User manual
Dishwasher
ZDTS 101
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety information
• Under no circumstances should you attempt
to repair the machine yourself. Repairs car-
ried out by inexperienced persons will cause
injury or serious malfunctioning. Contact
your local Service Force Centre. Always in-
sist on genuine spare parts.
In the interest of your safety and to ensure the
correct use, before installing and first using the
appliance, read this user manual carefully, in-
cluding its hints and warnings. To avoid
unnecessary mistakes and accidents, it is im-
portant to ensure that all people using the
appliance are thoroughly familiar with its opera-
tion and safety features. Save these instruc-
tions and make sure that they remain with the
appliance if it is moved or sold, so that everyone
using it through its life will be properly informed
on appliance use and safety.
General safety
• Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could en-
danger life! Comply with the safety instruc-
tions of the dishwasher detergent
manufacturer.
Correct use
• Thisdishwasher is only intended forwashing
household utensils suitable for machine
washing.
• The water in your dishwasher is not for drink-
ing. Detergent residues may still be present
in your machine.
• Ensure that the door of the dishwasher is
always closed when it is not being loaded or
unloaded. In this way you will avoid anybody
tripping over the open door and hurting
themselves.
• Do not put any solvents in the dishwasher.
This could cause an explosion.
• Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
• Do not sit or stand on the open door.
Child safety
• This appliance is designed to be operated
by adults. Don’t allow children to use the
dishwasher unsupervised.
• Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
• Avoid opening the door whilst the appliance
is in operation, hot steam may escape.
• Do not take any dishes out of the dishwasher
before the end of the dishwashing cycle.
• Keep all packaging well away from children.
There is risk of suffocation.
• After use, isolate the appliance from the
power supply and turn off the water supply.
• Keep all detergents in a safe place out of
children’s reach.
• This product should be serviced only by an
authorised service engineer, and only genu-
ine spare parts should be used.
• Keep children well away from the
dishwasher when the door is open.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
or if the control panel, work top or plinth area
are damaged such that the inside of the ap-
pliance is freely accessible. Contact your
local Service Force centre, in order to avoid
hazard.
Installation
• Check your dishwasher for any transport
damage. Never connect a damaged ma-
chine. If your dishwasher is damaged con-
tact your supplier.
• All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
• All packaging must be removed before use.
• Any electrical and plumbing work required to
install this appliance must be carried out by
a qualified and competent person.
CAUTION!
For electrical and water connection carefully
follow the instructions given in specific para-
graphs.
• For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
• Never use the dishwasher if the electrical
supply cable and water hoses are damaged;
Control panel
1. On-Off button
2. Programme selection/cancel button
3. Indicator lights
4. Programme lights
4
Download from Www.Somanuals.com. All Manuals Search And Download.
the appliance MUST be in setting mode.
If a programme light is illuminated and End of
programme light is illuminated with fixed light,
the last performed programme is still set.
In this case theprogramme has to becancelled:
Setting mode
The appliance is in setting mode when all
programme lights are off and End of pro-
gramme light flashes.
1. Press and hold the Programme selection/
Cancel button until the light of the running
programme turns off and the End of pro-
gramme light is flashing.
IMPORTANT!
Always remember that when performing opera-
tions such as:
• selecting a washing programme
• setting the water softener
2. Release the Programme selection/Can-
cel button.
• deactivation/activation of the audible signals
Programme selection/cancel button
• Starting the washing programme:
1. Press the On-Off button.
2. Press the Programme selection/cancel button
once, the light of the last performed washing pro-
gramme illuminates and the End of programme
light flashes.
3. Press the Programme selection/cancel button
as many times as necessary to illuminate the light
corresponding to the desired programme.
4. Close the dishwasher’s door, the programme will
start automatically.
IMPORTANT!
Once the programme has started, if you want to
change the selection made you must cancel the wash-
ing programme in progress.
• Cancel the washing programme in progress:
1. Open the door.
2. Press and hold the Programme selection/cancel
button until the light of the running programme
turns off and the End of programme light is flash-
ing.
3. Release the Programme selection/cancel but-
ton.
4. Switch off the machine by pressing the On-Off
button or select a new washing programme (check
that there is detergent in the detergent dispenser.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicator lights
Illuminates when the washing programme has ended.
End of programme indicator light
It also has added functions of visual signalling as:
– the setting of the water softener,
– deactivation/activation of the audible signals,
– intervention of an alarm due to the malfunction of
the machine.
Salt indicator light
Illuminates when the special salt has run out.
Is never illuminated while a washing programme is
running.
Audible signals
Audible signals have been introduced to help indicate Factory setting: audible signals activated.
which operations the dishwasher is performing.
– end of the washing programme,
– malfunction of the appliance
It is possible to deactivate the audible signals,
flashes and programme light B illuminates
using the Programme selection/Cancel but-
with fixed light.
ton.
3. Press Programme selection/Cancel but-
ton again: programme light A becomes
fixedandprogrammelightBstartsflashing.
Deactivation/activation of the audible sig-
nals
1. Press the On/Off button. The appliance
must be in setting mode.
4. After a few seconds:
– programme light A turns off
– programme light B goes on flashing
2. Press and hold Programme selection/
Cancel button until programme light A
6
Download from Www.Somanuals.com. All Manuals Search And Download.
– End of programme light illuminates
with fixed light, indicating that the audi-
ble signals are active.
6. To memorise the operation, switch off the
dishwasher.
7. To activate again the audible signals, sim-
ply follow the above operations until the
End of programme indicator light illumi-
nates.
5. To deactivate the audible signals press
again the Programme selection/Cancel
button: the End of programme light turns
off indicating that the audible signals have
been deactivated.
Washing programmes
Programme
Intensive 65°
Degree of soil
Heavy soil
Type of load
Programme description
Crockery, cutlery, pots
and pans
Prewash
Main wash
2 intermediate rinses
Final rinse
Drying
Normal 65°
Normal soil
Crockery, cutlery, pots
and pans
Prewash
Main wash
2 intermediate rinses
Final rinse
Drying
65° A 30'
Light soil
Crockery and cutlery
Crockery and cutlery
Main wash
Final rinse
1)
Normal soil
Prewash
Main wash
1 intermediate rinse
Final rinse
Drying
50°
2)
Rinse and Hold
Any.
1 cold rinse (to avoid food
scraps from sticking
together).
Partial load (to be completed later in the day).
This programme does not
require the use of deter-
gent.
1) Ideal for washing a partially loaded dishwasher. This is perfect daily programme, made to meet the needs of a family of 4
persons who only wish to load breakfast and dinner crockery and cutlery.
2) Test programme for test institutes.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
First use
– Set the water hardness to level 1.
Before using your dishwasher for the first time:
IMPORTANT!
• Ensure that the electrical and water connec-
tions comply with the installation instructions
If the drying results are not satisfactory we rec-
ommend that you:
• Remove all packaging from inside the appli-
ance
1. Fill up the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
• Set the water softener
• Pour 1 litre of water inside the salt container
and then fill with dishwasher salt
If you decide in future to use separated deter-
gents, we advise that you:
• Fill the rinse aid dispenser
When using tablets that integrate rinse aid
and detergent:
– Fill up the salt and rinse aid container.
– Adjust the water hardness setting to the
highest level and perform 1 normal washing
programme without loading any dishes.
there is no need to fill up with rinse aid
– set the water softener
– Adjust the water hardness setting according
to the hardness of the water in your area.
– add special (dishwasher) salt
When using tablets that integrate rinse aid,
detergent, salt function and other additives:
there is no need to fill up with special salt or
rinse aid.
– Adjust the rinse aid dosage
Check whether these detergents are suitable
for your water hardness. Follow the manufac-
turers instructions.
Set the water softener
The dishwasher is equipped with a water
softener designed to remove minerals and salts
from the water supply, which would have a det-
rimental or adverse effect on the operation of
the appliance.
and mmol/l (millimol per litre - international unit
for the hardness of water).
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.
The higher the content of these minerals and
salts, the harder your water is.
Water hardness is measured in equivalent
scales, Clarke degrees, French degrees (°TH)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Water hardness
Adjusting the water hardness
setting
Use of salt
Clarke
64 - 88
53 - 63
46 - 52
36 - 45
28 - 35
23 - 27
18 - 22
13 - 17
5 - 12
°TH
91 - 125
76 - 90
65 - 75
51 - 64
40 - 50
33 - 39
26 - 32
19 - 25
7 - 18
mmol/l
9,0- 12,5
7,6 - 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
3,3 - 3,9
2,6 - 3,2
1,9 - 2,5
0,7 - 1,8
< 0,7
manually
electronically
level 10
level 9
2
2
2
2
2
2
1
1
1
1
yes
yes
yes
yes
yes
yes
yes
yes
yes
no
level 8
level 7
level 6
level 5
level 4
level 3
level 2
< 5
< 7
level 1
The water softener must be set in both ways:
manually, using the water hardness dial and
electronically.
Setting the water softener manually (see table)
The water softener is factory set at position 2.
Set switch to position 1 or
2
Setting the water softener electronically (see table)
The water softener is factory set at position 5.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Press the On/Off button. The appliance
current level set. The flashing is repea-
ted with a pause of a few seconds.
Examples: 5 flashes, pause, 5 flashes,
pause, etc... = level 5.
must be in setting mode.
2. Press and hold Programme selection/
Cancel button until programme light A
flashes and programme light B illuminates
with fixed light.
4. To change the level, presstheProgramme
selection/Cancel button. Each time the
button is pressed the level increases (level
1 follows level 10). The End of pro-
3. After a few seconds:
– programme light B turns off
– programme light A goes on flashing
gramme light indicates the new setting.
5. To memorise the operation, switch off the
dishwasher.
– End of programme light starts flashing:
the number of flashes corresponds to
Use of dishwasher salt
CAUTION!
Use only special salt suitable for dishwashers.
Unscrew the cap.
Only before filling with Using the funnel provided,
salt for the first time, fill pour in the salt until the
the salt container with wa- container is filled with salt.
ter.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
Immediately start a complete programme.
IMPORTANT!
Waterwill overflowfrom the containerassaltisadded.
Remove any trace of salt. Replace the cap tightly
turning it clockwise until it
stops with a click.
IMPORTANT!
Top up the special salt when the light on the
control panel illuminates.
Use of rinse aid
Open the lid.
Fill up with rinse aid. The Clean up any rinse aid
maximum level for filling is which overflows. Close
indicated by "max"
the lid and press until it
locks.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION!
Never fill the rinse aid dispenser with any other substances (e.g. dishwasher
cleaning agent, liquid detergent). This would damage the appliance.
Top up the rinse aid indica-
tor (B) becomes clear
Adjusting the dosage of rinse aid
Increase the dose if there are drops of water or lime Reduce the dose if there are whitish streaks on the
spots on the dishes after washing.
dishes or a bluish film on glassware or knife blades.
Open the lid.
Set the dosage level. (The Close the lid and pressun-
dose is factory set in po- til it locks.
sition 4).
Load cutlery and dishes
– Dishes and cutlery must not impede the
rotation of the spray arms.
Sponges, household cloths and any object that
can absorb water may not be washed in the
dishwasher.
– Load hollow items such as cups, glasses,
pans, etc. with the opening downwards so
that water cannot collect in the container
or a deep base.
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in pans
– Dishes and items of cutlery must not lie
inside one another, or cover each other.
• When loading the dishes and cutlery, please
note:
12
Download from Www.Somanuals.com. All Manuals Search And Download.
– To avoid damage to glasses, they must
not touch.
these items will not dry as well as porcelain
and steel items.
– Lay small objects in the cutlery basket.
• Light items (plastic bowls etc.) must be loa-
ded in the upper basket and arranged so
they do not move.
• Plastic items and pans with non stick coat-
ings have a tendency to retain water drops;
For washing in the dishwasher the following cutlery and dishes
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or mother-of-
pearls handles.
• Only wash stoneware in the dishwasher if it is
specially marked as being dishwasher-safe by the
manufacturer.
• Plastic items that are not heat resistant.
• Glazed patterns may fade if machine washed
frequently.
• Older cutlery with glued parts that are not tempera-
ture resistant.
• Silver and aluminium parts have a tendency to dis-
colour during washing: Residues, e.g. egg white,
egg yolk and mustard often cause discolouring and
staining on silver. Therefore always clean left-overs
from silver immediately, if it is not to be washed
straight after use.
• Bonded cutlery items or dishes.
• Pewter or copper items.
• Lead crystal glass.
• Steel items prone to rusting.
• Wooden platters.
• Items made from synthetics fibres.
Load cutlery. For best re- Place knives and other
Load the lower basket. Ar-
sults we recommend you items of cutlery with sharp range serving dishes and
to use the cutlery grid pro- points or edges with their large lids around the edge
vided (if the size and di- handles facing upwards. of the basket.
mensions of the cutlery
allow it)
Risk of injury!
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Load upper basket. Light For taller items, the cup
items (plastic bowls etc.) racks can be folded up-
must be loaded in the up- wards.
per basket and arranged
so they do not move.
Adjusting the height of the
upper basket
If washing very large plates you can load them
in the lower basket after moving the upper bas-
ket to the higher position.
Maximum height of the dishes in:
upper basket
lower basket
With upper basket raised
With upper basket lowered
20 cm
24 cm
31 cm
27 cm
IMPORTANT!
When the basket is in the higher position you will not
be able to use the cup racks.
Move the front runner
Refit the basket in the
stops (A) of the upper bas- higher position and re-
ket outwards and slide the place the stops (A) in their
basket out.
original position.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Use of detergent
IMPORTANT!
Observe the manufacturer’s dosing and stor-
age recommendations.
Only use detergents suitable for dishwashers.
Open the lid.
Fill in the detergent in
compartment A.
Observe the dosing lev-
els.
For programmes with pre- When using detergent
Close the lid.
wash add an additional
detergent dose in com-
partmentB.
tablets: place detergent
tablets in compartment A.
cleaning power during short washing pro-
grammes. Therefore, please use long washing
programmes when using detergent tablets, to
ensure the complete removal of detergent
residuals.
Detergent tablets
Detergent tablets from different manufacturers
dissolve at different rates. For this reason,
some detergent tablets do not attain their full
Unloading the dishwasher
• Hot dishes are sensitive to knocks.
The dishes should therefore be allowed to
cool down before removing from the appli-
ance.
• Empty the lower basket first and then the
upper one; this will avoid water dripping from
the upper basket onto the dishes in the lower
one.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
• Water may appear on the sides and the door
of the dishwasher as the stainless steel will
eventually become cooler than the dishes.
CAUTION!
When the washing programme has finished, it
is recommended that the dishwasher is un-
plugged and the water tap turned off.
Care and cleaning
Cleaning the filters
IMPORTANT!
NEVER use the dishwasher without filters. In-
correct repositioning and fitting of the filters will
produce poor washing results.
Clean filters A, B and C
thoroughly under running
water.
Turn the handle about 1/4 Remove filter A from the
turn anticlockwise and re- base of the washing com-
move filters B and C.
partment.
Replace the filters and
lock by turning the handle
clockwise to the stop.
If residues of soil have clogged the holes in the
spray arms, remove them with a cocktail stick.
Cleaning the spray arms
NEVER try to remove the spray arms.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Leave the inside of the machine clean.
External cleaning
Clean the external surfaces of the machine and
control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or sol-
vent (acetone, trichloroethylene etc....).
Frost precautions
Avoid placing the machine in a location where
the temperature is below 0°C. If this is
unavoidable, empty the machine, close the ap-
pliance door, disconnect the water inlet pipe
and empty it.
Internal cleaning
Ensure that the seals around the door, the de-
tergent and rinse aid dispensers are cleaned
regularly with a damp cloth.
We recommend every 3 months to runthewash
programme for heavy soiled dishes using de-
tergent but without dishes.
Moving the machine
Ifyou have to move themachine(movinghouse
etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge ho-
ses.
Prolonged periods of non-
operation
If you are not using the machine for any pro-
longed period of time you are advised to:
1. Unplug the appliance and then turn off the
water.
4. Pull the machine out together with the ho-
ses.
Avoid over tilting the machine during transpor-
tation.
2. Leave the door ajar to prevent the forma-
tion of any unpleasant smells.
Environment concerns
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic com-
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ponents are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging
materials in the appropriate container at the
community waste disposal facilities.
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose of
them.
• Dispose of the door catch. This prevents
children from trapping themselves inside
and endangering their lives.
CAUTION!
When a unit is no longer being used:
What to do if…
The dishwasher will not start or stops during
operation.
Certain problems are due to the lack of simple
maintenance or oversights, which can be
solvedwith thehelp ofthe indications described
in the chart, without calling out an engineer.
Switch off the dishwasher and carry out the fol-
lowing suggested corrective actions.
Fault code and malfunction
Possible cause and solution
• continuous flashing of the start/cancel indicator • The water tap is blocked or furred with limescale.
light
Clean the water tap.
• 1 intermittent audible signal
• The water tap is turned off.
Turn the water tap on.
• 1 flash of the "end of programme" indicator light
The dishwasher does not fill with water.
• Thefilter(wherepresent)inthethreadedhosefitting
at the water inlet valve is blocked.
Clean the filter in the threaded hose fitting.
• The water inlet hose has not been correctly laid or
it is bent or squashed.
Check the water inlet hose connection.
• continuous flashing of the start/cancel indicator • The sink spigot is blocked.
light
Clean out the sink spigot.
• 2 intermittent audible signals
• The water drain hose has not been correctly laid or
it is bent or squashed.
Check the water drain hose connection.
• 2 flashes of the "end of programme" indicator
light
The dishwasher will not drain.
• continuous flashing of the start/cancel indicator • Anti-flood device is activated.
light
Close the water tap and contact your local Service
Force Centre.
• 3 intermittent audible signals
• 3 flashes of the "end of programme" indicator
light
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault code and malfunction
The programme does not start.
Possible cause and solution
• The dishwasher door has not been properly closed.
Close the door.
• The main plug is not plugged in.
Insert the mains plug.
• The fuse has blown in the household fuse box.
Replace the fuse.
Once these checks have been carried out;
switch on the dishwasher. The programme will
continue from the point at which it was inter-
rupted.
If the malfunction or fault code reappears con-
tact the Service Force Centre.
For other fault codes not described in the above
chart, please contact your Service Force Cen-
tre.
Contact your local Service Force Centre, quot-
ing the model (Mod.), product number (PNC)
and serial number (S.N.). This information can
be found on the rating plate located on the side
of the dishwasher door.. So that you always
have these numbers at hand, we recommend
you to make a note of them here:
Mod. :. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The wash results are not satisfactory
The dishes are not clean
• The wrong washing programme has been selected.
• The dishes are arranged in such a way as to stop
water reaching all parts of the surface. The baskets
must not be overloaded.
• The spray arms do not rotate freely due to incorrect
arrangement of the load.
• The filters in the base of the washing compartment
are dirty or incorrectly positioned.
• Too little or no detergent has been used.
• Where there are limescales deposits on the dishes;
the salt container is empty or the incorrect level of
the water softener has been set.
• The drain hose connection is not correct.
• The salt container cap is not properly closed.
The dishes are wet and dull
• Rinse aid was not used.
• The rinse aid dispenser is empty.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
The wash results are not satisfactory
There are streaks, milky spots or a bluish coating on • Decrease rinse aid dosing.
glasses and dishes
Water drops have dries onto glasses and dishes
• Increase rinse aid dosing.
• The detergent may be the cause. Contact the de-
tergent manufacturer’s consumer care line.
If after all these checks, the problem persists,
contact your local Service Force Centre.
Technical data
Dimensions
Width x Height x Depth (cm)
44,6 x 81,8-89,8 x 55,5
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher’s door.
Water supply pressure
Minimum
Maximum
0,05 MPa (0,5 bar)
0,8 MPa (8 bar)
Capacity
place settings
9
Consumption values
The consumption values are intended as a
guide and depends on the pressure and the
temperature of the water and also by the var-
iations of the power supply and the amount of
dishes.
Consumption values
Programme duration (in Energyconsumption (in
Programme
Intensive 65°
Water (litres)
minutes)
110 - 120
100 - 110
30
kWh)
1,5 - 1,7
1,4 - 1,5
0,8
18 - 20
18 - 20
8
Normal 65°
65° A 30'
1)
120 - 130
0,8 - 0,9
12 - 13
Eco 50°
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumption values
Programme
Programme duration (in Energyconsumption (in
Water (litres)
minutes)
kWh)
Rinse and Hold
11
0,1
5
1) Test programme for Test Institutes
Hints for test institutes
Testing in accordance with EN 60704 must be
carried out with appliance fully loaded and us-
ing the test programme (see "Consumption
values").
aid dispenser have been filled with salt and
rinse aid respectively and using the test pro-
gramme (see "Consumption values").
Test in accordance with EN 50242 must be
carried out when the salt container and rinse
Full load: 9 standard place settings
Amount of detergent required
Rinse aid setting
5 g + 20 g (Type B)
position 4 (Type III)
Upper basket without smaller bowl Upper basket with smaller bowl and
Cutlery basket
and salad-bowl
salad-bowl
21
Download from Www.Somanuals.com. All Manuals Search And Download.
cup racks: position A
Lower basket
Installation
WARNING!
Water inlet hose with safety
valve
Connect the inlet hose to a water tap with an
external thread of 3/4”.
Any electrical and/or plumbing work required to
install this appliance should be carried out by a
qualified electrician and/or plumber or compe-
tent person.
After connecting the double-walled water inlet
hose, the safety valve is next to the tap.
If the water inlet hose leaks, the safety valve
cuts off the water supply.
Water connection
WARNING!
The dishwasher must not be connected to open
water appliances or instantaneous water heat-
ers. This dishwasher may be fed with either hot
(max. 60°) or cold water. Nevertheless we ad-
vise you a cold water supply.
WARNING!
Only use, for connection to the water mains,
new hose-set; old hose-set must not be reused.
CAUTION!
If the machine is connected to new pipes or
pipes which have not been used for a long time,
you should run the water for a few minutes be-
fore connecting the inlet hose.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
If the water inlet hose or the safety valve is
damaged, remove the mains plug immediately.
WARNING!
The electrical cable for the safety valve is in the
double-walled water inlet hose and is live.
Therefore do not immerse the water inlet hose
or the safety valve in water.
Take care when installing the water inlet hose
. Place the water inlet hose in such a way that
it is always lower than the bottom edge of the
safety valve.
CAUTION!
A water inlet hose with safety valve MUST only
be replaced by your local Service Force Centre.
Drain hose
Connect drain hose to the Required height: 30 to100 Ensure that the hoses are When connecting the
sink.
cm above bottom of the
dishwasher.
not kinked, crushed or en- drain hose to an under
tangled.
sink trap spigot, the entire
plastic membrane (A)
must be removed. Fail-
uretoremoveallthemem-
brane will result in food
particles building up over
time eventually blocking
the dishwasher drain hose
spigot.
If you use a drain hose extension the total
length should not be longer than 4 metres.
Likewise the internal diameter of the couplings
used for connections to the waste outlet must
be no smaller than the diameter of the hose
provided.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
Electrical connection
Thedishwashermustbesecuredagainsttilting.
Therefore make sure that the counter it is fixed
under, is suitably secured to a fixed structure
(adjacent kitchen units cabinets, wall).
CAUTION!
Safety standards require the appliance to be
earthed.
Prior to using the appliance for the first time,
ensure that the rated voltage and type of supply
on the rating plate match that of the supply
where the appliance is to be installed.
The fuse rating is also to be found on the rating
plate.
Always plug the mains plug into a correctly in-
stalled shockproof socket. Multi-way plugs,
connectors and extension cables must not be
used.
This could constitute afire hazardthroughover-
heating.
If necessary, have the domestic wiring system
socket replaced. In case that the electrical ca-
ble has to be replaced, contact your local Serv-
ice Force centre.
This dishwasher is designed to be fitted under
a kitchen counter or work surface.
No further openings for the venting of the
dishwasher are required, but only to let the wa-
ter fill and drain hose and power supply cable
pass through.
The dishwasher incorporates adjustable feet to
allow the adjustment of the height.
During all operations that involve accessibility
to internal components the dishwasher has to
be unplugged.
Be sure that once the appliance has been in-
stalled, it is easily accessible for the service
engineer in the event that a repair is required.
Levelling
Good levelling is essential for correct closure
and sealing of the door.
When the appliance is correctly levelled, the
door will not catch on either side of the cabinet.
If the door does not close correctly, loosen or
tighten the adjustable feet until the machine is
perfectly level. (See enclosed template).
The plug must be accessible aftertheappliance
has been installed.
Never unplug the appliance by pulling on the
cable. Always pull the plug.
The manufacturer accepts no liability for failure
to observe the above safety precautions.
Fitting under a counter
IMPORTANT!
Carefullyfollowtheinstructionsontheenclosed
template for building in the dishwasher and fit-
ting the furniture panel.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
117972110-012008
Download from Www.Somanuals.com. All Manuals Search And Download.
|