X10 Wireless Technology Home Security System SC1200 User Manual

Supervised Security System

Model SC1200

Owner’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Read This First

Contents

This equipment generates and uses radio

frequency energy, and if not installed and

used properly, that is, in strict accordance

with the manufacturers instructions, may

cause interference to radio and television

reception. It has been type tested and

found to comply with the limits for remote

control security devices in accordance

with the speciﬁcations in Sub-Parts B

and C of Part 15 of FCC Rules, which

are designed to provide reasonable

protection against such interference in

a residential installation. However, there

is no guarantee that interference will not

occur in a particular installation. If this

equipment does cause interference to

radio or television reception, which can be

determined by unplugging the equipment,

try to correct the interference by one or

more of the following measures.

This equipment complies with Part 68

of the FCC rules and the requirements

adopted by the ACTA. On the bottom of

this equipment is a label that contains,

among other information, a product

identiﬁer US: B4SAL11B-SC12A. If

requested, this number must be provided

to the telephone company.

Introduction......................................................................................................4

Installation........................................................................................................5

Locating Security System components ........................................................5

Attaching the cables .....................................................................................6

Fitting the backup batteries ..........................................................................7

Wall mounting...............................................................................................7

Overview...........................................................................................................8

Registering Remotes..................................................................................12

Registering Door/Window Sensors.............................................................13

Removing Door/Window Sensors...............................................................14

Installing Door/Window Sensors.................................................................15

Registering Motion Detectors .....................................................................16

Removing Motion Detectors .......................................................................17

Installing Motion Detectors .........................................................................18

Setting the Clock ........................................................................................20

Setting the Phone Numbers .......................................................................21

Setting the Outgoing Message ...................................................................22

Setting the PIN ...........................................................................................24

Clearing the Memory ..................................................................................25

Setting the Options.....................................................................................26

Setting the Delays ......................................................................................27

Setting the Timers ......................................................................................28

Using the System ..........................................................................................32

Arming and Disarming................................................................................32

Problem zones............................................................................................33

When there’s an alarm ...............................................................................34

Controlling Lights and Appliances..............................................................35

Setting up Optional Lamp Modules .............................................................36

Operation from an Outside Telephone........................................................37

Replacing Batteries.......................................................................................38

Troubleshooting ............................................................................................38

Note: The security functions of this system

have not been tested by Underwriters

Laboratories.

•

Reorient the antenna of the radio/TV

experiencing the interference.

•

Relocate the Console with respect to

the

radio/TV.

•

Move the Console away from the radio/

TV.

Plug the Console into an outlet on a

different electrical circuit from the radio/

TV experiencing the interference.

If necessary, contact www.x10.com for

additional suggestions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Installation

The X10 Supervised Security System Console with automatic dialer calls neighbors or

friends in the event of a break in. Battery powered Wireless Door/Window Sensors trigger

the alarm when a door or window is opened. A battery powered RF Motion Detector

protects an indoor area. The Keychain Remote Control is used for arming and disarming

the system. It can also turn lights on and off (requires X10 Modules). All sensors and

remotes incorporate random digital security coding.

Locating Security System components

Locating the Security Console

The system may be conﬁgured with any combination of the following items:

•

Up to 16 Keychain Security Remotes with arm/disarm and panic functions, and buttons

to control security lights in and around the home.

Dining Room

Hallway

•

Up to 30* magnetic switch operated Wireless Door/Window Sensors.

Up to 30* Wireless Motion Detectors.

Living Room

Additional X10 Home Automation modules such as plug-in Lamp and Appliance

Modules and wired-in replacement Wall Switch Modules can be added to the system to

ﬂash lights on and off when the alarm trips.

*Note: Door/Window Sensors and Motion Detectors may be added in any

combination up to a total of 30, e.g., 15 Door/Window Sensors and 15 Motion

Detectors, or any combination up to a total of 30. There are also 2 hard wired inputs,

which are zones 31 and 32.

Kitchen

Study

Choose a location for the Security Console which is as central as possible in the house,

while providing access to a modular telephone jack and an AC outlet. The Console may be

placed on a shelf or table, or may be wall mounted.

Locating Door/Window Sensors and Motion Detectors

Plan the location of the Door/Window Sensors and Motion Detectors so that the RF path

which runs in a straight line from sensor to Console is not obstructed by large metal objects

such as a refrigerators or freezers, and passes through as few walls as possible.

Door/Window Sensors may be hidden behind drapes for a more discreet installation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Fitting the backup batteries

Security Console

Attaching cables

Open the battery compartment cover at the top right hand side of the Console and install 4

AA alkaline batteries (not supplied). It is not necessary to disconnect power to the Console

when ﬁtting or replacing batteries.

A telephone cord terminated at each end with an RJ11 connector is provided for telephone

connection. If possible, the Console should be connected to its own telephone line to

ensure that the line cannot be busy when the Console attempts to dial out. For applications

where this is not practical, the Console may also share a line with an existing telephone

using a ‘T’ adapter (supplied).

Note: The Security Console is not designed to operate with an RJ31X type telephone

connection.

Attach the power

supply’s cord here.

Turns on if

batteries are

low or not

installed.

Attach the phone

cord here.

Hard Wired Inputs.

Tamper Switch

Mounting the Console

The Security Console is designed to be installed freestanding on a table top or shelf. Or it

can be wall mounted using the two slotted holes on the back of the Console.

Open the lid on the Console and attach

the power supply’s cord to the connector

labeled power supply (see above). Plug

the power supply into any convenient

(unswitched) AC outlet.

NOTE: you must use the power supply that

came with the Security System. The power

supply contains circuitry required to control

X10 Modules, so you CANNOT replace it

with a regular 8V DC power supply.

If you don’t want to wall mount the console, you can insert the included rubber plugs into

the two slotted mounting holes so as to tilt the console slightly forward for better viewing of

the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Console setup Overview

Console setup Overview, cont.

After you’ve followed the steps on page 6 and 7 and connected power to the Console, the

display shows the time of day at the left of the bottom line, with HOME CONTROL in the

top line. See below:

HOME CONTROL

12:00 am

All features (except Home Control) require access to the Menu mode. To do this, press

either of the Menu up/down buttons (under the lid to the bottom right of the display). The

display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

ENTER PIN

12:00 am

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

Console keyboard buttons are as follows:

****

12:00 am

0-9 Used for all number entries.

On Used to send an X10 On message or to enter am in a time.

Off Used to send an X10 Off message or to enter pm in a time.

Menu up Used to initially enter the menu and then to move up through the items.

When you enter the PIN the display shows the First Level of the menu at step 1, below.

See next page.

Menu down Used to initially enter the menu and then to move down through the

items.

1. INSTALL

Clear Used to clear entries, back up through the menu levels, and to bypass

problem Door/Window Sensors or Motion Detectors.

Enter Used to terminate an entry.

Arm Home Used to arm the console in the Home mode.

Arm Away Used to arm the console in the Away mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

First Menu Level

After pressing a menu up/down button and entering the PIN, the First level menu is

displayed, as shown below:

Sub-menus

Once you’ve arrived at your desired ﬁrst level menu and pressed OK, you can select the

sub-menus under that menu item. Alternatively you can go directly to the sub-menu item

by pressing the appropriate number button.

Phone Numbers Sub-menu

1. INSTALL

Enter number up to 16 digits. Off/pm gives a pause.

PHONE 1

PHONE 2

PHONE 3

PHONE 4

PHONE 5

PHONE 6

To select a menu option, press the up or down Menu button repeatedly to step through the

menu items 1 through 9 below (or you can press the number buttons 1 thru 9 on the control

panel (under the lid to the bottom right of the display) to go directly to that menu item.

Once you arrive at the menu item you desire, press OK to select it.

1. INSTALL

2. SET CLOCK

Allows installation/removal of sensors, and/or remotes.

Enter time followed by am or pm.

Delays Sub-menu

3. PHONE NUMS Store up to six (16 digit) phone numbers.

All times are entered in seconds, up to 99.

ENTRY DELAY

EXIT DELAY

DIAL DELAY

ANSWER DELAY

4. MESSAGE

1. RECORD (This is your own alarm message)

2. REPLAY (Replays your message).

Enter new 4 digit PIN.

5. NEW PIN

6. MEMORY

CLEAR

Clear all Sensors, Remotes, Timers, or Master Clear.

7. OPTIONS

8. DELAYS

9. SET TIMER

Set Chime On/Off, Siren On/Off, Set Housecode or Light Code.

Set Exit, Entry, Dial, and Answer Delays.

Enter unit code, then On and Off time, then Daily, Once or Random.

Options Sub-menu

CHIME

SIREN

1. CHIME ON

2. CHIME OFF (No chimes when doors/windows are opened)

1. SIREN ON

2. SIREN OFF (Silent Alarm)

Chosen by Menu up/down buttons

To leave the ﬁrst level menu press the Clear button. If you are entering numbers (for

the time, etc.), Clear will clear all numbers entered. Otherwise Clear gives the option of

leaving the menu completely and going back to the HOME CONTROL mode, or staying in

HOUSECODE

LIGHTCODE

the INSTALL mode.

Direct menu

access numbers

Menu buttons

OK button

Memory Clear Sub-menu

CLEAR ALL

SENSORS

CLEAR ALL

REMOTES

CLEAR ALL

TIMERS

MASTER

RESET

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Initializing Keychain Remotes

Initializing Door/Window Sensors

Press and hold the ARM button on the Keychain remote for 3-4 seconds

and then release it. This initializes the remote and picks a random code

that is used when it is registered with the Console. Note, if the Keychain

remote you purchased is different from shown here, refer to the

installation instructions that came with it.

Remove the screw from the front of the Door/Window Sensor and install

2 AAA alkaline batteries inside. Observe polarity.

Set switch to MAX (left) for doors, or MIN (right) for windows.

Press and hold the button inside the Sensor for 3-4 seconds and then

release it. This initializes the Sensor and picks a random code that is

used when it is registered with the Console. Replace cover and place

the magnet next to the Sensor (with the arrows aligned).

See pages 14 and 15 if you want to use an additional magnetic contact

switch. Note, if the Sensors you purchased are different from shown

here, refer to the installation instructions that came with them.

Registering the Keychain Remote with the Console

Press either of the Menu up/down buttons (under the lid to the bottom right of the display).

The display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

ENTER PIN

12:00 am

Registering Door/Window Sensors with the Console

Press either of the Menu up/down buttons (under the lid to the right of the display). The

display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

ENTER PIN

12:00 am

****

12:00 am

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level.

When you see INSTALL on the display, press OK. The display then looks like this:

****

12:00 am

1. INSTALL

ZONE

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

Now simply press any button on the Keychain remote. The Console acknowledges that it

has been registered by beeping and displaying RMOT 1 SET, RMOT 2 SET, etc., as you

install more remotes.

1. INSTALL

Repeat this for any other Keychain Remotes you want to register.

Press OK and the display looks like this:

Press Clear to back out of the menu. You are asked to conﬁrm, 1. YES, 2 NO. Pressing

1 takes you back to the HOME CONTROL screen. Pressing 2 takes you up one level of

menu.

1. INSTALL

ZONE

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Now move the magnet away from the Door/Window Sensor. The Console acknowledges

that it has been registered with a chime and by displaying ZONE 1 SET.

Installing the Door/Window Sensors

Note, if the Sensors you purchased are

different from shown here, refer to the

installation instructions that came with them.

Repeat this for any other Door/Window Sensors you want to register. The display

increments to ZONE 2 SET, etc., as you install more Door Window Sensors. If you

connected a second magnetic switch to the contacts on the sensor (as shown on the next

page) move its magnet away to install the second magnetic switch as a separate zone.

Ideal location

Two doors or windows

(requires accessory

magnetic switch pair)

If desired, you can specify what zone you want the Door Window Sensor to be registered

into. Just press the number of the zone you want on the Console’s keypad, before you

Press Clear to back out of the menu. After a short delay the display reverts to showing

HOME CONTROL on the top line and the time of day on the bottom line.

Removing Door/ Window Sensors

Follow the steps above to install a sensor. Then when the display shows:

Sliding window

Remove shorting link

before installing hard

wired magnetic contacts.

Note when you add a magnetic switch to a

sensor you can register it with the console

as its own zone, e.g., the sensor itself can

be zone 1 and the extra magnet zone 2.

See previous page.

1. INSTALL

ZONE

Press the number of the zone you desire (just as if you were going to register the Door/

Window Sensor into that zone) but instead of registering the Door/Window Sensor, press

CLEAR on the Console’s keypad. The display asks you to conﬁrm the deletion:

• Attach the Door/Window Sensor to the wall using the mounting screws provided.

• Fit the Door/Window Sensor as high as possible at the top of the door/window.

• Make sure the arrows on the magnetic and the Door/Window Sensor are facing each

other and that they separate cleanly when the door or window is opened.

CLEAR ZONE

1. YES 2. NO

• To protect two doors or windows close to each other, use the Door/Window Sensor with

an additional set of magnetic switch contacts as shown in the diagrams above.

Pressing 1 on the Console’s keypad changes the display to:

• Set the DELAY slide switch (inside the Sensor) to MIN to always trigger the alarm

instantly (for windows), or to MAX to trigger the alarm after a preset entry delay when the

system is armed in the AWAY mode (for doors).

1. INSTALL

ZONE 13 OUT

The numbers 1 – 32 in the display refer to up to 32 “zones.” These represent up to 30

Door/Window Sensors and/or Motion Detectors you install, plus the 2 hard wired zones.

The numbers show open zones, problem zones and bypassed zones by being displayed

as steady on (door or window open), slow ﬂash (there’s a problem with that zone) or fast

ﬂash (that zone has been bypassed). Attempting to arm with an open or problem zone

makes the Console beep continuously and it will display in words on the display what the

cause is, but only for one zone at a time. Bypassing that zone (by pressing the Clear

button) moves on to the next problem zone, if there is one.

Where 13 is the zone you selected. Pressing 2 instead takes you back to the INSTALL

ZONE screen.

Press Clear to back out of the menu. You are asked to conﬁrm, 1. YES, 2 NO. Pressing

1 takes you back to the HOME CONTROL screen. Pressing 2 takes you up one level of

menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Now simply press the TEST button on the back of the Motion Detector (or turn the unit

over so that it sees motion). The Console will acknowledge that it has been registered by

displaying (for example) ZONE 3 SET.

Initializing Motion Detectors

Remove the cover on the front of the Motion Detector and install 2

AAA alkaline batteries in the compartment. Replace the cover.

Press and hold the TEST button on the back of the Motion Detector

for 3-4 seconds and then release it. This initializes the Motion

Detector and picks a random code that is used when it is registered

with the Console. Place the unit face down, so that it won’t see any

motion during the registering process below. Note, if the Motion

Detectors you purchased are different from shown here, refer to

the installation instructions that came with them.

Repeat this for any other Motion Detectors you want to register. The display increments to

ZONE 4 SET, etc., as you install more Motion Detectors.

If desired, you can specify what zone you want the Motion Detector to be installed into.

Just press the number of the zone you want on the Console’s keypad, before you press the

TEST button on the back of the Motion Detector.

Press Clear to back out of the menu. You are asked to conﬁrm, 1. YES, 2 NO. Pressing

1 takes you back to the HOME CONTROL screen. Pressing 2 take you up one level of

menu.

Registering the Motion Detector with the Console

Press either of the Menu up/down buttons (under the lid to the right of the display). The

display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

Removing Motion Detectors

Follow the steps above to install a Motion Detector. When the display shows:

ENTER PIN

12:00 am

1. INSTALL

ZONE

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

Press the number of the zone you desire (just as if you were going to register the Motion

Detector into that zone) but instead of pressing the TEST button on the Motion Detector

(to register it) press CLEAR on the Console’s keypad. The display ask you to conﬁrm the

deletion:

****

12:00 am

CLEAR ZONE

1. YES 2. NO

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

Pressing 1 on the Console’s keypad changes the display to:

1. INSTALL

ZONE 13 OUT

Press OK and the display looks like this:

Where 13 is the zone you selected. Pressing 2 instead takes you back to the INSTALL

ZONE screen.

1. INSTALL

ZONE

Press Clear to back out of the menu. You are asked to conﬁrm, 1. YES, 2 NO. Pressing

1 takes you back to the HOME CONTROL screen. Pressing 2 takes you up one level of

menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Installing the Motion Detector

Hard-Wired Inputs

You can also connect two hard-wired magnetic contact switches to the console.

• Attach the Motion Detector to a wall at a height of 5 to 6 ft. using the mounting bracket

and screws provided.

• Point the Motion Detector so that it looks slightly downwards.

• Set the slide switch (on the back) to position 1 for instant triggering for maximum

sensitivity or position 2 to trigger only after two movements have been sensed.

90°

MOTION DETECTOR

These will be zones 31 and 32.

5-6ft

You can install a total of 30 additional zones, which can be a combination of Door/Window

Sensors and Motion Detectors. So, for example, you could have 15 Door/Window Sensors,

15 Motion Detectors, and 2 hard-wired zones. The hard wired zones are treated as delayed

zones (i.e. they have exit and entry delays if you arm the system in the Away mode).

30-40ft

Tamper switch (under lid). Note,

some models do not have a

tamper switch. See note at top of

page 16.

Magnetic Switch

Contacts sold

separately

Remove shorting link

before installing hard

wired magnetic contacts.

Testing the Motion Detector

• Set the slide switch on the Motion Detector to position 1.

• Press and hold the TEST button for about a second (until

the LED ﬂashes twice) and then release it.

• Wait 20 seconds for the Motion Detector to settle.

• Walk in front of the Motion Detector. The indicator LED

lights each time it senses movement. Check the coverage

area and reposition the sensor as required.

• Press the TEST button to return to normal operating

mode.

Note: The Motion Detector will automatically return to

normal operating mode after about 2 minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Setting the Clock

Setting the phone numbers

Press either of the Menu up/down buttons (under the lid to the bottom right of the display).

The display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

ENTER PIN

12:00 am

ENTER PIN

12:00 am

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

****

12:00 am

****

12:00 am

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

1. INSTALL

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

Press an up or down menu button until you reach the PHONE NUMS menu, and then

press OK to go to the screen below (or press 3 to go into the PHONE NUMS menu ):

1. INSTALL

3. PHONE NUMS

Press an up or down menu button until you reach the SET CLOCK menu, and then press

OK (or press 2 to go directly to the screen below):

Press an up or down Menu button to select the desired sub-menu:

PHONE 1

PHONE 2

PHONE 3

PHONE 4

2. SET CLOCK

4:00 pm

PHONE 5

PHONE 6

Press OK at the desired number (1-6). The display shows SET PH1, SET PH2, etc. Enter

the phone number, up to 16 digits. off/pm gives a pause. Press OK. This takes you to the

next phone number to be stored.

Enter the time by pressing the digits on the Console’s keyboard. Then press am or pm.

Then press OK.

Press Clear to back out of the menu. If you press Clear while entering numbers, before

you’ve ﬁnished setting the phone number, it clears the numbers. If you press Clear after

you ﬁnished entering the phone number and pressed OK, you are asked to conﬁrm, 1.

YES, 2 NO. Pressing 1 takes you back to the HOME CONTROL screen. Pressing 2 stays

in INSTALL mode.

Press Clear to back out of the menu. If you press Clear while entering numbers, before

you’re ﬁnished setting the clock, it clears the numbers. If you press Clear after you’ve set

the time and pressed OK, you are asked to conﬁrm, 1. YES, 2 NO. Pressing 1 takes you

back to the HOME CONTROL screen. Pressing 2 stays in INSTALL mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Press 1 for RECORD , then press OK. The display shows:

Recording your outgoing phone message

Press either of the Menu up/down buttons (under the lid to the bottom right of the display).

The display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

PLEASE WAIT

ENTER PIN

12:00 am

Then:

SPEAK NOW

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

Clearly speak your message into the Console’s microphone (up to 12 seconds max.).

A typical message could be: “There’s an alarm in progress at (your address), at the end of

this message please press any button on your touch-tone phone to listen in.” After you’ve

ﬁnished speaking (12 seconds max), wait for the display shown below:

****

12:00 am

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

1. RECORD

2. REPLAY

1. INSTALL

Now press 2 for REPLAY the display shows:

PLEASE WAIT

Press an up or down menu button until you reach the MESSAGE menu, and then press

OK to go to the screen below (or press 4 to go into the MESSAGE menu ):

It then plays back your recorded message. Wait for the display shown below:

4. MESSAGE

1. RECORD

2. REPLAY

Press 1 or 2 to select one of the options below:

1. RECORD

2. REPLAY

Press Clear to back out of the menu. You are asked to conﬁrm, 1. YES, 2 NO. Pressing 1

takes you back to the HOME CONTROL screen. Pressing 2 stays in the INSTALL mode.

Note: you cannot record messages remotely via telephone.

1. RECORD (This is your own alarm message).

2. REPLAY (This replays a previously recorded message).

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Changing your Personal Identiﬁcation Number (PIN)

Clearing the memory

Press either of the Menu up/down buttons (under the lid to the bottom right of the display).

The display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

ENTER PIN

12:00 am

ENTER PIN

12:00 am

The default PIN is 0000, so press 0000 on the keypad (under the lid to the bottom right of

the display). This clears the top line and shows * for each number entered.

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

****

12:00 am

****

12:00 am

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

1. INSTALL

Press an up or down menu button until you reach the MEMORY CLEAR menu, and then

press OK to go to the screen below (or press 6 to go into the MEMORY CLEAR menu ):

Press an up or down menu button until you reach the NEW PIN menu, and then press OK

(or press 5 to go directly to the screen below):

6. MEMORY

CLEAR

5. NEW PIN

Press an up or down Menu button to select the desired sub-menu.

Enter your new PIN (4 digits). Press OK.

CLEAR ALL SENSORS

CLEAR ALL REMOTES

CLEAR ALL TIMERS

MASTER RESET

Note, choose a PIN that you are not likely to forget (a birthday, for example). If you forget

your PIN you will not be able use the system. If you do forget your PIN contact www.x10.

com to ﬁnd out how to reset your system.

Press Clear to back out of the menu. If you press Clear while entering numbers, before

you’re ﬁnished setting the new PIN, it clears the numbers. If you press Clear after you’ve

set the new PIN and pressed OK, you are asked to conﬁrm, 1. YES, 2 NO. Pressing 1

takes you back to the HOME CONTROL screen. Pressing 2 stays in INSTALL mode.

Select the desired sub-menu item and then press OK. Press Clear to back out of the

menu. You are asked to conﬁrm, 1. YES, 2 NO. Pressing 1 takes you back to the HOME

CONTROL screen. Pressing 2 stays in the MEMORY CLEAR menu. Note, selecting 4.

MASTER RESET immediately takes you back to the HOME CONTROL screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Setting Options

Setting Delays

Press either of the Menu up/down buttons (under the lid to the bottom right of the display).

The display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

ENTER PIN

12:00 am

ENTER PIN

12:00 am

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

****

12:00 am

****

12:00 am

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

1. INSTALL

Press an up or down menu button until you reach the DELAYS menu, and then press OK

to go to the screen below (or press 8 to go into the DELAYS menu ):

Press an up or down menu button until you reach the OPTIONS menu, and then press OK

to go to the screen below (or press 7 to go into the OPTIONS menu ):

8. DELAYS

7. OPTIONS

Press an up or down Menu button to select the desired sub-menu:

Press the up or down Menu button to select the desired sub-menu:

CHIME

SIREN

1. CHIME ON

ENTRY DELAY

EXIT DELAY

DIAL DELAY

(Default 30 seconds)

(Default 60 seconds)

(Default 5 seconds)

(Default 30 seconds)

2. CHIME OFF (No chimes when doors/windows are opened)

1. SIREN ON

2. SIREN OFF (Silent Alarm)

(Chosen by Menu up/down buttons)

ANSWER DELAY

HOUSECODE

LIGHTCODE

Select the desired sub-menu item and then press OK. Then enter the desired delay time in

seconds up to 99. Press OK.

Select the desired sub-menu item and then press OK. Press 1 or 2 in CHIME and SIREN

sub-menus. Select the desired Housecode letter, or desired Security Light Code, using

the up/down buttons. Press OK. Press Clear to back out of the menu. You are asked

to conﬁrm, 1. YES, 2 NO. Pressing 1 takes you back to the HOME CONTROL screen.

Pressing 2 stays in INSTALL mode.

Press Clear to back out of the menu. You are asked to conﬁrm, 1. YES, 2 NO. Pressing

1 takes you back to the HOME CONTROL screen. Pressing 2 stays in INSTALL mode.

Pressing Clear while entering a number (for a delay time) just clears the numbers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

To enter a new timer you must be on the NEW TIMER screen. Then press OK. The display

shows UNIT NUMBER on the top line. Using the number keys, enter a valid number (1-16)

and press OK.

Setting Timers

Press either of the Menu up/down buttons (under the lid to the bottom right of the display).

The display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

9. UNIT NUMBER

ENTER PIN

12:00 am

Say for example you enter 12. The top line displays TIMER 12 ON. The bottom line

displays a colon, :

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

9. TIMER 12 ON

Enter your desired ON time with the number keys followed by am or pm in the format

shown below, (or just press OK if you don’t want to set an ON time). Press Clear if you

enter a wrong time.

****

12:00 am

9. TIMER 12 ON

12:34am

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

Then press OK. The top line displays TIMER 12 OFF. The bottom line displays a colon, :

1. INSTALL

9. TIMER 12 OFF

Press an up or down menu button until you reach the SET TIMER menu, and then press

OK to go to the screen below (or press 9 to go to the NEW TIMER menu):

Enter the OFF time as above and press OK, (or just press OK if you don’t want to set an

OFF time). Press Clear if you enter a wrong time. The display shows 1. DAILY on the

bottom line (top line blank).

9. SET TIMER

1. DAILY

You will see NEW TIMER on the top line. If no timers have yet been entered the up and

down Menu buttons will do nothing. If there are other timers already in memory the up and

down buttons will cycle around them and will always include NEW TIMER in the loop if

there is empty space in the memory.

Using the up or down Menu buttons you can cycle around 1. DAILY, 2. ONCE ONLY, and

3. RANDOM. Select the one of your choice and press OK. The display again shows NEW

TIMER. Now the up and down Menu buttons will cycle through the entered events in the

form

12ON 12:34am

OFF 12:45pm

9. NEW TIMER

Note you can set a total of 12 “timer pairs” i.e. ON-OFF times. If you choose to set an ON

time with no corresponding OFF time for that unit code (or vice versa) it still counts as a

“timer pair.” RANDOM varies the time during the programmed hour.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

You can cycle through (Review) your stored timers by pressing the up or down Menu

buttons. This will show the stored timers in the form below

Reviewing/Canceling Timers

Press either of the Menu up/down buttons (under the lid to the bottom right of the display).

The display then shows ENTER PIN (Personal Identiﬁcation Number) in the top line.

12ON 12:34am

OFF 12:45pm

While a timer is on the display, pressing Clear deletes it. You are ﬁrst asked: CLEAR

TIMER 1. YES 2. NO .

ENTER PIN

12:00 am

9. CLEAR TIMER

1. YES 2. NO

The default PIN is 0000, you’ll ﬁnd out later (page 24) how you can change this, but for

now press 0000 on the keypad (under the lid to the bottom right of the display). This clears

the top line and shows * for each number entered.

Pressing 1 (for YES) deletes the timer and takes you to NEW TIMER to allow you to start

entering a new timer. Pressing 2 takes you to NEW TIMER without deleting the one that

was on the screen. Press Clear to back out of the Menus.

****

12:00 am

Replacing Timers

This takes you to the ﬁrst level of the menu at step 1. This is the INSTALLATION level. The

display looks like this:

You can cycle through (Review) your timers by pressing the up or down Menu buttons.

This will show the stored timers in the form below

12ON 12:34am

OFF 12:45pm

1. INSTALL

While a timer is on the display, pressing OK takes you to the Replace Timer screen below.

Press an up or down menu button until you reach the SET TIMER menu, and then press

OK to go to the screen below (or press 9 to go into the SET TIMER menu ):

9. REPLACE TIMR

1. YES 2. NO

9. SET TIMER

Selecting 1 for YES, takes you to the UNIT NUMBER screen below where you can

continue to enter a new timer as described on page 29. Selecting 2 for NO takes you to the

NEW TIMER screen so you can enter a new timer without replacing the existing one. Press

Clear the back out of the menus.

You will see NEW TIMER on the top line. If no timers have yet been entered the up and

down Menu buttons will do nothing. If there are other timers already in memory the up and

down buttons will cycle around them and will always include NEW TIMER in the loop if

there is empty space in the memory.

9. UNIT NUMBER

9. NEW TIMER

Note you can also clear ALL timers as described on page 25.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the system

Arming the system

If there’s a problem

Press ARM HOME on the Console to arm all Door/Window Sensors instantly. Motion

Detectors will not trip the system when it is armed in the ARM HOME mode.

If a door or window is open and you try to arm the system the display looks as below.

Where ZONE 9 is the door or window that’s open.

Press ARM AWAY to arm all Door/Window Sensors and Motion Detectors. This arms the

system after a set delay. The delay will be what you speciﬁed as the EXIT DELAY on page

27 (1 minute default). If you arm the system in the AWAY mode you will also have an entry

delay when you enter your home before the alarm trips, to give you time to disarm it. This

delay will be what you speciﬁed for your ENTRY DELAY on page 27 (30 second default).

OPEN

ZONE 9

If a Door/Window Sensor or Motion Detector has not reported in within the last 4 hours

and you try to arm the system the display shows:

Pressing ARM on the Keychain remote always arms in the AWAY mode, but arms

instantly.

PROBLEM

ZONE 9

Disarming the system

Pressing DISARM on the Keychain remote disarms the system instantly. The zone that

was violated is shown in the display. To remove this press Arm and Disarm again.

If a Door/Window Sensor has been tampered with, e.g. the cover is open, and you try to

arm the system the display shows:

To disarm from the Console: Enter your 4 digit PIN (Personal Identiﬁcation Number) this

will be 0000 unless you changed it (see page 24).

TAMPER

ZONE 9

ENTER PIN

12:00 am

For all the above situations, pressing the Clear (Bypass) button bypasses the problem

zone and lets you arm the system. After pressing Bypass the next problem zone is

displayed, (if there is more than one).

Entering the PIN clears the top line and shows * for each number entered.

You can’t arm the system while there’s a problem zone unless you ﬁx the problem, or

bypass the zone. If you try to arm the system while there’s a problem with one or more

zone you will hear a repetitive “trouble alarm” to alert you that you need to bypass or ﬁx

the problem zone(s).

****

12:00 am

Note also, if the Console itself has been tampered with, i.e. the door to the upper right of

the display is open, the problem must be ﬁxed (close the door) before you can arm the

system. Note if the system is armed and this door is tampered with, the alarm trips.

If the unit was armed, (in either ARMED HOME or ARMED AWAY modes) it will disarm

when the PIN is entered, and return to the time display, with DISARMED in the top line.

If you bypass a zone and then arm the system, that zone stays bypassed until you disarm

the system.

DISARMED

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the system

Controlling Lights and Appliances

If you install one or more Lamp Modules (sold separately), see next page, you can control

lights around your home from the Console. When the Console is in its normal state it

displays HOME CONTROL in the display. When its in this state you can simply press the

number button on the Console corresponding to the number set on the module and then

press On or Off on the Console’s control panel to control the light connected to the module.

When there’s an alarm

When the system is armed (in Home or Away mode) and you open a protected door or

window, or walk past a Motion Detector (if armed in the Away Mode), or activate the Panic

feature (by pressing Arm and Disarm at the same time on the Key Chain Remote) the

alarm trips. The following then happens:

You can also control lights set to your Security LIGHTCODEs from the A and B buttons on

the Key Chain Remote. The A buttons on the Key Chain Remote control lights connected

to X10 Modules that are set to the Security LIGHTCODE you set in the Console. (See step

4 on page 26). The B buttons control modules set to the next sequential number. I.E. if you

set your Security LIGHTCODE to 1, the A and B buttons on the Key Chain Remote will

control X10 Modules that are set to Unit Codes 1 and 2. If your Security LIGHTCODE is

10, the A and B buttons will control Modules 10 and 11. If your Security LIGHTCODE to 16,

the A and B buttons will control 16 and 1, etc.

A loud siren sounds.

Lights (set to the two security codes) ﬂash on and off (if you set up X10 Modules). See

page 36.

The Console dials the ﬁrst phone number you set up. It then starts to play the recorded

message you stored. E.G. “There’s an alarm in progress at (your address), at the end of

this message please press any button on your touch-tone phone to listen in.” Note, it might

take a while before the person the Console called picks up the phone so they might miss

the ﬁrst part of your message, but the message is repeated 3 times, so they will get to hear

the complete message.

Any lights set to your two Security LIGHTCODEs ﬂash on and off when the alarm trips.

They stay on after an alarm until you turn them off, either from the Console, or from the

Key Chain Remote.

When the person who was called answers the call and presses a button on their phone this

activates a microphone in the Console and they will be able to listen in to you home, and

will be able to determine if there is suspicious activity going on. They can then take action.

E.G. call the Police for you.

These lights also blink on for a second when the alarm is armed in the HOME Mode, or

turn on for the exit delay time when the alarm is armed in the AWAY Mode.

Refer to either version below depending on which version you purchased.

IMPORTANT: Do NOT program the Console to call the Police directly.

NOTES:

The person who answers the phone needs to wait for a gap between the messages before

they can press a button on their phone to listen in (the message repeats three times, but

might have already played once or twice before the person answers the phone).

Pressing both PANIC buttons at the

same time activates the panic alarm,

BATTERY

even if the Console is not armed.

ARM

If no one answers the call (and presses a button on their phone) before the third message

is played, the Console dials the next number stored. It can take quite a long time to dial all

the numbers if you’ve stored 6 of them, and no one answers. But the siren stops sounding

after 4 minutes in any case (the unit still dials all the numbers stored unless someone

answers the call (and presses a button on their phone).

PANIC

LIGHTS ON/OFF control lights

connected to X10 Modules that are

set to the Security LIGHT CODE you

set in the Console (see page 26).

DISARM

LIGHTS

OFF

If the system is tampered with

If the system is armed and someone tampers with (opens the cover) on a Door/Window

Sensor or the Console, the same thing happens as when the alarm is tripped by any

other method. If the system is NOT armed and someone tampers with a Sensor or the

Console, the word TAMPER appears in the display but the system does not trip. You must

ﬁx the tamper before you can arm the system. Press Arm then Disarm to remove the word

TAMPER from the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Lamp Modules

Operation from an Outside Telephone

The Console has remote telephone access, with voice responses to acknowledge receipt

of remote commands.

Setting the (optional) Lamp

Module’s Code

UNIT CODE

DIAL

When you call home, the Console answers and says “Please enter PIN.” You enter your

PIN using the touch tone buttons on the remote telephone.

Using a small screwdriver, set the red

House Code dial to the same letter as

your Console is set to. Set the Black Unit

Code dial to any unused number.

If the PIN is entered correctly it says “PIN accepted”. If wrong it says “Error.”

Pressing 0, then * (on the remote telephone’s touch tone keypad) arms the Console.

Pressing 0, then # disarms the Console.

HOUSE CODE

DIAL

Pressing 9, then 9, then * tells you the current system status: I.E. it says Armed Home,

Armed away, Disarmed, Panic alarm, or Alarm in zone (1 – 32).

Ratings

The Lamp Module can be used to control an incandescent lamp rated up to 300W. It is not

suitable for other types of lamps such as ﬂuorescent or energy saving lamps, low voltage

lamps, or lamps that include a dimmer control. Caution: Do not connect an appliance

such as a coffee pot or heater to a Lamp Module. It may damage the Module and/or the

appliance and could cause a ﬁre hazard. Use an Appliance Module instead.

The numbers 1 – 32 in the display refer to up to 32 “zones.” These represent the Door/

Window Sensors and/or Motion Detectors you installed. Therefore if the alarm tripped

because zone 3 was violated, when you call in and press 9, 9, * you will hear “Alarm in

zone 3.”

Remotely controlling lights (or appliances) via telephone

If you install one or more X10 Modules (sold separately), see previous page, you can

control lights and appliances around your home from any touch tone telephone in the

world.

When you call home, the Console answers and says “Please enter PIN.”

If the PIN is entered correctly it says “PIN accepted”. If wrong it says “Error.”

If you then press 4, then * on the touch tone phone, it says “4 On” and turns on any X10

Module(s) set to Unit Code 4 (and the same Housecode as the Console is set to).

If you then press 1, then 6, then # on the touch tone phone, it says “16 Off” and turns off

any X10 Module(s) set to Unit Code 16 (and the same Housecode as the Console is set

to).

Plug the Module into

the same wall outlet

as your controller (see

testing below).

Set the House Code

and Unit Code.

Plug a lamp into

the Module.

If you own an answering machine.

If you own an answering machine, you will normally set it to answer after a few rings.

In this case, when the answering machine answers a call (or if there’s someone home

who picks up the phone), the security system will NOT answer the call and will NOT

say “Please enter PIN.” You can still however go ahead and enter the PIN to access

the security system features above. Just wait until your answering machine ﬁnishes its

outgoing message and then enter your security system PIN. Note, your answering machine

will record the touch tones you hear when you press buttons to turn lights on and off, etc.,

and will also record the messages played back by the security system.

Testing The Module

Make sure the lamp’s switch is on. Plug the Module into the same wall outlet as your

Console’s power supply, press the On and Off buttons on the Console that correspond to

the Unit Code setting on the Module. If the Module turns on and off you can unplug the

Module and move it to its permanent location.

If you can’t control the module, visit www.x10.com for help.

Download from Www.Somanuals.com. All Manuals Search And Download.

Battery Information

General

Door/Window Sensors and Motion Detectors

Door/Window Sensors, Motion Detectors and Keychain remotes are designed to operate

for approximately one year when ﬁtted with the appropriate batteries. Since operating

conditions vary from installation to installation however, it is recommended that all batteries

are replaced every 6 months.

Battery Replacement

If a zone has not reported in to the Console during the last four hours, the display will show

PROBLEM and the appropriate zone number when you try to arm the system. This is most

likely caused by dead batteries in the Motion Detector or Door/Window Sensor for that

zone.

Security Console

As with the remotes, as long as the batteries have not completely failed they may be

replaced with fresh batteries without the need to reinstall the Motion Detector or Door/

Window Sensor. After removing the old batteries the new batteries must be ﬁtted within 30

seconds to ensure that the code is retained.

Battery backup

The batteries in the Security Console are used as a backup when there has been a power

failure. The batteries provides approximately 12 hours of backup time provided the alarm

has not been triggered.

While on battery backup, the Console will continue to operate, and will sound the siren and

dial out if the alarm is tripped. It will not, of course, ﬂash the house lights (because there’s

no AC power).

Testing the Door/Window Sensor

Once the batteries have been replaced, the Door/Window Sensor should be tested as

follows:

If both the AC supply and the batteries fail, the Console will no longer dial out or sound the

siren. You will not lose its telephone numbers, recorded message, or installed sensors and

remotes, but you will need to reset the clock for the correct time of day.

• Make sure the system is NOT armed.

• Open the door or window with the sensor attached. The Console chimes to acknowledge

and the zone # is displayed on the LCD.

Battery Replacement

Batteries can be replaced at any time, even while the unit is powered up. There is no

special procedure for battery replacement. Use 4 AA alkaline batteries.

• If you don’t hear a chime, reregister the Door/Window Sensor, as described on page 13

Testing the Motion Sensor

To test the Motion Detector:

Keychain Remotes

• Make sure the system is armed.

Battery Replacement

• Press the TEST button on the back of the Motion Detector. The alarm trips. Press disarm

on the Keychain Remote.

Providing the batteries have not already failed, they can be replaced with fresh batteries

without the need to reregister the remote. After removing the old batteries fresh batteries

must be ﬁtted within 30 seconds to ensure that the security code is retained.

• If the alarm doesn’t trip, reregister the Motion Detector, as described on page 16.

Gently pry the 2 halves of the Keychain Remote’s case apart and install two CR2016

lithium batteries in the compartment (+ facing up). Press the 2 halves of the cabinet back

together.

Clearing Remotes & Sensors from the Console

Once the batteries have been replaced, conﬁrm that the remote is still registered with the

Console by arming the system. If it does not arm, the code has been lost and you will need

to proceed as described below.

If you suspect that a neighbor’s system is causing false alarms, or if you need to reinstall

remotes, Door/Window Sensors, and Motion Detectors for any other reason, you can

clear all sensors and remotes from the Console’s memory by following the steps on page

25. Before reregistering your remotes, Door/Window Sensors, and Motion Detectors you

should reinitialize them - remove the batteries, press a button for 5 seconds then reﬁt the

batteries. Then follow the steps to reinitialize the unit (pages 12, 13, or 16 as appropriate).

If the batteries have failed completely, the remote’s code will have been lost. The remote

will need to be reinstalled following the procedure on page 12.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

PROBLEM

SOLUTION

If the system does not arm.

•

Check that the indicator on the Remote

turns on when you press ARM.

Replace the batteries and reregister the

If you hear a repetitive trouble alarm when

you try to arm the system, and it does not

arm.

Check the Console’s display. If a door or

window is open, its zone # will indicate

there’s a PROBLEM.

Remote with the Console if necessary.

•

Press DISARM. Check each Door/

Window Sensor is working properly and

that no doors or windows are open.

Then arm the system.

Or:

•

While the trouble alarm is sounding,

Console displays PROBLEM followed by

Zone number when you try to arm it.

One of the sensors/motion detectors has

not reported in, in the last 4 hours.

press CLEAR on the Console to

bypass the problem zone (the display

shows that it has been BYPASSED).

Then arm the system again.

Check that the batteries in the sensor/

motion detector are good.

Or a protected door or window is open.

•

Or if the display shows TAMPER,

check the cover on the Door/ Window

Sensor for that zone.

If you need to arm the system and want to

ignore a sensor/motion detector which is

not functioning:

Or check that the upper right lid on the

Console it closed.

1. Press CLEAR on the Console while the

problems is being displayed.

Arm the system in the AWAY mode.

If the alarm trips when you enter the

house before you have time to disarm it.

2. Then press ARM on the Remote. The

problem zone is not protected but all

other zones are armed.

Lights will not turn on or off from the ON or

OFF buttons on the Keychain Remote.

•

Be sure you set the correct SECURITY

LIGHT Code in the Console, see pages

26 and 35.

Be sure the light you are trying to

control has its on/off switch in the on

position. Be sure its bulb is good.

•

Plug the Module into another outlet

near the Console.

Check that the indicator on the Remote

comes on when you press a button.

Replace batteries and reregister remote

if necessary.

•

Check the dials on the Modules.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

PROBLEM

SOLUTION

PROBLEM

SOLUTION

If you do not hear a beep from the

Console when you register a Door/

Window Sensor or Motion Detector.

You open a door or window and the alarm

does not trip.

With the Console NOT armed check that

it chimes when you press TEST on the

Door/Window Sensor, or the alarm trips

when you press test on a Motion Detector

(when the system IS armed). If it does,

then the sensor is already installed and no

further action is necessary. If not:

•

Check that the system is armed.

Check to see if the alarm trips when

you press TEST inside the Door/

Window Sensor.

•

If the alarm does not trip when you

press TEST, check that the indicator on

the sensor comes on when you press

TEST.

•

Reregister the sensor/motion detector

(see Setting Up Door/Window Sensors

and Setting Up Motion Detectors.

If the indicator does not come on, replace

the batteries and reinstall the sensor if

necessary.

If the battery indicator on the Console is

on.

Replace the Console’s batteries. Four AA

alkaline batteries provides approximately

12 hours of backup. Replace batteries at

least once a year.

If you lose your remote control.

Reinstall your complete system to prevent

someone else from using the lost remote

control. See bottom of page 39.

The system ﬂashes lights by repetitively

transmitting the SECURITY light on and

off codes.

If appliances turn off during an alarm.

A neighbor may have a compatible

system. Reinstall the complete system so

that it chooses different RF codes. See

bottom of page 39.

If the system Arms or Disarms by itself

Any Appliance Modules set to the same

codes will therefore turn on and off.

If the light on the Keychain Remote stays

on during initialization.

Remove the batteries, press a button

for a few seconds, release, then replace

the batteries. Press and hold the ARM

button on the Keychain Remote for a

few seconds and then release it. This

initializes the remote and picks a random

code that is used when it is registered with

the Console. Reregister the remote.

If you do not hear a beep from the

Console when you press ARM to install a

Remote.

•

Re-initialize the remote (see page 12).

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

LIMITED ONE YEAR WARRANTY

X10 Wireless Technology, Inc. Limited One Year Warranty

PROBLEM

SOLUTION

X10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10

products to be free from defective material and workmanship for a period of

one (1) year from the original date of purchase at retail. X10 agrees to repair

or replace, at its sole discretion, a defective X10 product if returned to X10

within the warranty period and with proof of purchase. If service is required

under this warranty:

The alarm cause is shown on the display

even after disarming.

To remove, Arm and Disarm from a

remote, or disarm by pressing a menu key

and entering the PIN on the Console.

If the optional PowerHorn does not trip

when the alarm trips.

•

Be sure you set the dials on the

PowerHorn to the same SECURITY

LIGHT code as set in the Console.

Call 1-800-442-5065, visit www.x10.com, or e-mail [email protected].

For help or more information on setup, please visit:

www.x10.com/support

Plug the PowerHorn into another outlet

near the Console.

The Motion Detector causes false alarms.

• All brands of motion detectors sense

motion by detecting a change in

temperature, therefore do not place

the detector near any sources of heat

such as over a heating vent or an air

conditioner.

•

Do not place in a direct source of bright

light, such as sunlight.

Special Note

Intercom Systems

Intercom systems which send voice signals over existing electrical wiring may interfere

with the ability to control modules from your security system with the intercom in use. If the

intercom system has its own separate wiring it will not cause a problem.

Download from Www.Somanuals.com. All Manuals Search And Download.

Expanding Your System

Control an incandescent ceiling light, closet light, etc., with the convenient Screw-

in Lamp Module LM15A.

The X10 Security System can ﬂash lights on and off when the alarm trips. You connect

the lights you want it to control to X10 Lamp Modules and Wall Switch Modules (sold

separately). The Security Console also acts as a “Transceiver” and passes commands

received from wireless remote controls onto your house wiring, so you can use X10

wireless remote controls to control the same lights that the Security System ﬂashes. You

can also use the X10 remote controls to control Appliance Modules, etc.

R e p l a c e existing AC wall outlets with the Receptacle Module SR227. Has

one 15A/1800W controlled outlet and one outlet which is always on.

The Security Console also works with X10 EagleEye and ActiveEye wireless motion

sensors, again acting as a Transceiver, to pass the commands from the motion sensors to

the X10 Modules. The modules and controllers illustrated below represent just a few of the

wide range of X10 modules you can choose from to expand your Security System.

Visit our Web Site at: ww.x10.com

for more information on these and many other X10 products.

Use a controller to trigger the Remote Chime Module SC546 to call Dad for

dinner, or warn people you’re about to turn on the sprinklers.

UNIT

The EagleEye and ActiveEye Motion Sensors MS14A and MS16A can turn

on lights when someone enters a room or approaches your home.

HOUSE

Power Horn

Use the isolated contacts on the Universal Module UM506 to control pool

pumps, sprinklers, drapes and other low voltage equipment. Includes built in

warning beeper.

The Dual Floodlight Motion Detector PR511 turns on at dusk and/or when

it detects movement, and sends X10 signals to control other modules, or to

trigger ActiveHome Pro macros.

Fit a Wireless Wall Switch SS13A/SS15A anywhere you need an extra

switch – with no wires. Sends commands to the Security Console, which

passes them to the X10 modules, just like a remote control does.

The Thermostat Setback Controller TH2807 mounts below your

thermostat to reduce the room temperature at night or at the times you set

to save energy. No wiring needed to your existing thermostat.

Turn entrance or garage lights on from your car with the convenient Keychain Remote

KR21A (or KR19A).

Plug in a Heavy Duty Module HD245 to control 220V appliances such as air

conditioners and water heaters.

Replace your existing wall switches with the Wall Switch Module WS467.

Installs like a regular dimmer. On/Off and Bright/Dim functions. Other models

available for 3-way and ﬂuorescent lighting.

Also compatible with ActiveHome Pro, and FireCracker Computer Interface.

Visit www.x10.com for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

X10 Wireless Cameras

You can add X10 2.4 GHz wireless cameras to you system. These work

independently of your security system but can be remotely controlled using

the same remote controls that you use to turn lights and appliances on and off

remotely. This adds another level of protection for you home – not only will your

security system trip if someone breaks in, but you can also use X10 cameras with

your VCR to capture images of the burglar!

XCam2

Camera

Ninja Pan ‘n Tilt Unit

Increase the viewable area of your

camera by 400%. The standard

XCam2 records everything within

a 60° x 60° ﬁeld of view. But with

the Ninja Robotic Mount, you get

sweeping 240° x 130° views.

There is even software available that lets your PC capture images from X10

cameras and e-mail them to you.

The Vanguard Professional Pan/Tilt/Zoom Camera is X10’s premier video

surveillance solution. It has superior image quality, a high powered zoom, and

pan and tilt motion. You can operate the camera through walls using the remote

control included with it.

Ninja

Base

The camera uses X10’s 2.4 GHz wireless technology to transmit live video

through walls to a television up to 100 feet away. If you prefer a secure video

connection, you can use a video cable to connect the camera directly to your TV.

VCR Commander

Record only when there’s movement in

your camera’s ﬁeld of view. The VCR

Commander issues “STOP” and “START”

commands to you VCR anytime there’s

movement within 30 feet of your camera.

You can combine multiple cameras to provide comprehensive coverage of your

home or business. Use the remote control to switch between cameras so that you

don’t miss anything that goes on.

XRay Vision

Monitor your home from any city in

the world! With XRay Vision Software

you can monitor your home from any

computer with an Internet connection.

E-mail video snapshots to your

personal account or view them on

your own secure Web Site.

Visit www.x10.com for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Whirlpool Air Conditioner ACS082PP0 User Manual
Whirlpool Trash Compactor TC4700X User Manual
Williams Furnace 14036 User Manual
Winegard TV Antenna GM 1518 User Manual
Woods Equipment Brush Cutter D80 2 User Manual
Wyse Technology Computer Drive R10L User Manual
Xerox Flat Panel Television VO400E User Manual
Xerox Printer WorkCentre 3215 User Manual
Yamaha Cassette Player KX E100 User Manual
Zephyr Ventilation Hood COK E42SX User Manual