U
DVD/Video CD/CD Player
DV-S5270
Operating Instructions
Before connecting, operating or adjusting this product,
please read these instructions completely.
Please keep this manual for future reference.
VQT8678-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
Note
Use this player only in areas with the same power supply.
Units for the U.S.A. and Canada: AC 120 V, 60 Hz.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
DVD/VIDEO CD/CD PLAYER IS A CLASS I LASER
PRODUCT. HOWEVER THIS DVD/VIDEO CD/CD
PLAYER USES A VISIBLE LASER BEAM WHICH
COULD CAUSE HAZARDOUS RADIATION EXPO-
SURE IF DIRECTED. BE SURE TO OPERATE THE
DVD/VIDEO CD/CD PLAYER CORRECTLY AS IN-
STRUCTED.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALI-
FIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous volt-
age” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
GingSarted
WHEN THIS DVD/VIDEO CD/CD PLAYER IS
PLUGGED TO THE WALL OUTLET, DO NOT
PLACE YOUR EYES CLOSE TO THE OPENING OF
THE DISC TRAY AND OTHER OPENINGS TO LOOK
INTO THE INSIDE OF THIS PLAYER.
The exclamation point within an equilateral trian-
gle is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the ap-
pliance.
USE OF CONTROLS OR ADJUSTMENTS OR PER-
FORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZ-
ARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
CAUTION -LASER RADIATION WHEN OPEN.
DO NOT STARE INTO BEAM.
ATTENTION-RAYONNEMENT LASER EN CAS D'OUVERTURE.
NE PAS REGARDER DANS LE FAISCEAU.
VORSICHT -LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET.
NICHT IN DEN STRAHL BLICKEN.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PLAYER TO RAIN
OR MOISTURE.
ADVARSEL -LASERSTRÅLING VED ÅBNING.
SE IKKE IND I STRÅLEN.
ADVARSEL -LASERSTRÅLING NÅR DEKSEL ÅPNES.
STIRR IKKE INN I STRÅLEN.
VARNING -LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD.
STIRRA EJ IN I STRÅLEN.
VARO!
-AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE.
ÄLÄ TUIJOTA SÄTEESEEN.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
AND ANNOYING INTERFERENCE, USE THE RECOM-
MENDED ACCESSORIES ONLY.
注意
- ここを開くとレーザー光が出ます。
レーザー光をのぞき込まないでください。
(Inside of player)
This player is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this player
itself is turned off. This state is called the standby mode.
In this state, this player is designed to consume a very small
quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
FCC INFORMATION (for US customers only)
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion—and, most importantly, without affecting your
sensitive hearing. Since hearing damage from
loud sounds is often undetectable until it is too
late, YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This
product, when installed as indicated in the instructions contained
in this manual, meets FCC requirements. Modifications not ex-
pressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a
reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with
other electronic devices.
from excessive volume levels.
GnigSarted
This equipment generates/uses radio frequencies and, if not in-
stalled and used according to the instructions found in the users
manual, may cause interference harmful to the operation of other
electronic devices.
Compliance with FCC regulations does not guarantee that inter-
ference will not occur in all installations. If this product is found to
be the source of interference, which can be determined by turning
the unit “OFF” and “ON”, please try to eliminate the problem by
using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the an-
tenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control preparations
A
B
A
»
Battery installation
R6/LR6, AA, UM-3
Use of batteries
³Align the poles (i and j) properly when inserting the batteries.
³Do not mix old and new batteries or different types of batteries.
³Do not recharge ordinary dry cell batteries.
³Do not heat or disassemble the batteries. Do not allow them to con-
tact flame or water.
³Remove the batteries if the unit is not to be used for a long time.
³Do not keep together with metallic objects such as necklaces.
³Do not use rechargeable type batteries.
³Do not use batteries if the covering has been peeled off.
Mishandling of batteries can cause electrolyte leakage which can
damage items the fluid contacts and may cause a fire.
If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any
part of your body.
GingSarted
Remote control signal sensor
B
»
Correct method of use
Operation notes
About 23 feet
(7 meters)
in front of the
signal sensor
³Do not place obstacles between the remote control signal sensor
and remote control unit.
³Do not expose the remote control signal sensor to direct sunlight or
to the bright light of a fluorescent light.
30°
30°
³Take care to keep the remote control signal sensor and end of the
remote control unit free from dust.
³If this system is installed in a rack with glass doors, the glass doors’
thickness or color might make it necessary to use the remote con-
trol a shorter distance from the system.
Transmission
window
To prevent damage
³Never place heavy items on top of the unit.
³Do not disassemble or reconstruct the unit.
³Do not spill water or other liquids into the unit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc information
Discs not supported by this
player
Discs supported by this player
DVD-Video
Video CD
Audio CD
3q (8 cm) disc/
5q (12 cm) disc
³Do not try to play Photo CD or CD-R.
(Data on the disc may be damaged.)
³DVD with region number other than “1” or “ALL”
³PAL discs
³DVD-ROM
³DVD-R
³DVD-RW
³SVCD
³CD-G
³Divx Video Disc
³DVD-Audio
³DVDiRW
³CVD
3q (8 cm) disc/
5q (12 cm) disc
³CD-RW
³DVD-RAM
³CD-ROM
³SACD
³VSD
3q (8 cm) disc/
5q (12 cm) disc
³CDV
etc.
GnigSarted
For the purpose of these operating instructions, “DVD” stands for DVD-Video and “CD” stands for Audio CD.
º Region number supported by this player
Region numbers are allocated to DVD players and software accord-
ing to where they are sold.
³The region number of this player is “1”.
³The player will play DVDs marked with labels containing the region
number “1” or “ALL”.
º Terms used in these operating instructions
³Title/Chapter [DVD]
DVDs are divided up into large sections, titles, and smaller sections,
chapters. The numbers allocated to these sections are called title
numbers and chapter numbers.
Example:
Title 1
Title 2
Example:
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
1
3
1 ALL
4
etc.
³Track [VCD] [CD]
Video CDs and CDs are divided up into sections called tracks, and
the numbers allocated to these sections are called track numbers.
º Playing DVDs and Video CDs
The producer of the material can control how these discs are played.
This means that you may not be able to control play of a disc with
some operations described in these operating instructions. Read the
disc’s instructions carefully.
Example:
Track 1 Track 2 Track 3 Track 4 Track 5
Example: ³“/” appears when you press the skip buttons to move
to the next section.
³Resume, repeat play, and markers may not work during
play of interactive DVDs and menu play of Video CDs
with playback control.
³After showing the Karaoke menu, tracks are played
successively without returning to the menu (Video CD
with playback control).
³Playback control [VCD]
If a Video CD has “playback control” written on its disc or jacket, it
means that particular scenes or information can be selected for
viewing interactively with the TV monitor using the menu screen.
This player can play Video CDs with playback control.
Using menus to control play of a Video CD is called “menu play” in
these operating instructions.
º Marks used in these operating instructions
[DVD]: indicates features applicable to DVD only.
[VCD]: Video CD only.
Display during menu play of a Video CD with playback control
[CD] : CD only.
³Interactive DVD [DVD]
An interactive DVD is DVD software which includes multiple angles,
multiple plot endings, etc. The elapsed play time of some of these
DVDs is not shown.
Display during play of an interactive DVD
DVD
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Control reference guide
Buttons such as 1 function in exactly
the same way as the buttons on the
player.
1
2
3
4 5 6
NATURAL SOUND DVD PLAYER
1
POWER
H/I
OPEN/CLOSE
STANDBY/ON
f
OPEN/CLOSE
3
4
P
6
DVD
/
VIDEO CD / CD
STOP
∫
PAUSE
;
PLAY
1
:
SKIP
;
C
SEARCH
D
D
I
G
I
T
A
L
V.S.S.
SLOW/
SEARCH
SKIP
5
9
G
H
I
J
K
L
M
:
9
6
5
TOP MENU
MENU
Q
R
7
8
9
:
ENTER
GingSarted
ON SCREEN
RETURN
S
T
PLAY MODE SUBTITLE AUDIO ANGLE
; < =>
?
@
REPEAT
1
4
7
2
5
8
0
3
6
9
A-B
ANGLE
DVD PROG.
96kHz 24bit
V.S.S.
U
V
N
O
SET UP CANCEL
A B C
D
E F
S10
Player
Page
A A DVD is loaded.
B It is possible to change the angle. [DVD]
C Illuminates during program play. [VCD] [CD]
D Title/chapter number [DVD]
1 Standby/On button (STANDBY/ON) . . . . . . . . . . . . . . . . . . 14
Press to switch the unit from on to standby mode or vice versa.
In standby mode, the unit is still consuming a small amount of
power.
2 Disc tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3 Disc tray open/close button (<OPEN/CLOSE) . . . . . . . . . 14
4 Play button (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Pause button (;) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6 Stop button (º) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7 FL display
Track number [VCD] [CD]
E Linear PCM of 96 kHz sampling is being played.
F Linear PCM of 24 bit is being played.
Remote control
Page
8 Virtual Surround Sound indicator (V.S.S.) . . . . . . . . . . . . . 21
9 Skip button (: SKIP 9) . . . . . . . . . . . . . . . . . . . . . . . . 16
: Search button (6 SEARCH 5) . . . . . . . . . . . . . . . . . . . 17
G Top menu button (TOP MENU) . . . . . . . . . . . . . . . . . . . . . . 14
H Cursor buttons (3, 4, 2, 1)/Enter button (ENTER) . . . . 14
I On screen button (ON SCREEN) . . . . . . . . . . . . . . . . . . . . . 25
J Play mode button (PLAY MODE) . . . . . . . . . . . . . . . . . . . . . 23
K Subtitle button (SUBTITLE) . . . . . . . . . . . . . . . . . . . . . . . . . 20
L Repeat button (REPEAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
M A-B repeat button (A-B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
N Virtual Surround Sound button (V.S.S.) . . . . . . . . . . . . . . . 21
O Setup button (SET UP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
P Slow/Search buttons (6, 5 SLOW/SEARCH) . . . . . . . 17
Q Menu button (MENU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
R Return button (RETURN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
S Angle button (ANGLE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
T Audio button (AUDIO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
U Numeric buttons (1–9, 0, S10) . . . . . . . . . . . . . . . . . . . . . . . 14
³To select a 2-digit number
;
Rotates during play.
Rotates fast clockwise or counterclockwise during
rapid advance (reverse).
Rotates slowly clockwise or counterclockwise
during slow-motion play. [DVD] [VCD]
Illuminates in the stop mode.
< Illuminates during playback.
Flashes when the RESUME function is ON.
= Illuminates during repeat play.
> Illuminates in the still picture (pause) mode.
? Elapsed playing time from the start of the title/track during
play
@ Audio channel information recorded in the disc being
played back (e.g. 2ch or 5.1ch)
Example: To select track 23
Press [S10], then [2] and [3].
V Cancel button (CANCEL) . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Center
Rear (left)
Main (left)
Rear (right)
Subwoofer
Main (right)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Home theater
º Settings for your Home Theater
Set up
Settings in
“7 Digital Audio Output”
Equipment to be connected
Speakers
³Main L/R
³Center¤2
³Rear L/R¤2
³Subwoofer¤2
Page
System
To enjoy 5.1 channel
surround sound
AV amplifier with digital input and
built-in Dolby Digital/DTS decoder
1. PCM down Conversion⇒“Yes”
2. Dolby Digital⇒“Bitstream”
3. DTS⇒“Bitstream”
9
AV amplifier with digital input and
built-in Dolby Digital decoder
(without DTS decoder)
³Main L/R
³Center¤2
³Rear L/R¤2
³Subwoofer¤2
1. PCM down Conversion⇒“Yes”
2. Dolby Digital⇒“Bitstream”
3. DTS⇒“Off”
9
To enjoy Dolby surround
sound¤1
AV amplifier with built-in Dolby
Pro Logic decoder
³Main L/R
³Center
³Rear L/R
1. PCM down Conversion⇒“Yes”
2. Dolby Digital⇒“PCM”
3. DTS⇒“Off”
GnigSarted
10
11
11
To enjoy linear PCM sound
Stereo amplifier with digital input
and built-in high sampling DA
converter rated at 96 kHz
Main L/R
Main L/R
1. PCM down Conversion⇒“No”
2. Dolby Digital⇒“PCM”
3. DTS⇒“Off”
Stereo amplifier with digital input
and built-in conventional DA
converter
1. PCM down Conversion⇒“Yes”
2. Dolby Digital⇒“PCM”
3. DTS⇒“Off”
¤1 If you have connected an AV amplifier with built-in Dolby Pro Logic decoder, you may need to connect center and rear speakers.
¤2 Connect speakers if necessary and make the speaker settings on the amplifier.
º Upgrading your television
³You can connect CRT projectors, LCD projectors, and projection televisions.
³See “Connection to a television” (á pages 12 and 13) for details on connection.
Note
³The equipment connections described are examples.
³Peripheral equipment and optional cables sold separately unless otherwise indicated.
º Before connections
³Ensure that this player and other equipment to be connected are switched to the standby mode or off and disconnect the AC power supply cord
before commencing connection.
³Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely.
³Read through the instructions before connecting other equipment.
³Ensure that you observe the color coding when connecting audio and video cables.
Note
³TV volume may be lower when playing DVDs than during television broadcasts. Turn the volume up while playing DVDs and reduce it to the
previous level before switching the source back to television to avoid sudden changes in volume.
³When you have finished connection, select the appropriate screen type at the initial setting “6 TV Aspect” according to your television (4:3/16:9)
(á page 31). No changes are needed if you connect the player to a conventional television (4:3).
Conserving power
³The unit consumes approx. 2.0 W even when it is turned off with [STANDBY/ON]. To save power when the unit is not to be used for a long time,
unplug it from the household AC outlet.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an AV amplifier with a built-in decoder
You can enjoy the 5.1-channel surround sound found on DVD recorded with Dolby Digital or DTS Digital Surround by connecting an AV amplifier
with a built-in decoder or a separate decoder-amplifier combination.
Note when connecting the optical fiber cable
AC 120 V, 60 Hz
To household
AC outlet
Align the plug with the
terminal
Dust protection cap
AC power supply
³Remove the dust protection cap from the optical digital audio
output terminal and connect the cable firmly so that the
configurations of both the cable and the terminal match.
³Keep the dust protection cap and reattach when not using the
terminal.
cord (included)
GingSarted
Back of the player
COMPONENT VIDEO
AUDIO OUT
VIDEO OUT
AC IN
PCM/Î DIGITAL
DTS
PR
L
VIDEO
S
VIDEO
OPTICAL
PB
Y
R
SUBWOOFER
Optical fiber cable
³Do not bend the optical fiber cable when connecting it.
AV amplifier with a built-in decoder
³Read the instructions for the amplifier and speakers for connection
details.
OPTICAL
Speaker
You can connect from 3 to 5 speakers including the main two.
³Main speaker (L/R)
³Center speaker
³Rear speaker (L/R)
³Subwoofer
When you have finished connection
Adjust each item of “7 Digital Audio Output” to suit your decoder (á page 33).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Home theater
Connecting audio equipment with 2-channel analog audio input terminals
You can enjoy stereo sound if you connect an amplifier, system component or TV that has 2-channel analog audio input terminals. By connecting a
subwoofer, you can also enjoy powerful bass.
º Connecting the amplifier, system component or TV
Amplifier and speakers or system component
³Read the instructions for the amplifier and speakers or
system component for connection details.
AV amplifier with built-in Dolby Pro Logic
decoder
Television
³If you connect an AV amplifier with built-in
Dolby Pro Logic decoder, you will also need to
connect center and rear speakers to enjoy
surround sound. Read the instructions for the
equipment for connection details.
GnigSarted
³Turn off V.S.S. (á page 21) and subwoofer
output (á item g on page 27). Dolby Pro Logic
will not function correctly if they are on.
AUDIO
IN
L
SUB
WOOFER
AUX IN
or
L
R
R
Audio cable
INPUT
Active subwoofer
³Place the subwoofer as close as possible
to the front center.
Audio cable
Back of the player
COMPONENT VIDEO
AUDIO OUT
VIDEO OUT
PCM/Î DIGITAL
DTS
PR
L
VIDEO
S
VIDEO
OPTICAL
PB
Y
R
SUBWOOFER
º If connecting
audio equipment
which has no
subwoofer output
terminal
Audio cable
Active subwoofer
³Use the On-Screen Menu Icons to turn
subwoofer output on (á item g on
page 27).
INPUT
³Adjust the volume of the subwoofer to suit
your preference.
When you have finished connection
Adjust each item of “7 Digital Audio Output” (á page 33).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting audio equipment with digital audio input terminals
Note when connecting the optical fiber cable
Back of the player
Align the plug with
the terminal
Dust protection cap
AUDIO OUT
VID
PCM/Î DIGITAL
DTS
VIDEO
S
VIDEO
³Remove the dust protection cap from the optical digital audio
output terminal and connect the cable firmly so that the
configurations of both the cable and the terminal match.
³Keep the dust protection cap and reattach when not using the
terminal.
OPTICAL
R
SUBWOOFER
GingSarted
Optical fiber cable
³Do not bend the optical fiber cable when connecting it.
OPTICAL
System component or amplifier with digital audio input
terminals and speakers
³Read the instructions for the amplifier and speakers or system
component for connection details.
When you have finished connection
Adjust each item of “7 Digital Audio Output” (á page 33).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to a television
Connect Your Player Directly To Your
Do not place the
player on amplifiers or
other equipment
which may become
Television.
If the player is connected to the television through a video cas-
sette recorder, the picture may not be played back correctly due
to the copy guard. So we strongly recommend you do not con-
nect the player to your video cassette recorder when setting up
your home entertainment system.
hot.
The heat can damage the player.
³Connect to the television section if you connect the player to a
combined television-video player.
Connecting to a television with video input terminal
GnigSarted
AUDIO VIDEO
IN
IN
L
R
Television
Audio/video cable (included)
AUDIO OUT
VIDEO OUT
PCM/Î DIGITAL
DTS
L
VIDEO
S
VIDEO
OPTICAL
R
SUBWOOFER
Back of the player
Connecting to a television with S video input terminal
AUDIO
IN
S VIDEO
IN
L
R
Television
Audio/video cable (included)
S video cable
S video output terminal
The S (separate) video output terminal achieves a clearer
picture than the video output terminal by separating the color (C)
and luminance (Y) signals before transmitting them to the
television. (Actual results depend on the television.)
AUDIO OUT
VIDEO OUT
PCM/Î DIGITAL
DTS
L
VIDEO
S
VIDEO
OPTICAL
R
SUBWOOFER
Back of the player
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a television with component video input terminals
AUDIO
IN
COMPONENT
VIDEO IN
L
Y PB PR
R
Television
GingSarted
Audio/video cable (included)
Video cable
Component video output terminals (Y/PB/PR)
The component video output terminals output the color
difference signals (PB/PR) and luminance signal (Y)
separately in order to achieve high fidelity in
reproducing colors.
COMPONENT VIDEO
PR
AUDIO OUT
VIDEO OUT
PCM/Î DIGITAL
DTS
L
VIDEO
S
VIDEO
OPTICAL
³The description of the component video input
terminals depends on the television or monitor
(e.g. Y/PB/PR, Y/B-Y/R-Y, Y/CB/CR and so on).
Connect to terminals of the same color.
PB
Y
R
SUBWOOFER
Back of the player
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic play
1
3
2 4
º Before enjoying DVD/Video CD/CD
The menu language for this player has been set to English, but you
can change the language to French or Spanish (á “3 Menu Lan-
guage”, page 31). English has been used in the examples shown.
NATURAL SOUND DVD PLAYER
STANDBY/ON
f
OPEN/CLOSE
DVD
/
VIDEO CD / CD
:
SKIP
;
C
SEARCH
D
D
I
G
I
T
A
L
V.S.S.
Preparations
:
SKIP
;
³Ensure connections to your television and audio equipment are
correct.
POWER
OPEN/CLOSE
H/I
1
2
4
³Turn on your television and other equipment.
³Switch the video input mode on the television to suit the type of
connection you have made (e.g., VCR 2).
STOP
∫
PAUSE
;
PLAY
1
SLOW/
SEARCH
SKIP
9
:
6
5
:, 9SKIP
TOP MENU
ON SCREEN
MENU
MENU
1 Press [STANDBY/ON] to switch on the
power.
TOP MENU
ENTER
Cursor
buttons/
ENTER
RETURN
2 Press [< OPEN/CLOSE] to open the
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
disc tray.
REPEAT
1
4
7
2
5
8
0
3
6
9
A-B
3 Place the disc on the disc tray.
Numeric
buttons
V.S.S.
³Insert inside the guides.
³Do not load more than one disc.
SET UP CANCEL
S10
4 Press [1].
The disc tray is automatically closed and play begins.
BcOperations
1
STANDBY/ON
When a menu screen appears on the
TV monitor
A
»
Press the cursor buttons [3, 4, 2, 1]
and press [ENTER], or press the numeric
buttons, to select the item.
Play of the selected item now begins.
³The cursor buttons are not effective for selecting items for Video
CDs.
2
Open
f
OPEN/CLOSE
º Other buttons used to operate menus
Label must face upward.
(With double-sided discs, load
so the label for the side you
want to play is facing up.)
3
Read the disc’s instructions for further details about operation.
[9 SKIP]: Shows the next menu.
[: SKIP]: Shows the previous menu.
[RETURN]: Shows the menu screen.
[TOP MENU]: Shows the first menu screen. [DVD]
[MENU]: Shows the menu screen. [DVD]
Note
³“NO PLAY” is displayed on the FL display if you load the following
kinds of discs and they cannot be played:
5q (12 cm) disc
3q (8 cm) disc
³
DVD for which playback is prohibited by the initial settings
“2 Ratings” (á page 30).
DVD with a region number other than “1” or “ALL” (á page 6).
³
³
If the disc is put in upside down (and it is a single sided disc).
4
Close
Reading
³When “$” appears on the TV monitor when a button is pressed, the
operation is prohibited by the player or disc.
A
ENTER
1
2
5
8
0
3
6
9
4
7
S10
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic play
1
∫
STANDBY/ON
NATURAL SOUND DVD PLAYER
A
»
Stopping play
STANDBY/ON
f OPEN/CLOSE
DVD
/
VIDEO CD / CD
:
SKIP
;
C
SEARCH
D
Press [º] during play.
D
I
G
I
T
A
L
V.S.S.
³The player records the point where [º] was pressed during play.
(“!” flashes on the player’s FL display.)
POWER
OPEN/CLOSE
To resume play from where you stopped it
(RESUME function)
H/I
B
»
POWERH/I
∫
STOP
∫
PAUSE
;
PLAY
1
1
STOP
PLAY
SLOW/
SKIP
:
SEARCH
Press [1] while “!” is flashing on the FL display.
Play will resume from the point where [º] was pressed.
9
6
5
TOP MENU
MENU
To clear the RESUME function
Press [º] again or open the disc tray while “!” is flashing on the FL
display.
A
B
Note
³The RESUME function works only with titles for which the elapsed
playing time appears on the player’s FL display during playback.
³This feature remains active if the player is switched to the standby
mode and then turned back ON.
BcOperations
Chapter preview function
C
»
[DVD]
This function plays the first few seconds of each chapter from the
beginning of the title up to the point where operation was stopped.
This makes it possible to review previous chapters.
1. Press [1] while “!” is flashing on the FL display.
(The message illustrated is briefly displayed.)
2. Press [1] again while the message is displayed on the
screen.
C
1·2
NATURAL SOUND DVD PLAYER
STANDBY/ON
f OPEN/CLOSE
DVD
/
VIDEO CD / CD
:
SKIP
;
C
SEARCH
D
Normal playback will commence from the point where operation was
stopped.
D
I
G
I
T
A
L
V.S.S.
Note
³Canceling the RESUME function will also clear the chapter preview
function.
POWER
OPEN/CLOSE
H/I
³The chapter preview function may not work with some DVDs.
STOP
∫
PAUSE
;
PLAY
1
1·2
SLOW/
SEARCH
SKIP
:
9
6
5
º After operation
TOP MENU
MENU
When the player is not in use, remove the disc and press
[STANDBY/ON] to switch the player to the standby mode.
The player is automatically switched to the standby mode after
30 minutes or so have elapsed in the stop mode.
(Auto power-off function)
1
2
Note
³The disc continues to rotate while the menu is displayed even after
the player has finished playing a particular item. Stop the player
when you finish viewing to preserve the player’s motor and prevent
screen burn.
Press PLAY to Chapter Preview
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Other methods of play
1 ;
NATURAL SOUND DVD PLAYER
Features on the next few pages are accessed mainly by using the
remote control.
STANDBY/ON
f
OPEN/CLOSE
DVD
/
VIDEO CD / CD
:
SKIP
;
C
SEARCH
D
D
I
G
I
T
A
L
V.S.S.
A
Still picture (Pause)
»
:
SKIP
;
Press [; PAUSE] during play.
POWER
H/I
PAUSE
OPEN/CLOSE
STOP
PLAY
1
To return to normal play
Press [1 PLAY].
∫
;
;
1
PAUSE
PLAY
SLOW/
SEARCH
SKIP
:
9
6
5
:, 9SKIP
TOP MENU
MENU
B
Skipping chapters or tracks
»
ENTER
Cursor
buttons
Press [:, 9 SKIP] or [: SKIP
9], during play or while paused.
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
REPEAT
1
4
7
2
5
8
0
3
6
9
Play position
A-B
twice
once
once
twice
V.S.S.
SET UP CANCEL
Chapter/track Chapter/track Chapter/track
S10
[
]
[
]
:
9
BcOperations
For your reference
³When [:, 9 SKIP] or [: SKIP 9] on the player is
pressed during menu play of Video CDs with playback control, a
menu screen may sometimes be recalled.
A
C
Frame advance (Frame reverse)
»
PAUSE
;
[DVD] [VCD]
Press the cursor buttons [2, 1] while
paused.
³The disc is advanced (reversed) by one frame each time the cursor
buttons [2, 1] are pressed.
³When the cursor buttons [2, 1] are kept pressed, consecutive
frame advance (reverse) works.
B
C
SKIP
:
9
To return to normal play
Press [1 PLAY].
Reverse Forward
For your reference
³Pressing [; PAUSE] also activates frame advance.
³Whether the pictures are advanced by a “Frame” or “Field” is
automatic, but you can change the initial settings to choose how the
picture is advanced (á page 34).
Reverse
(DVD only)
Forward
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Other methods of play
1
NATURAL SOUND DVD PLAYER
A
»
Slow-motion play
STANDBY/ON
f
OPEN/CLOSE
DVD
/
VIDEO CD / CD
:
SKIP
;
C
SEARCH
D
D
I
G
I
T
A
L
V.S.S.
[DVD] [VCD]
Press [6, 5 SLOW/SEARCH] or
C
SEARCH
D
[6 SEARCH 5] while paused (á page 16).
POWER
OPEN/CLOSE
³Each press increases the speed of slow-motion.
H/I
STOP
∫
PAUSE
;
PLAY
1
1PLAY
SLOW/
SEARCH
SKIP
:
9
6
5
6, 5
SLOW/SEARCH
³There are five speeds of slow-motion.
TOP MENU
MENU
To return to normal play
ENTER
Press [1 PLAY].
For your reference
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
³When [6, 5 SLOW/SEARCH] or [6 SEARCH 5] on the
player is pressed during menu play of Video CDs with playback
control, a menu screen may sometimes be recalled.
REPEAT
1
4
7
2
5
8
0
3
6
9
A-B
V.S.S.
SET UP CANCEL
B
Rapid advance (Rapid reverse)
»
S10
Press [6, 5 SLOW/SEARCH] or
A
B
BcOperations
[6 SEARCH 5] during play.
³Each press increases the speed of the search.
SLOW/
SEARCH
6
5
³There are five speeds of advance (reverse).
To return to normal play
Press [1 PLAY].
Reverse
Forward
(DVD only)
For your reference
³When [6, 5 SLOW/SEARCH] or [6 SEARCH 5] on the
player is pressed during menu play of Video CDs with playback
control, a menu screen may sometimes be recalled.
³For DVDs and Video CDs, audio will be heard during searching (for-
ward direction only) at the initial search speed. (To turn audio off,
á “2 Audio during Search”, on page 34.)
SLOW/
SEARCH
6
5
Reverse Forward
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Other methods of play
POWER
H/I
OPEN/CLOSE
STOP
∫
PAUSE
;
PLAY
1
A
»
[VCD]
Canceling playback control
1
1
SLOW/
SEARCH
SKIP
:
9
6
5
TOP MENU
MENU
1
2
1 Press [º STOP] after the menu screen
ENTER
appears (after step 4 on page 14).
“PBC” will be cleared from the player’s FL display.
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
2 Press the numeric buttons to select a
REPEAT
1
4
7
2
5
8
0
3
6
9
track (á item U on page 7 for number entry).
Play begins.
A-B
2
V.S.S.
³Refer to the jacket etc. of the disc concerned for the track
numbers.
³Press [1] to start play from the beginning of the disc.
SET UP CANCEL
S10
To return to menu play
Press [º STOP] to stop play, press [MENU], and press the numeric
buttons to select an item.
“PBC” lights on the player’s FL display.
A
B
Using menus to play
»
[DVD]
BcOperations
STOP
∫
1
By calling up menus during play, you can start play from a specific
title or chapter, or change the soundtrack and subtitle languages.
1 Press [TOP MENU] or [MENU] during
play to display the menu.
2
³Press again to return to what you were watching.
1
4
7
2
3
6
9
5
8
0
2 Press the cursor buttons [3, 4, 2,
1] to select an item and press
S10
[ENTER].
The selected item is confirmed.
³Repeat if other menus are shown.
B
TOP MENU
MENU
1
DVDs can have several menus. The menu displayed when you press
[TOP MENU] may be different to the menu displayed when you press
[MENU]. [C]
For your reference
³Menu content depends on the disc. These operating instructions
describe the basic steps.
³Both buttons take you to the same menu if the disc has only one
menu.
2
ENTER
Example: if you press the buttons while you are playing title 2
C
Title 1
Title 2
Title 3
The disc’s top
menu
Menu
Menu
Menu
MENU
TOP MENU
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced operations
TOP MENU
ON SCREEN
MENU
A
ENTER
Cursor
buttons/
ENTER
A
»
[DVD]
Changing soundtrack
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
AUDIO
REPEAT
Some DVDs have more than one soundtrack recorded on them, and
you can change soundtrack during play.
1
4
7
2
5
8
0
3
6
9
A-B
Numeric
buttons
V.S.S.
Press [AUDIO] during play to display the
SET UP CANCEL
S10
current soundtrack.
The number changes each time you press the button.
³You can also use the cursor buttons [3, 4], or the numeric buttons
to change the soundtrack.
AUDIO
To clear the display
Press [ENTER].
Î Digital
ENG 3/2.1ch
Soundtrack being
played back
1
(“–” indicates a soundtrack
is not recorded.)
For your reference
³You can only select languages or sound formats if they have been
recorded on the disc you are playing.
Hello
³If resume (á page 15) is canceled or if you stop play of an interac-
tive DVD, the soundtrack revert to the initial settings. (á page 29)
³Some discs allow changes to soundtrack only by using the disc’s
menus.
Î Digital
FRA 3/2.1ch
2
Switching vocals ON or OFF for Karaoke
discs
B
»
Bonjour
[DVD] [VCD]
1. Press [AUDIO] during play.
2. Press the cursor buttons [3, 4, 2, 1] or press [AUDIO] to
change the setting.
AvcdOperations
DVD Karaoke [2, 1]
³Solo
–––: Vocal OFF
B
TOP MENU
MENU
³Duet
–––: Vocal OFF
1r2: Vocal 1, 2 ON
ENTER
ON: Vocal ON
2·ENTER
V1:
V2:
Vocal 1 only ON
Vocal 2 only ON
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
³Choose “–––” for Karaoke.
³Choose “V1” or “V2” to duet with the player.
1
REPEAT
1
2
3
Video CD ([3, 4] or [AUDIO])
LR: Vocals (Vocals seem to come from the right)
L:
R:
No Vocals
1
2
AUDIO
Vocals (Vocals seem to come from both left and right)
³Choose “L” for Karaoke.
To clear the display
Press [ENTER].
For your reference
DVD
³Karaoke discs may show a menu after each track. Some will have a
menu that allows you to play all the tracks.
³Some discs require different operations to those described. Read
the disc’s instructions for details.
Vocal
ON
1
U
Video CD
AUDIO
L R
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced operations
TOP MENU
ON SCREEN
MENU
A
ENTER
Cursor
buttons/
ENTER
A
»
[DVD]
Changing subtitle language
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
SUBTITLE
REPEAT
Some DVDs have more than one subtitle language recorded on
them, and you can change subtitle language during play.
1
4
7
2
5
8
0
3
6
9
A-B
Numeric
buttons
V.S.S.
Press [SUBTITLE] during play to display
SET UP CANCEL
S10
the current language number.
The number changes each time you press the button.
³You can also use the cursor buttons [3, 4] or the numeric buttons
to change the language number.
SUBTITLE
Subtitle language number being played back
(“––” indicates subtitles are not recorded)
To clear the display
Press [ENTER].
ON
ON
1
ENG
2
FRA
To clear/display the subtitles
B
»
1. Press [SUBTITLE].
2. Press the cursor buttons [2, 1] to select “ON” or “OFF”.
I love you
Je t’aime
Note
³In some cases, the subtitle language is not changed to the selected
one immediately.
³When a disc supporting closed captions is played, the subtitles and
closed captions may overlap each other on the TV monitor. In this
case, turn the subtitles off.
B
TOP MENU
ON SCREEN
MENU
ENTER
2
1
For your reference
³You can only select languages if they have been recorded on the
disc you are playing.
³If resume (á page 15) is canceled or if you stop play of an interac-
tive DVD, the subtitle languages revert to the initial settings
(á page 29).
³Some discs allow changes to subtitle languages only by using the
disc’s menus.
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
REPEAT
1
2
3
AcvdOperations
SUBTITLE
1
2
C
»
[DVD]
Viewing from another angle
Some DVDs allow you to view the same scene from different angles.
“ANGLE” lights on the FL display to indicate that the feature is
available.
Press [ANGLE] during play to display the
TOP MENU
ON SCREEN
MENU
C
current angle number.
The number changes each time you press the button.
³You can also use the cursor buttons [3, 4] or the numeric buttons
to change the angle.
ENTER
Cursor
buttons/
ENTER
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
ANGLE
REPEAT
1
4
7
2
5
8
0
3
6
9
A-B
To clear the display
Press [ENTER].
Numeric
buttons
V.S.S.
SET UP CANCEL
For your reference
S10
³You can only select angles if they have been recorded on the disc
you are playing.
ANGLE
³Some discs allow you to set angles before multi-angle scenes are
played.
³Some discs allow changes to angles only by using the disc’s
menus.
Angle number being played back
1
3
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced operations
V.S.S. indicator
NATURAL SOUND DVD PLAYER
Reproducing an Advanced Virtual
Surround Sound (V.S.S.) effect
STANDBY/ON
f
OPEN/CLOSE
A
»
DVD
/
VIDEO CD / CD
:
SKIP
;
C
SEARCH
D
D
I
G
I
T
A
L
V.S.S.
[DVD] (Dolby Digital, 2-channel or over only)
Use this feature to enjoy a surround-like effect if you are using two
main speakers.
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
REPEAT
Press [V.S.S.] during play.
Each time this button is pressed, the player’s FL display changes:
a V.S.S. 1 (Natural effect)
b V.S.S. 2 (Emphasized effect)
c V.S.S. is canceled
1
4
7
2
5
8
0
3
6
9
A-B
V.S.S.
V.S.S.
SET UP CANCEL
S10
³The V.S.S. indicator lights up green when the V.S.S. function is ac-
tivated.
A
B
V.S.S.
Note
a
D
V D
³V.S.S. effect does not work with Karaoke DVDs.
³V.S.S. will not work or will have less effect with some discs.
³Turn off the TV surround sound and other surround sound effects
when using this effect.
b
D
V D
³Sound will only come from the two main speakers if V.S.S. is on.
For your reference [B]
c
³For optimum effect, it is recommended that the distance between
the television and the listening position be about 3 to 4 times the
distance between the right and left main speakers.
³You can also change the V.S.S. level with the On-screen Menu
Icons [á “f Virtual Surround Sound (V.S.S.)”, page 27].
D
V D
A
³V.S.S. effects
Speaker
Speaker
AvcdOperations
V.S.S. 1
V.S.S. 2
3 to 4 times distance A
Stereo discs
The main speakers
sound further apart.
The surround-like
effect in V.S.S. 1 is
increased.
Surround signal
recorded discs
Surround sound
seems to come
from the side.
Listening position
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced operations
TOP MENU
ON SCREEN
MENU
ENTER
A
»
Repeat play
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
Press [REPEAT] during play.
Each time this button is pressed, the TV monitor changes as illustrat-
ed and the disc will repeat a chapter or title (DVD) or a track (Video
CD/CD).
Repeat play starts when the display changes.
³DVD
REPEAT
1
4
7
2
5
8
0
3
6
9
REPEAT
A-B
V.S.S.
SET UP CANCEL
S10
a Normal play
b Repeat of chapter being played
c Repeat of title being played
d Cancel repeat mode (Normal play)
A
REPEAT
³Video CD/CD
e Normal play
f Repeat of track being played
g Repeat of entire disc contents
h Cancel repeat mode (Normal play)
a
e
b
c
d
f
g
h
T
C
T
To return to normal play
Press [REPEAT] until “1 OFF” is displayed.
A
Note
³Repeat play may not work correctly with some DVDs.
³Repeat play does not work with an interactive DVD or during menu
play of a Video CD with playback control.
³There is no mode for repeating the whole DVD.
OFF
OFF
B
To enjoy program repeat play
B
REPEAT
»
[VCD] [CD]
i
j
k
l
AcvdOperations
If [REPEAT] is pressed during program play (á page 23), the display
changes as illustrated.
i Program play
j Repeat of track being played
k Repeat of all programmed tracks
l Cancel repeat mode (Program play)
T
PRG
PRG
A
OFF PRG
To return to program play
Press [REPEAT] until “1 OFF” is displayed.
TOP MENU
MENU
C
Repeating sections between two
specific points (A-B repeat)
C
»
ENTER
1 Press [A-B] during play at the point
where repeat play is to start (A).
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
REPEAT
1
4
7
2
5
8
0
3
6
9
A-B
2 Press [A-B] at the point where repeat
1·2
V.S.S.
play is to be concluded (B).
SET UP CANCEL
Repeat play of the section between points A and B starts.
S10
1
2
A-B
To return to normal play
Press [A-B] until “1 &” is displayed.
A
Note
³A-B repeat play does not work with an interactive DVD.
³Some subtitles recorded around point A or B may fail to appear
(DVD).
³A-B repeat play works only within a title (DVD) or a track (Video CD/
CD).
A-B
AB
For your reference
³The end of a track or title is automatically determined as point B.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced operations
POWER
H/I
OPEN/CLOSE
STOP
∫
PAUSE
;
PLAY
1
Program play
∫STOP
3
SLOW/
SEARCH
SKIP
:
9
6
5
6
,
5SLOW/SEARCH
[VCD] [CD]
The player plays the tracks on the disc in the order you specify. Up to
TOP MENU
MENU
32 tracks can be programmed.
If you enter over 32 tracks, the last programmed track is replaced
with the new one.
ENTER
Cursor
buttons/
ENTER
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
1 Press [PLAY MODE] while stopped
REPEAT
1
4
7
2
5
8
0
3
6
9
until the illustrated screen appears.
³If “/” appears on the television, press [º STOP] to cancel
the RESUME function, then press [PLAY MODE].
A-B
1
2
V.S.S.
SET UP CANCEL
S10
CANCEL
2 Press the numeric buttons to select
the track (á item U on page 7 for number entry).
The selected track is stored in memory.
³If you press [ENTER], you can use the cursor buttons [3, 4]
to select a track. Press [ENTER] to register the track
number.
Choose a track, then press ENTER.
Track Time
1
Clear
PLAY MODE
1
2
³Repeat step 2 to select another track.
3
4
Clear all
5
6
7
8
Total time
3 Press [1 PLAY].
Play now begins in the programmed sequence.
Press PLAY to start
To exit the screen
Press [PLAY MODE] twice.
FL display (e.g. CD)
To add tracks
PROG.
1. Press [º STOP] twice during program play to show the program
play screen.
Flashes
2. Select the available item with the cursor buttons [3, 4], then
repeat step 2.
AvcdOperations
³Press [6, 5 SLOW/SEARCH] to turn the pages of the program
to make selection quicker.
To return to normal play
1. Press [º STOP] twice during program play.
(Program play is suspended.)
2. Press [PLAY MODE] twice.
Choose a track, then press ENTER.
2
3
Track Time
1
4
7
2
5
8
0
3
6
9
Clear
1
2
3
4
5
6
7
8
5
2:02
Clear all
Total time
2:02
3. Press [1 PLAY].
S10
³The program is retained in memory.
Operation by observing the unit’s FL display
³Use the numeric buttons to enter track numbers.
³To check the program, press the cursor buttons [3, 4].
Press PLAY to start
PROG.
Track No.
Program No.
Clearing the program
When the program play screen is displayed
³To clear the programmed tracks one by one
Select the track, move to “Clear” with the cursor buttons and press
[ENTER].
(Selecting the track and pressing [CANCEL] also clears the pro-
grammed track.)
PLAY
1
³To clear the whole program
Move to “Clear all” with the cursor buttons and press [ENTER].
(The program is also cleared when the player is switched to the
standby mode or turned off, or the disc tray is opened.)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced operations
POWER
H/I
OPEN/CLOSE
STOP
∫
PAUSE
;
PLAY
1
Random play
∫STOP
2
SLOW/
SEARCH
SKIP
:
9
6
5
[VCD] [CD]
The player plays the tracks on the disc in random order.
TOP MENU
MENU
ENTER
1 Press [PLAY MODE] while stopped
until the illustrated screen appears.
³If “/” appears on the television, press [º STOP] to cancel
the RESUME function, then press [PLAY MODE].
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
REPEAT
1
4
7
2
5
8
0
3
6
9
A-B
1
2 Press [1 PLAY].
V.S.S.
Play now begins in random order.
SET UP CANCEL
S10
To exit the screen
Press [PLAY MODE] once.
To return to normal play
1. Press [º STOP] twice during random play.
(Random play is suspended.)
2. Press [PLAY MODE] once.
3. Press [1 PLAY].
1
2
PLAY MODE
Random Playback
Press PLAY to start
PLAY
1
AcvdOperations
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using On-Screen Menu Icons
DVD
A
Î Digital
ENG 3/2.1ch
ON
1
30
1:06:37
1
1
1
ENG
On-Screen Menu Icons
On-Screen Menu Icons are long thin menus that contain information
about the disc or player. These menus allow you to perform opera-
tions by changing this information.
OFF
OFF
N
OFF
ON
*****
p100
µ100
Examples of On-Screen Menu Icons [A]
The screens depend on the disc contents.
B
»
Common procedures
Video CD
PBCOFF
1 Press [ON SCREEN] during play or in
1
3:37
PRG
L R
the stop mode.
Each time this button is pressed, the TV monitor changes as
shown below.
N
ON
OFF
*****
[>On-Screen Menu Icons for disc information
l
l
l
l
l
;
p
40
µ
40
On-Screen Menu Icons for player information
;
Shuttle screen
;
{= On-Screen Menu Icons cleared
³Some functions cannot be accessed from the stop mode.
CD
1
3:37
PRG
2 Press the cursor buttons [2, 1] to se-
lect the item.
The item is highlighted in yellow.
ON
OFF
*****
3 Press the cursor buttons [3, 4] to se-
p50
µ50
lect the setting.
³For some functions, the setting will be registered immediate-
ly; for others, [ENTER] or [1 PLAY] must be pressed.
³When numbers are displayed (e.g. title No.), the numeric
buttons are also effective for setting instead of the cursor
buttons [3, 4]. When numbers are entered with numeric
buttons, press [ENTER] to register the setting.
AvcdOperations
STOP
∫
PAUSE
;
PLAY
1
1PLAY
B
SLOW/
SKIP
SEARCH
:
9
6
5
TOP MENU
MENU
To clear the On-Screen Menu Icons
Press [RETURN] or [CANCEL].
ENTER
2·3
1
For your reference
RETURN
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
³The On-Screen Menu Icons may not be displayed when playing
some kinds of DVD software, or if the television’s automatic picture
zoom function is on. Change the position of the On-Screen Menu
Icons in “4 On-Screen Messages” if this occurs (á page 31).
³The color (blue, violet or green) of the On-Screen Menu Icons can
be changed (á page 31).
REPEAT
1
4
7
2
5
8
0
3
6
9
A-B
Numeric
buttons
V.S.S.
SET UP CANCEL
S10
CANCEL
³“# $” around the icon means that the item can be changed using
the cursor buttons [3, 4].
1
2
ON SCREEN
2
3
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using On-Screen Menu Icons
Detailed descriptions of each icon
Screen for disc information
º DVD
a
b
c
de
f
g h i j
Î Digital
ENG 3/2.1ch
ON
1
30
1:06:37
1
1
1
ENG
a Title No.
f Audio attribute
Change the No. with the cursor buttons [3, 4] or the numeric
Shows the audio attributes of the selected soundtrack.
buttons and press [ENTER].
LPCM/ë Digital/DTS: Signal type
b Chapter No.
k:
b:
ch:
Vocal:
Sampling frequency (kHz)
Number of bits (bit)
Number of channels¤
Vocals indication
Change the No. with the cursor buttons [3, 4] or the numeric
buttons and press [ENTER].
c Time
(hour:minute:second)
Enter the time from which you want to start play and press
³You can switch vocals ON or OFF with the cursor buttons
[3, 4].
[ENTER].
[DVD Karaoke (Solo)]: ––– (OFF) or ON
[DVD Karaoke (Duet)]: ––– (OFF), V1iV2, V1 or V2
g Subtitle language No.
Example: To specify “1 hour 6 min. 37 sec.”, enter “10637”.
d Soundtrack No.
Change the No. with the cursor buttons [3, 4] or the numeric
buttons.
Change the No. with the cursor buttons [3, 4] or the numeric
buttons.
e Soundtrack
h Subtitle on/off
Select “ON” or “OFF” with the cursor buttons [3, 4].
OFF: Subtitle is cleared.
ON: Subtitle is displayed.
ENG: English
FRA: French
DEU: German
ITA: Italian
ESP: Spanish
NLD: Dutch
SVE: Swedish
NOR: Norwegian
DAN: Danish
POR: Portuguese
RUS: Russian
JPN: Japanese
CHI: Chinese
KOR: Korean
MAL: Malay
VIE: Vietnamese
THA: Thai
i Subtitle language
See the table under item e.
j Angle No.
AcvdOperations
Change the No. with the cursor buttons [3, 4] or the numeric
buttons.
¢:
Others
º Video CD/CD
k
l
m
n
PBCOFF
L R
1
3:37
k Track No.
m Audio mode [VCD]
Change the No. with the cursor buttons [3, 4] or the numeric
buttons and press [ENTER].
l Time
Change the mode with the cursor buttons [3, 4].
LR: Left channel sound is output from the left speaker (L), and
right channel sound is output from the right speaker (R).
L: Left channel sound only is output from the speakers (L/R).
R: Right channel sound only is output from the speakers (L/R).
n Playback control [VCD]
(minute:second)
Display is changed each time the cursor buttons [3, 4] are
pressed. (The times cannot be changed.)
Elapsed playing time(------------)Remaining time of the track
^-------------)Remaining time of the disc(-------------J
Shows whether menu play is on or off (cannot be changed here).
OFF: Menu play is OFF.
ON: Menu play is ON.
Note
¤Example:
³The information actually displayed depends on the disc.
³During program and random play of Video CDs and CDs, the re-
maining time of the disc is not displayed.
3/2 .1ch
.1: Subwoofer signal (not displayed if there is no
subwoofer signal)
.0: No surround
.1: Mono surround
.2: Stereo surround (left/right)
.1: Center
.2: Main leftiMain right
.3: Main leftiMain rightiCenter
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen for player information
a
b
c
d
e
f
g
OFF
OFF
N
OFF
ON
*****
a A–B repeat play
d Marker (Marking parts you want to watch or listen to again)
Press [ENTER] during play and press [ENTER] again at the pre-
ferred point to store a marker. (Marker no. replaces “¢”.) (Up to
5 markers can be stored in the memory.)
To store the next marker, press the cursor button [1].
³To recall a marker
Press [ENTER] during play to store location A and press [ENTER]
again to store location B. Repeat play between the two locations
starts. Press [ENTER] again to return to normal play.
b Repeat play
Select the mode during play with the cursor buttons [3, 4].
[DVD]
OFF: Normal play
Select the marker no. with the cursor buttons [2, 1] and press
[ENTER].
C:
T:
Chapter repeat play
Title repeat play
³To clear a marker
Select the marker no. with the cursor buttons [2, 1] and press
[CANCEL].
[VCD] [CD]
OFF: Normal play
T:
³Some subtitles recorded around the marker may fail to appear.
³All the markers are cleared when the player is switched to the
standby mode or turned off, or the disc tray is opened.
e Cinema image
Track repeat play
Disc repeat play
A:
c Cinema dialogue
[DVD]
[DVD] [VCD]
Select the mode with the cursor buttons [3, 4] while a disc is
loaded.
OFF
___
Select the mode during play with the cursor buttons
[3, 4].
OFF: Normal volume
ON: Louder volume for dialogue
Play mode
[VCD] [CD] (á pages 23 and 24)
The current play mode is shown (cannot be
changed here).
N: Normal mode
C: Cinema mode (Cinema image): Picture for viewing movies
f Virtual Surround Sound (V.S.S.)
[DVD] (Dolby Digital, 2-channel or over only) (á page 21)
Select the level during play with the cursor buttons [3, 4].
OFF: V.S.S. off
AvcdOperations
PRG: Program play
RND: Random play
1:
2:
V.S.S. natural effect
V.S.S. emphasized effect
–––: Normal play
g Turning subwoofer output on and off (á page 10)
Select “ON” or “OFF” with the cursor buttons [3, 4].
ON: If you have connected a subwoofer
OFF: If you have not connected a subwoofer
Note
³A-B repeat play does not work with an interactive DVD.
³Repeat play and marker functions do not work with an interactive DVD or during menu play of a Video CD with playback control.
³Cinema dialogue is effective with Dolby Digital, three channels or over, where the dialogue is recorded in the center channel.
Shuttle screen
h
i
l
j
Maximum speed
DVD: j100
Video CD: j40
CD: j50
Maximum speed
DVD: i100
Video CD: i40
CD: i50
p
100
µ100
k
m
h Slow-motion play (Backward) [DVD]
Press the cursor buttons [3]>[2].
i Still/Pause
k Rapid reverse
Press the cursor buttons [4]>[2].
l Play
Press the cursor button [3].
j Slow-motion play (Forward) [DVD] [VCD]
Press the cursor buttons [3]>[1].
Press the cursor button [4].
m Rapid advance
Press the cursor buttons [4]>[1].
For your reference
³Each time the cursor buttons [2, 1] are pressed, the speed of rapid reverse/advance and slow-motion play increases up to 5 steps.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing initial settings
POWER
H/I
OPEN/CLOSE
Change the initial settings to suit your preference and to suit the play-
er to the environment in which it is being used.
STOP
∫
PAUSE
;
PLAY
1
SLOW/
SEARCH
SKIP
:
9
6
5
TOP MENU
MENU
Common procedures
ENTER
1 Press [SET UP] in the stop mode.
2·3
The initial settings screen is displayed.
RETURN
ON SCREEN
RETURN
PLAY MODE SUBTITLE AUDIO ANGLE
2 Press the cursor buttons [3, 4] to se-
REPEAT
1
4
7
2
5
8
0
3
6
9
lect the item and press [ENTER].
A-B
Each item that can be modified is displayed.
Numeric buttons
V.S.S.
1
Disc Languages (á page 29)
SET UP CANCEL
Change the soundtrack language, subtitle language and
the language used in the disc’s menu to be used for every
disc played back.
S10
1
2
Ratings (á page 30)
Change the ratings level to prevent play of discs, skip vio-
lent scenes, or replace scenes with others by entering a
password. This is also called a parental lock.
Menu Language (á page 31)
Change the language used for the on-screen displays and
initial settings menus.
3
4
On-Screen Messages (á page 31)
1
SET UP
Choose whether “Play”, “Still” and other displays will be
displayed or not, and the color and position of these dis-
plays as well as On-Screen Menu Icons.
FL Display (á page 31)
Change the brightness for the FL display.
TV Aspect (á page 31)
Change the settings to suit the type of television you have
connected.
Digital Audio Output (á page 32)
1 Disc Languages
2 Ratings
3 Menu Language
4 On-Screen Messages
5 FL Display
Level 8
English
5
6
Bright
4:3
6 TV Aspect
7 Digital Audio Output
9 Other Settings
7
9
Press RETURN to exit
Change the settings to suit the type of digital equipment
you have connected.
Other Settings (á page 34)
AcvdOperations
Choose the kind of picture shown when play is paused,
and various other settings to enhance your viewing expe-
rience.
2
3
3 Press the cursor buttons [3, 4] to se-
ENTER
ENTER
lect the setting and press [ENTER].
³Some items require additional steps.
(See the respective page.)
Setting is finished and the initial settings screen is displayed.
To cancel during setup operation
Press [RETURN]. (The previous screen is displayed.)
To exit the initial settings screen
Press [SET UP] or [RETURN].
Note
³There is no No. 8 in the initial settings menu of this player.
For your reference
³The numeric buttons can also be used instead of the cursor buttons
[3, 4] for selecting items or settings. Pressing [ENTER] is not
necessary.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Disc Languages
[DVD]
See page 28 for operation.
1
2
Audio
1
4
English (Factory preset)
Original
The original language of each disc will be selected.
Other ¢¢¢¢
Another language can be selected.¤
2
French
3
Spanish
Disc Languages
1
2
3
Audio
English
5
1
Subtitle
Menus
Automatic
English
Subtitle
Automatic (Factory preset)
Subtitle language will automatically be selected in accordance with the
soundtrack language.
Press RETURN to exit
³If the language selected for the “1 Audio” is actually used during playback,
the subtitles will not appear.
³If another language is used during playback, the subtitles will appear in the
language selected at the setup “1 Audio”.
2
5
English
Other ¢¢¢¢
3
French
4
Spanish
Another language can be selected.¤
3
Menus
1
4
English (Factory preset)
Other ¢¢¢¢
2
French
3
Spanish
Another language can be selected.¤
¤Enter the language code if you select “Other”. (See the language code list below.) Press [CANCEL]
if you enter the wrong number.
Note
³If the language selected is not available on the disc, the language designated by each disc will be
selected.
There are cases where the language is recorded but the disc designates another language.
AvcdOperations
Language code list
6565: Afar
6890: Bhutani
6976: Greek
7285: Hungarian
7289: Armenian
7365: Interlingua
7378: Indonesian
7383: Icelandic
7384: Italian
7387: Hebrew
7465: Japanese
7473: Yiddish
7487: Javanese
7565: Georgian
7575: Kazakh
7576: Greenlandic
7577: Cambodian
7578: Kannada
7579: Korean
7679: Laotian
8084: Portuguese
8185: Quechua
8277: Rhaeto-Romance 8473: Tigrinya
8279: Romanian
8285: Russian
8365: Sanskrit
8368: Sindhi
8372: Serbo-Croatian
8373: Singhalese
8375: Slovak
8471: Tajik
8472: Thai
6566: Abkhazian
6570: Afrikaans
6577: Ameharic
6582: Arabic
6583: Assamese
6588: Aymara
6590: Azerbaijani
6665: Bashkir
6669: Byelorussian
6671: Bulgarian
6672: Bihari
6678: Bengali; Bangla
6679: Tibetan
6682: Breton
6765: Catalan
6779: Corsican
6783: Czech
7684: Lithuanian
7686: Latvian, Lettish
7771: Malagasy
7773: Maori
7775: Macedonian
7776: Malayalam
7778: Mongolian
7779: Moldavian
7782: Marathi
7783: Malay
7784: Maltese
7789: Burmese
7865: Nauru
7869: Nepali
7876: Dutch
6978: English
6979: Esperanto
6983: Spanish
6984: Estonian
6985: Basque
7065: Persian
7073: Finnish
7074: Fiji
7079: Faroese
7082: French
7089: Frisian
7165: Irish
7168: Scots Gaelic
7176: Galician
7178: Guarani
7185: Gujarati
7265: Hausa
7273: Hindi
8475: Turkmen
8476: Tagalog
8479: Tonga
8482: Turkish
8484: Tatar
8487: Twi
8575: Ukrainian
8582: Urdu
8590: Uzbek
8673: Vietnamese
8679: Volapük
8779: Wolof
8872: Xhosa
8979: Yoruba
9072: Chinese
9085: Zulu
8376: Slovenian
8377: Samoan
8378: Shona
8379: Somali
8381: Albanian
8382: Serbian
8385: Sundanese
8386: Swedish
8387: Swahili
8465: Tamil
7583: Kashmiri
7585: Kurdish
7589: Kirghiz
7879: Norwegian
7982: Oriya
8065: Punjabi
8076: Polish
6789: Welsh
6865: Danish
7665: Latin
6869: German
7282: Croatian
7678: Lingala
8083: Pashto, Pushto
8469: Telugu
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing initial settings
2 Ratings
[DVD]
See page 28 for operation.
Level 8 (Factory preset)
All DVDs can be played.
Please set a rating limit
8 No Limit
7
6
Level 7 to 1
5
Prevents play of DVDs with ratings recorded on them (those that contain adult or violent scenes).
Level 0
Playback of all DVDs is prohibited (e.g. to prohibit playback of DVDs for adults which are not
encoded with rating information).
4
3
2
1
0 Lock All
Press RETURN to exit
Note
³The rating method differs from disc to disc. There are discs designed for adults that do not have these
ratings recorded on them. These discs can be played as normal. To prevent play of these discs, set the
rating limit to “0 Lock All”.
Setting ratings (When the level is “8”)
1 Select the level with the cursor buttons [3, 4] and press
Ratings
Enter a 4-digit password,
then press ENTER.
[ENTER].
2 Enter a 4-digit password with the numeric buttons and
press [ENTER].
****
³Press [CANCEL] if you enter the wrong number.
The lock symbol appears closed to show the rating is locked.
Do not forget your password.
Press RETURN to exit
3 Press [ENTER].
AcvdOperations
Setting is finished and the initial settings screen is displayed.
Your selection exceeds the
Now when you insert a DVD that exceeds the ratings limits
player’s rating limit. Do you
Ratings
The player is locked.
Remember the password.
want to change the limit?
you set, a message appears on the television.
If you want to play the disc, select “Yes” and enter your pass-
Yes
No
word. The unit will unlock temporarily, locking again when the
disc tray is opened or the unit is turned off.
4 3 4 3
Press ENTER to continue
Example: “4343”
Changing ratings (When the level is “0” to “7”)
Changes to the settings also requires a password.
Ratings
1 Press the cursor buttons [3, 4] to select “2 Ratings” in the
1 Unlock Player
2 Change Password
3 Change Level
initial settings screen and press [ENTER].
2 Enter your 4-digit password with the numeric buttons and
press [ENTER].
4 Temporary Unlock
Press RETURN to exit
3 Press the cursor buttons [3, 4] to select the item.
To unlock the player (the rating level returns to 8)
Select “1” and then press [ENTER].
To change the password
Select “2” and press [ENTER]. Enter a new 4-digit password and press [ENTER], then press
[ENTER] again.
To change the rating level
Select “3” and press [ENTER]. Select a new level with the cursor buttons [3, 4], then press
[ENTER].
To unlock the player temporarily
Select “4” and then press [ENTER].
³The rating is unlocked temporarily for the current disc. The player is locked again when the disc
30
tray is opened or the player is switched to the standby mode or turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Menu Language
See page 28 for operation.
Example: If you selected “2 Français”
1
2
3
English (Factory preset)
Français
Español
Select the language
for these Menus.
Choisissez la langue des
menus du lecteur.
1
2
3
English
Français
Español
1
2
3
English
Français
Español
Press RETURN to exit
Appuyez sur RETURN pour quitter
4 On-Screen Messages
See page 28 for operation.
1
On-Screen Messages
Color and Position
1
2
On (Factory preset)
Off
On-Screen Messages
1
2
On-Screen Messages On
Color and Position
2
1
2
3
4
5
6
Blue (Factory preset)
Blue
Violet
Green
Blue
Press RETURN to exit
Violet
Green
Shown slightly lower. Select if the
top of the screen is cut off.
AvcdOperations
5 FL Display
See page 28 for operation.
1
2
Bright (Factory preset)
Dim
FL Display
1 Bright
2 Dim
Press RETURN to exit
6 TV Aspect
See page 28 for operation.
Preparation
³Switch the video input mode on the television to suit the type of connection you have made (e.g.,
VCR 2).
Select your TV aspect
1
2
4 : 3
1
4:3: (Factory preset)
Select when a conventional television is connected.
16 : 9
2
16:9:
Select when a wide-screen television is connected.
Press RETURN to exit
For your reference
³For further details on the images which appear on the TV screen, see page 35.
³The optimum settings for your television may differ to those shown above.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing initial settings
7 Digital Audio Output
See page 28 for operation.
1
PCM Down
Conversion¤1
1
2
No (Factory preset)
Digital Audio Output
When playing a DVD recorded in 96 kHz linear PCM, signal
of 96 kHz/24 bit sampling frequency will be output and you
can enjoy high quality sound. If the DVD is copyright-
protected, no digital signal will be output unless converted to
48 kHz.
³Signal of 48 kHz linear PCM can be output from digital
audio output terminal irrespective of the setting.
Yes
1
2
3
PCM Down Conversion No
Select whether to output
audio on DVD recorded in
96 kHz linear PCM as it is
(No) or to convert it to
48 kHz for output (Yes).
Dolby Digital
Bitstream
DTS Digital Surround Off
Press RETURN to exit
When playing a DVD recorded in 96 kHz linear PCM, signal
is converted to 48 kHz/16 bit and can be output from digital
audio output terminal even if the DVD is copyright-protected.
2
Dolby Digital
1
2
Bitstream¤2 (Factory preset)
Dolby Digital bitstream (1ch–5.1ch) is output during playback
of DVDs recorded in Dolby Digital.
To select the signal format
(Bitstream or PCM) to be
output from the optical
digital audio output
terminal during playback of
DVDs recorded in Dolby
Digital.
PCM
Digital audio converted to 48 kHz/16 bit PCM (2ch) is output
during playback of DVDs recorded in Dolby Digital.
3
DTS Digital Surround
To select whether DTS
Digital Surround bitstream
is output from the optical
digital audio output
terminal or no digital audio
is output during playback
of DVDs recorded in DTS
Digital Surround.
1
2
Off (Factory preset)
No digital audio is output during playback of DVDs recorded
in DTS Digital Surround.
Bitstream¤2
DTS Digital Surround bitstream (1ch–5.1ch) is output during
playback of DVDs recorded in DTS Digital Surround.
AcvdOperations
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended setting of “Digital Audio Output”
Adjust settings as shown in table below depending on the kind of equipment that is connected to the optical digital audio output terminal.
Recommended setting
Type of equipment connected
1 PCM Down Conversion¤1
2 Dolby Digital
Bitstream
3 DTS Digital Surround
No digital equipment is connected
No
Off
Off
Dolby Digital decoder (á page 9)
Yes
Bitstream
DTS Digital Surround decoder
(á page 9)
Yes
Yes
Yes
PCM
Bitstream
Bitstream
Off¤2
Dolby Digital/DTS Digital Surround
decoder (á page 9)
Bitstream
PCM¤2
Digital audio equipment (no decoder)
(á page 11)
³Underlined items are factory preset.
¤1 Select “No” if the digital audio input terminal of your audio equipment (AV amplifier, etc.) can handle 96 kHz/24 bit signal. If it is not acceptable
for 96 kHz/24 bit digital audio signal, or the 96 kHz linear PCM disc you want to play is copyright-protected, it is recommended to set “1 No” and
make analog connection to enjoy high quality sound (If it is set to “Yes”, the player converts linear PCM to 48 kHz even during analog output).
¤2 When connecting an amplifier (with an optical digital input terminal) which does not contain a Dolby Digital or DTS Digital Surround decoder, be
sure to select “PCM” at “2 Dolby Digital” and “Off” at “3 DTS Digital Surround”. If “Bitstream” is selected, any attempt to play DVDs (or CDs
encoded with DTS) may cause a high level of noise that can injure your ears and damage your speakers.
For your reference
³Dolby Digital is a digital sound compression technique developed by Dolby Laboratories.
Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficient-
ly recorded on a disc.
³DTS Digital Surround is a 5.1-channel surround sound system, which is widely used in movie theaters around the world. The separation between
channels is good and provides a very real surround effect.
³Linear PCM is an uncompressed digital audio signal. While a CD is recorded in 44.1 kHz/16 bit, a DVD is recorded in 48 kHz/16 bit up to 96 kHz/
24 bit. Therefore, the sound reproduced with these signals is potentially better than that found on CDs. This player reproduces linear PCM in two
channels.
³Bitstream is a compressed digital audio signal. This signal can be decoded into different channels to produce, for instance, 5.1-channel surround
sound.
³The digital audio output terminal (optical) converts electrical signals into optical signals and transfers them to an amplifier. These optical signals
are immune from electrical interference, and they also have minimal effect on other equipment.
³These changes to digital audio output must be made, otherwise bitstream signals the decoder cannot handle will be output. If these
signals are output, “noise” will be output which can cause harm to your ears and speakers.
Note
³You cannot use DTS Digital Surround decoders not suited to DVD.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. C 1992–1997
Dolby Laboratories. All rights reserved.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing initial settings
9 Other Settings
See page 28 for operation.
1
Still Mode
1
2
Automatic (Factory preset)
Field
Other Settings
Select either “Field still” or
“Frame still” in the still
picture mode.
Select this setting when jittering occurs in the still picture
mode when “1 Automatic” is selected.
Frame
Select if small text or fine patterns cannot be seen clearly in
the still picture mode when “1 Automatic” is selected.
1 Still Mode
Automatic
2 Audio during Search On
3 TV Mode (4:3)
4 D. Range Compression Off
5 Still Picture Display
6 Black Level Control
Pan&Scan
3
Off
Lighter
Press RETURN to exit
2
3
Audio during Search
To select whether audio is
heard or not during search
(forward direction) at the
initial search speed.
1
2
On (Factory preset)
Off
TV Mode (4:3)
1
2
Pan & Scan (Factory preset)
To select whether wide-
screen material is played
in the pan and scan style
or in the letterbox style on
a conventional TV (4:3).
Wide-screen video material will be played in the pan and
scan style (the picture is shown with either one or both sides
cut off) on a conventional television (4:3).
³Video material not formatted in the pan and scan style will
be played back in the letterbox style.
Letterbox
Wide-screen video material will be played in the letterbox
style (black bands appear at the top and bottom of the
screen) on a conventional television (4:3).
4
D.(Dynamic) Range
Compression
1
2
Off (Factory preset)
The dynamic range remains as it was recorded on the disc.
On
Dynamic range is compressed by increasing soft sounds and
reducing loud sounds. Select when viewing discs at low
volume, such as late at night.
To compress the dynamic
range (the difference
between the loudest sound
and the softest sound),
making it easier to hear
dialogue even at low
volume. This function only
works with Dolby Digital
DVD.
5
6
Still Picture Display
To display the picture type
(DVD), I, P or B in the still
picture mode.
1
2
Off (Factory preset)
On
Still (P)
Example: P-picture
Black Level Control
To select the black level of
the picture, “Lighter” or
“Darker”.
1
2
Lighter (Factory preset)
Select when the player is connected to a TV through the
VIDEO OUT terminal or S VIDEO OUT terminal.
Darker
Select when the player is connected to a TV through the
COMPONENT VIDEO OUT (Y/PB/PR) terminals.
Note
³Audio is heard at any speed when playing CDs, regardless of any settings at “2 Audio during Search”.
³Audio is not heard at any speed when playing CDs encoded with DTS, regardless of any settings at
“2 Audio during Search”.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
For your reference
³I/P/B
To efficiently store video on DVD, common elements among frames are used in common, and different elements are recorded with each individual
frame. The frame that contains the common elements is called an I-picture, a complete frame in itself. A P-picture is calculated from past I or
P-pictures. The frame that fills in the spaces between the I-and P-pictures is called the B-picture.
I-pictures have the best picture quality, so they should be used when making picture adjustments.
³Frame
Individual images in a video or on the television are called frames.
³Field
Half of the video information (video signal) in a frame is called a field. With conventional TV systems, a single frame (a single screen) consists of
two fields.
³Frame still
The two fields are displayed alternately on the TV screen, so the image may be blurry. However, the image quality is better than field images.
³Field still
Only one field (half of the video information) is displayed on the TV screen, so the apparent resolution is low. However, there is no blurring on the
screen.
How different kinds of software appear on your television
DVD software is recorded in a variety of picture formats, and how they appear on your TV depends on the software, the kind of TV you have, and the
picture mode your TV is set to.
³Letterbox refers to pictures where black bands appear at the top and bottom.
³Pan and scan refers to pictures where part of the picture is cut off so it fills the whole screen.
Television and
picture mode
16:9
full mode
16:9
zoom mode
16:9
auto mode
4:3
Software format
Wide-screen, pan and scan
Edges cut off.
Full screen
Top and bottom cut off
Full screen
Wide-screen, non-pan and
scan
Letterbox
Regular (4:3)
Full screen
Screen stretched
horizontally
Top and bottom cut off
Full screen with black
bands at right and left
Regular (4:3) letterbox
Letterbox
Letterbox with screen
stretched horizontally
Full screen
Letterbox with
extremities of picture
stretched.
The names given to the television picture modes depends on the make of your television. There may also be slight differences in how the pictures
appear on the screen. Refer to your television’s operating instructions for details.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Before requesting service for this player, check the chart below for a possible cause of the problem you are experiencing. Some simple checks or
a minor adjustment on your part may eliminate the problem and restore proper operation.
If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, contact your authorized
YAMAHA dealer or service center for instructions.
Reference pages are shown as black circled numbers 6.
Common Problems
No power.
Insert the AC power supply cord securely into the household AC outlet. 9
The player is automatically
To conserve power, the player is automatically switched to the standby mode after approx.
switched to the standby mode.
30 minutes elapsed in the stop mode (Auto power-off function). Turn the power back to ON.
Play fails to start even when
[1 PLAY] is pressed.
Play starts but then stops
immediately.
Condensation has formed: wait about 1 to 2 hours for it to evaporate.
This player cannot play discs other than DVD, Video CD and CD. 6
DVDs with a region number other than “1” or “ALL” cannot be played. DVDs with multiple region
numbers including “1” can be played. 6
The disc may be dirty and may require cleaning. V
Ensure that the disc is installed with the label of the side to be played facing upwards. >
No picture.
Ensure that the equipment is connected properly. < =
Ensure the television’s video input setting (e.g. VCR2) is correct.
No sound.
Distorted sound.
Ensure that the equipment is connected properly. 8–=
Ensure that the input settings for the television and stereo system are correct.
Turn V.S.S. off if it is on. E K
Picture is distorted during rapid
advance or rapid reverse.
The picture will be somewhat distorted at times: this is normal.
No key operation (by the player
and/or the remote control) is
effective.
Some operations may be prohibited by the disc.
Press [STANDBY/ON] to switch the player to the standby mode and then back to ON. Alternatively,
press [STANDBY/ON] to switch the player to the standby mode, disconnect the AC power supply
cord and then reconnect it. (The player may not be operating properly due to lightning, static
electricity or some other external factor.)
The picture shown on the
television is not normal.
Go to the initial settings menu “6 TV Aspect” and change the setting to suit your television. You may
also need to change the screen mode on the television itself. O S
(The sides of the picture are cut
off or black bands appear at the
top and bottom of the screen.)
No on-screen display.
The “Off” setting is selected for “1 On-Screen Messages” in “4 On-Screen Messages”:
select “On”. O
On-Screen Menu Icons not
displayed or only partially
displayed on the TV screen.
Change the position of the On-Screen Menu Icons using “2 Color and Position” in “4 On-Screen
Messages” of the initial settings. O
The language for the player’s
menus and on-screen messages is
wrong.
Go to the initial settings menu “3 Menu Language” and change the language. O
No operations can be performed
with the remote control.
To conserve power, the player is automatically switched to the standby mode after approx.
30 minutes have elapsed in the stop mode (Auto power-off function). Turn the power back to ON.
Check the batteries are installed with the correct polarities (i and j). 5
The batteries are depleted: replace them with new ones. 5
Point the remote control at the remote control sensor and operate. 5
Operate the remote control at a distance of not more than 23 feet (7 m) from the remote control
sensor. 5
Remove the obstacles between the remote control and remote control sensor. 5
36
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD
No subtitles.
Subtitles appear only with discs which contain them.
Subtitles are cleared from the TV monitor. Display the subtitles. D J
Alternative soundtrack (or
subtitle) languages fail to be
selected.
An alternative language is not selected with discs which do not contain more than one language.
In the case of some discs, the alternative language cannot be selected by operating the [AUDIO] or
[SUBTITLE]. Try selecting it from the disc’s menu if one is available. B
Angle cannot be changed.
This function is dependent on software availability. Even if a disc has a number of angles recorded,
these angles may be recorded for specific scenes only (when “ANGLE” lights up on the player’s FL
display).
Soundtrack and/or subtitle
language is not the one selected
at the initial settings.
If the soundtrack and/or subtitle language does not exist on the disc, the language selected at the
initial settings will not be seen/heard.
The disc’s menu is displayed in
The setup “3 Menus” of “1 Disc Languages” is set to French: select English.
French (example).
Sound does not come from a
speaker.
Check the connections. 8–=
If you have a subwoofer connected to this player, use the On-Screen Menu Icons with the remote
control to turn subwoofer output on. K
If you have connected this player to an AV amplifier (with built-in decoder) through the digital audio
output terminal, go to the initial settings menu “7 Digital Audio Output” and change the settings to
“Bitstream” for “2 Dolby Digital” or “3 DTS Digital Surround”. P
Sound will only come from the two main speakers if V.S.S. is on.
Turn V.S.S. off. E K
The password for rating level has
been forgotten.
Reset all the settings to Factory
Preset.
While stopped, press and hold [:] and [;] on the player and then also press and hold [< OPEN/
CLOSE] on the player until “Initialized” disappears from the television (after about 3 seconds).
All initial settings will return to the default values.
The vocals cannot be turned off.
You have selected an audio channel that includes a vocal channel. Read the disc’s jacket to choose
the correct channel. C
A menu is shown after playing
each song on a Karaoke DVD.
Most Karaoke DVDs are designed to do this. Some discs have an item in the menu that allows you
to play all the songs.
Video CD
No menu play.
This function works only for Video CDs with playback control. 6
Self-diagnosis display function
When an error or trouble is detected during operation, a message appears in the FL display.
When a message has appeared, check the details given below.
Message
Player status
Remedy
CHECK THE DISC
Disc is dirty.
Wipe the disc clean.
Trouble is likely to have occurred. The
number following “H” differs depending on
the status of the player.
Press [STANDBY/ON] to switch the player to the standby mode
and then back to ON. Alternatively, press [STANDBY/ON] to
switch the player to the standby mode, disconnect the AC power
supply cord, and then reconnect it.
H ¸ ¸
¸ ¸ stands
for a number.
³If the message fails to be cleared, even when remedial action is taken, ask a service technician to repair the player.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc handling
Maintenance
Choose discs with these marks:
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a soap-
and-water solution or a weak detergent solution.
³Never use alcohol, paint thinner or benzine to clean this unit.
³Before using chemically treated cloth, read the instructions that
came with the cloth carefully.
However, do not use irregulary shaped discs, such as heart-shaped.
(Discs of the sort can damage the player.)
º How to hold a disc
Do not touch the recorded surface.
º If the surface is dirty
Wipe it with a damp cloth and then wipe dry.
º If the disc is brought from a cold to a warm envi-
ronment, moisture may form on the disc
Wipe with a soft, dry, lint-free cloth before using the disc.
º Handling precautions
³Do not write on the label side with a ball-point pen or other writing
instrument.
³Do not use record cleaning sprays, benzine, thinner, static electric-
ity prevention liquids or any other solvent.
³Do not attach labels or stickers to discs. (Do not use discs with ex-
posed adhesive from tape or left over peeled off stickers.)
³Do not use scratch-proof protectors or covers other than those
specified for use with this player.
º Do not place or store discs in the following
places
³Locations exposed to direct sunlight
³Humid or dusty locations
³Locations directly exposed to a heat vent or heating appliance
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power supply:
U.S.A. and Canada models: AC 120 V, 60 Hz
Component video output:
Asia and Australia models:
Y output level:
U.K. and Europe models:
Australia model:
Asia model:
Power consumption:
Dimensions:
AC 220–240 V, 50 Hz
AC 220–240 V, 50 Hz
AC 110–240 V, 50/60 Hz
14 W
171/8q (W)k107/8q (D)k37/8q (H)
[435 (W)k276 (D)k99 (H) mm]
7 lbs. 4 oz (3.3 kg)
1 Vp-p (75 -)
PB output level:
PR output level:
Output terminal:
0.7 Vp-p (75 -)
0.7 Vp-p (75 -)
Pin jack
(Y: green, PB: blue, PR: red)
Scart video terminal:
U.K. and Europe models:
Audio output:
Mass:
Signal system:
U.S.A. and Canada models: NTSC
U.K., Europe and
Output level:
Output terminal:
2 Vrms (1 kHz, 0 dB)
Pin jack
Australia models:
General model:
PAL 625/50, PAL 525/60
PAL/NTSC
Mixed output (L/R):
Subwoofer output:
1 system
1 system
Operating temperature range:
Audio signal output characteristics:
i41 to i95 oF (i5 to i35 oC)
(1) Frequency response:
Operating humidity range:
Discs played:
(1) DVD-Video disc
5 to 90 % RH (no condensation)
³DVD (linear audio):
2 Hz–22 kHz (48 kHz sampling)
2 Hz–44 kHz (96 kHz sampling)
2 Hz–20 kHz (EIAJ)
³CD audio:
5q (12 cm) single-sided, single-layer
5q (12 cm) single-sided, dual-layer
5q (12 cm) double-sided, single-layer
3q (8 cm) single-sided, single-layer
3q (8 cm) single-sided, dual-layer
3q (8 cm) double-sided, single-layer
(2) Compact disc (CD-DA, Video CD)
5q (12 cm) disc
(2) S/N ratio:
³CD audio:
(3) Dynamic range:
³DVD (linear audio):
³CD audio:
(4) Total harmonic distortion:
³CD audio:
115 dB (EIAJ)
102 dB
98 dB (EIAJ)
0.0025 % (EIAJ)
Optical terminal
Digital audio output:
Optical digital output:
3q (8 cm) disc
Video output:
Output level:
1 Vp-p (75 -)
Pin jack
1 system
Pickup:
Wave length:
Laser power:
Laser output:
665 nm
CLASS II
Max. 1.0 mW (Continuous)
Output terminal:
Number of terminals:
S video output:
Y output level:
C output level:
Output terminal:
Number of terminals:
1 Vp-p (75 -)
0.286 Vp-p (75 -)
S terminal
Power consumption in standby mode:
approx. 2.0 W
1 system
Note
Specifications are subject to change without notice.
Mass and dimensions are approximate.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual
property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. PA PARIS-EST RUE AMBROISE CROIZAT CROISSY-BEAUBOURG BP70-77312 MARNE LAVALLEE, CEDEX 2 FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|