Woodstock Staple Gun W1778 User Manual

MODEL W1778  
18 GAUGE DEEP  
STAPLER KIT  
OWNER'S MANUAL  
Phone: (360) 734-3482 • Online Technical Support: [email protected]  
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC.  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT  
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.  
#9569BL Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
SAFETY  
For Your Own Safety Read Instruction Manual  
Before Operating This Equipment  
The purpose of safety symbols is to attract your attention to possible hazardous  
conditions. This manual uses a series of symbols and signal words which are intended  
to convey the level of importance of the safety messages. The progression of  
symbols is described below. Remember that safety messages by themselves do not  
eliminate danger and are not a substitute for proper accident prevention measures.  
Indicates an imminently hazardous situation which, if  
not avoided, WILL result in death or serious injury.  
Indicates a potentially hazardous situation which, if  
not avoided, COULD result in death or serious injury.  
Indicates a potentially hazardous situation which, if  
not avoided, MAY result in minor or moderate injury.  
It may also be used to alert against unsafe practices.  
This symbol is used to alert the user to useful  
information about proper operation of the  
equipment.  
NOTICE  
Safety Instructions for Pneumatic Tools  
5. KEEP CHILDREN AND VISITORS  
AWAY. All children and visitors  
should be kept at a safe distance  
from work area.  
1. KEEP ALL SAFETY DEVICES IN  
PLACE and in working order.  
2. REMOVE ADJUSTING KEYS AND  
WRENCHES. Form habit of checking  
to see that keys and adjusting  
wrenches are removed from tool  
before operation.  
6. MAKE WORKSHOP CHILD PROOF by  
locking your shop and shutting off  
air valves.  
7. DO NOT FORCE TOOL. It will do  
the job better and safer at the rate  
for which it was designed.  
3. KEEP WORK AREA CLEAN. Cluttered  
areas and benches invite accidents.  
4. DO NOT USE IN DANGEROUS  
ENVIRONMENT. Do not use  
8. USE THE RIGHT TOOL. Do not  
force tool or attachment to do a  
job for which it was not designed.  
pneumatic tools in damp or wet  
locations, or where any flammable  
or noxious fumes may exist. Keep  
work area well lighted.  
9. DO NOT USE UNDER THE  
INFLUENCE OF DRUGS OR  
ALCOHOL.  
-1-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
Safety Instructions for Pneumatic Tools  
17. DISCONNECT TOOLS before  
servicing, changing accessories, or  
moving to another location.  
10. USE PROPER AIR HOSE for the  
tool. Make sure your air hose is in  
good condition and is long enough  
to reach your work without  
stretching.  
18. DO NOT OVERREACH. Keep proper  
footing/balance at all times.  
11. WEAR PROPER APPAREL. Do  
not wear loose clothing, gloves,  
neckties, rings, bracelets, or  
other jewelry which may get  
caught in moving parts. Non-slip  
footwear is recommended. Wear a  
protective hair covering to contain  
long hair.  
19. USE THE RECOMMENDED  
ACCESSORIES. Consult owner’s  
manual for recommended  
accessories. The use of improper  
accessories may cause risk of  
injury.  
20. CHECK FOR DAMAGED PARTS  
BEFORE USING. Check for binding  
and alignment of parts, broken  
parts, part mounting, loose bolts,  
and any other conditions that  
mayaffect machine operation.  
Repair or replace damaged parts.  
12. ALWAYS USE SAFETY GLASSES.  
Also use a face or dust mask  
if cutting operation is dusty.  
Everyday eyeglasses only have  
impact resistant lenses, they are  
NOT safety glasses.  
21. NEVER LEAVE UNATTENDED TOOL  
CONNECTED TO AIR. Disconnect  
the air hose and do not leave tool  
until it is relieved of any built up  
pressure.  
13. WEAR APPROVED HEARING  
PROTECTION. Air escaping from  
pneumatic tools can exceed safe  
exposure limits and may cause  
hearing damage with prolonged  
exposure.  
22. NEVER ALLOW UNTRAINED  
USERS TO USE THIS TOOL WHILE  
UNSUPERVISED.  
14. SECURE WORK. Use clamps or a  
vise to hold work when practical.  
It is safer than using your hand  
and frees both hands to operate  
tool.  
23. IF YOU ARE UNSURE OF THE  
INTENDED OPERATION, STOP  
USING TOOL. Seek formal training  
or research books or magazines  
that specialize in pneumatic tools.  
15. MAINTAIN TOOLS WITH CARE.  
Keep tools lubricated and clean  
for best and safest performance.  
Follow instructions for lubricating  
and changing accessories.  
24. BE AWARE OF HOSE LOCATION  
WHEN USING PNEUMATIC TOOLS.  
Hoses can easily become a tripping  
hazard when laid across the floor  
or spread out in a disorganized  
fashion.  
16. REDUCE THE RISK OF  
UNINTENTIONAL FIRING. Do not  
carry tool with hand on trigger  
and always disconnect from air  
when not in use.  
-2-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
Additional Safety Instructions for Staplers  
1. HAND INJURIES: Do not place  
your hands near the staple point  
of entry. A staple can deflect and  
tear through the surface of the  
workpiece, puncturing your hand or  
fingers.  
5. HOSE USAGE: Make sure your air  
hose is designed for the tool in  
use, is in good condition, and is  
long enough to reach your work  
without stretching. However, an  
overly long air hose in the work  
area may be a tripping hazard.  
2. COMBUSTIBLE GASES: Never  
connect the stapler to pressurized  
oxygen or other combustible  
gases as a power source. Only use  
filtered, lubricated, and regulated  
compressed air.  
6. OPERATING QUESTIONS: If you  
are not sure about the intended  
operation, stop using the stapler.  
Seek formal training.  
7. MAINTENANCE: Always disconnect  
air from the stapler when servicing  
or installing staples. During  
3. SAFE HANDLING: Never point the  
stapler at others! Do not keep  
the trigger pulled when loading  
fasteners, carrying, or holding  
tool. Carry the stapler only by the  
handle, never by any other part.  
Do not carry the stapler by the air  
hose. Disconnect the stapler from  
the air hose when going up and  
down ladders.  
maintenance, a stapler connected  
to air may fire accidentally,  
causing serious personal injury.  
8. COMPRESSED AIR RATING: Do not  
connect the stapler to compressed  
air that exceeds 120 PSI.  
9. CHECK VALVE: Do not use a check  
valve or any other fitting that  
4. CLEANING: Never use gasoline or  
other flammable liquids to clean  
the stapler; vapors in the stapler  
will ignite by a spark and cause it  
to explode.  
allows air to remain in the tool.  
10. MODIFICATION: Do not modify  
this tool or bypass the safety nose  
mechanism.  
Never point this stapler at yourself  
or another person! Always pay  
attention to the direction this stapler  
is pointed. Use this tool with respect  
and caution to lessen the possibility  
of operator or bystander injury.  
Ignoring this warning may result in  
serious personal injury.  
Stapler accidents routinely happen  
while moving the gun to another  
location, such as up ladders, to  
another room, or even another job  
site. Always disconnect the gun  
immediately after use and never  
transport the gun while connected to  
the air—even if the air compressor is  
disconnected from its power source!  
-3-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
INTRODUCTION  
Woodstock Technical  
Tool Data  
Staple Size .......................... 18 Gauge  
Staple Length........................ 58"-158  
Staple Crown ...............................14  
Magazine Capacity...............100 Staples  
Air Inlet.................................¼" NPT  
Weight................................. 3.2 lbs.  
Operating Pressure ...............70-100 PSI  
Support  
"
"
This tool has been specially designed  
to provide many years of trouble-free  
service. Close attention to detail,  
ruggedly built parts and a rigid quality  
control program assure safe and reliable  
operation.  
Woodstock International, Inc. is  
committed to customer satisfaction.  
Our intent with this manual is to include  
the basic information for safety, setup,  
operation, maintenance, and service of  
this product.  
We stand behind our tools! In the  
event that questions arise about  
your tool, please contact Woodstock  
International Technical Support at  
(360) 734-3482 or send e-mail to:  
knowledgeable staff will help you  
troubleshoot problems and process  
warranty claims.  
Read the manual before operation.  
Become familiar with this stapler, its  
safety instructions, and its operation  
before beginning any work. Serious  
personal injury may result if safety  
or operational information is not  
understood or followed.  
If you need the latest edition of this  
manual, you can download it from  
If you have comments about this  
manual, please contact us at:  
No list of safety guidelines can be  
complete. Every shop environment  
is different. Always consider safety  
first, as it applies to your individual  
working conditions. Use this and  
other tools with caution and respect.  
Failure to do so could result in serious  
personal injury, damage to equipment  
or poor work results.  
Woodstock International, Inc.  
Attn: Technical Documentation  
Manager  
P.O. Box 2309  
Bellingham, WA 98227  
-4-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
Compressed Air System  
The Model W1778 is designed to be  
operated at 70-100 PSI using clean,  
dry, regulated, compressed air. Do not  
exceed the 120 PSI maximum operating  
pressure for your model.  
Before using your new stapler, regulate  
the air pressure to find the optimum  
setting within the specified operating  
range. Start by testing the stapler at  
a low setting, then increase the air  
pressure as needed for satisfactory  
results.  
Exceeding the maximum permissible  
operating pressure may damage the  
stapler and cause it to malfunction.  
To protect yourself from personal  
injury, DONOTallowtheairpressure  
to exceed the recommended  
pressure for this stapler!  
An in-line filter/lubricator/regulator unit,  
can be installed as depicted in Figure 1.  
This filter/lubricator/regulator unit  
will protect your tool from damaging  
water build-up, allow you to adjust and  
maintain regulated air pressure to your  
tool, and save you the inconvenience of  
having to manually lubricate your tool  
every time you use it.  
If you plan on installing a filter/  
lubricator/regulator unit in your  
compressed air system, always follow the  
connection instructions that come with  
the unit.  
 
��  
�  
���  
�  
�  
�  
���  
�  
���  
�  
�  
�  
�  
�  
�  
Figure 1. Typical filter/lubricator/regulator installation order.  
-5-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
SETUP  
Unpacking  
This tool has been carefully packaged for safe transportation. If you notice the tool  
has been damaged during shipping, please contact your authorized Shop Fox dealer  
immediately.  
Inventory  
The following is a description of the main components shipped with the Model W1778.  
Lay the components out to inventory them.  
Note: If you can't find an item on this list, check the mounting location on the tool  
or examine the packaging materials carefully. Occasionally we pre-install certain  
components for safer shipping.  
Box Inventory (Figure 2)  
Qty  
Qty  
E. Hex Wrench 4mm ....................... 1  
F. Pneumatic Tool Oil ..................... 1  
A. Safety Goggles .......................... 1  
B. 18 Gauge Deep Stapler................. 1  
C. Carrying Case............................ 1  
D. Hex Wrench 3mm ....................... 1  
A
C
E
B
F
D
Figure 2. Model W1778 inventory.  
-6-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
— If the stapler fires when the trig-  
ger is pulled, without the safety  
nose mechanism being depressed,  
then the stapler is not working  
properly.  
Safety Nose Mechanism  
A safety mechanism on the nose of  
the stapler protects against accidental  
firing. When the trigger is pressed, the  
stapler will not fire until the safety nose  
mechanism is depressed.  
— If you find that the safety nose  
mechanism is not working prop-  
erly, check the lubrication of its  
sliding components.  
Before you use your stapler for the first  
time, check the safety nose mechanism  
to ensure proper function.  
To check the safety nose mechanism,  
do these steps:  
Do not attempt to modify or bypass  
the safety nose mechanism to make  
the stapler fire without pushing the  
nose down.  
1. DISCONNECT STAPLER FROM THE AIR  
SUPPLY!  
2. Make sure the magazine is empty and  
contains no staples.  
3. Make sure the trigger and the safety  
nose mechanism move up and down  
without sticking.  
The safety mechanism is a mechanical  
device that can fail. Never rely on this  
mechanism as an excuse to point the  
stapler at yourself or any bystanders.  
Serious injury may occur.  
4. Connect the stapler to the air supply.  
5. Without pressing the trigger,  
depress the safety nose mechanism  
against a scrap piece of wood that is  
clean and free of any knots, staples,  
or other foreign objects.  
— If the stapler does not fire, then  
the safety nose mechanism is  
working correctly.  
Operating this stapler can propel  
objectsintotheair,causingimmediate  
eye damage. To protect yourself,  
always wear ANSI approved safety  
glasses or goggles when operating this  
equipment.  
— If the stapler does fire when you  
do this, immediately disconnect  
the stapler from the air supply and  
call Technical Support.  
-7-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
OPERATIONS  
Loading  
When replacing staples in your Model  
W1778, follow these guidelines:  
Pusher  
Gauge:........................................18  
Length: ............................. 58" – 158  
"
Capacity:................................... 100  
Crown:.......................................14  
"
Magazine  
To load your stapler, do these steps:  
Figure 4. Loading staples into magazine.  
1. DISCONNECT STAPLER FROM THE AIR  
Operating  
SUPPLY!  
If you have not read the safety  
instructions in this manual, do not  
operate the stapler.  
2. Grip the stapler firmly, unlock the  
catch lever (Figure 3) and pull the  
magazine pusher back  
Before you operate your stapler, place  
two to three drops of the included  
pneumatic tool oil into the quick connect  
fitting where the stapler connects to the  
air supply, unless using a lubricator unit.  
Pusher  
To operate your stapler, do these steps:  
Catch Lever  
1. Connect the air supply to the quick  
connect fitting.  
Figure 3. Sliding magazine pusher back  
2. To test for proper staple penetration,  
hold the stapler perpendicular to  
the surface of a piece of clean scrap  
wood that is thick enough for the  
length of staples you have loaded.  
and engaging catch lever.  
3. Point the stapler up and insert a stick  
of staples, pointed-end up, into the  
bottom of the magazine, as shown in  
Figure 4. Make sure that the pointed  
ends of the staples point in the same  
direction as the stapler nose piece.  
3. Depress the safety nose mechanism  
against your workpiece.  
4. Slide the staples all the way down to  
4. Before pulling the trigger, make sure  
your free hand and other body parts  
are positioned out of the way of a  
potential path of a staple in case of  
deflection.  
the nose of the stapler.  
5. Slide the magazine pusher toward the  
nose of the stapler until the catch  
lever locks.  
-8-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
Single Fire Operation  
The stapler is designed to fire one staple  
DO NOT place your hands near the  
staple point of entry. A staple can  
deflect and tear through the surface  
of the workpiece, puncturing your  
hand or fingers.  
at a time.  
To operate your stapler in single fire  
mode, do these steps:  
1. Depress the safety nose mechanism  
against the workpiece.  
Deflection is caused when grain  
irregularities, knots or foreign objects  
inside the wood cause the staple  
to change its path, resulting in the  
staple puncturing the surface of the  
workpiece, as shown in Figure 5.  
2. Pull the trigger, then release the  
trigger after the staple is driven.  
Clearing Jammed  
Staples  
Besides damaging your workpiece,  
deflection can cause injury if your  
free hand is securing the workpiece in  
the location that the staple deflects.  
A jammed staple must be cleared before  
using the stapler again.  
To clear a jammed staple from the dis-  
charge area, do these steps:  
1. DISCONNECT STAPLER FROM THE AIR  
SUPPLY!  
2. Unlock the catch lever and slide the  
magazine pusher all the way back.  
3. Remove the staple stick from the  
magazine.  
Figure 5. Example of staple deflection.  
5. Pull the trigger.  
4. Flip the quick release latch, as shown  
in Figure 6, and open the cover.  
— If the staple drove into the wood  
far enough, continue with your  
intended operations.  
Cover  
Discharge  
Area  
— If the staple either went too far  
or not far enough, then adjust the  
air pressure. More air pressure  
will increase staple depth, less  
air pressure will decrease staple  
depth.  
Quick  
Release  
Latch  
Figure 6. Nose opened to clear a jam.  
5. The jammed staple should now be  
visible; remove it from the discharge  
area with needle nose pliers.  
-9-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
6. Secure the quick release latch.  
4. Remove the cap.  
7. Inspect the staple stick. If it is bent  
or damaged, throw it away and insert  
a new stick that only contains clean,  
undamaged staples. DO NOT use dirty  
or damaged staples!  
5. The top of the piston should now be  
visible inside the cylinder, which is  
housed in the head of the stapler.  
6. Open the nose cover as if to clear a  
jammed staple.  
8. Slide the magazine forward until the  
catch lever engages.  
7. Watch the discharge area and push  
the top of the piston with your  
finger. You will see the piston shaft  
slide down the discharge area.  
Replacing Pistons/  
O-Rings  
Under heavy use, a piston or piston shaft  
may wear out. Replacement is quick and  
easy. Contact your authorized Shop Fox  
dealer to obtain the Piston Repair Kit  
(part number X1778002).  
8. Taking care not to scratch or dent the  
stapler parts, use a wooden dowel  
or similarly shaped tool to push the  
piston shaft back inside the stapler  
until you can grip the piston head and  
remove it from the cylinder. Clean  
and inspect the parts for cracks,  
wear, or burrs.  
9. Place a new O-ring on the new piston  
and apply a thin film of the stapler  
lubricating oil on the O-ring.  
10. Insert the new piston in the cylinder.  
Make sure that the grooves on the  
piston shaft line up with those on the  
guide at the bottom of the cylinder.  
The new piston should easily slide  
into the cylinder. DO NOT force the  
piston into the cylinder! If the piston  
is not easily inserted, double-check  
the alignment of the piston shaft with  
the grooves on the guide.  
Always disconnect stapler from  
air whenever servicing! During  
maintenance, a stapler connected  
to air may fire accidentally, causing  
serious personal injury!  
To replace a piston, do these steps:  
11. After the piston is inserted correctly,  
close the magazine. Replace the rear  
cap assembly and tighten the four  
cap screws.  
1. DISCONNECT STAPLER FROM THE AIR  
SUPPLY!  
2. Remove all staples from the  
magazine cartridge, and clean the  
exterior of the stapler.  
12. For more assistance, or to install a  
complete O-ring set, refer to the  
appropriate breakdown diagram in  
the back of this manual for O-ring  
locations.  
3. Remove the four cap screws on the  
back of the stapler, near the exhaust  
port.  
-10-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
CLEANING & LUBRICATION  
Cleaning  
Lubricating  
Disconnect the stapler from the air  
supply before cleaning. Use a good  
solvent to clean the nose assembly of the  
stapler. Always be sure that the stapler is  
dry before using it again.  
Standard pneumatic tool oil has been  
included with your new Shop Fox stapler  
to help maintain its useful life. Place two  
to three drops of oil in the stapler air  
inlet (as shown in Figure 7) before every  
use, or after 2 hours of continuous use.  
Do not allow dust, chips, sand, etc.  
into the air connectors or into the body  
of the stapler; this may result in leaks  
and damage to the stapler and the air  
couplings.  
Figure 7. Lubricating stapler via air inlet.  
Wipe off any excess oil near the stapler  
exhaust to avoid dust build-up. When the  
oil that was included with the stapler has  
been completely used, replace with a  
quality pneumatic tool oil.  
An alternative to manual oiling is to  
install a lubricator in your air compressor  
line. A lubricator eliminates the need to  
oil your tool each time you use it. If you  
have a lubricator in your air compressor  
line, ensure it is functioning properly.  
Never use gasoline or other  
flammable liquids to clean this  
tool. Vapors in the tool may ignite,  
causing the tool to explode. Ignoring  
this warning may lead to serious  
personal injury or even death!  
-11-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
PARTS BREAKDOWN  
�  
�  
�  
�  
�  
��  
 
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
��  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
��  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
��  
�  
�  
��  
�  
�  
�  
�  
�  
�  
�  
�  
��  
�  
�  
-12-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
PARTS LIST  
REF PART# DESCRIPTION  
REF PART# DESCRIPTION  
1
2
3
4
5
6
7
8
XPLW01M LOCKWASHER5MM  
X1778002 PISTONREPAIRKIT  
X1778003 CARRYINGCASE  
XPAW04M HEXWRENCH4MM  
XPAW03M HEXWRENCH3MM  
X1778006 AIRPLUGCOVER  
X1775007 1/4"NPTMALECONNECT  
X1778008 ENDCAP  
X1778009 O-RING36.3x3.55  
X1778010 RUBBERHANDLE  
X1778011 LOCKNUTM4-.7  
X1778012 SUPPORTSEAT  
XPSB16M CAPSCREWM4-.7X16  
X1778014 TORSIONSPRING  
X1778015 CATCHLEVER  
X1778016 PIN3X25  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
X1778040 NOSEHEAD  
X1778041 SAFETYSTANDBRACKET  
X1778042 COMPRESSIONSPRING  
X1778043 SAFETYSTAND  
X1778044 ROLLPIN2.8X16  
X1778045 SAFETYSPACER  
X1778046 TRIGGER  
X1778047 PIN2.8X30  
9
X1778048 COMPRESSIONSPRING  
X1778049 O-RING11X1.85  
X1778050 TRIGGERVALVEGUIDE  
X1778051 O-RING2.9X1.75  
X1778052 TRIGGERVALVESTEM  
X1778053 TRIGGERVALVESEAT  
X1778054 RECTANGULARWASHER  
X1778055 RUBBERWASHER  
X1778056 GUNBODY  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
X1778017 FIXEDSEAT  
XPRP43M ROLLPIN3X22  
XPRP02M ROLLPIN3X16  
X1778020 BAFFLE  
XPSB110M CAPSCREWM4-.7X6  
X1778022 FIXEDSEAT  
X1778023 COMPRESSIONSPRING  
X1778024 PUSHERPIPE  
X1778025 PUSHER  
X1778026 FIXEDBLOCK  
X1778027 MAGAZINEPUSHER  
X1778028 MAGAZINE  
XPSB16M CAPSCREWM4-.7X16  
X1778030 MAGAZINEPUSHERCOVER  
XPEC01M E-CLIP3MM  
X1778032 PIN3X18  
X1778033 PIN3X18  
X1778034 NOSECOVER  
X1778035 QUICKRELEASELATCH  
X1778036 QUICKRELEASEHANDLE  
X1778037 DRIVERGUIDE  
XPRP15M ROLLPIN3X8  
X1778039 BAFFLE  
X1778057 BUMPER  
X1778058 PISTONASSEMBLY  
X1778059 O-RING21X2.5  
X1778060 CYLINDER  
X1778061 O-RING42.6x2.35  
X1778062 O-RING30x1.8  
X1778063 COLLAR  
X1778064 SEALINGGASKET  
X1778065 O-RING26X3  
X1778066 O-RING31X2  
X1778067 SWITCHVALVEPISTON  
X1778068 COMPRESSIONSPRING  
X1778069 SEALINGWASHER  
X1778070 O-RING14X2  
X1778071 CYLINDERCOVER  
XPW02M  
FLATWASHER5MM  
XPSB15M CAPSCREWM5-.8X20  
X1778074 AIRDEFLECTOR  
X1778075 COMPRESSIONSPRING  
X1778076 SPECIALCAPSCRM6-1X5  
X1778077 SAFETYGLASSES  
X1778078 COMPLETEO-RINGSET  
-13-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1778 18 Gauge Deep Stapler Kit  
Troubleshooting  
Symptom  
Possible Cause  
Solution  
1. O-rings must be replaced  
& operation of safety nose  
must be checked.  
Air leaking at  
1. O-rings in trigger valve  
housing are damaged.  
trigger valve area.  
Air leaking  
between housing  
and hose.  
1. Loose screws in housing.  
2. Damaged O-ring.  
3. Loose air fitting.  
1. Reseal and tighten screws.  
2. Replace O-ring  
3. Tighten air fitting & use  
teflon tape.  
Air leaking  
1. Damaged seal.  
1. Replace damaged seals.  
between housing  
and cap.  
Tool skips staples  
while discharging.  
1. Excessive air pressure.  
2. Air leaks.  
1. Reduce air pressure to  
tool.  
2. Reseal and tighten screws  
and fittings.  
3. Dirt in nose.  
3. Clean nose.  
4. Dirt or damage prevents  
staples from moving freely.  
5. Inadequate air flow to tool.  
4. Clean magazine and  
inspect/repair damage.  
5. Check fittings, hose,  
compressor, and air  
pressure.  
6. Replace O-ring and  
lubricate.  
6. Worn piston O-ring or lack of  
lubrication.  
7. Damaged trigger valve O-  
rings.  
7. Replace trigger valve O-  
rings.  
8. Worn bumper.  
9. Cap seal leaking.  
8. Replace bumper.  
9. Replace cap seal.  
Tool runs slowly  
or has a loss of  
power.  
1. Undersized air hose.  
2. Stapler is not lubricated.  
3. Broken spring in cap  
assembly.  
1. Use a larger hose.  
2. Lubricate stapler.  
3. Replace spring.  
4. Exhaust port in cap is  
blocked.  
4. Clean or replace damaged  
internal parts.  
Fasteners  
1. Staples are the wrong size.  
1. Use correct staples.  
2. Use undamaged, clean  
staples.  
frequently jam the 2. Staples are bent or dirty.  
stapler.  
3. Magazine or nose screws are  
loose.  
4. Driver or driver guide are  
worn or damaged.  
3. Tighten magazine.  
4. Replace worn or damaged  
parts.  
Stapler does not  
fire.  
1. Stapler is not lubricated.  
1. Follow lubricating  
instructions.  
2. Staple is jammed in magazine 2. Clear stapler magazine or  
or discharge area.  
3. Piston shaft is damaged.  
4. Air pressure too low.  
discharge area.  
3. Replace piston shaft.  
4. Check/increase air  
pressure.  
-14-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY AND RETURNS  
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects  
from workmanship and materials for a period of two years from the date of original  
purchase by the original owner. This warranty does not apply to defects due directly  
or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or  
reimbursement of third party expenses incurred.  
Woodstock International, Inc. will repair or replace, at its expense and at its option,  
the Shop Fox machine or machine part which in normal use has proven to be defective,  
provided that the original owner returns the product prepaid to a Shop Fox factory  
service center with proof of their purchase of the product within two years, and  
provides Woodstock International, Inc. reasonable opportunity to verify the alleged  
defect through inspection. If it is determined there is no defect, or that the defect  
resulted from causes not within the scope of Woodstock International Inc.'s warranty,  
then the original owner must bear the cost of storing and returning the product.  
This is Woodstock International, Inc.'s sole written warranty and any and all warranties  
that may be implied by law, including any merchantability or fitness, for any particular  
purpose, are hereby limited to the duration of this written warranty. We do not  
warrant that Shop Fox machinery complies with the provisions of any law or acts. In  
no event shall Woodstock International, Inc.'s liability under this warranty exceed the  
purchase price paid for the product, and any legal actions brought against Woodstock  
International, Inc. shall be tried in the State of Washington, County of Whatcom. We  
shall in no event be liable for death, injuries to persons or property or for incidental,  
contingent, special or consequential damages arising from the use of our products.  
Every effort has been made to ensure that all Shop Fox machinery meets high quality  
and durability standards. We reserve the right to change specifications at any time  
because of our commitment to continuously improve the quality of our products.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty Registration  
Name___________________________________________________________________________________  
Street __________________________________________________________________________________  
City _________________________State___________________________Zip________________________  
Phone #______________________Email __________________________Invoice #___________________  
Model #_________Serial #______________Dealer Name__________________Purchase Date___________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help us  
develop better products and services. Of course, all information is strictly confidential.  
1. How did you learn about us?  
_____ Advertisement  
____ Friend  
____ Website  
____ Local Store  
____ Other:  
_____ Mail Order Catalog  
2. How long have you been a woodworker/metalworker?  
_____ 0-2 Years  
_____ 2-8 Years  
____8-20 Years  
_____ 20+ Years  
3. How many of your machines or tools are Shop Fox?  
_____ 0-2 _____ 3-5  
____6-9  
_____ 10+  
____ No  
____ No  
4. Do you think your machine represents a good value?  
_____ Yes  
5. Would you recommend Shop Fox products to a friend? _____ Yes  
6. What is your age group?  
_____ 20-29  
_____ 50-59  
____ 30-39  
____ 60-69  
____ 40-49  
____ 70+  
7. What is your annual household income?  
_____ $20,000-$29,000  
_____ $50,000-$59,000  
____ $30,000-$39,000  
____ $60,000-$69,000  
____ $40,000-$49,000  
____ $70,000+  
8. Which of the following magazines do you subscribe to?  
____ Cabinet Maker  
____ Family Handyman  
____ Hand Loader  
____ Popular Mechanics  
____ Popular Science  
____ Popular Woodworking  
____ Practical Homeowner  
____ Precision Shooter  
____ Projects in Metal  
____ RC Modeler  
____ Today’s Homeowner  
____ Wood  
____ Wooden Boat  
____ Woodshop News  
____ Woodsmith  
____ Handy  
____ Home Shop Machinist  
____ Journal of Light Cont.  
____ Live Steam  
____ Model Airplane News  
____ Modeltec  
____ Old House Journal  
____ Woodwork  
____ Woodworker West  
____ Woodworker’s Journal  
____ Other:  
____ Rifle  
____ Shop Notes  
____ Shotgun News  
9. Comments:__________________________________________________________________  
_____________________________________________________________________________  
_____________________________________________________________________________  
_____________________________________________________________________________  
___________________________________________________________________  
___________________________________________________________________  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOLD ALONG DOTTED LINE  
Place  
Stamp  
Here  
WOODSTOCK INTERNATIONAL INC.  
P.O. BOX 2309  
BELLINGHAM, WA 98227-2309  
FOLD ALONG DOTTED LINE  
TAPE ALONG EDGES--PLEASE DO NOT STAPLE  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Whirlpool Dishwasher W10682797A User Manual
Whistler Power Supply 1200 WATT User Manual
WiLife Security Camera V 15 User Manual
Winegard Stereo System HD 8200P User Manual
Xerox Printer 100MX User Manual
Yamaha Car Stereo System Las Vegas CD32 User Manual
Zanussi Microwave Oven 20 GN 2 1 User Manual
Zanussi Ventilation Hood 642014 User Manual
Zanussi Washer ZWF 1217 W User Manual
Zhone Technologies Network Router 1611 A2 xxx User Manual