DISHWASHER
ZDI 6041
INSTRUCTION BOOK
152975 53/0
UK
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing programmes
Recommended
Programme
Type of load and
degree of soil
Starting position
of the programme
selector dial
Required
push button
Cycle
description
quantity of detergent
wash
prewash
Cold prewash
Main wash up to 65°C
1 cold rinse
1 hot rinse
Heavy soil.
Crockery, cutlery, pots
and pans
HEAVY SOIL
*
25 g
5 g
A
B
On/Off
65°C
Drying
Main wash up to 65°C
1 cold rinse
1 hot rinse
Normal soil.
Crockery and cutlery
NORMAL SOIL
65°C
30 g
30 g
/
/
/
/
On/Off
On/Off
On/Off
Drying
Light soil.
Crockery, cutlery and
party crockery
Main wash up to 65°C
1 cold rinse
1 hot rinse
QUICK WASH
65°C
**
C
D
Partial load (to be
completed later in the
day).
RINSE AND
HOLD
1 cold rinse
Testing programme for EN 50242 (see "Hints for Test Centres).
*
This is a special programme for quick washing a full load of lightly soiled dishes, glasses and crockery (except pots) so that you
may re-use them promptly.
**
Operating sequence
1. Check the filters
8. Start the programme
Ensure they are clean and properly positioned (see
"Maintenance and cleaning" - Instruction book part 1).
Depress the On/Off push button.
The On/Off indicator light will come on and the machine
will start.
2. Check that there is rinse aid and salt
If you wish to interrupt the washing programme at any
time press this button again.
(See "Instruction book - part 1")
3. Load the dishes
9. At the end of the washing programme
Remove any scraps of food.
At the end of the programme the dishwasher will
automatically stop.
The On/Off indicator light remains on until the On/Off
push button is depressed.
Pull the lower basket out and arrange the saucepans,
plates and cutlery in it.
Pull the upper basket out and arrange the plates,
saucers, glasses and cups etc. in it.
Slide the baskets back into the machine.
10.Switch off the dishwasher
Switch off the dishwasher by pressing the On/Off push
4. Ensure that the spray arms can
rotate freely
button and open the door.
Wait a few minutes before removing the dishes; in this
way they will be cooler and the drying will be improved.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
5. Measure out detergent
Add the required amount of detergent into the dispenser
according to the "Washing programmes" chart.
Close the detergent dispenser lid.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
6. Close the dishwasher door
In general it is not advisable to open the door while the
machine is working; if the door is opened however, a
safety device ensures that the machine stops.
7. Set the programme
Turn the programme selector dial clockwise until the
letter of the programme you wish to select corresponds
with the programme marker on the control panel.
Important!
Care must be taken if the door is opened during the hot
phase or immediately after a programme has finished, as
steam may escape.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your appliance
Loading your appliance
Before placing dishes in the machine, remove any scraps of
food, to avoid clogging the filters and consequently reducing
the performance.
The upper basket
The upper basket is designed for plates (dessert plates,
saucers, dinner plates of up to 25 cm in diameter), salad
bowls, cups and glasses.
Do not load very small items which can fall through the
baskets.
Arrange items so that water can reach all surfaces.
Light items (plastic bowls etc.) should be loaded in the upper
basket and arranged so they do not move.
The lower basket
The lower basket is designed to take saucepans, lids, plates,
salad bowls, cutlery etc.
Serving dishes and large lids should be arranged around the
edge of the basket, ensuring that the upper spray arm can
turn freely.
US64
In case that plates are loaded in the upper
basket:
load them starting from the rear positions of the basket, tilting
them forwards and avoiding the front positions near the door.
UI48
UI21
The cutlery basket
Long bladed knives stored in an upright position are a
potential hazard.
US71
Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
Take care when loading or unloading sharp items such as
knives.
Before closing the door, ensure that the spray arms can
rotate freely.
Cutlery should be placed in the removable cutlery basket with
the handles facing downwards.
If the handles protrude from the bottom of the basket,
obstructing the lower spray arm, load the cutlery with the
handles facing upwards.
Adjusting the height of the upper
basket
If washing very large plates (over 27 cm and up to 32 cm in
diameter) you can load them in the lower basket after moving
the upper basket to the higher position.
Mix spoons with other cutlery to prevent them from sticking
together.
For best results we recommend to use the cutlery grids
To move to the higher position proceed as follows:
provided (if the size and the dimensions of the cutlery allow it).
The cutlery basket is in two parts which can be separated to
give greater loading flexibility. To separate the two parts, slide
them horizontally in opposite directions and pull them apart. To
reassemble, reverse the procedure.
1. Move the front runner
A
stops (A) of the upper
basket outwards and
slide the basket out.
2. Refit the basket in the
higher position and
replace the stops (A) in
their original position.
RC01
When the top basket is in the higher position it will only
take plates up to 20 cm in diameter and you will not be
able to use the raised cup racks.
UI62
UI63
Attention!
After loading your machine always close the door, as an
open door can be a hazard.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Hints for test centres
Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser
Test standard:
EN 50242
Reference programme:
Load:
HEAVY SOIL 65°C
12 standard place settings
position 5
Rinse aid selector:
Detergent dosage:
25 g in the dispenser
5 g on the dispenser lid
Arrangement upper basket
Arrangement lower basket
Arrangement cutlery basket
Technical specifications
Dimensions
Width
59.6cm
Height
Max depth
81.8 - 87.8 cm
57.5 cm
Max depth with open door
111.4 cm
Electrical connection
Motor rating during wash
Power of heating element
Overall power
Voltage
220/240 V - 50 Hz
200 W
2100 W
2300 W
Water supply pressure
Minimum
Maximum
50 kPa (0.5 bar)
800 kPa (8 bar)
Capacity
12 place settings
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local Service Force
Centre by telephoning:
08705 929929
Your telephone call will be automatically routed to the Service Force centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the website at
Before calling out an engineer, please ensure you read the details under the heading Something not working.
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number (found on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls.
Customer Care Department
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products please contact our
Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727727 ( )
*
calls to this number may be recorded for training purposes
*
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee Conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part thereof is proved to be
defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE
for labour, materials or carriage on condition that:
G The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
G The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s instructions.
G The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not authorised by us.
G All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
G Any appliance or defective part replaced shall become the Company’s property.
G This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case
a premium will be charged.
Exclusions
This guarantee does not cover:
G Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts
of glass or plastic.
G Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom.
G Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements.
G Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home subject to the
following qualifications:
G The guarantee starts from the date you first purchased your product.
G The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this
brand or range of products.
G This guarantee relates to you and cannot be transferred to another user.
G Your new home is within the European Community (EC) or European free Trade Area.
G The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household.
G The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will
then ensure that the local service Organisation is aware of your move and able to look after you and your appliances.
France
Senlis
+33 (0) 3 44 62 29 29
GermanyNurnberg
ItalyPordenone
+49
(0)
(0)
800
234
7378
39
+39
0434
4700
Sweden
UK
Stockholm
Slough
+46 (0) 8 672 53 90
+44 (0) 1753 219897
+353 (0) 14090753
Ireland
Dublin
7
Download from Www.Somanuals.com. All Manuals Search And Download.
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as
refrigerators, cookers, vacuum cleaners, chain saws and lawn mowers) are sold each year
to a value of approx. 14 billion USD in more than 150 countries around the world.
©
Electrolux Household Appliances Limited 2002
0 01/02
Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction Book
DISHWASHER
- Before use
- Maintenance
- Installation
Contents
Before use
2
2
2
3
3
External cleaning
Prolonged periods of non-operation
Frost precautions
5
Setting the water softener
Filling with salt
Filling with rinse aid and adjusting the dose
Use of detergent
5
5
5
Moving the machine
Something not working
6
Hints and tips
4
Installation
7
7
7
7
Maintenance and cleaning
Internal cleaning
Cleaning the filters
5
5
5
Water supply connections
Water outlet connection
Electrical connection
Important safety information
It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance
be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is
left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety
information.
This information has been provided in the interest of your safety. You MUST read it carefully before installing or using the
appliance.
G Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
G When finishing loading or unloading close the door, as an
open door can be a hazard.
G Do not sit or stand on the open door.
Installation
G This appliance is heavy. Care should be taken when
moving it.
G It is dangerous to alter the specifications or attempt to
modify this product in any way.
G Care must be taken to ensure that the appliance does not
stand on the electrical supply cable.
G Any electrical work required to install this appliance should
G Isolate the appliance from the power supply and turn off the
water supply after use.
G Care should be taken when cleaning the bottom door seal
and hinge area as any exposed metal edges may cut if
be carried out by a qualified electrician or competent
care is not taken.
person.
G This product should be serviced by an authorised Service
G Any plumbing work required to install this appliance should
engineer, and only genuine spare parts should be used.
be carried out by a qualified plumber or competent person.
G Under no circumstances should you attempt to repair the
machine yourself. Repairs carried out by inexperienced
persons may cause injury or serious malfunctioning.
Child Safety
G This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the controls
or play with the product.
Contact your local Service Force Centre.
Always insist on genuine spare parts.
G Keep all packaging well away from children.
Conservation
In the interest of the environment:
G Keep all detergents in a safe place out of children's reach.
G Materials marked with the symbol
are recyclable.
During Use
G Items that are contaminated by petrol, paint, steel or iron
debris, corrosive, acidic or alkaline chemicals must not be
washed in this dishwasher.
G Under no circumstances should you open the door whilst
the appliance is in operation. Always turn off the appliance
before opening the door.
G Only use detergent specifically designed for use in
dishwashers.
G Check with your local Council or Environmental Health
Office to see if there are facilities in your area for re-cycling
this appliance.
G When the appliance is to be scrapped, cut off the power
supply cable and make the door closing device unusable to
prevent young children from being trapped inside.
G Help to keep your country tidy - use authorised disposal
sites for your old appliance.
G Long bladed knives stored in an upright position are a
potential hazard.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Before using your dishwasher for the
first time:
Filling with salt
Attention!
Only use salt specifically designed for use in
dishwashers.
All other types of salt not specifically designed for use in
dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting a washing
programme. This will prevent any grains of salt or salty
water, which may have been spilled, remaining on the
bottom of the machine, which may cause corrosion.
1. Ensure that the electrical and water connections comply
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill
with salt
5. Fill the rinse aid dispenser.
6. Run a "Rinse and Hold" programme.
To fill:
Setting the water softener
1. To fill with salt, unscrew the cap of the salt container.
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, Clarke,
French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
The dishwasher is factory set at level 2.
If this level is not suitable for your area the softener should be
adjusted.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3. Using the funnel (if
provided), pour in the salt
until the container is full.
Do not worry if water over
flows from the unit when
filling with salt, this is quite
normal.
SALET
SAL
SALZ
SEL
4. Replace the cap making
sure that there is no trace
of salt on the screw thread
or on the gasket.
SR06
If your water is level 0 it is already soft and therefore
there is no need to use salt.
5. Screw on the cap tightly.
In this case adjust the water softener on level 1 without
using salt.
The salt container will require topping up periodically.
According to the model, an indicator reminds you when filling
with salt:
Water hardness
Clarke
degrees
PPM
(Parts per
Million)
French
degrees
(°TH)
Use of
salt
Level
A) The salt cap has a refill
indicator window in the centre.
A green float is clearly
0
1
2
3
4
5
0 - 80
0 - 6
NO
0 - 8
81 - 200
201 - 400
401 - 600
601 - 800
801 - 900
7 - 14
YES
YES
YES
YES
YES
9 - 20
visible when there is salt
inside the container, and
almost disappears when the
salt has finished reminding
you to add salt.
15 - 28
29 - 42
43 - 56
57 - 63
21 - 40
41 - 60
61 - 80
81 - 90
SR11
B) A salt indicator light on the
control panel will come on
when the salt has finished.
Only for dishwasher models with salt refill
indicator light:
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been
replenished, assuming the dishwasher remains switched
on. If you are using salts that take longer to dissolve then
this can take longer.
if the water softener has been adjusted on level 1 without use
of salt, the salt refill indicator light on the control panel will
always remain illuminated when the machine is switched on.
The function of the machine is not affected..
To adjust the water softener
With a screwdriver turn the selector on the upper front corner
of the machine until the level
required corresponds with the
marker.
5
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Rinse aid
Use of detergent
Only use detergents specifically designed for use in
dishwashers.
Rinse aid is automatically added during the last rinse,
ensuring thorough rinsing, and spot and streak free drying.
The dispenser, which is positioned inside the door, holds
about 110 ml of rinse aid, which is sufficient for 16 - 40
dishwashing programmes, depending upon the dosage
setting.
We recommend the use of Finish detergents which are
available in the following options:
Finish Double Action Tablets. Each tablet has the exact
amount of detergent required, simply place in the dispenser.
Finish Powder recommended for every day use.
Finish Liquid Gel ideal for every day use. As the gel is extra
gentle is it recommended for fine bone china.
Filling with rinse aid
1. Open the container by turning the lid (A) anticlockwise.
If using powder detergents proceed as follows:
2. Add the rinse aid until the container is completely full.
The indicator (B) will be completely dark.
1. Open the dispenser lid by pulling the catch (D).
2. Add the detergent according to the recommended
quantity given in the "Washing programmes" chart
(see "Instruction Book - Part 2").
As all detergents are not the same, you should also
consult the instructions on the packet.
B
5
4
6
x
a
2
m
3. Always close the lid.
1
4. If the programme has a prewash add a little amount of
detergent over the lid of the dispenser. Follow the
recommended quantity given in the "Washing
A
BR01
BR03
programmes" chart (see "Instruction Book - Part 2").
3. Top up the rinse aid when the indicator (B) becomes
Min = 15 g
Max = 30 g
clear.
D
(Only for models with rinse aid indicator light)
Top up with rinse aid when the rinse aid indicator light on
the control panel illuminates.
X
A
M
I N
M
Ensure that the lid is closed after every refill.
Do not put liquid detergent in the rinse aid compartment.
Clean up any rinse aid spilt during filling with an absorbent
cloth to avoid excess foaming during the next wash.
DE17
DE02
If using detergent in tablets proceed as
follows:
1. For all programmes; place 1 tablet inside the detergent
Adjusting the dose
dispenser.
According to the finish and drying results obtained, adjust the
dose of rinse aid by means of the 6 position selector (C)
(position 1 minimum dosage, position 6 maximum dosage).
2. Always close the lid.
3. For all programmes with prewash; place a portion of a
further tablet on the lid of the detergent dispenser.
Increase the dose if there are drops of water or lime spots on
the dishes after washing.
If your dishwasher has a SID dispenser and you require a
prewash, put the extra detergent into the SID dispenser
and not on the lid of the detergent dispenser.
Reduce it if there are sticky whitish streaks on the dishes.
Insufficient quantities of detergent will produce poor
washing results, whereas an excessive amount of
detergent will not improve washing results and is also
wasteful.
Using no more than the correct amount also contributes
to reducing pollution.
C
5
4
6
x
3
a
2
m
1
BR02
Compact detergents with enzymes
In these compact powders the environmentally unfriendly
components have been replaced by natural enzymes and
other more biodegradable substances.
The enzymes deploy their full dirt dissolving power at a
temperature as low as 50°C.
By choosing the 50°C programmes (if available) you can
therefore achieve the same cleaning results that would
otherwise be achievable only with 65°C programmes and
conventional detergents.These new compact powders are
generally phosphate-free.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Hints and tips
To save energy
Place dishes in the machine immediately after every meal and
wait until the dishwasher is full before washing.
If necessary run the Rinse and Hold programme (see
"Washing Programmes" chart) so that any food scraps do not
become caked on the dishes while you are waiting to run the
complete wash programme.
Do not prewash dishes under running water.
For best washing and drying results
Before loading, remove all scraps of food and soak very
heavily soiled pots and pans.
Arrange saucepans, cups and glasses etc. upside-down.
Tilt items with convex or concave surfaces so that the water
drains off easily.
Avoid contact between the dishes as far as possible.
Items not suitable for dishwashers
The following items should not be washed in the
dishwasher (unless they are sold as dishwasher proof):
- Cutlery with wooden or horn handles or glued parts
- bronze cutlery
- saucepans with wooden handles
- aluminium ware
- crystal ware
- leaded glass
- plastic items
- antique or fine decorated china
Certain types of decoration can discolour when washed in a
dishwasher.
Crystal-ware and plastic objects, if not guaranteed dishwasher
proof should be washed by hand.
Certain types of glass can also become opaque after being
washed several times in a dishwasher.
A chemical reaction can occur between silver cutlery and
stainless steel cutlery. As a precaution, do not wash together.
Iron and cast iron objects can rust and stain other items.
Aluminium tends to go black, copper, pewter and brass tend to
stain.
If in doubt check with manufacturer of the item.
When buying new dishes, ensure that they are
dishwasher proof.
For best results we recommend the use of Finish detergents, rinse aid and salt.
P OURING
PACK
W
E
N
N
O
I
T
LE
B
AC
U
O
D
L
I
Q
U
I
D
G
E
L
P
O
W
D
E
R
R
I
N
S
E
CONCENTRATED DISHWASHER DETERGENT
DE15
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and cleaning
Internal cleaning
Ensure that the seals around the door, the detergent and rinse
aid dispensers are cleaned regularly with a damp cloth.
We recommend the use of Finish Dishwasher Cleaner every
3 months or run a 65°C wash without dishes using detergent.
Regular use of Finish Dishwasher Cleaner cleans
inaccessible parts, eliminates unpleasant food odours and
helps prevent the build-up of limescale.
The dishwasher must not be used without filters.
Incorrect repositioning and fitting of the filters will
produce poor washing results.
Cleaning the filters is vital to ensure correct operation of
the machine.
External cleaning
Clean the external surfaces of the machine and control panel
with a damp soft cloth. If necessary use only neutral
detergents. Never use abrasive products, scouring pads or
solvent (acetone, trichloroethylene etc....).
Cleaning the central filter
(After each wash)
Scraps of food may accumulate in the drain filter (A) and
should be removed by rinsing the filter under running water.
To remove the drain filter
Prolonged periods of non-operation
If you are not using the machine for any period of time you are
advised to:
- simply pull it out by the handle.
Once cleaned, refit the filter by pushing it back to its original
position until it engages.
1. Unplug the appliance and then turn off the water.
2. Fill the rinse aid dispenser.
3. Leave the door ajar to prevent the formation of any
unpleasant smells.
4. Leave the inside of the machine clean.
A
Frost precautions
MA04
MA19
Avoid placing the machine in a location where the temperature
is below 0°C. If this is unavoidable, empty the machine, close
the appliance door, disconnect the water inlet pipe and empty
it.
Cleaning the large filter
(Every week)
If necessary clean the large filter (B) on both sides under
running water, using a brush.
To remove the large filter
Moving the machine
If you have to move the machine (moving house etc....):
1. Remove the spray arm by pulling it upwards on one side.
2. Turn the column (C) anticlockwise by 90° and then slide
out the filter.
1. Unplug it.
3. Once cleaned refit it following the above instructions in
2. Turn the water tap off.
reverse order.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
4. Ensure the filter is in its original position, the handle of
the drain filter should be pointing towards the front of the
appliance.
90°
B
C
MA20
MA05
MA21
MA18
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Something not working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer.
Before contacting your local Service Force Centre, please carry out the checks listed below.
Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a
charge will be made even if the appliance is in guarantee.
Symptom
Solution
The machine will not start
G The door has not been properly closed.
G The plug is not properly inserted in the power socket.
G There is a power failure.
The machine does not fill with water
G Ensure the water tap is open.
G Ensure the mains water supply has not been cut off.
G The inlet hose may be squashed or bent. Reposition the hose.
G The inlet hose may be blocked. Switch off the water supply and clean the filter.
The filters are blocked
G Clean the filters (refer to "Maintenance and cleaning").
G Ensure the crockery is loaded correctly.
The spray arms are not rotating
The dishwasher will not drain
G The drain hose may be squashed or bent. Reposition the hose.
G The sink may be blocked. Clear any blockages.
G The drain hose extension is not correct. Follow the instructions for connecting
to the waste.
G There is no vent in the end of the drain hose.
The machine is noisy
G Dishes are rattling against each other, refer to “Loading your machine”.
G The spray arms are knocking against the dishes. Refer to "Loading your
machine".
The door is difficult to close
G The dishwasher is not level, or not properly built-in.
Visible lime deposits or white film
on the dishes
G Check that there is salt and that the salt cap is tight.
G Check that the right level of the water softener is set.
The dishes are not quite dry
G The rinse aid has run out or too little is being used.
The dishes are not clean (poor wash)
G The baskets are too full.
G The dishes have not been arranged properly.
G The spray arms do not rotate
G The spray arms are clogged.
G The filters are clogged.
G The filters are not in the correct position.
G Not enough detergent has been used or it is unsuitable.
G The detergent is old or has gone hard.
G The salt container cap is not properly closed.
G The washing programme selected is too gentle.
If after all these checks, the problem persists, contact your
local Service Force Centre, quoting the model and serial
number. This information can be found on the rating plate
located on the right hand side of the dishwasher door.
This product should be serviced by an authorised Service
engineer, and only genuine spare parts should be used.
Under no circumstances should you attempt to repair the
machine yourself.
Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your local
Service Force Centre.
Always insist on genuine spare parts.
Prod.No. ........ Ser. No. .........
Mod. ........
RA01
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
The sink plug must not be in place when the machine is
draining as this could cause the water to siphon back into the
machine.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or competent
person.
Remove all packaging before positioning the machine.
If possible, position the machine next to a water tap and a
drain.
+ 2 m max
Levelling
CS10
Good levelling is essential for correct closure and sealing of
the door. When the appliance is correctly levelled, the door will
not catch on the levelling spacers on either side of the
cabinet. If the door does not close correctly, loosen or tighten
the adjustable feet until the machine is perfectly level.
Attention!
Our appliances are supplied with a with a security device
to protect against the return of dirty water back into the
machine.
If the spigot of your sink has a "no return valve"
incorporated this can prevent the correct draining of your
dishwasher. We advise you therefore to remove it.
Water supply connections
This dishwasher must be plumbed into a cold water supply.
The water pressure must be within the limits given in the
"Technical specifications" (Instruction Book - Part 2).
Electrical connection
This appliance must be earthed.
The manufacturer declines any responsibility should this
safety measure not be observed.
Your local Water Authority will advise you on the average
mains pressure in your area.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation.
Do not use, for connection, old hoses which have been
used in another appliance.
The locknut must be correctly fitted to avoid water leaks.
Avoid bends or kinks in the hose which could prevent or slow
down the water supply.
If the machine is connected to new pipes or pipes which have
not been used for a long time, you should run the water for a
few minutes before connecting the inlet hose. This will prevent
deposits of sand or rust clogging the inlet hose.
If the plug that is fitted to your appliance is not suitable for the
socket, it must be cut off and the appropriate plug fitted.
Important
The wires on the mains lead are coloured in accordance with
the following code:
Green and Yellow -Earth
Blue
Brown
-Neutral
-Live
If you fit your own plug,
the colours of the wires
in the mains lead of
your appliance may not
correspond with the
E
Water outlet hose connection
The end of the drain hose can be connected in the following
ways:
markings identifying the
terminals in your plug.
L
1. To the sink outlet spigot, securing it if necessary with a
N
clip.
2. Hooked over the edge of the sink using the special
curved plastic guide (if provided).
3. To a stand pipe provided with vent-hole, minimum
internal diameter 4 cm.
CE04
2
1
3
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the terminal
in the plug which is marked with the letter "E" or the earth
symbol
or coloured green and yellow.
CS09
2. Connect the Blue (neutral) wire to the terminal in the plug
which is marked with the letter "N" or coloured black.
The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of the
dishwasher.
3. Connect the Brown (live) wire to the terminal in the plug
which is marked with the letter "L" or coloured red.
The plug moulded onto the lead incorporates a 13amp BSI362
fuse. Only ASTA or BSI fuses should be used.
The drain hose can face either to the right or left of the
dishwasher
The plug must not be used if the fuse cover/carrier is lost. The
cover/carrier is indicated by the coloured insert at the base of
the plug.
A replacement cover/carrier must be obtained from your local
Service Force Centre.
Ensure the hose is not bent or squashed as this could prevent
or slow down the discharge of water.
If you use a drain hose extension it must be no longer than 2
metres and its internal diameter must be no smaller than the
diameter of the hose provided.
Likewise the internal diameter of the couplings used for
connections to the waste outlet must be no smaller than the
diameter of the hose provided.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
This appliance complies with the following E.E.C. Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
152981 19/3
3 01/02
Download from Www.Somanuals.com. All Manuals Search And Download.
|