OWNER’S GUIDE
Operating Instructions (GB/USA)
Instrucciones de Manejo (ESP)
Mode d’emploi (FR)
Bedienungsanweisung (GER)
Mode de Emploi (ITA)
MODELS COVERED IN THIS GUIDE:
SABER
MODEL
TYPE
POWER SOURCE
36V Battery
S28
28” Disc
S34
34” Disc
36V Battery
S34SP
34” Cylindrical Head
36V Battery
STRIDE II
MODEL
TYPE
POWER SOURCE
36V Battery
QQS28
QQS34
QQS34SP
28” Disc
34” Disc
34” Cylindrical Head
36V Battery
36V Battery
IPX4
Read these instructions before operating the machine
Antes de usar la máquina lea atentamente el libro de instrucciones
Lire attentivement le mode d’emploi avant la mise en service de la machine
Vor Inbetriebnahme der Maschine Bedienungsanweisung lesen
Leggere queste istruzioni prima di usare la macchina
REV.
Y
SABER/STRIDE II 28/34 98570 8/31/99
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
OPERATIONS
PARTS LIST
Machine Data Log . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Technical Specifications . . . . . . . . . . . . . . . . . . . . 5
Operation Controls . . . . . . . . . . . . . . . . . . . . . . . . 6
Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . 7
Main Frame Assembly. . . . . . . . . . . . . . . . . . . . . . 18
Brake/Squeegee Lift Assemblies. . . . . . . . . . . . . . 20
Rear Panel Mechanical . . . . . . . . . . . . . . . . . . . . . 22
Control Panel Cover . . . . . . . . . . . . . . . . . . . . . . . 24
Electrical Panel Assembly . . . . . . . . . . . . . . . . . . . 26
Recovery Tank Assembly . . . . . . . . . . . . . . . . . . . 28
Solution Tank Assembly . . . . . . . . . . . . . . . . . . . . 30
Squeegee Assembly . . . . . . . . . . . . . . . . . . . . . . . 32
Brush/Deck Lift Assembly . . . . . . . . . . . . . . . . . . . 34
Scrub Head Assembly . . . . . . . . . . . . . . . . . . . . . . 36
Cylindrical Head Assembly . . . . . . . . . . . . . . . . . . 38
MAINTENANCE
Scrub Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Scrub Deck Skirt
/Squeegee Blades . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjusting Squeegee . . . . . . . . . . . . . . . . . . . . . . . 11
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Service Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . 14
Squeege Blade/Brush Head Options. . . . . . . . . . . 15
Service Location Details . . . . . . . . . . . . . . . . . . . . 16
Hopper Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 40
Automatic Squeegee Lift . . . . . . . . . . . . . . . . . . . . 42
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
SABER/STRIDE II 28/34 98570 10/08/98
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
The following symbols are used throughout this guide as
indicated in their descriptions:
WHEN SERVICING MACHINE:
•
Avoid moving parts. Do not wear loose clothing; jack-
ets, shirts, or sleeves when working on the machine.
Block machine tires before jacking machine up.
Use hoist or jack of adequate capacity to lift machine.
Disconnect battery connections before working on
machine.
•
•
•
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal
words -WARNING and CAUTION and FOR SAFETY. The
level of hazard intensity is determined by the following
definitions:
•
•
Avoid contact with battery acid.
Use Windsor supplied replacement parts.
! WARNING
! CAUTION
WARNING - Hazards or unsafe practices which COULD
This machine is not suitable for picking up health en-
dangering or hazardous dust.
result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result
in minor personal injury or product or property damage.
! WARNING
This appliance has been designed for use with the
brushes specified by the manufacturer. The fitting of
other brushes may affect its safety.
FOR SAFETY: To Identify actions which must be
followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do
not use the machine if it is not in proper operating condition.
Following is information that signals some potentially
dangerous conditions to the operator or the equipment. Read
this information carefully. Know when these conditions can
exist. Locate all safety devices on the machine. Please take
the necessary steps to train the machine operating personnel.
! WARNING
Batteries emit hydrogen gas. Explosion or fire can
result. Keep sparks and open flame away. Keep cov-
ers open when charging.
! WARNING
For SAFETY:
Flammable Materials Or Reactive Metals Can Cause
explosion or fire. Do Not Pick Up These Materials.
DO NOT OPERATE MACHINE:
•
•
•
•
•
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
Before use all covers and doors shall be put in the
! WARNING
Hazardous Voltage. Shock can result. Disconnect
batteries before working on machine. Only qualified
personnel should work inside machine.
positions specified on the instructions
WHEN USING MACHINE:
•
•
•
Use caution when backing machine.
Do not carry riders on the machine.
During operation attention shall be paid to other per-
sons, especially children.
Always follow basic safety and traffic rules.
Go slow on slippery surfaces and grades.
! WARNING
Machine can emit excessive noise. Consult with
your regulatory agency for exposure limits. Hearing
loss can result. Wear hearing protection.
•
•
•
When leaving unattended, secure against uninten-
tional movement.
BEFORE LEAVING OR SERVICING MACHINE:
•
•
•
•
Stop on a level surface.
Set the parking brake.
Turn off the machine.
Remove key from switch.
SABER/STRIDE II 28/34 98570 7/14/98
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
MODEL:SABER/STRIDE II 28/34
Year of Construction: 1998
Solution Tank:
33 gal.
Recovery Tank:
Electrical System:
Tires:
33 gal.
Nominal Power:
Mass:
2.88 kW
850kg
36 volt, 6 x 6 volt 250-350 A/H
12” pneumatic
Rated Voltage:
Rated Amperage:
Cleaning Path:
36VDC
80 amps
Dimensions: (LxWxH) 69” x 36” x 45”
Special NOTES:
28” (2 x 14”) S28, QQS28
34” (2 x 17”) S34, QQS34
34” (CYL) S34SP, QQS34SP
The sound pressure level at the operator’s ear was measured
to be 74 dBA. This was a nearfield, broad-band measurement
taken in a typical industrial environment on a tile floor. This
appliance contains no possible source of impact noise. The
instaneous sound pressure level is below 63 Pa.
Drive Motor:
.5 hp
Brush Motor:
.75 hp
The weighted root mean square acceleration at the operator’s
arms was measured to be below 2.5 m/s. This was a tri-axial,
third-octive-band measurement made during normal operation
on a composite tile floor. The measurement and related calcu-
lations were made in accordance with ANSI S3.34-1986.
Brush Pressure:
Brush Speed:
Solution Control:
0-200 lbs.
200 rpm
Gravity feed, fully variable with
automatic shut-off in neutral.
View: Side view of machine
45”
69”
SABER/STRIDE II 28/34 98570 5/1/98
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION CONTROLS
1. Squeegee /Vacuum Switches. Turns on and off the vacuum and squeegee system seperately if desired.
2. Brush Pressure Indicator/Switch.Sets brush pressure on floor with LED’s to show pressure level.
3. One Touch Switch. Activates scrubbing and vacuuming functions. Pressing once turns “ON”. Pressing twice turns “OFF” scrubbing
and vacuuming functions.
4. Key Switch. Turns ON and OFF the machine.
5. Emergency Stop Switch. Cuts off power to the machine.
6. Speed Control Lever. Controls the machines overall speed.
7. Direction Control Lever. Simply push the lever forward or pull the lever toward you to move the machine in the direction you choose.
8. Height Adjustment Handle. Adjusts the height of the handle and rear panel.
9. Solution Control Lever. Pulling lever up turns solution flow off to scrub deck. Pushing down increases solution flow to scrub deck.
10. Traction Motor Circuit Breaker. 25 Amp. Protects the traction drive electrical system.
11. Vac Motor Circuit Breaker.25 Amp. Protects vac motor from damage.
12. Brush Motor Circuit Breaker (Right brush). 30 Amp. Protects brush motor system.
13. Brush Motor Circuit Breaker (Left brush). 30 Amp. Protects brush motor system.
14. Actuator Motor Circuit Breaker. 3 Amp. Protects actuator lifting system.
15. Squeegee Lift Lever.Raises and lowers the squeegee.
16. Recovery Tank Full Indicator.
17. Recovery Tank Drain Hose.
18. Brush Circuit Breaker Indicator.
19. Solution Tank Drain Hose.
20. Hour Meter.Tracks operating hours and is helpful for scheduling service.
21. Battery Charge Level Indicator. Displays the existing power level of the battery.
DETAIL: Touch pad control panel
16
18
2
21
20
5
VIEW: Rear view of machine
100 hr
7
12
13
9
3
1
4
6
14
15
8
17
10
19
11
SABER/STRIDE II 28/34 98570 5/1/98
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE OPERATION
STARTING MACHINE
SCRUBBING WITH THE SABER/STRIDE II
NOTE: Perform pre-run machine check before operating
machine.
Plan the scrubbing pattern in advance. The longest track is
around the perimeter of the area to be cleaned. For efficient
operation, the runs should be the longest possible without
turning, stopping, or raising and lowering scrub deck/
squeegee.
FOR SAFETY: Before starting machine, make sure that
all safety devices are in place and operating properly.
1. Turn the key switch clockwise to the “ON” position.
Move the directional control lever in the desired
direction.
NOTE: In order to achieve the best possible results, the
area which is to be cleaned should be swept before scrub-
bing. Large debris, strings, wire must be removed to pre-
vent being caught in brushes or squeegee.
FILLING THE SABER/STRIDE II
FOR SAFETY: Before leaving or servicing machine;
stop on level surface, set parking brake, turn off ma-
chine and remove key.
BEGIN SCRUBBING
1.
2.
3.
Set the parking brake, and turn “OFF” key switch.
1.
2.
Turn key switch to “ON” and release the brake.
Remove solution tank cover.
Travel to the start of the scrub pattern. Press
the brush button number 1 on the console touch
pad to start the vacuum, brush motors, and lower
scrub deck and manually lower squeegee to the
floor.
Fill the solution tank with clean water, leaving enough
room for the required amount of cleaning solution.
The solution tank capacity is 33 gallons (124.9 liters).
The water must not be hotter than 140°F (60°C)to
prevent damage to the tank.
3.
4.
Press the scrub pressure button to the desired
scrubbing pressure.
4.
Measure the chemical into the solution tank. Liquid
chemicals should be added to the solution tank after
filling with water. Dry chemicals should be thoroughly
mixed before being added into solution tank.
Commercially available, high alkaline floor cleaners
are suitable for use in the SABER/STRIDE II
solution system.
Finally adjust the solution flow using lever to the left
of the control panel.
STOP SCRUBBING
1.
Raise the scrub head, again using button number
NOTE: Read the chemical manufactures recommended
proportion instructions.
1. Allow directions lever to return to neutral
position after squeegee has passed beyond the
position where the scrub deck was raised.
Vacuum motor will cut off after an additional 14
second delay in order to clear the recovery system
of solution.
5.
6.
Fill the solution 5” from the bottom of the fill inlet.
Replace solution tank cover.
2.
3.
Turn the key switch "OFF” and set the parking
brake.
! WARNING
Flammable materials can cause an explosion or fire.
Do not use flammable materials in the tanks
Pull back solution knob to full off position if
scrubbing operation is complete.
SABER/STRIDE II 28/34 98570 5/1/98
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE OPERATION
DOUBLE SCRUB
Floors which are heavily soiled or have thick accumulations
of floor finish may not clean sufficiently with one pass. In
these cases it will be necessary to double scrub.
To double scrub, begin scrubbing as usual, but after push-
ing number 1, press the squeegee button to turn off vac mo-
tor. Manually raise the squeegee. Make the first pass over
the surface being cleaned with the solution on, and brush-
es down and squeegee up. This allows the solution to stay
in contact with the soil while loosening the surface accumu-
lation with the brushes. Allow time for the first application
to stay in contact with floor. Length of time between the first
and second pass depends on amount of accumulation and
the type of chemical being used. A second scrubbing with
the squeegee down and again the solution and brushes on
will further loosen soil. The additional application of solu-
tion will further assist the difficult cleaning job.
EMPTYING AND CLEANING TANKS
RECOVERY TANK
SOLUTION TANK
1. Park the SABER/STRIDE II next to a floor drain.
1. Drain solution tank by unhooking the small solution
Drain hose is on left rear corner of machine.
drain hose from left rear of tank.
2. Turn “OFF” the key switch and set the machine
2. Loosen T-handle on plug enough to remove plug.
parking brake.
Allow tank to drain completely.
3. Unhook the large drain hose from the retainer and
unscrew T-handle on plug enough to release the plug,
then lower hose in direction of the drain. Recovered
solution will come out with some force.
3. Flush tank of all chemical solution.
4. Run several gallons of clean water through system.
NOTE: Never allow solution to remain in tank. Damage to
tank, seals and valves could occur.
4. The recovery tank should then be flushed out with
clean water. Hinge solution tank open to access
recovery tank.
5. If machine is to be stored, leave solution tank hinged
open.
SABER/STRIDE II 28/34 98570 7/14/98
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SCRUB BRUSHES
NOTE: All original equipment brushes are equipped with
“Perform Alert©. This feature will tell the operator when it
is time to replace the scrub brushes. “Perform Alert©
brushes have bright yellow tufts located on these tufts
are pre-trimmed to indicate the length of a worn out
brush. When the tufts in the scrub brush wear to a length
equal to the yellow tufts, the scrub brushes should be re-
placed.
The scrub brushes should be checked before each days
work for wire, string, wear, or damage. The scrub brush-
es should be replaced if brush bristles are missing or if
yellow Perform Alert© indicate minimum brush length.
NOTE: For uniform scrubbing, scrub brushes must be re-
placed as a set.
There are five different types of brushes available to cov-
er applications from cleaning heavily soiled floors to pol-
ishing. A pad driver is also available to take advantage
of the many cleaning pads on the market and further add
to the flexibility of the SABER/STRIDE II. Please refer to
the following to assist in selecting the proper brush or pad
for the work at hand.
REPLACING OR INSTALLING SCRUB BRUSHES
1. With the scrub deck up, turn “OFF” the machine
and set the parking brake.
FOR SAFETY: Before leaving or servicing machine;
Stop on level surface, set parking brake, turn off
machine and remove key.
UNCOATED FLOORS
Aggressive Grit is a nylon fiber impregnated with sili-
cone carbide grit. It grinds away stain, soil, and removes
surface material
2. Locate release lever on top of brush or pad driver.
Rotate release lever counter-clockwise and the
brush/pad driver will release and drop down.
Mild Grit is a less aggressive silicone carbide grit suit-
able for cleaning medium soil conditions. Advantages
are faster ground speed than nylon bristles on light solid
applications.
3. To reinstall, center the brush driver under the brush
drive hub. Raise until it contacts brush driver
assembly. Turn clockwise until release lever plate
locks into position.
Nylon is a general purpose scrub brush with stiff bristles.
Polypropylene works well for maintaining concrete,
wood, and tile floors.
NOTE: Check that release plate is completely closed
and pad / brush is securely attached. Damage to driver
or brush could occur.
FINISHED FLOORS
Nylon Polish is the softest brush. It will gently clean fin-
ished tile or terrazzo floors without removing floor finish
or floor material. Used for washing highly polished or
burnished floors.
4. Repeat the procedure for the opposite side of the
machine.
Nylon bristles are used in a variety of applications on
coated or uncoated surfaces.
White Pads (Polishing) are used for dry polishing to
achieve a high-gloss appearance, or surface washing on
highly polished or burnished floors
Red Pads (Buffing) are used for light-duty scrubbing.
When used with a mild detergent they will provide surface
cleaning without removing the finish.
Blue Pads (Scrubbing) are used for heavy-duty scrub-
bing, and light stripping. The blue pads remove less fin-
ish than brown stripping pads, yet will remove black
marks, stains, and dirt.
Brown Pads (Stripping) are used for easy and complete
removal of old floor waxes/finishes. They will quickly re-
move ground in dirt, black heel marks, and spills When
used with the proper stripper, this pad leaves the floor
clean and ready for finishing.
SABER/STRIDE II 28/34 98570 7/14/98
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SCRUB DECK SKIRT AND SQUEEGEE
TO REPLACE OR ROTATE REAR SQUEEGEE
BLADES
The skirts and squeegee should be inspected for wear
and damage. The skirt is self adjusting. Replace skirt
when they become cracked, worn, torn or brittle.
1. With the squeegee in the up position, turn the key
switch “OFF”.
SQUEEGEE BLADES
2. Remove the squeegee from the machine. Unlatch
and remove blade retainer strap and remove
squeegee blade assembly.
NOTE: See page 15 of this guide for a complete table on
squeegee options.
The front squeegee blade allows solution to pass through
channels in the blade into the squeegee tool while main-
taining vacuum to provide lift. The front blade has four
wear surfaces and can be rotated for extended life.
There are three different notch patterns and three differ-
ent colors of squeegees for varying floor conditions. The
red squeegee is used for normal, smooth surfaces. The
blue squeegee is used for tiled surfaces. The green
squeegee is used for rough surfaces. The linatex squee-
gees are used for industrial settings. The front blade
should not require regular replacement under normal
use.
FOR SAFETY: Before leaving or servicing machine;
Stop on level surface, set parking brake, turn off
machine and remove key.
3. Rotate the squeegee to new edge position or
replace as required. Each blade has four new edge
positions.
The rear blade wipes the floor to a near dry condition. It
is important the rear blade be in good condition to prop-
erly do its job. The rear squeegee blades come in an as-
sembly with three different options. Each squeegee
blade assembly has four wear surfaces for extended ser-
vice.
Check both the front and rear squeegee blades for dam-
age, wear, and adjustment each day in the pre-run check.
Change the front blade if it is torn or has an uneven edge.
Change the rear blade if it is less than 1/2 the original
thickness.
SQUEEGEE DEFLECTION
CORRECT
NOT ENOUGH
TOO MUCH
SQUEEGEE SIDE VIEW OF BLADES
SABER/STRIDE II 28/34 98570 7/14/98
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ADJUSTING SQUEEGEE
Adjusting the squeegee is a two part process. First, the
squeegee tool must have correct pitch in order for the
squeegee blade to have the same deflection at each tip
as well as the center.
The pitch adjustment on the SABER/STRIDE II
is facilitated by the use of a spirit level mounted on the
squeegee tool. The second adjustment is the amount of
deflection or down pressure on the squeegee. The ideal
deflection is conveniently marked by colors on the squee-
gee tool according to the type of floor and squeegee
blade employed.
3/8”
TO ADJUST SQUEEGEE PITCH
PROPER DEFLECTION OF SQUEEGEE BLADE
1. Choose a smooth, level surface. Turn “ON” the key
switch, release the machine parking brake. Lower
the squeegee and drive forward at least 2 feet (60
cm).
2. With the squeegee down, stop the machine with the
brake and set the parking brakes. Do not allow the
machine to roll back.
FOR SAFETY: Before leaving or servicing machine;
Stop on level surface, set parking brake, turn off
machine and remove key.
3. Determine the differences, if any, in deflection of the
squeegee blade between each end and the middle.
Proper adjustment is obtained when deflection is
equal all the way across tool. This should
correspond to the bubble being in the middle position
of the spirit level.
4. To decrease the deflection of the squeegee blade at
the ends, loosen plastic knobs near the squeegee
center. To increase the deflection at the ends of the
squeegee assembly, tighten plastic knobs on trailing
arm.
5. Again check the deflection of the squeegee blades.
Repeat steps 1 through 4 until the deflection is equal
across the entire rear squeegee blade.
TO ADJUST AMOUNT OF REAR SQUEEGEE
DEFLECTION
FOR SAFETY: Before leaving or servicing machine;
Stop on level surface, set parking brake, turn off ma-
chine and remove key.
1. Choose a smooth, level surface. Lower the
squeegee and drive forward at least 2 feet.
2. With the squeegee down, stop the machine with
the brake and set the parking brakes. Do not allow
the machine to roll back.
3. Observe the amount of squeegee deflection. It
should deflect 3/8 in (9.5 mm) across the entire
width of the squeegee.
4. To adjust the squeegee deflection, loosen knob on
the squeegee slide bar.
5. Slide bar to left to increase deflection. Sliding bar to
right decreases deflection
6. Turn on the key switch, release the machine parking
brake. Raise, then lower squeegee assembly.
Drive forward at least 2 feet.
7. Repeat steps 2 through 4 until deflection of 3/8 in.
(9.5 mm) is reached.
TIRES AND WHEELS
Check for low or worn tires. Fill to proper pressure as
needed (50 psi front).
Check wheel nuts for tightness, tighten as necessary to
80 foot pounds.
SABER/STRIDE II 28/34 98570 7/14/98
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERIES
The batteries provide the power to operate the machine.
The standard are four 6 volt batteries rated at 250 A/h at
a 6-hour rate. The batteries require regular maintenance
to keep them operating at peak efficiency.
3. Do not add water until the battery is fully charged.
4. Wipe off the top of the batteries at least once a
week.
5. Test battery condition with a hydrometer at least
once a week.
The machine batteries will hold their charge for long peri-
ods of time, but they can only be charged a certain num-
ber of times. To get the greatest life from the batteries,
charge them when their charge level reaches 25% of a
full charge. Use a hydrometer to check the charge level.
6. Ensure that all connections are tight and all
corrosion removed.
7. Every 4 to 6 months, remove the batteries from the
machine and clean the battery cases and battery
compartment.
Do not allow the batteries to remain in a discharged con-
dition for any length of time. Never expose a discharged
battery to temperatures below freezing. Discharged bat-
teries will freeze causing cracked cases. Do not operate
the machine if the batteries are in poor condition or if they
have a charge level below 25% (specific gravity below
1.155).
CHECKING BATTERY SPECIFIC GRAVITY
Use a hydrometer to check the battery specific gravity.
A
Keep all metallic objects off the top of the batteries, as
they may cause a short circuit. Replace worn or dam-
aged cables and terminals.
Check the electrolyte level in each battery cell before and
after charging the batteries. Never add acid to the batter-
ies, use water. Do not allow water level to fall below the
battery plates. Portions of plates exposed to air will be
destroyed. Do not overfill. Keep plugs firmly in place at
all times.
B
Battery Check
CHECKING GRAVITY
A. Hydrometer
B. Battery
! CAUTION
When servicing machine, avoid contact with
battery acid.
! WARNING
NOTE: Do not take readings immediately after adding
water, if the water and acid are not thoroughly mixed, the
reading may not be accurate.
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
Check the hydrometer readings against this chart
! WARNING
SPECIFIC GRAVITY @80° F(27° C)
BATTERY CONDITION
Wear eye protection and protective clothing
when working with batteries.
1.265
1.225
1.190
1.155
1.120
100% charged
75% charged
50% charged
25% charged
Discharged
! WARNING
Charge batteries in a well ventilated area.
BATTERY MAINTENANCE
NOTE: If the readings are taken when the battery elec-
trolyte is any temperature other than 80 °F(27° C), the
reading must be temperature corrected.
1. When cleaning the batteries, use a solution of
baking soda and water. Do not allow the cleaning
fluid to enter the battery cells. Electrolyte will be
neutralized.
2. Maintain the proper electrolyte level in each battery
cell. If a cell should accidentally overflow, clean
immediately.
To find the corrected specific gravity reading when the temper-
ature of the battery electrolyte is other than 80° F(27° C):
Add(+) to the specific gravity reading 0.004(4 points), for each
10 F(6° C) above 80 F(27° C).
Subtract(-) from the specific reading 0.004(4 points), for each
10° F(6° C) below 80° F(27° C).
SABER/STRIDE II 28/34 98570 7/14/98
12
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERIES
TO CHARGE THE BATTERIES
7. Plug the charger connector into the battery connector.
Connect the charger AC plug to a wall outlet. The
charger gauge should indicate that the batteries are
charging.
8. When the batteries are fully charged, disconnect the
charger from the AC wall outlet, then disconnect the
charger from the batteries.
9. Connect the batteries to the machine connector.
10. Check the electrolyte level. It should be up to the indi-
cator ring. If necessary add distilled water.
11. Lower the solution tank.
! CAUTION
When servicing machine, avoid contact with bat-
tery acid.
! WARNING
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
! WARNING
CHANGING BATTERIES
TO REMOVE BATTERIES
Stop the machine in a clean area next to the charger
Turn off machine and set parking brake.
Wear eye protection and protective clothing when
working with batteries.
! WARNING
FOR SAFETY: Before leaving or servicing machine;
Stop on level surface, set parking brake, turn off ma-
chine and remove key
Charge batteries in a well ventilated area. Leave
the solution tank open.
Use a 36 volt, 20 amp maximum output, DC charger which
will automatically shut off when the batteries are fully
charged to charge the six battery pack.
1. Raise the solution tank.
2. Engage solution tank support arm
3. Disconnect battery pack from machine.
4. Use the proper size open end wrench to disconnect
main ground wire first and secure cable terminal away
from batteries.
5. Disconnect main positive lead and secure cable termi-
nal away from batteries.
1. Stop the machine in a clean, well ventilated area next
to the charger
2. Turn “OFF” machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine;
Stop on level surface, set parking brake, turn off
machine and remove key
6. Loosen both terminals on each jumper cable and
remove one at a time.
7. Prepare a suitable site to place the batteries.
8. Attach suitable battery lifting device and lift batteries
from the machine.
3. Drain solution tank and raise the solution tank and
lock the support arm. Make sure the support arm is
fully engaged.
! WARNING
Batteries are a potential environmental hazard.
Consult your battery supplier for safe disposal
methods.
! WARNING
Batteries emit hydrogen gas. Explosion or fire can re-
sult. Keep sparks and open flame away. Keep covers
open when charging.
BATTERY CONNECTIONS SABER/STRIDE II
4. Check the electrolyte level in each battery cell. Before
charging, add just enough water to cover the plates.
After charging is complete, add just enough water to
bring up the level to the indicator ring. If the water level
is too high before charging, normal expansion of the
electrolyte may cause an overflow, resulting in loss of
battery acid balance and damage to the machine.
5. Replace the battery caps, and leave them in place
while charging.
+
blk
red
+
red
blk
+
blk
blk
red
+
6. Unplug the battery connector from the machine.
red
blk
blk
+
FOR SAFETY: When charging, connect the charger to
the batteries before connecting the charger to the AC
wall outlet. Never connect the charger to the AC wall
outlet first. Hazardous sparks may result.
+
red
+
red
SABER/STRIDE II 28/34 98570 7/14/98
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE SCHEDULE
Before
Starting
Maintenance Item
Daily
Weekly Monthly Annually
Check Battery water level
*
*
*
*
*
the Work
Period
Check Vac Hose Connections
Clean the Squeegee Blades
Inspect Brushes or Pads for debris ie: wire, string, wear
Inspect Vac fan shut off float screen
End of Work
Period
Before
Drain & Rinse Tanks
*
*
*
*
*
*
*
*
Raise Squeegee Assembly
Raise Scrub Deck Assembly
Charge the Batteries
Storing
Remove the Pad Drivers/Brushes
Check the Brushes/Padsfor Damage and or wear
Clean Squeegee blades
Clean recovery tank vac shutoff & screen
Check Battery Cells w/Hydrometer
Check Solution Strainer
*
*
*
*
Check Pivot Points, Caster, and Squeegee for proper lubrication
Inspect tank and hoses
Clean tops of Batteries and Tray
*
*
*
*
Check Battery Cable Clamps
Use a Vacuum to remove lint from the motor windings
Grease Squeegee pivot and Casters
Inspect all Motors for Carbon Motor Brush Wear.
*
SABER/STRIDE II 28/34 98570 5/1/98
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SQUEEGEE BLADE/BRUSH HEAD OPTIONS
SQUEEGEE BLADE OPTIONS
S28 /
QQS28
S34 /
QQS34
S34SP /
QQS34SP
P/N
Desc.
Color
OPTION
73932
73934
82529
82528
82638
82637
82641
82640
73935
73900
73902
73901
73936
73937
73925
73922
73926
73923
73927
73924
FRONT, STANDARD
REAR, STANDARD
REAR, LINATEX
RED
RED
X
X
X
X
X
X
X
X
X
standard
standard
option
option
option
option
option
option
standard
option
option
option
standard
standard
option
option
option
option
option
RED/NOTCH
RED/NOTCH
BLUE
FRONT, LINATEX
X
X
REAR, (FOR TILE)
FRONT, (FOR TILE)
REAR, (FOR BUTTONS)
FRONT, (FOR BUTTONS)
REAR, STANDARD
REAR, LINATEX
BLUE
GREEN
GREEN
RED
X
X
X
X
X
RED/NOTCH
BLUE
REAR, (FOR TILE)
REAR, (FOR BUTTONS)
REAR, STANDARD
FRONT, STANDARD
REAR, LINATEX
GREEN
RED
X
X
X
X
X
X
X
X
RED
RED/NOTCH
RED/NOTCH
BLUE
FRONT, LINATEX
REAR, (FOR TILE)
FRONT, (FOR TILE)
REAR, (FOR BUTTONS)
FRONT, (FOR BUTTONS)
BLUE
GREEN
GREEN
option
BRUSH HEAD OPTIONS
Nylon
Mild
Aggressive
Pad
Driver
Poly
Brush
Model
Required
Brush
82194
Grit
Grit
SABER / STRIDEII 34 SCRUB
PLUS (CYLINDRICAL)
2
82193
82196
82197
-
SABER / STRIDE II 28
SABER / STRIDE II 34
2
2
02337
02338
02344
02347
02345
02348
02346
02350
n/a
n/a
SABER/STRIDE II 28/34 98570 9/15/98
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE LOCATION DETAILS
BRUSH HEAD MODELS: S28, S34, QQS28, QQS34
ALL MODELS
1
2
SQUEEGEE ASSEMBLY
3
4
REAR ELECTRICAL
CONTROL PANEL
(REF. )
6
5
BRUSH HEAD
CYLINDRICAL HEAD MODELS: S34SP, QQS34SP
2
SQUEEGEE ASSEMBLY
3
4
7
2
CYLINDRICAL HEAD
(OPTION)
SABER/STRIDE II 28/34 98570 5/1/98
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE LOCATION PARTS LIST
Serial No.
Notes:
Ref
Part No. Qty Description
From
To
1
2
3
4
5
6
7
70532
80657
87029
48012
82191
27756
27770
6
1
2
2
1
1
1
SCR, 10-32 X 1/2 PPHMS BLK
PIN, COTTER HAIR .148" DIA X 3/4
WASHER, 5/16 FLAT SS
KNOB, 5/16-18 4 PRONG
PIN, COTTER HAIR .178" DIA X 1"
COVER, FRONT
QTY 2 SEE NOTE *
MODELS: S28,S34,QQS28, QQS34
COVER, FRONT 34 CYL
* NOTE: QUANTITY USED FOR S34SP MODEL ONLY
SABER/STRIDE II 28/34 98570 7/9/98
33
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|