MODEL W1795/W1801
DELUXE SPRAY GUN
W1795
W1801
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: [email protected]
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9625TR PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are intended
to convey the level of importance of the safety messages. The progression of
symbols is described below. Remember that safety messages by themselves do not
eliminate danger and are not a substitute for proper accident prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful
NOTICE
information about proper operation of the
equipment.
Safety Instructions for Pneumatic Tools
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking
to see that keys and adjusting
wrenches are removed from tool
before operation.
6. MAKE WORKSHOP CHILD PROOF by
locking your shop and shutting off
air valves.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a
job for which it was not designed.
pneumatic tools in damp or wet
locations, or where any flammable
or noxious fumes may exist. Keep
work area well lighted.
9. DO NOT USE UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL.
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
Safety Instructions for Pneumatic Tools
17. DISCONNECT TOOLS before
servicing, changing accessories, or
moving to another location.
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without
stretching.
18. DO NOT OVERREACH. Keep proper
footing/balance at all times.
11. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or
other jewelry which may get
caught in moving parts. Non-slip
footwear is recommended. Wear a
protective hair covering to contain
long hair.
19. USE THE RECOMMENDED
ACCESSORIES. Consult owner’s
manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
20. CHECK FOR DAMAGED PARTS
BEFORE USING. Check for binding
and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that may
affect tool operation. Repair or
replace damaged parts.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask
if cutting operation is dusty.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
21. NEVER LEAVE UNATTENDED TOOL
CONNECTED TO AIR. Disconnect
the air hose and do not leave tool
until it is relieved of any built up
pressure.
13. WEAR APPROVED HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL WHILE
UNSUPERVISED.
14. SECURE WORK. Use clamps or a
vise to hold work when practical.
It is safer than using your hand
and frees both hands to operate
tool.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING TOOL. Seek formal training
or research books or magazines
that specialize in pneumatic tools.
15. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
24. BE AWARE OF HOSE LOCATION
WHEN USING PNEUMATIC TOOLS.
Hoses can easily become a tripping
hazard when laid across the floor
or spread out in a disorganized
fashion.
16. REDUCE THE RISK OF
UNINTENTIONAL FIRING. Do not
carry tool with hand on trigger
and always disconnect from air
when not in use.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
Additional Safety Instructions for Spray Guns
1. READ THIS MANUAL. This manual
contains proper operating
8. PROTECTIVE CLOTHING. Protect
exposed skin from overspray by
wearing a protective suit or other
approved garment.
instructions for this spray gun.
2. READ MATERIAL LABELS and
MATERIAL SAFETY DATA SHEETS
(MSDS). Read and know all the
instructions on the packaging label
and the MSDS before opening the
package. This information could
save your life.
9. UNSAFE USE. DO NOT point
or shoot spray gun directly at
yourself or another person or
animals. Do not attempt to use
the spray gun for any other use
than it was intended.
3. ALWAYS WEAR A NIOSH
APPROVED RESPIRATOR WHEN
SPRAYING OR WORKING AROUND
FINISHING MATERIALS.
10. STORAGE. Thoroughly clean and
dry spray gun before storage.
Store in an approved cabinet.
11. SOLVENTS. Always store solvents
and shop towels soaked in solvent
in approved containers.
4. FIRE EXTINGUISHERS. Always
have a fully charged multi class
or class B fire extinguisher in the
immediate area.
12. EYE PROTECTION. Wear eye
protection whenever spraying or
cleaning. Solvents and chemicals
can cause serious eye injury,
which could lead to blindness.
5. FLAMMABLE MATERIAL. NEVER
spray near open flame or where
any spark could occur.
13. OPERATING PRESSURE. DO NOT
exceed the recommended inlet air
pressure. Excessive pressure could
cause the spray gun to burst or
cause other internal equipment
damage.
6. FRESH AIR. Always provide
adequate exhaust to keep area
free of built up vapors, NEVER
spray in an enclosed space.
7. DISCONNECT COMPRESSED AIR.
Always disconnect the spray
14. LOCAL LAWS. Consult local
authorities regarding ventilation
and waste disposal requirements.
gun from compressed air before
cleaning, changing attachments or
when performing maintenance of
any kind on this tool.
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies to your individual working conditions. Use
this and other tools with caution and respect to avoid serious injury.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
INTRODUCTION
Woodstock Technical
W1795 Specifications
Support
Type.......................HVLP Gravity Feed
Fluid Tip............................... 1.4 mm
Acceptable Nozzle Range.......1.3–2.5 mm
Air Consumption ................ 4.2–7.1 CFM
Inlet Air Pressure ..... 2–3.5 Bar /29–51 PSI
Fluid Pressure .......................... 10 PSI
Pattern Width ...................180-250 mm
Material Capacity ..................... 600 ml
This tool has been specially designed to
provide many years of trouble-free ser-
vice. Close attention to detail, ruggedly
built parts and a rigid quality control pro-
gram assure safe and reliable operation.
Woodstock International, Inc. is commit-
ted to customer satisfaction. Our intent
with this manual is to include the basic
information for safety, setup, operation,
maintenance, and service of this product.
W1801 Specifications
Type.......................HVLP Gravity Feed
Fluid Tip............................... 1.4 mm
Acceptable Nozzle Range.......1.3–2.5 mm
Air Consumption ................ 4.2–7.1 CFM
Inlet Air Pressure ..... 2–3.5 Bar /29–51 PSI
Fluid Pressure .......................... 10 PSI
Pattern Width ...................180-250 mm
Material Capacity ..................... 600 ml
We stand behind our tools! In the
event that questions arise about
your tool, please contact Woodstock
International Technical Support at
(360) 734-3482 or send e-mail to:
[email protected]. Our knowl-
edgeable staff will help you troubleshoot
problems and process warranty claims.
If you need the latest edition of this
manual, you can download it from
If you have comments about this
manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation
Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [email protected]
Read manual before operation.
Become familiar with the spray gun
safety and operation instructions
before beginning any work. Serious
personal injury may result if safety
or operational information is not
understood or followed.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
SETUP
Unpacking
This tool has been carefully packaged for safe transportation. If you notice the tool
has been damaged during shipping, please contact your authorized Shop Fox dealer
immediately.
Inventory
The following is a description of the main components shipped with the Model W1795/
W1801. Lay the components out to inventory them.
Note: If you can't find an item on this list, check the mounting location on the tool
or examine the packaging materials carefully. Occasionally we pre-install certain
components for safer shipping.
W1795 Inventory (Figure 1)
Qty
W1801 Inventory (Figure 2)
Qty
A. Spray Gun . .............................. 1
B. Cup 600 ml............................... 1
C. Cleaning Brush........................... 1
D. Service Wrench.......................... 1
E. Filters..................................... 2
F. Baffle Wrench ........................... 1
A. Spray Gun . .............................. 1
B. Cup 600 ml............................... 1
C. Cleaning Brush........................... 1
D. Service Wrench.......................... 1
E. Filters..................................... 2
F. Baffle Wrench ........................... 1
E
B
B
A
C
A
D
F
E
D
F
C
Figure 1. Model W1795 inventory.
Figure 2. Model W1801 inventory.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
Assembly
1. Insert the filter into the gun body
(see Figure 3).
Controls
Atomizing Cap
Cup
Fluid Control
Trigger
Pattern
Control
Air Flow Control
Figure 4. Controls.
1. Fluid Control: Controls the volume
of material that travels through the
fluid tip.
Figure 3. Installing filter.
2. Pattern Control: Adjusts the spray
pattern from a round pattern to a
wide fan.
2. Screw the cup onto the top of the
body.
3. Air Flow Control: Controls the fluid
3. Install the barbed hose fitting into
the base of the gun handle and tight-
en in place with the lock nut.
pressure inside the spray gun.
4. Atomizing Cap: Controls the spray
pattern from vertical to horizontal.
4. Secure the air hose to the barbed fit-
ting with a hose clamp.
5. Trigger: Two stage trigger. Stage
one only releases compressed air for
blowing off the work piece. Stage two
sprays material.
1
Note: Using a ⁄4" NPS quick discon-
nect set-up (not included), will make
operation and maintenance tasks eas-
ier.
6. Material Cup: Holds the paint to be
sprayed.
5. Attach the spray gun to an air hose
regulated between 43.5 and 58 PSI.
Note: For the best results, use a hose
that will be dedicated for spray use
only. Do not use a hose that has been
used with an in-line oiler or other
possible contaminant.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
OPERATIONS
Spraying
The Model W1795/W1801 spray gun is
designed to spray low to medium solid
materials, like lacquers, stains, primers,
multi-component paints, acrylics, epoxies
etc. It is ideal for auto body touch-ups,
woodworking projects, or projects with
hard to reach areas. It is not for use with
any waterborne material.
EXPLOSION HAZARD! DO NOT smoke
or have any source of flame or spark
near spraying. Vapors will explode if
ignited.
To use your spray gun:
1. Read and follow the material
manufacturer's instructions for
spraying, mixing, safety, disposal,
and any other instruction on the label
or Material Safety Data Sheet (MSDS).
2. Ensure the cup is securely tightened
and all other fittings are secure to
avoid air leaks or material spills.
RESPIRATORY HAZARD! Always use
respirator rated for organic vapor and
solvent use when using spray equip-
ment. Failure to protect your lungs
can lead to respiratory illness and
nervous system damage.
3. Set the inlet air pressure (the air
coming to the spray gun) to the
lowest pressure recommended
in Specifications on Page 4 or
to the material manufacturer's
recommendations.
4. Adjust the atomizing cap to vertical
or horizontal. See Atomizing Cap
and Fan Adjustments on Page 9 for
further explanation.
5. Fill the cup with material.
6. Trial and error are necessary to
achieve the results you want along
with a fair amount of practice. Test
your material flow and spray pattern
on a piece of cardboard or some
scrap of material similar to your
project.
TOXIC FUMES! Always use an approved
spray booth or well ventilated area
when spraying. NEVER spray in an
confined space where toxic fumes
and flammable vapors can accumu-
late to deadly levels.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
7. Adjust the fluid control knob to
start with a low volume of material
and keep the atomization as low
as possible. You will need to use a
combination of fluid control, inlet air
pressure, air flow control and stroke
speed to achieve the results you
want. Spray so the material wets out
nicely without running or sagging.
10. Begin spraying 2-3 inches before the
work and continue to the end of the
work. Continue the motion for a few
inches past the work until you are
ready for the return stroke.
11. Maintain an even speed when
spraying.
12. Overlap each stroke by 50%. This will
ensure even coverage as shown in
Figure 6. Overlapping less than 50%,
as shown in the figure to the right,
may lead to missed spots or streaky
results.
8. Use the pattern control knob to
adjust the spray fan to your desired
pattern.
9. Keep the gun tip perpendicular,
parallel, and 6-8" from the work (as
shown in Figure 5) when spraying.
Do not allow your wrist to bend. This
will cause the gun to arc across the
surface and distribute the material
unevenly, possibly creating sags and
dry spots.
Yes
No
Figure 6. Overlap technique.
��
��
13. Spray stroke should have even
consistency and parallel edges. If it
doesn't, refer to Troubleshooting on
Page 12.
NOTICE
Figure 5. Spray technique.
Tipping spray gun may cause material
to spill out of the cup. Always hold
the spray gun perpendicular to the
ground to avoid potential spills and
gravity feed problems.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
Rotating the pattern adjustment control
in Figure 8 will give you a range between
the two patterns in Figure 9.
Atomizing Cap and Fan
Adjustments
The atomizing cap needs to be adjusted
for horizontal or vertical spraying
patterns. Spraying in the wrong direction
may lead to material build up on the
atomizing cap horn. Many performance
problems are caused by clogged
Stroke
atomizing holes on the atomizing cap
horns (see Cleaning on Page 10).
Pattern
Pattern Control
Figure 8. Set up for horizontal spray
stroke with vertical fan pattern.
Pattern
Stroke
Pattern Control
Figure 7. Set up for vertical stroke direc-
tion with horizontal fan pattern.
Figure 9. Fan adjustment.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
CLEANING & LUBRICATION
5. Unscrew the atomizing cap with
your fingers and the fluid tip with
the service wrench. The fully
disassembled gun should look like
Figure 10.
Cleaning
Proper cleaning is the best way to ensure
trouble free performance from your spray
gun. If your gun is not thoroughly cleaned,
damage and poor spraying will result.
Problems caused by improper cleaning will
not be covered by the warranty. Clean the
spray gun immediately after each use.
6. Rinse these parts thoroughly in
solvent then dry with compressed air
or let air dry.
To clean your spray gun:
Note: If the small holes in the
atomizing cap become blocked, soak
in clean solvent. If the blockage
still exists, clear the blockage with
a small needle, taking great care
not to enlarge or damage the hole.
Damage to the hole will create a
disrupted spray pattern.
1. Spray a small amount of solvent
through the spray gun.
Note: Check with local laws
regarding this practice. If you are
spraying on a regular basis, spraying
solvents into the air may be illegal. A
cabinet style spray gun cleaner may
be required.
7. Use the cleaning brush with solvent
to clean the inner orifice and other
hard to reach areas on the outside of
the spray gun body.
2. DISCONNECT SPRAY GUN FROM AIR!
3. Unscrew the cup.
8. Wipe the rest of the gun body with a
shop towel and dry.
4. Disassemble the gun by unscrewing
the fluid control knob, removing the
spring and needle (Figure 10).
EXPLOSION HAZARD! Chlorinated
Solvents like Tricloroethane and
Methylene Chloride (methyl chlo-
ride) can chemically react with alu-
minum and may explode. Many parts
in spray guns are made of aluminum.
Read solvent label carefully before
using solvent.
Cup
Filter
Fluid Tip
Needle
Fluid
Control
Knob
Atomizing
Cap
Spring
NOTICE
DO NOT soak the spray gun body
in solvent. Prolonged exposure to
solvent will rapidly deteriorate the
spray gun washers and seals. Ignoring
this notice will void your warranty.
Figure 10. Disassembled for cleaning.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
Lubrication
Lubricate the following areas with
spray gun lube after cleaning:
A
A. Atomizing Cap Threads
B. Air Valve Packing
C. Trigger Pin
D. Air Flow Control Valve
E. Pattern Control
F
B
C
E
D
F. Fluid Control Knob
Figure 11. Lubrication points.
After each cleaning, apply a thin film
of petroleum jelly to the needle spring
before reassembling.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
Troubleshooting
Symptom
Possible Cause
Possible Solution
1. Tighten fluid tip or replace
seat with new one.
Fluttering or
1. Dry or worn fluid tip seat
permits air to seep into fluid
passage.
Spitting spray.
2. Material level too low.
3. Fluid tip or filter obstructed.
4. Dry needle packing.
2. Add material.
3. Clean.
4. Lubricate needle.
1. Clear holes.
Uneven top or bot- 1. Atomizing cap holes are
tom pattern.
obstructed.
2. Build-up on top or bottom of
fluid tip.
3. Build-up on atomizing cap is
on needle seat.
2. Clean.
3. Clean.
Right or left arc
pattern.
1. Left or right side horn holes
are plugged.
2. Build-up on left or right side
of fluid tip.
1. Clear holes.
2. Clean.
3. Build-up of material inside
atomizing cap.
3. Clean.
Heavy deposit of
material in center.
1. The material flow exceeds
the atomizing cap capacity.
2. Inlet air pressure is too low.
3. Material is too thick.
1. Lower fluid flow.
2. Increase inlet air pressure.
3. Thin material.
Narrow center pat- 1. Volume control turned in too
1. Increase volume.
tern.
far.
2. Inlet air pressure too high.
2. Reduce inlet air pressure.
3. Increase fluid pressure.
4. Adjust material.
3. Fluid pressure is too low.
4. Material is too thin.
No spray output.
1. No pressure at gun.
2. Fluid passages dirty.
1. Check air supply.
2. Clean gun, remove any
obstructions.
3. Fluid control closed.
4. Out of paint.
3. Open.
4. Refill.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
Symptom
Excessive over-
spray.
Possible Cause
Possible Solution
1. Reduce fluid pressure.
2. Keep gun at recommended
distance.
1. Fluid pressure too high.
2. Gun is too far from surface.
3. Spraying too fast.
3. Slow down and maintain
consistent, even parallel
stroke.
Unable to control
spray fan.
1. Pattern adjustment screw is
not seating properly.
1. Clean or replace.
2. Atomizing cap is loose.
2. Tighten atomizing cap.
1. Replace damaged seals.
Runs and sags.
1. Damaged seal.
Material leaks from 1. Cap not secure.
cup. 2. Cup not tight on gun body.
3. Leaking from cap vent hole.
1. Tighten.
2. Tighten.
3. Hold gun upright do not
tilt.
Material leaks from 1. Fluid tip loose.
1. Tighten.
gun.
2. Dry or damaged seals.
3. Excessive pressure.
2. Replace seals.
3. Reduce pressure.
Thick dimpled fin-
ish aka "Orange
Peel."
1. Holding gun too close to sur-
face.
2. Inlet air pressure too low.
3. Material not properly mixed.
1. Spray at recommended dis-
tance.
2. Check inlet air pressure.
3. Follow manufacturer's
instructions.
4. Surface is dirty or oily.
4. More surface prep is
required.
Dry Spray.
1. Inlet air pressure too high.
2. Gun too far from surface.
1. Lower inlet air pressure.
2. Keep gun at recommended
distance.
3. Gun stroke too fast.
3. Slow down and maintain
consistent even parallel
stroke.
Gun leaks from
fluid tip.
1. Debris will not let the needle 1. Clean or replace both.
seat with the fluid tip.
Contaminated
paint.
1. Water or oil in the air line.
1. Install an in-line air filter.
2. Replace air line.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
PARTS BREAKDOWN
�
�
�
�
��
��
��
��
�
��
��
��
��
��
��
��
��
�
��
��
��
��
��
��
�
�
�
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1795/W1801 Deluxe Spray Gun
PARTS LIST
REF PART�# DESCRIPTION
REF PART�# DESCRIPTION
27 X1795027 AIR�ADJ.�SCREW
28 X1795028 BRUSH
1
2
3
4
5
6
7
8
9
XPEC02M E-CLIP�4MM
XPEC02M E-CLIP�4MM
X1795003 TRIGGER
29 X1795029 HEX�SOCKET�TOOL
30 X1795030 MULTI-TOOL�WRENCH
31 X1795031 AIR�INLET�PLUG
32 XPEC09M E-CLIP�6MM
X1795004 TRIGGER�PIN�II
X1795005 TRIGGER�PIN�I
X1795006 COMPRESSION�SPRING
X1795007 DOMED�SEAL�WASHER
X1795008 DIRECTION�SCREW
X1795009 SEAL�WASHER�10MM
33 X1795033 O-RING�6�X�2
34 X1795034 PATTERN�ADJ.�SCREW
35 X1795035 COPPER�WASHER�8MM
36 X1795036 PATTERN�ADJ.�KNOB
37 X1795037 PATTERN�ADJ.�KNOB
38 XPF04M FLAT�HD�SCR�M6-1�X�8
39 X1795039 FLUID�ADJ.�KNOB
40 X1795040 JOINT�CAP
10 X1795010 FLUID�NOZZLE�PLUG
11 X1795011 FLUID�NOZZLE
12 X1795012 ATOMIZING�CAP
13 X1795013 SEAL�WASHER�30MM
14 X1795014 NOZZLE�NUT
15 X1795015 LOCKED�SPRING
16 X1795016 DIRECTION�SCREW
17 X1795017 DOMED�SEAL�WASHER
18 X1795018 O-RING�8.5�X�1.2
19 X1795019 SWITCH�KNOB
20 X1795020 AIR�VALVE�BODY
21 X1795021 SWITCH�SPRING
22 X1795022 AIR�INLET�VALVE
23 X1795023 AIR�ADJ.�SPRING
24 X1795024 DOMED�SEAL�WASHER
25 X1795025 O-RING�2.5�X�1.2
26 X1795026 AIR�ADJ.�KNOB
41 X1795041 FLUID�NEEDLE�SPRING
42 X1795042 FLUID�ADJ.�NEEDLE
43 X1795043 HANGER
44 X1795044 FLUID�INLET�JOINT��
45 X1795045 FLUID�INLET�JOINT�SEAL
46 X1795046 FILTER
47 X1795047 ALUMINUM�CUP�(W1795)
47 X1801047 PLASTIC�CUP�(W1801)
48 X1795048 ALUMINUM�COVER�(W1795)
48 X1801048 PLASTIC�COVER�(W1801)
49 X1795049 BREATHER�PLUG
50 X1795050 COMPLETE�O-RING�SET
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects
from workmanship and materials for a period of two years from the date of original
purchase by the original owner. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or
reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option,
the Shop Fox machine or machine part which in normal use has proven to be defective,
provided that the original owner returns the product prepaid to a Shop Fox factory
service center with proof of their purchase of the product within two years, and
provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty,
then the original owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties
that may be implied by law, including any merchantability or fitness, for any particular
purpose, are hereby limited to the duration of this written warranty. We do not
warrant that Shop Fox machinery complies with the provisions of any law or acts. In
no event shall Woodstock International, Inc.'s liability under this warranty exceed the
purchase price paid for the product, and any legal actions brought against Woodstock
International, Inc. shall be tried in the State of Washington, County of Whatcom. We
shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special or consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality
and durability standards. We reserve the right to change specifications at any time
because of our commitment to continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Registration
Name___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________State___________________________Zip________________________
Phone #______________________Email __________________________Invoice #___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
_____ Advertisement
____ Friend
____ Website
____ Local Store
____ Other:
_____ Mail Order Catalog
2. How long have you been a woodworker/metalworker?
_____ 0-2 Years
_____ 2-8 Years
____8-20 Years
_____ 20+ Years
3. How many of your machines or tools are Shop Fox?
_____ 0-2
_____ 3-5
____6-9
_____ 10+
____ No
____ No
4. Do you think your tool represents a good value?
_____ Yes
5. Would you recommend Shop Fox products to a friend? _____ Yes
6. What is your age group?
_____ 20-29
_____ 50-59
____ 30-39
____ 60-69
____ 40-49
____ 70+
7. What is your annual household income?
_____ $20,000-$29,000
_____ $50,000-$59,000
____ $30,000-$39,000
____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
8. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Old House Journal
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Shotgun News
9. Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
___________________________________________________________________
___________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|