MODEL M1036
MICRO MILL
OWNER'S MANUAL
COPYRIGHT © NOVEMBER, 2005 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in China
#7735EW
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
INTRODUCTION..................................................................................................3
Woodstock Technical Support............................................................................ 3
About Your New Micro Mill ............................................................................... 3
Specifications............................................................................................... 3
Controls and Features..................................................................................... 4
SAFETY............................................................................................................5
Standard Safety Instructions ............................................................................. 5
Additional Safety Instructions for Micro Mills ......................................................... 7
ELECTRICAL......................................................................................................8
110V Operation............................................................................................. 8
Extension Cords ............................................................................................ 8
Grounding ................................................................................................... 8
SET UP ............................................................................................................9
Unpacking ................................................................................................... 9
Items Needed for Set Up.................................................................................. 9
Inventory ...................................................................................................10
Machine Placement .......................................................................................11
Cleaning Machine .........................................................................................11
Mounting to Workbench..................................................................................12
Mounting Headstock to Column.........................................................................12
Compound Slide Table ...................................................................................13
Vise..........................................................................................................13
Test Run and Spindle Break-in..........................................................................14
OPERATIONS ................................................................................................... 15
General .....................................................................................................15
Table Travel ...............................................................................................15
Graduated Dials ...........................................................................................16
Backlash ....................................................................................................16
Headstock Height .........................................................................................16
Downfeed Controls........................................................................................17
Digital Height Gauge .....................................................................................17
Depth Stop .................................................................................................18
Changing RPM..............................................................................................18
Drill Chuck .................................................................................................19
Drill Chuck Removal ......................................................................................19
Collets ......................................................................................................20
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE ................................................................................................. 21
General .....................................................................................................21
Cleaning ....................................................................................................21
Table & Base...............................................................................................21
Lubrication .................................................................................................22
SERVICE......................................................................................................... 23
General .....................................................................................................23
Gibs..........................................................................................................23
Replacing Motor Brushes.................................................................................24
Fuse Replacement ........................................................................................24
Troubleshooting ...........................................................................................26
PARTS ........................................................................................................... 27
Parts List ...................................................................................................28
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
INTRODUCTION
Woodstock Technical Support
We stand behind our machines! In the event that questions arise about your machine, parts are miss-
ing, or a defect is found, please contact Woodstock International Technical Support at (360) 734-3482 or
lems and send out parts for warranty claims.
If you still have questions after reading the latest manual, or if you have comments please contact us at:
Woodstock International, Inc.
Attn: Technical Support Department
P.O. Box 2309
Bellingham, WA 98227
About Your New Micro Mill
Your new SHOP FOX® Micro Mill has been specially designed to provide many years of trouble-free ser-
vice. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and
reliable operation.
This Micro Mill is perfect for machining high precision small parts for working models or drilling holes
that need to be identical depth and equal distance apart. The Model M1036 includes a removable cross
feed table, a digital depth gauge, and a variable speed range from zero-5000 RPM.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to include all the information necessary for safety, ease of assembly, practical use and durability
of this product.
Specifications
Motor.................................................. 0.2 HP, 2A, 110V, Single-Phase
Drilling Capacity ...................................................................... 1⁄4''
Spindle Taper.......................................................................... JT1
Spindle Travel ........................................................................11⁄2''
Headstock Travel ....................................................................73⁄4''
Spindle to Column Distance........................................................61⁄2''
Table Travel, Longitudinal .........................................................23⁄4''
Table Travel, Cross..................................................................51⁄2''
Column Swivel........................................................................360°
Speeds ............................................................... Low Range: 0–3600
........................................................................High Range: 0–5000
Weight .............................................................................. 31 lbs.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Controls and Features
A. ON/OFF Switch
B. RPM Control Knob
Q
C. Fuse Box
D. Clutch Knob
E. Micro Downfeed Knob
A
F. Compound Slide Table
P
G. Base
H. Crossfeed Handwheel
I. Collet Chuck (Optional Accessory)
J. Longitudinal Handwheel
K. Vise (Optional Accessory)
L. Drill Chuck
B
O
M. Headstock
C
N. Digital Height Gauge
O. Downfeed Lever
P. Column Lock Knob
Q. Pulley Cover
N
D
M
I
E
K
L
F
J
G
H
Figure 1. M1036 Controls and features.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
SAFETY
READ MANUAL BEFORE OPERATING MACHINE.
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury.
This symbol is used to alert the user to useful information about proper
operation of the equipment, and/or a situation that may cause damage
to the machinery.
NOTICE
Standard Safety Instructions
1. Thoroughly read the Instruction Manual before operating your machine. Learn the applications,
limitations and potential hazards of this machine. Keep the manual in a safe and convenient place
for future reference.
2. Keep work area clean and well lighted. Clutter and inadequate lighting invite potential hazards.
3. Ground all tools. If a machine is equipped with a three-prong plug, it must be plugged into a three-
hole grounded electrical receptacle or grounded extension cord. If using an adapter to aid in accom-
modating a two-hole receptacle, ground using a screw to a known ground.
4. Wear eye protection at all times. Use safety glasses with side shields or safety goggles that meet
the appropriate standards of the American National Standards Institute (ANSI).
5. Avoid dangerous environments. Do not operate this machine in wet or open flame environments.
Airborne dust particles could cause an explosion and severe fire hazard.
6. Ensure all guards are securely in place and in working condition.
7. Make sure switch is in the OFF position before connecting power to machine.
8. Keep work area clean, free of clutter, grease, etc.
9. Keep children and visitors away. Visitors must be kept at a safe distance while operating unit.
10.Childproof your workshop with padlocks, master switches or by removing starter keys.
11.Stop and disconnect the machine when cleaning, adjusting or servicing.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
12.Do not force tool. The machine will do a safer and better job at the rate for which it was
designed.
13.Use correct tool. Do not force machine or attachment to do a job for which it was not designed.
14.Wear proper apparel. Do not wear loose clothing, neck ties, gloves, jewelry, and secure long hair
away from moving parts.
15.Remove adjusting keys, rags, and tools. Before turning the machine on, make it a habit to check
that all adjusting keys and wrenches have been removed.
16.Avoid using an extension cord. But if you must use one, examine the extension cord to ensure it
is in good condition. Immediately replace a damaged extension cord. Always use an extension cord
that uses a ground pin and connected ground wire. Use an extension cord that meets the amp rating
on the motor nameplate. If the motor is dual voltage, be sure to use the amp rating for the voltage
you will be using. If you use an extension cord with an undersized gauge or one that is too long,
excessive heat will be generated within the circuit, increasing the chance of a fire or damage to the
circuit.
17.Keep proper footing and balance at all times.
18.Lock mobile base, if used, to prevent the machine from moving during operation.
19.Do not leave machine unattended. Wait until it comes to a complete stop before leaving the
area.
20.Perform machine maintenance and care. Follow lubrication and accessory attachment instructions
in the manual.
21.Keep machine away from open flame. Operating machines near pilot lights or open flames creates
a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause an explo-
sion. Do not operate the machine in high-risk areas, including but not limited to, those mentioned
above.
22.If at any time you are experiencing difficulties performing the intended operation, stop using the
machine! Then contact our technical support or ask a qualified expert how the operation should be
performed.
23. Habits—good and bad—are hard to break. Develop good habits in your shop and safety will become
second-nature to you.
24. Be aware that certain metal shavings and cutting fluids may cause an allergic reaction in people
and animals, especially when cutting fumes can be inhaled. Make sure you know what type of metal
and cutting fluid you will be exposed to and how to avoid contamination.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Additional Safety Instructions for Micro Mills
READ and understand this
entire instruction manual
before using this machine.
Serious personal injury
may occur if safety and
operational information is
not understood and fol-
lowed. DO NOT risk your
safety by not reading!
USE this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.
1. MILL ASSEMBLY. Do not operate until unit is assembled and installed according to instructions.
2. USER TRAINING. This mill is intended to be used by operators who have the proper experience and
training with this type of machine. Make sure you understand the use and operation of all controls.
3. MILL INSPECTION. Inspect the mill for damaged or worn parts before operation. Repair damage or
perform maintenance immediately. Remove chuck key and any service tools immediately after use.
4. CUTTING TOOL INSPECTION. Inspect drills and end mills for sharpness, chips, or cracks before
each use. Replace dull, chipped, or cracked cutting tools immediately. Handle new cutting tools
with care. Leading edges are very sharp and can cause lacerations.
5. SECURING WORKPIECE. Never hold a workpiece by hand for any type of machining operation. Hold
your workpiece secure with a mill vise, step clamps, etc.
6. CUTTING TOOLS. Use the correct tool for the material you are milling. Make sure that the cutting
tool is chucked or secured properly. Cutting tools that are loose or not rotating correctly can come
off and cause serious personal injury.
7. CLEARING CHIPS. Turn machine OFF and wait for cutting tool to come to a complete stop before
clearing away chips. Chips are sharp. Use a brush or vacuum to remove them.
8. FEED AND SPEED RATES. Research the proper feed and speed rate for the material you are
machining. Do not exceed these recommended rates.
9. TURNING OFF MILL. Allow the mill to come to a complete stop before leaving it unattended. DO
NOT stop the spindle with your hand.
10. SERVICING MILL. Make sure mill is turned OFF, unplugged, and the mill has come to a complete
stop before servicing. Perform routine inspections and correct service related issues promptly.
11. CUTTING FLUIDS. Cutting fluids used for machining may contain hazardous chemicals. Read and
understand all user information on the cutting fluid container and take necessary precautions.
12. AVOIDING ENTANGLEMENT. Keep loose clothing articles such as sleeves, belts or jewelry items
away from the mill spindle.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
ELECTRICAL
110V Operation
The SHOP FOX® Model M1036 is prewired for 110 volt
operation. The motor supplied with your new Micro Mill
is rated at 0.2 HP and will draw approximately 2 amps. A
5-15 plug is included for your machine and is intended to
be plugged into a matching 5-15 receptacle.
Connect your machine to a circuit (wire, breaker, plug,
receptacle) that is rated for at least 10 amps.
Keep in mind that a circuit being used by other machines
or tools at the same time will add to the total load
being applied to the circuit. Add up the load ratings
of all machines on the circuit. If the total amp load
exceeds the rating of the circuit breaker or fuse, use a
different circuit.
Figure 2. Typical 110V 3-prong plug and
outlet.
Extension Cords
This equipment must be grounded.
Verify that any existing electrical out-
let and circuit you intend to plug into
is actually grounded. If it is not, it will
be necessary to run a separate 12 AWG
copper grounding wire from the outlet
to a known ground. Under no circum-
stances should the grounding pin be
removed from any three-pronged plug
or serious injury may occur.
When it is necessary to use an extension cord, use the
following guidelines:
•
•
•
•
•
Use cords rated for Standard Service
Never exceed a length of 100 feet
Use cords with 16 ga. wire or bigger
Ensure cord has a ground wire and pin
Do not use cords in need of repair
Grounding
This machine must be grounded! The electrical cord sup-
plied with this machine comes with a grounding pin. Do
not remove it. If your outlet does not accommodate a
ground pin, have it replaced by a qualified electrician or
have an appropriate adapter installed.
Note: When using an adapter, the adapter must be
grounded.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
SET UP
Unpacking
The SHOP FOX® Model M1036 has been carefully pack-
aged for safe transporting. If you notice the machine has
been damaged, please contact your authorized SHOP
FOX® dealer immediately.
READ and understand this
entire instruction manual
beforeusingthismachine.
Serious personal injury
may occur if safety and
operational information
is not understood and fol-
lowed. DO NOT risk your
safety by not reading!
SUFFOCATION HAZARD!
Immediately discard all plastic bags and
packing materials to eliminate suffoca-
tion hazards for children and animals.
UNPLUG power cord
before you do any assem-
bly or adjustment tasks!
Otherwise, serious per-
sonal injury to you or
others may occur!
Items Needed for Set Up
The following items are needed, but not included, to
setup your machine:
•
•
•
•
•
Safety Glasses (for each person)........................1
Solvent ......................................................1
Shop Rags...................................................1
Wrench or Socket 10mm .................................1
Ruler.........................................................1
Bench Mounting Hardware (Optional)
•
•
•
•
•
•
Precision Level.............................................1
Phillips Head Screw 6mm x Length Varies ............2
Hex Nut 6mm ..............................................2
Flat Washer 6mm..........................................2
Metal Shim Stock ..........................................1
Drill and 6mm Bit..........................................1
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Inventory
The following is a description of the main components
shipped with the SHOP FOX® Model M1036. Lay the
components out to inventory them.
A
Box 1 Contents (Figure 3)
Qty
A. Headstock...................................................1
B. Collar........................................................1
C. Spacer .......................................................1
D. Base with Column .........................................1
E. Downfeed Lever Handle..................................1
F. Column Lock Knob.........................................1
G. Fence........................................................1
D
G
B
C
E
F
Figure 3. Box 1 contents.
Box 1 Tools and Hardware (Not Shown)
Qty
•
•
•
•
•
•
•
Phillips Head Screwdriver................................1
Hex Wrenches 2, 2.5, 3, 4mm ...................1 Each
Open End Wrench 5.5/7mm ............................1
Chuck Removal Wedge ...................................1
Round Belt..................................................1
Cap Screw M5-.8 x 12.....................................1
Square Nut M5-.8..........................................1
H
I
Box 2 Contents (Figure 4)
Qty
H. Compound Slide Table....................................1
I. Handwheel Handles ......................................2
Figure 4. Box 2 contents.
Box 2 Hardware (Not Shown)
Qty
•
•
•
•
T-Bolts M6-1 x 22..........................................4
T-Nuts M6-1 ................................................4
Hex Nuts M6-1..............................................2
Flat Washers 6mm.........................................2
NOTICE
When ordering replacement parts, refer
to the parts list and diagram in the back
of the manual.
If any parts appear to be missing, examine the packag-
ing carefully to be sure those parts are not among the
packing materials. If any parts are missing, find the
part number in the back of this manual and contact
Woodstock International, Inc. at (360) 734-3482 or at
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Machine Placement
Cleaning Machine
The table and other unpainted parts of your
Micro Mill are coated with a waxy grease that
protects them from corrosion during shipment.
Clean this grease off with a solvent cleaner or
citrus-based degreaser. DO NOT use chlorine-
based solvents such as brake parts cleaner or
acetone—if you happen to splash some onto a
painted surface, you will ruin the finish.
•
•
Workbench Load: Bolt your machine
to a sturdy workbench that will not tip.
Some workbenches may require additional
reinforcement to support both the machine
and the workpiece.
Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through the machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your Micro Mill.
NEVER use gasoline or
other petroleum-based
solvents to clean with.
•
•
Lighting: Lighting should be bright enough
to eliminate shadow and prevent eye strain.
Most
points, which make them
extremely flammable.
have low flash
Electrical: Electrical circuits must be
dedicated or large enough to handle
amperage requirements. Outlets must be
located near each machine, so power or
extension cords are clear of high-traffic
areas. Follow local electrical codes for
proper installation of new lighting, outlets,
or circuits.
A risk of explosion and
burning exists if these
products are used. Serious
personal injury may occur
if this warning is ignored!
ALWAYS work in well-
ventilated areas far from
possible ignition sources
when using solvents to
clean machinery. Many
solvents are toxic when
inhaled or ingested. Use
care when disposing
of waste rags and
towels to be sure they
DO NOT create fire or
environmental hazards.
MAKE your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. NEVER
allow untrained visitors in
your shop when assem-
bling, adjusting or operat-
ing equipment.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Mounting to Workbench
Mounting the mill to the workbench provides maximum
rigidity and prevents the mill from tipping. Mounting the
mill should be done before installing the headstock for
the best access to the mounting holes. When choosing a
location for the mill, make sure the cross feed and the
longitudinal handwheels extend out beyond the edge of
the table surface. This will allow unrestricted handwheel
operation.
To mount the mill to the workbench, do these steps:
1. Measure the thickness of the workbench and add
11⁄2" to determine the necessary screw length.
Figure 5. Mounting hole locations.
2. Mark your hole locations, using the mounting holes
in the base as a guide (see Figure 5).
3. Drill 3/16" holes through the workbench.
4. Place a precision level on the mill/drill table and
shim the mill/drill until it is level side-to-side and
front-to-back.
5. Bolt the mill to the workbench with two 6mm cap
screws (length determined in Step 1), hex nuts and
flat washers.
Mounting Headstock to
Column
Figure 6. Collar and spacer installed on
the column.
To install the headstock on the column, do these steps:
1. Set the base upright and slide the collar half way
down the column.
2. Secure the collar by tightening the cap screw with
a 4mm hex wrench, then slide the spacer over the
column (see Figure 6).
3. Insert the column lock knob assembly into the head-
stock, as shown in Figure 7.
4. Slide the headstock onto the column, line the chuck
up with the hole in the base, and lock it in place
with the column lock knob.
Figure 7. Installing the column lock knob.
5. Thread the downfeed lever into the hub and tighten
with the included wrench.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Compound Slide Table
Installation of the compound slide table is not necessary
when using the mill as a drill. The compound slide table
can be moved in the X and Y axis for use with milling
cutters.
To install the compound slide table, do these steps:
1. Thread the handwheel handles into the handwheels.
2. Remove the fence from the base if installed.
3. Slide the T-bolts into the T-slots and place the
compound slide table over the T-bolts, as shown in
Figure 8.
Figure 8. T-bolt installation.
4. Measure at the front and back of the compound
slide table as shown in Figure 9 to make sure the
compound slide table is parallel to the base.
5. Place washers over the T-bolts and secure the com-
pound slide table with the hex nuts.
Vise
To install the vise, do these steps:
1. Slide the T-nuts into the compound slide table.
2. Place the vise on the compound slide table and
loosely secure it by threading two M6-1 x 18 cap
screws with washers through the vise and into the T-
bolts, as shown in Figure 10.
Figure 9. Aligning the compound slide
table.
3. Align the vise parallel to the compound slide table
and tighten the cap screws.
Figure 10. Securing the vise.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Test Run and Spindle
Break-in
Complete this process once you have familiarized yourself
with all instructions in this manual and you have made
sure the machine is completely lubricated as described
in Lubrication on Page 22. It is essential to closely fol-
low the proper break-in procedures to ensure trouble free
performance.
NOTICE
Failure to follow the break-in proce-
dures included in this manual may lead
to shortened tool life and may void war-
ranty.
To begin the test run and spindle break-in procedure,
do these steps:
1. Make sure there are no obstructions around or
underneath the spindle.
2. Put on safety glasses, and make sure any bystanders
are wearing safety glasses and are out of the way.
3. Plug the machine in and turn the ON/OFF switch
ON, then set the mill to the slowest RPM. See Page
18 for adjusting RPM. The mill should run smoothly,
with little or no vibration or rubbing noises.
• If you hear squealing or grinding noises, turn the
machine OFF immediately. Wait for the mill to
stop moving, unplug the machine, and correct any
problems before further operation.
• If the source of an unusual noise or vibration is not
readily apparent, contact our technical support
for help at (360) 734-3482 or contact us online at
4. If the mill runs smoothly, allow it to run for 10 min-
utes at slow speed.
5. Slowly increase the RPM and allow it to run at a
medium RPM for another ten minutes.
6. Slowly increase the RPM and allow it to run at a high
RPM for another ten minutes.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
OPERATIONS
General
The Model M1036 will perform many types of operations
that are beyond the scope of this manual. Many of these
operations can be dangerous or deadly if performed incor-
rectly.
The instructions in this section are written with the under-
standing that the operator has the necessary knowledge
and skills to operate this machine. If at any time you
are experiencing difficulties performing any operation,
stop using the machine!
READ and understand this entire instruc-
tion manual before using this machine.
Serious personal injury may occur if
safety and operational information is not
understood and followed. DO NOT risk
your safety by not reading!
If you are an inexperienced operator, we strongly recom-
mend that you read books, trade articles, or seek training
from an experienced milling machine operator before per-
forming any unfamiliar operations. Above all, your safety
should come first!
Table Travel
The table can be moved in 2 axes. Each axis is indepen-
dently controlled by a crank handle. Each handle has a
graduated dial to accurately position the workpiece in
relation to the cutting tool. Each axis has the ability to
be locked in position. Locking the axis in place will help
keep workpiece vibration to a minimum.
DO NOT investigate problems or adjust
the Micro Mill while running. Wait until
the machine is turned off, unplugged
and all working parts have come to a
complete stop before proceeding!
Longitudinal Feed Control
The longitudinal feed is controlled by a crank handle at
the end of the table, and can be locked in position by the
cap screw located at the front of the table.
Cross Feed Control
The cross feed is controlled by the center crank handle,
and can be locked in position by the cap screw located
under the left side of the mill table.
Figure 11. Wear eye protection and secure-
ly clamp workpiece when operating mill.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Graduated Dials
Each mark on the handwheel graduated dials (Figure 12)
represents 0.001" of movement. One full rotation of the
handwheel is equal to 0.050". The graduated dials can be
"zeroed" by grasping the knurled section and rotating the
graduated dial to "0".
Graduated Dial
Example:
To drill a series of holes with 1⁄2" centers (0.500"), drill
the first hole, zero the graduated dial, move the table
0.500" (10 rotations of the handwheel) in the appropriate
direction, then drill the next hole.
Backlash
Figure 12. Graduated dial.
When changing table direction in either axis, the
handwheel will rotate a few degrees before the table
begins to move and the graduated dial must be adjusted.
This is backlash.
To correct for backlash, do these steps:
1. Turn the handwheel in the opposite direction of your
next operation.
2. Turn the handwheel to move the table in the intend-
ed direction.
3. When the lead screw catches and the table begins to
move, backlash has been eliminated and the gradu-
ated dial can be "zeroed."
Figure 13. Headstock height adjustment.
Note: You will not need to adjust for backlash as
long as the table moves in the same direction.
Headstock Height
Adjusting the height of the headstock, instead of extend-
ing the quill, maintains the rigidity of the mill and
requires less motion when using the downfeed lever.
To adjust the headstock height, do these steps:
1. Loosen the collar (Figure 13) and lower it to the
desired height.
2. Loosen the column lock knob and carefully lower the
headstock until it rests on the collar spacer.
Note: Raise the headstock by reversing Steps 1 & 2.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Downfeed Controls
Quill Feed Control
The quill feed is controlled by the downfeed lever shown
in Figure 14. The handle allows the mill to operate as a
drill.
Downfeed
Lever
To use the downfeed lever, do this step:
1. Pull the quill downfeed lever (Figure 14) forward
to feed the quill down towards the workpiece. The
quill feed handle is spring loaded to assist in return-
ing the handle to the upmost vertical position.
Micro Downfeed Knob
The micro downfeed knob is used to accurately control
Figure 14. Quill downfeed lever.
the quill depth (see Figure 15).
To use the micro downfeed handwheel, do these
steps:
Micro Downfeed
Knob
1. Push the clutch knob (Figure 15) in lightly and rotate
the micro downfeed knob until the clutch knob
engages the gear.
2. Rotate the micro downfeed knob clockwise to feed
the quill down and counterclockwise to raise the
quill.
Micro Downfeed
Clutch Knob
Digital Height Gauge
Figure 15. Micro downfeed controls.
The digital height gauge (Figure 16) provides accurate
height measurements, zeroing at any height, and
incremental readout adjustments.
ON/OFF button: Turns the digital height gauge ON or
OFF. This gauge does not automatically turn OFF, so the
batteries will die if the gauge is left ON.
ZERO button: Returns the digital readout to 0.000
independent of the height of the quill.
Battery
Cover
MM/IN button: Changes readout from inches to
millimeters.
PLUS and MINUS buttons: Adds or subtracts from the
number shown on the digital readout. You must hold the
button for several seconds before it begins to function.
Figure 16. Digital height gauge.
When the batteries wear out, open the cover shown in
Figure 16 and replace the battery.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Depth Stop
The depth stop allows the operator to make numerous
holes that all are the same depth or to hold the mill at a
specified depth.
To set the depth stop, do these steps:
1. Use the micro downfeed knob to set the desired
depth.
2. To set the quill to repeat the same depth, rotate
the graduated dial (Figure 17) past the O mark until
it stops, then tighten the set screw.
3. To lock the quill at the specified depth, rotate the
graduated dial past the 30 mark until it stops, then
tighten the set screw.
Figure 17. Depth stop.
Changing RPM
The variable speed dial shown in Figure 18 controls the
spindle speed and the pulleys shown in Figure 19 control
the speed range. As a general rule, smaller bits and
softer material require higher speeds and less torque,
and larger bits and harder materials require slower
speeds and greater torque.
To change the RPM, do these steps:
1. Turn the mill ON and rotate the RPM dial (Figure
18) to reach the desired speed.
Figure 18. RPM dial.
To change speed range, do these steps:
Motor Mount
1. Remove the pulley cover and loosen the motor
mount nuts shown in Figure 19.
Nuts
2. Slide the motor pulley toward the spindle pulley and
move the round belt to the other pulley position.
Note: The upper pulley position is the low range,
and the lower pulley position is the high range.
Figure 19. Spindle speed pulleys.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Drill Chuck
4" shank. When installing a bit in the drill chuck, make
The drill chuck will only accept bits with a maximum of
⁄
1
sure it is tight enough that it will not come loose during
operation.
To install a drill bit, do these steps:
1. UNPLUG THE MICRO MILL!
2. Open the drill chuck wide enough to accept the
shank of the bit.
3. Insert the bit as far as possible into the chuck
WITHOUT allowing the chuck jaws to touch the cut-
ting edges, and hand tighten the chuck.
Figure 20. Drill chuck.
Note: Make sure small bits are not trapped between
the edges of two jaws; if they are, reinstall the bit
or it will not be secure enough to use for drilling.
4. Final tighten the drill chuck with the chuck key.
To remove a drill bit, do these steps:
1. UNPLUG THE MICRO MILL!
2. Use the chuck key to open the drill chuck, and catch
the bit with a rag to protect your hands.
Drill Chuck Removal
The drill chuck and the collet chuck are attached to the
arbor with a JT1 taper. Matched tapers on the arbor and
the inside of the chuck use a friction fit to for a semi-per-
manent assembly.
Figure 21. Chuck removal wedge.
To remove the drill chuck, do these steps:
1. Protect the table surface with a piece of cardboard,
or hold the cutter or tool with a shop towel to pre-
vent it from falling out of the collet.
2. Place the chuck removal wedge (Figure 21) between
the top of the drill chuck and the spindle (see Figure
22), then tap the wedge to separate the chuck from
the arbor.
Figure 22. Drill chuck removal.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Collets
The collet chuck (an optional accessory) for the micro
mill offers increased precision and rigidity compared to
the drill chuck. Each collet will only fit tooling with a
specific shaft diameter. This collet set includes 1⁄4", 3⁄16",
5⁄32", 5⁄64", 3⁄64" collets.
To install the collet chuck, do these steps:
1. UNPLUG THE MICRO MILL!
2. Remove the drill chuck and clean the arbor and
collet chuck tapers with denatured alcohol.
3. Push the collet chuck onto the arbor.
Figure 23. Installing the collet chuck.
4. Place a piece of wood on the compound slide table
and use the downfeed lever to firmly press the
collet chuck against the piece of wood (see Figure
23) to seat the collet chuck on the arbor.
To install the collet in the collet chuck, do these steps:
1. Place the grooved end of the collet into the collet nut
until the off-center lip of the collet nut snaps into the
collet groove. See Figure 24.
Note: This lip and groove pulls the collet from the
spindle when the collet nut is removed.
Off-Center Collet Lip
and Collet Groove
2. Place the collet nut and collet into the collet chuck
and finger tighten the collet nut onto the collet
chuck.
Figure 24. Collet and collet nut lip.
3. Insert the bit into the collet, place a hex wrench
through the hole in the spindle, and tighten the
collet with a 22mm wrench (see Figure 25).
To remove a bit from the collet chuck, do these steps:
1. Protect the table surface with a piece of cardboard
or hold the cutter or tool with a shop towel to pre-
vent it from falling out of the collet.
2. Place a hex wrench through the hole in the spindle
and loosen the collet nut with a 22mm wrench until
the bit is free.
Figure 25. Installing a collet.
Note: Remove the collet chuck in the same manner as
removing the drill chuck.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
MAINTENANCE
General
Regular periodic maintenance on your SHOP FOX®
Model M1036 will ensure its optimum performance. Make
a habit of inspecting your machine each time you use it.
Check for the following conditions and repair or
replace when necessary:
•
•
•
•
•
•
•
Loose chucks and arbors.
Loose vises or clamps.
Loose mounting bolts.
Worn switch.
Worn or damaged cords and plugs.
Damaged round belt.
MAKE SURE that your machine is
unplugged during all maintenance pro-
cedures! If this warning is ignored, seri-
ous personal injury may occur.
Any other condition that could hamper the safe
operation of this machine.
A thorough cleaning, on a regular basis, will increase the
machine durability and efficiency by removing chips and
grime that can gum up moving parts.
A regular application of a protective spray coating will
keep the table and other bare metal parts from rusting
and pitting.
Cleaning
Cleaning the Model M1036 is relatively easy. Sweep or
vacuum excess metal chips from the table and ways, and
wipe off the remaining waste with a dry cloth. If any cut-
ting fluid is left on the table, wipe it up with a rag. Treat
all unpainted cast iron and steel with a non-staining lubri-
cant after cleaning.
Table & Base
Keep exposed cast iron rust-free with regular applications
of surface lubricants designed for cast iron such as G96®
Gun Treatment or SLIPIT®. For long term storage you may
want to consider products like Boeshield T-9™.
Remove vises, clamps, compound slide tables, etc. after
use so moisture cannot be trapped between the compo-
nents and cause rust.
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Lubrication
Regular lubrication will ensure your mill performs at its
highest potential.
Place two to three drops of ISO 68 or SAE 20W non-deter-
gent oil or similar lubricant directly on the following
areas each time you use your mill (see Figure 26):
•
•
Cross slide and saddle ways
Quill shaft
Apply a light weight lithium based grease directly to
these points once a month or more frequently as needed:
•
•
Longitudinal leadscrew (Figure 27)
Crossfeed leadscrew (Figure 28)
Figure 26. Points of lubrication.
Note: Pry up the leadscrew cover to access the crossfeed
leadscrew.
NOTICE
Lack of lubrication causes poor machine perfor-
mance. Keep your mill lubricated to reduce wear on
parts and discourage oxidation.
Figure 27. Longitudinal leadscrew.
Figure 28. Crossfeed leadscrew.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
SERVICE
General
This section covers the most common service adjustments
or procedures that may need to be made during the life
of your machine.
If you require additional machine service not included
in this section, please contact Woodstock International
Technical Support at (360) 734-3482 or send e-mail to:
Gibs
MAKE SURE that your machine is
unplugged during all service proce-
dures! If this warning is ignored, seri-
ous personal injury may occur.
The gibs are pre-adjusted at the factory and should not
need further adjustment until many hours of machine use,
if ever. If the movement seems too tight, make sure that
the locks are fully released, ways are free of chips and
debris and are thoroughly lubricated with oil.
When adjusting the gibs, the goal is to take out unneces-
sary play in the table without causing the slides to bind.
Loose gibs may cause poor finishes on the workpiece and
may cause undue wear on the slide. Over-tightening may
cause binding and premature wear to the gib.
Each gib has multiple lock nuts and set screws that need
to be adjusted. Make your adjustments equally and in
small increments.
To adjust the gibs, do these steps:
1. UNPLUG THE MICRO MILL!
Figure 29. Always unplug before servicing.
2. Loosen the lock nuts as shown in Figure 30.
3. Move the table back-and-forth, while slightly tight-
ening each set screw. When properly adjusted, the
gib should offer slight resistance without binding.
4. Tighten the lock nuts.
Figure 30. Longitudinal gib screw.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Replacing Motor Brushes
After some period of time, the carbon brushes on the
DC motor will need to be replaced. Always replace the
brushes in pairs.
To replace the motor brushes, do these steps:
1. UNPLUG THE MICRO MILL!
2. Remove the lower motor cover (see Figure 31) to
expose the motor.
3. Unscrew the cap from the motor housing (see Figure
32).
Figure 31. Lower motor cover.
4. Remove the spring and carbon brush, and replace
with a new spring and carbon brush.
5. Screw the cap back into the motor housing.
Carbon Brush
Cap
Fuse Replacement
A fuse is located in the switch housing near the RPM dial.
To replace the fuse, do these steps:
1. Loosen the fuse cap.
2. Remove and replace the fuse from the fuse cradle
(see Figure 33).
Figure 32. Carbon brush removal.
3. Replace the fuse cap.
Figure 33. Fuse replacement.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Electrical Components
Circuit
Board
Fuse
Box
On/OFF
Switch
Variable
Speed Switch
Wiring Diagram
�������������
�
�
�
�
��
��
��
���
��
��
��
����
��������
�����
������
������
������
�����
�
�
����������
������
������
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Troubleshooting
This section covers the most common problems and corrections with this type of
machine. WARNING! DO NOT make any adjustments until power is disconnected and
moving parts have come to a complete stop!
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Motor will not start.
1. Blown system fuse.
1. Replace fuse.
2. Tripped circuit breaker inside
power source breaker box.
3. Low voltage.
4. Open circuit in motor or loose
connections.
2. Reset circuit breaker by flipping switch on then off
then back on.
3. Check power supply for proper voltage.
4. Inspect all lead connections on motor and magnetic
switch for loose or open connections.
5. Replace switch.
5. Switch at fault.
Fuses or circuit breakers
trip open.
1. Short circuit in line cord or plug.
1. Inspect cord or plug for damaged insulation and
shorted wires and replace extension cord.
2. Inspect all connections on motor for loose or
shorted terminals or worn insulation.
2. Short circuit in motor or loose
connections.
3. Incorrect fuses or circuit breakers
in power supply.
3. Install correct fuses or circuit breakers.
Motor overheats.
1. Motor overloaded.
1. Reduce load on motor.
2. Air circulation through the motor
restricted.
2. Clean out motor to provide normal air circulation.
3. Motor brushes are wearing.
3. Inspect motor brushes, replace if necessary.
Bit slips in collet or drill
chuck.
1. Chuck is not fully tightened.
2. Bit installed in drill chuck off
center.
1. Tighten the collet or drill chuck.
2. Re-install bit in drill chuck.
3. Wrong size collet.
3. Measure tool shank diameter and match with
appropriate diameter collet.
4. Debris in collet or in spindle taper. 4. Remove all oil and debris from collet and spindle
taper.
5. Taking too big of a cut.
5. Lessen depth of cut and allow chips to clear.
Breaking tools or cutters.
Machine is loud when
cutting. Overheats or bogs 2. Dull cutting tools.
down in the cut.
1. RPM and or feed rate is too fast.
2. Cutting tool getting too hot.
3. Taking too big of a cut.
1. Reduce RPM and feed rates.
2. Use cutting fluid or oil for appropriate application.
3. Lessen depth of cut and allow chips to clear.
1. Excessive depth of cut.
1. Decrease depth of cut.
2. Use sharp cutting tools.
Workpiece vibrates or
1. Table locks not tight.
1. Tighten down table locks.
chatters during operation. 2. Workpiece not securely clamped to 2. Check that clamping is tight and sufficient for the
table or into mill vise.
3. RPM and feed rate too high.
job. Make sure mill vise is tight to the table.
3. Use appropriate RPM and feed for the job.
Table hard to move.
Bad surface finish.
1. Table locks are tightened down.
2. Chips have loaded up on bedways. 2. Frequently clean away chips that load up during
milling operations.
3. Bedways are dry and in need of
lubrication.
4. Gibs are too tight.
1. Make sure table locks are fully released.
3. Lubricate bedways and handles.
4. Loosen gib screw(s).
1. Wrong RPM or feed rate.
2. Dull cutting tool or poor cutting
tool selection.
1. Adjust for appropriate RPM and feed rate.
2. Sharpen cutting tool or select a better cutting tool
for the intended operation.
3. Table locks not tightened down.
4. Gibs are loose.
3. Tighten table locks to maintain rigidity.
4. Tighten gibs slightly.
Difficulty removing collet 1. Debris in spindle taper or collet
from spindle. taper or both.
1. Keep all taper surfaces spotlessly clean.
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
PARTS
�����
�����
����
�����
�����
��
��
����
��
��
��
����
����
��
�����
�����
����
����
��
�����
�����
�����
�����
����
�����
�����
�����
�����
�����
����
��
��
��
��
�����
�����
�����
��
��
�����
�����
�����
��
��
��
�����
�����
��
��
��
��
�����
��
��
��
�����
��
��
��
��
��
��
��
�����
����
��
��
��
��
�����
��
��
����
��
��
��
��
��
��
���
���
��
��
��
��
��
��
���
���
��
��
��
��
��
�
��
�
�
��
��
�
��
��
��
�
��
��
��
��
��
��
��
��
�
��
��
��
��
��
��
��
�
�
��
����
��
����
��
�
��
��
��
�
�
��
��
�
��
��
��
��
��
��
��
��
���
���
��
��
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Parts List
REF
1
2
3
4
5
6
7
8
PART�#
XPSS64M
XPR39M
DESCRIPTION
SET�SCREW�M6-1�X�14
EXT�RETAINING�RING�8MM
GEAR
SPECIAL�WASHER
PHLP�HD�SCR�M3-.5�X�6
ROUND�PIN�4�X�10
DIAL�RING
REF
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
69-1
69-2
70
71
72
73
74
PART�#
DESCRIPTION
SPACER
INT�RETAINING�RING�28MM
HUB
GEAR
XM1036039
XPR20M
XM1036003
XM1036004
XPS12M
XM1036006
XM1036007
XPSS31M
XM1036009
XM1036010
XM1036011
XPRP61M
XM1036041
XM1036042
XM1036043
XM1036044
XM1036045
XM1036046
XM1036047
XPFH49M
XM1036049
XM1036050
XM1036051
XM1036052
XM1036053
XPSB15M
XM1036055
XPR05M
XM1036057
XM1036058
XM1036059
XP6002
XM1036061
XM1036062
XM1036063
XM1036064
XM1036065
PSS34M
XM1036067
XPSB125M
XM1036069
XM1036069-1
XM1036069-2
XM1036070
XM1036071
XM1036072
XM1036073
XM1036074
COVER
ROUND�PIN�3�X�10
ELECTRICAL�BOX�(I)
FLAT�HD�SCR�M2-.4�X�6
CONNECTING�PLATE�(LEFT)
FLAT�HD�SCR�M3-.5�X�6
PLATE
DIGITAL�READ�OUT
CLUTCH�KNOB
CONNECTING�PLATE�(RIGHT)
RUBBER�WASHER
CAP�SCREW�M5-.8�X�20
DUST�PLATE
EXT�RETAINING�RING�15MM
SPINDLE�SLEEVE
INDUCTIVE�PLATE
SPINDLE
BALL�BEARING�6002
CHUCK�JT1
LOCK�RING
COMPRESSION�SPRING
RUBBER�FOOT
SPACER
SET�SCREW�M5-.8�X�16
FELT�DUSTER
CAP�SCREW�M3-.5�X�5
MOTOR
CARBON�MOTOR�BRUSH
BRUSH�CAP
BOTTOM�COVER
SPACER
RULER
SQUARE�NUT�M5-.8
SPANNER�NUT�M24-3�X�1.5
SET�SCREW�M5-.8�X�8
HANDLE�SEAT
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
HANDLE�SHAFT
HANDLE�KNOB�M8-1.25
ROLL�PIN�3�X�12
CAP�SCREW�M3-.5�X�14
SPRING�SEAT
WOUND�SPRING
SHAFT
SPACER
XPSB93M
XM1036014
XM1036015
XM1036016
XM1036017
XM1036018
XM1036019
XM1036020
XM1036021
XM1036022
XM1036023
XPW05M
XPLW02M
XPN04M
XM1036027
XM1036028
XPSS08M
XM1036030
XPS87M
XM1036032
XM1036033
XPB97M
XM1036035
XP6001
XM1036037
XPWRCRD110L
STRAIN�RELIEF
LOCK�KNOB
STUD�M8-1.25
FIXTURE�BLOCK�(I)
FIXTURE�BLOCK�(II)
HEAD�STOCK
FLAT�WASHER�4MM
LOCK�WASHER�4MM
HEX�NUT�M4-.7
LOCKING�PIN
SMALL�PULLEY
SET�SCREW�M4-.7�X�5
UPPER�COVER
PHLP�HD�SCR�M5-.8�X�45
ROUND�BELT
BIG�PULLEY
HEX�BOLT�M4-.7�X�12
BEARING�SEAT
BALL�BEARING�6001ZZ
SPACER
POWER�CORD
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
REF
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
PART�#
DESCRIPTION
FLAT�WASHER�24MM
BASE
COLUMN
CAP�SCREW�M5-.8�X�12
PARALLEL�BAR
SET�SCREW�M5-.8�X�6
SMALL�WHEEL
SPACER
REF
99-10 XPW02M
PART�#
DESCRIPTION
FLAT�WASHER�5MM
END�COVER
HEX�NUT�M5-.8
POSITION�GUAGE
RIVET
LONGITUDINAL�LEADSCREW�NUT
CAP�SCREW�M3-.5�X�8
LONGITUDINAL�WEDGE
CAP�SCREW�M4-.7�X�12
SET�SCREW�M4-.7�X�12
HEX�NUT�M4-.7
XM1036075
XM1036076
XM1036077
XPSB33M
XM1036079
XPSS26M
XM1036081
XM1036082
XM1036083
XPSS08M
99-11 XM1036099-11
99-12 XPN06M�
99-13 XM1036099-13
99-14 XM1036099-14
99-15 XM1036099-15
99-16 XPSB80M
99-17 XM1036099-17
99-18 XPSB23M
99-19 XPSS22M
WORM�SHAFT
SET�SCREW�M4-.7�X�5
FLAT�WASHER�4MM
ELECTRICAL�BOX�BASE
FLAT�HD�SCR�M3-.5�X�8
PHLP�HD�SCR�M3-.5�X�6
POWER�SWITCH
MACHINE�ID�LABEL
TAP�SCREW�M3-.5�X�6
VARIABLE�SPEED�CONTROL�KNOB
FUSE�BOX
XPW05M
99-20 XPN04M
XM1036086
XM1036087
XPS12M
99-21 XM1036099-21
99-22 XM1036099-22
99-23 XPSB39M
INDICATOR�PLATE
CROSS�WEDGE
CAP�SCREW�M4-.7�X�20
SET�SCREW�M4-.7�X�20
CROSS�LEADSCREW�NUT
CROSS�LEADSCREW
FRONT�SUPPORTING�SEAT
BASE
SUPPORT�SEAT
COVER�1
COVER�2
LONGITUDINAL�LEADSCREW
SADDLE
XM1036089
XM1036090
XM1036091
XM1036092
XM1036093
XM1036094
XM1036095
XLABEL04
XM1036097
XM1036098
XM1036099
XM1036099-1
XM1036099-2
XPSS26M
XM1036099-4
XM1036099-5
XPSB18M
XM1036099-7
XM1036099-8
XM1036099-9
99-24 XPSS50M
99-25 XM1036099-25
99-26 XM1036099-26
99-27 XM1036099-27
99-28 XM1036099-28
99-29 XM1036099-29
99-30 XM1036099-30
99-31 XM1036099-31
99-32 XM1036099-32
99-33 XM1036099-33
99-34 XM1036099-34
99-35 XPSS45M
PC�BOARD
WARNING�LABEL
ELECTRICITY�LABEL
SHOP�FOX�LOGO�LABEL
WARNING�ICON�LABEL
COMPOUND�SLIDE�ASSEMBLY
HANDLE�SCREW�M4-.7�X�8
HANDLE
SET�SCREW�M5-.8�X�6
HANDWHEEL
FLAT�SPRING
99
DIAL
99-1
99-2
99-3
99-4
99-5
99-6
99-7
99-8
99-9
SET�SCREW�M3-.5�X�6
GRADUATED�DIAL
DOUBLE�END�WRENCH�5.5�X�7MM
#2�PHILLIPS�SCREWDRIVER
HEX�WRENCH�2MM
HEX�WRENCH�2.5MM
HEX�WRENCH�3MM
HEX�WRENCH�4MM
99-36 XM1036099-36
102
103
104
105
106
107
XM1036102
XPSDP2
XPAW02M
XPAW02.5M
XPAW03M
XPAW04M
CAP�SCREW�M4-.7�X�8
RIGHT�SUPPORT�SEAT
WORKTABLE
LEADSCREW�SUPPORT�SEAT
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work-
manship and materials for a period of two years from the date of original purchase by the original
owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence
or accidents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX®
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair
facility designated by our Bellingham, WA office, with proof of their purchase of the product within
two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect resulted from
causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must
bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durabil-
ity standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
M1036 Micro Mill
Warranty Registration
Name___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________State___________________________Zip________________________
Phone #______________________Email __________________________Invoice #___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
_____ Advertisement
____ Friend
____ Website
____ Local Store
____ Other:
_____ Mail Order Catalog
2. How long have you been a woodworker/metalworker?
_____ 0-2 Years _____ 2-8 Years ____8-20 Years
_____ 20+ Years
3. How many of your machines or tools are Shop Fox®?
_____ 0-2 _____ 3-5 ____6-9
_____ 10+
____ No
____ No
4. Do you think your machine represents a good value?
_____ Yes
5. Would you recommend Shop Fox® products to a friend? _____ Yes
6. What is your age group?
_____ 20-29
_____ 50-59
____ 30-39
____ 60-69
____ 40-49
____ 70+
7. What is your annual household income?
_____ $20,000-$29,000
_____ $50,000-$59,000
____ $30,000-$39,000
____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
8. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Old House Journal
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Shotgun News
9. Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|