MIXING CONSOLE
Owner’s Manual
MG16/4
MG12/4
Making the Most Of Your Mixer
Pages 6 to 17
E
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
—For correct operation —
Connector pin assignments
Influence on cell phone usage
G XLR-type connectors are wired as follows: pin 1: ground, pin 2:
G Using a cell phone (mobile telephone) near this unit may induce
hot (+), and pin 3: cold (–).
noise. If noise occurs, use the telephone away from the unit.
G Insert TRS phone jacks are wired as follows: sleeve: ground, tip:
send, and ring: return.
Replacing abrasive parts
G The performance of components with moving contacts, such
switches, rotary controls, faders, and connectors, deteriorates
over time. The rate of deterioration depends on the operating
environment and is unavoidable. Consult your dealer about
replacing defective components.
G Always turn the power off when the mixer is not in use.
G Even when the power switch is in the “STANDBY” position, electricity is still flowing to the mixer at the minimum level. When you are
not using the mixer for a long time, make sure you unplug the AC power adaptor from the wall AC outlet.
Copying of the commercially available music data and/or digital audio files is strictly prohibited except for your personal use.
Illustration examples shown herein are for explanatory purposes only, and may not match actual appearance during operation.
The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective companies.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:
BLUE
: NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying the terminals in your
plug proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (2 wires)
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Introduction
Thank you for your purchase of the YAMAHA MG16/4 or MG12/4 mixing console. This mixing
console combines ease of operation with support for multiple usage environments, and is
ideal for SR setups, installed systems, and many other such applications.
Please read through this Owner’s Manual carefully before beginning use, so that you will be
able to take full advantage of the mixer’s superlative features and enjoy trouble-free operation
for years to come.
Features
Contents
G The MG16/4 provides 16 input channels that can assign to Ste-
reo or Group output.
Introduction ............................................................... 4
Features ............................................................... 4
Contents .............................................................. 4
Before Turning on the Mixer ................................. 5
Turning the Power On .......................................... 5
G The MG12/4 provides 12 input channels that can assign to Ste-
reo or Group output.
G The monitor includes a convenient C-R OUT jack. This jack can
be used to monitor the main Stereo output, the PFL signal, or the
Group 1-2 signals.
G The mixer includes dual AUX SEND jacks and a single
RETURN jack. The two independent AUX buses may be used as
sends to external effectors and monitor systems.
Making the Most Of Your Mixer ................................. 6
1 A Place For Everything and Everything
In Its Place ....................................................... 7
G Phantom power supply enables easy connection to condenser
2 Where Your Signal Goes Once It’s Inside
microphones that run on external power.
the Box .......................................................... 10
G The mixer provides channel-specific INSERT I/O jacks for input
channels 1 to 8 (MG16/4) or 1 to 4 (MG12/4). These jacks make
it possible to insert different effectors into different channels.
3 The First Steps in Achieving Great Sound .... 11
4 External Effects, Monitor Mixes,
G Input channels 1 to 8, 9/10, and 11/12 (MG16/4), and 1 to 4, 5/6,
and 7/8 (MG12/4) are each equipped with both an XLR mic
input jack and a TRS phone-type line jack. Input channels 13/14
and 15/16 (MG16/4), and 9/10 and 11/12 (MG12/4) are each
equipped with both a TRS line input jack and an RCA line input
jack. This wide assortment of connectors enables connection to
many different devices, from microphones to line-level devices
to stereo-output synthesizers.
and Groups .................................................... 13
5 Making Better Mixes....................................... 16
Front & Rear Panels ................................................ 18
Channel Control Section .................................... 18
Master Control Section ...................................... 20
Rear Input/Output Section ................................. 22
Setting Up ............................................................... 24
Setup Procedure ................................................ 24
Setup Examples ................................................ 24
Rack Mounting ................................................... 26
Appendix ................................................................. 27
Specifications .................................................... 27
Dimensional Diagrams ....................................... 29
Block Diagram and Level Diagram .................... 30
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Introduction
Before Turning on the Mixer
Turning the Power On
(1) Be sure that the mixer’s power switch is in the STANDBY
position.
Press the mixer’s power switch to the ON position. When you are
ready to turn the power off, press the power switch to the
STANDBY position.
Use only the PA-20 adaptor included with this mixer.
Use of a different adaptor may result in equipment
damage, overheating, or fire.
Note that trace current continues to flow while the
switch is in the STANDBY position. If you do not plan
to use the mixer again for a long while, please be sure
to unplug the adaptor from the wall outlet.
(2) Connect the power adaptor to the AC ADAPTOR IN con-
nector (1) on the rear of the mixer, and then turn the fas-
tening ring clockwise (2) to secure the connection.
2
1
(3) Plug the power adaptor into a standard household power outlet.
Be sure to unplug the adaptor from the outlet when
not using the mixer, or when there are lightning
storms in the area.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Making the Most OfYour Mixer
An Introduction
You’ve got yourself a mixer and now you’re ready to use it.
Just plug everything in, twiddle the controls, and away you go … right?
Well, if you’ve done this before you won’t have any problems, but if this is
the first time you’ve ever used a mixer you might want to read through this
little tutorial and pick up a few basics that will help you get better
performance and make better mixes.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Making the Most Of Your Mixer
A Place For Everything and Everything In Its Place
1
1-1. A Plethora Of Connectors—What Goes Where?
Questions you’re likely to encounter when setting up a system for the first time might include “Why all
these different types of connectors on the back of my mixer?” and “What’s the difference?”.
Let’s start by taking a look at the most common connector types.
The Venerable RCA Pin Jack
This is the “consumer connector,” and the one that has been most commonly used
on home audio gear for many years. Also known as “phono” jacks (short for
”phonogram”), but the term isn’t used much these days—besides, it’s too easily
confusable with “phone” jacks, below. RCA pin jacks are always unbalanced, and
generally carry a line-level signal at –10 dB, nominal. You’re most likely to use this
type of connector when connecting a CD player or other home audio type source
to your mixer, or when connecting the output of your mixer to a cassette recorder
or similar gear.
White
Red
The Versatile Phone Jack
The name “phone jack” arose simply because this configuration was first
used in telephone switchboards. Phone jacks can be tricky because you
can’t always tell what type of signal they’re designed to handle just by
looking at them. It could be unbalanced mono, unbalanced stereo,
balanced mono, or an insert patch point. The connector’s label will
usually tell you what type of signal it handles, as will the owner’s manual
(you do keep your manuals in a safe place, don’t you?). A phone jack that
is set up to handle balanced signals is also often referred to as a “TRS”
phone jack. “TRS” stands for Tip-Ring-Sleeve, which describes the
configuration of the phone plug used.
Stereo/TRS phone plug
Mono phone plug
The Sturdy XLR
This type of connector is generally referred to as “XLR-type,” and almost always
carries a balanced signal. If the corresponding circuitry is designed properly,
however, XLR-type connectors will also handle unbalanced signals with no
problem. Microphone cables usually have this type of connector, as do the inputs
and outputs of most professional audio gear.
Male
Female
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Making the Most Of Your Mixer
1-2. Balanced, Unbalanced—What’s the Difference?
In a word: “noise.” The whole point of balanced lines is noise rejection, and it’s something they’re very
good at. Any length of wire will act as an antenna to pick up the random electromagnetic radiation we’re
constantly surrounded by: radio and TV signals as well as spurious electromagnetic noise generated by
power lines, motors, electric appliances, computer monitors, and a variety of other sources. The longer
the wire, the more noise it is likely to pick up. That’s why balanced lines are the best choice for long
cable runs. If your “studio” is basically confined to your desktop and all connections are no more than a
meter or two in length, then unbalanced lines are fine—unless you’re surrounded by extremely high lev-
els of electromagnetic noise. Another place balanced lines are almost always used is in microphone
cables. The reason for this is that the output signal from most microphones is very small, so even a tiny
amount of noise will be relatively large, and will be amplified to an alarming degree in the mixer’s high-
gain head amplifier.
To summarize:
Microphones:
Use balanced lines.
Short line-level runs: Unbalanced lines are fine if you’re in a relatively noise-free environment.
Long line-level runs: The ambient electromagnetic noise level will be the ultimate deciding factor, but
balanced is best.
I How Do Balanced Lines Reject Noise?
** Skip this section if technical details make you queasy. **
Balanced lines work on the principle of “phase cancellation”: if you add two identical signals out of
phase (i.e. one signal is inverted so its peaks coincide with the troughs in the other signal), the result is …
nothing. A flat line. The signals cancel each other out.
Normal-phase signal.
No signal.
(Phase cancellation)
Reverse-phase signal.
A balanced cable has three conductors:
1) A ground conductor which carries no signal, just the “ground” or “0” reference against which the
signal in the other conductors fluctuates.
2) A “hot” or “+” conductor which carries the normal-phase audio signal.
3) A “cold” or “–” conductor which carries the reverse-phase audio signal.
While the desired audio signals in the hot and cold conductors are out of phase, any noise induced in
the line will be exactly the same in both conductors, and thus in phase. The trick is that the phase of
one signal is reversed at the receiving end of the line so that the desired audio signals become in-
phase, and the induced noise suddenly finds itself out of phase. The out-of-phase noise signal is effec-
tively canceled while the audio signal is left intact. Clever, eh?
Normal-phase signal
+ normal-phase noise.
Desired signal
with no noise.
Normal-phase signal
+ reverse-phase noise.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Making the Most Of Your Mixer
1-3. Signal Levels—Decibel Do’s and Don’ts
From the moment you start dealing with things audio, you’ll have to deal with the term “decibel” and its
abbreviation, “dB”. Things can get confusing because decibels are a very versatile unit of measure used
to describe acoustic sound pressure levels as well as electronic signal levels. To make matters worse there
are a number of variations: dBu, dBV, dBm. Fortunately, you don’t need to be an expert to make things
work. Here are a few basics you should keep in mind:
G “Consumer” gear (such as home audio equipment) usually has line inputs and outputs with a nomi-
nal (average) level of –10 dB.
G Professional audio gear usually has line inputs and outputs with a nominal level of +4 dB.
G You should always feed –10 dB inputs with a –10 dB signal. If you feed a +4 dB signal into a –10 dB
input you are likely to overload the input.
G You should always feed +4 dB inputs with a +4 dB signal. A –10 dB signal is too small for a +4 dB
input, and will result in less-than-optimum performance.
G Many professional and semi-professional devices have level switches on the inputs and/or outputs
that let you select –10 or +4 dB. Be sure to set these switches to match the level of the connected
equipment.
G Inputs that feature a “Gain” control—such as the mono-channel inputs on your Yamaha mixer—will
accept a very wide range of input levels because the control can be used to match the input’s sensi-
tivity to the signal. More on this later.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Making the Most Of Your Mixer
Where Your Signal Goes Once It’s Inside the Box
2
At first glance the block diagram of even a modest mixer can look like a space-station schematic. In reality,
block diagrams are a great aid in understanding how the signal flows in any mixer. Here’s a greatly simplified
block diagram of a generic mixer to help you become familiar with the way these things work.
2-1. Greatly Simplified Mixer Block Diagram
Input Channel
Master Section
Signals from the mixer’s
other input channels (if
they are assigned to this
master output or “bus”).
1
2
3
4
5
3 Channel Peak LED & Fader
I Input Channel
The channel peak LED is your most
valuable tool for setting the input “gain”
control for optimum performance. Note
that it is located after the head amp and
EQ stage.
1 Head Amp
The very first stage in any mixer, and
usually the only stage with significant
“gain” or “amplification.” The head
amp has a “gain” control that adjusts
the mixer’s input sensitivity to match the
level of the source. Small signals (e.g.
mics) are amplified, and large signals
are attenuated.
I Master Section
4 Summing Amplifier
This is where the actual “mixing” takes
2 Equalizer
place. Signals from all of the mixer’s
input channels are “summed” (mixed)
together here.
Could be simple bass and treble con-
trols or a full-blown 4-band parametric
EQ. When boost is applied the EQ stage
also has gain. You can actually overload
the input channel by applying too much
EQ boost. It’s usually better to cut than
boost.
5 Master Fader & Level Meter
A stereo, mono, or bus master fader and
the mixer’s main output level meter.
There could be several master faders
depending on the design of the mixer—
i.e. the number of buses or outputs it
provides.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Making the Most Of Your Mixer
The First Steps in Achieving Great Sound
3
Before you even consider EQ and effects, or even the overall mix, it is important to make sure that levels are
properly set for each individual source. This can’t be stressed enough—initial level setup is vitally important for
achieving optimum performance from your mixer! Here’s why … and how.
3-1. The Head Amplifier “Gain” Control Is the Key!
Let’s review our simplified mixer block diagram:
Each and every “stage” in the mixer’s signal path will add a certain amount of noise to the signal: the
head amp, the EQ stage, the summing amplifier, and the other buffer and gain stages that exist in the
actual mixer circuit (this applies to analog mixers in particular). The thing to keep in mind is that the
amount of noise added by each stage is usually not dependent to any significant degree on the level of
the audio signal passing through the circuit. This means that the bigger the desired signal, the smaller the
added noise will be in relation to it. In tech-speak this gives us a better “signal-to-noise ratio”—often
abbreviated as “S/N ratio.” All of this leads to the following basic rule:
To achieve the best overall system S/N ratio, amplify the input to the desired average
level as early as possible in the signal path.
In our mixer, that means the head amplifier. If you don’t get the signal up to the desired level at the head
amplifier stage, you will need to apply more gain at later stages, which will only amplify the noise con-
tributed by the preceding stages. Just remember that too much initial gain is bad too, because it will over-
load our channel circuitry and cause clipping.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Making the Most Of Your Mixer
3-2. Level Setup Procedure For Optimum Performance
Now that we know what we have to do, how do we do it? If you take another quick look at the mixer
block diagram you’ll notice that there’s a peak indicator located right after the head amplifier and EQ
stages, and therein lays our answer! Although the exact procedure you use will depend on the type of
mixer you use and the application, as well as your personal preferences, here’s a general outline:
Start by setting all level controls to their minimum: master fad-
ers, group faders (if provided), channel faders, and input gain
1
controls. Also make sure that no EQ is applied (no boost or
cut), and that all effects and dynamic processors included in
the system are defeated or bypassed.
Apply the source signal to each channel one at a time: have
singers sing, players play, and playback devices play back at
2
the loudest expected level. Gradually turn up the input gain
control while the signal is being applied to the corresponding
channel until the peak indicator begins to flash, then back off
a little so that the peak indicator flashes only occasionally.
Repeat for each active channel.
Raise your master fader(s)—and group faders if available—to
their nominal levels (this will be the “0” markings on the fader
scale).
3
Now, with all sources playing, you can raise the channel fad-
ers and set up an initial rough mix.
4
That’s basically all there is to it. But do keep your eyes on the main output level meters while setting up
the mix to be sure you don’t stay in the “peak zone” all the time. If the output level meters are peaking
constantly you will need to lower the channel faders until the overall program falls within a good range—
and this will depend on the “dynamic range” of your program material.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Making the Most Of Your Mixer
External Effects, Monitor Mixes, and Groups
4
Pre/Post—What’s the difference?
4-1. AUX Buses For Monitor Sends and
Overall Effects
pre
post
There are a number of reasons why you might
want to “tap” the signal flowing through your
mixer at some point before the main outputs: the
two most common being 1) to create a monitor
mix that is separate from the main mix, and 2) to
process the signal via an external effect unit and
then bring it back into the mix. Both of these func-
tions, and more, can be handled by the mixer’s
AUX (Auxiliary) buses and level controls. If the
mixer has two AUX buses, then it can handle both
functions at the same time. Larger mixing con-
soles can have 6, 8, or even more auxiliary buses
to handle a variety of monitoring and processing
needs.
A “pre-fader” signal is taken
A
“post-fader” signal is
from a point before the taken from a point after the
channel fader, so the send channel fader, so its level
level is affected only by the will be affected by both the
AUX send level control and AUX send level control and
not by the channel fader.
the channel fader.
Pre-fader sends are most Post-fader sends are most
commonly used to provide commonly used in conjunc-
monitor mixes.
tion with the mixer’s AUX or
effect returns for external
effect processing.
Using the AUX buses and level controls is pretty
straightforward. The only thing you need to con-
sider is whether you need a “pre-fader” or “post-
fader” send. AUX sends often feature a switch that
allows you to configure them for pre- or post-
fader operation.
Pre-fader send for a monitor mix. The send signal is fed to the monitor power amplifier and speaker system.
The channel fader does not affect the send level so the monitor mix remains independent of the main mix. No
return signal is used in this case.
Channel
Fader
Master
Fader
AUX Send
Level
AUX Send Level
AUX Return Level
Post-fader send for external effects processing. The send signal is fed to the external effect unit—a reverb
unit, for example—and the output from the effect unit is returned to the AUX Return jack and mixed back into the
main program. The send level is affected by the channel fader so the effect level always remains in proportion to
the channel signal.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Making the Most Of Your Mixer
4-2. Using Groups
Group buses and faders can greatly simplify the mixing process—particularly in live situations in which
changes have to be made as quickly as possible. If you have a group of channels that need to be adjusted
all together while maintaining their relative levels, grouping is the way to go. Simply assign the group to a
group bus, and make sure that group is also assigned to the main program bus. Then you can adjust the
overall level of the group using a single group fader, rather than having to attempt to control multiple
channels faders simultaneously.
Group buses usually also have their own outputs, so you can send the group signal to a different external
destination from the main mix.
Channel faders Assigned to Group
(Controlled As a Group)
A group of channels whose levels need to
maintain the same relationship—a drum mix, for
example—can be assigned to a group bus.
Usually the group bus signal can be output
independently via “Group” outputs, or it can be
assigned to the main program (stereo) bus to be
mixed in with the main stereo program.
Once the mix between the channels assigned to
the group is established via the channel faders,
the overall level of the entire group can be
conveniently adjusted via a single group fader.
Group
Fader
Channel faders Assigned to Stereo
(Controlled Individually)
Stereo
Master
Fader
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Making the Most Of Your Mixer
4-3. Channel Inserts for Channel-specific Processing
Another way to get the mixer’s signal outside the box is to use the channel inserts. The channel inserts are
almost always located before the channel fader and, when used, actually “break” the mixer’s internal sig-
nal path. Unlike the AUX sends and returns, the channel insert only applies to the corresponding chan-
nel. Channel inserts are most commonly used for applying a dynamics processor such as a compressor or
limiter to a specific channel—although they can be used with just about any type of in/out processor.
Channel
Fader
When a plug is inserted into the channel insert jack, the inter-
nal signal path is interrupted and sent outside the mixer for
external processing.
Channel insert jacks must be used with a special insert cable that has a TRS phone jack on one end and
mono phone jacks on the split “Y” end. One of the mono phone jacks carries the “send” signal to be fed
to the input of the external processor, and the other carries the “return” signal from the output of the pro-
cessor.
To the input jack of the
external processor
To the INSERT I/O jack
Sleeve Tip
Sleeve
Ring
To the output jack of
Tip
the external processor
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Making the Most Of Your Mixer
Making Better Mixes
5
Music First—Then Mix
5-1. Approaching the Mix—Where Do
You Start?
In any case, the music comes first. Think about
the music and let it guide the mix, rather than try-
ing to do things the other way around. What is the
music saying and what instrument or technique is
being used to drive the message? That’s where the
focus of your mix should be. You’re using a high-
tech tool to do the mixing, but the mix itself is as
much art as the music. Approach it that way and
your mixes will become a vital part of the music.
Mixing is easy, right? Just move the faders around
until it sounds right? Well, you can do it that way,
but a more systematic approach that is suited to
the material you’re mixing will produce much
better results, and faster. There are no rules, and
you’ll probably end up developing a system that
works best for you. But the key is to develop a
system rather than working haphazardly. Here are
a few ideas to get you started:
5-2. Panning For Cleaner Mixes
Faders Down
Not only does the way you pan your individual
channels determine where the instruments appear
in the stereo sound field, but it is also vital to give
each instrument it’s own “space” so that it doesn’t
conflict with other instruments. Unlike live sound
in a real acoustic space, recorded stereo sound is
basically 2-dimensional (although some types of
surround sound are actually very 3-dimensional),
and instruments positioned right on top of each
other will often get in each other’s way—particu-
larly if they are in the same frequency range or
have a similar sound.
It might sound overly simple, but it is usually a
good idea to start with all channel faders off—all
the way down. It’s also possible to start with all
faders at their nominal settings, but it’s too easy to
lose perspective with this approach. Start with all
faders down, then bring them up one by one to fill
out the mix. But which channel should you start
with?
Example1:
Vocal Ballad Backed by Piano Trio
What are you mixing? Is it a song in which the
vocals are the most important element? If so you
might want to build the mix around the vocals.
This means bringing the vocal channel up to
nominal first (if your level setup procedure has
been done properly this will be a good starting
point), and then adding the other instruments.
What you add next will depend on the type of
material you are working with and your approach
to it. If the vocals are backed by a piano trio and
the song is a ballad, for example, you might want
to bring in the piano next and get the vocal/piano
relationship just right, then bring in the bass and
drums to support the overall sound.
Example2:
Funky R&B Groove
The approach will be totally different if you’re
mixing a funky R&B number that centers on the
groove. In this case most engineers will start with
the drums, and then add the bass. The relation-
ship between the drums and bass is extremely
important to achieve the “drive” or groove the
music rides on. Pay particular attention to how
the bass works with the kick (bass drum). They
should almost sound like a single instrument—
with the kick supplying the punch and the bass
supplying the pitch. Once again, there are no
rules, but these are concepts that have been
proven to work well.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Making the Most Of Your Mixer
One of the biggest problems with too much boost
is that it adds gain to the signal, increasing noise
and potentially overloading the subsequent cir-
cuitry.
Spread them Out!
Position your instruments so they have room to
“breathe,” and connect in the most musical way
with other instruments. Sometimes, however,
you’ll want to deliberately pan sounds close
together, or even right on top of one another, to
emphasize their relationship. There are no hard-
and-fast rules. Normally (but this is not a rule),
bass and lead vocals will be panned to center, as
will the kick drum if the drums are in stereo.
5-4. Ambience
Judicious application of reverb and/or delay via
the mixer’s AUX busses can really polish a mix,
but too much can “wash out” the mix and reduce
overall clarity. The way you set up your reverb
sound can make a huge difference in the way it
meshes with the mix.
5-3. To EQ Or Not To EQ
In general: less is better. There are many situations
in which you’ll need to cut certain frequency
ranges, but use boost sparingly, and with caution.
Proper use of EQ can eliminate interference
between instruments in a mix and give the overall
sound better definition. Bad EQ—and most com-
monly bad boost—just sounds terrible.
Reverb/Delay Time
Different reverb/delay units offer different capabil-
ities, but most offer some means of adjusting the
reverb time. A little extra time spent matching the
reverb time to the music being mixed can mean
the difference between great and merely average
sound. The reverb time you choose will depend
to a great degree on the tempo and “density” of
the mix at hand. Slower tempos and lower densi-
ties (i.e. sparser mixes with less sonic activity) can
sound good with relatively long reverb times. But
long reverb times can completely wash out a
faster more active piece of music. Similar princi-
ples applies to delay.
Cut For a Cleaner Mix
For example: cymbals have a lot of energy in the
mid and low frequency ranges that you don’t
really perceive as musical sound, but which can
interfere with the clarity of other instruments in
these ranges. You can basically turn the low EQ
on cymbal channels all the way down without
changing the way they sound in the mix. You’ll
hear the difference, however, in the way the mix
sounds more “spacious,” and instruments in the
lower ranges will have better definition. Surpris-
ingly enough, piano also has an incredibly power-
ful low end that can benefit from a bit of low-
frequency roll-off to let other instruments—nota-
bly drums and bass—do their jobs more effec-
tively. Naturally you won’t want to do this if the
piano is playing solo.
Reverb Tone
How “bright” or “bassy” a reverb sound is also
has a huge impact on the sound of your mix. Dif-
ferent reverb units offer different means of con-
trolling this—balance between the high- and low-
frequency reverb times, simple EQ, and others. A
reverb that is too bright will not only sound unnat-
ural, but it will probably get in the way of delicate
highs you want to come through in your mix. If
you find yourself hearing more high-end reverb
than mix detail, try reducing the brightness of the
reverb sound. This will allow you to get full-bod-
ied ambience without compromising clarity.
The reverse applies to kick drums and bass gui-
tars: you can often roll off the high end to create
more space in the mix without compromising the
character of the instruments. You’ll have to use
your ears, though, because each instrument is dif-
ferent and sometimes you’ll want the “snap” of a
bass guitar, for example, to come through.
Reverb Level
It’s amazing how quickly your ears can lose per-
spective and fool you into believing that a totally
washed-out mix sounds perfectly fine. To avoid
falling into this trap start with reverb level all the
way down, then gradually bring the reverb into
the mix until you can just hear the difference. Any
more than this normally becomes a “special
effect.” You don’t want reverb to dominate the
mix unless you are trying to create the effect of a
band in a cave—which is a perfectly legitimate
creative goal if that’s the sort of thing you’re aim-
ing for.
Boost With Caution
If you’re trying to create special or unusual
effects, go ahead and boost away as much as you
like. But if you’re just trying to achieve a good-
sounding mix, boost only in very small incre-
ments. A tiny boost in the midrange can give
vocals more presence, or a touch of high boost
can give certain instruments more “air.” Listen,
and if things don’t sound clear and clean try using
cut to remove frequencies that are cluttering up
the mix rather than trying to boost the mix into
clarity.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Front & Rear Panels
1 GAIN Control
Channel Control Section
Adjusts the input signal level.
To get the best balance between the S/N ratio and the dynamic
range, adjust the level so that the peak indicator (2) comes on
only at about maximum input level.
The –60 to –16 scale indicates the MIC input adjustment level.
The –34 to +10 scale indicates the LINE input adjustment
level.
Channels
1 to 8 (MG16/4)
1 to 4 (MG12/4)
(Monaural)
Channels
9/10 to 15/16 (MG16/4)
5/6 to 11/12 (MG12/4)
(Stereo)
2 PEAK Indicator
Detects the peak level of the post-EQ signal, and lights up red
when the level reaches 3 dB below the clipping level. For
XLR-equipped stereo input channels (9/10 and 11/12 on the
MG16/4; 5/6 and 7/8 on the MG12/4), detects both post-EQ
and post-mic-amp peak levels, and lights red if either of these
levels reaches 3 dB below the clipping level.
1
2
3 2
3
3
Switch (High Pass Filter)
This switch toggles the HPF on or off. To turn the HPF on,
4
press the switch in (
80 Hz.
). The HPF cuts frequencies below
4 Equalizer (HIGH, MID, and LOW)
This three-band equalizer adjusts the channel’s high, mid, and
low frequency bands. Setting the knob to the
position pro-
duces a flat frequency response. Turning the knob to the right
boosts the corresponding frequency band, while turning to the
left attenuates the band. The following table shows the EQ
type, base frequency, and maximum cut/boost for each of the
three bands.
6
6
5
5
7
Band
HIGH
MID
Type
Base Frequency Maximum Cut/Boost
10 kHz
Shelving
Peaking
Shelving
8
2.5 kHz
100 Hz
15 dB
LOW
5 AUX1 and AUX2 Controls
The AUX1 knob controls the signal level that the channel sends
to the AUX1 bus; the AUX2 knob controls the signal level to
the AUX2 bus. The knob should generally be set close to the
position.
9
9
0
0
If you are using stereo channels, the signals from the L (odd)
and R (even) channels are mixed and sent to the AUX1 and
AUX2 buses.
Allows you to output the signal to the buses regard-
less of the setting of the ST switch 8.
NOTE
A
A
Note: Within this manual, all panel illustrations show the
MG16/4 panel.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Front & Rear Panels
6 PRE Switch
Selects whether the pre-fader or the post-fader signal is fed to
the AUX1 bus. If you set the switch on (
), the mixer sends
the pre-fader signal (the signal prior to passage though channel
fader A) to the AUX1 bus, so that AUX1 output is not affected
by the fader. If you set the switch off (
post-fader signal to the AUX1 bus.
) the mixer sends the
Note that this switch applies to AUX1 only. The signal to the
AUX2 bus always passes through the channel fader first.
7 PAN Control (MG16/4: CHs 1 to 8.
MG12/4: 1 to 4.)
PAN/BAL Control (MG16/4: 9/10 and 11/12.
MG12/4: 5/6 and 7/8.)
BAL Control (MG16/4: 13/14 and 15/16.
MG12/4: 9/10 and 11/12.)
The PAN control determines the positioning of the channel’s
signal on the Group 1 and 2 buses or on the Stereo L and R
buses.
The BAL control knob sets the balance between left and right
channels. Signals into to the L input (odd channel) feed to the
Group 1 bus or to the Stereo L bus; signals into the R input
(even channel) feed to the Group 2 bus or the Stereo R bus.
On channels where this knob provides both PAN
and BAL controls (9/10 and 11/12 on the MG16/4;
NOTE
5/6 and 7/8 on the MG12/4), the knob operates as a
PAN control if you are inputting through the MIC
jack or into the L (MONO) input only, and operates
as a BAL control if you are inputting into both L and
R inputs.
8
ST Switch
This switch assigns the channel’s signal to the Stereo L and R
buses. To send the signal to the Stereo bus, set the switch on by
pressing it in (
it is on.
). The switch lights up orange to indicate that
9 PFL (Pre-Fader Listen) Switch
This switch lets you monitor the channel’s pre-fader signal. To
set the switch on, press it in (
) so that it lights up. When the
switch is on, the mixer outputs the channel’s pre-fader signal to
the PHONES and C-R OUT jacks, for monitoring.
0 GROUP Switch
Use this switch to assign the channel’s signal to the Group out-
put. Press the switch in (
1 and 2 buses.
) to output the signal to the Group
Allows you to output the signal to the buses regard-
less of the setting of the ST switch 8.
NOTE
A Channel Fader
Adjusts the output level of the signal being input to the chan-
nel. Use these faders to adjust the volume balance among the
various channels.
To reduce noise, set the fader sliders for unused
channels all the way down.
NOTE
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Front & Rear Panels
1 ST Master Fader
Master Control Section
Adjusts the signal level to the ST OUT jacks.
2 GROUP 1-2 Fader
Adjusts the signal level to the GROUP OUT 1 and GROUP
OUT 2 jacks.
B
A
6
7
3 TO ST Switch
If this switch is on (
), the mixer sends the signals processed
by the GROUP 1-2 fader (2) onto the Stereo bus. The Group 1
signal goes to Stereo L and the Group 2 signal goes to Stereo
R.
4 Master SEND (AUX1 and AUX2 Controls)
Adjust the signal level, respectively. These are the signals that
are output to the AUX1 and AUX2 SEND jacks.
0
5 RETURN (AUX1, AUX2, and ST Controls)
• AUX1 and AUX2 Controls
Adjust the level of the mixed L/R signal sent from the
RETURN jacks (L (MONO) and R) to the AUX1 and AUX2
buses.
• ST Control
Adjust the level of the signal sent from the RETURN jacks (L
(MONO) and R) to the Stereo bus.
9
8
If you supply a signal to the RETURN L (MONO)
jack only, the mixer outputs the identical signal to
both the L and R Stereo buses.
4
NOTE
6 2TR IN Control
5
Adjusts the level of the signal sent from the 2TR IN jack to the
Stereo bus.
3
2
7 PHANTOM +48 V Switch
1
This switch toggles phantom power on and off. If you set the
switch on, the mixer supplies power to all channels that provide
XLR mic input jacks (CHs 1–8, 9/10, 11/12 on MG16/4, 1–4,
5/6, 7/8 on MG12/4). Set this switch on when using one or
more condenser microphones.
When this switch is on, the mixer supplies DC +48 V
power to pins 2 and 3 of all XLR-type MIC INPUT
NOTE
jacks.
• Be sure to leave this switch OFF when you are not
using phantom power. Humming or damage may
result if you connect to an unbalanced device or to
an ungrounded transformer while this switch is on.
But note that the switch may be left on without
problem when connecting to balanced dynamic
microphones.
• To avoid damage to speakers, be sure to turn this
switch off (
ing cables.
) before connecting or disconnect-
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Front & Rear Panels
8 Level-Meter Signal Switches (ST-GROUPToggle
Switch and 2TR IN Switch)
These level-meter switches, together with the channel PFL
switches, select the signal that is sent through the
C-R/PHONES control to the C-R OUT jacks, the PHONES
jack, and the level meter.
The following illustration shows how the switch settings corre-
spond to the signal selection.
1
2
Switch
PFL
2TR IN ST-GROUP
Signal
ON
PFL
ON
2TR IN
C-R OUT
&
OFF
PHONES
ON
GROUP
OFF
OFF
ST
1
If the input channel’s PFL switch is on (
), then only the
channel’s PFL output it sent to the C-R OUT jacks, PHONES
jacks, and level meter.
2
If the 2TR IN switch is ON (
), the signal supplied to the 2TR
IN jack is sent to the C-R OUT jacks, PHONE jacks, and level
meter. If the 2TR IN switch is OFF, then the Group or Stereo
signal is sent instead (as determined by the ST-GROUP toggle
switch).
9 C-R/PHONES Control
Controls the level of the signal output to the PHONES jack and
the C-R L and R jacks.
0 Level Meter
This LED display shows the level of the signal selected by the
selection switches described in 8 above (the level to the C-R
OUT and PHONES jacks). The “0” point corresponds to the
standard output level. The indicator lights up red when the out-
put hits the clipping level.
A POWER Indicator
This indicator lights up when the mixer’s power is ON.
B PHONES jack
Connector for headphones. This is a stereo phone-type output
jack.
The signal monitored by these jacks is selected by
the settings of the ST-GROUP toggle switch, the
NOTE
2TR IN switch, and the PFL switches on the input
channels.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Front & Rear Panels
Rear Input/Output Section
6
7 8 9 0
3
2
A B
5
4
1
1 Channel Input jacks
3 Channel Input jacks
• MIC jacks (MG16/4: CHs 1 to 8, 9/10, 11/12. MG12/4:
CHs 1 to 4, 5/6, 7/8)
These are balanced XLR-type microphone input jacks
These are unbalanced stereo line input jacks. Two jack types
are provided: phone type (MG16/4: CHs 9/10 to 15/16;
MG12/4: CHs 5/6 to 11/12) and RCA pin type (MG16/4: CHs
13/14, 15/16; MG12/4: CHs 9/10, 11/12).
(1:Ground; 2:Hot; 3:Cold).
• LINE jacks (MG16/4: CHs 1 to 8. MG12/4: CHs 1 to 4)
These are balanced TRS phone-type line input jacks (T: Hot;
R: Cold; S: Ground).
Where a channel provides both a phone jack and an
RCA pin jack, you may use either one of these jacks
NOTE
but you may not use both at the same time. Please
connect to only of these jacks on each channel.
You can connect either balanced or unbalanced phone plugs
to these jacks.
4 GROUP OUT (1, 2) Jacks
Where an input channel provides both a MIC INPUT
jack and a LINE INPUT jack, you may use either
one of these jacks but you may not use both at the
same time. Please connect to only one of these
jacks on each channel.
NOTE
These are impedance-balanced phone-type output jacks that
output the Group 1-2 signals. Use these jacks to connect to the
input jacks of an MTR, external mixer, or other such device.
5 ST OUT (L, R) Jacks
2 INSERT I/O Jacks
These jacks deliver stereo output of the mixed signal. You use
these jacks, for example, to connect to the power amplifier
driving your main speakers. You also use these jacks when you
wish to record the signal utilizing the level control applied by
the ST fader in the Master Control section.
• XLR jacks
Each of these jacks is positioned between the equalizer and
fader of the corresponding input channel (MG16/4: CHs 1 to 8;
MG12/4: CHs 1 to 4). These jacks can be used to indepen-
dently connect these channels to devices such as graphic equal-
izers, compressors, and noise filters. These are TRS (tip, ring,
sleeve) phone jacks that support bidirectional operation.
XLR-type balanced output jacks.
Connection to an INSERT I/O jack requires a spe-
cial separately-sold insertion cable such as illus-
• Line jacks
TRS phone-type balanced output jacks.
NOTE
trated below.
6 C-R OUT Jacks
To the input jack of the external processor
Use these stereo phone-type output jacks to connect to your
monitor system.
To the INSERT I/O jack
The signal monitored by these jacks is selected by
the settings of the ST-GROUP toggle switch, the
Sleeve
Tip
NOTE
2TR IN switch, and the PFL switches on the input
channels.
Sleeve
Ring
To the output jack of the external processor
Tip
7 SEND Jacks
• AUX1, AUX2
The signal output from the INSERT I/O jacks is
reverse-phased. This will not be a problem if con-
necting the jack to an effector. If using the jack to out-
put to an external device, however, please be aware
of possible phase conflicts with other signals.
These are impedance balanced phone-type output jacks.
These jacks output the signals from the AUX1 and AUX2,
respectively. Use these jacks to output these signals to an
effector or a cue box or other such monitor system.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Front & Rear Panels
8 RETURN L (MONO), R Jacks
0 2TR IN Jacks
These are unbalanced phone-type line input jacks. The signal
received by these jacks is sent to the Stereo bus and the AUX1
and AUX2 buses. These jacks are typically used to receive a
return signal from an external effector (reverb, delay, etc.).
These RCA pin jacks input a stereo sound source. Use these
jacks when you want to connect a CD or DAT directly to the
mixer for monitoring.
You can adjust the signal level using the 2TR IN
NOTE
control in the Master Control section.
These jacks can also be used as an auxiliary stereo
NOTE
input. If you connect to the L(MONO) jack only, the
A POWER Switch
mixer will recognize the signal as monaural and will
propagate the identical signal on both L and R
jacks.
Use this switch to set mixer power to ON or STANDBY.
Note that trace current continues to flow while the
switch is in the STANDBY position. If you do not plan
to use the mixer again for a long while, be sure to
unplug the adaptor from the wall outlet.
9 REC OUT (L, R) Jacks
By connecting these jacks to an external DAT recorder or cas-
sette recorder, you can record the same signal that is being out-
put from the ST OUT jacks.
The mixer’s ST Master Fader has no affect on the
signal output from these jacks. Be sure to make
appropriate level adjustments at the recording
device side.
B AC ADAPTOR IN Connector
NOTE
Connects to the included PA-20 power adaptor (see page 5).
Use only the PA-20 adaptor included with this mixer.
Use of a different adaptor may result in fire or electric
shock.
Connector Polarities
INPUT
OUTPUT
Pin 1: Ground
MIC INPUT, ST OUT
Pin 2: Hot (+)
Pin 3: Cold (–)
LINE INPUT (monaural channels),
GROUP OUT, ST OUT, C-R OUT
Tip: Hot (+)
Ring: Cold (–)
Sleeve: Ground
AUX1, AUX2
*
Ring
Tip: Output
INSERT I/O
Ring: Input
Sleeve: Ground
Sleeve
Tip
Tip: L
PHONES
RETURN
Ring: R
Sleeve: Ground
Tip: Hot
LINE INPUT (stereo channels)
Sleeve: Ground
Sleeve
Tip
*
These jacks will also accept connection to monaural phone plugs. If you use monaural plugs, the connection will be unbalanced.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Setting Up
Where an input channel provides both a MIC INPUT
jack and a LINE INPUT jack, you may use either
one of these jacks but you may not use both at the
same time. Please connect to only one of these
jacks on each channel.
NOTE
Setup Procedure
(1) Before connecting to microphones and instruments, be sure
that all devices are turned off. Also be sure that all of the
mixer’s channel faders and master control faders are set all the
way down.
(2) For each connection, connect one end of the cable to the rele-
vant microphone or instrument and connect the other end to the
appropriate LINE or MIC jack on the mixer.
(3) Power up the devices in the following order: Peripheral devices
→ mixer → power amps → or powered speakers.
When shutting the system down, turn off the power
in the opposite order: Power amps (powered speak-
NOTE
ers) → mixer → peripheral devices.
(LINE jacks on MG16/4: CHs 1 to 8; on MG12/4: 1 to 4. MIC
jacks on MG16/4: CHs 1 to 8, 9/10, 11/12; on MG12/4: 1 to 4,
5/6.)
Setup Examples
I Home Recording
Effector
Effector
Rhythm Machine
Synthesizer
MTR
Effector
Guitar
Sound Source (CD, MD,
DAT, cassette, video, etc.)
Microphone
Powered Monitor
Speakers
Headphones
Personal Computer
MTR
Master Recorder
(MD, CD-R, DAT, etc.)
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Setting Up
I Sound Reinforcement for Live Performance
Monitor Speakers
(Internal)
Drums
Power Amp
Effector
Microphones
Synthesizer
DI
CD, Cassette, or DAT
Recorder
Bass
(
)
CD Player
Effector
DI
Guitar
Microphones
Power Amp
Guitar
Headphones
Main Speakers
(External)
Example of Speaker Arrangement
Stage (Internal)
AUX 1
PRE
(
)
Audience (External)
ST
ST
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Setting Up
Rack Mounting
I Mounting the MG16/4
I Mounting the MG12/4
(1) Two metal rack-mount supports are screwed onto the unit. Use
a screwdriver to remove these supports.
(1) Two metal rack-mount supports are screwed onto the unit. Use
a screwdriver to remove these supports.
(2) Turn the supports over, and fasten them into place again using
the same screws.
(2) Turn the supports over, and fasten them into place again using
the same screws.
(3) Mount the unit into the rack, and fasten it into place.
(3) Mount the unit into the rack, and fasten it into place.
If you wish you may move the left support to the
right side and the right support to the left side, as
shown in the drawing.
Do not install the mixer near power amps or other
heat-generating devices.
NOTE
Do not install the mixer near power amps or other
heat-generating devices.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Appendix
Specifications
I General Specifications
Frequency Characteristics
Total Harmonic Distortion
20 Hz–20 kHz +1 dB, –3 dB @+4 dBu, 600 Ω (with gain control at maximum level)
0.1 % (THD+N) @+14 dBu, 20 Hz–20 kHz, 600 Ω (with gain control at maximum level)
Equivalent input noise 150 Ω (MG16/4: CHs 1 to 8,
MG12/4: CHs 1 to 4)
–128 dBu
–100 dBu
Residual output noise (ST OUT)
ST, GROUP Master fader at nominal level and all Ch
assign SW’s off.
–88 dBu (92 dB S/N)
1
Hum and Noise
AUX master control at nominal level; all channel mix
controls at minimum level.
–81 dBu (85 dB S/N)
–64 dBu (68 dB S/N)
ST, GROUP Master fader and one Ch fader at nominal
level. (MG16/4 CH1–8, MG12/4 CH1–4)
60 dB CH MIC INPUT → CH INSERT OUT
84 dB CH MIC INPUT → GROUP OUT/ST OUT (CH to ST)
94 dB CH MIC INPUT → ST OUT (GROUP to ST)
62.2 dB CH MIC INPUT → REC OUT (CH to ST)
76 dB CH MIC INPUT → AUX SEND (PRE)
86 dB CH MIC INPUT → AUX SEND (POST)
58 dB CH LINE INPUT → GROUP OUT/ST OUT (CH to ST)
84 dB ST CH MIC INPUT → GROUP OUT/ST OUT (CH to ST)
58 dB ST CH LINE INPUT → GROUP OUT/ST OUT (ST to ST)
47 dB ST CH LINE INPUT → AUX SEND (PRE)
57 dB ST CH LINE INPUT → AUX SEND (POST)
34 dB ST CH INPUT → GROUP OUT/ST OUT (ST to ST)
16 dB AUX RETURN → ST OUT
2
Maximum Voltage Gain
9 dB AUX RETURN → AUX SEND
27.8 dB 2TR INPUT → ST OUT
Monaural/Stereo Input Gain Control
Monaural/Stereo High Pass Filter
44 dB variable
80 Hz 12 dB/octave
–70 dB between input channels
–70 dB between input/output channels (CH INPUT)
Crosstalk (1 kHz)
15 dB
Monaural/Stereo Input Channel Equalization:
HIGH 10 kHz shelving
MID 2.5 kHz peaking
LOW 100 Hz shelving
3
Max. Variation
On each channel: red indicator lights if post-EQ signal (on ST channels, if either post-EQ sig-
nal or post-mic-amp signal) comes within 3 dB of the clipping level.
Monaural/Stereo Input Peak Indicator
Level Meters
Two 12-point LED meters
Peak point: red indicator
+5, +3, +1, and 0 points: yellow indicators
–1, –3, –5, –7, –10, –15, –20: green indicators
Phantom +48 VDC Power (Balanced input)
Included Accessory
Supplied when Phantom +48 V switch is ON.
Power adaptor (PA-20)
USA and Canada:
Europe:
Australia:
120 V AC, 60 Hz
230 V AC, 50 Hz
240 V AC, 50 Hz
220 V AC, 60 Hz
Power Supply
Korea:
Power Consumption
Max. Dimensions (W × H × D)
Weight
MG16/4: 36 W
MG12/4: 29 W
MG16/4: 423 × 108 × 416.6 mm
MG12/4: 322 × 108 × 416.6 mm
MG12/4: 5.0 kg
MG16/4: 5.2 kg
Where 0 dBu = 0.775 V and 0 dBV = 1 V
1
Measured with 12.7 kHz, –6 dB/oct. low pass filter (equivalent to 20 kHz, –∞ filter).
(CH MIC INPUT to ST, GROUP OUT/AUX, EFFECT SEND)
2
3
Turning PAN/BAL to left or right.
Shelving turnover/rolloff frequency: 3 dB before maximum cut or boost.
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Appendix
I Input Specifications
Input
Appropriate
Max. Before
Clipping
Connector
Input Connector
Gain
–60
–16
–34
+10
–60
–16
–34
+10
Sensitivity*
Rated Level
Impedance Impedance
Specifications
–80 dBu
(0.078 mV)
–60 dBu
(0.775 mV)
–40 dBu
(7.75 mV)
MIC INPUT
(MG16/4: CHs 1 to 8)
(MG12/4: CHs 1 to 4)
3 kΩ
50–600 Ω mic
600 Ω line
XLR-3-31 type (balanced)
–36 dBu
(12.3 mV)
–16 dBu
(123 mV)
+4 dBu
(1.23 V)
–54 dBu
(1.55 mV)
–34 dBu
(15.5 mV)
–14 dBu
(155 mV)
LINE INPUT
(MG16/4: CHs 1 to 8)
(MG12/4: CHs 1 to 4)
Phone jack (TRS)
(balanced [T: hot; R: cold;
S: ground])
10 kΩ
3 kΩ
–10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
–80 dBu
(0.078 mV)
–60 dBu
(0.775 mV)
–40 dBu
(7.75 mV)
ST CH MIC INPUT
(MG16/4: CH9/CH10,
CH11/CH12)
(MG12/4: CH5/CH6,
CH7/CH8)
50–600 Ω mic
600 Ω line
XLR-3-31 type (balanced)
Phone jack (unbalanced)
–36 dBu
(12.3 mV)
–16 dBu
(123 mV)
–10 dBu
(245 mV)
–54 dBu
(1.55 mV)
–34 dBu
(15.5 mV)
–14 dBu
(155 mV)
ST CH LINE INPUT
(MG16/4: CH9(L)/CH10(R),
CH11(L)/CH12(R))
(MG12/4: CH5(L)/CH6(R),
CH7(L)/CH8(R))
10 kΩ
–10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
ST CH INPUT
(MG16/4: CH13(L)/CH14(R),
CH15(L)/CH16(R))
–30 dBu
–10 dBu
+10 dBu
(2.45 V)
Phone jack (unbalanced);
RCA pin jack
10 kΩ
10 kΩ
600 Ω line
600 Ω line
(24.5 mV)
(245 mV)
(MG12/4: CH9(L)/CH10(R),
CH11(L)/CH12(R))
CH INSERT IN
(MG16/4: CHs 1 to 8)
(MG12/4: CHs 1 to 4)
Phone jack (TRS)
(unbalanced [T: out; R: in;
S: ground])
–20 dBu
(77.5 mV)
0 dBu
(0.775 V)
+20 dBu
(7.75 V)
–12 dBu
+4 dBu
(1.23 V)
+24 dBu
(12.3 V)
Phone jack (TRS) (unbalanced
[T: hot; S: ground])
AUX RETURN (L, R)
2TR IN (L, R)
10 kΩ
10 kΩ
600 Ω line
600 Ω line
(195 mV)
–26 dBV
(50.1 mV)
–10 dBV
(316 mV)
+10 dBV
(3.16 V)
RCA pin jack
Where 0 dBu = 0.775 V and 0 dBV= 1 V
Input sensitivity: the lowest level that will produce the nominal output level when the unit is set to maximum gain.
*
I Output Specifications
Output
Appropriate
Max. Before
Clipping
Output Connectors
Rated Level
Connector Specifications
Impedance Impedance
XLR-3-32 type (balanced)
+24 dBu (12.3 V) Phone jack (TRS)
(balanced [T: hot; R: cold; S: ground])
ST OUT (L, R)
150 Ω
150 Ω
600 Ω line
10 kΩ line
+4 dBu (1.23 V)
Phone jack (TRS)
+20 dBu (7.75 V) (impedance balanced [T: hot; R: cold; S:
ground])
GROUP OUT (1-2)
AUX SEND (1-2)
+4 dBu (1.23 V)
0 dBu (0.775 V)
CH INSERT OUT
(MG16/4: CHs 1 to 8)
(MG12/4: CHs 1 to 4)
Phone jack (TRS)
+20 dBu (7.75 V)
150 Ω
600 Ω
150 Ω
100 Ω
10 kΩ line
10 kΩ line
10 kΩ line
40 Ω phone
(unbalanced [T: out; R: in; S: ground])
REC OUT (L, R)
C-R OUT (L, R)
PHONES
–10 dBV (316 mV) +10 dBV (3.16 V) RCA pin jack
Phone jack (TRS)
+4 dBu (1.23 V)
+20 dBu (7.75 V) (impedance balanced [T: hot; R: cold; S:
ground])
3 mW
75 mW
Stereo phone jack
Where 0 dBu = 0.775 V and 0 dBV= 1 V
Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify
products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale,
please check with your Yamaha dealer.
For European Model
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 6A
Conformed Environment: E1, E2, E3 and E4
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Appendix
Dimensional Diagrams
I MG16/4
393
428
H 108
101.3
3
W 423
480
When mounted on rack
I MG12/4
H 108
102.6
W 322
2
322
317.4
480
When mounted on rack
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Appendix
Block Diagram and Level Diagram
MG16/4, MG12/4
Download from Www.Somanuals.com. All Manuals Search And Download.
30
For details of products, please contact your nearest Yamaha or the
authorized distributor listed below.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
Para detalles sobre productos, contacte su tiendaYamaha más cercana
o el distribuidor autorizado que se lista debajo.
BELGIUM/LUXEMBOURG
NORTH AMERICA
ASIA
Yamaha Music Central Europe GmbH,
CANADA
INDONESIA
Branch Belgium
Rue de Geneve (Genevastraat) 10, 1140 - Brussels,
Belgium
Tel: 02-726 6032
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
Tel: 416-298-1311
FRANCE
Yamaha Musique France, S.A.
Division Professionnelle
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
U.S.A.
KOREA
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Yamaha Music Korea Ltd.
Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,
Youngdungpo-ku, Seoul, Korea
Tel: 02-3770-0661
Tel: 714-522-9011
ITALY
Yamaha Musica Italia S.P.A.
Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
MALAYSIA
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de Mexico S.A. De C.V.,
Departamento de ventas
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-703-0900
SPAIN/PORTUGAL
Javier Rojo Gomez No.1149, Col. Gpe Del
Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.
Tel: 686-00-33
Yamaha-Hazen Música, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-201-0700
SINGAPORE
Yamaha Music Asia Pte., Ltd.
11 Ubi Road #06-00, Meiban Industrial Building,
Singapore
BRAZIL
Yamaha Musical do Brasil LTDA.
Av. Rebouças 2636, São Paulo, Brasil
Tel: 011-853-1377
SWEDEN
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1
Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
Tel: 65-747-4374
TAIWAN
Yamaha KHS Music Co., Ltd.
10F, 150, Tun-Hwa Northroad,
Taipei, Taiwan, R.O.C.
ARGENTINA
Yamaha de Panamá S.A. Sucursal de Argentina
Viamonte 1145 Piso2-B 1053,
Buenos Aires, Argentina
Tel: 02-2713-8999
DENMARK
YS Copenhagen Liaison Office
Generatorvej 8B
DK-2730 Herlev, Denmark
Tel: 44 92 49 00
THAILAND
Tel: 1-4371-7021
Siam Music Yamaha Co., Ltd.
121/60-61 RS Tower 17th Floor,
Ratchadaphisek RD., Dindaeng,
Bangkok 10320, Thailand
Tel: 02-641-2951
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1
N-1345 Østerås, Norway
Tel: 67 16 77 70
Yamaha de Panamá S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co., Ltd.
Shanghai Branch
United Plaza 25F 1468 Nan Jing Road West, Jingan
Shanghai 200040, China
Tel: 507-269-5311
OTHER EUROPEAN COUNTRIES
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
Tel: 86-21-6247-2211
EUROPE
THE UNITED KINGDOM
Yamaha-Kemble Music (U.K.) Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
OTHER ASIAN COUNTRIES
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2313
AFRICA
Yamaha Corporation,
Tel: 01908-366700
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2313
GERMANY
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Central Europe GmbH,
Branch Switzerland
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
AUSTRIA
Yamaha Music Central Europe GmbH,
Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
Yamaha Corporation,
OTHER COUNTRIES
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2313
Yamaha Music Gulf FZE
LB21-128 Jebel Ali Freezone
P.O.Box 17328, Dubai, U.A.E.
Tel: 971-4-881-5868
THE NETHERLANDS
Yamaha Music Central Europe GmbH,
Branch Nederland
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2441
PA01
Download from Www.Somanuals.com. All Manuals Search And Download.
Yamaha Manual Library
M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
© 2002 Yamaha Corporation
V981800 210CRCR5.3-01A0
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|