MIXED FUEL
COOKERS
ZCM 650
ZCM 651
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
You MUST read these warnings carefully before installing or using the hob. If you need assistance,
contact our Customer Care Department on 08705 727727
Installation
cable does not come into contact with the hot
surfaces of the cooker.
•
Appliances in the UK must be installed and serviced
by a competent person as stated in the Gas
Safety(Installation and Use) Regulations Current
Editionsand the IEE Wiring Regulations.
•
Unstable or misshapen pans should not be used on
the hob burners as unstable pans can cause an
accident by tipping or spillage.
•
For appliances installed in the Republic of Ireland
please refer to NSAI-Domestic Gas Installations
I.S.813 Current Editions and the ETCI Rules for
Electrical Installations.
•
•
•
Never leave the cooker unattended when cooking with
oil and fats.
This cooker should be kept clean at all times. Abuild-
up of fats or foodstuffs could result in a fire.
•
•
•
This cooker is heavy. Take care when moving it.
Remove all packaging before using the cooker.
Never use plastic dishes in the oven or on the hob
burners. Never line any part of the oven with aluminium
foil.
Some parts have a shock-resistant plastic film
protection. Be sure to remove this plastic film before
you start operating the appliance and clean the parts
involved using a soft cloth wrung out in warm water
to which a little washing up liquid has been added.
•
•
Always ensure that the oven vent which is located at
the centre back of the hob is left unobstructed to
ensure ventilation of the oven cavity.
•
•
Ensure that the gas and electrical supply complies
with the type stated on the rating plate, located near
the gas supply pipe.
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above the
cooker.
Do not attempt to modify the cooker in any way.
Service
Child Safety
•
This cooker should only be repaired or serviced by an
authorised Service Engineer and only genuine
approved spare parts should be used.
•
•
•
This cooker is designed to be operated by adults. Do
not allow children to play near or with the cooker.
The cooker gets hot when it is in use. Children should
be kept away until it has cooled.
Environmental Information
Children can also injure themselves by pulling pans
or pots off the cooker.
•
•
After installation, please dispose of the packaging
with due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
During Use
•
This cooker is intended for domestic cooking only. It
is not designed for commercial or industrial purposes.
•
When in use a gas cooker will produce heat and
moisture in the room in which it has been installed.
Ensure there is a continuous air supply, keeping air
vents in good condition or installing a cooker hood
with a venting hose.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
This appliance is manufactured according to
the following EEC directives:
73/23 EEC - 90/683 EEC - 93/68 EEC -
89/336 EEC - 90/396 EEC,
•
When using the cooker for a long period of time, the
ventilation should be improved, by opening a window
or increasing the extractor speed.
current edition.
•
•
•
Do not use this cooker if it is in contact with water.
Do not operate the cooker with wet hands.
Ensure the control knobs are in the ‘OFF’ position
when not in use.
These instructions are only valid in the
countries whose symbols appear on this
booklet's cover.
During use the appliance becomes hot. Care should
be taken to avoid touching heating elements inside
the oven.
•
When using other electrical appliances, ensure the
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
For the User
Important Safety Information
Control Panel
For the Installer
Instructions for the Installer
Important Safety Requirements
Installation
3
5
30
30
31
33
34
34
The Gas Hob Controls
Electric Oven
6
7
Electrical Connections
Commissioning
Electric Programmer
Before the First Use of the Cooker
Programming the Oven
Safety and Energy saving functions
Using the Oven
8
10
11
14
15
15
16
17
18
19
20
21
22
27
28
28
29
Conversion from Natural Gas to LPG
Hints and Tips
Using the Conventional Oven
Cooking Chart - Conventional Oven
Pizza Oven
Grilling
Defrosting
Maintenance and Cleaning
Cleaning the Oven
Something not working
Service and Spare Parts
Customer Care Department
Guarantee Conditions
Guide to Use the Instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
Hints and Tips
)
Environmental Information
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel
1
2
3
4
5
6
7
1. Back left burner control knob (semi-rapid)
5. Electronic Programmer
2. Front left burner control knob (ultra-rapid triple
6. Oven function control knob
7. Time/Temperature control knob
crown)
3. Front right burner control knob (auxiliary)
4. Back right burner control knob (semi-rapid)
The Oven Cavity
Grill element
Oven Light
Accessories
Grill/roasting pan
Grill trivet
Removable
handles
Oven fan
2 anti-tip
shelves
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Gas Hob Controls
To light a burner:
)
z
turn the relevant control knob anticlockwise to the
maximum position, then push it down to ignite the
burner;
z
upon ignition, keep the knob pushed down about 5
seconds. This will allow the "thermocouple" (see
diagram, D) to be heated and the safety device to be
switched off, otherwise the gas supply would be
interrupted.
z
then, check the flame is regular and adjust it as
required.
If you cannot light the flame even after several attempts,
check the "cap" and “crown” (see diagram, A-B) are in
the correct position.
To put the flame out, turn the knob to the symbol z.
When switching on the mains, after installation or
a power cut, it is quite normal for the spark
generator to be activated automatically.
If you use a saucepan which is smaller than the
recommended size, the flame will spread beyond
the bottom of the pan, causing the handle to
overheat.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
If the control knobs become difficult to turn, please
contact your local Service Force Centre.
Triple-crown Burner
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
A
B
Burner
minimum
diameter
maximum
diameter
Large(ultrarapid
triplecrown)
Medium(semi-rapid)
Small(auxiliary)
D
C
180 mm
120 mm
80 mm
260 mm
220 mm
160 mm
A - Burner cap
B - Burner crown
C - Ignition electrode
D - Thermocouple
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Oven
Oven Function Control Knob
Oven Light - The oven light will be on without
any cooking function.
Conventional cooking - The heat comes
from both the top and bottom element, ensuring
even heating inside the oven. Pre-set
temperature: 200 °C
Pizza Oven - The bottom element provides
direct heat to the base of pizzas, quiches or
pies, while the fan ensures air is circulated to
cook the pizza toppings or pie fillings. Pre-set
temperature: 175 °C
Inner Grill - It can be used for grilling small
quantities. Pre-set temperature: 250 °C
Top heating element - The heat comes from
thetop of the oven only. Pre-set temperature:
250 °C
Full Grill - The full grill element will be on.
Pre-set temperature: 250 °C
Defrostsetting-Thisfunctionassistsinthawing
of frozen food. Pre-set temperature: 30 °C
Pyrolytic cleaning - This special function
allowsyoutoclean thoroughlytheovencavity.
Time/Temperature Control knob
The time/temperature control knob allows you to select
the time (minute minder, cooking duration and end of
cookingtime)andtemperature.
Turn it clockwise
and hold it in the turned position to
increasethetime/temperaturesetting.Turnitanticlockwise
andholditintheturnedpositiontodecreasethetime/
temperaturesetting.Thecount-uporcount-downspeed
increases the longer the knob is held in the turned
position.
Cooling fan
The cooling fan operates during cooking. Air is expelled
through vents between the oven door and the control panel,
as shown in the diagram. The cooling fan may run on after
the oven is switched off to keep the controls cool. This is
quite normal.
The Safety Thermostat
This oven is provided with a safety thermostat. In case of
malfunctioning of the main thermostat, and consequent
over-heating, the safety device will stop the power supply
to the appliance. If this happens, call your local Service
Force Centre. Under no circumstances should you attempt
to repair the appliance yourself.
FO 2259
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Electronic programmer
9
1. “Cook time” indicator
2. "Temperature" button for displaying the temperature
inside the oven
8
7
3. “End Time” indicator
4. “Pyrolytic” button for activating the pyrolytic cleaning
1
cycle
5. “Minute minder” indicator
6. “Time” button for selecting the time functions
7. “Time” indicator
8. Temperature level indicators
9. Display
3 4
5
6
2
In case of loss of power, all the settings (time of
day, set programme or programme in operation),
will be cancelled. When the power is restored,
the numbers on the display will flash, and the ti-
mer has to be reset.
The oven will work only if the time of day has
been set.
However, the oven can also be operated without
any programme.
How to set the time of day
When the power supply is switched on, or after a power
failure,thedisplaywillautomaticallyshow12.00andthe
indicator “Time” will flash in the display.
Ensure the correct time of day is set before using the
oven.
To set the correct time of day:
1. Turn the Time/Temperature control knob to
or
to adjust the time in 1 minute degree step.
2. After the setting is carried out, wait for 5 seconds:
the “Time” indicator will go out and the display will
show the set time. The appliance is ready for use.
To reset the correct time of day:
1. Press button “Time” repeatedly to select the “Time“
function. The relevant indicator will start flashing. Then
proceed as described above.
The time of day can only be reset if no automatic
function (cook duration or end of cooking) has been
set.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
How to select a cooking function
and set the temperature
Theovenhassevendifferentcookingfunctions.
1. Turn the oven control knob and select the required
cooking function. Each time a cooking function is
selected, a pre-set temperature will appear in the
display.
2. If the pre-set temperature is not suitable, turn the Time/
Temperature control knob to
or
to adjust the
temperature in 5 degree steps.
After choosing the temperature, the oven starts heating
up and the temperature level indicators will light up.
Push button “Temperature” to display the
temperature inside the oven cavity.
Temperature level indicators
As soon as the oven heats up, the temperature level
indicators light up, indicating the degree to which the
oven is currently heated.
When the required temperature is reached, an acoustic
alarm will sound for a short time and all the temperature
level indicators will light permanently.
After the oven is switched off, the indicators will stay on
until the temperature reaches 40 °C.
Special functions
The following functions can be activated by pressing a
button and turning the time/temperature control knob at
the same time:
- Child lock: turn the time/temperature control knob to
and press “Time” button.
- Display switched on/off: turn the time/temperature con-
trol knob to
and and press “Time” button.
For further details, see chapter “Safety and Energy Sav-
ing functions”.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Before the First Use of the Cooker
Remove all packaging, both inside and outside
the oven, before using the oven.
Before cooking for the first time, carefully wash
the oven accessories.
Before first use, the oven should be heated without food.
During this time, an unpleasant odour may be emitted.
This is quite normal.
•
Set the time of day with the electronic
programmer (see paragraph "How to set the
time of day").
)
•
Switch the oven function control knob to
conventional cooking
and select 250 °C
with the time/temperature control knob.
Open a window for ventilation.
•
•
Allow the oven to run empty for approximately
45 minutes.
This procedure should be repeated with the pizza oven
function and full grill function for approximately
5-10 minutes.
Once this operation is carried out, let the oven
cool down, then clean the oven cavity with a
soft cloth soaked in warm water to which a little
mild washing-up liquid has been added.
Using the ceramic hob for the
first time
The cooking surface should be cleaned before use to
remove any traces of the production process.
Wipe the ceramic surface and frame with a damp
)
cloth using warm water to which a little washing
up liquid has been added, and wipe dry.
Heating up for the first time
To check the cooking zones, briefly switch each
one on.
)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the Oven
“Minute minder” function
The minute minder function can also be used when
the oven is off.
The minute minder alarm will sound at the end of
a timed period, but THE OVEN WILL REMAIN
ON, if it is in use.
To set the minute minder:
1. Press button “Time” to select the “Minute Minder”
function. The relevant indicator will start flashing and
the display will show “0.00”.
2. Turn the time/temperature control knob to
until
the relevant indicator flashes (maximum: 99 minutes).
3. After the setting is carried out, wait for 5 seconds.
The display will revert to the time of day and the mi-
nute minder will start the countdown.
4. At the end of the timed period, an acoustic alarm will
be heard. To switch off the acoustic alarm, press any
button.
To change the minute minder:
1. Press button “Time” to select the “Minute Minder”
function. The relevant indicator will flash.
2. Turn the time/temperature control knob to
or
to change the minute minder setting.After 5 seconds
the indicator will go out and the display will revert to
the time of day.
To cancel the minute minder:
1. Press button “Time” to select the “Minute Minder”
function. The relevant indicator will flash and the
display will show the remaining time.
2. Turn the time/temperature control knob to
until
the display shows “0.00”.After 5 seconds the indicator
will go out and the display will revert to the time of
day.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
How to make the oven switch
off automatically
This function allows the oven to automatically switch off
at the end of a programmed cooking duration time.
Place food in the oven, select a cooking function and
adjust the cooking temperature (see paragraph “How to
select a cooking function and set the temperature”).
Press button “Time” to select the “Cook Time” function.
The relevant indicator will start flashing and the display
will show "0.00". Then, proceed as follows:
To set the duration time:
1. Turn the time/temperature control knob to
and
select the required time while the relevant indicator
flashes (maximum time: 9 hours 59 minutes).
2. After the setting is carried out, wait for 5 seconds.
The display will show the set temperature.
Press button “Time” to display the cooking time.
3. When cooking time is over, the oven will be switched
off automatically and an acoustic alarm will be heard
and the relevant indicator will start flashing. The
display shows “0.00”.
4. To switch off the acoustic alarm, turn the oven function
control knob to the “OFF” position (0).
If you press a button other than the knob, the alarm
will switch off and the display will show “--- °C”. This
means that the oven cannot be operated.
Turn the oven control knob to the “OFF” position (0)
to reset the oven.
The display will revert to the time of day.
To change the duration time:
1. Press button “Time” to select the “Cook Time”
function. The relevant indicator will flash.
2. Turn the time/temperature control knob to
or
to change the cooking duration.
To cancel the duration time:
1. Press button “Time” to select the “Cook Time”
function. The relevant indicator will flash and the
display will show the remaining cooking time.
2. Turn the time/temperature control knob to
until
the display shows “0.00”.After 5 seconds the indicator
will go out and the display will revert to the time of
day.
It is not possible to set the “Cook Time” function
when the oven is off.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to make the oven switch
on and off automatically
The functions “Cook Time” and “End time” can be used
simultaneously to set the oven to switch on and off
automatically at a later time.
1. Set the duration time with the “Cook Time” function
(carry out the cooking duration setting as described
in the previous chapter). Then, press button “Time”:
the display will show the programmed setting.
2. Press button “Time” repeatedly to select the “End
Time” function. The relevant indicator will flash.
3. Turn the time/temperature control knob to
to set
the end of cooking time.
4. After the setting is carried out, wait for 5 seconds.
The relevant indicators will come on and the display
will show the set temperature. The oven will switch
on and off according to the set programmes and an
acoustic alarm will be heard when cooking time is
over.
5. To switch off the acoustic alarm, turn the oven function
control knob to the “OFF” position (0).
If you press a button other than the knob, the alarm
will switch off and the display will show “--- °C”. This
means that the oven cannot be operated.
Turn the oven control knob to the “OFF” position (0)
to reset the oven.
The display will revert to the time of day.
Once you have programmed the oven, you can
check both the cooking duration and end of
cooking time by pressing the “Time” button.
Set the “Cook Time” function to zero to cancel
the programme.
It is not possible to set the “Cook Time” and “End
Time” functions when the oven is off.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Energy saving functions
Safety Cut-Off Function
The oven will switch off automatically if any change of
setting is made, according to the table below (Fig. 14).
If temperature setting is: the oven will switch off:
250°C
after 1 1/2 hours
after 5,5 hours
after 8,5 hours
after 12,5 hours
from 200 up to 245°C
from 120 up to 195°C
less than 120°C
Child Safety Function
To avoid children switching on the oven, it is possible
to lock the oven controls.
The child safety function can be selected only
if no other function has been set.
1. Turn the time/temperature control knob to
and
hold it in the turned position.
2. At the same time, press button “Time” and keep it
pressed for about 3 seconds. The indication ‘SAFE’
will appear in the display (Fig. 15).
After a few seconds, the display will revert to the time
of day.
The oven is now locked. Neither oven functions nor
temperatures can be selected.
To unlock the oven:
1. Turn the time/temperature control knob to
and
hold it in the turned position.
2. At the same time, press button “Time” and keep it
pressed for about 3 seconds. The indication ‘SAFE’
will go off.
The oven can now be operated.
How to switch off the display
The display can be switched off only if no other
function has been set.
To activate this function, proceed as follows:
1. Turn the time/temperature control knob to
and
hold it in the turned position.
2. At the same time, press button “Time” and keep it
pressed for about 3 seconds.
The display will switch off.
To switch on the display:
1. Turn the time/temperature control knob to
and
hold it in the turned position.
2. At the same time, press button “Time” and keep it
pressed for about 3 seconds.
The display will switch on.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Oven
Always cook with the oven door closed.
Stand clear when opening the drop down oven
door. Do not allow it to fall open - support the
door using the door handle, until it is fully
open.
The heating elements do not work when the oven
door is not completely closed.
4
3
2
1
The oven has four shelf levels, and is supplied with
two shelves.
The shelf positions are counted from the bottom
of the oven as shown in the diagram.
It is important that these shelves are correctly
positioned as shown in the diagram.
•
Warning!-Donotplaceobjectsonthebottom
of the oven and do not cover it with aluminium
foil while cooking, as you can damage the
enamelled surfaces and the food you are
cooking. Always place pans, heat-resisting
pansandaluminiumfoilsontheovenshelves.
Warning! - Be careful when you insert and
extract the grid and the dripping pan from the
oven in order not to damage the enamelled
surfaces of the oven cavity.
•
Hints and Tips
Condensation and Steam
The effects of dishes
on cooking results
Dishes and tins vary in their thickness, conductivity,
colour, etc. which affects the way they transmit heat to
the food inside them.
When food is heated it produces steam in the same way
as a boiling kettle. The oven vents allow some of this
steam to escape. However, always stand back from
the oven when opening the oven door to allow any
build up of steam or heat to release.
If the steam comes into contact with a cool surface on
the outside of the oven, e.g. a trim, it will condense and
produce water droplets. This is quite normal and is not a
fault with the oven.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
A Aluminium, earthenware, oven glassware and bright
shiny utensils reduce cooking and base browning.
B Enamelled cast iron, anodized aluminium, aluminium
with non-stick interior and coloured exterior and dark,
heavy utensils increase cooking and base browning.
Storage Drawer
Cookware
Thestoragedrawerislocatedunderneaththeovencavity.
•
Use any oven proof cookware which will withstand
temperaturesof250°C.
During cooking the storage drawer may become
hot if the oven is on high for a long period of time,
thereforeflammablematerialssuchasovengloves,
tea towels, plastic aprons etc. should not be
stored in the drawer.
•
Baking trays, oven dishes, etc. should not be placed
directly against the grid covering the fan at the back
of the oven, or placed on the oven base.
•
Do not use baking trays larger than 30 cm x 35 cm
(12 in x 14 in) as they will restrict the circulation of
heat and may affect performance.
Ovenaccessoriessuchasbakingsheets,willalso
becomehot,thereforecareshouldbetakenwhen
removing these items from the drawer whilst the
oven is in use or still hot.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Conventional Oven
When using this setting, heat comes from both the top
and bottom elements. This allows you to cook on a single
level and is particularly suitable for dishes which require
extra base browning such as pizzas, quiches and flans.
Gratins, lasagnes and hotpots which require extra top
browning also cook well in the conventional oven. This
form of cooking gives you the opportunity to cook without
the fan in operation.
How to Use the
)
Conventional Oven
1. Turn the oven function control knob to the required
cooking function ( ).
2. If necessary, turn the Time/Temperature control knob
to
or
to adjust the temperature.
Top oven element only
This function is suitable for finishing cooked dishes, e.g.
lasagne, shepherds pie, cauliflower cheese etc.
Hints and Tips
The middle shelf position allows for the best heat
distribution. To increase base browning simply lower the
shelf position. To increase top browning, raise the shelf
position.
The material and finish of the baking trays and dishes
used will affect base browning. Enamelware, dark, heavy
or non-stick utensils increase base browning, while oven
glassware, shiny aluminium or polished steel trays reflect
the heat away and give less base browning.
Always place dishes centrally on the shelf to ensure even
browning.
Stand dishes on suitably sized baking trays to prevent
spillage onto the base of the oven and make cleaning
easier.
Do not place dishes, tins or baking trays directly on the
oven base as it becomes very hot and damage will occur.
For faster preheating use the fan oven function to preheat
the oven until the oven indicator neon goes out, then
swich the selector to the conventional oven setting.
Single level cooking gives best results. If you
require more than one level cooking use the fan
oven function.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooking Chart - Conventional Oven
These charts are intended as a guide only. It may be necessary to increase or decrease the temperature to suit your
individual requirements. Only experience will enable you to determine the correct setting for your personal requirements.
Shelf
Temperature Cooking time
Type of dish
position
°C
in minutes
Notes
4
3
2
1
CAKES
Whisked recipes
2
2
1
1
170
170
160
180
45 ~ 60
20 ~ 30
60 ~ 80
40 ~ 60
In cake mould
In cake mould
In cake mould
In cake mould
Shortbread dough
Butter-milk cheese cake
Apple cake
Strudel
Jam-tart
Fruit cake
2
2
1
175
175
175
60 ~ 80
30 ~ 40
45 ~ 60
In bread tin
Sponge cake
Christmas cake
Plum cake
Small cakes
Biscuits
Meringues
Buns
Pastry: Choux
1
1
1
2
2
2
2
2
175
170
170
175
160
100
190
200
30 ~ 40
40 ~ 60
50 ~ 60
25 ~ 35
20 ~ 30
90 ~ 120
12 ~ 20
15 ~ 25
In cake mould
In cake mould
In bread pan
In baking tray
In baking tray
In baking tray
In baking tray
In baking tray
BREAD AND PIZZA
1000 White bread
1
1
2
1
190
190
200
210
40 ~ 60
30 ~ 45
20 ~ 35
15 ~ 30
1-2 pieces
In bread tin
6-8 rolls
500 Rye bread
500 Bread rolls
250 Pizza
on baking tray
FLANS
Pasta flan
2
2
1
2
2
200
200
200
180
200
40 ~ 50
45 ~ 60
35 ~ 45
45 ~ 60
40 ~ 55
in mould
in mould
in mould
in mould
in mould
Vegetable flan
Quiches
Lasagne
Cannelloni
MEAT
1000 Beef
2
2
2
190
180
190
50 ~ 70
100 ~ 130
90 ~ 120
On grid
On grid
On grid
1200 Pork
1000 Veal
1500 English roast beef
1500
underdone
2
2
2
210
210
210
50 ~ 60
60 ~ 70
70 ~ 80
On grid
On grid
On grid
1500 done
1500 well done
2000 Shoulder of pork
1200 Shin of pork
1200 Lamb
2
2
2
2
2
2
2
2
180
180
190
190
180
175
175
190
120 ~ 150
100 ~ 120
110 ~ 130
60 ~ 80
210 ~ 240
120 ~ 150
150 ~ 200
60 ~ 80
with rind
2 pieces
Leg
1000 Chicken
4000 Turkey
Whole
Whole
1500 Duck
Whole
3000 Goose
Whole
1200 Rabbit
Cut in pieces
1500 Hare
2
190
150 ~ 200
Cut in pieces
800 Pheasant
Meat loaf
2
2
190
180
90 ~ 120
40 ~ 60
Whole
In bread pan
FISH
1200 Trout/Sea bream
2
2
190
190
30 ~ 40
25 ~ 35
3-4 fishes
4-6 fillets
1500 Tuna fish/Salmon
Cooking times in the tables do not include pre-heating. We recommend, especially when cooking cakes, pizza and bread, to pre-heat
the oven for about 10 minutes before cooking.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Pizza Oven
The bottom element provides direct heat to the base of
pizzas, quiches or pies, while the fan ensures air is
circulated to cook the pizza toppings or pie fillings.
To obtain the best results use the lower shelf levels.
1. Turn the oven function control knob to the required
cooking function (
2. If necessary, turn theTime/Temperature control knob
to or to adjust the temperature.
).
Pizza Oven
Cooking
time
Pizza function
4
NOTES
TYPE OF DISH
3
2
1
Level
temp. °C
minutes
15 ~ 25
700 Pizza, large
1
200
on baking tray
500 Pizza, small
500 Flat cake
1
1
200
200
10 ~ 20
15 ~ 25
on baking tray or on grid
on baking tray
Cooking times in the table do not include pre-heating. We recommend to pre-heat the oven for
about 10 minutes before cooking.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Grilling
Grilling must be carried out with the oven door
Hints and Tips
closed. The grill pan handles must be removed
from the pan.
-
-
Most foods should be placed on the grid in the grill
pan to allow maximum circulation of air to lift the food
out of the fats and juices. Food such as fish, liver and
kidneys may be placed directly on the grill pan, if
preferred.
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish lightly
with a little oil or melted butter to keep them moist
during cooking.
Accompaniments such as tomatoes and mushrooms
may be placed underneath the grid when grilling meats
When toasting bread, we suggest that the top runner
position is used.
The food should be turned over during cooking, as
required.
The grill cavity becomes very hot during use.
Caution must be used when removing and
replacing the grill pan handles. If necessary
oven gloves should be used to protect the
hands.
How to Use the Full Grill
)
-
-
-
1. Turn the oven function control knob to the required
cooking function ( ).
2. If necessary, turn the Time/Temperature control knob
to
or
to adjust the temperature.
3. Adjust the grid and grill pan runner position to allow
for different thicknesses of food. Position the food
close to the element for faster cooking and further
away for more gentle cooking.
During cooking, the grill cycles on and off to
prevent overheating.
How to Use the Inner Grill
The grill provides quick direct heat to the central area of
the grill pan. Use the inner grill element for cooking small
quantities, it can help to save energy.
Preheat the grill on a full setting for a few minutes before
sealing steaks or toasting. Adjust the heat setting and
the shelf as necessary during cooking.
)
During cooking, the cooling fan will operate.
1. Turn the oven function control knob to the required
cooking function ( ).
2. If necessary, turn the Time/Temperature control knob
to
or
to adjust the temperature.
4. Adjust the heat setting and the shelf as necessary,
for different thicknesses of food and follow the
instructions for grilling.
O
L
I
Grilling
-
Cooking time
(minutes)
Grilling
Quantity
TYPE OF DISH
4
3
2
1
Lower
side
Upper
side
Pieces Weight
temp.
Level
°C
Fillet steaks
Beef-steaks
Sausages
Pork chops
Chicken (cut in two)
Kebabs
Chicken (breast)
Hamburger
Fish (fillets)
Sandwiches
Toast
4
4
8
4
2
4
4
6
4
800
600
—
600
1000
—
400
600
400
—
3
3
3
3
3
3
3
3
3
3
3
max
max
12 ~ 15
10 ~ 12
12 ~ 15
12 ~ 16
30 ~ 35
10 ~ 15
12 ~ 15
10 ~ 15
12 ~ 14
3 ~ 7
12 ~ 14
6 ~ 8
max
max
max
max
max
max
max
max
max
10 ~ 12
12 ~ 14
25 ~ 30
10 ~ 12
12 ~ 14
8 ~ 10
10 ~ 12
—
4-6
4-6
—
2 ~ 4
2 ~ 3
The chart is intended as a guide only and should be adjusted according to taste.
Cooking time depends on the thickness of the meat and not on its weight.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Defrosting
The oven fan operates without heat and circulates the
air, at room temperature, inside the oven. This increases
the speed of defrosting. However, please note that the
temperature of the kitchen will influence the speed of
defrosting.
This function is particularly suitable for delicate food which
could be damaged by heat, e.g. cream filled gateaux,
iced cakes, pastries, bread and other yeast products.
How to Use Defrosting
)
Turn the oven function control knob to
.
Hints and Tips
•
•
•
Cover food with a lid, aluminium foil or plastic film to
preventdryingoutduringdefrosting.
ALWAYS COOK THOROUGHLY IMMEDIATELY
AFTERTHAWING.
Frozen food should be placed in a single layer when
ever possible and turned over half way through the
defrostingprocess.
•
Only joints of meat and poultry up to 2 kg. (4 lb.) are
suitable for defrosting in this way.
Refer to the following table for approximate defrosting
times.
Defrosting Chart
Standing time
Defrostingtime
(Mins)
Food
Notes
(Mins)
Chicken 1000 g.
100-140
20-30
Place the chicken on an inverted saucer on a large
plate. Defrost open and turn at half time or defrost
coveredwithfoil.Removegibletsassoonaspossible.
Meat 1000 g.
100-140
90-120
23-35
20-30
20-30
10-15
10-20
10-15
10-15
Defrost open and turn at half time or cover with foil
Meat 500 g.
Asabove
Trout 150 g.
Defrostopen
Defrostopen
Defrostopen
Strawberries300g.
Butter 250 g.
30-40
30-40
Cream 2 x 200 g.
80-100
Defrost open (cream is easy to whip even if parts of
it are still slightly frozen)
Cake 1400 g.
60
60
Defrostopen
The times quoted in the chart should be used as a guide only, as the speed of defrosting will depend on the kitchen
temperature. For example, the colder the ambient temperature, the longer the defrosting time.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Before any maintenance or cleaning can be carried
out, you must DISCONNECT the cooker from the
electricity supply.
This appliance cannot be cleaned with steam or
with a steam cleaning machine.
The Hob Top
The hob is best cleaned whilst it is still warm, as spillage
can be removed more easily than if it is left to cool.
Regularly wipe over the hob top using a soft cloth well
wrung out in warm water to which a little wasing up liquid
has been added.Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.
Pan Supports
The hob has cast iron pan supports. Take care when
removing them. They are fairly heavy and could damage
the hob or your kitchen furniture if you let them fall down.
Wash the pan supports using hot soapy water.
If necessary, a paste cleaner or a soap impregnated steel
wood pad can be used with caution.
The Burners
The burner caps and crowns can be removed for cleaning.
Wash the burner caps and crowns using hot soapy water,
and remove marks with a mild paste cleaner. A well
moistened soap impregnated steel wool pad can be used
with caution, if the marks are particularly difficult to remove.
After cleaning, be sure to wipe dry with a soft cloth.
Ignition electrode
The electric ignition is obtained through a ceramic and
metal electrode (see diagram page 5 - letter C). Keep
these components very clean, to avoid lighting difficulties,
and check that the burner crown holes are not
obstructed.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Oven
The oven should be kept clean at all times. A
build-up of fats or other foodstuffs could result in
a fire, especially in the grill pan.
Pyrolytic cleaning
Theovencavityiscoatedwithaspecialenamelresistant
tohightemperatures.
During the pyrolytic cleaning process, the temperature
insidetheovencanreachabout500°Cthusburningfood
residuals.
For your security, during the pyrolityc cleaning process,
theovendoorautomaticallylockswhenthetemperature
inside the oven approaches about 300 °C.
The door remains locked during the cleaning operation
until the end of the pyrolytic cleaning function.
Aftertheovencavityhascooleddown,thedoorunlocks.
The cooling fan operates during cooking until the oven
has cooled down. After each cooking, it is advisable to
remove all the food residuals with a wet sponge.
Cleaning materials
Before using any cleaning materials on your oven, check
that they are suitable and that their use is recommended
by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives should
also be avoided.
•
Never use steam or steam machines to clean the
appliance.
External cleaning
However, from time to time, it will be necessary to do a
morecompleteandthoroughcleaning,usingthepyrolytic
cleaning function. You can select two different levels of
pyrolytic cleaning depending on how dirty the oven is.
Regularly wipe over the control panel, oven door and door
seal using a soft cloth well wrung out in warm water to
which a little washing up liquid has been added.
To prevent damaging or weakening the door glass
panels avoid the use of the following:
Iftheovencavityisnotverydirty,werecommendtoselect
thepyrolytic1function(PYrI)ontheprogrammerdisplay.
•
•
Household detergent and bleaches
Impregnated pads unsuitable for non-stick
saucepans
It is advisable to wipe the oven over with a soft sponge
soakedinwarmwateraftereachpyrolyticcleaningcycle
is carried out.
•
•
•
•
Brillo/Ajax pads or steel wool pads
Chemical oven pads or aerosols
Rust removers
Iftheovencavityisverydirty,weadviseyoutoselectthe
pyrolytic 2 function (PYr 2) on the programmer display.
Bath/Sink stain removers
Duringthepyrolyticcleaningfunction, itisnotpossibleto
usetheovenfor2hourswhenselectingthePYrIfunction
and up to 2 hours and a half when the PYr 2 function is
active.
Clean the outer and inner door glass using warm soapy
water.Shouldtheinnerdoorglassbecomeheavilysoiled
it is recommended that a cleaning product such as Hob
Brite, or Bar Keepers Friend is used.
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not
observed the glass panel may shatter.
If the door glass panel becomes chipped or has
deep scratches, the glass will be weakened and
must be replaced to prevent the possibility of the
panel shattering. Contact your local Service Centre
who will be pleased to advise further.
Models in stainless steel or aluminium:
We recommend to clean the oven door using only a wet
sponge and dry it up after cleaning with a soft cloth.
Never use steel wool, acids or abrasive products as they
can damage the oven surface.
Clean the oven control panel following the same
precautions.
Oven Shelves
To clean the oven shelves, soak in warm soapy water
and remove stubborn marks with a well wetted soap
impregnated pad. Rinse well and dry with a soft cloth.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the pyrolytic clean-
ing function
Before activating the pyrolytic cleaning function,
remove any excessive spillage and make sure
that the oven is empty. Do not leave anything
inside it (e.g. pans, grids, baking tray, drippin pan)
as this could severely damage them.
Ensure that the oven door is closed before
activating the pyrolytic cleaning function.
When the pyrolytic cleaning function is on, it is
advisable not to use the hob as this could cause
overheating and damage the appliance.
During the pyrolytic cleaning cycle the oven door
becomes hot. Children should be KEPT AWAY
until it has cooled.
Choose this function to clean the oven by pyrolysis.
The following pyro levels are available:
Pyrolytic 1 (PYr I) time : 2 h = 30 min heat-up +1 h at
480°C + 30 min cooling down.
Pyrolytic 2 (PYr 2) time : 2 h 30 min. = 30 min heat-up
+1 h 30 min at 480°C + 30 min cooling down.
The pyrolytic cleaning cycle duration/time cannot
be changed.
1. Turn the oven knob to position
. The “Cook Time”
indicator and the PYr I indication will flash in the dis-
play (Fig. 22).
2. Press “Pyrolytic” button to activate the pyrolytic
cleaning function. The temperature indicators will start
lightning alternatively. This means that the oven is
rapidly heating up.
The “PYr I” indication will stop to flash, the oven light
will go out and the pyrolytic cleaning cycle will start
(Fig. 24).
Iftheovencavityisverydirty,weadviseyoutoselectthe
pyrolytic 2 function (PYr 2) on the programmer display.
1. Press “Pyrolytic” button to select the pyrolytic 2 (PYr
2) function.
Press button “Time” to display the remaining time.
After some time, the temperature level indicators will light
permanently in the display. This means that the oven
door has been locked.
At the end of the pyrolitic cleaning process, “0.00” will
flash in the display.
Once the oven has cooled down (check the temperature
level indicators coming off one by one), the oven door
will unlock.
To reset the oven, turn the oven function control knob to
the “OFF” position (0).
If you press a button other than the knob, the alarm will
switch off and the display will show “--- °C”. This means
that the oven cannot be operated.
To reset the oven, turn the oven function control knob to
the “OFF” position (0).
To stop the pyrolytic cleaning cycle at any time, turn the
oven function control knob to the “OFF” position (0).
NOTE: The time indication is comprehensive of the cool
ing down time.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
If you turn the oven knob to a cooking function while
the pyrolytic function is active, the cleaning cy-
cle will be interrupted.
If the oven door lock is activated, it is impossible to
select any cooking until the door lock is off.
To programme the pyrolytic
cleaning cycle (delayed start,
automatic stop)
If you wish, you can programme the starting and end-
ing time of the pyrolytic cleaning cycle.
1. Turn the oven knob to position
. The “Cook
Time” indicator and the PYr I indication will flash in
the display (Fig. 22).
2. Press “Pyrolytic” button to activate the pyrolytic
cleaning function. The temperature indicators will
start lightning alternatively. This means that the
oven is rapidly heating up.
The“PYr I” indication will stop to flash, the oven light
goes out and the pyrolytic cleaning cycle starts
(Fig. 24).
Iftheovencavityisalotdirty, weadviseyoutoselectthe
pyrolytic 2 function (PYr 2) on the programmer display.
1. Press “Pyrolytic” button to select the pyrolytic 2
(PYr 2) function.
2. Press button “Time” twice to display the end time of
the cleaning cycle. After the setting is carried out,
the “Cook Time” and “End Time” indicators will light
permanently.
3. Turn the time/temperature control knob to
to
select the the end time of the cleaning cycle.
The pyrolytic cleaning cycle will start according to the
programmed time. The temperature level indicators will
light up alternatively. This means that the oven is rapidly
heating up.
After some time, the temperature level indicators will
light permanently in the display. This means that
the oven door has been locked.
At the end of the pyrolitic cleaning process, “0.00” will
flash in the display.
Once the oven has cooled down (check the tempera-
ture level indicators coming off one by one), the
oven door will unlock.
To reset the oven, turn the oven function control knob to
the “OFF” position (0).
If you press a button other than the knob, the alarm will
switch off and the display will show “--- °C”. This means
that the oven cannot be operated.
To reset the oven, turn the oven function control knob to
the “OFF” position (0).
To stop the pyrolytic cleaning cycle at any time, turn
the oven function control knob to the “OFF” position
(0).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning The Oven Door
The oven door is made up of four glasses.
It is possible to remove them for easier cleaning.
Warning - The oven door may bang shut if you try
to extract the inner glasses when the oven door
is still fitted to the oven.
Before cleaning the oven door, we recommend you to
removeitfromtheoven.
Proceed as follows:
1. open the oven door completely and locate the two
2. unlockandturnthesmallleverslocatedonthetwo
hinges which link the door to the oven;
hinges;
3. handle the door by its left- and right-hand sides,
then slowly turn it towards the oven until it is half-
closed;atthispoint,gentlypulltheovendooraway
fromtheovenframe;
4. placetheovendooronasolidsurface,beingcareful
to avoid the glass becoming scratched. Then
remove the two screws located on the sides of the
ovendoor;
5. extract the inner glass support;
6. gentlyextractthethreeinnerglasses,startingwith
the uppermost one first.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleantheovendoorglasswithwarmwaterandasoftcloth
only. Never use harsh abrasives as they could damage
the special heat-resistant surface of the inner glasses.
Once the cleaning is carried out, refit the oven door,
followingtheprocedureinreverse.
7.
The two glasses in the middle are special glasses
that have been treated to resist heat. They are
marked with a small dot located on a corner and a
black frame respectively.
It is important that, when refitting the oven door,
the inner glasses are fixed in the right position.
To check if this operation has been carried out
correctly, when inserting the glass, make sure that
the surface of the glass marked with a black frame
looks downwards and that the dot is located on the
upper left corner of the glass (see diagram 7).
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not observed
the glass panels may shatter.
If the door glass panels become chipped or have
deep scratches, the glasses will be weakened and
must be replaced to prevent the possibility of the
panel shattering. Contact your local Service Force
Centre who will be pleased to advise further.
Oven lamp replacement
Disconnect the appliance from the electricity
supply.
If the oven bulb needs replacing, it must comply with
the following specifications: electric power, 40 W; electric
rate, 230 V (50 Hz); resistant to temperatures of 300°C;
connection type: E14. These bulbs are available from
your local Service Force Centre.
To replace the faulty bulb:
)
1. Ensure the oven is disconnected from the electrical
supply.
2. Turn the glass cover anticlockwise.
3. Remove the faulty bulb and replace it with the new
one.
4. Refit the glass cover.
5. Reconnect to the electrical supply.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Something not working
If the appliance is not working correctly, please carry out the following checks, before contacting your local Service
Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,
a charge will be made even if the appliance is under guarantee.
SYMPTOM
SOLUTION
Check that the unit is plugged in and the electrical
supply is switched on
ƒ There is no spark when lighting the gas
Check that the RCCB has not tripped (if fitted)
Check the mains fuse has not blown
Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
ƒ The gas ring burns unevenly
Check the main jet is not blocked and the burner
crown is clear of food particles.
Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
Check that a cooking function has been selected.
Check the oven is in manual operation.
ƒ The oven does not come on.
Check that the socket switch or the switch from the
mains supply to the cooker are ON.
ƒ The oven light does not come on.
Select a function with the oven function control
knob.
Check the light bulb, and replace it if necessary
(see "Oven Lamp replacement").
ƒ It takes too long to finish the dishes, or they are
The temperature may need adjusting.
cooked too fast.
ƒ Steam and condensation settle on the food and the
Refer to the contents of this booklet, especially to
the chapter “Using the Oven”.
oven cavity.
Leave dishes inside the oven no longer than 15-20
minutes after the cooking is completed.
Check that shelves and bakeware are not vibrating
ƒ The oven fan is noisy.
in contact with the oven back panel.
ƒ The display shows "12.00".
Set the time of day (see chapter "How to set the
time of day").
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Service and Spare Parts
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:
For Customer Service in the Republic of Ireland please
contact us at the address below:
Zanussi-Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
Tel: +353 (0) 1 4090 751
Email: [email protected]
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not Work-
ing.”
When you contact the Service Force Centre you will need
to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or
guarantee documentation is required for in-
guarantee service calls.
Customer Care Department
For general enquiries concerning your Zanussi-Electrolux
appliance or for further information on Zanussi-Electrolux
products, please contact our Customer Care Department
by letter or telephone at the address below or visit our
Customer Care Department
Zanussi-Electrolux
Cornwall House
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
* calls to this number may be recorded for training
purposes.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee Conditions
Zanussi-Electrolux Guarantee
conditions
European Guarantee
If you should move to another country within Europe then
your guarantee moves with you to your new home
subject to the following qualifications:
We, Zanussi-Electrolux, undertake that if, within 24
months of the date of the purchase, this Zanussi-
Electrolux appliance or any part thereof is proved to be
defective by any reason only of faulty workmanship or
materials, we will, at our option, repair or replace the
same FREE OF ANY CHARGE for labour, materials or
carriage on condition that:
*
The guarantee starts from the date you first
purchased your product.
*
The guarantee is for the same period and to the same
extent for labour and parts as exist in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be
transferred to another user.
Your new home is within the European Community
(EC) or European Free Trade Area.
The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
*
*
*
*
*
*
The appliance has been correctly installed and used
only on the gas and electricity supply stated on the
rating plate.
The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any person
not authorised by us.
*
The product is installed taking into account
regulations in your new country.
*
*
*
All service work under this guarantee must be
undertaken by a Zanussi-Electrolux Service Centre.
Any appliance or defective part replaced shall become
the Company's property.
This guarantee is in addition to your statutory and
other legal rights.
Before you move, please contact your nearest Customer
Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after
you and your appliances.
France
Germany
Italy
Sweden
UK
Senlis
Nürnberg
Pordenone +39 (0)1678 47053
Stockholm +46 (0)8 738 79 50
+33 (0)3 44 62 29 99
+49 (0)911 323 2600
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours, in which case a premium will be charged.
Slough
+44 (0)1753 219897
Exclusions
This guarantee does not cover:
*
*
*
*
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
Appliances found to be in use within a commercial or
similar environment, plus those which are the subject
to rental agreements.
Products of Electrolux-Zanussi manufacture which
are not marketed by Electrolux.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for the Installer
Technical Data
Oven
Top heating element
Bottom heating element
Ovenelement
800 W
1,000 W
1,800 W
Appliance Class 2 sub class 1 and Class 1
APPLIANCE CATEGORY:
APPLIANCE GAS SUPPLY:
II2H3+
Natural Gas 20 mbar
Grill Element (inner)
Grill Element (full)
Pizza Oven
1,650 W
2,450 W
3,000 W
2,000 W
2,450 W
30 W
Dimensions
Height
900 mm
600 mm
Depth
Width
600 mm
Convection heating element
Pyrolytic cleaning function
Convection fan
Oven Capacity
56 litres / 1.97 Cu. ft
Hob
Oven light
40 W
Rear left burner (semi-rapid)
2,0 kW
Total rating
3,100 W
230 V
Front left burner (ultra-rapid triple crown)
Rear right burner (semi-rapid)
4,0 kW
2,0 kW
1,0 kW
Supply voltage (50 Hz)
Front right burner (auxiliary)
BURNER
ULTRARAPID
(large)
SEMI-RAPID
(medium)
AUXILIARY
(small)
TYPEOF
CHARACTERISTICS
GAS
POSITION
MAX
MIN
MAX
MIN
MAX
MIN
NOMINALTHERMAL
POWER kW
4.0
1.20
2.0
0.45
1.0
0.33
VALUE =
Hs 37.78 MJ/m3
Ws 50.72 MJ/ m3
NATURAL
GAS
20 mbar
NOMINALFLOW
RATE m3/h
0.381
146
0.114
0.190
96
0.043
0.095
70
0.031
NOZZLEREFERENCE
1/100 mm
Adjust.
Adjust.
Adjust.
NOMINALTHERMAL
POWERkW
4.0
1.20
2.0
0.45
1.0
0.33
LPG GAS
28-30/37 Hs 49.92 MJ/Kg
mbar
VALUE =
NOMINALFLOW
RATEg/h
288
98
86
56
144
71
32
32
72
50
24
28
Ws 82.09 MJ/ m3
NOZZLEREFERENCE
1/100 mm
Important Safety Requirements
The cooker should not be installed in a bed sitting room
with a volume of less than 20m3, if it is installed in a room
of volume less 5m3 an air vent of effective area of 110cm2
is required; if it is installed in a room of volume between
5m3 and 10m3, an air vent of effective area 50cm2 is
required, while if the volume exceeds 11m3 no air vent is
required. However, if the room has a door which opens
directly to the outside, no air vent is required even when
the volume is between 5m3 and 11m3.
This appliance must be installed in accordance with the
Gas Safety (Installation and Use) Regulations (current
addition) and the I.E.E. Wiring Regulations.
Detailed recommendations are contained in the following
British Standard Codes of Practice - B.S. 6172, B.S.
5440: Part 2 and B.S. 6891: Current Editions.
For appliances installed in the Republic of Ireland please
refer to NSAI- Domestic Gas Installation I.S. 813 Current
Editions and the ETCI Rules for Electrical Installations.
If there are other fuel burning appliances in the same
room, B.S. 5440: Part. 2: Current Editions should be
consulted to determine the requisite air vent
requirements.
Provision for Ventilation
The room containing the cooker should have an air
supply in accordance with B.S. 5440: Part 2: Current
Editions.
For appliances installed in the Republic of Ireland please
refer to the NSAI- Domestic Gas Installation I.S. 813
Current Editions Table Four.
The following requirements for ventilation must be met.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
L.P.G. cookers MUST NOT be installed below ground
level, i.e. in a basement, or aboard any boat, yacht or
other vessel.
For appliances installed in the Republic of Ireland please
refer to NSAI- Domestic Gas Installation I.S 813 Current
Edition Section 7- Permitted Locations ofAppliance.
Location of the appliance
This appliance must not be installed in a bed-sitting room
of volume less than 20m³or in a bathroom, shower room
or garage. It is essential that the appliance is positioned
as stated below (see fig.1) i.e. shelves, wall cabinets
and cooker hoods must be fitted a minimum of 787mm
directly above the top of the hotplate and 400mm above
the hotplate when fitted in line with the outside of the
appliance. If the units are intended to be fitted adjacent
to the appliance but less than 400mm above the hotplate,
then a minimum space of 100mm must be maintained
between the sides of the unit and the appliance (see fig.).
Curtains must not be fitted immediately behind the
appliance or within 150mm of the sides of the hotplate. If
fitted next to or between two base units a minimum space
of 1mm must be left between each unit and the side of
the appliance. The levelling feet fitted to the appliance
will achieve a nominal height to hotplate trims of 900mm
+20mm.
Positioning the Cooker
Caution:
Some soft or badly fitted floor coverings can be damaged
when the cooker is moved across their surface for
cleaning. It is advisable to ensure that the floor covering
in the area below the cooker is either securely fixed so
as not to become damaged when the cooker is moved
or, if preferred, removed.
Installation
Positioning theAppliance (Fig. 1)
D
This appliance cannot be positioned on a
base.
E
The appliance cannot be installed beside or between
furniture units whose height exceeds the cooker worktop.
C
115
Note A:
B
The appliance is designed to be flush fitted with 2mm
clearance at each side to allow for it to be pulled forward
for cleaning etc.
Note B:
The hotplate side trims should be flush with the cabinets
and must not be below. Adjustable levelling feet at the
front and rear are provided on the base of the appliance.
Adjustment is obtained by rotating in or out, the feet at
the front or rear of the appliance from the underside of
the appliance.
A spirit level should be placed on a cake tray on one of
the shelves to confirm that the appliance is correctly
levelled.
A
FO 1141
Fig. 1
The levelling feet fitted to the appliance will achieve a
height to hotplate trims of 900mm-0 + 10.
Note C:
If the appliance is fitted next to a side wall or cabinets
above height of the hotplate trims, then a gap of 115 mm
is required.
Curtains must not be fitted immediately behind the cooker
or within 115 mm of the sides of the cooker.
Note D:
Any wall cabinet or extractor must not be lower than
780mm above hotplate level.
Note E:
Wall cabinets may be fitted in line with the sides of the
base units, providing that the lower edge of the wall cabinet
is a minimum of 420mm above the worktop.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
300 mm.
WALL FACE
BACK OF COOKER
ENGAGEMENT EDGE FOR
STABILITY BRACKET
LEVELLING FEET
BASE OF COOKER
A
PENCIL LINE ON THE FLOOR
295 mm.
SIDE VIEW
OF THE COOKER
PLAN VIEW OF THE COOKER
FO 0179
Fig. 2
Fitting the Stability Bracket
(Not supplied)
If the cooker has to be installed with a flexible supply
pipe, it is necessary that a stability device is fitted.
(See "Important Safety Requirements").
Connecting to Gas
This cooker is designed to be installed with an appliance
flexible connection. Connection is made to the RC 1/2
(1/2" B.S.P.) threaded entry pipe located just below the
hotplate level on the rear right-hand side of the cooker.
Check for gas soundness after connecting the gas supply.
The stability bracket should be fitted by the installer and
these instructions should be read in conjunction with
the leaflet packed with the stability bracket.
The gas bayonet connector must be fitted in the shaded
area indicated in Fig. 3. Take into account that it must
be possible to pull the cooker forward sufficiently. The
hose must not get caught on the stability bracket.
Place cooker in its intended position and level cooker.
Note:
Mark off 295mm (11 1/2") from the right hand side of the
cooker as shown, this is the centre line of the bracket
fixing.
If using different types of gas bayonet connection, it may
not be possible for the appliance to be pushed fully back
to the wall stops.
Draw a line 100mm (4") from the front edge of the levelling
feet (see Fig. 1) and remove cooker from its position.
Mark off 580mm (23") back from this line on the centre
line of the bracket to locate the front edge of the lower
bracket.
Important:
Flexible tubing MUST comply with BS.669 Current
Edition.
Fix lower bracket (with two fixing holes) to the floor, then
measure height from floor level to engagement edge on
back of cooker, dimension 'A' of Fig. 2.
Assemble upper bracket to lower bracket so that
underside of bracket is dimension 'A' +3mm (1/8") above
floor level. Re-position cooker and check that top bracket
engages into cooker back to a depth of 75mm (3"), as
shown in Fig. 2.
600
450
Should the stability bracket currently installed not allow
the cooker to stand correctly, ask the installer to replace
it with the correct type.
130
FO 0180
Fig. 3
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connections
Any electrical work required to install this hob
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
THIS COOKER MUST BE EARTHED.
The manufacturer declines any liability should
these safety measures not be observed.
This cooker is designed to be connected to a
230 V 50 Hz AC electrical supply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the hob rating
plate. The rating plate is located on the bottom of the
hob. A copy is attached on the back cover of this book.
The cooker is supplied with a 3 core flexible supply cord.
The cooker should be connected to a double pole switch
with a minimum gap of 3mm between the switch contacts
and of a type suitable for the required load in compliance
with the current electric regulations. The switch should
be sited within 2m of the hob and be easily accessible
upon completion of the installation.
The switch must not break the yellow and green earth
cable at any point.
NOTE:
The earth wire should be about 2 cm longer than the live
and neutral wires.
Ensure that the hob supply cord does not come
into contact with surfaces with temperatures
higher than 50 deg. C.
Supply Cable Specifications
For Uk use only
Connection Min. size
Cable / flex Fuse
via
Cable/flex type
• Cooker
Control
Circuit
6 mm2
H05 VV-F 30A
For Europe use only
Min. size Cable/flex Cable / flex type Fuse
3x 2.5 mm2
H05 RR-F
30A
H05V2V2-F
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Commissioning
When the hob has been fully installed it will be necessary
to check the minimum flame setting. To do this, follow
the procedure below.
-
-
Turn the gas tap to the MAX position and ignite.
Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
Procedure:
Re-ignite the burner and set to MIN.
Remove the control knob. According to the different
gas tap versions, the adjustment screw can be located
down the centre of the gas tap control shaft or on the
gas tap body istself (see diagram).
)
-
-
-
To adjust, use a thin bladed screwdriver and turn the
adjustment screw until the flame is steady and does
not extinguish, when the knob is turned from MIN to
MAX. Repeat this procedure for all burners.
Position of by-pass screw
(according to different gas
tap versions)
Pressure Testing
Remove left hand pan support and front left burner
)
-
cap and crown.
-
-
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite another burner
supply.
-
-
The pressure reading should be nominally 20mbar
and must be between 17 mbar and 25mbar.
Turn off the burner supplies.
Conversion from Natural Gas to LPG
It is important to note that this model is designed for use
with natural gas but can be converted for use with butane
To adjust the gas rate
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw. Upon
completion, stick the replacement gas type label on the
back plate of the appliance.
or propane gas providing the correct injectors are fitted
and the gas rate is adjusted to suit.
Method
IMPORTANT
•
•
•
Ensure that the gas taps are in the 'OFF' position
Isolate the appliance from the electricity supply
Remove all pan supports, burner caps, rings, crowns
and control knobs.
The replacement/conversion of the appliance should only
be undertaken by a competent person
•
With the aid of a 7mm box spanner, the burner
injectors can then be unscrewed and replaced by the
appropriate LPG injectors (see Technical Data).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
ZCM 650/651
0,79 kWh
0,78 kWh
56
43 min.
41 min.
1130 cm²
35
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER CARE
Zanussi-Electrolux
Cornwall House
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
© Electrolux plc 2004
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and
lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
35687-5421
07/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|