for commercial or industri-
al use.
■ Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the required
distance for ventilation, as states in the installa-
tion instructions.
■ Containers with flammable gases or liquids can
leak at low temperatures. Do not store any con-
tainers with flammable materials, such as spray
cans, fire extinguisher refill cartridges etc. in the
refrigerator.
■ The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
■ Frozen food should not be refrozen once it has
Refrigerant
thawed out.
■ Do not place carbonated or fizzy drinks in the
■ The refrigerant isobutane (R600a) is contained
within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental
compatibly, which is nevertheless flammable.
freezer compartment.
■ Ice lollies can cause ‘frost/freezer burns’ if con-
sumed straight from the star compartement.
■ During transportation and installation of the appli-
ance, be certain that none of the components of
the refrigerant circuit become damaged.
■ Do not remove items from the freezer comparte-
ment if your hands are damp/wet, as this could
cause skin abrasions or frost/freezer burns.
■ Bottles and cans must not be placed in the freez-
er compartment they can burst when the con-
tents freeze.
■ If the refrigerant circuit should become damaged:
- avoid open flames and sources of ignition.
- thoroughly ventilate the room in which the appli
ance is situated.
■ Manufacturers’ recommended storage times
should be adhered to.Refer to relevant instruc-
tions.
Child Safety
■ Do not allow children to tamper with the controls
Maintenance and Cleaning
or play with the product.
■ Before cleaning, always switch off the appliance
■ There is a risk of suffocation! Keep packaging
and disconnect from the electrical supply.
material away from children!
■ When unplugging always pull the plug from the
mains socket, do not pull on the cable.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Servicing
■ This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
■ Under no circumstances should you attempt to
repair the appliance yourself.Repairs carried out
by inexperienced persons may cause injury or seri-
ous malfunctioning. Contact your local Zanussi
Service Force Centre.
At the end of the Appliance Life
■ When disposing of your appliance use an autho-
rised disposal site.
■ Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
DESCRIPTION OF THE APPLIANCE
Dairy compartment
➀
Movable shelf
➁
Bottle storage shelf
➂
➆
Salad bin
➀
➁
➃
➄
➅
➆
Storage shelves
Thermostat control
Freezer compartment
➅
➄
➃
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Before use
Remove all securing tapes. Wash inside the appli-
ance with lukewarm water and bicarbonate of soda
(5 ml to 0.5 litre of water). Do not use soap or deter-
gent as the smell may linger. Dry thoroughly.
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad drawers.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Milk bottles: these should have a cap and should
be stored in the bottle rack on the door.
Setting the temperature
The walls of the refrigerator are equipped with run-
ners so that shelves can be positioned as desired.
For better use of space, the front half-shelf can lie
over the rear one (see fig.).
The temperature inside the refrigerator is regulated
by a thermostat with 6 temperature positions and
one «OFF» (O) position.
Position 1 = minimum coldness
Position 6 = maximum coldness
Turn the thermostat dial to the required position.
An intermediate position is usually the most suitable,
although the temperature will be affected by:
l
Room temperature
l How often the door is opened
l How much food is stored
l Position of the appliance
In determining the correct temperature control setting
all these factors have to be considered and some
experimentation may be necessary.
D338
When altering the temperature setting, allow 24
hours for the temperature to stablise before making
further changes.
The door shelves
Depending on the use of the bottle shelf (3) the
short shelf (2) can be adjusted in the direction of the
arrow (a).
For more thorough cleaning, shelves can be
removed, then refitted in their position. To make
these adjustements proceed as follows:
top shelf (1): gradually pull in the direction of the
arrows until it comes free;
Important
During prolonged periods of abnormally
hot weather, if the thermostat is set on too
high a number, the cooling system may
operate continuously and the fridge cool-
ing plate may not defrost. Turning the knob
to a lower number will cause the automatic
defrosting to resume.
middle shelf (2): turn it in the direction of the arrows
until it comes free from the metallic crosspiece (4);
bottle shelf (3): push on the buttons (b) until it
comes free, then pull it in the direction of the arrow.
Fresh food refrigeration
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Do not cover the shelves with any protective materi-
al, such as paper, cardboard or plastic, which may
obstruct the air circulation through them.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb & chicken or poul-
try): wrap in polythene bags and place on top of the
salad drawers.
Meat can only be stored safely in this way for
one or two days at the most.
1
4
2
a
b
3
S.I.010
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The
-star compartment
Thawing
This compartment is suitable for freezing fresh food,
for the storage of commercially frozen food and for
ice cube making.
Food can be thawed in a number of ways, depend-
ing on the type of food and the size of the packs.
Meat, fish and fruit should be thawed in the refriger-
ation compartment and small pieces of meat can
even be cooked while still frozen, but you must
ensure that it is thoroughly cooked through.
Vegetables should be directly immersed in boiling
water; ready-cooked dishes can be placed directly in
the oven in their aluminium wrapping.
A microwave oven is particularly suitable for thawing
any type of frozen or deep-frozen food: follow the
oven instructions, particularly regarding the place-
ment of aluminium wrapping in the oven.
Freezing fresh food
To freeze fresh foods it is not necessary to change
the setting of the thermostat knob.
However, for a quicker freezing operation, turn the
thermostat knob to the coldest setting; but remem-
ber that, in this condition, the refrigerator compart-
ment temperature might drop below 0°C. If this
occurs reset thermostat knob to a warmer setting.
Only freeze top quality, fresh and thoroughly
cleaned foodstuffs.
Making ice cubes
Do not allow fresh food to touch food which is
already frozen.
During the freezing process, ensure that the freezer
compartment door remains closed.
The appliance is provided with a plastic ice cube
tray. Fill the tray 3/4 full to allow the ice to expand
and place it in the
-star compartment. To
turn out the ice cubes simply give the tray a slight
twist to release the cubes.
Frozen food storage
Important
Storing ready-frozen foods is quite straightforward.
The packs can be placed beside each other or on
top of each other.
You are strongly advised to place ready-frozen food
in the compartment as quickly as possible after pur-
chase and we therefore recommend that you buy
them last. Also ensure that the external packaging is
intact.
Do not consume ice-lollies which have just
come out of the
-star compartment.
Their extremely low temperature can cause
frost burns. Do not remove items from the
-star compartment if your hands are
damp/wet, as this could cause skin abrasions
or "frost/freezer burns".
Packaging which is swollen or has traces of refrozen
water droplets on the pack could indicate that the
product has not been kept at a suitable temperature
and that it may have lost its original quality.
Partially thawed food must not be refrozen, it must
be consumed within 24 hours.
Normal Operating Sounds
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
below, to the cooling evaporator.
When the compressor is on, the refrigerant is being
pumped round, and you will hear a whirring sound
or pulsating noise from the compressor. A thermo-
stat controls the compressor, and you will hear a
faint ‘click’ when the thermostat cuts in and out.
Never exceed the storage times indicated.
Do not open the
-star compartment door
too often and do not leave open longer than neces-
sary.
Important
In the event of a power cut do not open the
door. The food in the
star compart-
-
ment will not be affected if the power cut is
short and if the compartment is full. Should
the food begin to thaw, it must be consumed
quickly and must not be re-frozen.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HEALTH AND SAFETY GUIDELINES
Because of consumer demand, preservatives have been removed from many pre-prepared foods. This
together with the changes in shopping habits to a once-a-week shop, mean that safe handling and
storage of food is even more important than ever.
The following tips should help you to ensure
that the food in your home is in as perfect condi-
tion as possible.
■
Keep the time between buying chilled food and
placing it in your fridge as short as possible.
Tests showed that the temperature of 1 litre of
orange juice rose to 22°C in an hour between the
supermarket and home. It then took 11 hours to
get down to 7°C in the refrigerator.
■ Packaging which is swollen or has traces of
refrozen water droplets on the pack could indi-
cate that the product has not been kept at a suit-
able temperature and that it may have lost its
original quality. Partially thawed food must not be
refrozen, it must be consumed within 24 hours.
Never exceed the storage time indicated.
■
■
■
Keep the refrigerator door closed as much as
possible.
■ Never place hot food, bottles or cans of fizzy
drink in the freezer compartment as they may
explode. Containers with a lid must not be filled
to the brim.
Do not push food together too much, try to allow
air to circulate around each item.
Cool cooked food as quickly as possible but do
NOT place in the refrigerator until cool. (Leave
food in a cool place in order that it can then be
placed in the refrigerator as soon as possible).
■ Do not open the door or place extra fresh food in
the freezer compartment next to food which is
already frozen as this could cause the tempera-
ture of the frozen food to rise and its quality and
storage life to reduce.
■
■
Do NOT mix raw and cooked meat, they must be
in separate containers. Take care not to let the
meat juices drip onto other food. If the meat does
drip, remove everything and clean thoroughly.
■
Remove suspect food from your refrigerator and
clean (Refer to “Maintenance and Cleaning”).
■
Never allow spillages to dry and harden.
Do not store food uncovered.
■
Store eggs in the egg rack provided in the refrig-
■ The best way to defrost food is to put it in the
erator door. Discard any broken or chipped eggs.
refrigerator to thaw slowly.
■
Regularly check the refrigerator and the freezer
■ Ensure that food placed in the freezer compart-
ment is dated and labelled and used in date
order to ensure that food is consumed at its best.
door seals to ensure that they are clean and free
from debris.
■
Always wash your hands with soapy water and
■ It is important that food is used before its “best
dry them with a clean towel before handling food.
before” date.
■
Keep work surfaces clean and avoid cross conta-
■ The foods to be frozen must be fresh and of the
mination by not using the same work surface or
knife, without washing them thoroughly in
between.
best quality.
■ The size of each pack should be small enough to
ensure that it is used in one go. Small packs
freeze more quickly and uniformly and give better
results.
■ Frozen food, once thawed, must not be refrozen.
Lean food keeps better and longer than fatty
food, salt reduces the storage time.
■ Wrap the food in polythene or aluminium freezing
bags or foil so that they adhere to the food and
provide an airtight seal.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFROSTING
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located beneath the appliance adja-
cent to the compressor, where it evaporates.
Important
To avoid defrost water overflowing and dripping
onto the food in the fridge, periodically clean
the water discharge hole (F) situated under the
salad bins. Use the special cleaner provided
(P) which you will find already inserted into the
discharge hole
P
F
S.I.011
The freezer compartment, however, will become pro-
gressively covered with frost. This should be removed
with the special plastic scraper provided, whenever
the thickness of the frost exceeds 4 mm. During this
operation it is not necessary to switch off the power
supply or to remove the foodstuffs.
Never use sharp metal tools to scrape off frost
from the evaporator as you could damage it.
Do not use a mechanical device or any artificial
means to speed up the thawing process other than
those recommended by the manufacturer.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
as follows:
1. pull out the plug from the wall socket or turn the
thermostat knob to the «O» setting;
2. remove any stored food, wrap it in several layers of
newspaper and put it in a cool place;
3. leave the door open, place a basin on the top shelf
of the refrigerator compartment, under the drain
hole, remove the plug as shown in the figure;
4. when defrosting is completed, dry the interior
thoroughly and refit the plug.
Keep the scraper for future use; turn the thermostat
knob back to the required setting or replace the plug
in the power socket. After two or three hours, reload
the previously removed food into the compartment.
PR151
Important
A temperature rise of the frozen food packs,
during defrosting, may shorten their safe stor-
age life.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the ELEC-
TRICITY supply.
Changing the light bulb
Should the interior light fail to work, first switch off
the appliance and disconnect from the electricity
supply, then replace the bulb as follows:
Warning
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must
therefore only be carried out by authorised
technicians.
1. Unscrew the light cover and then pull it outward
by pressing as shown in the figure. Unscrew the
bulb and replace it with a new 15 watt bulb (avail-
able from your nearest Zanussi Service Force
centre).
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE POW-
DERS, HIGHLY PERFUMED CLEANING PROD-
UCTS OR WAX POLISHES, TO CLEAN THE INTE-
RIOR AS THESE WILL DAMAGE THE SURFACE
AND LEAVE A STRONG SMELL.
Clean the drain hole of the water trough at regular
intervals and make sure that the drain hole is never
obstructed, so that the defrost water may flow freely.
D411
2. Replace the light cover by sliding it into its original
position and replacing the screw.
Important
Do not use abrasive products.
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the door ajar
to prevent unpleasant smells.
Periodic cleaning
The appliance is equipped with a ventilation grid.
Keep clean to guarantee good ventilation and good
working order of the appliance.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity con-
sumption.
The structure of the appliance permits to clean the
rear zone close to the wall, using a vacuum cleaner.
1. Remove the plinth (1), then the ventilation grid (2);
2. Carefully pull the air deflector out (3), checking
that there is no water left from the defrosting.
3
2
1
S.I.013
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SOMETHING NOT WORKING?
Before contacting your local Service Force Centre check the following points.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
No power to appliance
Solution
- Check there is power at the socket.
- Check there is not a power cut by checking the
household lights.
- Check the fuse has not blown.
- Ensure that the bulb is correctly fitted.
- Replace the bulb if it has blown.
The light does not come on
- Check the door light switch is not jammed.
- Check the ambient temperature is within the appliances
operating limits of 10˚C to 32˚C.
The temperature in the fridge is too high
Relocate the appliance if necessary.
- Check the thermostat control knob is turned to the
correct setting relative to ambient conditions.
- Adjust the thermostat control knob to give correct
temperature control. See page 5.
- Check that the door is closed.
- Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
- Check that air ventilation is not obstructed.
The compressor runs continuously
Excessive frost and ice has built up
- Ensure the door is not left open.
- Check that nothing is preventing the door from closing.
- Is the door gasket intact and clean?
- Refer to normal operating sounds.
Noise
- Check the drain hole is not blocked (see “Maintenance
and Cleaning”).
Water under the salad drawers
If after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if
you wish to purchase spare parts please contact your
local Zanussi Service Force Centre by
telephoning:
Before calling out an engineer, please ensure you
have read the details under the heading ‘Something
Not Working?’
When you contact the Service Centre you will need
to give the following details.
1. Your name, address and post code
2. Your telephone number
08705 929929
3. Clear and concise details of the fault
4. The model serial no. of the appliance (found on
the rating plate)
Your call will be automatically routed to the Service
Force Centre covering your post code area. The
address of your local Service Force Centre is detailed
in the accompanying Customer Care Book.
5. The purchase date
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, you
are invited to contact our Customer Care Department by letter or telephone or visit our website at
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727727 ( )
*
( ) calls to this number may be recorded for training purposes.
*
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part there-
of is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
■
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
■
The appliance has been used for normal domestic purposes only, and in accordance with the manufactuer's
instructions.
■
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorized by us.
■
■
■
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
Any appliance or defective part replaced shall become the Company's property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
■
■
■
■
Damage or calls resulting from transportation, improper use or neglect, thc replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
■
The guarantee starts from the date you first purchased your product.
■
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
■
■
■
This guarantee relates to you and cannot be transferred to another user.
Your new home is within European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
■
The product is installed taking in account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliance.
France
Germany
Italy
Senlis
+33 (0) 44 62 29 99
+49 (0) 911 323 2600
+39 (0) 1678 47053
+46 (0) 8 738 79 50
+44 (0) 1753 219897
Nurenberg
Pordenone
Stockholm
Slough
Sweden
UK
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
Width
Depth
81,5
59,6
53,8
cm
cm
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
220-240 V / 50 Hz
80 W
AVERAGE DAILY UNITS ELECTRICITY(*)
0,58 kWh
TOTAL GROSS CAPACITY
122 l
NET CAPACITY
NET CAPACITY
Fridge
102 l
18 l
compartment
STAR RATING
(*)This figure is based on standard test results in accordance with European Standard EN153. Actual con-
sumption will depend on how the appliance is used and where it is located.
INSTALLATION
Positioning
For this appliance to work efficiently, it should be
located away from heat sources, e.g. cookers, radia-
tors, boilers, direct sunlight etc. Best performance is
obtained with ambient temperature between +10°C
and +32°C.
For building-in and door reversibility, if necessary,
refer to the relevant instructions in the following
pages.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CONNECTION
This appliance complies with the E.E.C.
WARNING:
Directive No. 87/308 of 2.6.87 relative to radio
interference suppression.
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability
should this safety measure not be observed.
A replacement cover/carrier must be obtained
from your local Zanussi Service Force Centre
whose address is listed in the Customer Care
Booklet which accompanies your instruction man-
ual.
If the plug that is fitted to your appliance is not suit-
able for your socket outlet, it must be cut off and the
appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent
the hazard of shocks in case it should be plugged into
a 13amp socket in another part of your home.
This appliance complies with the following
E.E.C. Directive:
- 73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent amendments.
- 89/336 EEC of 3.5.89 (Electromagnetic
- Compatibility Directive) and subsequent amend-
ments.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of breakdown.
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
If you fit your own plug, the colours of the wires in the
mains lead of your appliance, may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
Connect the Green and the Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
yellow.
, or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or colured
red.
BROWN
BLUE
CORD CLAMP
D207
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BS1362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre whose
address is listed in the Customer Care Booklet which
accompanies your instruction manual.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BUILDING-IN INSTRUCTIONS
Before carrying out any work, remove the plug from
the power socket.
Inner door reversal
1. Using a screwdriver release bracket (1) by pressing
on the internal spring (Fig.) and withdraw it from its
seat together with the door;
2. remove plug (2) and fit it in the hole left open on
the opposite side;
3. turn the door through 180°, remove the bracket (1)
180°
and refit it on the opposite side.
2
4. Refit the door and insert the top pin and bottom
bracket (1), pushing it into place.
1
To ensure correct storage of food, the door is fitted
with a simple spring device which holds it in the open
position until it is properly closed.
PR140
Door reversal
Left door opening:
1. Remove the grid from the appliance pulling it
towards you with hands.
2. Remove the left side (A) of the grid cutting it from
the rear (see figure).
A
DO002
To reposition the grid on the appliance proceed as fol-
lows:
Apply the grid to the base of the appliance by pushing
the clasps (a) until they click.
a
N.B. The grid is to be assembled after having fixed
the appliance in the niche with the brackets.
a
DO001
17
Download from Www.Somanuals.com. All Manuals Search And Download.
To reverse the opening direction of the door, proceed as
shown in the figures:
Attention
After completion of the door reversing opera-
tion, check that the door gasket adheres to the
cabinet. If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to
the cabinet. In that case, wait for the natural fit-
ting of the gasket or accelerate this process by
heating up the part involved with a normal
hairdryer on a low setting.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Building the appliance in under a
worktop
The dimensions of the recessed installation area must
correspond with those indicated in the figure.
DO013
Remove covering and adjusting strips.
Push the appliance into place. The plug socket neces-
sary for connection of the appliance to the electricity
supply should be positioned, so that the plug is not
placed in the recess.
S.I.005
Adjust height.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
To mount the furniture door proceed as shown in the
figures:
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Screw appliance into place.
Refit the covering strip.
Fitting the plinth
Important
For the efficient operation of the appliance, it
is important that the original ventilation grid is
used.
■ For an opening height dimension A=820 mm and a
plinth height dimension a=100 mm, the plinth may
be fitted without adjustments. The same applies to
an opening height dimension B=870 mm and a
plinth height dimension b=150 mm.
■ For plinth heights greater than a=100 mm, b=150
mm, a cut should be made in the plinth, 580 mm
wide, in the centre of the appliance position, leav-
ing a remaining height of a=100 mm, b=150 mm.
■ Attach plinth to the kitchen units.
25
Important
DO008
The plinth must be positioned at a minimun
distance of 25 mm from the door.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
© Electrolux Household Appliances Limited 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
|