Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Installation Guide
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system; 3x OEM Lock Remote Start Activation*, RF Kit or SmartStart (all sold
separately). Refer to page 24 for a list of RF kits and their part numbers.
*3x OEM Lock Remote Start Activation is a feature that allows users to control the aftermarket remote
starter using the factory (OEM) remote control. See page 2 for more information.
Note: Only available on certain models, check the Vehicle Application Guide for compatibility with
specific year and model.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle
completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to
start the vehicle from a distance. An RSR solution is commonly referred to as a Standalone installation.
Important!
This product is NOT compatible with vehicles equipped with a manual transmission.
Index
Important Information.............................................................................................................................................................................. 02
Vehicle Application Guide........................................................................................................................................................................ 03
Installation
Type 1a (with T-Harness)....................................................................................................................................................................... 04
Type 1b (without T-Harness).................................................................................................................................................................. 05
Type 2a (with T-Harness)....................................................................................................................................................................... 07
Type 2b (without T-Harness).................................................................................................................................................................. 08
Type 3a (with T-Harness)....................................................................................................................................................................... 10
Type 3b (without T-Harness).................................................................................................................................................................. 11
Type 4a (with T-Harness)....................................................................................................................................................................... 13
Type 4b (without T-Harness).................................................................................................................................................................. 14
Type 5 (without T-Harness).................................................................................................................................................................... 16
Programming
Module Programming and Reset for Installation Types 1 to 4................................................................................................................. 18
Module Programming and Reset for Installation Type 5......................................................................................................................... 20
Module Reset.......................................................................................................................................................................................... 21
Feature and Option List.......................................................................................................................................................................... 22
Feature Programming............................................................................................................................................................................. 22
LED Diagnostics and Troubleshooting.................................................................................................................................................... 23
Optional RF Kits...................................................................................................................................................................................... 24
Using a DBALL-CHRYSLER RSR.......................................................................................................................................................... 26
Limited One-Year Consumer Warranty................................................................................................................................................... 27
SmartStart Compatible
See page 2 for more information.
† Chrysler, Dodge, Jeep and Volkswagen are registered trademarks and property of their respective companies.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 3
Vehicle Application Guide
Vehicles
Chrysler
200
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
300/300c
300/300c
Aspen
2
2
3
2
•
•
4
3
5
4
3
4
4
5
•
•
•
•
•
•
•
3
5
4
3
3
3
1
Pacifica
5
4
5
5
PT Cruiser
Sebring
4
3
3
3
1
4
3
3
3
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Sebring Convertible
Sebring Sedan
Town & Country
Town & Country
Dodge
3
1
1
•
•
•
•
•
•
•
•
5
5
5
•
12 11 10 09 08
07
06
05 04
Avenger
3
3
1
3
3
1
3
3
1
3
3
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Caliber
3* or 4* 3* or 4*
Caravan
1
•
•
•
•
•
•
•
•
•
•
Caravan
5
5
5
5
•
Challenger
Challenger (Smart Key)
Charger
1
1
1
1
2
1
1
2
1
1
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Charger
4
3
4
•
•
Dakota
3
1
3
3
3
Durango
•
•
•
•
•
•
•
•
•
•
•
•
Durango
3
1
3
1
3
5
•
•
Grand Caravan
Grand Caravan
Journey
1
1
1
1
1
•
•
•
•
•
•
5
4
5
4
5
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Magnum
2
3
3
•
•
Magnum
4
3
•
•
Nitro
3
1
3
1
3
1
RAM
•
•
RAM
3
3* or 4*
•
Jeep
12 11 10 09 08
07
06
05 04
Commander
Commander
Compass
Grand Cherokee
Grand Cherokee
Grand Cherokee
Grand Cherokee (Smart Key)
Liberty
2
3
2
2
3
2
2
3
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
3
4
4
•
•
3
1
•
•
•
•
4
4
•
1
3
3
3
3
•
3
3
3
3
3
3
3
3
3
3
3
3
•
•
•
•
Patriot
3
3
3
3
3
Wrangler
Wrangler Unlimited
Mitsubishi
Raider
3
12 11 10 09 08
07
3
06
06
05 04
05 04
3
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Ram
12 11 10 09 08
07
1500
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2500
1
3500
1
C/V
1
•
•
•
•
•
•
•
•
Volkswagen
Routan
12 11 10 09 08
07
06
05 04
1
1
1
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
*To select the proper install type, locate the ignition switch connector and select your install type as illustrated below:
Installation Type 4
has a Start wire
Installation Type 3 does not
have a Start wire
5 or 6
1
5 or 6
1
Connector side view
at ignition switch
Connector side view
at ignition switch
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 4
Installation Type 1a (with T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
To vehicle’s
(+) Parking Lights
White/Purple
XOVER
CABLE
85
86
87
Hood Pin
87a
30
+12v
Fuse 15A
Neutral Safety Switch
ONLY connect for
Dodge Journey.
2: Green/Black: (-) Parking Lights via Relay*
OR*
See page 6 for
wiring information
6: White/Black: (-) Hood
8: Violet/Green: Parking Light MUX*
9: Violet/Brown: Parking Light MUX*
10: Yellow/Black: RAP OFF
(+) 12v
RF
RX
(-) Driver door pin
Programming button
LED
(-) Ground
DBALL
TX
Purple wire in
driver kick panel
Ignition
Barrel
CHTHD1
(optional)
Facing view
Behind Ignition Switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
*See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 5
Installation Type 1b (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
To vehicle’s
(+) Parking Lights
White/Purple
XOVER
CABLE
85
86
87
87a
Hood Pin
30
3: Tan/Black: HSCAN High
4: Tan: HSCAN Low
+12v
Fuse 15A
(+) 12v
7: Brown: (+) 12v
Neutral Safety Switch
ONLY connect for
Dodge Journey.
8: Yellow
9: Orange/Yellow
(+) 12v
(-) Ground
13: Red: (+) 12v
14: Black: (-) Ground
2: Green/Black: (-) Parking Lights via Relay*
OR*
6: White/Black: (-) Hood
See page 6 for
wiring information
8: Violet/Green: Parking Light MUX*
9: Violet/Brown: Parking Light MUX*
10: Yellow/Black: RAP OFF
(+) 12v
RX
RF
(-) Driver door pin
Programming button
(-) Ground
TX
DBALL
LED
Purple wire in
driver kick panel
Ignition
Barrel
1
7
6
Connector side view
at ignition switch
12
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
*See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 6
Parking Light Vehicle Wiring Reference Chart (Type 1)
Light switch,
black 10-pin plug
DBALL Output from
12 Pin connector
Vehicle
Years Vehicle Wire Location on vehicle
(+) / (-)
Chrysler
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Town & Country
2011+ White/Green
2008-10 White/Brown
Black connector at light switch, pin 3
MUX
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Town & Country
Black connector at light switch, pin 1
5
4
9
3
8
2
7
1
Dodge
10
6
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
2: Green/Black: (-) Parking Lights
via Relay
Caravan
2011+ White/Green
2008-10 White/Brown
2008-11 White/Brown
Black connector at light switch, pin 3
Black connector at light switch, pin 1
Black connector at light switch, pin 1
Black connector at light switch, pin 1
Black connector at light switch, pin 3
Black connector at light switch, pin 3
Black connector at light switch, pin 1
Passenger kick panel
MUX
MUX
MUX
MUX
MUX
MUX
MUX
(+)
Caravan
Challenger
Light switch,
black 6-pin plug
Challenger (Smart Key) 2008-11 White/Brown
Durango
2011+ White/Green
2011+ White/Green
2008-10 White/Brown
2009-10 White/Purple
2009-12 White
Grand Caravan
Grand Caravan
Journey
6
5
4
3
2
1
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
RAM
Black connector at light switch, pin 1
MUX
Jeep
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Grand Cherokee
2011+ White/Green
2011+ White/Green
Black connector at light switch, pin 1
Black connector at light switch, pin 1
MUX
MUX
Grand Cherokee
(Smart Key)
Ram
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
1500
2012 White
2012 White
2012 White
2012 White
Black connector at light switch, pin 1
Black connector at light switch, pin 1
Black connector at light switch, pin 1
Black connector at light switch, pin 1
MUX
MUX
MUX
MUX
2500
3500
C/V
Volkswagen
Routan
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
2011+ White/Green
2009-10 White/Brown
Black connector at light switch, pin 3
Black connector at light switch, pin 1
MUX
MUX
Routan
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 7
Installation Type 2a (with T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
Twisted pair in the kick panel
White/Orange
White/Gray, White
or White/Pink
Neutral Safety Switch
5: White/Orange: FTCAN High
6: White: FTCAN Low
2: Green/Black: (-) Parking Lights*
OR*
6: White/Black: (-) Hood
See page 9 for
wiring information
8: Violet/Green: Parking Light MUX*
9: Violet/Brown: Parking Light MUX*
10: Yellow/Black: RAP OFF
(-) Driver door pin
(+) 12v
RX
RF
Programming button
LED
Purple wire in
driver kick panel
(-) Ground
TX
DBALL
CHTHD1
(optional)
Ignition
Barrel
Facing view
Behind Ignition Switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
*See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 8
Installation Type 2b (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
Twisted pair in the kick panel
White/Orange
White/Gray, White
or White/Pink
5: White/Orange: FTCAN High
6: White: FTCAN Low
Neutral Safety Switch
3: Tan/Black: HSCAN High
4: Tan: HSCAN Low
(+) 12v
7: Brown: (+) 12v
8: Yellow
9: Orange/Yellow
(+) 12v
(-) Ground
13: Red: (+) 12v
14: Black: (-) Ground
2: Green/Black: (-) Parking Lights*
OR*
6: White/Black: (-) Hood
See page 9 for
wiring information
8: Violet/Green: Parking Light MUX*
9: Violet/Brown: Parking Light MUX*
10: Yellow/Black: RAP OFF
(+) 12v
RX
RF
(-) Driver door pin
Programming button
LED
(-) Ground
TX
DBALL
Purple wire in
driver kick panel
1
6
Connector side view
at ignition switch
Ignition
Barrel
12
7
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
*See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 9
Parking Light Vehicle Wiring Reference Chart (Type 2)
Light switch,
black 10-pin plug
DBALL Output from
12 Pin connector
Vehicle
Years Vehicle Wire Location on vehicle
(+) / (-)
Chrysler
300/300c
Dodge
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
2008-10 White/Brown
Black connector at light switch, pin 1
MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Charger
2008-10 White/Brown
2008 White/Brown
Black connector at light switch, pin 1
Black connector at light switch, pin 1
MUX
MUX
1 2 3 4 5
6 7 8 9 10
Magnum
Jeep
Commander
2008-10 White/Dk. Blue Hazar light switch
(-)
(-)
2: Green/Black: (-) Parking Lights
2: Green/Black: (-) Parking Lights
Grand Cherokee 2008-10 White/Dk. Blue Hazar light switch
Jeep Commander & Jeep
Grand Cherokee
Optional parking light connection
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 10
Installation Type 3a (with T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
See page 12 for
wiring information
Neutral Safety Switch
2: Green/Black: (-) Parking Lights
10: Yellow/Black: RAP OFF
6: White/Black: (-) Hood
To vehicle’s
(+) Parking Lights
(-) Driver door pin
(+) 12v
RX
RF
Programming button
(-) Ground
TX
Purple wire in
driver kick panel
85
86
87
DBALL
LED
87a
30
+12v
Fuse 15A
CHTHD2
(optional)
1
8
Connector side view
at ignition switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 11
Installation Type 3b (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
See page 12 for
wiring information
XOVER
CABLE
Hood Pin
To vehicle’s
(+) Parking Lights
3: Tan/Black: HSCAN High
85
86
87
Neutral Safety Switch
87a
4: Tan: HSCAN Low
7: Brown: (+) 12v
30
(+) 12v
8: Yellow: (+) Ignition
(+) 12v
(-) Ground
13: Red: (+) 12v
14: Black: (-) Ground
+12v
Fuse 15A
8: Violet/Green: Multiplex Output
9: Violet/Brown: Multiplex Output
6: White/Black: (-) Hood
2: Green/Black: (-) Parking Lights
(-) Driver door pin
10: Yellow/Black: RAP OFF
Purple wire in
driver kick panel
(+) 12v
RF
RX
Programming button
LED
(-) Ground
DBALL
TX
1
8
Connector side view
at ignition switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 12
Parking Light Vehicle Wiring Reference Chart (Type 3)
Vehicle
Years Wire
(+) / (-) Location
Chrysler
200
2011 White/Violet
2007-09 Pink/Red
(+) Driver kick panel
Aspen
(+) Driver kick fuse box, black 40-pin plug, pin 6
(+) Driver kick panel
Sebring
2007-10 White/Violet
2008-10 White/Violet
2007-10 White/Violet
Sebring Convertible
Sebring Sedan
Dodge
(+) Driver kick panel
(+) Driver kick panel
Avenger
Caliber
2008-11 White/Violet
2007-11 White/Violet
2007-11 Pink/Red
(+) Driver kick panel
(+) Driver kick panel
Dakota
(+) Underhood fuse box, black 20-pin plug, pin 15
(+) Driver kick fuse box, black 40-pin plug, pin 6
(+) Driver kick panel
Durango
Nitro
2007-09 Pink/Red
2007-11 White/Violet
2006-08 White/Gray
RAM
(+) Above driver kick, gray 74-pin plug, pin 19
Jeep
Compass
Liberty
2007-11 White/Violet
2008-10 White/Violet
2007-12 White/Violet
2007-12 White/Violet
2007-12 White/Violet
(+) Driver kick panel
(+) Driver kick panel
(+) Driver kick panel
(+) Passenger kick panel
(+) Passenger kick panel
Patriot
Wrangler
Wrangler Limited
Mitsubishi
Raider
2007-09 Pink/Red
(+) Underhood fuse box, black 20-pin plug, pin 15
Driver kick fuse box,
black 40-pin plug
Underhood fuse box,
black 20-pin plug
Above driver kick,
gray 74-pin plug
1
7
38 44
10 9
8
7
6
5
4
3
2
1
46
55
3
20 19 18 17 16 15 14 13 12 11
25
28
39
37
9
1
3
10
58
11
59
60
61
12
14
15
16
33 21
17
5
8
64
17
36 24
20
65
72
29
13
20
29
38
40
4
2
32
16
31 37 68 74
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 13
Installation Type 4a (with T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
(+) Parking Lights
Neutral Safety Switch
See page 15 for
wiring information.
11: Yellow/Red: (+) Start
2: Green/Black: (-) Parking Lights
To vehicle’s
(+) Parking Lights
6: White/Black: (-) Hood
85
86
87
87a
30
(+) 12v
RX
RF
Programming button
(-) Ground
TX
+12v
Fuse 15A
DBALL
LED
CHTHD2
(optional)
1
8
Connector side view
at ignition switch
Violet/Brown, Pin 2
5 or 6
1
Cut Purple/Brown
wire, Pin 8
(on female end)
Connector side view
at ignition switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 14
Installation Type 4b (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
(+) Parking Lights
To vehicle’s
(+) Parking Lights
XOVER
CABLE
See page 15 for
wiring information.
85
86
87
87a
30
Hood Pin
+12v
Fuse 15A
3: Tan/Black: HSCAN High
4: Tan: HSCAN Low
Neutral Safety Switch
(+) 12v
7: Brown: (+) 12v
8: Yellow: (+) Ignition
11: Yellow/Red: (+) Start
12: Brown/Red: (+) 12v
13: Red: (+) 12v
(+) 12v
(+) 12v
(-) Ground
14: Black: (-) Ground
2: Green/Black: (-) Parking Lights
6: White/Black: (-) Hood
8: Violet/Green: Multiplex Output
9: Violet/Brown: Multiplex Output
(+) 12v
RF
RX
Programming button
LED
(-) Ground
DBALL
TX
5 or 6
1
1
8
Connector side view
at ignition switch
Connector side view
at ignition switch
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 15
Parking Light Vehicle Wiring Reference Chart (Type 4)
Vehicle
Years Wire
(+) / (-) Location
Chrysler
300/300c
PT Cruiser
Dodge
2005-07 White/Violet
2006-10 White/Violet
(+) Passenger kick panel
(+) Driver kick panel
Caliber
2007-11 White/Violet
2006-07 White/Violet
2005-07 White/Violet
2006 White/Gray
(+) Driver kick panel
Charger
Magnum
RAM
(+) Passenger kick panel
(+) Passenger kick panel
(+) Above driver kick, gray 74-pin plug, pin 19
Jeep
Commander
2006-07 White/Dk. Blue
2005-07 White/Dk. Blue
(-)
(-)
Hazard light switch
Hazard light switch
Grand Cherokee
Above driver kick,
gray 74-pin plug
1
7
38 44
46
55
3
10
58
11
59
60
61
14
15
16
64
17
65
72
20
29
31 37 68 74
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 16
Installation Type 5 (without T-Harness)
Important!
The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the DBALL.
The optional XL202 and antenna are not included and MUST be
purchased separately.
SmartStart is optional and not included. It MUST be purchased
separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
(+)12v
OR
LED
Programming
Button
5 pins
TX
(-) Ground
4 pins
RX
XL202
SmartStart
RX
(-) Ground
LED
2 pins
D2D (4 pins, white)
TX
(+)12v
You can either connect to an XL202 module
or to a SmartStart module.
XOVER
CABLE
Hood Pin
2: Violet/Yellow: J1850
8: Yellow
9: Orange/Yellow
Neutral Safety Switch
11: Yellow/Red: (+) Start
12: Brown/Red: (+) 12v
13: Red: (+) 12v
(+) 12v
(+) 12v
(-) Ground
Parking Lights
14: Black: (-) Ground
2: Green/Black: (-) Parking Lights
7: Gray/Black: (+) Ignition
See page 17 for
wiring information
6: White/Black: (-) Hood
8: Violet/Green: Multiplex Output
9: Violet/Brown: Multiplex Output
(+) 12v
RX
RF
Sentry Key
(+) Ignition
Programming button
(-) Ground
TX
J1850
DBALL
LED
6
1
1
Connector
side view
Module-Sentry Key
Remote Entry
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 17
Parking Light Vehicle Wiring Reference Chart (Type 5)
Headlight switch,
black 12-pin plug
Vehicle
Years Wire
(+) / (-) Location
Chrysler
Pacifica
2004-08 Brown/White (-1K) MUX Headlight switch, black 12-pin plug, pin 6
Town & Country 2004-07 White/Orange
(+) Driver kick panel
1 2 3 4 5 6
7 8 9 10 11 12
Dodge
Caravan
2004-07 White/Orange
(+) Driver kick panel
(+) Driver kick panel
Grand Caravan 2004-07 White/Orange
(+) Parking Lights
(MUX) Parking Lights
1KΩ
To vehicle’s
(+) Parking Lights
To vehicle’s
(MUX) Parking Lights
85
85
86
86
87
87
2: Green/Black: (-) Parking Lights
2: Green/Black: (-) Parking Lights
87a
87a
OR
30
30
+12v
+12v
Fuse 15A
Positive (+)
MUX
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 18
Module Programming for Installation Types 1 to 4 (WITH Factory Keyless)
Refer to the LED Diagnostics section on page 23 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper
communication protocol is enabled on DBALL using XpressVIP. This selection is done by:
2. Selecting the make, model and year of the vehicle.
3. On the search result page, click on the Flash it button.
4. The flash page will then be displayed listing the D2D type settings. Make your selection and flash the module.
To use DBALL with an:
§ RF Kit and XL202, D2D (RFTD) must be selected.
§ SmartStart (Revision B), D2D (SmartStart) must be selected.
Warning against resetting the DBALL module before executing the programming sequence!
A reset will erase all the settings configured on the module using the web tool (see the above instructions). Therefore, if you reset
before executing the programming sequence, you will HAVE to re-flash the module in order to re-configure the desired options.
DBALL Module Programming
D2D
10-pin
Connect the SmartStart or XL202 unit into the D2D port of the DBALL prior to
connecting the power.
1
D2D
10-pin
14-pin
12-pin
Connect the 10-pin, 12-pin and 14-pin
harnesses to DBALL, then wait until the
LED turns ON solid red or flashes orange.
or
&
2
3
3rd
1st
2nd
Flashes
Solid
Key Ignition
Push-to-Start (PTS) Ignition
3
Insert the key into the ignition barrel and turn it
to the ON position.
Important: Do NOT press the brake pedal.
Press the Push-to-Start (PTS) button twice to
turn the ignition ON.
It is important to wait for the LED to start flashing
green. Refer to the LED Diagnostics section on
page 23 for troubleshooting if the LED does not
flash green within 15 seconds.
Do NOT
ENGINE
START
STOP
press the
PUSH
2X
brake pedal
It is important to wait for the LED to start flashing
green. Refer to the LED Diagnostics section on
page 23 for troubleshooting if the LED does not
flash green within 15 seconds.
KeyIN
&
START
Flashes
Flashes
Turn the key to the OFF
position and remove it
from the ignition barrel.
Press the Push-to-Start
(PTS) button once more
to turn the ignition OFF.
KeyOUT
ENGINE
START
STOP
PUSH
1X
4
5
4
START
Press LOCK or UNLOCK on the
factory transmitter. The LED turns
ON solid green OR orange for 3 seconds
and then turns off.
or
&
or
&
Solid
Solid
Off
Important! If connected to a SmartStart, please ensure that its Gray wire is connected to a ground source or the D2D
communication between the two (2) modules will NOT work.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 19
Module Programming for Installation Types 1 to 4 (WITHOUT Factory Keyless)
Refer to the LED Diagnostics section on page 23 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper
communication protocol is enabled on DBALL using XpressVIP. This selection is done by:
2. Selecting the make, model and year of the vehicle.
3. On the search result page, click on the Flash it button.
4. The flash page will then be displayed listing the D2D type settings. Make your selection and flash the module.
To use DBALL with an:
§ RF Kit and XL202, D2D (RFTD) must be selected.
§ SmartStart (Revision B), D2D (SmartStart) must be selected.
Warning against resetting the DBALL module before executing the programming sequence!
A reset will erase all the settings configured on the module using the web tool (see the above instructions). Therefore, if you reset
before executing the programming sequence, you will HAVE to re-flash the module in order to re-configure the desired options.
DBALL Module Programming
D2D
10-pin
Connect the SmartStart or XL202 unit into the D2D port of the DBALL prior to
connecting the power.
1
2
Connect the 10-pin, 12-pin and 14-pin
harnesses to DBALL, then wait until the
LED turns ON solid red or flashes orange.
D2D
10-pin
14-pin
12-pin
or
&
3rd
1st
2nd
Flashes
Solid
Insert the key into the ignition barrel and turn it to the ON position.
It is important to wait for the LED to start flashing green.*
KeyIN
&
3
START
* Refer to the LED Diagnostics section on page 23 for troubleshooting
if the LED does not flash green within 15 seconds.
Flashes
Press and hold the Programming Button. The LED
turns ON solid green OR orange for 3 seconds and
then turns OFF. Release the Programming button.
or
&
&
&
4
5
Press & Hold
Solid
Solid
Off
Release
KeyOUT
Turn the key to the OFF position and remove it from the ignition barrel.
START
Important! If connected to a SmartStart, please ensure that its Gray wire is connected to a ground source or the D2D
communication between the two (2) modules will NOT work.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 20
Module Programming for Installation Type 5
Refer to the LED Diagnostics section on page 23 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper
communication protocol is enabled on DBALL using XpressVIP. This selection is done by:
2. Selecting the make, model and year of the vehicle.
3. On the search result page, click on the Flash it button.
4. The flash page will then be displayed listing the D2D type settings. Make your selection and flash the module.
To use DBALL with an:
§ RF Kit and XL202, D2D (RFTD) must be selected.
§ SmartStart (Revision B), D2D (SmartStart) must be selected.
Warning against resetting the DBALL module before executing the programming sequence!
A reset will erase all the settings configured on the module using the web tool (see the above instructions). Therefore, if you reset
before executing the programming sequence, you will HAVE to re-flash the module in order to re-configure the desired options.
DBALL Module Programming
D2D
10-pin
Connect the SmartStart or XL202 unit into the D2D port of the DBALL prior to
connecting the power.
1
2
3
D2D
10-pin
14-pin
12-pin
Connect the 10-pin, 12-pin and 14-pin harnesses to
DBALL, then wait until the LED turns ON solid red.
&
3rd
1st
2nd
Solid
KeyIN
Insert the key into the ignition barrel without turning it and wait for
the LED to flash orange.
&
START
Flashes
Insert the key into the ignition barrel and turn it to the ON
position. The LED will continue to flash orange. It will then
turn ON solid green OR orange for 3 seconds, before
turning OFF.
KeyIN
or
&
START
Solid
Solid
4
5
Refer to the LED Diagnostics section on page 23 for
troubleshooting if the LED does not turn ON solid green OR
orange within 15 seconds.
&
Off
KeyOUT
When the green LED turns OFF, turn the key to the OFF position
and remove it from the ignition barrel.
&
START
Off
Important! If connected to a SmartStart, please ensure that its Gray wire is connected to a ground source or the D2D
communication between the two (2) modules will NOT work.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 21
DBALL Module Reset
Refer to the LED Diagnostics section on page 23 for more information and for troubleshooting purposes.
Warning against resetting the DBALL module before executing the programming sequence!
A reset will erase all the settings configured on the module using the web tool (see the above instructions). Therefore, if
you reset before executing the programming sequence, you will HAVE to re-flash the module in order to re-configure the
desired options.
14-pin
If using in D2D: Connect the 10-pin, 12-pin & 14-pin
harnesses to the module. Press & hold the programming
button, then connect the 4-pin D2D harness.
D2D
10-pin
12-pin
3rd
1a
5th
2nd
1st
4th
14-pin
12-pin
If using in W2W: Connect the 10-pin & 12-pin harnesses to
the module. Press & hold the programming button, then
connect the 14-pin harness to the module.
D2D
10-pin
4th
1b
2
2nd
1st
3rd
Wait until the LED turns ON orange then release the
Programming button. The LED turns ON red.
&
&
Solid Orange
Release
Solid Red
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 22
Feature and Option List
It is recommended to configure all features and options listed below on the web when the module is being flashed;
however, a manual configuration is possible using the information found on this page.
Features
Operation
Option
** Important
RF Output Type**
No RF Output*
The RF Output Type function must be
set to RFTD Output to enable the Remote
Start Ready (RSR) mode.
Activate this feature whenever an external
RFTD module is used (i.e. Directed
SmartStartTM, XL201 or XL202).
1
RFTD Output
It will automatically be configured on the web
when flashed with the selected D2D_TYPE
D2D (RFTD) or D2D (SmartStart).
No Option
Trunk*
2
3
Trunk
Aux1
Aux2
Right Sliding Door
Left Sliding Door
No Option
Any module reset will reset to default
option.
Trunk
Passenger Sliding Door*
Driver Sliding Door
No Option
Trunk
4
Passenger Sliding Door
Driver Sliding Door*
* Default option
Note: Features 2, 3 and 4 are programmable triggers.
Feature Programming
Programming
Button
To enter feature programming routine
-
Turn the ignition ON, then OFF.
Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.
-
-
The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will
repeat until a new command is entered.
Changing feature options
-
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green
slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
-
Accessing another feature
-
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
-
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or
option.
Once a feature is programmed
-
Other features can be programmed.
The feature programming can be exited.
-
Exiting feature programming
-
No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.
OR
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the
-
end of the programming sequence.
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 23
LED Diagnostics and Troubleshooting
LED Status
Module Programming
Description
Troubleshooting
Off
Off
Module has no power.
The bus type cannot be detected.
Check the power connections.
Make sure the connections to the data bus are correct
and insert the key in the ignition switch.
Solid
Solid red
The vehicle type cannot be
detected.
Insert the key in the ignition switch and turn to the ON
position. You may need to wait up to 10 seconds.
Flashes
Flashes orange
Remove the key from the ignition switch and press a
keyless button.
Waiting for keyless.
Flashes
Flashes green
The Programming button was held A reset occured. Release the button. The LED should
while powering up.
turn solid red.
Module was successfully
programmed or is already
programmed.
Solid green for
Solid
x3 secs
Normal operation.
3 seconds
Types 1-5: Module was
successfully programmed without
diagnostics.
Solid orange for
Solid
x3 secs
Normal operation.
3 seconds
Active Ground While Running
Make sure the module was programmed, i.e. the D2D
Off
Off
Ground While Running (status) off. harness is properly connected or the Ground While
Running (status) wire is connected.
Flashes
Flashes green
Ground While Running (status) on. Normal operation.
Inactive Ground While Running
If it does not flash, the bypass module did not receive
the signal. Verify the connections between the bypass
and the remote starter module.
Flashes green
Flashes
1x
Lock function has been executed.
once (1)
If it does not flash, the bypass module did not receive
the signal. Verify the connections between the bypass
and the remote starter module.
Flashes green
twice (2)
Unlock function has been
executed.
Flashes
2x
If it does not flash, the bypass module did not receive
the signal. Verify the connections between the bypass
and the remote starter module.
Flashes green
three (3) times
Trunk release function has been
executed.
Flashes
3x
If it does not flash, the bypass module did not receive
the signal. Verify the connections between the bypass
and the remote starter module.
Flashes green
four (4) times
AUX1 or AUX2 function has been
executed.
Flashes
4x
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 24
Optional RF Kits
Note: RF kits are sold SEPARATELY. Request an order from Directed using the part numbers listed below.
9211VL
Viper 1-way Responder ONE - Plug & Play RF kit with XL202.
UPC: 093207 08488 1
Also available as:
§ Python: 9211PL
§ Clifford: 9211XL
9153VL
9251VL
9752VL
Viper 1-way - Plug & Play RF kit with XL202.
UPC: 093207 05660 4
Also available as:
§ Python: 9153PL
§ Clifford: 9153XL
Viper 2-way Responder LE - Plug & Play RF kit with XL202.
UPC: 093207 08489 8
Also available as:
§ Python: 9251PL
§ Clifford: 9251XL
Viper 2-way LC3 - Plug & Play RF kit with XL202.
UPC: 093207 08490 4
Also available as:
§ Python: 9752PL
§ Clifford: 9752XL
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 25
Optional RF Kits
Note: RF kits are sold SEPARATELY. Request an order from Directed using the part numbers listed below.
AF-RFK636
AF-RFK5225
Astrostart 2-way LED
Receiver kit with up to
1,500’ of range.
Astrostart 2-way LCD
Receiver kit offering
XRTTM technology with up
to 5,000’ of range.
UPC: 093207 08752 3
UPC: 093207 08753 0
AS-RFK1700
AS-RFK2300
Autostart 1-way Receiver
kit with up to 3,000’ of
range.
Autostart 2-way LED
Receiver kit offering
HDRTM technology with up
to 3,000’ of range.
UPC: 093207 08738 7
UPC: 093207 08739 4
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 26
Using your DBALL-CHRYSLER RSR
Press button to
Press the button to remote start the vehicle.
remote start*
1
* Your remote starter model may differ from the one shown in the illustration.
Enter vehicle
with the Smart
Key in hand
Enter the vehicle, while making sure the key is inside with you.
2
Important: Do NOT press the brake pedal.
Do NOT
ENGINE
START
STOP
press the
brake pedal
PUSH
2X
Press the Push-to-Start (PTS) button twice to turn
the ignition ON.
3
You can now put the car in gear and drive off.
Ready to
drive off
4
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform: DBALL
Firmware: CHRYSLER Remote Start Ready Installation
Rev.: 20120307
Page 27
Limited One Year Consumer Warranty
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed
Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the
security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material
under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer;
and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the
following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete
product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its
intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or
other causes not arising out of defect in materials or construction.
TOTHE MAXIMUM EXTENTALLOWED BYLAW, EXCEPTAS STATEDABOVE,ALLWARRANTIES, INCLUDING BUT NOT
LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSEAND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY,ARE EXPRESSLY
EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT
ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND
HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR
INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIASTATE LAWSANDAPPLICABLE
FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM
AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE
OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT
LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS
OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITYAND THE LIKE. NOTWITHSTANDING THE
ABOVE, THE MANUFACTURER DOES OFFERALIMITED WARRANTYTO REPLACE OR
REPAIRATDIRECTED’S OPTIONTHE PARTAS DESCRIBEDABOVE.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State
to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or
obligation in connection with this Part.
920-0007 2009-09
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select
vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no
circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any
consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor
will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data
bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this
product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes
any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876
B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;
7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:
2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European
Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Additional information can be found at:
© 2012 Directed. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|