MODEL W1679
6" Jointer
INSTRUCTION MANUAL
COPYRIGHT © JULY, 2002 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Of Contents
PAGE
1.
2.
INTRODUCTION..............................................................................................2
About Your New Jointer ............................................................................2
Woodstock Service And Support ..................................................................2
Warranty And Returns................................................................................3
Machine Specifications ..............................................................................3
SAFETY ......................................................................................................4
Standard Safety Instructions ....................................................................4-5
Jointer Safety ..........................................................................................6
Avoiding Potential Injuries ..........................................................................7
110V Operation........................................................................................8
Extension Cords........................................................................................8
Grounding ..............................................................................................8
220V Operation........................................................................................9
Extension Cords........................................................................................9
Grounding ..............................................................................................9
ASSEMBLY INSTRUCTIONS ..............................................................................10
Unpacking ............................................................................................10
Box Contents..........................................................................................10
Shop Preparation ....................................................................................11
Cleaning Machine ....................................................................................11
Beginning ..............................................................................................12
Mounting Jointer ....................................................................................12
Installing V-belt ......................................................................................12
Dust Port ..............................................................................................13
Installing Fence ..................................................................................13-14
Cutterhead Guard....................................................................................14
Belt Cover ............................................................................................15
Knife Gauge ..........................................................................................15
Control Panel ........................................................................................15
Checking Knives......................................................................................16
Adjusting Knives ....................................................................................17
Table Gibs ............................................................................................18
Adjusting Tables ................................................................................18-19
Fence Stops ..........................................................................................20
OPERATIONS ..............................................................................................21
Starting Jointer ......................................................................................21
Basic Operations ....................................................................................21
Operation Musts......................................................................................22
Surface Planing ......................................................................................23
Edge Jointing ........................................................................................24
Bevel Cutting ........................................................................................25
Rabbet Cutting ......................................................................................26
MAINTENANCE ............................................................................................27
General ................................................................................................27
Table Surface ........................................................................................27
Lubrication............................................................................................28
Sharpening Knives ..................................................................................28
Troubleshooting..................................................................................29-30
Wiring Diagram ......................................................................................31
CLOSURE....................................................................................................32
Parts Breakdowns and Parts Lists ............................................................23-38
Warranty Information ..........................................................................39-40
3.
4.
5.
6.
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
About Your New Jointer
Your new Shop Fox® Jointer has been specially designed to provide many years of trouble-free service.
Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reli-
able operation.
The Model W1679 is capable of a wide variety of surface jointing/planing, edge jointing, beveling and
rabetting operations. The handwheels allow you to make precision table adjustments, the control panel
is easily accessible and the solid cabinet provides a vibration dampening base for smooth-quality cuts.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to make sure all the information necessary for safety, ease of assembly, practical use and dura-
bility of this product be included.
If you should have any comments regarding this manual, please feel free to contact us at:
Woodstock International, Inc.
Attn: Technical Department
P.O. Box 2309
Bellingham, WA 98227
Woodstock Service And Support
We stand behind our machines! In the event that a defect is found, parts are missing or questions arise
about your machine, please contact Woodstock International Service and Support at 1-360-734-3482 or
send e-mail to: [email protected]. Our knowledgeable staff will help you troubleshoot
problems, send out parts or arrange warranty returns.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty And Returns
Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from workman-
ship and materials for a period of 2 years from the date of original purchase by the original owner. This
warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents,
lack of maintenance, or to repairs or alterations made or specifically authorized by anyone other than
Woodstock International, Inc.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX®
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair facility
designated by our Bellingham, WA office, with proof of their purchase of the product within 2 years, and
provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through
inspection. If it is determined there is no defect, or that the defect resulted from causes not within the
scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing
and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies with
the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this war-
ranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock
International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event
be liable for death, injuries to persons or property or for incidental, contingent, special or consequen-
tial damages arising from the use of our products.
Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durability
standards. We reserve the right to change specifications at any time because of our commitment to con-
tinuously improve the quality of our products.
Machine Specifications
Motor Size:........................................................1 HP, 110/220V, Single-Phase
Motor Speed: ..............................................................................3450 RPM
Amps: ............................................................................................14/7
Maximum Width of Cut: ..........................................................................6"
Maximum Depth of Cut: ........................................................................1⁄8
"
"
Maximum Rabbet: ................................................................................1⁄2
Cutterhead: ..................................................................3 Knife, 3" Diameter
Cutterhead Speed: ......................................................................5500 RPM
Cuts Per Minute: ............................................................................16,500
Fence Tilt:........................................................................45˚L, 90˚, 45˚ R
Machine Weight: ............................................................................235 lbs
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ MANUAL BEFORE OPERATING MACHINE.
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury, or MAY result in property damage.
This symbol is used to alert the user to useful information about proper
operation of the equipment.
NOTICE
Standard Safety Instructions
1. Thoroughly read the instruction manual before operating your machine. Learn the applications,
limitations and potential hazards of your machine. Keep this manual in a safe, convenient place for
future reference.
2. Keep the work area clean and well lighted. Clutter and inadequate lighting invite potential haz-
ards.
3. Ground all tools. If a machine is equipped with a three-prong plug, plug it into a three-hole ground-
ed electrical outlet or grounded extension cord. If using an adapter to aid in accommodating a two-
hole receptacle, ground using a screw to a known ground.
4. Wear eye protection at all times. Use safety glasses with side shields or safety goggles that meet
the national safety standards, while operating this machine.
5. Avoid dangerous environments. Do not operate this machine in wet or open flame environments.
Airborne dust particles could cause an explosion and severe fire hazard.
6. Ensure all guards are securely in place and in working condition.
7. Make sure the power switch is in the “OFF” position before connecting power to machine.
8. Keep the work area clean, free of clutter, sawdust, dirt or grease.
9. Keep visitors at a safe distance away while operating this machine.
10.Childproof the workshop with padlocks, master switches or by removing starter keys.
11.Disconnect the machine when cleaning, adjusting or servicing.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
12.Do not force the machine. The machine will do a safer and better job at the rate for which it was
designed.
13.Use the correct tool. Do not force the tool or attachment to do a job for which it was not designed.
14.Wear the proper apparel. Do not wear loose clothing, neck ties, gloves, jewelry, keep long hair tied
up, etc.
15.Remove all adjusting keys and wrenches. Before turning the machine on, make it a habit to check
that all adjusting keys and wrenches have been removed.
16.Use proper extension cord. Examine the extension cord to ensure it is in good condition. Use the
chart below to determine the correct length and gauge of extension cord needed for your particular
needs. The amp rating of the motor can be found on its nameplate. If the motor is dual voltage, be
sure to use the amp rating for the voltage you will be using. If you use an extension cord with an
undersized gauge or one that is too long, excessive heat will be generated within the circuit increas-
ing the chance of a fire or damage to the circuit. Only use an extension cord that has a ground pin.
Immediately replace an extension cord if it shows any signs of damage.
17.Keep your footing stable and keep your balance at all times.
18.Do not leave machine the unattended. Wait until it comes to a complete stop before leaving the
area.
19.Perform all machine maintenance, and follow all lubrication instructions in this manual.
20.Keep the machine away from open flame. Operating machines near pilot lights and/or open flames
creates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause
an explosion. Do not operate the machine in high-risk areas, including but not limited to, those men-
tioned above.
21. If at any time you are experiencing difficulties performing the intended operation, stop using the
machine! Then contact our service department or ask a qualified expert how the operation should
be performed.
22. Habits—good and bad—are hard to break. Develop good habits in your shop and safety will become
second-nature to you.
Extension Cord Requirements
Always wear safety glasses or goggles when
Length And Gauge
25ft 50ft 100ft
operating equipment. Operating this equip-
ment creates the potential for flying debris
to cause eye injury. Everyday glasses or
reading glasses only have impact resistant
lenses, they are not safety glasses. Be cer-
tain the safety glasses you wear meet the
appropriate standards of the American
National Standards Institute (ANSI).
Amp Rating
0-6
#18
#18
#16
#14
#12
#10
#16
#16
#16
#12
#12
#10
#16
#14
#14
#12
#10
No
7-10
11-12
13-16
17-20
21-30
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions For Jointers
1. JOINTING SAFETY BEGINS WITH YOUR LUMBER. Inspect your stock carefully before you feed it over
the cutterhead. If you have any doubts about the stability or structural integrity of your stock, DO
NOT JOINT IT!
2. MAINTAIN THE PROPER ALIGNMENT of the outfeed table with the cutterhead knife.
3. ALWAYS USE PUSH BLOCKS WHEN JOINTING. Never allow your hands to get near the cutterhead.
4. SUPPORT AND MAINTAIN CONTROL OVER THE WORKPIECE at all times during operation.
5. WHEN JOINTING, DO NOT STAND DIRECTLY BEHIND THE WORKPIECE. Position yourself just to the
side of the infeed table to avoid possible kickbacks.
6. NEVER MAKE CUTS deeper than 1⁄8".
7. NEVER JOINT A BOARD THAT HAS LOOSE KNOTS. All defects should be removed before use.
8. JOINT WITH THE GRAIN. Jointing against the grain is dangerous and could produce chatter or exces-
sive chip out. NEVER JOINT END GRAIN.
9. WITH THE EXCEPTION OF RABBETING, all operations must be performed with the guard in place.
After rabbeting, be sure to replace the guard.
10. NEVER BACK THE WORK toward the infeed table.
11. HABITS—GOOD AND BAD—ARE HARD TO BREAK. Develop good habits in your shop and safety will
become second-nature to you.
12. “KICKBACK” is when the workpiece is thrown off the jointer table by the force of the cutterhead.
Always use push blocks and safety glasses to reduce the likelihood of injury from “kickback.” If you
do not understand what kickback is, or how it occurs, DO NOT operate this machine.
13. BE AWARE THAT CERTAIN WOODS MAY CAUSE AN ALLERGIC REACTION in people and animals,
especially when exposed to fine dust. Make sure you know what type of wood dust you will be
exposed to and always wear an approved respirator.
Read and understand this
Use this and other machinery with caution
entire instruction manual
and respect. Always consider safety first, as
before performing any
it applies to your individual working condi-
operations with your
tions. No list of safety guidelines can be com-
machine. Serious personal
plete—every shop environment is different.
injury may occur if safety
Failure to follow guidelines could result in
and operational informa-
serious personal injury, damage to equip-
tion is not understood and
ment or poor work results.
is not followed. Do not risk
your safety by not read-
ing!
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Avoiding Potential Injuries
Figure 1. Correct operator and workpiece position,
guard is in place, and push blocks are being used.
Figure 2. Never surface plane without push blocks!
Figure 3. Never stand directly behind the workpiece!
Figure 4. Never plane/edge-joint with
Figure 5. Never joint end grain!
the guard removed!
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
110V Operation
Do not remove the ground-
ing pin from any plug and
always make sure all wiring
to the machine is grounded
before operating. Any elec-
trical outlet and circuit that
you plug your machine into
must be grounded. Serious
injury may occur if this
warning is ignored!
The Shop Fox® W1679 is prewired for 110 volts.
The motor supplied with your new machine is
rated at 1 HP and will draw approximately 14
amps. When choosing an outlet for this machine,
consider using one with a 15 amp circuit break-
er or fuse. When choosing plug and outlet, use a
NEMA-style 5-15 as shown in Figure 6. Keep in
mind that a circuit being used by other machines
or tools at the same time will add to the elec-
trical load being applied by the machine. Add up
the load ratings of all machines on the circuit. If
this number exceeds the rating of the circuit
breaker or fuse, use a different circuit.
Extension Cords
When it is necessary to use an extension cord,
use the following guidelines:
•Use cords rated for Hard Service
•Never exceed a length of 100 feet
•Use cords with 14 ga. wire or bigger
(12 ga., 10 ga., etc.)
•Make sure cord has a ground wire and pin
•Do not use damaged cords
Figure 6. NEMA-style 5-15 plug and outlet.
Grounding
This machine must be grounded! The electrical
cord supplied with the Model W1679 comes with
a grounding pin. Do not remove it. See Figure 7.
If your outlet does not accommodate a ground
pin, have it replaced by a qualified electrician
or have an appropriate adapter installed. Please
note: when using an adapter, the adapter must
be grounded.
An adapter with a grounding wire does not guar-
antee the machine will be grounded. A ground
source must be verified.
Figure 7. Never remove grounding pin.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
220V Operation
Do not remove the ground-
ing pin from any plug and
always make sure all wiring
to the machine is grounded
before operating. Any elec-
trical outlet and circuit that
you plug your machine into
must be grounded. Serious
injury may occur if this
warning is ignored!
The Shop Fox® W1679 can also be operated at
220 volts. To do this, you must purchase the
optional 220V magnetic switch that is shown in
the parts diagram at the back of this manual.
Also, you will need a NEMA-style 6-15 plug and
outlet.
The motor supplied with your new machine is
rated at 1 HP and will draw approximately 7
amps during 220 volt operation. When choosing
an outlet for this machine, consider using one
with a 10 amp circuit breaker or fuse. When
choosing plug and outlet, use a NEMA-style 6-15
as shown in Figure 8. Keep in mind that a circuit
being used by other machines or tools at the
same time will add to the total load being
applied to the circuit. Add up the load ratings of
all machines on the circuit. If this number
exceeds the rating of the circuit breaker or fuse,
use a different circuit.
Extension Cords
We do not recommend using an extension cord
for 220V equipment. Instead, arrange the place-
ment of your machinery and installed wiring to
eliminate the need for extension cords. If you
must use an extension cord, make sure it is
rated Hard Service (grade S) or better. The
extension cord must always contain a ground
wire and plug pin. Always repair or replace
extension cords when they become worn or
damaged.
Figure 8. NEMA-style 6-15 plug and outlet.
Never replace the circuit breaker with one
rated at a higher amperage or damage to
the circuit may occur, and a fire may
result!
Grounding
This machine must be grounded! See Figure 8.
The electrical cord supplied with the Model
W1679 is not equipped with a 220 volt plug. Use
a plug with a ground pin. If your outlet does not
accommodate a ground pin, have the outlet
replaced by a qualified electrician or have an
appropriate adapter installed and grounded
properly. An adapter with a grounding wire does
not guarantee the machine will be grounded. A
ground source must be verified.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
Unpacking
Read and understand this
entire instruction manual
before performing any
operations with your
machine. Otherwise, seri-
ous personal injury may
occur if safety and opera-
tional information is not
understood and followed.
Do not risk your safety by
not reading!
The Model W1679 has been carefully packaged
for safe transporting. If you notice the machine
has been damaged or is missing any parts,
please contact Woodstock International Service
and Support at 1-360-734-3482 or send e-mail
to: [email protected].
Box Contents
The following is a description of the components
shipped with the Shop Fox® W1679. It is recom-
mended that the components be laid out in a
similar fashion to those in Figure 9. This will
help in identification before beginning assem-
bly. Should any part be missing, examine the
packaging carefully. If any key parts are missing,
find the part number in the back of this manual
and call Woodstock International, Inc. at 360-
734-3482 or e-mail at: tech-support@woodstock-
int.com.
Seek lifting assistance
before beginning assem-
bly. The Model W1679 is
a heavy load at 235
pounds.
1
Item
Qty.
7
11
1. Cabinet Stand
1
2. Table Assembly
3. Fence Assembly
4. Push Blocks
1
1
2
1
1
1
1
1
1
1
1
1
3
5. Cutterhead Guard
6. Fence Support Key
7. Dust Port
5
2
8. Fence Tilt Knob 3⁄8"-16 x 23⁄4
"
12
9. Lock Knob 1⁄2"-12 X 33⁄4
"
Special Nut 1⁄2"-12
4
Flat Washer 1⁄2
"
10
6
8
9
10. V-Belt A-36
11. Belt Cover
12. Hardware Bags:
Figure 9. Jointer components removed from
the boxes and laid out for identification.
Hex Bolts 3⁄8"-16 x 3⁄4
"
3
3
4
8
Lock Washers 3⁄8
"
Hex Nuts 5⁄16"-18
Hex Washers 5⁄16"
Phillps Head Screws 5⁄16"-18 x 1⁄2" 4
Knife Setting Gauge Kit
1
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
Shop Preparation
Cleaning Machine
•
•
•
Floor Load: Your Model W1679 represents a
large weight load in a small footprint. While
most commercial floors are suitable for this
jointer, some residential floors may require
additional bracing to support both machine
and operator.
The table and other unpainted parts of the
Model W1679 are coated with a waxy grease that
protects them from corrosion during shipment.
For optimum performance from your machine,
make sure you clean all moving parts or sliding
contact surfaces that are coated. Clean this
grease off with a solvent cleaner or citrus-based
degreaser. Do not use chlorine-based solvents—
if you happen to splash some onto a painted sur-
face, you will ruin the finish.
Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through each machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your machine.
Never use flammables
such as gas or other petro-
leum-based solvents to
Lighting and Outlets: Lighting should be
bright enough to eliminate shadow and pre-
vent eye strain. Electrical circuits should be
dedicated or large enough to handle amper-
age requirements. Outlets should be locat-
ed near each machine so power or exten-
sion cords are clear of high-traffic areas.
Observe local electrical codes for proper
installation of new lighting, outlets, or cir-
cuits.
clean
your
machine.
These products have low
flash points and present
the risk of explosion and
severe personal injury!
Never smoke while using
any cleaning solvents.
Smoking may cause explo-
sion or risk of fire when
exposed to these products!
Always make sure that all
entrances to your shop are
locked or that machines
are equipped with safety
lock-out devices to protect
curious children or visitors
from serious injury. Never
allow unsupervised people
in your shop who have not
been fully trained!
Most solvents used to
clean machinery are
toxic when inhaled or
ingested. Always work in
a well ventilated area
when using these prod-
ucts and keep away from
any potential ignition
sources (pilot lights).
Always dispose of any
waste rags in a sealed
container to make sure
they do not cause fire or
environmental hazards.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Beginning
Although the main components of the Shop Fox®
W1679 are assembled at the factory, some
assembly is required. The following series of
instructions are the recommended sequence
best suited for final assembly.
Make sure that your
machine is unplugged
during all assembly pro-
cedures! If this warning
is ignored, serious per-
sonal injury may occur.
Mounting Jointer
1. Determine the best place for the jointer in
your shop and place the cabinet stand in
that location.
2. With the help of a friend, lift the jointer
assembly onto the stand so the cutterhead
pulley is positioned directly over the slot in
the top of the stand.
3. Align the mounting holes (shown in Figure
10) on the stand to the jointer assembly,
and secure the jointer assembly with the (3)
3
3
⁄
8" - 16 x ⁄4" hex bolts and lock washers
from the hardware bag.
Figure 10. Secure table to stand at these locations.
Installing V-Belt
1. Figure 11 shows the jointer motor mount
bolts inside of the dust chute. Loosen the
nuts so you can slide the motor up and
install the V-belt.
2. With the V-belt in the grooves of both the
motor pulley and the cutterhead pulley,
pull the motor down tightly by hand and
tighten one corner bolt.
3. Place your straightedge against the face of
both pulleys, and swivel the motor as nec-
essary until both pulleys line up with each
other. Tighten the other three motor mount
bolts.
Figure 11.
Motor mount bolts inside
dust chute (two are not shown).
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Halfway between the two pulleys, lightly
squeeze each side of the belt together to
check the tension.
Belt too loose? If each side of the belt
squeezes toward each other more than 1⁄2",
increase the tension by repeating steps 2
and 3.
DO NOT over-tighten the belt! Do not use
pry bars or any other device to force the
motor down as this may over-tighten the
belt, which may damage the balance of the
motor shaft or bearings and increase the
wear of the power transfer components.
Figure 12. Pulley and V-belt alignment.
5. Check the V-belt pulley alignment. Minor
adjustments may be made by loosening the
pulley setscrew and sliding the pulley along
the shaft. See Figure 12 for details.
Dust Port
Using the (4) phillips head screws from the hard-
ware bag, attach the dust port over the dust
chute at the mounting holes shown in Figure 13.
Installing Fence
1. The fence support key has a roll pin fitted in
the center. Install the key into the fence
support keyway and fit the roll pin into the
provided hole. Figure 14 shows the key
installed correctly.
Figure 13. Dust port mounting holes.
Fence
Support
2. Get a friend to help you lift and place the
fence on this support.
Key
NOTICE
Do not slide the fence across the outfeed
table. Scratching will result.
3. Locate the threaded hole on the back of the
infeed side of the fence and install the
fence tilt knob into the fence.
Figure 14. Installing key into fence support.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Place the 1⁄2" flat washer over the lock knob
and install the special nut from underneath
the fence support as shown in Figure 15.
Lock
Knob
5. Make sure the splines on the special nut pro-
trude into the adjustment slot, then insert
the knob through the fence housing and
thread the knob into the special nut.
Tilt
Knob
Special
Nut
Cutterhead Guard
1. Remove the setscrew from the slot in the
end of the cutterhead guard shaft.
Figure 15. Installing lock knob and special nut.
2. Rotate the spring housing clockwise (looking
at the face of the knob) 1 full turn and
insert the cutterhead shaft into the pivot
hole as shown in Figure 16.
Pivot
Hole
Cutterhead
Guard
Shaft
Spring
Housing
3. Fit the shaft slot over the tang inside the
spring housing. The shaft should drop
through the bottom of the housing.
4. When
installed, the cutterhead guard
should press firmly against the fence and
should be completely covering the cutter-
head as shown in Figure 17.
5. Move the cutterhead guard back and forth
to make sure that it automatically returns
back to its proper position against the fence
and over the cutterhead.
Figure 16. Rotate spring housing clockwise 1 full
turn and insert cutterhead guard shaft.
6. Make sure the cutterhead guard has the
correct return pressure. If the pressure is
weak or there is no return pressure at all,
remove the shaft, tighten the spring housing
by rotating clockwise, and re-install the
shaft to check for proper operation.
7. Replace the setscrew at the end of the
shaft, so that the cutterhead guard cannot
be removed from the pivot hole.
Figure 17. Guard in proper position against
the fence and completely over the cutterhead.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Guard
Attach the belt cover to the cabinet stand with
5
the ⁄16"-18 x 21⁄2" hex bolt as shown in Figure
18.
Make sure that your
machine is unplugged
during all assembly pro-
cedures! If this warning
is ignored, serious per-
sonal injury may occur.
Figure 18. Attach belt guard to stand
with the hex bolt.
Knife Gauge
The knife gauge consists of a steel rod, two
adjuster arms and two E-clips.
To assemble the knife gauge:
1. Insert the steel rod through each adjuster
arm.
2. Snap the E-clips into the grooves at the ends
of the steel rod so your assembly looks like
the knife gauge shown in Figure 19.
Figure 19. Knife setting gauge.
See page 16-17 for usage instructions.
Control Pedestal
1. Mount the control pedestal to the back of
the cabinet stand as shown in Figure 20.
2. Secure the control pedestal with the (4)
5⁄16" hex nuts and (4) 5⁄16" washers from the
hardware bag.
Figure 20. Mounting pedestal switch to stand.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
Checking Knives
The cutterhead knives have been set at the fac-
tory and should require no adjustments when
you first receive your jointer. However, it is
always a good idea to verify the accuracy of any
adjustments that will affect your finished prod-
uct.
Make sure that your
machine is unplugged
during any adjustment
procedures!
If
this
warning is ignored, seri-
ous personal injury may
occur.
As your jointer gets used, the knives will need to
be routinely inspected, adjusted, and ultimate-
ly replaced.
To inspect knife position in the cutterhead:
1. Unplug the jointer!
The cutting edges on this
equipment are extreme-
ly sharp! Be very careful
when working around
these edges. Never di-
rectly grab the cutter-
head to move it!
2. Remove the cutterhead guard from the
table, so that you have unfettered access to
the top of the cutterhead.
3. Remove the pulley cover at the back of the
machine and slowly turn the cutterhead
with the pulley until one of the knives is
exposed and is easily accessible.
These Points Must
All Touch Evenly
4. Using the knife setting gauge as shown in
Figure 21, check the height of the knife.
Both gauge feet should sit solidly on the
cutterhead and the contact point in the
center of the gauge arm should barely touch
the tip of the knife.
If the gauge fits on the cutterhead as
described above, then the knife height is cor-
rect. Move on to the next knife and check in the
same manner. If all of the other knives are at
the correct height, then no adjustments are
necessary.
Figure 21. Place the knife setting gauge on the
cutterhead as shown to inspect accuracy of
knife position in cutterhead.
If either gauge arm does not fit on the cutter-
head as described above, or if the center con-
tact point does not touch the knife, then the
knife position needs to be adjusted. Refer to
the “Adjusting Knives” instructions in this sec-
tion and adjust the knives.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Knives
The knives in the Model W1679 come from the
factory with jack screws installed. Springs are
also included as an option for knife adjustments,
depending on your preference. Figure 22 shows
an illustration of the cutterhead components.
The knife position should be as precise as possi-
ble in the cutterhead. All knives should be with-
in .002" from one end to the other and within
.002" from one knife to another.
To adjust the knives:
1. Unplug the jointer!
Understanding cutterhead assembly.
Figure 22.
2. Remove the cutterhead guard from the
table, so that you have clear access to the
top of the cutterhead.
3. Remove the pulley cover at the back of the
machine and slowly turn the cutterhead
with the pulley until one of the knives is
exposed and is easily accessible.
Wear heavy leather gloves when loosen-
ing/tightening gib bolts in case the wrench
slips and your hand hits the knife. Planer
knives are dangerously sharp. If care is not
taken, serious injury may occur.
4. Loosen the cutterhead gib bolts so that the
knife is loose.
5. Place the knife gauge on the cutterhead as
described in the “Checking Knives” instruc-
tions and as shown in Figure 22.
NOTICE
Uneven tightening of the gib bolts may cause
the cutterhead to become unbalanced,
which will lead to premature wear and tear
of the knives and produce poor results!
6. Jack Screws—Adjust the jack screws with
an Allen wrench until the knife edge barely
touches the contact point on the knife set-
ting jig. Snug the gib bolts but do not fully
tighten. Repeat this step with each jig
screw on each knife.
Springs—The springs will push the knife
against the cutterhead to the proper height
(.070" above cutterhead body). Keep down-
ward pressure on the jig until you tighten
the gib bolts. Repeat this step with the
other knives, then snug the gib bolts with-
out fully tightening them.
1
3
4
2
7. Start at the beginning knife and slightly
tighten each gib bolt on each knife in the
sequence shown in Figure 23. Repeat this
step two or three times until all gib bolts
are completely tight.
Gib bolt tightening sequence.
Figure 23.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Gibs
The table gibs allow you to control how easy the
table moves up or down and control the preci-
sion of the table movement along the dovetail
ways. Since the table gibs are factory set, they
do not need to be adjusted unless the table is
too loose or too tight when moving along the
dovetail ways. (Always make sure the table lock
is released before determining whether the
table travel is too loose or too tight.)
To adjust the table gibs:
1. Unplug the jointer!
Figure 24. These are the table gib controls.
2. Locate the setscrews and jam nuts shown in
Figure 24. These are used to tighten/loosen
the table gibs.
3. Use the trial-and-error method by adjusting
the setscrews and moving the table to
achieve the correct table movement. When
both tables move smooth and responsive,
with no indication of side-to-side move-
ment, then the table gibs are set right.
Adjusting Tables
The tables are adjusted by rotating the hand-
wheels. In order to accurately joint or plane a
piece of stock, both tables must be properly
adjusted, starting with the outfeed table.
Figure 25. This is the outfeed table lock handle.
To adjust the outfeed table:
1. Unplug the jointer!
2. Make sure that the knives have been prop-
erly adjusted before continuing.
3. Turn the lock handle counterclockwise to
loosen the lock, so that the outfeed table
can move freely. Figure 25 shows the out-
feed table lock handle.
4. Remove the motor pulley cover to expose
the V-belts and pulleys. Rotate the cutter-
head by turning the cutterhead pulley until
one of the blades is at the highest point in
its arc (top dead center) as illustrated in
Figure 26.
Figure 26. Top dead center.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place a good quality straightedge across the
length of the outfeed table and just over
the cutterhead as shown in Figure 27. (This
adjustment works best if the straightedge is
placed in the center of the outfeed table.)
6. Using the handwheel under the outfeed
table, raise or lower the outfeed table until
the straightedge barely touches the edge of
the knife.
7. Move the cutterhead back and forth to ver-
ify that it is still positioned at top dead cen-
ter.
Figure 27. Straightedge centered on outfeed
table and even with knife at top dead center.
8. Tighten the table lock handle and double
check your adjustment for accuracy.
After adjusting the outfeed table and ensuring
its accuracy, it can be left alone until the next
time you adjust the knives or if you notice that
it might have moved. The infeed table, on the
other hand, will regularly be adjusted to set the
cutting depth.
To adjust the infeed table:
1. Loosen the infeed table lock handle.
2. Place a good quality straightedge in the
center and along the length of the outfeed
table.
Figure 28. Infeed table even with outfeed.
Scale can now be set to “0”.
3. Slide the straightedge over the infeed table.
4. Raise the infeed table so it barely touches
the bottom of the straightedge as shown in
Figure 28.
5. Secure the infeed table with the lock handle
and set the pointer on the depth scale to
“0” as shown in Figure 29. You can now use
the scale to adjust your depth of cut when
it is time to operate the jointer.
Figure 29. Pointer set to “0”.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Fence Stops
45˚L
Stop bolts on the back of the fence (shown in
Figure 30) allow you to quickly and accurately
move the fence to 90˚, 45˚ R (to the right) and
45˚ L (to the left). The position of these stops
must be checked and possibly adjusted before
they are used for the first time.
90˚
Fence-Tilt
Lock Knob
45˚R
The fence stops are simple hex bolts (a nut for
45˚ L) that thread in or out to match the depth
required. Each fence stop has a jam nut to lock
the stops in place for repeatable accuracy.
To check/adjust the fence stops:
1. Unplug the jointer!
Figure 30. Fence stops and fence-tilt lock knob.
2. 90˚ Stop — Loosen the fence-tilt lock knob.
Move the fence into an upright position so
the 90˚ stop is resting against the metal
tab. Place a try square on the table and
against the fence as shown in Figure 31. If
the square does not line up with the table
and fence evenly, adjust the 90˚ stop bolt
until it does. Tighten the jam nut down to
prevent it from moving and retighten the
fence-tilt lock knob.
3. 45˚ R Stop — Make sure the fence-tilt lock
knob is loose, then slide the 90˚ stop tab
out of the way and tilt the fence back into
position shown in Figure 32. The fence
should rest on the stop. Check the angle
with a 45˚ angle gauge to verify for accura-
cy. Adjust the stop if needed and tighten
the jam nut. Retighten the fence-tilt lock
knob before operation.
Figure 31. Squaring fence with a try square.
4. 45˚ L Stop — Loosen the fence-tilt lock
knob. Move the fence 45˚ to the left so it
tilts toward the table and stops on the 45˚L
stop nut. Adjust the stop nut if necessary
and tighten the jam nut (the second nut
behind the first) to the stop nut to keep it
from moving. Retighten the fence-tilt lock
knob before operation.
Always double check the stop bolt position
after tightening the jam nuts!
Figure 32. This is the fence in the 45˚ R position.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
Starting Jointer
Always wear safety glass-
es during operations.
Serious injury may occur
if this is warning is ig-
nored!
Once assembly is complete and adjustments
have been made, the jointer is ready for a test
run. The purpose of a test run is to identify any
unusual noises and vibrations, as well as to con-
firm the machine is performing as intended.
1. With your finger poised to hit the STOP but-
ton if there is a problem, turn on the joint-
er by pressing the START button on the
power switch.
Always
keep
loose
clothing and long hair
secured and away from
moving parts.
2. Once the jointer is running, listen for any
unusual noises. It should run smoothly with
little or no vibrations. If there are any
unusual noises or vibrations, shut the joint-
er off immediately. It should not be run any
further until the problems are corrected.
DO NOT operate this
machine without an ade-
quate dust collection
system. This machine
creates
amounts of wood dust
while in operation.
3. Unplug the jointer and investigate the
source of the noise or vibration. Do not
make any adjustments to the machine while
it is plugged in.
substantial
4. Repeat Steps 1-4 until the jointer runs
smoothly.
Failure to use a dust col-
lection system can result
in short and long-term
respiratory illness.
Basic Operations
All operations on the jointer are made by plac-
ing the workpiece firmly against the infeed table
and the fence, and then passing the workpiece
completely over the cutterhead.
Always wear a dust mask
and safety glasses in addi-
tion to using a dust col-
lector. This machine pro-
duces sawdust that may
cause allergic reactions
or respiratory problems.
Operational tips as well as specific types of cuts
are mentioned further on in this section. If you
are a beginner, it is a good idea to practice each
new type of cut with the fence in the desired
position, the tables set even and the machine
turned off. Get a feel for board control and hand
position, and practice feeding the board across
the table while maintaining absolute control.
When you are ready for the actual cut, keep in
mind that shallow cutting depths allow you to
have more control.
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Musts
•
•
Never allow hands or push blocks to come
within 4" of the cutterhead while it is mov-
ing.
Carefully inspect any lumber that you plan
to run through the jointer. Some defects
such as moderate twisting, loose knots or
severe cracks may make the stock unusable.
•
Only use clean stock. See Figure 33.
Remove all dirt, nails, staples, imbedded
gravel, etc. from any lumber you plan on
using. A hidden nail in a workpiece will
instantly damage the sharp edges of the
knives. This will cause unsatisfactory results
in future operations.
Figure 33. Only plane clean stock.
•
•
Use ONLY natural wood fiber. Never use
wood composites such as particle board,
plywood or MDF. Also, never use laminates,
formica or other synthetic materials.
Always cut WITH the grain. Cutting against
the pattern of the growth rings will chip the
wood instead of cutting it. This will make
the workpiece look rough and irregular and
may increase the chances of a kickback.
To determine if you are going to be cutting
with the grain, look at the pattern on the
side of the board. If the arc of the cutter-
head knife will follow the same lines in the
pattern, then you will be cutting WITH the
grain. If the arc of the cutterhead knife will
cross the lines in the stock pattern, then
you will be cutting AGAINST the grain. Refer
to Figure 34 for clarification.
Figure 34.
Correct and incorrect grain
alignment to cutterhead.
•
•
Sharpen knives immediately if they show
any signs of dulling during operation. We
recommend keeping a spare set of knives at
all times.
•
•
Avoid using wood with a high moisture con-
tent. Stock with more than 20% moisture, or
stock that has been exposed to rain or snow,
will cut poorly and cause unnecessary wear
on the knives and motor. Excess moisture
may also cause rust or corrosion problems.
Keep your work area clear. Always make
sure that long workpieces are supported and
have enough room to exit the jointer.
Never take cuts deeper than 1⁄8" and plan on
taking multiple cuts before you can achieve
a completely flat surface.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
Surface Planing
One of the most common operations on the join-
ter is surface planing. Surface planing produces
one flat surface on a piece of stock as shown in
Figure 35.
After being surface planed, the stock is usually
run through a thickness planer so the board
thickness is consistent from one end to the
other.
Figure 36 shows an example of an operator
using the jointer to surface plane a piece of
wood stock. Notice that the operator’s body is
not directly behind the stock and that the oper-
ator is using push blocks to feed the board.
Portion
Removed With
Jointer
Figure 35. Surface planing produces a flat sur-
face from concave stock.
To perform a surface planing operation:
1. Make sure you have read and are familiar
with Section 1: Safety and the “Operation
Musts” in this section.
Always wear safety
glasses to prevent seri-
ous personal injury!
2. Place the workpiece so the concave side is
down on the infeed table and press the
workpiece firmly against the fence.
3. Start the jointer.
4. Using push blocks with both hands and keep-
ing firm (not hard) pressure on the fence
and table, feed the workpiece into the cut-
terhead.
5. As your leading hand gets within 4" of the
cutterhead, lift the push block up and over
the cutterhead and place it on the work-
piece as it passes over the outfeed table. Do
the same thing when your trailing hand
nears the cutterhead and try to maintain
pressure on the outfeed table. Never let
your hands get closer than 4" from the cut-
terhead!
Figure 36. This is an example of a surface
planing operation.
6. Repeat steps 4-5 until the surface is flat.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
Edge Jointing
Edge jointing is passing the workpiece over the
jointer on its edge as shown in Figure 37. This
process makes the edges of a workpiece per-
fectly flat.
Stock must be edge jointed on the concave side.
The convex side should then be cut straight with
a table saw. This process is commonly used to
prepare the workpiece to be glued-up as part of
a larger assembly or to simply salvage warped
stock.
Portion
Removed With
Jointer
Figure 38 shows an example of an operator edge
jointing. Notice that the operator’s body is not
directly in line with the stock and that he main-
tains a stable hand position while keeping the
board firmly on the table and against the fence.
Figure 37. Edge jointing produces one flat edge.
To perform an edge jointing operation:
Always wear safety
glasses to prevent seri-
ous personal injury!
1. Follow Section 1: Safety and the “Operation
Musts” in this section.
2. Place the workpiece so the concave edge is
down on the infeed table and press the
workpiece firmly against the fence.
3. Start the jointer.
4. Using a tight grip with your hands in a sta-
ble position and keeping the workpiece
firmly against the table and fence, feed the
workpiece into the cutterhead.
5. If your leading hand gets within 4" of the
cutterhead, lift it up and over the cutter-
head and place it on the workpiece as it
passes over the outfeed table. Do the same
thing when your trailing hand nears the cut-
terhead and try to maintain pressure on the
outfeed table. Never let your hands get
closer than 4" from the cutterhead!
Figure 38. This is an example of an edge
jointing operation.
6. Repeat steps 4-5 until the surface is flat.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
Bevel Cutting
Bevel cutting is very similar to edge jointing, but
done with the fence tilted to a specific angle in
order to produce an angled edge as shown in
Figure 39. Usually bevel cuts are made on two
boards that will be joined together at a corner.
For bevel cuts, the model W1679 has preset
stops at 45˚ L and 45˚ R. If a different angle is
desired, use a bevel gauge to set the fence,
then lock it in position.
Portion
Removed With
Jointer
Figure 40 shows an example of an operator
bevel cutting at 45˚ R. Notice that the opera-
tor’s body is not directly in line with the stock
and that he maintains a stable hand position
while keeping the board firmly on the table and
against the fence.
Figure 39. Bevel cutting produces an
angled edge.
To perform a bevel cutting operation:
Always wear safety
glasses to prevent seri-
ous personal injury!
1. Follow Section 1: Safety and the “Operation
Musts” in this section.
2. Set the fence to the desired angle. Place
the workpiece down on the infeed table and
press it firmly against the fence.
3. Start the jointer.
4. Keep the workpiece firmly against the table
and fence, and feed the workpiece into the
cutterhead.
5. If your leading hand gets within 4" of the
cutterhead, lift the push block up and over
the cutterhead and place it on the work-
piece as it passes over the outfeed table. Do
the same thing when your trailing hand
nears the cutterhead and try to maintain
pressure on the outfeed table. Never let
your hands get closer than 4" from the cut-
terhead and always make sure that you have
control over the workpiece.
Figure 40. This is an example of a bevel cut-
ting operation with the fence set at 45˚.
6. Repeat steps 4-5 until the surface is flat.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Rabbet Cutting
Rabbet Cut
Rabbet cutting recesses a section of a workpiece
edge to create a strong but simple joint. Figure
41 illustrates a basic rabbet cut and two com-
mon joints.
Figure 42 shows an operator performing a rab-
bet cut. Notice that the fence is positioned close
to the edge of the table. The operator’s body is
not directly in line with the stock and he main-
tains a stable hand position while keeping the
board firmly on the table and against the fence.
Rabbet Joints
To perform a rabbet cutting operation:
Figure 41.
1. Follow Section 1: Safety and the “Operation
Musts” in this section.
2. Determine the width of your desired rabbet
and set the fence that distance away from
the edge of the knives.
Always wear safety
glasses to prevent seri-
ous personal injury!
3. Place the workpiece down on the infeed
table and press it firmly against the fence.
4. Start the jointer.
5. Keep the workpiece firmly against the table
and fence, and feed the workpiece into the
cutterhead.
6. As your leading hand gets within 4" of the
cutterhead, lift it up and over the cutter-
head and place it on the workpiece as it
passes over the outfeed table. Do the same
thing when your trailing hand nears the cut-
terhead. Never let your hands get closer
than 4" away from the cutterhead!
7. Repeat steps 4-5 until you have achieved
your desired rabbeting depth. The maxi-
Figure 42. This is an example of a rabbet
mum rabbet depth for the Model W1679 is
cutting operation.
1
⁄2".
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
General
Regular periodic maintenance on your Model
W1679 will ensure its optimum performance.
Make a habit of inspecting your machine each
time you use it. Check for the following condi-
tions and repair or replace when necessary.
Make sure that your ma-
chine is unplugged dur-
ing all maintenance pro-
cedures! If this warning
is ignored, serious per-
sonal injury may occur.
1. Loose mounting bolts.
2. Worn switch.
3. Worn or damaged cords and plugs.
4. Damaged drive belt.
Always wear safety
glasses to prevent seri-
ous personal injury!
5. Any other condition that could hamper the
safe operation of this machine.
Always
keep
loose
clothing and long hair
secured and away from
moving parts.
Table Surface
Tables can be kept rust-free with regular appli-
cations of products like SLIPIT® as shown in
Figure 43. For long term storage you may want
to consider products like Boeshield T-9™.
Whichever product you ultimately choose for a
table lubricant, make sure that it protects
against rust, allows the stock to slide easily and
will not stain expensive stock.
Figure 43. Applying lubricant to table surface.
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
Since all bearings are sealed and permanently
lubricated, simply leave them alone until they
need to be replaced. Do not lubricate them.
For the moving mechanisms on the fence assem-
bly, an occasional application of light machine
oil is all that is necessary. Before applying lubri-
cant, wipe the fence clean. Lubricate the pivot
points and move the fence back and forth as
shown in Figure 44. Your goal is to achieve ade-
quate lubrication. Too much lubrication will
attract dirt and sawdust.
Figure 44. Lubricating fence pivot points.
Finally keep the sliding surfaces clean and free
of any dirt or sawdust. Give these areas, espe-
cially the key and keyway, an application of
white lithium grease as shown in Figure 45.
Graphite is also a great alternative to grease for
these areas because it does not attract dirt or
sawdust.
Sharpening Knives
Unless you are well experienced with knife
sharpening, have your knives sharpened by a
professional or simply replace them.
Figure 45. Greasing fence keyway.
Replacing V-Belt
If the V-belt becomes worn, cracked or glazed,
replace it.
To replace the V-belt:
1. Unplug the jointer!
2. Remove the dust cover and loosen the four
motor mount bolts (two are shown in Figure
46) in the dust chute.
3. Remove the V-belt from the pulleys.
4. Follow the “Installing V-Belt” instructions
on page 12 to install the V-belt.
Figure 46. Motor mount bolts located
in dust chute.
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
POSSIBLE REASON
SYMPTOM
HOW TO REMEDY
Motor will not start and fuses or
breakers blow.
1. Short circuit in line cord or plug.
1. Inspect cord or plug for damaged insulation and shorted
wires.
2. Short circuit in motor or loose con- 2. Inspect all connections on motor for loose or shorted ter-
nections. minals or worn insulation.
3. Incorrect fuses or circuit breakers in 3. Replace with correct fuses or circuit breakers.
power line.
Motor will not start.
Motor overheats.
1. Voltage too low.
1. Call an electrician to correct power line voltage.
2. Open circuit in motor or loose con- 2. Inspect all lead connections on motor for loose or open
nections.
connections.
1. Motor overloaded.
1. Reduce load on motor.
2. Restricted air circulation through 2. Clean out motor to provide proper circulation.
motor.
Motor stalls, resulting in blown
fuses or tripped breaker.
1. Short circuit in motor or loose con- 1. Inspect connections on motor for loose or shorted termi-
nections.
nals or worn insulation.
2. Voltage too low.
2. Call an electrician to correct power line voltage.
3. Incorrect fuses or circuit breakers in 3. Replace with correct fuses or circuit breakers.
power line.
4. Motor overloaded.
4. Reduce load placed on motor.
Loud, repetitious noise coming
from jointer.
1. Pulley setscrews or keys are missing 1. Replace or tighten setscrews or keys if necessary.
or loose.
2. Motor fan is hitting the cover.
3. V-belt is defective.
2. Tighten fan or shim motor cover.
3. Replace V-belt. See page 28.
Jointer slows when operating.
1. Too fast of a feed rate.
2. Too deep of cut.
1. Feed workpiece at a slower rate.
2. Decrease depth of cut.
Jointer cuts loud, overheats or
bogs down in cut.
1. Too deep of cut.
2. Knives are dull.
1. Decrease depth of cut.
2. Replace or sharpen knives.
Gouge in the end of board that is 1. Outfeed table set too low.
uneven with rest of cut (snipe).
1. Set outfeed table even with cutterhead knife at top dead
center. See page 18-19.
Workpiece stops or bumps out-
feed table in middle of cut.
1. Outfeed table set too high.
1. Set outfeed table even with cutterhead knife at top dead
center. See page 18-19.
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
POSSIBLE REASON
SYMPTOM
HOW TO REMEDY
Chipping occurs on workpiece.
1. Grain direction incorrect or knots in 1. Feed workpiece with the grain. Inspect stock for knots or
workpiece.
try again with different stock.
2. Replace or sharpen knives.
3. Feed the workpiece at a slower rate.
4. Decrease depth of cut.
2. Dull knives.
3. Too fast of a feed rate.
4. Too deep of cut.
Grain is fuzzy after jointing.
1. Wood may have high moisture con- 1. Allow wood to dry.
tent. Check with moisture meter.
2. Dull knives.
2. Replace or sharpen knives.
3. Wood is figured or is a species that 3. Use different wood or plan on extra sanding.
has naturally fuzzy characteristics.
Lines or ridges in board.
1. Nicked or chipped knives.
1. Inspect and replace or sharpen knives.
Uneven knife marks on board.
1. One or more knives out of adjust- 1. Reset/adjust knives in cutterhead. See page 17.
ment.
Wavy surface or chatter marks on 1. Too fast of a feed rate.
1. Feed the workpiece at a slower rate.
board.
2. One or more knives out of adjust- 2. Reset/adjust knives in cutterhead. See page 17.
ment.
Edge is concave or convex after
edge jointing.
1. Workpiece not held with even pres- 1. Hold workpiece with even pressure as it moves through
sure on infeed and outfeed table.
2. Workpiece began too uneven.
the cutterhead. See “Edge Jointing” on page 24.
2. Take partial cuts to remove extreme high spots before
doing a full pass.
3. Workpiece has excessive bow or 3. Surface plane one face so there is a good surface to posi-
twist along its length.
tion against the fence.
4. Insufficient number of passes.
4. Three to five passes may be needed to achieve a perfect
edge, depending on starting condition and depth of cut.
5. Outfeed table not properly aligned 5. Set outfeed table even with cutterhead knife at top dead
with cutterhead.
center. See page 18-19.
Workpiece tapered after jointing. 1. Outfeed table set too low.
1. Set outfeed table even with cutterhead knife at top dead
center. See page 18-19.
Feed Direction
Infeedꢀ
Table
Outfeedꢀ
Table
Cutterhead Rotation
Outfeed table set too low.
Outfeed table set too high.
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOSURE
The following pages contain parts diagrams/lists
We recommend you keep this manual for com-
plete information regarding Woodstock
International, Inc.’s warranty and return policy.
Should a problem arise, we recommend that you
keep your proof of purchase with your manual.
If you need additional technical information
relating to this machine, or if you need general
assistance or replacement parts, please contact
the Service Department at 1-360-734-3482 or e-
mail: [email protected].
and a warranty card for your Shop Fox® Model
W1679.
If you need parts or help in assembling your
machine, or if you need operational informa-
tion, we encourage you to call our Service
Department. Our trained service technicians will
be glad to help you.
If you have comments dealing specifically with
this manual, please write to us using the address
in the General Information. The specifications,
drawings, and photographs illustrated in this
manual represent the Model W1679 as supplied
when the manual was prepared. However, due
to Woodstock International, Inc.’s policy of con-
tinuous improvement, changes may be made at
any time with no obligation on the part of
Woodstock International, Inc.
Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines, and your
local library are good places to start.
The Model W1679 is specifically designed for
wood cutting operations. DO NOT MODIFY
AND/OR USE THIS MACHINE FOR ANY OTHER
PURPOSE. MODIFICATIONS OR IMPROPER USE
OF THIS TOOL WILL VOID THE WARRANTY. If
you are confused about any aspect of this
machine, DO NOT use it until all your questions
have been answered.
We have included some important safety mea-
sures that are essential to this machine’s opera-
tion. While most safety measures are generally
universal, we remind you that each workshop is
different and safety rules should be considered
as they apply to your specific situation.
Always wear safety glasses or goggles when
operating equipment. Operating this equip-
ment creates the potential for flying debris
to cause eye injury. Everyday glasses or
reading glasses only have impact resistant
lenses, they are not safety glasses. Be cer-
tain the safety glasses you wear meet the
appropriate standards of the American
National Standards Institute (ANSI).
Use the tool with respect and caution to
lessen the possibility of mechanical damage
or operator injury. As with all power tools,
there is danger associated with the Model
W1679. If normal safety precautions are
overlooked or ignored, injury to the opera-
tor or others in the area is likely.
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
48
29
1
30
43
16
13
14
38
11
35
15
36
12
37
39
34
19
24
27
28
1
6
5
1
3
4
10
1
25
24
33
9
8
42
32
31
50
7
21
26
44
46
22
45
51ꢀ
2
23
(optionalꢀ
220V)
18
53
40B
47
49
40
40A
1
54
52
18
41
17
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
XPW07
XPB21
X1679003 MOTOR PULLEY
XPVA36 V-BELT A-36
XPK12M KEY 5 x 5 x 30L
FLAT WASHER 5⁄16"
43 X1679043 CORD
44 X1679044 CABLE CLAMP
HEX BOLT 3⁄8"-16 x 3⁄4
"
45 X1679045 BOTTOM COLOR STRIPE
46 X1679046 LOGO SHOP FOX
47 X1679047 MACHINE ID/WARNING LABEL
48 X1679048 ELECTRICITY LABEL
49 X1679049 SAFETY GLASSES LABEL
50 X1679050 READ MANUAL LABEL
XPB03
HEX BOLT 5⁄16"-18 x 1"
X1679007 CABINET STAND
X1679008 KNOB 3⁄8"-16 x 11⁄2
XPN08
"
HEX NUT 3⁄8"-16
51 X1679051 MAGNETIC SWITCH 220V
52 X1679052 WIRE GROMMET
(OPTIONAL)
10 XPWR810 WRENCH 8/10MM
11 X1679011 SWITCH BOX
12 X1679012 CONTROL PANEL
13 X1679013 FLEXIBLE WIRE(BLACK)
14 XPS01
PHLP HD SCREW 10-24 x 1⁄2
15 X1679015 MOTOR ON PILOT LIGHT
16 XPWRCRD110S MOTOR CORD
17 X1679017 PHILLIPS HD FLANGE SCREW
18 XPN07 HEX NUT 10-24
53 W1001
54 XPS38
DUST PORT
PHLP HD SCR 5⁄16"-18 X 1⁄2
"
101 X1679101 PIVOT STUD 1⁄2"-20 x 3⁄4
"
"
102 X1679102 SPECIAL SCREW 3⁄8"-16 x 11⁄2
103 X1679103 TILT LEVER
104 X1679104 SPECIAL SCREW 5⁄16"-18 X 13⁄4
105 X1679105 FENCE STOP BRACKET
"
"
106 XPN19
HEX NUT 7⁄16"-14
19 X1679019 WIRE CONNECTOR
20 X1679020 NYLON CABLE TIE
21 XPS08
107 X1679107 FENCE TILT CLAMP
108 XPRP18M ROLL PIN 4 x 12L
109 X1679109 STOP TAB
PHLP HD SCREW 10-24 x 3⁄4
"
22 X1679022 UPPER COLOR STRIPE
110 X1679110 FENCE TILT SLEEVE
23 XPHTEK10 SELF TAPPING SCREW #4 x 3⁄8
"
111 X1679111 LOCKING SCREW 1⁄2"-12 X 33⁄4
"
24 XPN02
25 XPCB01
26 XPW02
27 XPSS03
HEX NUT 5⁄16"-18
112 XPN02
HEX NUT 5⁄16"-18
CARRIAGE BOLT 5⁄16"-18 x 5⁄8
"
113 X1679113 FENCE LOCK BRACKET
FLAT WASHER 3⁄8
SETSCREW 1⁄4"-20 x 3⁄8
"
114 XPW06
115 XPN01
FLAT WASHER 1⁄4
HEX NUT 1⁄2"-20
"
"
28 X1679028 MOTOR 1HP
29 XPB32
116 X1679116 FENCE
HEX BOLT 5⁄16"-18 x 5⁄8
"
117 X1679117 FENCE HINGE
30 XPWRCRD110L POWER CORD
31 X1679031 CABINET DOOR
32 X1679032 LATCH
118 XPN08
119 X1679119 KNOB 3⁄8
120 X1679120 FENCE BRACKET
HEX NUT 3⁄8"-16
"
33 XPW02
FLAT WASHER 3⁄8
"
121 X1679121 SPECIAL SCREW 5⁄16"-18 X 11⁄4
122 X1679122 FENCE ADJUSTMENT ROD
123 X1679123 90º STOP
"
34 XPAW03M ALLEN WRENCH 3MM
35 X1679035 PEDESTAL ARM
36 X1679036 FLEXIBLE WIRE(YELLOW)
37 X1679037 CABLE MARKER
38 X1679038 EMERGENCY STOP SWITCH
39 X1679039 ON SWITCH
40 X1679040 MAGNETIC SWITCH 110V
40A X1679040A FRONT SWITCH COVER
40B X1679040B REAR SWITCH COVER
124 X1679124 SPECIAL BOLT 5⁄16"-18 X 5⁄8
125 XPN09
HEX NUT 5⁄8"-18
126 X1679126 FENCE BASE
"
127 XPB03
128 XPB22
129 XPS07
HEX BOLT 5⁄16"-18 x 1"
HEX BOLT 5⁄16"-18 x 13⁄4
PHLP HD SCREW 1⁄4"-20 x 3⁄8
"
"
130 X1679130 SUPPORT
131 XPW01
FLAT WASHER 1⁄2
132 X1679132 SPECIAL NUT 1⁄2"-12
41 XPW03
FLAT WASHER #10
"
42 X1679042 STRAIN RELIEF 1⁄2
"
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
216
241
214
227
240
240
215
204
208
242
234
249
224
250
220
225
230
243
205
231
212
232
207
219
206
233
245
246
222
209
221
203
248
213
229
201
226
217
228
204
235
210
239
238
222
248
219
212
244
236
218
211
206
231
205
237
246
230
202
225
220
246
224
233
249
245
250
-36-
Download from Www.Somanuals.com. All Manuals Search And Download.
316
315
301
306
311
310
307
314
303
312
310
302
304
305
309
313
317
317
303
312
304
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
201 X1679001 INFEED TABLE
202 X1679002 GIB
203 XPSS01
235 X1679235 SPRING PLATE
236 X1679236 SPRING HOUSING
237 XPS25
SETSCREW 5⁄16"-18 x 1"
PHLP HD SCREW 8-32 x 5⁄8
"
204 X1679004 TABLE ADJUST ROD
238 X1679238 SCALE
239 X1679239 RIVET
240 XPB24
205 XPSS11
206 X1679006 LEAD SCREW
207 XPW07
FLAT WASHER 5⁄16"
208 X1679008 CUTTERHEAD WARNING LABEL
209 X1679009 STUD
SETSCREW 1⁄4"-20 x 1⁄4
"
HEX BOLT 3⁄8"-16 x 11⁄4
"
241 X1679241 FENCE SUPPORT KEY
242 XPW02
243 XPB23
FLAT WASHER 3⁄8
"
HEX BOLT 5⁄16"-18 x 21⁄2
"
210 X1679010 SPRING
244 X1679244 LOCK HANDLE 5⁄16"-18 x 1-1⁄4
"
211 X1679011 HOUSING MOUNT
212 XPSB03
245 XPW03
246 XPW01
FLAT WASHER #10
CAP SCREW 5⁄16"-18 x 1"
FLAT WASHER 1⁄2
"
213 X1679013 POINTER
247 X1679247 CAUTION CARD
248 XPW06
FLAT WASHER 1⁄4
249 X1679249 KNOB
250 XPB22
301 D3165
214 X1679014 FENCE SUPPORT
"
215 XPW02
216 X1679016 SPRING PIN
217 XPS23
PHLP HD SCREW 8-32 x 1⁄4
218 X1679018 LABEL
FLAT WASHER 3⁄8
"
HEX BOLT 5⁄16"-18 x 13⁄4
KNIVES SET OF THREE
"
"
302 X1679302 KNIFE GIB
219 XPW07
220 XPS01
FLAT WASHER 5⁄16"
PHLP HD SCREW 3⁄16"-24 x 1⁄2
303 XPN11
HEX NUT 3⁄8"-24
"
304 X1679304 STUD
221 XPSS31M SETSCREW M5-.08 x 8
222 XPB57
223 W1400
305 XP6202
306 XP6203
307 X1679307 PULLEY
BEARING 6202-2RS
BEARING 6203-2RS
HEX BOLT 1⁄4"-20 x 1⁄4
PUSH BLOCK
"
224 X1679024 SPACER
225 XPN02
226 X1679226 BASE
308 X1679308 KNIFE SETTING GAUGE
309 X1679309 CUTTER HEAD
310 X1679310 SPRING
HEX NUT 5⁄16"-18
227 X1679227 OUTFEED TABLE
228 X1679228 TABLE LOCK HANDLE
229 XPN02
230 X1679230 HANDWHEEL
231 X1679231 LOCK COLLAR
232 X1679232 BELT GUARD
233 X1679233 LEAD SCREW BRACKET
234 X1679234 CUTTERHEAD GUARD
311 X1679311 GIB BOLT
312 XPLW03 LOCK WASHER #10
313 X1679313 BEARING BLOCK
314 XPK23M KEY 5 x 5 x 25MM
315 X1679315 BEARING BLOCK
HEX NUT 5⁄16"-18
316 XPSS03
317 X1679317 FLAT HD ALLN SCR 10-24 X 1⁄2
SETSCREW 1⁄4"-20 x 3⁄8
"
"
-38-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name __________________________________________________________________________________________
Street __________________________________________________________________________________________
City ____________________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_________________________________FAX___________________
MODEL #______________________________ Serial #___________________________________________________
The following information is given on a voluntary basis and is strictly confidential.
1.
2.
Where did you purchase your Shop Fox® machine?
10.
What stationary woodworking tools do you own? Check all that apply.
_________________________________________________________
___Air Compressor
___Band Saw
___Panel Saw
___Planer
How did you first learn about us?
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Spindle Sander
___Table Saw
___Drum Sander
___Dust Collector
___Horizontal Boring Machine
___Jointer
___Advertisement
___Friend
___Mail order Catalog
___World Wide Web Site
___Local Store
___Lathe
___Mortiser
___Vacuum Veneer Press
___Wide Belt Sander
___Other__________________________________________________
Which of the following magazines do you subscribe to.
___Other__________________________________________________
3.
11.
12.
13.
Which benchtop tools do you own? Check all that apply.
___American Woodworker
___Cabinetmaker
___Today’s Homeowner
___Wood
___1" x 42" Belt Sander
___5" - 8" Drill Press
___8" Table Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Mini Jointer
___6" - 8" Grinder
___Mini Lathe
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
___Wooden Boat
___Woodshop News
___Woodsmith
___Woodwork
___Journal of Light Construction
___Old House Journal
___Popular Mechanics
___Popular Science
___Woodworker
___Woodworker’s Journal
___Workbench
___Other__________________________________________________
___American How-To
Which portable/hand held power tools do you own? Check all that apply.
___Popular Woodworking
___Other__________________________________________________
Which of the following woodworking/remodeling shows do you watch?
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Miter Saw
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
4.
5.
6.
___Backyard America
___Home Time
___The New Yankee Workshop
___This Old House
___The American Woodworker
___Woodwright’s Shop
___Other__________________________________________________
___Other__________________________________________________
What is your annual household income?
What machines/supplies would you like to see?
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
14.
15.
16.
What new accessories would you like Woodstock International to carry?
_________________________________________________________
_________________________________________________________
What is your age group?
Do you think your purchase represents good value?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
___Yes
Would you recommend Shop Fox® products to a friend?
___Yes ___No
___No
7.
8.
9.
How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
17.
Comments:________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
How would you rank your woodworking skills?
___Simple
___Advanced
___Master Craftsman
___Intermediate
How many Shop Fox® machines do you own? _____________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL, INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|