®
Instruction Manual for DISH Users
For receivers and programming, call 1-866-609-9374
For up-to-date information on receiver compatibility and
For help, email [email protected] or call 1-800-788-4417
Do not return antenna to place of purchase
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts of the Antenna
Antenna in Deployed Position
Supports up to two receivers
Reflector cover
Protects inner components
from environment
Includes 25 ft power cable
and 25 ft coaxial cable
Follow the instructions on this side of the manual if setting up the Anser® antenna
for use with DISH programming. If setting up the Anser for use with DIRECTV
Programming, follow the instructions on the reverse side of the manual.
Unit weight: 16 lbs
Secondary port
Connects to
secondary receiver
(or dual tuner)
Stowed height: 15 in
Elevation lock
Secures rotating housing
at desired elevation
Main port
Connects to
primary receiver
Max. height deployed: 20.75 in
Diameter: 21 in
Before Installing the Antenna
Congratulations on purchasing the Winegard® Carryout® Anser antenna! The Anser antenna is a portable satellite
system that requires a user elevation setting to automatically acquire the desired satellite. As the user, you will
need to know which satellite you would like to view and the corresponding elevation angle for that satellite. Under
“Compatible Satellites,” different popular satellite options are outlined along with the programming offered via each
satellite. Elevation and coverage maps are also included to help you determine the correct elevation angle and
coverage for certain satellites.
Quick disconnect socket
Connects to power source
Reflector size: 18 in
Elevation range: 15–65°
UV-protected plastic reflector cover
Max amperage: 5.0 A
Antenna in Stowed Position
The Anser antenna requires the following simple steps before operation:
1. Find elevation angle via receiver menu or provided maps*.
2. Hook up the antenna, and manually set the elevation to the correct elevation angle for your area.
3. Get to the signal meter screen on your receiver.
4. Plug in the unit—the unit will search and find the strongest signal.
5. If the system stops on a signal but is not on the desired satellite for viewing, the unit will move to the next signal
found in 45 seconds. Once you have signal on your desired satellite, unplug the power to the unit.
6. Watch TV!
Rotating housing
Rotates to desired
elevation setting
Unit operating voltage: 10.5–13.8 V
Supply voltage: 12–13.8 V
Gray plastic base
Handle
Enables easy
carrying of antenna
*Elevation angles may not be displayed in the receiver menu for satellite 72° (recommended as a single satellite
solution for DISH® HD programming) or 129°. If the elevation angle is not displayed in the receiver menu, use the
provided elevation and coverage maps to find the elevation angle for your current location.
Elevation housing
Includes elevation
markings for
Eyelet
Enables securing of
antenna to site
easy pointing
Compatible Satellites
Receivers
Antenna Feet
The antenna has four feet on
the bottom of the unit. Each foot
has two mounting spots on the
underside of the antenna. The
antenna will come with the feet in
the inside holes.
Feet in inside holes
Feet in outside holes
72°: Eastern satellite, recommended
82°: HD programming
91°: Standard programming
The 72° and 129° satellites require
an HD receiver.
for HD programming
129°: Western satellite, majority of
HD programming
If mounting the antenna on
119°: Majority of std. programming
Winegard Model TR-1518 tripod,
mount the feet in the inside holes.
The 72° satellite is recommended as a single satellite solution for
TIP
DISH® HD programming. In the Northwest, the extremely low elevation
110°: Some standard programming,
limited HD programming
angle may present issues in getting clear line-of-sight to the satellite. In those
circumstances, use one of the western satellites (110°, 119°, or 129°). Note
that the 72° and 129° satellites require an HD receiver.
For extra support, mount the feet in
the outside holes.
Also compatible: Satellites 61.5° & 77°
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
DISH Receiver Setup
DISH receivers will often not show when they are on signal if they have
incorrect “Check Switch” information. For this reason, DISH users must clear
their current settings before pointing. To do this for most DISH receivers,
follow the steps below. The following instructions are based on a Solo ViP®
211k receiver. If your receiver differs from the options shown, consult your
receiver manual.
Check out online receiver
setup guides for your
receivers/setupguide.php.
The Carryout Anser antenna is meant for stationary use only and will not function while in motion. The Anser antenna
is not intended for permanent mounting on any vehicle.
TIP
The Anser antenna is not meant for use with the Carryout ladder mount. Installing the antenna on the Carryout ladder
mount may lead to serious injury and/or equipment and property damage.
Do not install or operate the antenna in winds of 35 mph or greater. The Anser antenna will roll in winds ≥35 mph.
Do not place the antenna in water >2 inches deep, or the water may damage the electronics.
Before starting receiver setup, make sure the coaxial cable is disconnected from “Sat In” on the back of the receiver.
Care should be taken when transporting and setting up the Anser antenna. Do not toss or drop the antenna.
Do not paint this antenna. Painting the antenna may cause signal degradation and will void your warranty.
1
2
3
Selecting a Location for the Antenna
Choose a location with a clear, unobstructed view of the southern sky. Avoid obstructions such as trees, hills,
vehicles, or buildings—these can block the signal from the satellite.
Press “Menu” on your remote.
Select option 6, “System Setup.”
Select option 1, “Installation.”
Select option 1, “Point Dish.”
Make sure the antenna is not placed in the path of people or vehicles; otherwise, the antenna may be knocked off of
the signal if run into, or cables may be disconnected from the unit.
Try to select a location that will allow the Carryout Anser antenna to sit within three degrees of level.
Satellite signal will not
6
4
5
NOTE
pass through solid objects.
For this reason, it is vital to select a
location with a clear, unobstructed
view of the southern sky.
A 25 foot power cable and
NOTE
25 foot coaxial cable are
included with the antenna. Keep this
in mind when selecting a location
for the antenna.
Select “Check Switch.” (Make sure
the coaxial cable is disconnected
from “Sat In” on the back of the
receiver before proceeding.)
Make sure that there are no
checkmarks by “SuperDISH” or
“Alternate.” Select “Test.”
The receiver will go through a
number of steps to detect your
satellite settings.
Finding the Elevation Angle for the Current Location
7
8
9
Find the elevation angle for your current location—the elevation angle is
needed to point the antenna. To find the elevation angle for your current
location, continue with “DISH Receiver Setup.” Even if you know the
elevation angle for your current location, you must still complete receiver
setup upon first use of the antenna.
Finding the elevation
just got easier!
Download the FREE
Winegard Mobile
App compatible with
your smartphone
For additional help determining the elevation angle for your current
location, refer to the elevation and coverage maps included with this unit, or
download the free Winegard Mobile App compatible with your smartphone.
If using the provided maps or smartphone app to determine your elevation
angle, you must still complete receiver setup. However, on step 10 of “DISH
Receiver Setup,” you do not need to enter the zip code or dish system.
If it warns that fewer satellites were
detected, select “Save.”
Then, select “Save” again.
This should clear out any previously
installed devices. Select “Done” to
return to the Point Dish Menu.
Receiver setup instructions are accurate at time of printing and may change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Input the zip code of your current location. (If using a 311 or previous model
receiver, select “Peak Angles” to enter your satellite and zip code.)
10
Searching for Satellites
2. Select “Dish 300” for the dish system.
3. Select “21” for the transponder.
Once powered on, the antenna will begin searching for satellites. The antenna will cycle through qualifying signals
before returning to the correct satellite.
Watch the signal meter on the receiver to confirm when the appropriate satellite is found; the signal bar should be
green and indicate “LOCKED” on the desired satellite. Upon finding a satellite, the unit will make adjustments to fine-
tune the signal.
4. Select the satellite that you want to point at. The 72° satellite is recommended
as a single satellite solution for DISH HD programming. See “Compatible
Satellites” for help.
If pointed at the desired satellite, make sure the unit has finished fine-tuning
the signal, and disconnect the power from the power source. Once power
has been removed, do not move the satellite dish, or the signal may be lost.
When fine-tuning, the
antenna will make slow
movements back and forth.
With all information entered, an elevation angle* should be displayed. You will need this angle to set the elevation.
NOTE
*Elevation angles may not be displayed for satellites 72° and 129°. In this case, refer to the provided elevation and coverage maps for an elevation angle.
If not pointed at the correct satellite, the Anser antenna will move to the next
strongest satellite after 45 seconds of inactivity. If the Anser antenna cycles
through all satellites but the desired satellite has not been found, disconnect
the power from the power source, set the elevation for 2–3 degrees higher or
lower, and connect the power to the power source again.
If the power is not
disconnected from the
source quickly enough, the antenna
will cycle to other satellites.
NOTE
Setting the Elevation
Align the antenna so that the cable connections are pointing approximately North.
If a first search does not
successfully find the
desired satellite, simply adjust the
elevation for another search. See
“Searching for Satellites.”
Minimum signal strength should be at least 15–20. If signal is inadequate, an elevation adjustment may be necessary.
When adjusting the elevation, the azimuth will also be adjusted. To compensate for the azimuth adjustment, either
complete a new search or (manually) slightly rotate the unit.
TIP
Turn the rotating housing until the elevation mark aligns with the elevation
angle given by the receiver or provided elevation maps. If the unit is not level,
the elevation may be slightly off.
After setting the elevation, tighten the elevation lock until fingertight. Do
not overtighten.
DISH Receiver Setup
After the unit has locked onto the desired satellite and the power has been disconnected, complete receiver setup below.
Hooking up the Antenna
11
12
13
Connect a coaxial cable from the
main port of the base to the “Sat In”
port on the back of the receiver that
will be used most often. The main
port should always be connected
when the Anser antenna is in use.
If applicable, remove the cap
Plug one end of the power cable into
the quick disconnect socket. The
cable should click into place. Then,
plug the other end into a 12 V outlet
or into a 110 V to 12 VDC converter,
such as Winegard Model GM-1200
power converter (sold separately).
from the secondary port, and run
a second coaxial cable from the
secondary port on the base to the
“Sat In” port on a second receiver
(or second input on dual tuner).
Select “Check Switch.”
Select “Test.”
The receiver will go through a
number of steps to detect your
satellite settings.
14
15
16
Coax cable connected to main port
Coax cable connected to sec. port
Power cable connected to quick
disconnect socket
Run the coaxial cable directly from the satellite receiver to the Anser
antenna when searching for signal.
The 12 VDC power source
or 110 V to 12 VDC
converter must meet power supply
specifications. See “Parts of the
Antenna” for specifications.
TIP
TIP
NOTE
If the receiver is used for DIRECTV HD programming, check that the
B-Band converter has been removed prior to connecting the antenna.
Press “Cancel” to exit the Point
Dish menu.
The receiver will acquire signal.
A program guide may download.
You are now ready to watch TV!
Download from Www.Somanuals.com. All Manuals Search And Download.
Transporting the Antenna
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY
(2 YEARS PARTS; 1 YEAR LABOR)
When transporting the antenna, return the unit to the stowed position. The elevation arrow should align with “STOW.”
Once in the stowed position, tighten the lock until fingertight.
Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date
of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized
Winegard dealer to repair or replace defective products. No warranty claim will be honored unless at the time the claim is made,
Customer presents proof of purchase to an authorized Winegard dealer (to locate the nearest authorized Winegard dealer, contact
must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty. If the date of
purchase cannot be verified, the warranty period shall be considered to begin thirty (30) days after the date of manufacture.
If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service.
Customer must provide proof of purchase to verify the product is under warranty. If the product is brought to an authorized Winegard
dealer for service prior to expiration of year one (1) of the warranty period and a defect in material or workmanship is verified by
Winegard Technical Services, Winegard Company will cover the Winegard dealer’s labor charges for warranty service. The Winegard
dealer must contact Winegard Technical Services in advance for pre-approval of the service. Approval of the service is at the sole
discretion of Winegard Company.
Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3111 Kirkwood Street, Burlington,
Iowa 52601, Telephone 800-788-4417). Customer must return the product along with a brief description of the problem and provide
Winegard Technical Services with Customer’s name, address, and phone number. Customer must also provide proof of purchase to verify
the product is under warranty. If the product is returned before the expiration of the warranty period, Winegard Company will (at its
option) either repair or replace the product.
This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper installation,
misuse, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard in any manner
whatsoever, removing or defacing any serial number, usage not in accordance with product instructions or acts of nature such as
damage caused by wind, lightning, ice or corrosive environments such as salt spray and acid rain. This Limited Warranty also does not
apply if the product becomes unable to perform its' intended function in any way as a result of the television signal provider making any
changes in technology or service.
Using Outside Receptacle
RETURN AUTHORIZATION POLICY
If your outside TV receptacle is wired for satellite, you’ll need to locate where
that receptacle leads, and connect that directly to your satellite receiver.
If the outside TV receptacle is wired for cable, the wiring will have to be
modified for use with satellite. The coaxial cable cannot run through any
other devices or switches BEFORE the satellite receiver.
A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard Warranty Services
under this warranty policy. Please call our Technical Services Department at 800-788-4417 or send an email to warranty@winegard.
com to obtain the RMA number. Please furnish the date of purchase when requesting an RMA number. Enclose the product in a prepaid
package and write the RMA number in large, clear letters on the outside of the package. To avoid confusion or misunderstanding, a
shipment(s) without an RMA number(s) or an unauthorized return(s) will be refused and returned to Customer freight collect.
WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY
OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.
In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential damages, the
above limitations or exclusions do not apply.
Typically, if wired for cable, the wiring will either run through a Winegard
power supply or video switch. The easiest way to fix this is to disconnect the
cable from that device, use a barrel connector, and connect a new cable that
Cable
runs directly to the receiver, bypassing the power supply or video switch.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state to state.
Accessories (sold separately)
SATELLITE RECEIVER WARRANTY:
WS-MOBWARREV2
See manufacturer’s limited warranty policy.
Rev. 1/10
Printed in U.S.A. ©2012 Winegard Company Rev6 6/13 2452276
TR-1518
GM-1200
RP-GM52
Winegard, Carryout, and Anser are registered trademarks of Winegard Company. DISH and ViP are registered trademarks of DISH Network L.L.C.
Bell TV is a registered trademark of Bell Canada, Inc. DIRECTV is a registered trademark of DIRECTV, LLC.
Model TR-1518 tripod mount has
adjustable height and leveling
settings of 14.5”–22” and quickly
disassembles for compact storage.
Model GM-1200 AC/DC power
converter enables you to hook up
to a 110 V power source when a 12
V power source is unavailable.
Model RP-GM52 50’ 12 V power cord is
twice the length of the included power
cable, giving more flexibility when
hooking up to a 12 V power source.
Disclaimer: Although every effort has been made to ensure that the information in this manual is correct and complete, no company shall be held liable for any errors or
omissions in this manual. Information provided in this manual was accurate at time of printing.
Download from Www.Somanuals.com. All Manuals Search And Download.
|