Xyron Laminator ProFinishTM Jr User Manual

Makes  
items up  
to 9" wide.  
*
Use it  
anywhere!  
No heat.  
No electricity.  
No batteries.  
* Adhesive cartridge 9" wide,  
all others 8.5" wide.  
USER’S MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
With just a few simple, easy-to-follow steps, you’ll be protecting and enhancing  
your documents and projects:  
Getting Started  
Step 1:  
Place item flat on the tray, aligned all the way to the left side. Guide the item  
forward while slowly turning the handle clockwise.  
Step 2:  
After the item is completely visible on the output tray, trim the item by sliding  
the blade across the material.  
Step 3:  
Gently lift up the cutter tray and slide it out. Use the cutter to trim the rest of the  
item if necessary. For adhesive, remove the clear mask and peel off the  
sticky-back item.  
How to replace the cutter assembly:  
Align the cutter sides with the machine. Slide in the cutter with the cut bar resting  
on the spring arms on the side of the machine until it snaps and locks into place.  
How to replace the cut blade:  
Loosen and remove the screw in the cut bar with wrench. Remove colored  
plastic insert and slide the old blade off the cut bar (safely discard old blade).  
Carefully slide the NEW ProFinish Jr. blade onto clear bar. NOTE: The sharp  
edge of the blade should be facing inward. Replace the colored plastic insert into  
clear bar and secure screw with wrench. Verify smooth movement across the  
entire length of the clear bar.  
How to load the cartridge:  
Open the lid to your ProFinish Jr. machine. Slide the cartridge into the tracks on  
the sides of the machine with the exposed rolls of material facing the open lid  
cover. Close the lid securely. Advance film and trim.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Helpful Hints  
G
Make sure the cartridge is installed correctly prior to using the machine.  
G
For best results, turn the handle slowly.  
G
Arrange small items (without overlapping them) on the feed tray to  
maximize your cartridge material use.  
G
Use items that are 1/10 of an inch thick or less.  
G
Test before using one-of-a-kind items.  
G
Watch for the End-of-Roll marker 18 inches from the end of Laminate and  
Magnet cartridges. To remove marker, simply peel it off the laminate.  
Adhesive Supply:  
G
For best results, apply pressure with finger or dull tool around the edge of the object prior to  
removing the clear plastic film.  
G
If there is excess adhesive around the edges of an item, simply wipe off with your fingers. The  
adhesive comes right off without sticking to your hands.  
G
Clean off adhesive buildup from the rollers with any adhesive remover or rubbing alcohol.  
G
Acid-Free Permanent Adhesive is safe for scrapbooking. Acid-Free Repositionable Adhesive is  
safe for windows, painted walls and doors, and it does not leave any residue on most surfaces.  
Test on an inconspicuous area first.  
Laminate Supply:  
G
It is not recommended for one-of-a-kind items since the process is permanent  
(use copies of photos and other valuable items).  
G
Make sure there is adequate space between each item you are laminating. Overlapping will  
cause the items to be laminated together.  
G
Two-Sided Lamination allows you to cut right to the edge or completely through the item you are  
protecting. It will not separate!  
Magnet Supply:  
G
To maximize the material when making a magnet frame, place a smaller item in the middle of the  
frame. This way, even the magnet material in the middle of the frame is being used. Keep other  
paper supplies and photos handy for magnetizing.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Machine Specifications  
Footprint:  
7.75" W x 14.5" L x 6.75" H (19.7 cm x 37 cm x 17.1 cm)  
Approximately 6 lbs (2.72 kg)  
Approximately 7 lbs (3.17 kg)  
0.10" (2.54 mm)  
Weight:  
Packed Weight:  
Maximum Document Thickness:  
Maximum Document Width:  
Maximum Document Length:  
Power Source:  
9" (22.86 cm)  
Cartridge Dependent  
NONE  
Cutter Assembly:  
Manufactured:  
Removable, with available replacement blade  
Some parts and assembly in both USA and China  
Replacement Cartridges  
Part Number  
9" x 50' Two-Sided Lamination  
200032-00  
200033-00  
200034-00  
200035-00  
9" x 40' One-Side Permanent Adhesive  
9" x 25' One-Side Laminate/One-Side Repositionable Adhesive  
8.5" x 10' One-Side Laminate/One-Side Magnetic  
Contact your local dealer to order replacement cartridges  
®
or call Varitronics at 800-328-0585  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
©2003 Brady Worldwide, Inc.  
All Rights Reserved  
20049-00 3/03  

Weslo Hot Tub WLHS20702 User Manual
Westinghouse Mixer WST2009ZE User Manual
Whirlpool Range FEP310KV3 User Manual
Wolf Ventilation Hood CT15G S User Manual
Xantech Stereo Amplifier XSS24100W User Manual
Xantech Universal Remote IR DC4 User Manual
Yamaha Stereo Amplifier DSP A780 User Manual
Zanussi Oven FM56 User Manual
Zanussi Oven ZCG 6200 User Manual
Zebra Technologies Crib RW 220 User Manual