Yamaha Stereo Receiver HTR 6150 User Manual

HTR-6150

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufacturer’s

instructions have been adhered to.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

•

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

Read Instructions – All the safety and operating instructions

should be read before the product is operated.

Retain Instructions – The safety and operating instructions

should be retained for future reference.

Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

Follow Instructions – All operating and use instructions

should be followed.

Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to

overturn.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

Caution-i En

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the antenna

or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70,

provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

e) If the product has been dropped or damaged in any

way, and

When the product exhibits a distinct change in perfor-

mance - this indicates a need for service.

EXAMPLE OF ANTENNA GROUNDING

20 Replacement Parts – When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

ANTENNA

LEAD IN

WIRE

MAST

21 Safety Check – Upon completion of any service or repairs to

this product, ask the service technician to perform safety

checks to determine that the product is in proper operating

condition.

GROUND

CLAMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as

practical.

NEC – NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers)

IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

IMPORTANT: When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to

follow instructions could void your FCC authorization to

use this product in the USA.

NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15

for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will

not result in harmful interference with other electronic

devices.

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found

in the users manual, may cause interference harmful to the

operation of other electronic devices.

Caution-ii En

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

Caution: Read this before operating your unit.

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

18 Before moving this unit, press CSYSTEM OFF to set this

unit in the standby mode, and disconnect the AC power plug

from the wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet.

Voltages are 110–120/220–240 V AC, 50/60 Hz.

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

–

other components, as they may cause damage and/or

discoloration on the surface of this unit.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet, even

if this unit itself is turned off by CSYSTEM OFF.

This state is called the standby mode. In this state, this

unit is designed to consume a very small quantity of

power.

burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

Do not plug in this unit to a wall outlet until all connections

are complete.

Do not operate this unit upside-down. It may overheat,

possibly causing damage.

Do not use force on switches, knobs and/or cords.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

Serial No.:

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

Caution-iii En

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

XM Satellite Radio tuning....................................48

Connecting the XM Mini-Tuner Dock .................... 48

Activating XM Satellite Radio ................................ 49

Basic XM Satellite Radio operations....................... 49

Setting XM Satellite Radio preset channels ............ 51

Displaying the XM Satellite Radio information...... 52

SIRIUS Satellite Radio™ tuning .........................53

Connecting the SiriusConnect™ tuner .................... 53

Activating SIRIUS Satellite Radio™ subscription.. 54

Basic SIRIUS Satellite Radio™ operations ............ 54

Setting the SIRIUS Satellite Radio™ preset

INTRODUCTION

Features ................................................................... 2

Getting started ........................................................ 3

Quick start guide .................................................... 4

Preparation: Check the items..................................... 4

Step 1: Set up your speakers...................................... 5

Step 2: Connect your DVD player and other

components............................................................ 6

Step 3: Press SCENE 1 button................................... 7

What do you want to do with this unit?..................... 8

channels............................................................... 56

Setting the Parental Lock......................................... 56

Displaying the SIRIUS Satellite Radio™

information .......................................................... 58

Using iPod™ ..........................................................59

Controlling iPod™................................................... 59

Using Bluetooth™ components............................61

Pairing the Bluetooth™ adapter and your Bluetooth™

component ........................................................... 61

Playback of the Bluetooth™ component................. 61

Recording...............................................................62

PREPARATION

Connections............................................................. 9

Rear panel.................................................................. 9

Placing speakers....................................................... 10

Connecting speakers................................................ 11

Information on jacks and cable plugs...................... 13

Information on HDMI™.......................................... 14

Audio and video signal flow.................................... 15

Connecting video components................................. 16

Connecting other components ................................. 17

Connecting audio components................................. 19

Connecting a Yamaha iPod™ universal dock or

ADVANCED OPERATION

SET MENU............................................................63

Using SET MENU................................................... 64

1 SOUND MENU.................................................... 65

2 INPUT MENU...................................................... 71

3 OPTION MENU................................................... 73

Remote control features........................................76

Controlling this unit, a TV, or other components.... 76

Setting remote control codes ................................... 78

Using multi-zone configuration............................79

Connecting Zone 2................................................... 79

Controlling Zone 2................................................... 80

Advanced setup......................................................82

Bluetooth™ adapter............................................. 20

Using REMOTE IN/OUT jacks............................... 20

Using the VIDEO AUX jacks on the front panel .... 21

Connecting the FM and AM antennas..................... 21

Connecting the power cable..................................... 22

Setting the speaker impedance................................. 23

Turning on and off the power.................................. 23

Front panel display .................................................. 24

Optimizing the speaker setting

for your listening room .................................... 26

Using AUTO SETUP .............................................. 26

ADDITIONAL INFORMATION

BASIC OPERATION

Troubleshooting.....................................................84

Glossary..................................................................94

Specifications .........................................................97

Index.......................................................................98

Selecting the SCENE templates........................... 30

Selecting the desired SCENE template.................... 30

Creating your original SCENE templates................ 33

Using remote control on the SCENE feature........... 34

Playback ................................................................ 35

Basic operations....................................................... 35

Selecting audio input jacks

APPENDIX

(AUDIO SELECT).............................................. 36

Selecting the MULTI CH INPUT component......... 36

Displaying the current status of this unit on a video

monitor ................................................................ 37

Using your headphones............................................ 37

Muting the audio output........................................... 37

Playing video sources in the background of an audio

source................................................................... 38

Displaying the input source information ................. 38

Using the sleep timer ............................................... 39

Sound field programs........................................... 40

Sound field program descriptions............................ 40

Using audio features............................................. 43

Enjoying high quality sound.................................... 43

Adjusting the tonal quality....................................... 43

Adjusting the speaker level...................................... 43

Selecting the night listening mode........................... 44

FM/AM tuning...................................................... 45

Automatic tuning ..................................................... 45

Manual tuning.......................................................... 45

Automatic preset tuning........................................... 46

Manual preset tuning ............................................... 46

Selecting preset stations........................................... 47

Exchanging preset station........................................ 47

(at the end of this manual)

Front panel................................................................i

Remote control ....................................................... ii

List of remote control codes ................................. iii

About this manual

• yindicates a tip for your operation.

• Some operations can be performed by using either the buttons on the

front panel or the ones on the remote control. In case the button

names differ between the front panel and the remote control, the

button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications

are subject to change in part as a result of improvements, etc. In case

of differences between the manual and product, the product has

priority.

• “MSPEAKERS” or “4DVD” (example) indicates the name of the

parts on the front panel or the remote control. Refer to the attached

sheet or the pages at the end of this manual for the information about

each position of the parts.

• The symbol “☞” with page number(s) indicates the corresponding

reference page(s).

1En

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

Built-in 7-channel power amplifier

Radio tuners

◆ Minimum RMS output power

[U.S.A. and Canada models]

(1 kHz, 0.9% THD, 8 Ω)

90 W/ch

◆ FM/AM tuning capability

◆ XM Satellite Radio tuning capability (using XM Mini-Tuner

and Home Dock, sold separately)

◆ SIRIUS Satellite Radio™ tuning capability (using SIRIUS

[Other models]

(1 kHz, 0.9% THD, 6 Ω)

90 W/ch

Connect tuner, sold separately)

HDMI (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or high-definition

video (includes 1080p video signal transmission) as well as

multi-channel digital audio

SCENE select function

◆ Preset SCENE templates for various situations

◆ SCENE template customizing capability

DOCK terminal

Decoders and DSP circuits

◆ DOCK terminal to connect a Yamaha iPod universal dock

(such as YDS-10, sold separately) or Bluetooth adapter (such

as YBA-10, sold separately).

◆ Proprietary Yamaha technology for the creation of multi-

channel surround sound

◆ Compressed Music Enhancer mode

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix, Discrete, DTS Neo:6,

DTS 96/24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx

decoder

◆ Neural Surround decoder

Other features

◆ YPAO (Yamaha Parametric Room Acoustic Optimizer) for

automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ DIRECT mode for high quality sound for all sources

◆ 6 additional input jacks for discrete multi-channel input

◆ OSD (on-screen display) menus that allow you to optimize

this unit to suit your individual audiovisual system

◆ Component video input/output capability

(3 COMPONENT VIDEO INs and 1 MONITOR OUT)

◆ S-video signal input/output capability

(U.S.A. and Canada models only)

◆ Virtual CINEMA DSP

◆ SILENT CINEMA^™

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Cinema and music night listening modes

◆ iPod controlling capability

◆ Remote control with preset remote control codes

◆ Zone 2 custom installation facility

◆ Bi-amplification connection capability

DTS-ES | NEO:6 | 96/24. Product “DTS” and “DTS-ES | NEO:6”

are registered trademarks of DTS, Inc.

“96/24” is a trademark of DTS, Inc.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

The XM name and related logos are registered trademarks of XM

Satellite Radio Inc.

iPod™

“iPod” is a trademark of Apple, Inc., registered in the U.S. and

other countries.

Neural Surround^™name and related logos are trademarks owned

by Neural Audio Corporation.

Bluetooth™

Bluetooth is a registered trademark of the Bluetooth SIG and is

used by Yamaha in accordance with a license agreement.

the SIRIUS dog logo, channel names and logos are trademarks of

SIRIUS Satellite Radio Inc.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

2 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting started

■ Supplied accessories

Check that you received all of the following parts.

■ Installing batteries in the remote control

❏ Remote control

❏ Batteries (2) (AAA, R03, UM-4)

❏ Optimizer microphone

❏ AM loop antenna

❏ Indoor FM antenna

■ VOLTAGE SELECTOR

(Asia and General models only)

Caution

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local voltage BEFORE

plugging the power cable into the AC wall outlet.

Improper setting of the VOLTAGE SELECTOR may

cause damage to this unit and create a potential fire

hazard.

Take off the battery compartment cover.

Insert the two supplied batteries

(AAA, R03, UM-4) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

Rotate the VOLTAGE SELECTOR clockwise or

counterclockwise to the correct position using a

straight slot screwdriver.

Voltages are as follows:

Asia model ................... 220/230–240 V AC, 50/60 Hz

General model

...................... 110/120/220/230–240 V AC, 50/60 Hz

Snap the battery compartment cover back

into place.

Notes

VOLTAGE

SELECTOR

• Change all of the batteries if you notice that the operation range

of the remote control decreases.

230-

Voltage indication

240V

• Do not use an old battery and a new one together.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote control,

the contents of the memory may be cleared. When the memory

is cleared, insert new batteries and set up the remote control

code.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound

come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, Yamaha and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

3 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick start guide

The following steps describe the easiest way to enjoy

DVD movie playback in your home theater.

Preparation: Check the items

Prepare the following items.

Front right

speaker

Video monitor

Subwoofer

Front left

speaker

❏ Speakers

Surround right

speaker

❏ Front speaker .....................................x 2

❏ Center speaker ...................................x 1

❏ Surround speaker ..............................x 4

Select magnetically shielded speakers. The

minimum required speakers are two front speakers.

The priority of the requirement of other speakers is

as follows:

Center speaker

Surroundback

right speaker

DVD player

1. Two surround speakers

2. Center speaker

Surround back left

speaker

3. One (or two) surround back speaker(s)

Surround left

speaker

❏ Active subwoofer ...................................x 1

Select an active subwoofer equipped with an RCA

input jack.

❏ Speaker cable .........................................x 7

❏ Subwoofer cable .....................................x 1

Select a monaural RCA cable.

Step 1: Set up your speakers

❏ DVD player ..............................................x 1

Select DVD player equipped with coaxial digital

audio output jack and composite video output

jack.

☞ P . 5

❏ Video monitor..........................................x 1

Select a TV monitor, video monitor or projector

equipped with a composite video input jack.

Step 2: Connect your DVD player

and other components

❏ Video cable .............................................x 2

Select an RCA composite video cable.

❏ Digital coaxial audio cable ....................x 1

☞ P . 6

Step 3: Press SCENE 1 button

☞ P. 7

Enjoy DVD playback!

4 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick start guide

Be sure to connect the left channel (L), right channel

(R), “+” (red) and “–” (black) properly.

Step 1: Set up your speakers

Front and center speakers

Place your speakers in the room and connect them to this

unit.

Loosen

Insert

Tighten

SPEAKERS

COAXIAL

OPTICAL

DVD

DTV/CBL

DVD IN1

DTV/CBL IN2

OUT

HDMI

DIGITAL INPUT

SIRIUS

DTV/CBL

DOCK

REMOTE

COMPONENT VIDEO

ANTENNA

DVD

DVR

BACK/BI-AMP

BACK

OUT

GND

MONITOR OUT

+12V

15mA MAX.

VIDEO

AC OUTLETS

SWITCHED

_U7_NB5_AL.

TRIGGER

OUT

MONITOR

OUT

MONITOR

OUT

DVR

VIDEO

DVD

DTV/CBL

DVR

DVD

DTV/CBL

CENTER

SUB

FRONT(6CH)

SB(8CH)

MD/ OUT

OUT

DVR

SURROUND WOOFER

(PLAY) CD-R (REC)

DVD

DTV/CBL

ZONE

OUT

AUDIO

MULTI CH INPUT

OUTPUT

Place your speakers and subwoofer in the

room.

Connect speaker cables to each speaker.

To the center

speaker

To the front

right speaker

To the front

left speaker

Surround and surround back speakers

Cables are colored or shaped differently, perhaps with

a stripe, groove or ridge. Connect the striped

(grooved, etc.) cable to the “+” (red) terminals of

your speaker. Connect the plain cable to the “–”

(black) terminals.

Connect each speaker cable to the

corresponding speaker terminal of this unit.

To the surround

back right

speaker

To the surround

back left speaker

To the surround To the surround

right speaker left speaker

Connect the subwoofer cable to the input

jack of the subwoofer and the SUBWOOFER

OUTPUT jack of this unit.

1 Make sure that this unit and the subwoofer are

unplugged from the AC wall outlets.

2 Twist the exposed wires of the speaker cables

together to prevent short circuits.

Subwoofer

AV receiver

3 Do not let the bare speaker wires touch each other.

4 Do not let the bare speaker wires touch any metal

part of this unit.

SUBWOOFER

OUTPUT jack

Input jack

Subwoofer cable

5 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick start guide

Step 2: Connect your DVD player

and other components

Connect the video cable to the video input

jack of your video monitor and the VIDEO

MONITOR OUT jack of this unit.

SPEAKERS

CCOOAAXXIIAALL

AV receiver

Video monitor

CCDD

DVD IN1

DTV/CBL IN2

OUT

HDMI

SIRIUS

DTV/CBL

DOCK

REMOTE

COMPONENT VIDEO

ANTENNA

DVD

DVR

SURROUND BACK/BI-AMP

SURROUND

OUT

GND

SINGLE

MONITOR OUT

+12V

15mA MAX.

VIDEO

AC OUTLETS

SWITCHED

_U7_NB5_AL.

TRIGGER

OUT

MONITOR

CENTER

SUB

WOOFER

CENTER

FRONT

FRONT(6CH)

SB(8CH)

MD/ OUT

OUT

DVR

SURROUND WOOFER

(PLAY) CD-R (REC)

DVD

DTV/CBL

ZONE

OUT

AUDIO

MULTI CH INPUT

OUTPUT

Make sure that this unit and the DVD

player are unplugged from the AC wall

outlets.

Video input

jack

Video cable

VIDEO MONITOR OUT

jack

Connect the power plug of this unit and other

components into the AC wall outlet.

Connect the digital coaxial audio cable to the

digital coaxial audio output jack of your DVD

player and the DVD DIGITAL INPUT COAXIAL

jack of this unit.

This unit is equipped with AC OUTLET(S) for the power supply

of the other components (except Korea model). See page 22 for

details.

DVD player

AV receiver

■ For further connections

•

Using the other kind of speaker

combinations

☞ P. 11

☞ P. 16

☞ P. 17

☞ P. 18

•

Connecting video components

Connecting a DVD player

Connecting a DVD recorder

Connecting a set-top box

Digital coaxial

audio output jack

Connecting a CD player

and a CD recorder/ MD recorder

☞ P. 19

•

Connecting a multi-format player

or an external decoder

Digital coaxial audio

cable

Connecting a Yamaha iPod/Bluetooth dock

DVD DIGITAL INPUT

COAXIAL jack

☞ P. 20

Connecting the REMOTE IN/OUT jacks

☞ P. 20

Connect the video cable to the composite

video output jack of your DVD player and the

DVD VIDEO jack of this unit.

Using the VIDEO AUX jacks on the front

panel

☞ P. 21

•

Connecting an FM/AM antenna

Connecting the XM Mini-Tuner Dock

☞ P. 21

DVD player

AV receiver

☞ P. 48

•

Connecting the SIRIUS Connect tuner

☞ P. 53

Composite video

output jack

Video cable

DVD VIDEO jack

6 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick start guide

■ About SCENE function

Step 3: Press SCENE 1 button

Just by pressing one SCENE button, you can turn on this

unit and recall your favorite input source and sound field

program according to the SCENE template that has been

assigned to the SCENE button. The SCENE templates are

built combinations of input sources and sound field

programs.

Check the type of the connected speakers.

If the speakers are 6 ohm speakers, set “SP IMP.” to

“6Ω MIN” before using this unit (see page 23).

If you connect a Yamaha product that has capability of the

SCENE control signals, this unit can automatically activate the

component and start playback. Refer to the instruction manual of

the DVD player for further information.

Turn on the video monitor and then set the

input source selector of the video monitor to

this unit.

■ Using the other SCENE buttons

Press SCENE 1.

This unit is turned on. “DVD Viewing” appears in the

front panel display, and this unit automatically

optimize own status for the DVD playback.

Default

SCENE

button

The name of the SCENE template

and its description

SCENE

DVD Viewing

– input source: DVD

– sound field program: STRAIGHT

For when you want to enjoy a DVD playback.

SCENE

Disc Listening

– input source: DVD

– sound field program: 7ch Stereo

For when you want to listen to a music disc from

the connected DVD player as the background

music for this room.

TV Viewing ^*1

– input source: DTV/CBL

SCENE

– sound field program: STRAIGHT

For when you want to watch a TV program.

Radio Listening ^{*2, *3, *4}

– input source: TUNER

– sound field program: 7ch Enhancer

For when you want to listen to a music program

from the FM radio station.

SCENE

The indicator on the selected SCENE button lights up while

this unit is in the SCENE mode.

Start playback of the desired DVD on your

player.

Notes

^*1You must connect a cable TV or a satellite tuner to this unit in

advance. See page 18 for details.

Rotate

VOLUME to adjust the volume.

^*2You need to connect the supplied FM and AM antennas to this

unit in advance. See page 21 for details.

^*3You must tune into the desired radio station. See pages 45 to 47

for the tuning information.

^*4To achieve the best possible reception, orient the connected

AM loop antenna, or adjust the position of the end of the

indoor FM antenna.

If you cannot find the desired situation, you can select and change

the assigned SCENE template for the SCENE buttons. See

page 30 for details.

Note

When you change the input source or sound field program, the

SCENE mode is deactivated, and the indicator on the selected

SCENE button turns off.

7 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick start guide

■ After using this unit...

What do you want to do with this

unit?

Press MAIN ZONE ON/OFF on the front

panel to set this unit to the standby mode.

■ Customizing the SCENE templates

•

Using various SCENE templates

☞ P. 30

Creating your original SCENE templates

☞ P. 33

■ Using various input sources

•

Basic controls of this unit

☞ P. 35

☞ P. 45

Enjoying FM/AM radio programs

Enjoying XM Satellite Radio programs

☞ P. 48

•

Enjoying SIRIUS Satellite Radio programs

☞ P. 53

This unit is set to the standby mode. In the standby mode,

this unit consumes a small amount of power in order to

receive infrared signals from the remote control. To turn

•

Using your iPod with this unit

☞ P. 59

☞ P. 61

Using your Bluetooth components

with this unit

on this unit from the standby mode, press MAIN ZONE

ON/OFF (or HPOWER). See page 23 for details.

■ Using various sound features

•

Using various sound field programs

☞ P. 40

Using the direct mode for

the high quality sound

☞ P. 43

Customizing the sound field programs

☞ P. 42

■ Adjusting the parameters of this unit

•

Automatically optimizing the speaker

parameters for your listening room (AUTO

SETUP)

☞ P. 26

•

Manually adjusting various parameters of

this unit

☞ P. 63

☞ P. 76

•

Setting the remote control

Adjusting the advanced parameters☞ P. 82

■ Additional features

Automatically turning off this unit

☞ P. 39

8 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Rear panel

3 4 5 6

SPEAKERS

COAXIAL

OPTICAL

DVD

DTV/CBL

DVD IN1

DTV/CBL IN2

OUT

HDMI

DIGITAL INPUT

SIRIUS

DTV/CBL

DOCK

REMOTE

COMPONENT VIDEO

ANTENNA

DVD

DVR

SURROUND BACK/BI-AMP

SURROUND

OUT

GND

SINGLE

MONITOR OUT

+12V

15mA MAX.

VIDEO

AC OUTLETS

SWITCHED

_U7_NB5_AL.

TRIGGER

OUT

MONITOR

OUT

MONITOR

OUT

DVR

VIDEO

DVD

DTV/CBL

DVR

DVD

DTV/CBL

CENTER

SUB

WOOFER

CENTER

FRONT

FRONT(6CH)

SB(8CH)

MD/ OUT

OUT

DVR

SURROUND WOOFER

(PLAY) CD-R (REC)

DVD

DTV/CBL

ZONE

OUT

AUDIO

MULTI CH INPUT

OUTPUT

9 0

D E F

(U.S.A. model)

Name

Page

HDMI jacks

DIGITAL INPUT jacks

COMPONENT VIDEO jacks

XM jack (U.S.A. and Canada models only)

SIRIUS jack

(U.S.A. and Canada models only)

DOCK terminal

Speaker terminals

VOLTAGE SELECTOR

(Asia and General models only)

REMOTE IN/OUT jacks

TRIGGER OUT jack

—

This is a control expansion jack for custom

installation.

AUDIO jacks

VIDEO jacks

MULTI CH INPUT jacks

ZONE 2 OUT jacks

SUBWOOFER OUTPUT jack

ANTENNA terminals

AC OUTLET(S)

9 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Placing speakers

The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multi-

channel audio sources.

30˚

60˚

SBR

80˚

SBL

SBR

30 cm (12 in) or more

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the

ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a

center speaker, you can do without it. Best results, however, are obtained with the full system.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround sounds.

Surround back left and right speakers (SBL and SBR)

The surround back speakers supplement the surround speakers and provide more realistic front-to-back transitions.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is

effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction

of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is

not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front

speakers. Turn it slightly toward the center of the room to reduce wall reflections.

10 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,

this unit cannot reproduce the input sources accurately.

Caution

•

Before connecting the speakers, make sure that the AC power plug is disconnected from the AC wall outlet.

Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage

this unit and/or the speakers. If the speaker wires are short-circuited, “CHECK SP WIRES” appears in the front

panel display when you turn on this unit.

•

Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the

speakers away from the monitor.

If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6Ω MIN” before using this unit. For details about the

speaker impedance setting, see page 23.

When you use single surround

back speaker, connect the

speaker to the left SURROUND

BACK terminal (SINGLE).

Surround back speakers

Surround speakers

Right

Left

Right

SPEAKERS

COAXIAL

OPTICAL

DVD

DTV/CBL

DVD IN1

DTV/CBL IN2

OUT

HDMI

DIGITAL INPUT

SIRIUS

DTV/CBL

DOCK

REMOTE

COMPONENT VIDEO

ANTENNA

DVD

DVR

SURROUND BACK/BI-AMP

SURROUND

OUT

GND

SINGLE

MONITOR OUT

+12V

15mA MAX.

VIDEO

AC OUTLETS

SWITCHED

_U7_NB5_AL.

TRIGGER

OUT

MONITOR

OUT

MONITOR

OUT

DVR

VIDEO

DVD

DTV/CBL

DVR

DVD

DTV/CBL

CENTER

SUB

WOOFER

CENTER

FRONT

FRONT(6CH)

SB(8CH)

MD/ OUT

OUT

DVR

SURROUND WOOFER

(PLAY) CD-R (REC)

DVD

DTV/CBL

ZONE

OUT

AUDIO

MULTI CH INPUT

OUTPUT

FRONT B terminals

Connect the alternative front speaker system

(FRONT B).

Center

speaker

Subwoofer

Right

Left

Front speakers

(FRONT A)

11 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

■ Before connecting to the SPEAKERS

terminal

■ Using bi-amplification connections

Caution

A speaker cord is actually a pair of insulated cables

running side by side. Cables are colored or shaped

differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red)

terminals of this unit and your speaker. Connect the plain

cable to the “–” (black) terminals.

Remove the shorting bars or bridges to separate the

LPF (low pass filter) and HPF (high pass filter)

crossovers.

This unit allows you to make bi-amplification connections

to one speaker system. Check if your speak ers support bi-

amplification.

To make the bi-amplification connections, use the FRONT

and SURROUND BACK terminals as shown below. To

activate the bi-amplification connections, set “BI-AMP”

to “ON” in “Advanced setup” (see page 82).

Remove approximately 10 mm (3/8”) of insulation

from the end of each speaker cable and then

twist the bare wires of the cable together to

prevent short circuits.

10 mm (3/8”)

Front speakers

Left

Right

■ Connecting to the FRONT A terminals

Red: positive (+)

Black: negative (–)

SURROUND BACK/BI-AMP

FRONT

SINGLE

Loosen the knob.

This unit

Insert the bare end of the speaker wire into

the hole on the terminal.

Notes

Tighten the knob to secure the wire.

• When you make the conventional connection, make sure that

the shorting bars are put into the terminals appropriately. Refer

to the instruction manuals of the speakers for details.

• When you use bi-amplification connections, you can not use

surround back speakers.

Connecting the banana plug

(except Europe, Russia, Korea, and Asia models)

The banana plug is a single-pole electrical connector

widely used to terminate speaker cables. First, tighten the

knob and then insert the banana plug connector into the

end of the corresponding terminal.

Banana plug

12 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Information on jacks and cable plugs

Connect one of the type of the audio jack(s) and/or video jack(s) that your input components are equipped with.

Audio jacks and cable plugs Video jacks and cable plugs

COMPONENT VIDEO

DIGITAL AUDIO

COAXIAL

DIGITAL AUDIO

OPTICAL

AUDIO

VIDEO

S VIDEO

(White)

(Red)

(Orange)

(Yellow)

(Red)

(Blue)

(Green)

Left and right

analog audio

cable plugs

Coaxial

digital audio

cable plug

Optical

digital

audio cable

plug

Composite

video cable

plug

S-video

cable plug

Component

video cable

plugs

■ Audio jacks

■ Video jacks

This unit has three types of audio jacks. Connection

depends on the availability of audio jacks on your other

components.

This unit has three types of video jacks. Connection

depends on the availability of input jacks on your video

monitor.

AUDIO jacks

VIDEO jacks

For conventional analog audio signals transmitted via left

and right analog audio cables. Connect red plugs to the

right jacks and white plugs to the left jacks.

For conventional composite video signals transmitted via

composite video cables.

S VIDEO jacks

DIGITAL AUDIO COAXIAL jacks

For digital audio signals transmitted via coaxial digital

audio cables.

For S-video signals, separated into the luminance (Y) and

chrominance (C) video signals transmitted on separate

wires of S-video cables.

DIGITAL AUDIO OPTICAL jacks

For digital audio signals transmitted via optical digital

audio cables.

COMPONENT VIDEO jacks

For component signals, separated into the luminance (Y)

and chrominance (P^B, PR) video signals transmitted on

separate wires of component video cables.

Notes

Video signal flow for MONITOR OUT

Output

• You can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. Optical input jacks are compatible with digital

signals with up to 96 kHz of sampling frequency.

• This unit handles digital and analog signals independently. Thus

audio signals input at the digital jacks are not output at the

analog AUDIO OUT (REC) jacks.

Input

(MONITOR OUT)

PR PB

COMPONENT

VIDEO

S VIDEO

VIDEO

Through

Video conversion ON

(see page 73)

Note

The OSD signal is not output at the DVR OUT (REC) jacks.

13 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Information on HDMI™

■ HDMI compatibility with this unit

■ HDMI jack and cable plug

Compatible

HDMI

components

HDMI

Audio signal

types

Audio signal

formats

2ch Linear PCM

2ch, 32-192 kHz,

16/20/24 bit

CD, DVD-Video,

DVD-Audio, etc.

Multi-ch Linear

PCM

8ch, 32-192 kHz,

16/20/24 bit

DVD-Audio, etc.

Bitstream

Dolby Digital, DTS DVD-Video, etc.

HDMI cable plug

This unit’s HDMI interface is based on the following

standards:

• We recommend using an HDMI cable shorter than 5 meters (16

feet) with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect

this unit to other DVI components.

•

HDMI Version 1.2a (High-Definition Multimedia

Interface Specification Version 1.2a) licensed by

HDMI Licensing, LLC.

•

HDCP (High-bandwidth Digital Content Protection

System) licensed by Digital Content Protection,

LLC.

Notes

• Do not disconnect or connect the cable or turn off the power of

the HDMI components connected to the HDMI OUT jack of

this unit while data is being transferred. Doing so may disrupt

playback or cause noise.

• Audio signals input at input jacks other than the HDMI IN DVD

or HDMI IN DTV/CBL jack of this unit cannot be digitally

output at the HDMI OUT jack.

• If you turn off the power of the video monitor connected to the

HDMI OUT jack via a DVI connection, this unit may fail to

establish the connection to the component.

Notes

• When CPPM copy-protected DVD audio is played back, video

and audio signals may not be output depending on the type of

the DVD player.

• This unit is not compatible with HDCP-incompatible HDMI or

DVI components.

• You can check the potential problem about the HDMI

connection (see page 38).

14 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Audio and video signal flow

■ Audio signal flow

■ Video signal flow

Input

Output

Input

Output

HDMI

AUDIO

COMPONENT

VIDEO

Digital output

Analog output

S VIDEO

VIDEO

Notes

Through

• 2-channel as well as multi-channel PCM, Dolby Digital and

DTS signals input at the HDMI IN DVD or HDMI IN DTV/

CBL jack can be output at the HDMI OUT jack only when

“SUPPORT AUDIO” is set to “Other” (see page 70).

• Audio signals input at the HDMI IN jacks are not output at the

AUDIO output jacks.

Video conversion ON (see page 73)

Notes

• When the all video signals are input at the HDMI,

COMPONENT VIDEO, S VIDEO and VIDEO jacks, the

priority order of the input signals is as follows:

1. HDMI

2. COMPONENT VIDEO

3. S VIDEO

4. VIDEO

• When some digital video signals are input at the HDMI IN

DVD or HDMI IN DTV/CBL jack, the video conversion

function does not work.

• Digital video signals input at the HDMI IN DVD or HDMI IN

DTV/CBL jack cannot be output from analog video output

jacks.

15 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting video components

Connect your TV (or projector) to the HDMI OUT jack,

the COMPONENT VIDEO MONITOR OUT jacks, the S

VIDEO MONITOR OUT jack or the VIDEO MONITOR

OUT jack of this unit.

Notes

• Some video monitors connected to this unit via a DVI

connection fail to recognize the HDMI audio/video signals

being input if they are in the standby mode. In this case, the

HDMI indicator flashes irregularly.

• When you connect your TV monitor or projector via HDMI

connection, the OSD does not appear. In such cases, connect the

TV monitor or projector via component, S-video or video

connection.

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

• Connect the input source components to the HDMI IN DVD or

HDMI IN DTV/CBL jack to display the video images on the

video monitor connected to the HDMI OUT jack.

You can choose to play back HDMI audio signals on this unit or

on another HDMI component connected to the HDMI OUT jack

of this unit. Use the “SUPPORT AUDIO” parameter in “SOUND

MENU” to select the component to play back HDMI audio

signals (see page 70).

COAXIAL

OPTICAL

DVD

DTV/CBL

VD IN1

OTE

DTV/CBL IN2

OUT

HDMI

DIGITAL INPUT

SIRIUS

DTV/CBL

COMPONENT VIDEO

DVD

DVR

MONITOR OUT

VIDEO

MAX.

GER

MONITOR

OUT

MONITOR

OUT

DVR

S VIDEO

DVD

DTV/CBL

DVR

DVD

DTV/CBL

CENTER

SUB

FRONT(6CH)

SB(8CH)

D/ OUT

-R (REC)

OUT

SURROUND WOOFER

DVD

DTV/CBL

DVR

ZONE 2

OUT

AUDIO

MULTI CH INPUT

OUTPUT

Component

video in

HDMI in

Video in

S-video in

TV (or projector)

indicates recommended connections

indicates alternative connections

(One for the video connection,

and one for the audio connection)

16 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting other components

• When “VIDEO CONV.” is set to “ON” (see page 73), the

converted video signals are output only at the MONITOR OUT

jacks. To record a source, make the same type of video

connections between each component.

• To make a digital connection to a component other than the

default component assigned to DIGITAL INPUT jack, select

the corresponding setting for “OPTICAL IN” or “COAXIAL

IN” in “INPUT ASSIGNMENT” (see page 71).

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

• If you connect your DVD player to both the DIGITAL INPUT

(OPTICAL) and the DIGITAL INPUT (COAXIAL) jacks,

priority is given to the signals input at the DIGITAL INPUT

(COAXIAL) jack.

Notes

• When “VIDEO CONV.” is set to “OFF” (see page 73), be sure

to make the same type of video connections as those made for

your TV (see page 16). For example, if you connected your TV

to the VIDEO MONITOR OUT jack of this unit, connect your

Category

Program

Features

CINEMA DSP processing. This program presents an image of pop, rock, or jazz live

concert. The sound field reproduces the spaciousness of a massive pavilion with an emphasis

on the vividness of vocals on the stage and solo instruments and the beats of rhythm

instruments.

Pop/Rock

MUSIC

CINEMA DSP processing. This sound field is suitable for classic and orchestral music. The

program uses data collected in a large concert hall in Munich. You can enjoy delicate and

beautiful reverberation and a majestic atmosphere.

Hall

CINEMA DSP processing. The sound field is suitable for jazz and fusion music. It uses data

collected in a famous jazz club in New York. You can enjoy clear reverberation.

Jazz

Game

CINEMA DSP processing. You can enjoy dynamic and thrilling sound effects as you play

games. The program lets you feel the depth and three-dimensional surrounding sounds of the

field where you are playing, and offers cinema-like surrounding sound effects for the scenes

of movies.

ENTERTAINMENT

CINEMA DSP processing. You can enjoy sports relays broadcast in stereo and variety shows

with a live sound environment. For sports relays, the voices of commentators and

announcers come clearly from the center; the cheers and atmosphere in the stadium spread

around within a comfortable range, and you can feel like as if you are in the stadium.

TV Sports

CINEMA DSP processing. The sound field is suitable for movies with an emphasis on

spectacular sound effects, and is a perfect fit with a wide screen. The program reproduces a

wide dynamic range from minimum sound effects to powerful sounds.

Movie Spacious

Movie Dramatic

MOVIE

CINEMA DSP processing. This sound field is also suitable for movies with an emphasis on

three-dimensional sound effects. It restrains reverberation to an moderate extent, but

reproduces sound effects and background music in a soft, three-dimensional manner with

clarity and center orientation of voices as pivots.

Downmixes multi-channel sources to 2 channel or plays back 2-channel sources as they are.

2ch Stereo

7ch Stereo

STEREO

CINEMA DSP processing. Using this program increases the listening position range. This is

a sound field suitable for background music at parties.

Select these programs to play back compression artifacts (such as the MP3 format) in

2-channel or 7-channel stereo. This program enhances your listening experience by

regenerating the missing harmonics in a compression artifact.

2ch Enhancer

7ch Enhancer

MUSIC

ENHANCER

Note

The sound field programs of this unit are recreations of real-world acoustic environments made from precise measurements taken in the

actual concert hall, music venue, movie theater, etc. Thus, you may notice variations in the strength of the reflections coming from each

direction.

40 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Sound field programs

■ Enjoying 2-channel sources using the

standard decoders

■ Using sound field programs without

surround speakers

Signals input from 2-channel sources can also be played

back on multi-channels.

(Virtual CINEMA DSP)

Virtual CINEMA DSP allows you to enjoy the CINEMA

DSP programs without surround speakers by creating

virtual speakers.

If you set “SUR. L/R SP” to “NONE” (see page 66),

Virtual CINEMA DSP is automatically activated

whenever you select a CINEMA DSP program (see

page 40).

Press AMP and then press

QSUR. DECODE

repeatedly to select a decoder.

You can select from the following decoders depending on

the type of source you are playing and your personal

preference.

Note

Decoder

Functions

Virtual CINEMA DSP will not be activated even when “SUR. L/

R SP” is set to “NONE” (see page 66) in the following cases:

– when “7ch Stereo” (see page 40) is selected.

Dolby Pro Logic processing for any

sources

Pro Logic

– when headphones are connected to the PHONES jack.

Dolby Pro Logic II processing for

movie sources

PLII Movie

PLIIx Movie

■ Enjoying multi-channel sources and

sound field programs with headphones

(SILENT CINEMA)

Dolby Pro Logic II processing for

music sources

PLII Music

PLIIx Music

SILENT CINEMA allows you to enjoy multi-channel

music or movie sound, including Dolby Digital and DTS

sources, through ordinary headphones. SILENT CINEMA

is automatically activated whenever you connect

headphones to the PHONES jack while listening to

CINEMA DSP sound field programs (except for 7ch) (see

page 40). When activated, the SILENT CINEMA

indicator lights up in the front panel display.

Dolby Pro Logic II processing for

game sources

PLII Game

PLIIx Game

DTS processing for movie sources

DTS processing for music sources

Neo:6 Cinema

Neo:6 Music

Neural Surround processing for any

sources

Neural Sur.

■ Enjoying unprocessed input sources

(Straight decoding mode)

When this unit is in the “STRAIGHT” mode, multi-

channel sources are decoded straight into the appropriate

channels without any additional effect processing. 2-

channel stereo sources are output from only the front left

and right speakers.

Press STRAIGHT (or press AMP and then

press STRAIGHT) to select “STRAIGHT”.

To deactivate the “STRAIGHT” mode, press

STRAIGHT (or press AMP and then

STRAIGHT) again so that “STRAIGHT” disappears

from the front panel display.

41 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Sound field programs

■ Editing sound fields parameters

Initial settings are indicated in bold under each parameter.

You can enjoy good quality sound with the factory default

parameters. Although you do not have to change the initial

settings, you can change some of the parameters to better

suit the input source or your listening room.

For Pop/Rock, Hall, Jazz, Game, TV Sports,

Movie Spacious and Movie Dramatic:

DSP level DSP LEVEL

Function:

Choices:

Adjusts the effect level.

MIN, MID, MAX

While listening to a source, press AMP

and then press SPARAMETER.

For 2ch Enhancer and 7ch Enhancer:

Press 8k/ nto select the desired parameter

you want to change.

Effect level EFFECT LEVEL

Function:

Choices:

Adjusts the effect level.

LOW, HIGH

Press 8l/ hto change the parameter

value.

For Pro Logic II Music and Pro Logic IIx Music:

Panorama PANORAMA

Note

Function:

Sends stereo signals to the surround

speakers as well as the front speakers for

a wraparound effect.

You cannot change parameter values when “MEMORY GUARD”

in “OPTION MENU” is set to “ON” (see page 74).

Choices:

OFF, ON

Dimension DIMENSION

Function: Gradually adjusts the sound field either

towards the front or towards the rear.

Control range: –3 (towards the rear) to +3 (towards the

front), initial setting is STD (standard).

Center width CT WIDTH

Function:

Adjusts the center image from all three

front speakers to varying degrees. A

larger value adjusts the center image

towards the front left and right speakers.

Control range: 0 (center channel sound is output only

from center speaker) to 7 (center channel

sound is output only from front left and

right speakers), initial setting is 3.

For Neo:6 Music

Center image C.IMAGE

Function:

Adjusts the front left and right channel

output relative to the center channel

more or less dominant as necessary.

Control range: 0.0 to 1.0, initial setting is 0.3.

42 En

Download from Www.Somanuals.com. All Manuals Search And Download.

USING AUDIO FEATURES

Using audio features

Enjoying high quality sound

Adjusting the speaker level

Use the DIRECT mode to enjoy the high quality sounds of

the selected source. When the DIRECT mode is activated,

this unit plays back the selected source with the least

circuitry.

You can adjust the output level of each speaker while

listening to a music source. This is also possible when

playing sources input at the MULTI CH INPUT jacks.

Note

QDIRECT

DIRECT) to select “DIRECT”.

(or press AMP and then

Press

This operation will override the level adjustments made in

“AUTO SETUP” (see page 26) and “SP LEVEL” (see page 67).

Notes

Press AMP and then press LEVEL on

the remote control and then k/ nto select

the speaker you want to adjust.

• “TONE CONTROL” and “SOUND MENU” (see page 65)

settings (except for speaker level settings) are not effective.

• The front panel display automatically dims.

Display

FRONT L

FRONT R

CENTER

SWFR

Adjusted speaker

Front left speaker

While DIRECT mode is activated, the front panel display turns on

momentarily when an operation is performed.

Front right speaker

Center speaker

Adjusting the tonal quality

Use this feature to adjust the balance of bass and treble for

the front left and right speaker channels.

Subwoofer

Surround left speaker

Surround right speaker

Surround back left speaker

Surround back right speaker

SUR. L

SUR. R

SB L

Speaker and headphone adjustments are stored independently.

Press TONE CONTROL repeatedly to

select the high-frequency response

(TREBLE) or the low-frequency response

(BASS).

SB R

• Instead of “SB L” and “SB R”, “SUR.B” is displayed if

“SUR.B L/R SP” is set to either “SMLx1” or “LRGx1”

(see page 66).

• The available speaker channels differ depending on the

setting of the speakers.

Press PROGRAM l/ hrepeatedly to

adjust the high-frequency response

(TREBLE) or the low-frequency response

(BASS).

• When the video monitor is turned on, the “SP LEVEL”

adjustment menu appears in the video monitor.

Notes

Press l/ hto adjust the speaker output

level.

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality of the

surround speakers may not match.

• TONE CONTROL is not effective when this unit is in the

DIRECT mode, or when MULTI CH is selected as the input

source.

• Press hto increase the value.

• Press lto decrease the value.

• Control range: –10 dB to +10 dB

Press LEVEL to turn off the speaker level

adjustment display.

43 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Using audio features

Selecting the night listening mode

The night listening modes are designed to improve

listenability at lower volumes or at night.

Press AMP and then NIGHT repeatedly

to select “NIGHT:CINEMA” or

“NIGHT:MUSIC”.

Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF

• Select “NIGHT:CINEMA” when watching films to

reduce the dynamic range of film soundtracks and

make dialog easier to hear at lower volumes.

• Select “NIGHT:MUSIC” when listening to music

sources to preserve ease-of-listening for all sounds.

• Select “OFF” if you do not want to use this feature.

When a night listening mode is selected, the NIGHT

indicator lights up in the front panel display.

Press l/ hto adjust the effect level while

“NIGHT:CINEMA” or “NIGHT:MUSIC” is

displayed in the front panel display.

Effect.Lvl:MID

Choices: MIN, MID, MAX

• Select “MIN” for minimum compression.

• Select “MID” for standard compression.

• Select “MAX” for maximum compression.

“NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are

stored independently.

Notes

• You cannot use the night listening modes in the following cases:

– when the DIRECT mode (see page 43) is selected.

– when the component connected to the MULTI CH INPUT

jacks is selected as the input source (see page 36).

– when headphones are connected to the PHONES jack.

• The night listening modes may vary in effectiveness depending

on the input source and surround sound settings you use.

44 En

Download from Www.Somanuals.com. All Manuals Search And Download.

FM/AM TUNING

FM/AM tuning

There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and

there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use

the automatic and manual preset tuning features to store up to 40 stations.

Automatic tuning

Manual tuning

Automatic tuning is effective when station signals are

strong and there is no interference.

If the signal received from the station you want to select is

weak, tune into it manually.

Note

Press RINPUT l/ hrepeatedly so that

“TUNER” is displayed in the front panel

display.

Manually tuning into an FM station automatically switches the

tuner to monaural reception to increase the signal quality.

Press RINPUT l/ hrepeatedly so that

“TUNER” is displayed in the front panel

display.

Press BAND to select the reception band

(FM or AM).

Press ITUNING AUTO/MAN’L so that the

AUTO indicator lights up in the front panel

display.

Press BAND to select the reception band

(FM or AM).

Lights up

Press ITUNING AUTO/MAN’L so that the

AUTO indicator disappears from the front

panel display.

AUTO

AꢀFM 88.9 MHz

No colon (:)

AꢀFM 88.9 MHz

No colon (:)

If a colon (:) appears in the front panel display,

automatic tuning is not possible. Press PRESET/

TUNING to turn the colon (:) off.

If a colon (:) appears in the front panel display,

manual tuning is not possible. Press PRESET/

TUNING to turn the colon (:) off.

GPRESET/TUNING/CH

Press l/ honce

to begin automatic tuning.

When this unit is tuned into a station, the TUNED

indicator lights up and the frequency of the received

station is shown in the front panel display.

GPRESET/TUNING/CH

l/ hto

tune into the desired station manually.

Press

Lights up

Hold down the button to continue searching.

TUNED

AꢀFM 88.9 MHz

45 En

Download from Www.Somanuals.com. All Manuals Search And Download.

FM/AM tuning

Automatic preset tuning

Manual preset tuning

You can use the automatic preset tuning feature to store

FM stations with strong signals up to 40 (A1 to E8: 8

preset station numbers in each of the 5 preset station

groups) of those stations in order. You can then recall any

preset station easily by selecting the preset station number.

You can also store up to 40 stations (A1 to E8: 8 preset

station numbers in each of the 5 preset station groups)

manually.

Tune into a station automatically or manually.

See page 45 for tuning instructions.

Press RINPUT l/ hrepeatedly so that

“TUNER” is displayed in the front panel

display.

Press HMEMORY.

The MEMORY indicator flashes in the front panel

display for approximately 30 seconds.

Press BAND to select “FM” as the

reception band.

Press A/B/C/D/E and GPRESET/

TUNING/CH l/ hrepeatedly to select a

preset station group (A1 to E8) while the

MEMORY indicator is flashing.

Check that the colon (:) appears in the front panel

display.

Press and hold HMEMORY for more than 3

seconds.

The preset station number as well as the MEMORY

and AUTO indicators flashes. After approximately 5

seconds, automatic presetting starts from the current

frequency and proceeds toward the higher

frequencies.

Flashes

MEMORY

Flashes

A3:FM 88.9 MHz

MEMORY

AUTO

Preset station Colon (:)

group and

A1:FM 88.9 MHz

Flashes

number

Press HMEMORY while the MEMORY

indicator is flashing.

The station band and frequency appear in the front

panel display with the preset station group and

number you have selected.

When automatic preset tuning is completed, the front

panel display shows the frequency of the last preset

station.

You can select the preset station group and the preset station

number where the first received station will be stored by pressing

A/B/C/D/E and then GPRESET/TUNING/CH l/ h.

TUNED

Notes

A1:FM 88.9 MHz

• Any stored station data existing under a preset station number is

cleared when you store a new station under the same preset

station number.

The displayed station has been stored as A1.

• Only FM stations with sufficient signal strength are stored

automatically by automatic preset tuning. If the station you

want to store is weak in signal strength, tune into it manually

and store it as described in “Manual preset tuning” on this page.

Notes

• Any stored station data existing under a preset station number is

cleared when you store a new station under the same preset

station number.

• The reception mode (stereo or monaural) is stored along with

the station frequency.

46 En

Download from Www.Somanuals.com. All Manuals Search And Download.

FM/AM tuning

Selecting preset stations

Exchanging preset station

You can tune into any desired station simply by selecting

the preset station group and number under which it was

stored.

You can exchange the assignments of two preset stations

with each other. The example below describes the

procedure to exchange preset station “E1” with “A5”.

Select preset station “E1” using FA/B/C/D/E

GPRESET/TUNING/CH

See “Selecting preset stations” on this page.

When performing this operation with the remote control, press

TUNER to select “TUNER” as the input source.

and

l/ h.

Press FA/B/C/D/E (or 8A-E/CAT. l/ h)

repeatedly to select the desired preset

station group (A to E).

The preset station group letter appears in the front

panel display and changes each time you press the

button.

Press and hold PRESET/TUNING for

more than 3 seconds.

“E1” and the MEMORY indicator flash in the front

panel display.

Flashes

GPRESET/TUNING/CH

PRESET/CH k/ n) to select the desired

preset station number (1 to 8).

Press

l/ h(or

MEMORY

The preset station group and number appear in the

front panel display along with the station band and

frequency.

E1:FM 88.9 MHz

Flashes

Select preset station “A5” using FA/B/C/D/

GPRESET/TUNING/CH

E and

l/ h.

E1:FM 88.9 MHz

“A5” and the MEMORY indicator flash in the front

panel display.

You can select the desired preset station number (1 to 8) directly

by pressing the numeric buttons on the remote control.

Flashes

MEMORY

A5:FM 88.9 MHz

Flashes

Press PRESET/TUNING again.

“EXCHANGE E1–A5” appears in the front panel

display and the assignments of the two preset stations

are exchanged.

47 En

Download from Www.Somanuals.com. All Manuals Search And Download.

XM SATELLITE RADIO TUNING

XM Satellite Radio tuning

XM Radio offers an extraordinary variety of commercial-free music, plus the best in premier sports, news, talk radio,

stand-up comedy, children’s and entertainment programming. XM is broadcast in superior digital audio quality from

coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan.

XM Satellite Radio online information

For U.S. customers: http://www.xmradio.com/

For Canadian customers: http://www.xmradio.ca/

Note

The XM Satellite Radio service is only available in the 48 contiguous United States (not available in Alaska and Hawaii) and Canada.

XM READY legal disclaimer

XM monthly service subscription sold separately. XM Mini-Tuner and Home Dock required (each sold separately) to receive XM

service. It is prohibited to copy, decompile, disassemble, reverse engineer, hack, manipulate or otherwise make available any

technology or software incorporated in receivers compatible with the XM Satellite Radio System. Installation costs and other fees

and taxes, including a one-time activation fee may apply. All fees and programming subject to change. Channels with frequent

explicit language are indicated with an XL. Channel blocking is available for XM radio receivers by calling 1-800-XM-RADIO (US

residents) and 1-877-GET-XMSR (Canadian residents). For a full listing of the XM commercial- free channels and advertising-

supported channels, visit lineup.xmradio.com (US residents) or xmradio.ca (Canadian residents). Subscriptions subject to Customer

Agreement available at www.xmradio.com (US residents) and www.xmradio.ca (Canadian residents). Only available in the 48

their respective owners.

Connecting the XM Mini-Tuner Dock

Connect XM Mini-Tuner and XM Mini-Tuner Dock (sold

separately) to the XM jack on the rear panel of this unit.

For details, see the operating instructions provided with

XM Mini-Tuner Dock.

To ensure optimal reception of the XM Satellite Radio signals,

the XM Mini-Tuner Dock must be placed at or near a southerly

facing window with no obstacles in the path to the sky. You can

mount it indoors or outdoors. Use the “XM RADIO SET” screen

in the video monitor (see page 75) to check the antenna reception

level and adjust the orientation of the antenna.

Note

If “CHECK ANTENNA” or “CHECK XM TUNER” appears in

the front panel display, the connection and setting of the antenna,

Home Dock, or XM Mini-Tuner may not correct (see page 88).

XM Mini-Tuner and XM Mini-Tuner Dock

(sold separately)

SIRIUS

DTV/CBL

DOCK

ANTENNA

DVR

GND

_U7_NB5_AL.

MONITOR

OUT

S VIDEO

SUB

WOOFER

CENTER

ZONE 2

OUT

OUTPUT

48 En

Download from Www.Somanuals.com. All Manuals Search And Download.

XM Satellite Radio tuning

Activating XM Satellite Radio

Basic XM Satellite Radio

operations

Once you have installed the XM Mini-Tuner Dock,

inserted the XM Mini-Tuner, connected the XM Mini-

Tuner Dock to your XM Ready home audio system, and

Press INPUT l/ hrepeatedly (or press

installed the antenna, you are ready to subscribe and begin

receiving XM programming. There are three places to find

your eight character XM Radio ID: on the XM Mini-

Tuner, on the XM Mini-Tuner package, and on XM

Channel 0. Record the Radio ID in the following eight

squares for reference.

XM) to select “XM” as the input source.

The cursor on the left of the XM indicator lights up in

the front panel display and the XM Satellite Radio

information (such as channel number, channel name,

category, artist name, or song title) for the currently

selected channel appears in the front panel display.

Lights up

MULTI CH

DVR

V-AUX

DTV/CBL

DVD

MD/CD-R CD

TUNER

SIRIUS

Note

The XM Radio ID does not use the letters “I”, “O”, “S” or “F”.

Activate your XM Satellite Radio service in the U.S. online at

http://www.xmradio.com/ or call 1-800-XM-RADIO (1-800-967-

2346). You will need a major credit card. XM will send a signal

from the satellites to activate the full channel lineup. Activation

normally takes 10 to 15 minutes, but during peak busy periods

you may need to keep your XM Ready home audio system on for

up to an hour. When you can access the full channel lineup on

your XM Ready home audio system you are done. For more

information or to subscribe in Canada, visit XM on the Web at

www.xmradio.ca or call XM’s Listener Care at 1-877-GET-

XMSR (1-877-438-9677).

001ꢀPreview

When you select “XM” as the input source, this unit

automatically recalls the previously selected channel.

Notes

• The XM Satellite Radio signals cannot be output at the

AUDIO OUT (REC) jacks.

• If a status message or an error message appears in the front

panel display or in the OSD, see the “XM Satellite Radio”

section in “Troubleshooting” on page 84 for appropriate

remedies.

Search for a channel by using one of the XM

Satellite Radio search modes.

• To select a channel from the all channel list, see

“All Channel Search mode” on page 50.

• To select a channel by category, see “Category

Search mode” on page 50.

• To select a channel from the preset channels, see

“Preset Search mode” on page 50.

• To select the desired channel directly by entering

the channel number, see “Direct Number Access

mode” on page 50.

• You can use the Neural Surround decoder to enjoy the XM HD

surround sound content of the XM Satellite Radio broadcasts in

multi-channels (see page 41).

• You can set the XM Satellite Radio preset channels (see

page 51).

• You can display the XM Satellite Radio information in the front

panel display or in the OSD (see page 52).

49 En

Download from Www.Somanuals.com. All Manuals Search And Download.

XM Satellite Radio tuning

Before performing operations, press XM to select “XM” as the

input source.

Press PRESET/TUNING/CH l/ h(or

PRESET/CH k/ n) repeatedly to change

the preset channel number (1 to 8).

■ All Channel Search mode

You can also select the preset channel number directly by

pressing the numeric buttons (1 to 8) on the remote control.

Press SEARCH MODE (or SRCH

MODE) repeatedly to select “ALL CH

SEARCH”.

■ Direct Number Access mode

Press PRESET/TUNING/CH l/ h(or

Press SRCH MODE repeatedly to select

PRESET/CH k/ n) repeatedly to search

“ALL CH SEARCH” or “CAT SEARCH”.

for a channel within all channels.

Press the numeric buttons (G) to enter the

desired three-digit channel number.

For example, to enter the number 123, press the

numeric buttons as shown below.

• You can search for a channel quickly by pressing and holding

PRESET/TUNING/CH l/ h(or PRESET/CH k/ n).

• To display the XM Radio ID number displayed in the front

panel display, select channel “0”.

■ Category Search mode

Press SEARCH MODE (or SRCH

The display changes as follows.

MODE) repeatedly to select “CAT SEARCH”.

Press CATEGORY (or A-E/CAT. l/ h)

repeatedly to change the channel category.

<XM> --1

Press PRESET/TUNING/CH l/ h(or

PRESET/CH k/ n) repeatedly to search

for a channel within the selected channel

category.

<XM> -12

<XM>123

You can search for a channel quickly by pressing and holding

PRESET/TUNING/CH l/ h(or PRESET/CH k/ n).

■ Preset Search mode

Prior to selecting a preset channel in the Preset Search

mode, you must preset XM Satellite Radio channels. For

details, see “Setting XM Satellite Radio preset channels”

on page 51.

• To enter a one-digit or two-digit channel number, press the

numeric buttons (G) and then press ENT to confirm the

All preset channels (A1 to E8) recalls “001 Preview” by the initial

factory setting.

input number. Instead of pressing ENT to tune into the

channel immediately, you can wait a few seconds until this unit

confirms the entered channel number.

• Pressing a button other than the numeric buttons (G) or ENT

cancels the Direct Number Access mode procedure.

Press SEARCH MODE (or SRCH

MODE) repeatedly to select “PRESET

SEARCH”.

Press CATEGORY (or A-E/CAT. l/ h)

repeatedly to change the preset channel

group (A to E).

50 En

Download from Www.Somanuals.com. All Manuals Search And Download.

XM Satellite Radio tuning

Setting XM Satellite Radio preset

channels

You can use this feature to store up to 40 XM Satellite

Radio channels (A1 to E8: 8 preset channel numbers in

each of the 5 preset channel groups). You can then recall

any preset channel easily by selecting the preset channel

group and number as described in “Preset Search mode”

on page 50.

Press CATEGORY (or 8A-E/CAT. l/ h)

repeatedly to select a preset channel group

(A to E) while the MEMORY indicator is

flashing.

The preset channel group letter appears in the front

panel display.

Flashes

MEMORY

Search for a channel you want to set as a

preset channel by using one of the XM

Satellite Radio search modes.

C- 043ꢀXMU

Selected preset channel group

See “Basic XM Satellite Radio operations” on

page 49 for details.

Press PRESET/TUNING/CH l/ h(or

PRESET/CH k/ n) repeatedly to select a

preset channel number (1 to 8) while the

MEMORY indicator is flashing.

The preset channel number appears in the front panel

display.

043ꢀXMU

Currently selected channel number

Flashes

Press MEMORY (or 9MEMORY).

The MEMORY indicator flashes in the front panel

display for approximately 30 seconds.

MEMORY

C5 043ꢀXMU

Selected preset channel number

MEMORY

Flashes

Press MEMORY (or 9MEMORY) to set

the selected XM Satellite Radio channel as a

preset channel while the MEMORY indicator

is flashing.

Note

You must proceed to and carry out steps 3 through 5 while

the MEMORY indicator is flashing in the front panel

display.

A colon (:) appears next to the preset channel number

for confirmation, and the MEMORY indicator turns

off in the front panel display.

C5:043ꢀXMU

Colon (:)

Note

Once you set a new preset channel, the one previously stored in

the same preset channel group and number is cleared.

51 En

Download from Www.Somanuals.com. All Manuals Search And Download.

XM Satellite Radio tuning

• The front panel display can indicate up to 14 alphanumeric

characters at once. You can set whether to display the XM

Satellite Radio information in the front panel display in a

continuous manner or by 14 alphanumeric characters at once by

using the “FL SCROLL” parameter in “OPTION MENU” (see

page 73).

• If the XM Satellite Radio information contains a character that

cannot be recognized by this unit, the character will be

displayed with a space.

Displaying the XM Satellite Radio

information

You can display the XM Satellite Radio information (such

as channel number, channel name, category, artist name,

or song title) for the currently selected channel in the front

panel display or in the OSD.

Note

• To hold the current XM Radio information, press ENTER on

the remote control while it is being displayed. Press ENTER

again to release the held information.

If a status message or an error message appears in the front panel

display or in the OSD, see the “XM Satellite Radio” section in

“Troubleshooting” on page 88 for appropriate remedies.

• When the antenna of the XM Mini-Tuner Dock cannot receive

the signals, “NO SIGNAL” appears in the front panel display.

■ Displaying the XM Satellite Radio

information in the front panel display

information in the OSD

Press INFO (or INFO) repeatedly to toggle

between the following XM Satellite Radio

information display modes.

Press DISPLAY.

The following screen is displayed in the OSD.

XM INFORMATION

Channel number/name

Channel category

ALL CH SEARCH

: 043

[1]

CHAN : XMU

[4]

[5]

[2]

CAT

: Rock

NAME : Coldplay

TITLE : Speed of sound

.(Spe / Coldplay)

[ ]/[ ]: CHANNEL

[3]

[ ]/[ ]: CATEGORY

[

Artist name/song title

[1] Search mode (see page 50)

[2] Channel category

[3] Song title

When the channel number / name is displayed:

[4] Channel number/name

[5] Artist name

[043] XMU

• To turn off the OSD, press DISPLAY again.

When the channel category is displayed:

• XM status messages also appear in the OSD.

• You can select the amount of time the XM Satellite Radio

information is displayed in the OSD by using the “OSD-

SOURCE” parameter in “OPTION MENU” (see page 73).

• To hold the XM Satellite Radio information, press ENTER

<CAT>ROCK

on the remote control while it is being displayed in the OSD.

The HOLD indicator flashes in the front panel display while

When the artist name / song title is displayed:

you are holding the XM information. Press ENTER again or

change the XM Satellite Radio channel to release the held

information.

Coldplay / Clo

52 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SIRIUS SATELLITE RADIO™ TUNING

SIRIUS Satellite Radio™ tuning

SIRIUS Satellite Radio provides over 130 channels of exclusive entertainment and 100% commercial-free music. Only

SIRIUS has more than 65 original music channels, from today's hits to R&B, oldies and classical masterpieces. From

authentic country and real bluegrass to cool jazz, hot latin, reggae, rock and many more. Best of all, it’s all 100%

commercial-free.

SIRIUS also has more than 55 channels of world-class sports, news and entertainment. Included as part of your

subscription, you get up to 16 NFL games a week, up to 40 NBA games a week and up to 40 NHL games a week. (Games

are broadcast during their respective seasons.)

Coupled with great sports news from ESPN, the SIRIUS sports offering is unrivaled. And don’t forget a host of other

great news and entertainment, like NPR, CNBC, Fox News, Radio Disney and E! Entertainment Radio. For more

information, visit http://www.sirius.com/.

SIRIUS Satellite Radio legal disclaimer

SIRIUS is available in the U.S. for subscribers with addresses in the continental U.S. and is available in Canada for subscribers with

a Canadian address. To get SIRIUS Satellite Radio, a subscription and compatible tuner and antenna are required (sold separately).

Visit sirius.com for the most complete and up-to-date channel lineup and information.

“SIRIUS” and the SIRIUS dog logo and related marks are trademarks of SIRIUS Satellite Radio Inc.

• To ensure optimal reception of the SIRIUS Satellite Radio

Connecting the SiriusConnect

tuner

Connect the SiriusConnect tuner (sold separately) to the

SIRIUS jack on the rear panel of this unit. For details, see

the operating instructions provided with the SiriusConnect

tuner.

™

signals, the antenna of the SiriusConnect tuner must be placed

at or near a window with no obstacles in the path to the sky. The

orientation of the antenna for the best reception differs

depending on the area. Refer to the instruction manuals

supplied with the SiriusConnect tuner for the installation of the

antenna.You can mount it indoors or outdoors.

• Use the “ANTENNA INFO” information in the front panel or

“SIRIUS Information” screen in the video monitor (see

page 58) to check the antenna reception level and adjust the

orientation of the antenna.

SiriusConnect tuner and the antenna

(sold separately)

• You will need to connect the SiriusConnect tuner to the AC wall

outlet.

Notes

• If “CHECK SR TUNER” or “ANTENNA ERROR” appears in

the front panel display, the connection of the SiriusConnect

tuner or antenna is incorrect. In such cases, check the

connection of the SiriusConnect tuner and the antenna (see

page 89).

SIRIUS

DTV/CBL

DOCK

ANTENNA

• If “NOT SUPPORTED” appears in the front panel display, this

unit does not support the connected SiriusConnect tuner.

To the AC wall outlet

53 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SIRIUS Satellite Radio™ tuning

Activating SIRIUS Satellite

Basic SIRIUS Satellite Radio

operations

™

Radio

™

subscription

Before using the SIRIUS Satellite feature, you need to

activate your SIRIUS Satellite Radio subscription. To

activate the subscription, you need the Sirius ID, which is

uniquely assigned to the SiriusConnect tuner. Sirius ID is

12-digit number and it appears on the package of the

SiriusConnect tuner, on the label of the SiriusConnect

tuner and when you tune into the SIRIUS Satellite Radio

Channel “0” (see below).

Press INPUT l/ h(or press SIRIUS)

to select “SIRIUS” as the input source.

The cursor on the left of the SIRIUS indicator lights

up in the front panel display and the SIRIUS Satellite

Radio information (such as channel number, channel

name, category, artist name, or song title) for the

currently selected channel appears in the front panel

display.

■ Displaying the Sirius ID of your

Lights up

SiriusConnect tuner

MULTI CH

DVR

V-AUX

DTV/CBL

DVD

MD/CD-R CD

TUNER

SIRIUS

Press SIRIUS.

184 SIRIUS Wea

Press 0 and then ENT to display the

Sirius ID of your SiriusConnect tuner.

“000 Sirius IDxxxxxxxxxxxx” (“xxxxxxxxxxxx”

indicates the 12-digit Sirius ID of your SiriusConnect

tuner) appears in the front panel display.

When you select “SIRIUS” as the input source, this unit

automatically recalls the previously selected channel.

Notes

• The SIRIUS Satellite Radio signals cannot be output at the

AUDIO OUT (REC) jacks.

• When you have not activated your subscription yet, you

can only select “184” or “000”.

To scroll the message again, press INFO (or INFO).

Write the Sirius ID below.

ID:

Search for a channel by using one of the

SIRIUS Satellite Radio search modes.

• To select a channel from the all channel list, see

“All Channel Search mode” on page 55.

• To select a channel by category, see “Category

Search mode” on page 55.

SIRIUS Satellite Radio online information

Contact for activation

URL: https//activate.siriusradio.com/

Phone: 1-888-539-SIRIUS (1-888-539-7474)

• To select a channel from the preset channels, see

“Preset Search mode” on page 55.

• To select the desired channel directly by entering

the channel number, see “Direct Number Access

mode” on page 55.

• You can set the SIRIUS Satellite Radio preset channels

(see page 56).

• You can display the SIRIUS Satellite Radio information in

the front panel display or in the OSD (see page 58).

54 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SIRIUS Satellite Radio™ tuning

■ Preset Search mode

Before performing the following operations, press

Prior to selecting a preset channel in the Preset Search

mode, you must preset SIRIUS channels. For details, see

“Setting the SIRIUS Satellite Radio™ preset channels” on

page 56.

SIRIUS.

■ All Channel Search mode

Press SEARCH MODE (or SRCH

MODE) repeatedly to select “ALL CH

SEARCH”.

Press SEARCH MODE (or SRCH

MODE) repeatedly to select “PRESET

SEARCH”.

Press PRESET/TUNING/CH l/ h(or

Press CATEGORY (or A-E/CAT. l/ h)

repeatedly to change the preset channel

group (A to E).

PRESET/CH k/ n) repeatedly to search

for a channel within all channels.

Press PRESET/TUNING/CH l/ h(or

•

You can search for a channel quickly by pressing and holding

PRESET/TUNING/CH l/ h

PRESET/CH k/ n) repeatedly to change

(or PRESET/CH k/ n).

• You can skip channels to the previous or next category by

the preset channel number (1 to 8).

pressing CATEGORY (or A-E/CAT. l/ h).

You can also select the preset channel number directly by

■ Category Search mode

pressing the numeric buttons (1 to 8) ( ).

■ Direct Number Access mode

Press SEARCH MODE (or SRCH

MODE) repeatedly to select “CAT SEARCH”.

Press SRCH MODE on the remote control

repeatedly to select “ALL CH SEARCH” or

“CAT SEARCH”.

Press CATEGORY (or A-E/CAT. l/ h)

repeatedly to change the channel category.

Press the numeric buttons ( ) to enter the

desired three-digit channel number.

Press PRESET/TUNING/CH l/ h(or

PRESET/CH k/ n) repeatedly to search

for a channel within the selected channel

category.

For example, to enter the number 123, press the

numeric buttons ( ) as shown below.

You can search for a channel quickly by pressing and holding

PRESET/TUNING/CH l/ h(or PRESET/CH k/ n).

Note

• To display the SIRIUS Radio ID (SID) number displayed in the

This unit skips the channels when this unit is All Channel Search

mode or Category Search mode in the following cases (it is not

malfunction of this unit):

– the channel is locked (see page 56).

– the channel is out of service.

front panel display, select channel “0”.

• To enter a one-digit or two-digit channel number, press the

numeric buttons ( ) on the remote control and then press

ENT to confirm the input number.

• Instead of pressing ENT to tune into the channel

immediately, you can wait a few seconds until this unit confirms

the entered channel number.

– you do not subscribe to the channel.

• Pressing a button other than the numeric buttons ( ) or ENT

cancels the Direct Number Access mode procedure.

• If the selected channel is locked, “PIN:____” appears in the

front panel display. Enter the four-digit Parental Lock code

number by using the numeric buttons ( ) or press ENT to

cancel.

55 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SIRIUS Satellite Radio™ tuning

Before performing the following operations, press

Press PRESET/TUNING/CH l/ h

SIRIUS.

(or PRESET/CH k/ n) repeatedly to select

a preset channel number (1 to 8) while the

MEMORY indicator is flashing.

The preset channel number appears in the front panel

display.

Setting the SIRIUS Satellite

Radio

™

preset channels

You can use this feature to store up to 40 SIRIUS Satellite

Radio channels (A1 to E8: 8 preset channel numbers in

each of the 5 preset channel groups). You can then recall

any preset channel easily by selecting the preset channel

group and number as described in “Preset Search mode”

on page 55.

Flashes

MEMORY

A1ꢀ023 Hair Na

Currently selected preset channel number

Search for a channel you want to set as a

preset channel by using one of the SIRIUS

Satellite Radio search modes.

See “Basic SIRIUS Satellite Radio™ operations” on

page 54 for details.

Press MEMORY (or MEMORY) to set

the selected SIRIUS Satellite Radio channel

as a preset channel while the MEMORY

indicator is flashing.

A colon (:) appears next to the preset channel number

for confirmation, and the MEMORY indicator turns

off in the front panel display.

001 SIRIUS Hit

Currently selected channel number

A1:023 Hair Na

Colon (:)

Press MEMORY (or MEMORY).

The MEMORY indicator flashes in the front panel

display for approximately 30 seconds.

Note

Once you set a new preset channel, the one previously stored in

the same preset channel group and number is cleared.

MEMORY

Setting the Parental Lock

Flashes

You can use the Parental Lock feature to limit the access

to the desired SIRIUS Satellite channels. This unit

automatically skips the locked channels when this unit is

in the All Channel Search mode or Category Search mode

Note

You must proceed to and carry out steps 3 through 5 while

the MEMORY indicator is flashing in the front panel

display.

and you search a channel by pressing PRESET/

TUNING/CH l/ h(or PRESET/CH k/ n).

Press CATEGORY (or A-E/CAT. l/ h)

repeatedly to select a preset channel group

(A to E) while the MEMORY indicator is

flashing.

■ Setting the code number and the locked

channels

Use this feature to set the Parental Lock code number

(PIN) and select the channels to be locked.

The preset channel group letter appears in the front

panel display.

Press AMP on the remote control and then

Flashes

press MENU to display.

MEMORY

Press nto select “MANUAL SETUP” and

then press ENTER.

A-ꢀꢀ023 Hair N

Currently selected preset channel group

56 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SIRIUS Satellite Radio™ tuning

Note

Press nrepeatedly to select “OPTION

MENU” and then press ENTER.

In the SIRIUS Satellite Radio channel list screen, this unit

outputs the sound of the selected channel even if the channel

is locked. Only the first eight characters of each channel

name are displayed in the list.

Press k/ nrepeatedly to select “G)SIRIUS

SET” and then press ENTER.

The following menu screen appears.

10 Press ENTER to lock the selected

channel.

3 OPTION MENU

Check mark appears before the selected channel.

G)SIRIUSꢀSET

. PARENTAL LOCK

When you select the locked channel and press ENTER,

this unit unlocks the selected channel.

[ ]/[ ]:Up/Down

[p]/[[]:Select

11 Repeat steps 9 and 10 to lock the channels

you want.

Press nrepeatedly to select “PARENTAL

LOCK” and then press ENTER.

“NEW PIN:0000” appears.

12 Press RETURN repeatedly to exit from the

“PARENTAL LOCK” screen.

PARENTAL LOCK

NEWꢀPIN:0000

13 Press MENU to exit from the setup menu.

This unit is tuned into the last channel you select in

the “PARENTAL LOCK” screen. If the channel is

locked, this unit is tuned into “184 SIRIUS Weather

& Emergency” or “000 Sirius IDxxxxxxxxxxxx”

(“xxxxxxxxxxxx” indicates the Sirius ID of your

SiriusConnect tuner).

[0] [9]:NUMBER

[ENT]:ENTER

Note

If a SiriusConnect tuner is not connected to this unit, “Not

Available” appears.

If you forget or want to change the Parental lock code number,

use “SSR PIN” in “ADVANCED SETUP” to reset the Parental

Lock code number.

If the Parental Lock code number is already set, “PIN:___”

appears instead of “NEW PIN:0000”. Refer to step 8 and

then proceed the operations.

■ Tuning into the locked channels

You can tune into the locked channels by the Direct

number access mode or preset channel mode. When you

tune into the locked channel, following message appears

in the front panel display. Enter the code number you set

for the Parental Lock feature by using the numeric buttons

Enter the desired 4-digit code number by

using the numeric buttons ( ).

(

) or press ENT to cancel the tuning.

Press RETURN to return the previous menu level

without setting the code number.

Press ENTER to confirm the code number.

____

PIN:

“OK” appears and then “PIN:___” appears.

Enter the 4-digit code number you set at step

6 above to unlock the protection.

When the code number is correct, “OK” and then the

SIRIUS Satellite Radio channel list appears.

Note

If the entered code number is incorrect, “Wrong” appears in the

front panel display and this unit is tuned into the previously

selected channel.

Press l/ hrepeatedly to select the

desired channel category and then press k

/ nrepeatedly to select the channel you want

to lock.

57 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SIRIUS Satellite Radio™ tuning

Before performing the following operations, press

• The front panel display can indicate up to 14 alphanumeric

characters at once. You can set whether to display the SIRIUS

Satellite Radio information in the front panel display in a

continuous manner or by 14 alphanumeric characters at once by

using the “FL SCROLL” parameter in “OPTION MENU” (see

page 73).

• If the SIRIUS Satellite Radio information contains a character

that cannot be recognized by this unit, the character will be

displayed with a space.

SIRIUS.

Displaying the SIRIUS Satellite

Radio™ information

You can display the SIRIUS Satellite Radio information

(such as channel number, channel name, category, artist

name, composer name, or song title) for the currently

selected channel in the front panel display or in the OSD.

• To hold the current SIRIUS Satellite Radio information, press

ENTER while it is being displayed.

■ Displaying the SIRIUS Satellite Radio

Note

information in the OSD

If a status message or an error message appears in the front panel

display or in the OSD, see the “SIRIUS Satellite Radio” section

in “Troubleshooting” on page 89 for appropriate remedies.

Press INFO (or DISPLAY).

The following screen is displayed in the OSD.

■ Displaying the SIRIUS Satellite Radio

[5]

SIRIUSꢀInformationꢀANT:

information in the front panel display

[1]

[2]

ALLꢀCHꢀSEARCH

Press INFO (or INFO) repeatedly to toggle

between the following SIRIUS Satellite Radio

information display modes.

[6]

[7]

008:Bigꢀ'80s

:Pop

:Sanumemo

[3]

[4]

:RoadꢀtoꢀIndia

e.g.) 008 Big '80s

CHANNEL INFO

C:FrankieꢀZipper

Channel number/name

[1] Search mode (see page 54)

[2] Channel category

[3] Song title

e.g.) Pop

CATEGORY INFO

Channel category

[4] Composer name

[5] Antenna reception level

[6] Channel number/name

[7] Artist name

e.g.) Sanumemo / Roa

e.g.) Frankie Zipper

SONG INFO

Artist name / Song title

COMPOSER INFO

• To turn off the OSD, press DISPLAY again.

• SIRIUS status messages also appear in the OSD.

Composer name

• You can select the amount of time the SIRIUS Satellite Radio

information is displayed in the OSD by using the “OSD-

SOURCE” parameter in “OPTION MENU” (see page 73).

• To hold the SIRIUS Satellite Radio information, press

ANTENNA INFO

e.g.) 043

ANT:

ENTER while it is being displayed in the OSD. While this

Channel number/Antenna reception level

unit is holding the information screen, “HOLD” appears in the

OSD.

• The HOLD indicator flashes in the front panel display while

you are holding the SIRIUS information. Press ENTER

e.g.) 7ch Enhancer

DSP PROG. INFO

again or change the SIRIUS Satellite Radio channel to release

the held information. When an information is unavailable,

“––––” appears.

Sound field program

Back to “CHANNEL INFO”

58 En

Download from Www.Somanuals.com. All Manuals Search And Download.

USING IPOD™

Using iPod™

Once you have stationed your iPod in a Yamaha iPod universal dock (such as YDS-10, sold separately) connected to the

DOCK terminal of this unit (see page 20), you can enjoy playback of your iPod using the supplied remote control. You

can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression artifacts

(such as the MP3 format) stored on your iPod (see page 20).

Notes

• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.

• Some features may not be compatible depending on the model or the software version of your iPod.

• For a complete list of status messages that appear in the front panel display and in the OSD, see the “iPod” section in

“Troubleshooting” on page 91.

• Once your iPod is stationed in a Yamaha iPod universal dock, this unit begins signal transmission with your iPod.

• Once the connection between your iPod and this unit is complete, “iPod connected” appears in the front panel display and the DOCK

indicator lights up in the front panel display.

• Only the analog audio and video signals of your iPod are input at the DOCK terminal, and the analog audio signals can be output at the

analog AUDIO OUT (REC) jacks for recording.

• Your iPod battery is automatically charged when your iPod is stationed in a Yamaha iPod universal dock connected to the DOCK

terminal of this unit as long as this unit is turned on.

Controlling iPod™

You can control your iPod when “V-AUX” is selected as the input source. The operations of your iPod can be done with

the aid of the OSD of this unit (menu browse mode) or without it (simple remote mode).

■ Remote control operation

■ Controlling iPod in the simple remote

mode

You can perform the basic operations of your iPod (play,

stop, skip, etc.) using the supplied remote control without

the aid of the OSD of this unit.

Before performing the following operations,

press V-AUX/DOCK.

Button

Function

ENTER

Subsequent menu

Menu up

• You can view the photos or video clips stored on your iPod

(some models only).

• Operations can be also done with the controls on your iPod.

Menu down

Previous menu

Subsequent menu

0 ll

Search backward (Press and hold)

Search forward (Press and hold)

Skip backward

Skip forward

Stop

Pause (Menu browse mode)

Play/Pause (Simple remote mode)

Play (Menu browse mode)

Play/Pause (Simple remote mode)

DISPLAY

Previous menu

Display

59 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Using iPod™

Shuffle Shuffle

Use this feature to set this unit to play songs or albums in

random order.

■ Controlling iPod in the menu browse

mode

You can perform the advanced operations of your iPod

using the supplied remote control when you connect this

unit and a monitor using the S VIDEO or VIDEO

connection. You can browse the songs stored on your iPod

in the OSD. Further, you can change or adjust settings for

your iPod to suit your personal preferences.

Choices: Off, Songs, Albums

•

Select “Off”to deactivate this feature.

Select “Songs” to set this unit to play songs in random

order.

•

Select “Albums” to set this unit to play albums in

random order.

• The name of the song being played also appears in the front

panel display according to the “FL SCROLL” parameter in

“OPTION MENU” (see page 73).

When “Shuffle” is set to a setting other than “Off ”, “

in the top right corner while songs or albums are being shuffled.

” appears

• You can select the amount of time the iPod menu and play

information is displayed in the OSD by using the “OSD-

SOURCE” in “OPTION MENU” (see page 73)

Repeat Repeat

Use this feature to set this unit to repeat one song or a

sequence of songs.

Choices: Off, One, All

Notes

•

Select “Off”to deactivate this feature.

Select “One” to set this unit to repeat one song.

Select “All” to set this unit to repeat a sequence of

songs.

• Operations cannot be done with the controls on your iPod.

• The Yamaha logo appears in the display window of your iPod.

• There are some characters that cannot be displayed in the front

panel display or in the OSD of this unit. Those characters are

replaced with underscores “_”.

• The “Settings” parameters can be changed or adjusted only in

When “Repeat” is set to a setting other than “Off ”, “ ” or “

”

All

the OSD. Press ENTER repeatedly to toggle between the

appears in the top right corner while one song or a sequence of

songs are being repeated.

“Settings” parameter settings.

• You cannot browse the photos or video clips stored on your

iPod in the OSD. Use the simple remote mode to enjoy

watching the photos or video clips stored on your iPod.

■ The function of the play information

display

Press V-AUX/DOCK and then

[1]

[7]

[8]

DISPLAY.

iPodꢀꢀꢀꢀꢀ[Play]ꢀꢀꢀꢀ

All

The following display appears in the OSD.

[2]

[3]

[4]

ꢀ1ꢀ/ꢀ9ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀꢀFrankieꢀZipperꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀꢀMade-to-orderꢀꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀꢀRoadꢀtoꢀIndiaꢀꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀꢀ||;;;;;;;;;;;;;;;;;;ꢀꢀ

ꢀꢀ0:51ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ-7:44ꢀꢀ

iPod

Top

[9]

Playlists

Artists

Albums

Songs

Genres

[5]

[6]

Composers

Settings

[10]

[1] Playback status

[2] Track number/total tracks

[3] Artist name

Press k/ n / l/ hto navigate the iPod

menu and then press ENTER to begin

playback of the selected song.

Choices: Playlists (playlists), Artists (artists), Albums

(albums), Songs (songs), Genres (genres),

Composers (composers), Settings (settings)

• Playlists > Songs

[4] Song title

[5] Progress bar

• Artists > Albums > Songs

• Albums > Songs

• Songs

[6] Elapsed time

[7] Shuffle and repeat icons

• Genres > Artists > Albums > Songs

• Composers > Albums > Songs

• Settings > Shuffle, Repeat

[8]

(playback),

(pausing),

(search

forward) and

(search backward)

[9] Name of the album

[10] Remaining time

60 En

Download from Www.Somanuals.com. All Manuals Search And Download.

USING BLUETOOTH™ COMPONENTS

Using Bluetooth™ components

You can connect a Yamaha Bluetooth adapter (such as YBA-10, sold separately) to the DOCK terminal of this unit and

enjoy the music contents stored in your Bluetooth component (such as a portable music player) without wiring between

this unit and the Bluetooth component. You need to perform “pairing” the connected Bluetooth adapter and your

Bluetooth component in advance.

Note

Pairing the Bluetooth™ adapter

and your Bluetooth™ component

If the Bluetooth adapter is not connected to the DOCK

terminal of this unit, “No BT adapter” appears in the front

panel display.

Pairing must be performed when using a Bluetooth

component with the Bluetooth adapter connected to this

unit for the first time or if the pairing data has been

deleted. “Pairing” refers to the operation of registering a

Bluetooth component for Bluetooth communications.

Check that the Bluetooth component detects

the Bluetooth adapter.

If the Bluetooth component detects the Bluetooth

adapter, “YBA-10 YAMAHA” (example) appears in

the Bluetooth device list.

• You only need the pairing operation for the first time that you

use the Bluetooth component with the Bluetooth adapter.

• Pairing requires operations on this unit and on the other

component with which Bluetooth communications are to be

established. If necessary, refer to the other component’s

operating instructions.

Select the Bluetooth adapter in the Bluetooth

device list and then enter the pass key

“0000” on the Bluetooth component.

When the pairing procedure is successful,

There are two pairing methods: pairing by using “START

PAIRING” in “SET MENU” and quick pairing.

“Completed” appears in the front panel display.

Note

■ Pairing by using “SET MENU”

Use this feature to perform pairing with the video monitor.

Select “START PAIRING” in “INPUT MENU”. See

page 75 for details.

The Yamaha Bluetooth adapter can be paired with up to eight

Bluetooth components. When pairing is conducted successfully

with a ninth component and the pairing data is registered, the

pairing data for the least recently used other component is

cleared.

■ Quick pairing

Playback of the Bluetooth™

component

To ensure security, a time limit of 8 minutes is set for the

pairing operation. You are recommended to read and fully

understand all the instructions before starting.

Press INPUT l/ hrepeatedly (or press

V-AUX/DOCK) to select “V-AUX” as the

Press INPUT l/ hrepeatedly (or press

input source.

V-AUX/DOCK) to select “V-AUX” as the

input source.

Start playback of your Bluetooth component.

When the connected Bluetooth adapter detects the

Bluetooth component, “BT connected” and the

DOCK indicator appears in the front panel display.

Turn on the Bluetooth component you want

to pair with.

EBAND

Press and hold

seconds to start pairing.

(or BAND) for 3

• When you press ENTER, the connected Bluetooth adapter

searches and connect to the last connected Bluetooth

component. If the Bluetooth adapter cannot find the Bluetooth

component, “Not found” appears in the front panel display.

• To disconnect the Bluetooth adapter from the Bluetooth

Once the Bluetooth adapter starts pairing,

“Searching...” appears for a moment. While the

Bluetooth adapter is in the pairing mode, DOCK

indicator flashes in the front panel display.

component, press RETURN.

EBAND

(or BAND) again.

To cancel the pairing, press

61 En

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Recording

Recording adjustments and other operations are performed from the recording components. Refer to the operating

instructions for those components.

Notes

• When this unit is set to the standby mode, you cannot record between other components connected to this unit.

• TONE CONTROL (see page 43) and VOLUME settings, speaker levels (see page 43) and the sound field programs (see page 40) do

not affect recorded material.

• The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded.

• The XM Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks.

• The SIRIUS Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks.

• Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if

your source component is connected to provide only digital signals, you cannot record the source.

• S-video and composite video signals pass independently through the video circuits of this unit. Therefore, when recording or dubbing

video signals input from a video source component that provides only an S-video or a composite video signal, you can record only an

S-video or a composite video signal on your DVD recorder.

• A given input source is not output on the same OUT (REC) channel.

• The analog audio signals input at the DOCK terminal can be output at the analog AUDIO OUT (REC) jacks for recording.

• Once you have connected a recording component to this unit, keep the component turned on while using this unit. If the component is

turned off, this unit may distort the sound from other components.

• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright

laws.

Do a test recording before you start an actual recording.

If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture

itself may be disturbed due to those signals.

Turn on all the connected components.

Start playback on the selected source

component or select a broadcast station.

Press INPUT l/ hrepeatedly (or press

one of the input selector buttons (4)) to

select the source component you want to

record from.

Start recording on the recording component.

62 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this

unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening

environment.

■ Auto setup AUTO SETUP

Use this feature to automatically adjust speaker and system parameters (see page 26).

■ Manual setup MANUAL SETUP

Use this feature to manually adjust speaker and system parameters.

Sound menu 1 SOUND MENU

Parameter

Features

Page

Selects the size of each speaker, the speakers for low-frequency signal output, and the

crossover frequency, and the location of the front speakers connected to the FRONT B

terminals.

A)SPEAKER SET

Adjusts the output level of each speaker.

B)SP LEVEL

Adjusts the delay time of each speaker.

C)SP DISTANCE

D)CENTER GEQ

E)LFE LEVEL

F)DYNAMIC RANGE

G)AUDIO SET

Adjusts the tonal quality of the center speaker.

Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.

Adjusts the dynamic range of Dolby Digital or DTS signals.

Adjusts the muting level, audio delay, maximum volume level and initial volume level.

Selects whether to play back HDMI audio signals on this unit or on another HDMI

component connected to the HDMI OUT jack.

H)HDMI SET

Use this feature to enjoy 6.1/7.1-channel playback for multi-channel sources using the

Dolby Pro Logic IIx, Dolby Digital EX, or DTS-ES decoders by using the connected

surround back speakers.

I)EXTD SUR.

Input menu 2 INPUT MENU

Parameter

Features

Assigns the input jacks of this unit according to the component to be used.

Changes the name of the input source.

Page

A)INPUT ASSIGNMENT

B)INPUT RENAME

C)VOLUME TRIM

Adjusts the output volume of each input source.

Selects the decoder mode for the sources connected to the DIGITAL INPUT jacks on the

rear panel of this unit.

D)DECODER MODE

E)MULTI CH SET

Selects the video source played in the background of the sources input from the MULTI CH

INPUT jacks.

63 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

Option menu 3 OPTION MENU

Parameter

Features

Page

Adjusts the brightness of the front panel display and the way in which the XM and iPod

information is displayed.

A)DISPLAY SET

B)MEMORY GUARD

C)AUDIO SELECT

D)PARAM. INI

Locks sound field program parameters and other “SET MENU” settings.

Designates the default audio input jack select setting for the input sources connected to the

DIGITAL INPUT jacks when you turn on the power of this unit.

Initializes the parameters of a group of sound field programs.

Pair the connected Yamaha Bluetooth adapter (such as YBA-10, sold separately) with a

Bluetooth component (see page 61).

E)BLUETOOTH SET

F)XM RADIO SET

G)SIRIUS SET

Displays the current reception level of the XM Satellite Radio signals.

Sets the SIRIUS Parental Lock code number and the channel lock configuration (see

page 56).

Note

The “XM RADIO SET” and “SIRIUS SET” parameters are only applicable to the U.S.A. and Canada models.

■ Signal information SIGNAL INFO

Use this feature to check audio signal information (see page 38).

Using SET MENU

Use the remote control to access and adjust each

parameter.

Press ENTER to enter “MANUAL SETUP”.

The “MANUAL SETUP” display appears in the

OSD.

;MANUAL SETUP

You can change the “SET MENU” parameters while this unit is

. 1 SOUND MENU

2 INPUT MENU

3 OPTION MENU

reproducing sound.

Press AMP and then press MENU to

enter “SET MENU”.

[ ]/[ ]:Up/Down

[ENTER]:Enter

The top “SET MENU” display appears in the OSD.

Press k/ n/ l/ hand ENTER to select

and change the parameter.

SET MENU

TOPAMENU

• Press 8k/ nto select the desired menu or

parameter.

• Press 8l/ hto change the parameter value.

. ;AUTO SETUP

.A;MANUAL SETUP

;SIGNAL INFO

[ ]/[ ]:Up/Down

[ENTER]:Enter

• Press ENTER to enter the selected menu or to

confirm the parameter.

• Press RETURN to return to the previous menu

Press k/ nto select “MANUAL SETUP”.

level.

Press MENU to exit from “SET MENU”.

SET MENU

TOPAMENU

;AUTO SETUP

.A;MANUAL SETUP

;SIGNAL INFO

[ ]/[ ]:Up/Down

[ENTER]:Enter

64 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

Woofer section of a speaker is 16 cm (6.5 in) or larger:

large

1 SOUND MENU

Use this menu to manually adjust any speaker settings or

compensate for video signal processing delays when using

LCD monitors or projectors.

Woofer section of a speaker is smaller than 16 cm

(6.5 in): small

Front speakers FRONT SP

Choices: SMALL, LARGE

;MANUAL SETUP

1 SOUND MENU

;MANUAL SETUP

1 SOUND MENU

1/2

2/2

. A)SPEAKER SET

B)SP LEVEL

C)SP DISTANCE

D)CENTER GEQ

E)LFE LEVEL

[ ]/[ ]:Up/Down

[ENTER]:Enter

. F)DYNAMIC RANGE

G)AUDIO SET

H)HDMI SET

1 SOUND MENU

I)EXTD SUR.

A)SPEAKER SET

FRONT SP

[ ]/[ ]:Up/Down

[ENTER]:Enter

■ Speaker settings A)SPEAKER SET

Use this feature to manually adjust any speaker settings.

SMALL >LARGE

FRONT B speaker setting FRONT B

Use this feature to select the location of the front speakers

connected to the FRONT B terminals.

Choices: FRONT, ZONE B

When the front speakers are large

Select “LARGE” (large).

When the front speakers are small

Select “SMALL” (small).

1 SOUND MENU

Note

A)SPEAKER SET

When “LFE/BASS OUT” is set to “FRONT” (see page 66), you

can select only “LARGE” in “FRONT SP”. If the value of

“FRONT SP” is set to a setting other than “LARGE” in advance,

this unit automatically changes the value to “LARGE”.

FRONT B;;;;FRONT

[ ]/[ ]:Up/Down

[ ]/[ ]:Select

[

Center speaker CENTER SP

Choices: NONE, SML, LRG

•

Select “FRONT” to turn on or off SPEAKERS A and B

when the speakers connected to the FRONT B

terminals are set in the main zone.

Select “ZONE B” if the speakers connected to the

FRONT B terminals are set in another zone. If

SPEAKERS A is turned off and SPEAKERS B is

turned on, all the speakers including the subwoofer in

the main zone are muted and this unit outputs sound at

the FRONT B terminals only.

1 SOUND MENU

A)SPEAKER SET

CENTER SP

NONE >SML LRG

Notes

When the center speaker is large

Select “LRG” (large).

• If you connect headphones to the PHONES jack of this unit, the

sound is output from both headphones and the FRONT B

terminals when “FRONT B” is set to “ZONE B”.

• If a DSP program is selected when “FRONT B” is set to

“ZONE B”, this unit automatically enters the Virtual CINEMA

DSP mode (see page 41).

When the center speaker is small

Select “SML” (small).

When you do not use the center speaker

Select “NONE” (none). The center channel signals are

directed to the front left and right speakers.

65 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

Surround left/right speakers SUR. L/R SP

Choices: NONE, SML, LRG

LFE Bass out LFE/BASS OUT

Use this feature to select the speakers that output the LFE

(low-frequency effect) and the low-frequency signals.

Choices: SWFR, FRNT, BOTH

1 SOUND MENU

A)SPEAKER SET

SUR. L/R SP

1 SOUND MENU

A)SPEAKER SET

LFE/BASS OUT

NONE >SML LRG

SWFR FRNT>BOTH

When the surround speakers are large

Select “LRG” (large).

When a subwoofer is connected to this unit

and you want to get natural bass sound

Select “SWFR” (subwoofer). The LFE signals as well

as the low-frequency signals of other speakers set to

“SML” (or “SMALL”) are directed to the subwoofer.

When the surround speakers are small

Select “SML” (small).

When you do not use the surround speakers

Select “NONE” (none). This unit is set to the Virtual

CINEMA DSP mode (see page 41).

When a subwoofer is connected to this unit

and you want to get rich bass sound

Select “BOTH” (both). The low-frequency signals of

any source are output from the subwoofer. The LFE

signals as well as the low-frequency signals of other

speakers set to “SML” (or “SMALL”) are directed to

the subwoofer. The low-frequency signals of the front

left and right channels are directed to the front left and

right speakers and the subwoofer regardless of the

“FRONT SP” setting (see page 65).

Surround back left/right speakers

SUR.B L/R SP

Choices: NONE, SMLx1, SMLx2, LRGx1, LRGx2

1 SOUND MENU

A)SPEAKER SET

SUR.B L/R SP

When you do not use a subwoofer

Select “FRNT” (front). The LFE signals, the low-

frequency signals of the front left and right channels,

and the low-frequency signals of other speakers set to

“SML” (or “SMALL”) are all directed to the front left

and right speakers regardless of the “FRONT SP”

setting (see page 65).

NONE >SMLx1 SMLx2

When the surround back left and right

speakers are large

Select “LRGx2” (large x 2).

When the single surround back speaker is

large

Select “LRGx1” (large x 1).

When the surround back left and right

speakers are small

Select “SMLx2” (small x 2).

When the single surround back speaker is

small

Select “SMLx1” (small x 1).

When you do not use the surround back

speakers

Select “NONE” (none). The surround back channel

signals are directed to the surround left and right

speakers.

66 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

Crossover CROSSOVER

■ Speaker level B)SP LEVEL

Use this feature to select the crossover frequency of all the

speakers set to “SML” (or “SMALL”) in “SPEAKER

SET” (see page 65). All frequencies below the selected

frequency will be sent to the subwoofer or front speakers

depending on the setting of “LFE/BASS OUT” in

“SPEAKER SET” (see page 65).

Use this feature to manually adjust the output level of each

speaker.

Control range: –10 to +10 dB

Control step: 1 dB

Initial setting: 0 dB

Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,

120Hz, 160Hz, 200Hz

1 SOUND MENU

B)SP LEVEL

. FR.L

FR.R

1 SOUND MENU

B)SP LEVEL

1/2

2/2

__________

.SUR.L

SUR.R

SBL

1 SOUND MENU

CNTR

SWFR

A)SPEAKER SET

CROSSOVER

SBR

FREQ;;;80Hz

SP LEVEL

Adjusted speaker

Subwoofer phase SUBWOOFER PHASE

Use this feature to switch the phase of your subwoofer if

bass sounds are lacking or unclear.

Front left speaker

FR.L

Front right speaker

Center speaker

FR.R

CNTR

SWFR

SUR.L

SUR.R

SBL

Choices: NORMAL, REVERSE

Subwoofer

1 SOUND MENU

A)SPEAKER SET

SUBWOOFER PHASE

Surround left speaker

Surround right speaker

Surround back left speaker

Surround back right speaker

>NORMAL REVERSE

SBR

•

Select “NORMAL” if you do not want to reverse the

phase of your subwoofer.

Select “REVERSE” to reverse the phase of your

subwoofer.

Notes

• The available speaker channels differ depending on the setting

of the speakers.

• Instead of “SBL” and “SBR”, “SUR.B” is displayed if “SUR.B

L/R SP” is set to either “SMLx1” or “LRGx1” (see page 66).

67 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

■ Speaker distance C)SP DISTANCE

Use this feature to manually adjust the distance of each

speaker and the delay applied to the respective channel.

Ideally, each speaker should be the same distance from the

main listening position. However, this is not possible in

most home situations. Thus, a certain amount of delay

must be applied to the sound from each speaker so that all

sounds will arrive at the listening position at the same

time.

■ Center speaker equalizer D)CENTER GEQ

Use this feature to adjust the built-in 5-frequency band

(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic

equalizer for the center channel so that the tonal quality of

the center speaker matches that of the front speakers. You

can make adjustments while listening to the currently

selected source component or a test tone.

Control range: –6.0 to +6.0 dB

Control step: 0.5 dB

Initial setting: 0 dB

1 SOUND MENU

C)SP DISTANCE

1 SOUND MENU

C)SP DISTANCE

1 SOUND MENU

1/2

2/2

. UNIT;;;;;;;;feet

FRONT L;;;10.0ft

FRONT R;;;10.0ft

CENTER;;;;;8.5ft

SWFR;;;;;;10.0ft

[ ]/[ ]:Up/Down

. SUR. L;;;;;8.0ft

SUR. R;;;;;8.0ft

SB L;;;;;;;8.0ft

SB R;;;;;;;8.0ft

D)CENTER GEQ

TEST >OFF ON

. 100Hz ;;;;;;

300Hz ;;;;;;

1kHz ;;;;;;

0dB

[ ]/[ ]:Up/Down

[ ]/[ ]:Adjust

3kHz ;;;;;;

[ ]/[ ]:Adjust

10kHz ;;;;;;

[ ]/[ ]:Up/Down

[

[ ]/[ ]:Adjust

[

Unit UNIT

Choices: meters (m), feet (ft)

Initial setting:

[U.S.A. and Canada models]: feet (ft)

[Other models]: meters (m)

Test tone TEST

Use this feature to make adjustments for “CENTER GEQ”

while listening to a test tone.

Choices: OFF, ON

•

Select “OFF” to stop test tones and output the currently

selected source component.

•

Select “meters” to adjust speaker distances in meters.

Select “feet” to adjust speaker distances in feet.

•

Select “ON” to output test tones from the center and

front left speakers.

Speaker distances

Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)

Control step: 0.10 m (0.5 ft)

Initial setting:

FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft)

CENTER: 2.60 m (8.5 ft)

■ Low-frequency effect level E)LFE LEVEL

Use this feature to adjust the output level of the LFE (low-

frequency effect) channel according to the capacity of

your subwoofer or headphones. The LFE channel carries

low-frequency special effects which are only added to

certain scenes. This setting is effective when the input

signal contains the LFE channel.

SUR. L/SUR. R/SB L/SB R: 2.40 m (8.0 ft)

SP DISTANCE

FRONT L

FRONT R

CENTER

SWFR

Adjusted speaker

Front left speaker

Control range: –20 to 0 dB

Control step: 1 dB

Front right speaker

Center speaker

1 SOUND MENU

E)LFE LEVEL

Subwoofer

. SPEAKER;;;;;;0dB

HEADPHONE;;;;0dB

Surround left speaker

Surround right speaker

Surround back left speaker

Surround back right speaker

SUR. L

SUR. R

SB L

[ ]/[ ]:Up/Down

[ ]/[ ]:Adjust

[

Speaker SPEAKER

SB R

Adjusts the speaker LFE level.

Headphone HEADPHONE

Adjusts the headphone LFE level.

Notes

• The available speaker channels differ depending on the setting

of the speakers.

• Instead of “SB L” and “SB R”, “SUR.B” is displayed if

“SUR.B L/R SP” is set to either “SMLx1” or “LRGx1” (see

page 66).

Note

Depending on the settings of “LFE/BASS OUT” (see page 66),

some signals may not be output at the SUBWOOFER OUTPUT

jack.

68 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

Maximum volume MAX VOL.

■ Dynamic range F)DYNAMIC RANGE

Use this feature to select the amount of dynamic range

compression to be applied to your speakers or

headphones. This setting is effective only when this unit is

decoding Dolby Digital and DTS signals.

Use this feature to set the maximum volume level. This

feature is useful to avoid the unexpected loud sound by

mistake. For example, the original volume range is +16 dB

to –80 dB. However, when “MAX VOL.” is set to –5 dB,

the volume range becomes –5 dB to –80 dB.

1 SOUND MENU

Control range: +16 dB, +10 dB to –30 dB

Control step: 5 dB

F)DYNAMIC RANGE

. SPEAKER;;;;;;MAX

HEADPHONE;;;;MAX

Note

The “MAX VOL.” setting takes priority over the “Initial Volume”

setting. For example, if “INIT.VOL.” is set to –20 dB and “MAX

VOL.” is set to –30 dB, the volume level is automatically set to

–30 dB when you turn on the power of this unit next time.

[ ]/[ ]:Up/Down

[ ]/[ ]:Adjust

[

Speaker SPEAKER

Initial volume INIT.VOL.

Use this feature to set the volume level when the power of

this unit is turned on.

Choices: Off, MUTE, –80 dB to +16 dB

Control step: 1 dB

Adjusts the speaker compression.

Headphone HEADPHONE

Adjusts the headphone compression.

Choices: MIN, STD, MAX

•

Select “MIN” (minimum) if you regularly listen at low

volume levels.

Note

•

Select “STD” (standard) for general use.

Select “MAX” (maximum) to preserve the greatest

amount of dynamic range.

The “MAX VOL.” setting takes priority over the “INIT.VOL.”

setting.

■ Audio settings G)AUDIO SET

Use this feature to adjust the overall audio settings of this

unit.

1 SOUND MENU

G)AUDIO SET

. MUTE TYPE;;;FULL

A.DELAY;;;;;;0ms

MAX VOL.;;;+16dB

INIT.VOL.;;;;OFF

[ ]/[ ]:Up/Down

[ ]/[ ]:Select

[

Mute type MUTE TYPE

Use this feature to adjust how much the mute function

reduces the output volume (see page 37).

Choices: FULL, –20dB

•

Select “FULL” to completely mute all the audio

output.

•

Select “–20dB” to reduce the current volume by 20 dB.

Audio delay A.DELAY

Use this feature to delay the sound output and synchronize

it with the video image. This may be necessary when

using certain LCD monitors or projectors.

Control range: 0 to 160 ms

Control step: 1 ms

69 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

■ HDMI set H)HDMI SET

Use this feature to select the component to play back

HDMI audio signals.

■ Extended surround I)EXTD SUR.

1 SOUND MENU

I)EXTD SUR.

>AUTO LAST

EXTD SUR.;;;;;;AUTO

1 SOUND MENU

H)HDMI SET

[ ]/[ ]:Select

[

[ENTER]:Return

SUPPORT AUDIO:

HTR-6150

[ ]/[ ]:Select

[

[ENTER]:Return

Extended decoder select mode

Use this feature to designate the extended decoder mode

for the input sources connected to the DIGITAL INPUT

jacks when you turn on the power of this unit.

Choices: AUTO, LAST

Support audio S.AUDIO

Use this feature to select whether to play back HDMI

audio signals on this unit or on another HDMI component

connected to the HDMI OUT jack on the rear panel of this

unit.

•

Select “AUTO” if you want this unit to automatically

detect the digital audio input signal and activate the

appropriate decoder.

Choice

Functions

•

Select “LAST” if you want this unit to automatically

select the last decoder mode set for “EXTD SUR.”.

Plays back HDMI audio signals on this unit. The

HDMI audio signals input at the HDMI input

jacks of this unit are not output to the HDMI

component connected to the HDMI OUT jack on

the rear panel of this unit.

HTR-6150

Extended decoder specifying

Use this feature to enjoy 6.1/7.1-channel playback for

multi-channel sources using the Dolby Pro Logic IIx,

Dolby Digital EX, or DTS-ES decoders by using the

connected surround back speakers.

Plays back HDMI audio signals on another

HDMI component connected to the HDMI OUT

jack.

Other

Choice

Functions

Activates the optimum decoder to play back

signals in 6.1/7.1 channels when this unit

recognizes a signal flag being input.

AUTO

Notes

• This unit transmits audio and video signals input at the HDMI

input jacks to the HDMI out jack only when this unit is turned

on even if “SUPPORT AUDIO” is set to “Other”.

• Available audio/video signals depend on the specification of the

connected video monitor. Refer to the instruction manual of

each connected component.

Plays back Dolby Digital or DTS signals in

7.1 channels using the Pro Logic IIx movie

decoder.

PLIIxMovie

(when 2 surround

back speakers are

used.)

Plays back Dolby Digital or DTS signals in

6.1/7.1 channels using the Pro Logic IIx

music decoder.

PLIIxMusic

Plays back Dolby Digital or DTS signals in

6.1/7.1 channels using the Dolby Digital EX

or DTS-ES decoder.

EX/ES

Does not use any decoders to create 6.1/7.1

channels.

OFF

70 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

For HDMI jacks 1 and 2

HDMI IN [1]

2 INPUT MENU

Use this menu to reassign the input jacks, select the

decoder mode or rename the input source.

HDMI IN [2]

Choices: (1) DVD, DTV/CBL, V-AUX, DVR

(2) DVD, DTV/CBL, V-AUX, DVR

;MANUAL SETUP

2 INPUT MENU

. A)INPUT ASSIGNMENT

B)INPUT RENAME

C)VOLUME TRIM

D)DECODER MODE

E)MULTI CH SET

[ ]/[ ]:Up/Down

[ENTER]:Enter

A)INPUT ASSIGNMENT

HDMI IN

. [IN1];;; DVD

(

DVD

)

[IN2];;;DTV/CBL

(DTV/CBL )

[ ]/[ ]:Select

[

■ Input assignment

A)INPUT ASSIGNMENT

■ Input rename B)INPUT RENAME

Use this feature to change the name of the input source

that appears in the OSD and in the front panel display.

Use this feature to assign the input jacks according to the

component to be used if the initial settings of this unit do

not correspond to your needs. Change the following

parameters to reassign the respective jacks and effectively

connect more components.

2 INPUT MENU

B)INPUT RENAME

Once the input jacks are reassigned, you can select the

corresponding component by using RINPUT l/ h(or

the input selector buttons (4)).

DVD

-> DVD

[ ]/[ ]:Position

[ ]/[ ]:Chara.

[

For COAXIAL INPUT jack 1

COAXIAL IN (1)

Choices: (1) CD, MD/CD-R, DVD, DTV/CBL,

)

Press one of the input selector buttons (

V-AUX, DVR

or MULTI CH IN to select the input

source you want to change the name of.

2 INPUT MENU

SIRIUS

A)INPUT ASSIGNMENT

COAXIAL IN

DVD

MD/CD-R TUNER

. (1);;;;; DVD

(

DVD

)

MULTI CH IN

DTV/CBL

DVR

[ ]/[ ]:Select

[

V-AUX/DOCK

For OPTICAL INPUT jacks 2 and 3

OPTICAL IN (2)

OPTICAL IN (3)

Press AMP and then press l/ hon the

remote control to place the “_” (underscore)

under the space or the character you want to

edit.

Choices: (2) CD, MD/CD-R, DVD, DTV/CBL,

V-AUX, DVR

(3) CD, MD/CD-R, DVD, DTV/CBL,

V-AUX, DVR

Press k/ nto select the character you

want to use and then press l/ hto move

to the next space.

2 INPUT MENU

A)INPUT ASSIGNMENT

OPTICAL IN

. (2);;;;;DTV/CBL

(DTV/CBL )

(3);;;;;

(

Notes

)

• You can use up to 8 characters for each input.

[ ]/[ ]:Select

[

• Press nto change the character in the following order,

or press kto go in the reverse order:

A to Z, a space, 0 to 9, a space, a to z, a space, symbols (#,

*, –, +, etc.)

Note

You cannot select a specific item more than once.

71 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

DTS decoder prioritize setting

Repeat steps 1 through 3 to rename each

input source.

Choices: AUTO, DTS

•

Select “AUTO” if you want this unit to automatically

detect input signal types and select the appropriate

input mode.

Press ENTER to exit from “INPUT

RENAME”.

•

Select “DTS” when you play back a DTS-CD.

■ Multi channel input setup

E)MULTI CH SET

■ Volume trim C)VOLUME TRIM

Use this feature to adjust the output volume of each

source. This is useful if you want to balance the level of

each input source to avoid sudden changes in volume

when switching between input sources.

Choices: CD, MD/CD-R, TUNER, DVD,

DTV/CBL, V-AUX, DVR, DOCK,

MULTI CH, XM, SIRIUS

2 INPUT MENU

E)MULTI CH SET

BGV;;;;;;;;;LAST

INPUT CH;;;;;6CH

[ ]/[ ]:Select

[

Control range: –6.0 to +6.0 dB

Background Video BGV

Control step: 1.0 dB

Initial setting: 0.0 dB

Use this feature to select the video source played in the

background of the sources input at the MULTI CH INPUT

jacks.

2 INPUT MENU

C)VOLUME TRIM

Choices: DVD, DTV/CBL, V-AUX, DVR, LAST

DVD

DVD ;;;;;0.0dB

Select “LAST” to set this unit to automatically select the last

selected video source as the background video source.

[ ]/[ ]:Adjust

[RETURN]:Exit

[

Input channels INPUT CH

Use this setting to select the number of channels input

from an external decoder (see page 19).

Choices: 6CH, 8CH

Note

You can only adjust the value for DOCK when your iPod is

stationed in the Yamaha Universal Dock connected to this unit.

2 INPUT MENU

E)MULTI CH SET

■ Decoder mode D)DECODER MODE

BGV;;;;;;;;;LAST

INPUT CH;;;;;8CH

FRONT;;;;;;;;DVD

2 INPUT MENU

[ ]/[ ]:Select

[

D)DECODER MODE

>AUTO LAST

CD ;;;;AUTO

DVD ;;;;AUTO

If the connected component outputs discrete

6-channel audio signals.

Select “6CH”.

DTV/CBL ;;;;AUTO

[ ]/[ ]:Up/Down

[ ]/[ ]:Select

[

If the connected component outputs discrete

8-channel audio signals.

Decoder select mode

Select “8CH”. Also set “FRONT” (see below) to the

analog audio jacks at which the front left and right

channel signals output from the connected component

are input.

Use this feature to designate the default decoder mode for

the input sources connected to the DIGITAL INPUT jacks

when you turn on the power of this unit.

Choices: AUTO, LAST

•

Select “AUTO” if you want this unit to automatically

detect the type of input signals and select the

appropriate decoder mode.

Front left and right channels input jack FRONT

If you selected “8CH” in “INPUT CH”, you can select the

analog audio jacks at which the front left and right channel

signals output from the connected external decoder is

input.

•

Select “LAST” if you want this unit to automatically

select the last decoder mode used the connected input

source.

Choices: DVD, DTV/CBL, DVR, V-AUX

Note

“FRONT” parameter appears only when you set “INPUT CH” to

“8CH”.

72 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

Front panel display scroll FL SCROLL

3 OPTION MENU

Use this menu to adjust the optional system parameters.

Use this feature to set whether to display the information

(such as a song title or a channel name) in the front panel

display in a continuous manner or by the first 14

alphanumeric characters after scrolling all characters once

when “XM”, “SIRIUS” or “DOCK” is selected as the

input source.

;MANUAL SETUP

3 OPTION MENU

;MANUAL SETUP

3 OPTION MENU

1/2

2/2

Choices: CONT, ONCE

. A)DISPLAY SET

B)MEMORY GUARD

C)AUDIO SELECT

D)PARAM. INI

E)BLUETOOTH SET

. F)XM RADIO SET

G)SIRIUS SET

•

Select “CONT” to display the operation status in the

front panel display in a continuous manner.

Select “ONCE” to display the operation status in the

front panel display by the first 14 alphanumeric

characters after scrolling all characters once.

[ ]/[ ]:Up/Down

[ENTER]:Enter

[ ]/[ ]:Up/Down

[ENTER]:Enter

■ Display settings A)DISPLAY SET

OSD shift OSD SHIFT

Use this feature to adjust the vertical position of the OSD.

Control range: –5 (downward) to +5 (upward)

Control step: 1

3 OPTION MENU

A)DISPLAY SET

3 OPTION MENU

A)DISPLAY SET

1/2

2/2

DIMMER;;;;;;;;;0

VIDEO CONV;;;;ON

FL SCROLL;;;CONT

. OSD SHIFT;;;;;;0

OSD-SOURCE;;;30s

OSD-AMP;;;;;;30s

Initial setting: 0

•

Press lto lower the position of the OSD.

Press hto raise the position of the OSD.

[ ]/[ ]:Up/Down

[ ]/[ ]:Select

[ ]/[ ]:Up/Down

[ ]/[ ]:Select

[

Source feature OSD display time

OSD-SOURCE

Dimmer DIMMER

Use this feature to adjust the brightness of the front panel

display.

Control range: –4 to 0

Control step: 1

Use this feature to set the amount of time to display the

XM Satellite Radio information, SIRIUS Satellite Radio

information or iPod menu in the OSD after you perform a

certain operation.

Choices: ON, 10s, 30s

•

Press lto make the front panel display dimmer.

•

Select “ON” to display the OSD unceasingly during an

operation.

Select “10s” to turn off the OSD 10 seconds after you

perform a certain operation.

Select “30s” to turn off the OSD 30 seconds after you

perform a certain operation.

Press hto make the front panel display brighter.

Video conversion VIDEO CONV.

Use this feature to set whether to convert the video signals

input at the VIDEO and S VIDEO jacks.

Choices: ON, OFF

•

Select “ON” to convert composite and S-video signals

interchangeably, or to convert composite and S-video

to component video signals.

Amplifier function OSD display time

OSD-AMP

Use this feature to set the amount of time to display the

status after you perform a certain operation.

Choices: ON, 10s, 30s

•

Select “OFF” not to convert any signals.

Notes

•

Select “ON” to display the OSD constantly during an

operation.

Select “10s” to turn off the OSD 10 seconds after you

perform a certain operation.

Select “30s” to turn off the OSD 30 seconds after you

perform a certain operation.

• This unit does not convert 480 line video signals and 576 line

video signals interchangeably.

• The converted video signals are only output at the MONITOR

OUT jacks. When recording a video source, you must make the

same type of video connections between each component.

• When composite video or S-video signals from a VCR are

converted to component video signals, the picture quality may

suffer depending on your VCR.

• Unconventional signals input at the composite video or S-video

jacks cannot be converted or may be output abnormally. In such

cases, set “VIDEO CONV.” to “OFF”.

• When non-standard video signals (such as video signals from a

game console) are input, this unit may not convert the signals

even if you set “VIDEO CONV.” to “ON”.

73 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

■ Memory guard B)MEMORY GUARD

Use this feature to prevent accidental changes to DSP

program parameter values and other system settings.

Choices: OFF, ON

■ Parameter initialization D)PARAM. INI

Use this feature to set all the parameters of the sound field

programs to the initial factory settings.

Choices: NO, YES

3 OPTION MENU

D)PARAM. INI

3 OPTION MENU

B)MEMORY GUARD

>NO

YES

>OFF

[ ]/[ ]:Select

[

[ENTER]:Return

[ ]/[ ]:Select

[

•

Select “NO” to cancel the parameter initialization and

return to the previous menu screen.

•

Select “OFF” to turn off the “MEMORY GUARD”

feature.

Select “ON” to protect:

– sound field program parameters

– all “SET MENU” items

– all speaker levels

Select “YES” and press ENTER to set all the sound

field parameters to the initial factory settings.

Notes

– SCENE template parameters

• You cannot automatically revert to the previous parameter

settings once you initialize the sound field program parameters.

• You cannot separately initialize individual sound field

programs.

• You cannot initialize any sound field program groups when

“MEMORY GUARD” is set to “ON”.

Note

When “MEMORY GUARD” is set to “ON”, you cannot select

and adjust any other “SET MENU” items.

■ Audio select C)AUDIO SELECT

Use this feature to designate the default audio input jack

select setting for the input sources when you turn on the

power of this unit.

Choices: AUTO, LAST

3 OPTION MENU

C)AUDIO SELECT

>AUTO LAST

[ ]/[ ]:Select

[

•

Select “AUTO” if you want this unit to automatically

detect the type of input signals and select the

appropriate input mode.

Select “LAST” if you want this unit to automatically

select the last input mode used for the connected input

source (see page 36).

74 En

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MENU

■ Bluetooth setting E)BLUETOOTH SET

■ XM Radio setting F)XM RADIO SET

(U.S.A. and Canada models only)

3 OPTION MENU

E)BLUETOOTH SET

START PAIRING

F)XM RADIO SET

XM ANTENNA;;;95%

[ENTER]:Enter

[ENTER]:Return

Use this feature to start pairing the connected Yamaha

Bluetooth adapter (such as YBA-10, sold separately) with

your Bluetooth component. For details about the pairing,

refer to “Pairing the Bluetooth™ adapter and your

Bluetooth™ component” on page 61.

XM Radio antenna XM ANTENNA

Use this feature to check the current reception level of the

XM Satellite Radio signals. For the best reception, orient

XM Mini-Tuner so that a value of 60% or more is

displayed here.

To ensure security, a time limit of 8 minutes is set for

the pairing operation. You are recommended to read

and fully understand all the instructions before starting.

Display status: NONE, 0 to 100%

Note

“NONE” is displayed if XM Mini-Tuner Dock is not connected to

this unit. In this case, check the antenna connections (see page 48).

Press ENTER to start pairing.

The connected Bluetooth adapter starts searching

Bluetooth components. “Searching...” appears in the

video monitor.

■ SIRIUS Satellite Radio setting

G)SIRIUS SET

(U.S.A. and Canada models only)

Use this feature to set the code number for locking the

desired SIRIUS Satellite Radio channels. Refer to “Setting

the Parental Lock” on page 56 for details.

Check that the Bluetooth component detects

the Bluetooth adapter.

If the Bluetooth component the Bluetooth adapter,

“YBA-10 YAMAHA” (example) appears in the

Bluetooth device list.

3 OPTION MENU

G)SIRIUS SET

. PARENTAL LOCK

Select the Bluetooth adapter in the Bluetooth

device list and then enter the pass key

“0000” on the Bluetooth component.

Once this unit completes the pairing successfully,

“Pairing completed” appears.

[ ]/[ ]:Up/Down

[ENTER]:Select

SIRIUS Satellite Radio parental lock

PARENTAL LOCK

To cancel the pairing, press RETURN to exit from

“START PAIRING”.

Use this feature to set the code number for locking the

desired SIRIUS Satellite Radio channels. Refer to “Setting

the Parental Lock” on page 56 for details.

Press RETURN to exit from “START

PAIRING”.

Notes

• If the connected Bluetooth adapter cannot find any Bluetooth

components, “Not found” appears.

• If a Bluetooth adapter is not connected to this unit, “No

Bluetooth Adapter” appears.

75 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control features

In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha

and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code

for each input source (see page 78).

Controlling this unit, a TV, or other components

■ Controlling this unit

Press AMP to control this unit.

■ Controlling a TV

Press DTV/CBL to control your TV. To control your

TV, you must set the appropriate remote control code for

DTV/CBL (see page 78).

POWER POWER

STANDBY

SIRIUS

POWER

MUTE

POWER POWER

STANDBY

SIRIUS

POWER

MUTE

DVD

MD/CD-R TUNER

TV CH

DTV/CBL

DVR

DVD

MD/CD-R TUNER

V-AUX/DOCK

AMP

TV CH

DTV/CBL

DVR

TV VOL

TV INPUT

TV MUTE

DTV/CBL

V-AUX/DOCK

AMP

TV VOL

TV INPUT

TV MUTE

SCENE

SRCH MODE

BAND LEVEL

SCENE

TITLE

VOLUME

BAND LEVEL

SRCH

^MODEVOLUME

TITLE

ENTER

DISPLAY

RETURN

MEMORY

REC

DISPLAY

RETURN

MEMORY

REC

INFO

PROG

ENHANCER SUR. DECODE

INFO

STRAIGHT DIRECT

NIGHT

PARAMETER

PROG

ENHANCER SUR. DECODE

MULTI CH IN AUDIO SEL

SLEEP

ENT

STRAIGHT DIRECT

NIGHT

PARAMETER

MULTI CH IN AUDIO SEL

SLEEP

ENT

Notes

^*1These buttons always control this unit.

^*1These buttons always control your TV regardless of whether

These buttons control this unit only when AMP is pressed.

you press DTV/CBL or not.

Remote control

Digital TV/Cable TV

Turns on or off the power.

TV POWER

TV CH +/–

Changes the channel number.

Increases or decreases the volume

level.

TV VOL +/–

Changes the input source.

Mutes the audio output.

TV INPUT

TV MUTE

These buttons control your TV only when DTV/CBL is

pressed. For details, see the “Digital TV/Cable TV” column on

page 77.

You can control more than one TV by setting the appropriate

remote control code for any input source selector buttons other

than DTV/CBL. In such a case, you can control the buttons

highlighted above (*1 and *2) when you press the input source

selector button.

76 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control features

■ Controlling other components

Press one of the input selector buttons (4) or A to C

buttons to control othercomponents. You must set the

appropriate remote control code for each input source in

advance (see page 78). The following table shows the

function of each control button used to control other

components assigned to each input selector button. Be

advised that some buttons may not correctly operate the

selected component.

SRCH MODE

BAND LEVEL

TITLE

VOLUME

[2]

[1]

POWER POWER

STANDBY

SIRIUS

POWER

MUTE

[7]

[8]

ENTER

[3]

[4]

[5]

DVD

MD/CD-R TUNER

RETURN

DISPLAY

MEMORY

TV CH

DTV/CBL

DVR

REC

V-AUX/DOCK

AMP

TV VOL

TV INPUT

TV MUTE

INFO

PROG

ENHANCER SUR. DECODE

• The remote control has 13 modes (input areas) to control

components so that the remote control can operate up to 13

different components.

SCENE

STRAIGHT DIRECT

NIGHT

PARAMETER

[6]

MULTI CH IN AUDIO SEL

SLEEP

ENT

[9]

• When you press one of the optional component control area

buttons (A to C), you can control the desired component

without changing the input source of this unit.

DVD player/

recorder

Digital TV/

Cable TV

MD/CD

recorder

Remote control

VCR

LD player

CD player

Tuner

[1] AV POWER

[2] TITLE

Power *1

Title

Power *1

Power *2

Power *1

Band

[3] PRESET/CH k

Preset up (1-8)/

Tuning up

VCR channel up Up

VCR channel

Preset down

(1-8)/Tuning

down

PRESET/CH n

Down

down

Preset down

(A-E)

A-E/CAT. l

A-E/CAT. h

Left

Preset up

(A-E)

Right

ENTER

[4] RETURN

[5] REC

Enter

Hold

Return

Memory

Disc skip

(player)

Rec (recorder)

Rec

Rec *2

Disc skip

Play

Rec

Play

Play *2

Play

backward

Searchbackward

Search backward

Search backward Search backward Search backward Information

Search forward

Search forward Search forward

Pause Pause

Skip backward Skip backward

Search forward

Pause

Search forward Search forward

Pause *2

Pause

Skip backward

Audio program

down

Skip backward

Audio program

Skip forward

Stop

Skip forward

Stop

Skip forward *2 Skip forward

Stop *2 Stop

Skip forward

Stop

Skip forward

Stop

[6] 1-9, 0, +10

Preset stations

(1-8)

Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons

[7] MENU

[8] DISPLAY

[9] ENT

Display

Enter

Search mode

Display

Title/Index

Display

Enter

Display

Index

Display

Index

Chapter/Time

Enter

Notes

^*1This button is operational only when the original remote control supplied with the component has a POWER button.

^*2These buttons operate your DVD recorder only when you set the appropriate remote control code for DVR (see page 78).

77 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control features

Setting remote control codes

You can control other components by setting the

appropriate remote control codes. For a complete list of

available remote control codes, refer to “List of remote

control codes” at the end of this manual.

While pressing and holding one of the input

selector buttons ( ) on the remote control to

select the input area you want to set up,

press AV POWER for more than 3

seconds.

SIRIUS

Remote control code default settings

MD/CD-R TUNER

Input

source

Component

category

Default

code

Manufacturer

POWER

DVD

DTV/CBL

DVR

MD/CD-R

TUNER

DVD

Yamaha

—

5013

5001

5007

2000

—

Press for 3

seconds

V-AUX/DOCK

CD-R

While holding down

TUNER

DVD

Press the numeric buttons (0 to 9) ( ) to

enter the four-digit remote control code for

the component to be used.

When the setting succeeds, “RemoteSetup OK”

appears; however, when it does not, “RemoteSetup

NG” appears in the front panel display.

DTV/CBL

V-AUX

DVR

—

TUNER

DVR

Yamaha

5011

2011

5009

5017

5012

5009

5017

TUNER

Notes

SIRIUS

• If the manufacturer of your component has more than one code,

try each of them until you find the correct one.

• If you do not press any buttons within 30 seconds in step 2, the

setup process is canceled. If this happens, repeat the setup

procedure.

Note

You may not be able to operate your Yamaha component even if a

Yamaha remote control code is preset as listed above. In this case,

try setting another Yamaha remote control code.

78 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Using multi-zone configuration

This unit allows you to configure a multi-zone audio system. The Zone 2 feature allows you to set this unit to reproduce

separate input sources in the main zone and the second zone (Zone 2). You can control this unit from the second zone

using the supplied remote control.

Only analog signals are sent to the second zone. Any source you want to listen to in the second zone must be

connected to the analog AUDIO IN jacks of this unit.

Connecting Zone 2

You need the following additional equipment to use the multi-zone functions of this unit:

•

An infrared signal receiver in the second zone.

An infrared signal emitter in the main zone. This emitter transmits the infrared signals from the remote control via the

infrared signal receiver in the second zone to a CD player or a DVD player, etc. in the main zone.

An amplifier and speakers in the second zone.

•

• Since there are many possible ways to connect and use this unit in a multi-zone configuration, we recommend that you consult with

your nearest authorized Yamaha dealer or service center about the Zone 2 connections that best meet your requirements.

• Some Yamaha models are able to connect directly to the REMOTE jacks of this unit. If you own these products, you may not need to

use an infrared signal emitter. Up to 6 Yamaha components can be connected as shown below.

REMOTE

OUT

REMOTE

OUT

Infrared signal

receiver

Yamaha

component

Yamaha

component

This unit

■ Using the external amplifier

Connect the amplifier/receiver in the second zone and other components to this unit as follows.

From the ZONE 2 OUT jacks

Amplifier

Main zone

Second zone

(Zone 2)

Infrared signal receiver

Remote control

DVD player

This unit

Infrared signal emitter

From the REMOTE IN jacks

From the REMOTE OUT jacks

Note

To avoid unexpected noise, DO NOT USE the Zone 2 feature with CDs encoded in DTS.

79 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Using multi-zone configuration

■ Controlling Zone 2 with the front panel

Controlling Zone 2

You can select and control Zone 2 by using the control

buttons on the front panel or on the remote control. The

available operations are as follows:

Turning on Zone 2

Press ZONE CONTROL to turn on Zone 2.

•

Selecting the input source of Zone 2.

Activating the Zone 2 operation mode

Tuning into FM or AM when “TUNER” is selected as

the input source of Zone 2 (see page 45).

Tuning into XM Satellite Radio when “XM” is selected

as the input source of Zone 2 (see page 48) (U.S.A. and

Canada models only).

Tuning into SIRIUS Satellite Radio when “SIRIUS” is

selected as the input source of Zone 2 (see page 53)

(U.S.A. and Canada models only).

Enjoying music stored on your iPod stationed in a

Yamaha iPod universal dock (such as YDS-10 sold

separately) connected to the DOCK terminal of this

unit when “V-AUX” is selected as the input source

(see page 59).

Press ZONE CONTROL to control Zone 2.

The ZONE2 indicator flashes in the front panel display for

approximately 10 seconds.

•

ZONE2

Flashes

•

Enjoying music stored on your Bluetooth component

being performed “paring” operation with a Yamaha

Bluetooth adapter (such as YBA-10 sold separately)

connected to the DOCK terminal of this unit when “V-

AUX” is selected as the input source

(see page 61).

Note

You must complete each step while the ZONE2 indicator is

flashing in the front panel display. Otherwise, the Zone 2 mode is

automatically canceled and this unit returns to the normal

operation mode. In this case, repeat the Zone 2 selection

procedure.

80 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Using multi-zone configuration

■ Controlling Zone 2 with the remote

Operate the following operations after activating the Zone 2

operation mode.

control

Turning on Zone 2

Operating Zone 2

While pressing and holding

AMP, press

Press INPUT l/ hto select the desired input

source while the ZONE2 indicator is flashing in

the front panel display.

POWER.

While holding

down

•

Select “TUNER” as the input source to use the TUNER

features in Zone 2. For details about the TUNER

operations, see “FM/AM tuning” on page 45.

Select “XM” as the input source to use the XM

Satellite Radio features in Zone 2. For details about the

XM Satellite Radio operations, see “XM Satellite

Radio tuning” on page 48.

AMP

POWER

•

Operating Zone 2

•

Select “SIRIUS” as the input source to use the SIRIUS

Satellite Radio features in Zone 2. For details about the

SIRIUS Satellite Radio operations, see “SIRIUS

Satellite Radio™ tuning” on page 53.

While pressing and holding AMP, press one of

the input selector buttons ( ) to select the

desired input source of Zone 2.

•

Select “V-AUX” as the input source to use iPod

features in Zone 2. For details about the iPod

operations, see “Using iPod™” on page 59.

Select “V-AUX” as the input source to use Bluetooth

component features in Zone 2. For details about the

Bluetooth component operations, see “Using

Bluetooth™ components” on page 61.

Setting Zone 2 to the standby mode

While pressing and holding AMP, press

STANDBY to set ZONE 2 to the standby

mode.

Set Zone 2 to the standby mode

Press ZONE 2 ON/OFF to set Zone 2 to the

standby mode.

Press CSYSTEM OFF to set the main zone and Zone 2 to the

standby mode simultaneously.

81 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced setup

This unit has additional menus that are displayed in the

front panel display. The advanced setup menu offers

additional operations to adjust and customize the way this

unit operates. Change the initial settings (indicated in bold

under each parameter) to reflect the needs of your

listening environment.

■ Speaker impedance SP IMP.

(U.S.A. and Canada models only)

Use this feature to set the speaker impedance of this unit

so that it matches that of your speakers.

Choices: 8Ω MIN, 6Ω MIN

•

Select “8Ω MIN” to set the speaker impedance to 8 Ω .

Select “6Ω MIN” to set the speaker impedance to 6 Ω .

•

Notes

• Only MAIN ZONE ON/OFF, PROGRAM l/ h, and

SP IMP.

Speaker

Front (A or B)

Center

Impedance level

STRAIGHT are effective while you are using the advanced

setup menu.

• No other operations can be made while you are using the

advanced setup menu.

• The advanced setup menu is only available in the front panel

display.

The impedance of each

speaker must be 8 Ω or

higher.

8Ω MIN

Surround

Front (A or B)

Center

The impedance of each

speaker must be 6 Ω or

higher.

Press SYSTEM OFF to set this unit to the

6Ω MIN

standby mode.

Surround

Press and hold TONE CONTROL and

then press MAIN ZONE ON/OFF to turn

on this unit.

This unit turns on, and the advanced setup menu

appears in the front panel display.

■ SIRIUS Satellite Radio Parental Lock

code number reset SR PIN

Use this feature to set the code number for the SIRIUS

Satellite Radio Parental Lock feature to the initial factory

setting.

Choices: RESET, CANCEL

Press PROGRAM l/ hto select the

•

Select “RESET” to set the code number to the initial

factory setting.

Select “CANCEL” to set the code number to the initial

factory setting.

parameter you want to adjust.

The name of the selected parameter appears in the

front panel display.

Press STRAIGHT repeatedly to change

Note

the selected parameter setting.

Even if you set “SR PIN” to “RESET”, this unit does not unlock

the locked channels. The initial factory setting of the Parental

Lock code number is “0000”.

Press MAIN ZONE ON/OFF to confirm

your selection and set this unit to the

standby mode.

■ Bi-amplifier setting BI-AMP

Use this feature to activate or deactivate the bi-amplifier

function (see page 12).

The settings you made are reflected next time you turn on this

unit.

Choices: ON, OFF

•

Select “ON” if you want to activate the bi-amplifier

function. “SUR.B L/R SP” is set to “NONE”

automatically, and this unit outputs the front channel

audio signals at the SURROUND BACK/BI-AMP

speaker terminals.

•

Select “OFF” if you want to deactivate the bi-amplifier

function.

82 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced setup

■ SCENE IR code setting SCENE IR

Use this feature to output the remote control signals at the

REMOTE OUT jack automatically when this unit is in the

SCENE mode.

Choices: ON, OFF

•

Select “ON” when the component connected to the

REMOTE OUT jack is the Yamaha component and has

the capability of the SCENE control signals. This unit

automatically sends the remote control signals to the

component.

•

Select “OFF” when the component connected to the

REMOTE OUT jack is not the Yamaha component and

does not have the capability of the SCENE control

signals.

Note

If noises are output when you operate the SCENE function, set

“SCENE IR” to “OFF”.

■ Tuner frequency step TU

(Asia and General models only)

Use this feature to set the tuner frequency step according

to the frequency spacing in your area.

Choices: AM10/FM100, AM9/FM50

•

Select “AM10/FM100” for North, Central and South

America.

Select “AM9/FM50” for all other areas.

■ Initializing INIT.

Use this feature to reset all the parameters of this unit to

the initial factory settings (see page 93).

Choices: CANCEL, RESET

•

Select “CANCEL” not to reset any parameters of this

unit.

•

Select “RESET” to reset the parameters of this unit.

Notes

• This setting completely resets all the parameters of this unit

including the “SET MENU” parameters. However, the

advanced setup menu parameters will not be initialized.

• The initial factory settings are activated next time you turn on

this unit.

83 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below

or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized

Yamaha dealer or service center.

■ General

See

page

Problem

Cause

Remedy

This unit fails to turn

on or enters the

standby mode soon

after the power is

turned on.

The power cable is not connected or the

plug is not completely inserted.

Connect the power cable firmly.

—

The speaker impedance setting is

incorrect.

Set the speaker impedance to match your speakers.

The protection circuitry has been

activated.

Make sure that all speaker wire connections on this

unit and on all speakers are secure and that the wire

for each connection does not touch anything other

than its respective connection.

This unit has been exposed to a strong

external electric shock (such as lightning

or strong static electricity).

Set this unit to the standby mode, disconnect the

power cable, plug it back in after 30 seconds and then

use it normally.

—

No sound.

Incorrect input or output cable

connections.

Connect the cables properly. If the problem persists,

the cables may be defective.

13-19

No appropriate Audio input jack select has Set an appropriate Audio input jack select.

been set.

Audio input jack select is set to “HDMI”,

“COAX/OPT” or “ANALOG”.

Set Audio input jack select to “AUTO”.

Audio input jack select is set to

“ANALOG” while playing a source

encoded in Dolby Digital or DTS.

Set Audio input jack select to “AUTO” or

“COAX/OPT”.

No appropriate input source has been

selected.

Select an appropriate input source with RINPUT

l/ h(or the input selector buttons(4)).

Speaker connections are not secure.

Secure the connections.

The front speakers to be used have not

been selected properly.

Select the front speakers with MSPEAKERS.

The volume is turned down.

The sound is muted.

Turn up the volume.

—

Press JMUTE or VOLUME +/– to resume audio

output and then adjust the volume.

Signals this unit cannot reproduce are

being input from a source component,

such as a CD-ROM.

Play a source whose signals can be reproduced by this

unit.

—

The HDMI components connected to this

unit do not support the HDCP copy

protection standards.

Connect HDMI components that support the HDCP

copy protection standards.

“SUPPORT AUDIO” is set to “Other” and Set “SUPPORT AUDIO” to “HTR-6150” in

“HDMI” audio signals are not being

played back on this unit.

“MANUAL SETUP”.

84 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

See

page

Problem

Cause

Remedy

The sound suddenly

goes off.

The protection circuitry has been activated Check that the impedance setting is correct.

because of a short circuit, etc.

Check that the speaker wires are not touching each

other and then turn this unit back on.

—

The sleep timer has turned off this unit.

The sound is muted.

Turn on this unit, and play the source again.

—

Press JMUTE or VOLUME +/– to resume audio

output.

Sound is heard from

the speaker on one

side only.

Incorrect cable connections.

Connect the cables properly. If the problem persists,

the cables may be defective.

11-19

Incorrect settings in “SP LEVEL”.

Adjust the “SP LEVEL” settings.

This is not malfunction.

—

Only the center

speaker outputs

substantial sound.

When playing a monaural source with a

CINEMA DSP program, the source signal

is directed to the center channel, and the

front and surround speakers output effect

sounds.

No sound is heard

from the center

speaker.

“CENTER SP” in “SPEAKER SET” is set Set “CENTER SP” to “SML” or “LRG”.

to “NONE”.

One of the HiFi DSP programs (except for Try another sound field program.

7ch Stereo) has been selected.

No sound is heard

from the surround

speakers.

“SUR. L/R SP” in “SPEAKER SET” is

set to “NONE”.

Set “SUR. L/R SP” to “SML” or “LRG”.

This unit is in the “STRAIGHT” mode

and a monaural source is being played

back.

Press STRAIGHT so that “STRAIGHT”

disappears from the front panel display.

No sound is heard

from the surround

back speakers.

“SUR. L/R SP” in “SPEAKER SET” is

set to “NONE” and “SUR.B L/R SP” is

automatically set to “NONE”.

Set “SUR. L/R SP” and “SUR. B L/R SP” to a setting

other than “NONE”.

“SUR.B L/R SP” in “SPEAKER SET” is

set to “NONE”.

Set “SUR.B L/R SP” to a setting other than “NONE”.

No sound from the

center, surround or

surround back

speakers when the

FRONT B speakers

are activated.

“FRONT B” in “SPEAKER SET” is set to Set “FRONT B” to “FRONT”.

“ZONE B”.

No sound is heard

from the subwoofer.

“LFE/BASS OUT” in “SPEAKER SET”

is set to “FRNT” when a Dolby Digital or

DTS signal is being played.

Set “LFE/BASS OUT” to “SWFR” or “BOTH”.

—

“LFE/BASS OUT” in “SPEAKER SET”

is set to “SWFR” or “FRNT” when a 2-

channel source is being played.

Set “LFE/BASS OUT” to “SWFR” or “BOTH”.

This is not malfunction.

The source does not contain low-

frequency bass signals.

85 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

See

page

Problem

Cause

Remedy

Dolby Digital or DTS

sources cannot be

played. (Dolby Digital

or DTS indicator in

the front panel

The connected component is not set to

output Dolby Digital or DTS digital

signals.

Make an appropriate setting following the operating

instructions for your component.

—

Audio input jack select is set to

“ANALOG”.

Set Audio input jack select to “AUTO”.

display does not light

up.)

A humming sound is

heard.

Incorrect cable connections.

Connect the audio cables firmly. If the problem

persists, the cables may be defective.

—

The volume level

cannot be increased,

or the sound is

distorted.

You are attempting to set the volume level Adjust “MAX VOL.” setting.

higher than the maximum volume level.

The component connected to the AUDIO

OUT (REC) jacks of this unit is turned

off.

Turn on the power of the component.

The sound effect

cannot be recorded.

It is not possible to record the sound effect This is not malfunction.

with a recording component.

—

A source cannot be

recorded by an

analog component

connected to the

AUDIO OUT (REC)

jacks.

The source component is not connected to Connect the source component to the analog AUDIO

15, 19

the analog AUDIO IN jacks of this unit.

IN jacks.

The sound field

“MEMORY GUARD” in “OPTION

Set “MEMORY GUARD” to “OFF”.

—

parameters and some MENU” is set to “ON”.

other settings of this

unit cannot be

changed.

This unit does not

operate properly.

The internal microcomputer has been

Disconnect the power cable from the AC wall outlet

and then plug it in again after about 30 seconds.

frozen by an external electric shock (such

as lightning or excessive static electricity)

or by a power supply with low voltage.

No sound is heard

from the connected

HDMI component.

The HDMI component does not accept the Convert the multi-channel audio signals to the 2-

—

multi-channel audio signals.

channel audio signals at the source component such

as a DVD player.

“CHECK SP WIRES”

appears in the front

panel display.

Speaker cables are short-circuited.

Make sure all speaker cables are connected correctly.

There is noise

interference from

digital or radio

This unit is too close to the digital or high- Move this unit further away from such equipment.

frequency equipment.

The picture is

disturbed.

The video source uses scrambled or

encoded signals to prevent dubbing.

This in not malfunction.

—

This unit suddenly

enters the standby

mode.

The internal temperature is too high and

the overheat protection circuitry has been

activated.

Wait about 1 hour for this unit to cool down and then

turn it back on.

The video conversion

function does not

work.

Some digital signals are input via HDMI

jack.

Turn off the power of the component connected to

HDMI IN jacks.

86 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

■ Tuner

See

page

Problem

Cause

Remedy

FM stereo reception is

noisy.

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

Check the antenna connections.

—

Try using a high-quality directional FM

antenna.

Use the manual tuning method.

—

There is distortion, and

clear reception cannot

be obtained even with a

good FM antenna.

There is multi-path interference.

The signal is too weak.

Adjust the antenna position to eliminate

multi-path interference.

The desired station

cannot be tuned into

with the automatic

tuning method.

Use a high-quality directional FM antenna.

Use the manual tuning method.

—

Previously preset

stations can no longer

be tuned into.

This unit has been disconnected for a

long period.

Set preset stations.

—

The desired station

cannot be tuned into

with the automatic

tuning method.

The signal is weak or the antenna

connections are loose.

Tighten the AM loop antenna connections

and orient it for the best reception.

Use the manual tuning method.

—

There are continuous

crackling and hissing

noises.

Noise can result from lightning,

fluorescent lamps, motors, thermostats

and other electrical equipment.

Use an outdoor antenna and a ground wire.

This will help somewhat, but it is difficult to

eliminate all noise.

There are buzzing and

whining noises.

A TV set is being used nearby.

Move this unit away from the TV set.

—

87 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

■

XM Satellite Radio

If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel

display. In this case, read the cause and follow the corresponding remedies.

See

page

Status message

Cause

Remedy

The XM Mini-Tuner is not installed in the Confirm the XM Mini-Tuner is fully seated in the

CHECK XM TUNER

XM Mini-Tuner Dock or the XM Mini-

Tuner Dock is not connected to this unit.

dock and check the XM Mini-Tuner Dock cable is

connected to this unit.

The XM antenna is not connected to the

XM Mini-Tuner Dock or the XM antenna

cable has become damaged.

Check that the XM antenna is securely connected to

the XM Mini-Tuner Dock and check the antenna

cable for damage. Replace the XM antenna if the

cable is damaged.

CHECK ANTENNA

CH UNAUTH

You may be attempting to tune to an XM

channel that is blocked or that you cannot http://www.xmradio.com/ (US residents) and http://

Consult the latest channel guide at

receive with your XM subscription

package.

www.xmradio.ca/ (Canadian residents) for the current

list of channels. For information on receiving this

channel, visit http://www.xmradio.com/ (US

residents) and http://www.xmradio.ca/ (Canadian

residents) or contact XM Satellite Radio at 1-800-

967-2346 (US residents) and 1-877-GET XMSR

(Canadian residents).

The XM Mini-Tuner is not receiving the

XM satellite signal. Something may be

blocking the XM antenna’s view of the

satellites or the antenna is not properly

aimed.

Check for antenna obstructions and reposition the

XM antenna to get better signal reception. Use the

“XM RADIO SET” screen in the video monitor to

check the antenna reception level. See instructions

supplied with the XM Mini-Tuner and Dock for

antenna installation information.

48, 75

NO SIGNAL

The XM Mini-Tuner is acquiring audio or This message should disappear in a few seconds in

program information from the XM

satellite signal. This message can also

good signal conditions. If you see this message often,

reposition the XM antenna to get better signal

occur in weak XM signal conditions. Note reception. Use the “XM RADIO SET” screen in the

that this unit may not respond to some

operations while this message is

displayed.

video monitor to check the antenna reception level.

The XM channel you selected is not

currently broadcasting.

Check back at a later time; in the mean time, select

another channel.

—

OFF AIR

The selected channel is not available. The Consult the latest channel guide at

CH UNAVAILABLE

channel may have been reassigned to a

different channel number. This message

may occur initially with a new XM Mini-

Tuner or a XM Mini-Tuner that has not

received XM’s signal for an extended

period.

http://www.xmradio.com/ (US residents) and http://

www.xmradio.ca/ (Canadian residents) for the current

list of channels. For cases of a new XM Mini-Tuner

or a XM Mini-Tuner that has not received XM’s

signal for an extended period, allow the XM Mini-

Tuner to receive the XM satellite signal for at least 5

minutes and then try to select the channel again.

No artist name or song title is available for No action required.

this selection.

—

- - - -

88 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

■ SIRIUS Satellite Radio

If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel

display. In this case, read the cause and follow the corresponding remedies.

See

page

Status message

Cause

Remedy

The antenna is not connected to the

SiriusConnect tuner properly.

Check the connection of the antenna and

SiriusConnect tuner.

ANTENNA ERROR

The SiriusConnect tuner is not connected

to the SIRIUS jack of this unit correctly.

Check the connection of the SiriusConnect tuner and

this unit.

CHECK SR TUNER

The SiriusConnect tuner is not connected

to the AC wall outlet.

Connect the power cable of the SiriusConnect tuner

to the AC wall outlet.

This unit does not support the connected

SIRIUS Satellite Radio tuner.

Connect the SiriusConnect tuner that this unit

supports,

NOT SUPPORTED

ACQUIRING

The signal is too weak.

Adjust the orientation of the antenna of the

SiriusConnect tuner. Use the “ANTENNA INFO”

information in the front panel display or “SIRIUS

Information” screen in the video monitor to check the

antenna reception level.

53, 58

The SiriusConnect tuner is updating the

channel list.

Wait until the updating is complete.

—

UPDATING

The period of the subscription is end.

Contact SIRIUS Satellite Radio to renew the

subscription.

The SiriusConnect tuner is updating the

firmware.

Wait until the updating is complete.

F/W UPDATING

The selected channel is not subscribed.

Contact SIRIUS Satellite Radio to subscribe the

selected channel.

URL: https://activate.siriusradio.com/

Phone: 1-888-539-SIRIUS (1-888-539-7474)

CALL SIRIUS

(CALL 888-539-

SIRIUS TO

SUBSCRIBE)

Select another channel.

The subscription information is updated.

SUB UPDATED

INVALID

The selected channel is currently out of

service.

Select another channel.

The operation you made is not available.

Not Available

89 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

■ AUTO SETUP

Before AUTO SETUP

See

page

Error message

Cause

Remedy

Optimizer microphone is not connected.

Connect the supplied optimizer microphone

to the OPTIMIZER MIC jack on the front

panel.

Connect MIC!

—

Headphones are connected.

Unplug the headphones.

Unplug HP!

During AUTO SETUP

Error message

See

page

Cause

Remedy

Front L/R channel signals are not detected.

A surround channel signal is not detected.

Check the front L/R speaker connections.

Check the surround speaker connections.

E-1:NO FRONT SP

E-2:NO SUR.SP

E-3:SBR->SBL

Only a right surround back channel signal is Connect the surround back speaker to the

detected.

LEFT SURROUND BACK SPEAKERS

terminal if you only have one surround

back speaker.

Background noise is too loud.

Try running “AUTO SETUP” in a quiet

environment.

—

E-4:NOISY

Turn off noisy electric equipment like air

conditioners or move them away from the

optimizer microphone.

Surround back speakers are connected,

though surround L/R speakers are not.

Connect surround speakers when you use

surround back speakers.

E-5:CHECK SUR.

E-6:NO MIC

The optimizer microphone was unplugged

during the “AUTO SETUP” procedure.

Connect the supplied optimizer microphone

to OPTIMIZER MIC jack on the front

panel.

The optimizer microphone does not detect

test tones.

Check the microphone setting.

E-7:NO SIGNAL

Check the speaker connections and

placement.

10, 11,

The “AUTO SETUP” procedure was

cancelled due to user activity.

Run “AUTO SETUP” again.

E-8:USER CANCEL

An internal error occurred.

E-9:INTERNAL ERROR

90 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

After AUTO SETUP

See

page

Warning message

Cause

Remedy

Speaker polarity is not correct. This

message may appear depending on the

speakers even when the speakers are

connected correctly.

Check the speaker connections for proper

polarity (+ or –).

W-1:OUT OF PHASE

The distance between the nearest speaker

and the furthest speaker is out of adjustable position.

range.

Bring the speaker closer to the listening

—

26, 67

—

W-2:OVER 24m (80ft)

W-3:LEVEL ERROR

The difference of volume level among

speakers is excessive. (No level correction

is made.)

If “SWFR:TOO LOUD” or “SWFR:TOO

LOW” appears, adjust the output volume of

the subwoofer.

Readjust the speaker installation so that all

speakers are set in locations with similar

conditions.

Check the speaker connections.

Use speakers of similar quality.

—

Notes

• If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.

• If a warning message “W-1”, “W-2”, or “W-3” appears, corrections are made, but they may not be optimal.

• If an error message “E-9” occurs repeatedly, please contact a qualified Yamaha service center.

■ iPod

Note

In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod

(see page 20).

See

page

Status message

Cause

Remedy

This unit is in the middle of recognizing

the connection with your iPod.

This unit is in the middle of acquiring

song lists from your iPod.

There is a problem with the signal path

from your iPod to this unit.

Turn off this unit and reconnect the Yamaha iPod

universal dock to the DOCK terminal of this unit.

Connect error

Try resetting your iPod.

—

The iPod being used is not supported by

this unit.

Only iPod (Click and Wheel), iPod nano, and iPod

mini are supported.

Unknown iPod

Your iPod is properly stationed in a

Yamaha iPod universal dock (YDS-10,

sold separately) connected to the DOCK

terminal of this unit, and the connection

between your iPod and this unit is

complete.

iPod connected

Your iPod was removed from a Yamaha

iPod universal dock (YDS-10, sold

separately) connected to the DOCK

terminal of this unit.

Station your iPod back in a Yamaha iPod universal

dock (YDS-10, sold separately) connected to the

DOCK terminal of this unit.

Disconnected

This unit cannot play back the songs

currently stored on your iPod.

Check that the songs currently stored on your iPod

are playable.

—

Unable to play

Store some other playable music files on your iPod.

91 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

■ Bluetooth

See

page

Status message

Cause

Remedy

The Bluetooth adapter and the Bluetooth

component is in the middle of the pairing.

Searching...

The Bluetooth adapter and the Bluetooth

component is in the middle of establishing

the connection.

The paring is completed.

The paring is canceled.

Completed

Canceled

The connection between the Yamaha

Bluetooth adapter (such as YBA-10, sold

separately) and the Bluetooth component

is established.

BT connected

The Bluetooth component is disconnected

from the Yamaha Bluetooth adapter (such

as YBA-10, sold separately).

Disconnected

No BT Adapter

The Bluetooth adapter is not connected to Connect the Yamaha Bluetooth adapter (such as

the DOCK terminal. YBA-10, sold separately) to the DOCK terminal.

92 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

■ Remote control

See

page

Problem

Cause

Remedy

The remote control

does not work nor

function properly.

Wrong distance or angle.

The remote control functions within a maximum

range of 6 m (20 ft) and no more than 30 degrees off-

axis from the front panel.

Direct sunlight or lighting (from an

inverter type of fluorescent lamp, etc.) is

striking the remote control sensor of this

unit.

Reposition this unit.

—

The batteries are weak.

Replace all batteries.

The remote control code is not correctly

set.

Set the remote control code correctly using “List of

remote control codes” at the end of this manual.

Try setting another code for the same manufacturer

using “List of remote control codes” at the end of this

manual.

Even if the remote control code is

correctly set, there are some models that

do not respond to the remote control.

■ Resetting the system

Use this feature to reset all the parameters of this unit to

Notes

the initial factory settings.

• This procedure completely resets all the parameters of this unit

including the “SET MENU” parameters. However, the

advanced setup menu parameters will not be initialized.

• The initial factory settings are activated next time you turn on

this unit.

Press SYSTEM OFF on the front panel to

set this unit to the standby mode.

Press and hold TONE CONTROL and

then press MAIN ZONE ON/OFF to turn

To cancel the initialization procedure at any time without making

any changes, press STRAIGHT repeatedly to select

on this unit.

“CANCEL” and then press MAIN ZONE ON/OFF.

The advanced setup menu appears in the front panel

display.

Press PROGRAM l/ hto select “INIT.”.

Press STRAIGHT repeatedly to select

“RESET”.

Select “CANCEL” to cancel the initialization

procedure without making any changes.

Press MAIN ZONE ON/OFF to confirm

your selection and set this unit to the

standby mode.

93 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary

■ Bi-amplification connection

■ Dolby Digital

A bi-amplification connection uses two amplifiers for a

speaker. One amplifier is connected to the woofer section

of a loudspeaker while the other is connected to the

combined mid and tweeter section. With this arrangement

each amplifier operates over a restricted frequency range.

This restricted range presents each amplifier with a much

simpler job and each amplifier is less likely to influence

the sound in some way. The internal crossover of the

speaker consists of a LPF (low pass filter) and a HPF (high

pass filter). As its name implies, the LPF passes

frequencies below a cutoff and rejects frequencies above

the cutoff frequency. Likewise, the HPF passes

Dolby Digital is a digital surround sound system that gives

you completely independent multi-channel audio. With 3

front channels (front L/R and center), and 2 surround

stereo channels, Dolby Digital provides 5 full-range audio

channels. With an additional channel especially for bass

effects, called LFE (Low Frequency Effect), the system

has a total of 5.1-channels (LFE is counted as 0.1

channel). By using 2-channel stereo for the surround

speakers, more accurate moving sound effects and

surround sound environment are possible than with Dolby

Surround. The wide dynamic range from maximum to

minimum volume reproduced by the 5 full-range channels

and the precise sound orientation generated using digital

sound processing provide listeners with unprecedented

excitement and realism. With this unit, any sound

environment from monaural up to a 5.1-channel

configuration can be freely selected for your enjoyment.

frequencies above its cutoff.

■ CINEMA DSP

Since the Dolby Surround and DTS systems were

originally designed for use in movie theaters, their effect

is best felt in a theater having many speakers designed for

acoustic effects. Since home conditions, such as room

size, wall material, number of speakers, and so on, can

differ so widely, it is inevitable that there are differences in

the sound heard. Based on a wealth of actually measured

data, Yamaha CINEMA DSP uses Yamaha original sound

field technology to combine Dolby Pro Logic, Dolby

Digital and DTS systems to provide the audiovisual

experience of a movie theater in the listening room of your

own home.

■ Dolby Digital EX

Dolby Digital EX creates 6 full-bandwidth output

channels from 5.1-channel sources. This is done using a

matrix decoder that derives 3 surround channels from the

2 in the original recording. For the best results, Dolby

Digital EX should be used with movie sound tracks

recorded with Dolby Digital Surround EX. With this

additional channel, you can experience more dynamic and

realistic moving sound especially with scenes with

“fly-over” and “fly-around” effects.

■ Component video signal

■ Dolby Pro Logic II

With the component video signal system, the video signal

is separated into the Y signal for the luminance and the P^B

and PR signals for the chrominance. Color can be

reproduced more faithfully with this system because each

of these signals is independent. The component signal is

also called the “color difference signal” because the

luminance signal is subtracted from the color signal. A

monitor with component input jacks is required in order to

output component signals.

Dolby Pro Logic II is an improved technique used to

decode vast numbers of existing Dolby Surround sources.

This new technology enables a discrete 5-channel

playback with 2 front left and right channels, 1 center

channel, and 2 surround left and right channels instead of

only 1 surround channel for conventional Pro Logic

technology. There are three modes available: “Music

mode” for music sources, “Movie mode” for movie

sources and “Game mode” for game sources.

■ Composite video signal

■ Dolby Pro Logic IIx

With the composite video signal system, the video signal

is composed of three basic elements of a video picture:

color, brightness and synchronization data. A composite

video jack on a video component transmits these three

elements combined.

Dolby Pro Logic IIx is a new technology enabling discrete

multi-channel playback from 2-channel or multi-channel

sources. There are three modes available: “Music mode”

for music sources, “Movie mode” for movie sources (for

2-channel sources only) and “Game mode” for game

sources.

94 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary

■ Dolby Surround

■ LFE 0.1 channel

Dolby Surround uses a 4-channel analog recording system

to reproduce realistic and dynamic sound effects: 2 front

left and right channels (stereo), a center channel for dialog

(monaural), and a surround channel for special sound

effects (monaural). The surround channel reproduces

sound within a narrow frequency range. Dolby Surround is

widely used with nearly all video tapes and laser discs,

and in many TV and cable broadcasts as well. The Dolby

Pro Logic decoder built into this unit employs a digital

signal processing system that automatically stabilizes the

volume on each channel to enhance moving sound effects

and directionality.

This channel reproduces low-frequency signals. The

frequency range of this channel is from 20 Hz to 120 Hz.

This channel is counted as 0.1 because it only enforces a

low-frequency range compared to the full-range

reproduced by the other 5/6 channels in Dolby Digital or

DTS 5.1/6.1-channel systems.

■ Neo:6

Neo:6 decodes the conventional 2-channel sources for 6-

channel playback by the specific decoder. It enables

playback with the full-range channels with higher

separation just like digital discrete signal playback. There

are two modes available: “Music mode” for music sources

and “Cinema mode” for movie sources.

■ DTS 96/24

DTS 96/24 offers an unprecedented level of audio quality

for multi-channel sound on DVD video, and is fully

backward-compatible with all DTS decoders. “96” refers

to a 96 kHz sampling rate compared to the typical 48 kHz

sampling rate. “24” refers to 24-bit word length. DTS 96/

24 offers sound quality transparent to the original 96/24

master, and 96/24 5.1-channel sound with full-quality full-

motion video for music programs and motion picture

soundtracks on DVD video.

■ Neural Surround

™

Neural Surround represents the latest advancement in

surround technology and has been adopted by XM

Satellite Radio for digital radio broadcast of surround

recordings and live events in surround sound. Neural

™

Surround employs psychoacoustic frequency domain

processing which allows delivery of a more detailed sound

stage with superior channel separation and localization of

audio elements. System playback is scalable from 5.1 to

7.1 multi-channel surround playback.

■ DTS Digital Surround

DTS digital surround was developed to replace the analog

soundtracks of movies with a 6.1-channel digital sound

track, and is now rapidly gaining popularity in movie

theaters around the world. DTS, Inc. has developed a

home theater system so that you can enjoy the depth of

sound and natural spatial representation of DTS digital

surround in your home. This system produces practically

distortion-free 6.1-channel sound (technically, front left

and right, center, surround left and right, and LFE 0.1

(subwoofer) channels for a total of 5.1 channels). This unit

incorporates a DTS-ES decoder that enables 6.1-channel

reproduction by adding the surround back channel to the

existing 5.1-channel format.

■ PCM (Linear PCM)

Linear PCM is a signal format under which an analog

audio signal is digitized, recorded and transmitted without

using any compression. This is used as a method of

recording CDs and DVD audio. The PCM system uses a

technique for sampling the size of the analog signal per

very small unit of time. Standing for “Pulse Code

Modulation”, the analog signal is encoded as pulses and

then modulated for recording.

■ Sampling frequency and number of

quantized bits

When digitizing an analog audio signal, the number of

times the signal is sampled per second is called the

sampling frequency, while the degree of fineness when

converting the sound level into a numeric value is called

the number of quantized bits. The range of rates that can

be played back is determined based on the sampling rate,

while the dynamic range representing the sound level

difference is determined by the number of quantized bits.

In principle, the higher the sampling frequency, the wider

the range of frequencies that can be played back, and the

higher the number of quantized bits, the more finely the

sound level can be reproduced.

■ HDMI

HDMI (High-Definition Multimedia Interface) is the first

industry-supported, uncompressed, all-digital audio/video

interface. Providing an interface between any source (such

as a set-top box or AV receiver) and an audio/video

monitor (such as a digital television), HDMI supports

standard, enhanced or high-definition video as well as

multi-channel digital audio using a single cable. HDMI

transmits all ATSC HDTV standards and supports 8-

channel digital audio, with bandwidth to spare to

accommodate future enhancements and requirements.

When used in combination with HDCP (High-bandwidth

Digital Content Protection), HDMI provides a secure

audio/video interface that meets the security requirements

of content providers and system operators. For further

information on HDMI, visit the HDMI website at

“http://www.hdmi.org/”.

95 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary

■ SILENT CINEMA

Yamaha has developed a natural, realistic sound effect

DSP algorithm for headphones. Parameters for

headphones have been set for each sound field so that

accurate representations of all the sound field programs

can be enjoyed on headphones.

■ S-video signal

With the S-video signal system, the video signal normally

transmitted using a pin cable is separated and transmitted

as the Y signal for the luminance and the C signal for the

chrominance through the S-video cable. Using the S

VIDEO jack eliminates video signal transmission loss and

allows recording and playback of even more beautiful

images.

■ Virtual CINEMA DSP

Yamaha has developed a Virtual CINEMA DSP algorithm

that allows you to enjoy DSP sound field surround effects

even without any surround speakers by using virtual

surround speakers. It is even possible to enjoy Virtual

CINEMA DSP using a minimal two-speaker system that

does not include a center speaker.

96 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

• Signal Level

AUDIO SECTION

Composite ................................................................. 1 Vp-p/75 Ω

S-video ............................ 1 Vp-p/75 Ω (Y), 0.286 Vp-p/75 Ω (C)

Component ................... 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (P^B/PR)

• Minimum RMS Output Power for Front, Center, Surround,

Surround Back

[U.S.A. and Canada models]

1 kHz, 0.9% THD, 8 Ω ...................................................... 90 W

[Other models]

1 kHz, 0.9% THD, 6 Ω ...................................................... 90 W

• Signal to Noise Ratio ................................................ 50 dB or more

• Maximum Input Level........................................... 1.5 Vp-p or more

• Frequency Response (MONITOR OUT)

• Maximum Power for Front, Center, Surround, Surround Back

(JEITA)

Component Signal .................................... 5 Hz to 60 MHz, –3 dB

[U.S.A. and Canada models]

1 kHz, 10% THD, 8 Ω ..................................................... 115 W

[Other models]

FM SECTION

• Tuning Range

[U.S.A. and Canada models] ........................... 87.5 to 107.9 MHz

[Asia and General models] ........ 87.5/87.50 to 108.0/108.00 MHz

[Other models] ............................................ 87.50 to 108.00 MHz

1 kHz, 10% THD, 6 Ω ..................................................... 115 W

• Dynamic Power

[U.S.A. and Canada models]

(IHF, 8/6/4/2 Ω) ............................................ 90/110/130/150 W

[Other models]

• 50 dB Quieting Sensitivity (IHF, 100% mod.)

Mono ................................................................. 2.8 µV (20.2 dBf)

(IHF, 6/4/2 Ω) .................................................... 100/110/125 W

• Signal to Noise Ratio (IHF)

Mono/Stereo .............................................................. 73 dB/70 dB

• Dynamic Headroom [U.S.A. and Canada models]

8 Ω .................................................................................... 0.18 dB

• Harmonic Distortion (1 kHz)

Mono/Stereo ................................................................ 0.5%/0.5%

• Maximum Input Signal

CD, etc. Effect On, 1 kHz, 0.5% THD ................... 2.0 V or more

• Antenna Input (unbalanced) ..................................................... 75 Ω

• Frequency Response

AM SECTION

• Tuning Range

CD, etc. to Front L/R ............................. 10 Hz to 100 kHz, –3 dB

• Total Harmonic Distortion

[U.S.A. and Canada models] .............................. 530 to 1710 kHz

[Asia and General models] ................. 530/531 to 1710/1611 kHz

[Other models] ................................................... 531 to 1611 kHz

[U.S.A. and Canada models]

(1 kHz, 50 W, Front L/R, 8 Ω ) ............................. 0.06% or less

[Other models]

(1 kHz, 50 W, Front L/R, 6 Ω ) ............................. 0.06% or less

GENERAL

• Signal to Noise Ratio (IHF-A Network)

• Power Supply

CD (200 mV) to Front L/R, Effect Off ................... 98 dB or more

CD (250 mV) to Front L/R, Effect Off ................. 100 dB or more

[U.S.A. and Canada models] ............................. 120 V AC, 60 Hz

[Australia model] .............................................. 240 V AC, 50 Hz

[Korea model] ................................................... 220 V AC, 60 Hz

[China model] .................................................... 220 V AC, 50 Hz

[Asia and General models]

• Residual Noise (IHF-A Network)

Front L/R ............................................................... 150 µV or less

• Channel Separation (1 kHz/10 kHz)

.............................................. 110-120/220-240 V AC, 50/60 Hz

CD, etc. (5.1 kΩ shorted) to Front L/R

................................................................... 60 dB/45 dB or more

• Power Consumption

[U.S.A. and Canada models] ................................. 240 W/320 VA

[General model] ................................................................. 260 W

[Other models] ................................................................... 240 W

• Tone Control (Front L/R)

BASS Boost/Cut ................................................... 10 dB/100 Hz

TREBLE Boost/Cut .............................................. 10 dB/20 kHz

• Standby Power Consumption ...................................... 0.8 W or less

• Headphone Jack Rated Output/Impedance .............. 400 mV/470 Ω

• Maximum Power Consumption [Asia and General models only]

5ch, 10% THD ................................................................... 490 W

• Input Sensitivity/Input Impedance

CD, etc. ................................................................. 200 mV/47 kΩ

MULTI CH INPUT ............................................... 200 mV/47 kΩ

• AC Outlets

[Australia model] ....................................... 1 (100 W maximum)

[U.S.A., Canada and China models] ...2 (Total 100 W maximum)

[Other model]........................................2 (Total 50 W maximum)

• Output Level/Output Impedance

AUDIO OUT (REC) ............................................ 200 mV/1.2 kΩ

SUBWOOFER OUTPUT ............................................ 4 V/1.2 kΩ

• Dimensions (W x H x D) ................................. 435 x 151 x 352 mm

(17-1/8” x 5-15/16” x 13-7/8”)

• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)

H.P.F.

• Weight ............................................................. 9.0 kg (19 lbs 13 oz)

(FRONT SP, CENTER SP, SUR. L/R SP, SUR. B L/R SP:

SMALL/SML) ............................................................12 dB/oct.

L.P.F. (Subwoofer) .........................................................24 dB/oct.

* Specifications are subject to change without notice.

VIDEO SECTION

• Video Signal Type (Gray back)

[U.S.A., Canada, Korea and General models] .................... NTSC

[Other models] ....................................................................... PAL

• Video Signal Type (Video Conversion) ......................... NTSC/PAL

97 En

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX

Index

Bluetooth setting, Option menu ...........75

BT connected,

Bluetooth status message .................92

Controlling other components,

Remote control ................................ 77

Controlling this unit,

■

Symbols

<XM> - - -,

XM tuning status message ............... 88

Remote control ................................ 76

Creating original SCENE

■

Numerics

C)AUDIO SELECT, Option menu ......74

C)SP DISTANCE, Sound menu ..........68

C)VOLUME TRIM, Input menu .........72

CALL SIRIUS, SIRIUS Satellite Radio

status message ..................................89

Canceled, Troubleshooting ..................92

CAT SEARCH, XM tuning .................55

Category Search mode, XM tuning ......50

CD player, Connection .........................19

CD recorder, Connection .....................19

CENTER SP, Speaker settings .............65

Center speaker equalizer,

Sound menu .....................................68

Center speaker, Speaker settings ..........65

Center width, Sound field parameter ...42

CHECK ANTENNA, XM tuning status

message ............................................88

CHECK SR TUNER, SIRIUS Satellite

Radio status message .......................89

CINEMA DSP indicator ......................25

COAXIAL IN (1),

Input assignment ..............................71

COAXIAL INPUT assignment,

Input assignment ..............................71

COAXIAL INPUT jacks ......................71

Completed,

Bluetooth status message .................92

COMPONENT VIDEO jacks ..............13

Connect error, iPod controlling status

message ............................................91

Connect MIC!,

templates ......................................... 33

CROSSOVER, Speaker settings ......... 67

Crossover, Speaker settings ................. 67

CT WIDTH,

Sound field parameter ..................... 42

Current status display .......................... 37

1 SOUND MENU, Manual setup ........ 63

2 INPUT MENU, Manual setup .......... 63

2ch Stereo, Sound field program ......... 40

3 OPTION MENU ............................... 73

3 OPTION MENU, Manual setup ....... 64

7ch Stereo, Sound field program ......... 40

96/24 indicator ..................................... 24

■

D)CENTER GEQ, Sound menu .......... 68

D)DECODER MODE, Input menu ..... 72

D)PARAM. INI, Option menu ............ 74

Decoder indicators ............................... 24

Decoder mode, Input menu ................. 72

Decoder select mode,

Decoder mode ................................. 72

DIGITAL AUDIO COAXIAL jacks ... 13

DIGITAL AUDIO OPTICAL jacks .... 13

DIMENSION,

A)DISPLAY SET, Option menu ......... 73

A)INPUT ASSIGNMENT,

Input menu ....................................... 71

A)SPEAKER SET, Sound menu ......... 65

A.DELAY, Audio settings ................... 69

AC OUTLET(S) (SWITCHED) .......... 22

ACQUIRING, SIRIUS Satellite Radio

status message ................................. 89

Activating XM Satellite Radio ............ 49

ALL CH SEARCH, XM tuning ........... 55

All Channel Search mode,

XM tuning ................................. 50, 55

AM antenna connection ....................... 21

AM tuning ............................................ 45

Amplifier function OSD display time,

Display settings ............................... 73

ANTENNA ERROR, SIRIUS Satellite

Radio status message ....................... 89

Audio components, Connection ........... 19

Audio delay, Audio settings ................. 69

Audio information ................................ 38

Audio input jacks selection .................. 36

AUDIO jacks ....................................... 13

Audio jacks .......................................... 13

AUDIO SELECT ................................. 36

Audio select, Option menu .................. 74

Audio settings, Sound menu ................ 69

Audio signal flow ................................. 15

AUTO SETUP ..................................... 26

AUTO SETUP, Error message ............ 90

Automatic preset tuning,

Sound field parameter ..................... 42

Dimension,

Sound field parameter ..................... 42

DIMMER, Display settings ................. 73

Dimmer, Display settings .................... 73

DIRECT ............................................... 43

Direct Number Access mode,

XM tuning ....................................... 50

Direct number access mode,

XM tuning ....................................... 55

Disconnected,

Bluetooth status message ................ 92

Disconnected,

iPod controlling status message ...... 91

Display settings,

Option menu .................................... 73

Displaying the XM Satellite Radio

information ...................................... 52

DIST .................................................... 28

DIST, Auto setup result ....................... 28

DISTANCE ......................................... 27

DISTANCE, Auto setup ...................... 27

DOCK indicator .................................. 24

DSP LEVEL,

Auto setup error message .................90

Connecting to the FRONT A

terminals ...........................................12

Connection,

AM antenna connection ...................21

Connection, Audio components ...........19

Connection, CD player .........................19

Connection, CD recorder .....................19

Connection, DVD player ......................17

Connection, DVD recorder ..................18

Connection, external decoder ...............19

Connection, FM antenna ......................21

Connection, HDMI ...............................14

Connection, MD recorder ....................19

Connection, Multi-format player .........19

Connection, Power cable ......................22

Connection, PVR .................................18

Connection, set-top boxes ....................18

Connection, VCR .................................18

Connection, Video components ...........16

Connection,

FM/AM tuning ................................. 46

Automatic tuning, FM/AM tuning ....... 45

Sound field parameter ..................... 42

DSP level,

Sound field parameter ..................... 42

DTS decoder prioritize setting,

Decoder mode ................................. 72

DVD player connection ....................... 17

DVD recorder connection ................... 18

Dynamic range, Sound menu .............. 69

■

B)INPUT RENAME,

Input menu ....................................... 71

B)MEMORY GUARD,

Option menu .................................... 74

B)SPEAKER LEVEL,

Sound menu ..................................... 67

Background Video,

Multi channel input setup ................ 72

BGV, Multi channel input setup .......... 72

BI-AMP, Advanced setup .................... 82

Bi-Amplifier, Advanced setup ............. 82

■

E)EXTD SUR., Sound menu ............... 70

E)LFE LEVEL, Sound menu .............. 68

E)MULTI CH SET, Input menu .......... 72

Yamaha iPod universal dock ...........20

Controlling a TV ..................................76

98 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

E)XM RADIO SET,

Option menu ....................................75

E-1:NO FRONT SP,

Auto setup error message ................90

E-2:NO SURR.SP,

Auto setup error message ................90

E-3:SBR->SBL,

Auto setup error message ................90

E-4:NOISY,

Auto setup error message ................90

E-5:CHECK SUR.,

Auto setup error message ................90

E-6:NO MIC,

Auto setup error message ................90

E-7:NO SIGNAL,

Auto setup error message ................90

E-8:USER CANCEL,

Auto setup error message ................90

E-9:INTERNAL ERROR,

Auto setup error message ................90

Effect level, Sound field parameter .....42

ENHANCER indicator ........................24

Exchange, Preset station,

FM/AM tuning .................................47

Extended surround, Sound menu .........70

External decoder connection ................19

HEADPHONE,

Low-frequency effect level ..............68

Headphone,

Low-frequency effect level ..............68

Headphones ..........................................37

Headphones indicator ...........................24

MULTI CH INPUT jacks .................... 19

Multi channel input setup,

Input menu ....................................... 72

Multi-channel source

with headphones .............................. 41

Multi-format player connection ........... 19

Multi-information display ................... 25

MULTI-ZONE Configuration ............. 79

Music Enh. 2ch,

■

I) EXTD SUR., Sound menu ................70

Infrared window, Remote control ........25

INI.VOL., Audio settings .....................69

Initial volume, Audio settings ..............69

Input assignment, Input menu ..............71

INPUT CH,

Multi-channel input setup ................72

Input channel and

speaker indicators .............................25

Input channel indicators .......................25

Input channels,

Multi-channel input setup ................72

Input menu, Manual setup ....................63

Input rename, Input menu ....................71

Input source indicators .........................24

Input source information display .........38

INVALID, SIRIUS Satellite Radio status

message ............................................89

iPod connected, iPod controlling status

message ............................................91

iPod control, Status message ................91

iPod using .............................................59

Sound field program ........................ 40

Music Enh. 7ch,

Sound field program ........................ 40

MUTE .................................................. 37

MUTE indicator ................................... 24

MUTE TYPE, Audio settings .............. 69

Muting ................................................. 37

■

Neo:6 Music ........................................ 41

Neural Surround .................................. 41

Night listening mode ........................... 44

No BT Adapter,

Bluetooth status message ................ 92

NO SIGNAL,

XM tuning status message ............... 88

Not Available, SIRIUS Satellite Radio

status message ................................. 89

NOT SUPPORTED, SIRIUS Satellite

Radio status message ....................... 89

Number of speakers ............................. 28

Number of speakers,

■

F)DYNAMIC RANGE,

Sound menu .....................................69

F/W UPDATING, SIRIUS Satellite Radio

status message ..................................89

Factory presets,

Advanced setup ................................83

FL SCROLL, Display settings .............73

FM antenna ..........................................21

FM antenna connection ........................21

FM tuning ............................................45

FRONT B speaker setting,

Speaker settings ...............................65

FRONT B, Speaker settings .................65

Front input,

Multi-channel input setup ................72

Front panel display ...............................24

Front panel display scroll,

■

Auto setup result .............................. 28

Jazz, Sound field program ....................40

■

OFF AIR,

XM tuning status message ............... 88

OPTICAL IN (2),

Input assignment ............................. 71

OPTICAL IN (3),

Input assignment ............................. 71

OPTICAL INPUT assignment,

Input assignment ............................. 71

OPTIMIZER MIC jack,

Auto setup ....................................... 26

Optimizer microphone ......................... 26

Optimizer microphone,

Auto setup ....................................... 26

Optimizing speaker setting .................. 26

Option menu, Manual setup ................ 64

OSD SHIFT, Display settings ............. 73

OSD shift, Display settings ................. 73

OSD-AMP, Display settings ............... 73

OSD-SOURCE, Display settings ........ 73

Other components controlling

LFE/BASS OUT, Speaker settings ......66

LFE/Bass out, Speaker settings ............66

LOADING,

XM tuning status message ...............88

Loading...,

iPod controlling status message .......91

Low-frequency effect level,

Sound menu .....................................68

LVL ......................................................28

LVL, Auto setup result .........................28

Display settings ................................73

FRONT SP, Speaker settings ...............65

Front speakers, Speaker settings ..........65

FRONT,

■

Manual preset tuning,

FM/AM tuning .................................46

MANUAL SETUP, SET MENU .........63

Manual setup, SET MENU ..................63

Manual tuning, FM/AM tuning ............45

MAX VOL., Audio settings .................69

Maximum volume, Audio settings .......69

MD recorder, Connection .....................19

Memory guard, Option menu ...............74

Menu browse mode,

Multi-channel input setup ................72

■

G)AUDIO SET, Sound menu ..............69

G)SIRIUS SET ....................................75

Games, Sound field program ...............40

by remote control ............................ 77

Other components controlling,

Remote control ................................ 77

■

iPod controlling ................................60

Movie Dramatic,

Sound field program ........................40

Movie Spacious,

Sound field program ........................40

MULTI CH INPUT component

selection ...........................................36

H) HDMI SET, Sound menu ...............70

Hall, Sound field program ...................40

HDMI indicator ....................................24

HDMI set, Sound menu .......................70

HDMI, Connection ..............................14

HEADPHONE, Dynamic range ..........69

Headphone, Dynamic range .................69

■

PANORAMA,

Sound field parameter ..................... 42

Panorama,

Sound field parameter ..................... 42

99 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

Parameter initialization,

SILENT CINEMA ...............................41

SILENT CINEMA indicator ................25

Simple remote mode,

iPod controlling ................................59

SIRIUS Satellite Radio ........................89

SIRIUS Satellite Radio

parental lock .....................................75

SIRIUS Satellite Radio Parental Lock,

Advanced setup ................................82

SIRIUS Satellite Radio setting .............75

SIRIUS Satellite Radio tuning .............53

SiriusConnect tuner ..............................53

SIZE .....................................................27

SIZE, Auto setup ..................................27

SLEEP indicator ...................................25

Sleep timer ...........................................39

Sound field programs

SUR. L/R SP, Speaker settings ........... 66

Surround back left/right speakers,

Speaker settings ............................... 66

Surround left/right speakers,

Option menu .................................... 74

PARENTAL LOCK, SIRIUS Satellite

Radio setting .................................... 75

PCM indicator ...................................... 24

PHONES jack ...................................... 37

Play information display,

Speaker settings ............................... 66

■

Test tone,

Center speaker equalizer ................. 68

iPod controlling ............................... 60

Playing video sources

TEST, Center speaker equalizer .......... 68

Tonal quality adjustment ..................... 43

Troubleshooting ................................... 84

TU, Advanced setup ............................ 83

Tuner (FM/AM),

in the background ............................ 38

PLII Game ............................................ 41

PLII Movie ........................................... 41

PLII Music ........................................... 41

PLIIx Game .......................................... 41

PLIIx Movie ......................................... 41

PLIIx Music ......................................... 41

Pop/Rock, Sound field program ........... 40

Power cable, Connection ..................... 22

Preset channel setting,

XM tuning ................................. 51, 56

Preset SCENE templates ...................... 32

Preset Search mode,

XM tuning ................................. 50, 55

PRESET SEARCH, XM tuning .......... 55

Preset station exchange,

Troubleshooting .............................. 87

Tuner frequency step,

Advanced setup ............................... 83

Tuner indicators ................................... 24

Turning off the power .......................... 23

Turning on the power .......................... 23

TV Sports, Sound field program ......... 40

with headphones ..............................41

Sound menu, Manual setup ..................63

Source feature OSD display time,

Display settings ................................73

SP .........................................................28

SP A B indicators .................................24

SP IMP., Advanced setup ....................82

SP, Auto setup result ............................28

Speaker distance .............................27, 28

Speaker distance, Auto setup ...............27

Speaker distance,

Auto setup result ..............................28

Speaker distance, Sound menu .............68

Speaker distances,

Speaker distance ..............................68

Speaker impedance setting ...................23

Speaker impedance,

Advanced setup ................................82

Speaker level ........................................28

Speaker level adjustment .....................43

Speaker level, Auto setup result ...........28

Speaker level, Sound menu ..................67

Speaker settings, Sound menu .............65

Speaker size ..........................................27

Speaker size, Auto setup ......................27

Speaker wiring .....................................27

Speaker wiring, Auto setup ..................27

Speaker wiring/volume level,

Auto setup ........................................27

SPEAKER, Dynamic range .................69

Speaker, Dynamic range ......................69

SPEAKER,

Low-frequency effect level ..............68

Speaker,

Low-frequency effect level ..............68

Specifications .......................................97

SR PIN, Advanced setup ......................82

Standby mode, Zone 2 .........................81

STRAIGHT ..........................................41

Straight .................................................41

SUB UPDATED, SIRIUS Satellite Radio

status message ..................................89

SUBWOOFER PHASE,

Speaker settings ...............................67

Subwoofer phase, Speaker settings ......67

SUPPORT AUDIO, HDMI set ............70

Support audio, HDMI set .....................70

■

Unable to play, iPod controlling status

message ........................................... 91

UNIT, Speaker distance ...................... 68

Unit, Speaker distance ......................... 68

Unknown iPod, iPod controlling status

message ........................................... 91

Unplug HP!,

Auto setup error message ................ 90

UPDATING, SIRIUS Satellite Radio

status message ................................. 89

UPDATING,

FM/AM tuning ................................. 47

Preset station selection,

FM/AM tuning ................................. 47

PRESET, Advanced setup ................... 83

Pro Logic .............................................. 41

Pure hi-fi sound .................................... 43

PVR connection ................................... 18

■

XM tuning status message .............. 88

Remote control codes ............................iii

Remote control, Troubleshooting ........ 93

REMOTE IN/OUT jacks ..................... 20

Rename, SCENE template ................... 33

Repeat .................................................. 60

Repeat, iPod controlling ...................... 60

Resetting the system ............................ 93

■

VCR connection .................................. 18

VIDEO AUX jacks, Front panel ......... 21

Video components, Connection .......... 16

VIDEO CONV., Display settings ........ 73

Video conversion,

Display settings ............................... 73

Video information ............................... 38

VIDEO jacks ....................................... 13

Video jacks .......................................... 13

Video signal flow ................................ 15

Video sources in the background ........ 38

Virtual CINEMA DSP ......................... 41

VIRTUAL indicator ............................ 25

VOLTAGE SELECTOR ....................... 3

VOLUME level indicator .................... 24

Volume Trim, Input menu ................... 72

■

S VIDEO jacks ..................................... 13

SB L/R SP, Speaker settings ................ 66

SCENE ................................................... 7

SCENE IR code setting,

Advanced setup ............................... 83

SCENE IR, Advanced setup ................ 83

SCENE template selection ................... 30

Searching...,

Bluetooth status message ................. 92

Selection, Audio input jacks ................ 36

Selection,

MULTI CH INPUT component ...... 36

Selection, Preset station,

FM/AM tuning ................................. 47

Selection, SCENE template ................. 30

SET MENU .......................................... 63

Setting remote control codes ................ 78

Setting SCENE template input source,

Remote control ................................ 34

Set-top box connection ........................ 18

Shuffle, iPod controlling ...................... 60

■

W-1:OUT OF PHASE,

Auto setup error message ................ 91

W-2:DISTANCE ERROR,

Auto setup error message ................ 91

W-3:LEVEL ERROR,

Auto setup error message ................ 91

WIRING/LEVEL ................................ 27

WIRING/LEVEL, Auto setup ............. 27

100 En

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

■

XM ANTENNA,

XM Radio setting .............................75

XM Mini-Tuner Dock ..........................48

XM Radio antenna,

XM Radio setting .............................75

XM Radio setting,

Option menu ....................................75

XM Satellite Radio tuning ...................48

XM Satellite Radio,

Status message .................................88

■

Yamaha iPod universal dock,

Connection .......................................20

Yamaha Parametric Room Acoustic

Optimizer .........................................26

YPAO ...................................................26

YPAO (Yamaha Parametric Room

Acoustic Optimizer) ........................26

YPAO indicator ...................................24

■

Zone 2 ..................................................79

ZONE2 indicator ..................................24

101 En

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Front panel/Face avant

BCD

IJ K

VOLUME

MAIN ZONE

ON/OFF

OPTIMIZER MIC

SYSTEM OFF

EDIT

SEARCH MODE

PRESET/TUNING

ZONE

ON/OFF