X10 Wireless Technology Home Security System MS18A User Manual

Initializing Motion Detectors  
If desired, you can specify what zone you want the Motion Detector to be installed  
into. Just press the number of the zone you want on the Console’s keypad, before  
you press the TEST button on the back of the Motion Detector.  
Remove the cover on the front of the Motion Detector and  
install 2 AA alkaline batteries in the compartment.  
Replace the cover to deactivate the tamper switch.  
Press and hold the TEST button on the back of the Motion  
Detector for 3-4 seconds and then release it. This initializes  
the Motion Detector and picks a random code that is used  
when it is registered with the Console. Place the unit face  
down, so that it won’t see any motion during the registering  
process below.  
Press Clear to back out of the menus. You are asked to confirm, 1. YES, 2 NO.  
Press 1 to go back to the HOME CONTROL screen. Press 2 to stay in the INSTALL  
menu.  
Installing the Motion Detector  
• Attach the Motion Detector to a wall at a height of 5 to 6 ft. using the mounting  
bracket and screws provided.  
Registering the Motion Detector with the Console  
• Point the Motion Detector so that it looks slightly downwards.  
Press either of the Menu Start up/down buttons (under the Console’s lid to the left of  
the display). The display then shows ENTER PIN (Personal Identification Number)  
in the top line.  
• Set the slide switch (on the back) to position 1 for instant triggering for maximum  
sensitivity, or position 2 to trigger only after two movements have been sensed.  
ENTER PIN  
12:00 am  
90˚  
R
O
T
C
E
T
E
D
N
IO  
T
O
M
5-6ft  
The default PIN is 0000, so press 0000 on the keypad, or enter your PIN if you  
changed it (see Security System Owner’s Manual). This clears the top line and  
shows * for each number entered.  
30-40ft  
****  
12:00 am  
This takes you to the first level of the menu at step 1. This is the INSTALLATION  
level. When you see INSTALL on the display, press OK. The display then looks like  
this:  
Testing the Motion Detector  
• Set the slide switch on the Motion Detector to position 1.  
• Press and hold the TEST button for about a second.  
The LED flashes twice when you release it.  
1. INSTALL  
ZONE  
Wait 20 seconds for the Motion Detector to settle.  
Walk in front of the Motion Detector. The indicator LED  
lights each time it senses movement. Check the coverage  
area and reposition the sensor as required.  
Now simply press the TEST button on the back of the Motion Detector (or turn the  
unit over so that it sees motion). The Console will acknowledge that it has been  
registered by displaying (for example) ZONE 3 SET.  
• Press the TEST button to return to normal operating  
mode.  
Note: The Motion Detector will automatically return to  
normal operating mode after about 2 minutes.  
Repeat this for any other Motion Detectors you want to register. The display  
increments to ZONE 4 SET, etc. as you install more Motion Detectors.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Weslo Treadmill WLAW35075 User Manual
West Bend Bread Maker L4854 User Manual
Westinghouse Laptop NB 14w2 User Manual
Whirlpool Air Conditioner ACM052 User Manual
White Rodgers Thermostat 1E30N 910 User Manual
Yamaha Musical Instrument AR 80 User Manual
Zanussi Clothes Dryer TC 450 User Manual
Zanussi Dishwasher 402020 User Manual
Zenith Projector PRO895X User Manual
Zenith Water Dispenser 30009 User Manual