PROPANE POWERED HIGH SPEED
BURNISHER/STRIPPER
Operating Instructions
MODELS: L21H13
L24H13
10023000 LS30H13 10023110 L21K13 10023010
10023040 L21K17 10023020 L24K17 10023060
10023080 L24ER22 10023030 L27K17 10023090
L27H13
LS30H13 10023110 L27ER22 10023070
Read these instructions before using the machine
C
86039180 05/23/07
PRV NO. 98996
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Machine Data Log/Overview.........................2
Table of Contents..........................................3
GROUP PARTS LIST
21” Deck Group. ...........................................5-1
24” Deck Group. ...........................................5-3
27” Deck Group. ...........................................5-5
30” Stripper Group........................................5-7
Kawasaki Fuel Block.....................................5-9
Kawasaki Wiring. ........................................ 5-10
Kawasaki Fuel System. .............................. 5-11
Honda Fuel System. ................................... 5-12
Kill Switch ................................................... 5-13
Clutch and Switch....................................... 5-14
Belt Chart/Notes ......................................... 5-15
Warranty. .................................................... 5-16
HOW TO USE THIS MANUAL
How to use this Manual.................................1-1
SAFETY
Important Safety Instructions ........................2-1
Hazard Intensity Level. .................................2-2
OPERATIONS
Machine Operation........................................3-1
Before Operating the Machine...................3-1
Emergency Stopping Procedure................3-2
Transporting/Storing Machine....................3-2
Propane Fuel System. ...............................3-3
Changing oil...............................................3-3
Adjusting Belt Tension. ..............................3-3
Refueling/Storing Cylinders. ......................3-3
MAINTENANCE
Service Schedule..........................................4-1
Installing or Removing Pad...........................4-2
Installing or Removing Pad Driver ................4-2
Machine Troubleshooting..............................4-3
3
LIGHTNING 86039180 05/23/07
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THIS MANUAL
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards is identified that could
result in product or personal injury, or severe injury
resulting in death.
This manual contains the following sections:
-
-
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
-
-
MAINTENANCE
PARTS LIST
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition.
Parts may be ordered from authorized Windsor
dealers. When placing an order for parts, the
machine model and machine serial number are
important. Refer to the MACHINE DATA box which
is filled out during the installation of your machine.
The MACHINE DATA box is located on the inside of
the front cover of this manual.
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
MODEL _____________________________________
DATE OF PURCHASE ________________________
SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
DEALER NAME ______________________________
OPERATIONS GUIDE NUMBER __________________
-
-
PRV NO. – reference number.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
SERIAL NO. FROM – column indicates
the first machine the part number is
applicable to. When the machine design
has changed, this column will indicate
serial number of applicable machine.
The main illustration shows the most
current design of the machine. The
boxed illustrations show older designs. If
column has an asterisk (*), call
-
-
PUBLISHED ________________________________
Copyright 2002 Windsor Industries, Printed in USA
The model and serial number of your machine is on
the bottom back-end of the machine.
manufacturer for serial number.
NOTES – column for information not
noted by the other columns.
-
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
LIGHTNING 86039180 05/23/07
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using a propane powered appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
WARNING:
To reduce the risk of fire, explosion, or injury:
Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer’s recommended components and
attachments.
Maintenance and repairs must be done by qualified personnel.
Only trained operators should be allowed to operate propane powered floor machines.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into
water, return it to an authorized service center.
Check fuel cylinder for overfill before taking it into the building or placing it in storage.
Install fuel cylinder in a well ventilated place.
Be aware of possible leaks of propane gas if odor is present.
If the machine is stored inside a building, remove the fuel cylinder & store properly outside.
Secure fuel cylinders when being transported. If attached to the machine service valves should be
OFF.
Never store fuel cylinders in a vehicle, building, or area where they may exposed to high temperature
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
Machine can cause a fire when operating near open flames or sparks.
This machine is suitable for commercial use, for example in hotels, schools, hospitals,
factories, shops and offices for more than normal housekeeping purposes.
Remove fuel cylinder and disengage the starter before cleaning or servicing.
Before the machine is discarded, the fuel cylinder must be removed and properly disposed of.
During operation, attention shall be paid to other persons, especially children.
Before use all covers and doors shall be put in the positions specified in the instructions.
When leaving unattended, secure against unintentional movement.
When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.
This appliance has been designed for use with the brushes specified by the manufacturer. The fitting
of other brushes may affect its safety.
SAVE THESE INSTRUCTIONS
LIGHTNING 860389180 05/23/07
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY . The level of hazard intensity is determined by the following definitions:
! WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To identify actions which must be followed for safe operation or equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate
all safety devices on the machine. Please take the necessary steps to train the machine operating
personnel.
FOR SAFETY
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use Windsor approved replacement parts.
! WARNING
Fuel cylinders emit propane gas. Explosion or fire can result. Keep sparks and open flame away.
Do not smoke around fuel cylinders.
! WARNING
Remove fuel cylinder before working on machine. Only qualified personnel should work on
machine. Always wear eye protection and protective clothing when working on machine.
LIGHTNING 860389180 05/23/07
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE OPERATIONS
Your machine is shipped ready for your operation,
with exception of fuel cylinder. For hazard and safety
issues, the cylinders are sent with no fuel. Prior to
operation have your cylinder filled at a reputable
propane dealer.
STARTING PROCEDURES
Burnisher:
1. Tilt machine back on rear casters so pad is off
the floor.
2. Slowly open the service valve on the fuel
cylinder. NOTE: opening the service valve too
quickly may cause the excess flow valve to stop
the flow of propane. If this occurs, close the
service valve, wait a few seconds and re-open it
SLOWLY!
! CAUTION
The fuel cylinder supplied with this machine is a
DOT 4E240 propane cylinder. Cylinders not branded
with DOT 4E240 on the top collar should not be
used. Never use a cylinder from a barbecue, etc. on
this machine.
3. Push the throttle lever to the choke position and
engage the starter by using the start button.
(NOTE: If equipped with key switch, start by
turning the key) Do not engage starter for more
than 20 seconds at a time, allow 10-20 seconds
between attempts to start the engine.
The capacity of the 4E240 cylinder is 20lbs., 80% of
the total water capacity. Never overfill the cylinder.
BEFORE OPERATING THE MACHINE:
1. Check fuel cylinders: Check for overfill before
taking them into the building.
To check a cylinder for overfill:
a. Take it to a safe area outside.
b. Open the fixed liquid level gauge.
(bleeder valve)
c. Observe the gas from the valve:
1. If White cloud – Overfilled
2. If Clear vapor – Safe
d. If overfilled, allow to vent until vapor is
Clear in color.
4. When engine starts, ease the throttle back to
running position.
! WARNING
DO NOT run engine with throttle in the choke
position. Excessive harmful emissions will be
produced putting you and others in harms way.
5. Increase throttle to about ¾ and carefully lower
the machine pad to the floor while walking
forward slowly.
2. Check Oil level: Check level prior to starting
engine and daily before using machine. Use
specified oil if necessary to add. DO NOT OVER
FILL OIL LEVEL, to do so may cause damage to
the engine, thus voiding warranty.
Optional: Electric Clutch
If equipped with and optional clutch, move throttle to
slow and engage the clutch by squeezing the
“trigger switch” on the operation handle. Move the
throttle to ¾ speed, slowly lower pad to the floor
while walking forward slowly.
When checking oil refer to the specific engine
manufacturers instruction manual, as some
engines differ in correct procedure.
Use 10W30 oil.
3. Check Air Filter: Be sure the carburetor air filter
is free of dust/oil, etc. NOTE: Dirty filters is the
most frequent cause of elevated toxic emissions.
Check and clean recoil dust filter if necessary.
(see specific engine owners manual)
4. Check Pad & Pad Driver.
5. Adjust handle height: Use a 9/16 wrench to
loosen and tighten pivot points. Most find it
necessary to adjust the handle to “belt height”
for optimum control.
6. Install Fuel Cylinder: Take machine to a well
ventilated area. Check cylinder for overfill. (see
step 1) Install cylinder on machine with tank
strap. Connect the fuel cylinder to the machine
using “Rego” connection. Tighten “hand-tight”.
NOTE: Careful not to cross thread the Rego
connection. Open the service valve slowly. Be
alert for propane leaks. To remove cylinder
reverse the procedure.
LIGHTNING 86039180 05/23/07
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE OPERATIONS
EMERGENCY STOPPING PROCEDURE
In case of an emergency, the machine can be
brought to an instant stop by:
STARTING PROCEDURES
Stripper:
! CAUTION
1. Pull the throttle back to stop position or turn key
switch to OFF, if equipped.
2. Close service valve on the fuel cylinder.
3. If the machine is equipped with a “Kill Switch”,
activate the switch.
This machine is only as fast as you allow it to be. It
is imperative that you keep the floor wet with
stripping solution while stripping and remove the
sludge quickly and completely. Rinsing thoroughly
before re-coating with sealer or floor finish.
! CAUTION
The engine may backfire when stopped in this
manner.
1. Clear all areas of all displays. Remove any dust
and stickers from floor.
2. Prepare stripping solution according to
STOPPING PROCEDURE
instructions on label.
1. Close the service valve on the fuel cylinder while
the engine is running. This serves to “purge” the
fuel system of all flammable gas.
2. Tilt the machine back on it’s rear caster and
allow the engine to run until it stops.
3. Apply solution to the floor using a mop or other
method of application. KEEP FLOOR WET
WITH SOLUTION.
4. Allow 10 minutes or so for solution to penetrate
floor coating.
3. Turn the key switch OFF if equipped.
5. Using a “doodle bug” scrape the edges clear of
floor finish.
Do not leave the machine unattended while the
engine is running for long periods of time. If
necessary to leave the machine for short periods to
move a display etc. move the throttle lever to idle
position and tip machine back on the rear caster.
6. Begin stripping with the machine. (one pass is
generally all that is needed).
7. Follow the machine with recovery of sludge and
It has been the accepted practice to start buffing
from the right side of the aisles. Most smaller
machines are offset to the right to allow buffing close
on that side.
damp mop. NOTE: rinse floor thoroughly.
Keep both models moving. Running the machine in
one place for more than a few seconds may damage
the floor.
TRANSPORTING/STORING MACHINE
When transporting the machine from one site to
another, secure the machine with the fuel cylinder
installed and the service valve OFF. Allow the
engine to cool down some before loading the
machine for transport.
! WARNING
Exhaust emissions contain harmful toxic gases. The
worst being carbon monoxide. Do not operate the
machine in confined areas for prolonged times.
Always make certain that adequate ventilation is
had.
When storing the machine, remove the propane
cylinder and store outside. (see pg. 3-3 for Storage
of Fuel Cylinders) Perform all daily maintenance
procedures. Store machine in a cool, dry, secure
area where it will not be damaged by other traffic.
Tilt the machine back on the rear caster with the pad
off of the floor.
! CAUTION
Never engage clutch in the fast run position or with
the pad on the floor, this may cause damage to the
clutch and the floor.
! WARNING
Be careful not to allow the machine to come in
contact with loose tiles or other obstruction on the
floor. The pad is turning at approximately 2000
RPM. If loose objects are hit by revolving pad they
could become dangerous missiles.
LIGHTNING 86039180 05/23/07
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE OPERATIONS
PROPANE FUEL SYSTEM
REFUELING/STORING CYLINDERS
The following information refers to regulations within
the United States of America and Canada. For other
countries, the owner must assure that the required
regulations are met.
! WARNING
Adjustments and repairs to the propane fuel system
can only be made by properly trained and certified
Service Technicians.
National Fire Protection Association (NFPA) has
established standards for the storage and handling
of liquefied petroleum gasses. This standard is
NFPA 58.
! WARNING
Improper adjustments will cause increased toxic
emissions of carbon monoxide and may result in
carbon monoxide poisoning.
Liquefied propane will expand 270 times into
flammable vapor, which is used as fuel for propane
engines. Proper training is recommended for those
operating propane powered machines in order to
limit the hazards related to the handling and storage
of propane fuel cylinders.
CHANGING OIL
The manufacturer recommends 10W30 oil.
1. Run engine for 5 minutes to warm the oil.
2. Make sure machine is on level surface, pad on
the floor. Place container under drain and open
the oil drain valve. Allow oil to drain completely.
3. Close drain valve and add 1 qt. Of 10W30 motor
oil. Check level and add if necessary.
REFUELING
The capacity of the 4E240 cylinder is 20lbs., 80% of
the total water capacity. Never overfill the cylinder.
Have the cylinder filled at a reputable propane
dealer.
4. Replace oil-fill cap assembly. Hand tighten only.
! CAUTION
DO NOT over fill oil and never run engine with low
oil level, this could cause damage to the engine
voiding your warranty.
Do not attempt to repair a propane cylinder yourself.
Return the cylinder to your propane dealer for
authorized service.
NOTE: When checking oil, remove dip stick, wipe
clean, then reinsert the dip stick into the engine. DO
NOT SCREW IN (check engine manufacturer
manual for recommended procedure). Remove dip
stick and observe oil level as indicated on dip stick.
STORING
Propane fuel cylinders whether full or empty should
be stored outside the building in a secure cylinder
storage cabinet in accordance with NFPA 58 5-4.2.1
! CAUTION
ADJUSTING BELT TENSION
Vertical Propane fuel cylinders must always be
stored in a vertical position. This position assures
that the discharge from the pressure relief valve or
other items will be largely vapor and not liquid which
will expand to 270 times to flammable vapor.
Tools required for this procedure are:
-
-
¾” (19mm) open end wrench
15/16” (24mm) deep well socket
1. Loosen mounting bolt on top side of machine
deck while holding adjusting nut on underside of
deck. NOTE: the mounting bolt must be
loosened before adjustment can be made.
2. Rotate adjusting nut counter clockwise with
socket to apply tension to belt.
The manufacturer reminds you that the fuel
cylinders should be removed from the machine
and placed in the proper storage cabinets
outside the building.
3. While holding the tension on the adjusting nut,
tighten the mounting bolt on top of the deck.
4. Check belt tension by pinching belt together.
Belt should depress only ½” (12mm)
NOTE: Local authorities may have additional
requirements for storage of fuel cylinders. Always
check with the local authorities for these additional
requirements.
Mounting Bolt
Machine Base
Tensioner
Tensioning Gauges
Adjusting Nut
Idler Pulley
LIGHTNING 86039180 05/23/07
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
2. Change oil and oil filters at 50 hours of service.
Use 10W30 Motor Oil or other no ash motor oils
designed for use in propane engines. Use of
non-recommended oil may void the engine
warranty. (see engine manual supplied with
documentation).
! WARNING
Before attempting any maintenance procedures on
the machine, close the service valve on the fuel tank
and stop the engine.
! CAUTION
Repairs and adjustments to the fuel system must be
made by an authorized, properly trained service
technician.
3. Check for loose nuts and/or bolts on entire
machine.
4. Examine all propane fuel components for leaks
or wear. Replace if necessary.
To keep the machine in good working condition,
simply follow the daily, weekly, and monthly
maintenance procedures.
5. Grease wheels. Use white lithium grease only
and no more than 1 pump of grease. More
grease than recommended will push the seals
and dust covers out, allowing dust and other
foreign materials to penetrate the bearing,
shortening the life of the bearings as well as
allowing grease to drop from the wheels to the
floor.
Keeping the machine clean and free from
accumulated dust, lint, and oil allows free air flow
across the engine to cool the engine properly.
Always use clean recoil dust filters. These can be
cleaned by washing them in a flow of water and
shaking dry. Extra filters may be ordered from
customer service.
MONTHLY MAINTENANCE
(every 80 hours of operation)
IMPORTANT: Preventative maintenance is the
responsibility of the operator.
1. Perform all daily and weekly services.
2. Torque head bolts.
DAILY MAINTENANCE
(every 4 hours of operation)
1. Check oil level (use 10W30 oil only).
2. Clean recoil filter.
3. Check valve clearance.
4. Torque valve cover bolts.
3. Check & Clean carburetor air filter.
5. Inspect spark plug. Replace if necessary.
6. Remove engine shroud and clean cooling fins.
4. Check belt tension by pinching belt together.
Belt should deflect only ½” (13mm).
NOTE: Consult specific engine owner’s manual for
the above steps 2-6.
5. Make sure all components are secure and tight.
(pad holder, fuel cylinder, etc.)
QUARTERLY MAINTENANCE
(every 250 hours of operation)
6. Check pad driver and pad, daily. (clean or
replace)
7. Clean machine, if compressed air is available
blow dust from machine and engine,
concentrating on the inside of engine shrouds.
Wash undercarriage.
1. Perform all of the monthly maintenance items.
2. Have engine serviced by authorized service
center. Including emissions check.
Keep a log book of all maintenance and repairs
performed on your machine.
WEEKLY MAINTENANCE
(every 20 hours of operation)
1. All checks made on a daily basis plus:
LIGHTNING 86039180 05/23/07
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
INSTALLING OR REMOVING PAD
DRIVER OR PADS
Consult an authorized distributor to assist you in
selecting the correct pad for your specific needs.
Pad driver installation:
1. Tip machine on the right side (dip stick down).
2. Place pad driver on drive shaft and spin pad
driver clockwise to install.
Pad Removal & Installation:
1. Tilt machine back on rear caster or service
position.
2. Remove center-lock from pad driver.
3. Remove pad from pad holder.
4. Center new pad on pad driver & secure with
center-lock ring.
Pad driver removal:
1. Apply down pressure on bell of machine deck.
2. Use ¾” open end wrench on top of drive shaft
exposed on top of deck.
3. Strike wrench with rubber mallet to break loose
the shaft from the pad driver. (counter-clockwise)
4. Remove pad driver by spinning it off counter-
clockwise.
LIGHTNING 86039180 05/23/07
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE TROUBLESHOOTING
PROBLEM.
CAUSE
SOLUTION
Will not start
No fuel or dirt in fuel line
Blown head gasket
Engine overload
See engine owners manual for servicing.
NOTE: ONLY properly trained service technicians
Should adjust or repair fuel system.
Dirty air cleaner
Faulty spark plug
Fuel system out of
adjustment
Defective ignition coil
No fuel or dirt in fuel line
Engine overload
Hard to start
See engine owners manual for servicing.
Dirty air cleaner
Faulty spark plug
Spark plug or head bolts
loose
Blown head gasket
Timing, Coil or Valves
need adjustment
Regulator need adjustment
Insufficient vacuum
Improper valve clearance
Dirt in fuel line
Lacks Power
See engine owners manual for servicing.
Faulty spark plug
Improper oil level
Worn rings
Odor of burned rubber
Engine overheats
Belt out of adjustment
Incorrect oil level
See “Adjusting Belt Tension” pg. 3-3
See engine owners manual for servicing.
Engine overload
Build up of dirt inside
engine shroud
High fuel consumption
Faulty spark plug
Dirty air cleaners
See engine owners manual for servicing.
Improper fuel system
adjustment
Machine stops suddenly Out of fuel
Faulty spark plugs
Change fuel cylinders
Clean adjust or replace spark plug
Pad not centered on pad
driver
Center pad or pad driver
Incorrect pad size
Low oil
Replace with proper pad
Add oil (see pg. 3-3)
LIGHTNING 86039180 05/23/07
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE TROUBLESHOOTING
PROBLEM.
CAUSE
SOLUTION
Bolts loose on engine or
deck
Excess vibration
Tighten all bolts
Pad not centered or
damaged pad
Center or replace pad
Incorrect oil level
Engine overload
Dirty filter
Check and adjust oil level
See engine owners manual for servicing.
See engine owners manual for servicing.
See engine owners manual for servicing.
Faulty spark plug
LIGHTNING 86039180 05/23/07
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
21” DECK GROUP
1
2
3
4
7A
7B
7C
5
27
26
(4)
6A
6B
25A
25B
8
9A
9B
10
11
24
23
22
21
12
13
20
19A
19B
28
14
15
18
17
16
LIGHTNING 86039180 05/23/07
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
21” DECK PARTS LIST
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
86262580
86262570
07093
07083
1
1
FOAM HAND GRIPS
FM HANDLE
Comes with
literature
3
N/A
ref
ENGINE OWNER’S MANUAL
4
5
86262830
86263140
86261970
86261880
86262800
86262730
86263030
86263200
86261980
86262010
86261960
86262770
86262380
86262050
86243840
86262600
86263210
86262090
86262300
07129
07089
07039
07068
07086
07123
07066
07018
07067
07116
07038
07017
07001
07150
500664
07022
07019
07027
07023
07014
07013
07084
07015
07151
07016
07121
07063
07025
07048
07002
07079
07111
07024
1
1
1
1
1
ref
ref
1
1
ref
1
1
1
1
1
1
1
1
1
2
ref
1
2
1
1
1
1
ref
1
KEY SWITCH
PLASTIC HOLDER
BATTERY BOX
6” KEY SWITCH BRACKET
KAWASAKI 17HP
HONDA 390 13HP
ONAN E124
6A
6B
7A
7B
7C
8
9A
9B
10
11
12
13
14
15
16
17
18
PULLEY 3.5
BATTERY CONNECTOR E124
BATTERY CONNECTOR KAWASAKI
BATTERY 12VOLT
HOUR METER
DECK 21” BLUE
BUMPER MOULDING
LABEL, LIGHTNING PRPN WINDSOR
FRONT BEARING ASSY. COMPLETE
PULLEY 6.2
BX40 BELT
CENTER LOCK
WHEEL 6” W/BKT
WHEEL (ONLY)
PAD DRIVER 21” FLEX
CASTER 3”
FLANGE
IDLER PULLEY
19A 86263540
19B 86263530
Service Only
20
21
22
23
24
86263100
86262280
86262560
86262780
86263460
TENSIONER
LP TANK (ALUM)
25A 86262930
25B 86262920
LP TANK (STEEL)
VELCRO TAPE
THROTTLE CABLE
PAD DRIVER 21” FLEX COMPLETE
CHOKE CABLE
26
27
28
29
30
86263520
86263470
86263070
86262330
86262720
1
1
-
-
Not Shown
Not Shown
HONDA STARTER (110 VOLT)
NOTE: For engine information not listed in this standard manual parts list, refer to appropriate Engine
Owner’s Manual.
LIGHTNING 86039180 05/23/07
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
24” DECK GROUP
1
2
3
4
7A
7B
7C
7D
5
27
26
(4)
6A
6B
25A
25B
8
9A
9B
9C
10
11
24
23
22
21
12
13
20
19A
19B
28
14
15
18
17A
17B
17C
16A
16B
16C
LIGHTNING 86039180 05/23/07
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
24” DECK PARTS LIST
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
86262580
86262570
07093
07083
1
1
FOAM HAND GRIPS
FM HANDLE
Comes with
literature
3
N/A
ref
ENGINE OWNER’S MANUAL
4
5
86262830
86263140
86261970
86261880
86262800
86262730
86263040
86263030
86263200
86261980
86262010
86262000
86261960
86262770
86262390
86262050
86243840
86262600
07129
07089
07039
07068
07086
07123
07131
07066
07018
07067
07116
07092
07038
07017
07032
07150
500664
07022
07019
1
1
1
1
1
ref
ref
ref
1
KEY SWITCH
PLASTIC HOLDER
BATTERY BOX
6” KEY SWITCH BRACKET
KAWASAKI 17HP
HONDA 390 13HP
ONAN P248
ONAN E124
PULLEY 3.5
BATTERY CONNECTOR E124
BATTERY CONNECTOR KAWASAKI
BATTERY CONNECTOR ONAN P248
BATTERY 12VOLT
HOUR METER
DECK 24” BLUE
BUMPER MOULDING
LABEL, LIGHTNING PRPN WINDSOR
FRONT BEARING ASSY. COMPLETE
PULLEY 6.2
6A
6B
7A
7B
7C
7D
8
9A
9B
9C
10
11
12
13
14
15
1
ref
ref
1
1
1
1
1
1
1
16A 86263210
Onan P248
Honda, Onan
E124
16B 86263250
07090
ref
PULLEY 8.5
16C 86263240
17A 86262110
17B 86262140
17C 86262120
07055
07028
07031
07069
07023
07014
07013
07104
07015
07151
07016
07121
07063
07025
07048
07002
07080
07111
07024
07109
07117
ref
1
ref
ref
1
2
ref
1
2
1
1
1
1
ref
1
1
1
-
-
-
-
PULLEY 7.0
BX42 BELT
BX45 BELT
BX43 BELT
CENTER LOCK
WHEEL 6” W/BKT
WHEEL (ONLY)
PAD DRIVER 24” FLEX
CASTER 3”
FLANGE
Kawasaki
Onan P248
18
86262300
19A 86263540
19B 86263530
Service Only
20
21
22
23
24
86263120
86262280
86262560
86262780
86263460
IDLER PULLEY
TENSIONER
25A 86262930
25B 86262920
LP TANK (ALUM)
LP TANK (STEEL)
VELCRO TAPE
THROTTLE CABLE
PAD DRIVER 24” FLEX COMPLETE
CHOKE CABLE
HONDA STARTER (110 VOLT)
20HP REGULATOR BRACKET
CHOKE BRACKET
26
27
28
29
30
31
32
86263520
86263470
86263080
86262330
86262720
86261860
86262340
Not Shown
Not Shown
Not Shown
Not Shown
NOTE: For engine information not listed in this standard manual parts list, refer to appropriate Engine
Owner’s Manual.
LIGHTNING 86039180 05/23/07
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
27” DECK GROUP
1
2
3
4
7A
7B
7C
7D
5
27
26
(4)
6A
6B
25A
25B
8
9A
9B
9C
10
11
24
23
22
21
12
13
20
19A
19B
28
14
15
18
17A
17B
16A
16B
LIGHTNING 86039180 05/23/07
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
27” DECK PARTS LIST
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
86262580
86262870
07093
07083
1
1
FOAM HAND GRIPS
FM HANDLE
Comes with
literature
3
N/A
ref
ENGINE OWNER’S MANUAL
4
5
86262830
86263140
86261970
86261880
86262800
86262730
86263040
86263030
86263200
86261980
86262010
86262000
86261960
86262770
86262400
86262050
86243840
86262600
07129
07089
07039
07068
07086
07123
07131
07066
07018
07067
07116
07092
07038
07017
07033
07150
500664
07022
1
1
1
1
1
ref
ref
ref
1
KEY SWITCH
PLASTIC HOLDER
BATTERY BOX
6” KEY SWITCH BRACKET
KAWASAKI 17HP
HONDA 390 13HP
ONAN P248
ONAN E124
PULLEY 3.5
BATTERY CONNECTOR E124
BATTERY CONNECTOR KAWASAKI
BATTERY CONNECTOR ONAN P248
BATTERY 12VOLT
HOUR METER
DECK 27” BLUE
BUMPER MOULDING
LABEL, LIGHTNING PRPN WINDSOR
FRONT BEARING ASSY. COMPLETE
6A
6B
7A
7B
7C
7D
8
9A
9B
9C
10
11
12
13
14
15
1
ref
ref
1
1
1
1
1
1
Honda, Onan
E124
Kawasaki,
Onan P248
Honda, Onan
E124
16A 86263230
16B 86263250
17A 86262200
17B 86262190
07034
07090
07054
07035
1
ref
1
PULLEY 9.4
PULLEY 8.5
BX51 BELT
BX50 BELT
Kawasaki,
Onan P248
ref
18
86262300
07023
07014
07013
07085
07015
07151
07016
07121
07063
07025
07048
07002
07081
07111
07024
07109
07117
1
2
ref
1
2
1
1
1
1
ref
1
1
1
-
CENTER LOCK
WHEEL 6” W/BKT
WHEEL (ONLY)
PAD DRIVER 27” FLEX
CASTER 3”
FLANGE
19A 86263540
19B 86263530
Service Only
20
21
22
23
24
86263110
86262280
86262560
86262780
86263460
IDLER PULLEY
TENSIONER
25A 86262930
25B 86262920
LP TANK (ALUM)
LP TANK (STEEL)
VELCRO TAPE
THROTTLE CABLE
PAD DRIVER 27” FLEX COMPLETE
CHOKE CABLE
HONDA STARTER (110 VOLT)
20HP REGULATOR BRACKET
CHOKE BRACKET
26
27
28
29
30
31
32
86263520
86263470
86263090
86262330
86262720
86261860
86262340
Not Shown
Not Shown
Not Shown
Not Shown
-
-
-
NOTE: For engine information not listed in this standard manual parts list, refer to appropriate Engine
Owner’s Manual.
LIGHTNING 86039180 05/23/07
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
30” STRIPPER GROUP
1
6A
6B
6C
2
36
3
37
4
34
7
35
5A
5B
8
9
38
13A
13B
14
16
33
32
14
10
15
11
17
30
29
31
29
12
19
20
18A
18B
27A
27B
21
22
26
23
28
24
25
LIGHTNING 86039180 05/23/07
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
30” STRIPPER PARTS LIST
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
86262580
86262570
86233140
86262830
86261970
86261880
86263030
86262730
86262800
86262310
86262180
86262740
86262500
86262680
86263260
07093
07083
07089
07129
07039
07068
07066
07123
07086
07046
07078
07112
07107
07120
07108
07067
07116
07077
07105
07017
07106
07072
07071
07170
07149
07060
07061
07057
07169
07075
07015
07121
07016
07110
07070
07040
07152
07082
07038
07048
07002
07025
1
1
1
1
1
1
1
ref
ref
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
1
2
2
2
1
6
1
1
1
1
2
2
2
1
1
2
1
1
FOAM HAND GRIPS
FM HANDLE
PLASTIC HOLDER
KEY SWITCH
BATTERY BOX
6” KEY SWITCH BRACKET
ONAN E124
HONDA 390 13HP
KAWASAKI 17HP
CENTRIFUGAL SWITCH
BX49 BELT
4
5A
5B
6A
6B
6C
7
8
9
10
11
12
HOOD ASSY. TWIN (ALUM) BLUE
EXPANDED METAL PLATE 4.5 X 14
GEAR BOX TWIN HEAD
PULLEY 7.0 X 5/8
BATTERY CONNECTOR ONAN E124
BATTERY CONNECTOR KAWASAKI 17HP
HANDLE GUSSETT
HEAT SHIELD FOIL MATERIAL
HOUR METER
HEAT SHIELD SUPPORT PLATE
BRUSH PLATE CLAMP
SPRING CLIP
TRANSPORT WHL – FRNT SPRT
KEY STOCK ¼ X 3
MOUNTING PLATE TWIN HEAD
ALUMINUM HUB
CENTRAL FLEX
STRIP BRUSH (1 SET)
LUGS L-800
CASTER 3”
TENSIONSER
IDLER PULLEY
SPLASH GUARD TRACKER
DELRIN BEARING 1”
WHEEL 10” AIR FILLED
WHEEL SPACER ½”
TWIN HEAD STRIP FRAME
BATTERY 12VOLT
13A 86261980
13B 86262010
14
15
16
17
86262690
86262700
86262770
86262710
18A 86262040
18B 86263380
19
20
21
22
23
24
25
26
86263480
86262840
86262970
86261920
86262320
86263410
86262940
86262280
27A 86263460
27B 86262780
28
29
30
31
32
33
34
35
36
86263370
86262440
86263550
86263560
86263490
86261960
86263520
86263470
86262920
VELCRO TAPE
THROTTLE CABLE
LP TANK (STEEL)
Comes with
Literature
37
N/A
ref
Engine Owner’s Manual
38
39
40
41
86243840
86263430
86262340
86263220
500664
07097
07117
07026
1
-
-
LABEL, LIGHTNING PRPN WINDSOR
SUPPORT
CHOKE BRACKET
PULLEY 3.0
Not Shown
Not Shown
Not Shown
-
NOTE: For engine information not listed in this standard manual parts list, refer to appropriate Engine
Owner’s Manual.
LIGHTNING 86039180 05/23/07
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
KAWASAKI FUEL LOAD BLOCK
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
9
86262270
86262620
86263340
86262790
86263510
86262650
86263420
86262030
86261870
86262660
07134
07103
07156
07135
07007
07132
07155
07100
07101
07133
1
1
1
1
1
1
1
1
1
1
CARBURETOR ASSEMBLY
FUEL LOAD BLOCK
RUBBER CAP ¼
INSULATOR
VACUUM TEE
GASKET AIR FILTER
STUD M-6 X 130
BRASS PLUG 1/8
3/8 HOSE X ¼ MP ELBOW
GASKET AIR FILTER
10
Note: For engine information not listed in the standard parts list, refer to the appropriate engine parts
manual.
5
3
10
1
4
6
7
1
2
8
10
9
LIGHTNING 86039180 05/23/07
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
KAWASAKI WIRING DIAGRAM
STARTER
-
+
M
12 V BATTERY
CHARGING SYSTEM
KEY SWITCH
ALT
STATOR
A-1
A-3
A-3
A-2
ENGINE HARNESS
CONNECTOR
A-1
A-2
BY-PASS DIODE
FUEL LOCKOFF
LOW OIL PRESSURE
CUTOFF SWITCH (NO)
HOUR METER
SWITCH
YELLOW
BLUE
BLUE
BLUE
BLUE
NOTE: RED WIRE CONNECTS
TO LEFT SIDE OF SWITCH. ALL
OTHER WIRES CONNECT TO
RIGHT SIDE OF SWITCH
YELLOW
BLUE MALE CONNECTOR
TO ELECTRIC LOCK OFF
BLUE FEMALE
CONNECTOR
RED
LOW OIL PRESSURE
SWITCH
BLUE PIGGY BACK
CONNECTOR
BLUE FEMALE
CONNECTOR
BLUE FEMALE CONNECTOR
TO VOLTAGE REGUALTOR
BLUE FEMALE CONNECTOR
TO STARTER SOLENOID
YELLOW LOOP TO
STARTER SOLENOID
LIGHTNING 86039180 05/23/07
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
KAWASAKI FUEL SYSTEM
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
9
86263270
86262900
86262530
86262760
86262610
86262540
86263320
86262630
86262550
07012
07006
07009
07003
07004
07010
07118
07113
07011
1
1
1
1
1
1
1
1
1
QUICK COUPLER
LP HOSE TO TANK
FITTING ¼ X 90 STREET ELBOW
HOSE, VAC
FUEL HOSE
FITTING 3/8 BARB X 3/8 MP
REGULATOR
FUEL LOCK W/FILTER 12VOLT
FITTING 1/4BARB X 1/4MP
NOTE: For engine information not listed in this Standard Parts List, refer to the appropriate Engine
Parts Manual.
6
5
7
4
2
9
8
3
LIGHTNING 86039180 05/23/07
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA FUEL SYSTEM
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
86263270
86262900
86262530
86262760
86262610
86262540
86263310
86262880
86262330
86262520
86263500
86262890
07012
07006
07009
07003
07004
07010
07064
07065
07011
07008
07042
07005
1
1
1
3
1
1
1
1
2
1
1
1
QUICK COUPLER
LP HOSE TO TANK
FITTING ¼ X 90 STREET ELBOW
HOSE, VAC
FUEL HOSE
FITTING 3/8 BARB X 3/8 MP
REGULATOR
LOCKOFF
FITTING 1/4BARB X 1/4MP
FITTING 3/8 FLARE X 1/4MP
VAC TEE
10
11
12
LP HOSE REG TO LOCK
NOTE: For engine information not listed in this Standard Parts List, refer to the appropriate Engine
Parts Manual.
6
5
7
2
4
9
3
10
11
1
4
9
4
12
8
LIGHTNING 86039180 05/23/07
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
KILL SWITCH ASSEMBLY
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
NOTES:
1
2
86261930
86263450
07056
07050
1
1
ARM & SPRINGS (2 EACH)
SWICTH MICRO (KILL)
NOTE: For engine information not listed in this Standard Parts List, refer to the appropriate Engine
Parts Manual.
1
2
LIGHTNING 86039180 05/23/07
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
CLUTCH AND SWITCH ASSEMBLY
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
86261930
86263440
86262360
86263350
86262460
86262350
07056
07049
07047
07044
07045
07043
1
1
1
1
1
1
ARM & SPRINGS (2 EACH)
SWITCH (CLUTCH)
CLUTCH SWITCH ASM. COMPLETE
SPACER
ELECTRIC CLUTCH
CLUTCH ARM
NOTE: For engine information not listed in this Standard Parts List, refer to the appropriate Engine
Parts Manual.
1
2
3
4
5
5
LIGHTNING 86039180 05/23/07
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
BELT CHART/NOTES
PART NO. PRV NO. DESCRIPTION NOTES:
86262060
86262070
86262080
86262090
86262100
86262110
86262120
86262130
86262140
86262150
86262160
86262170
86262180
86262190
86262200
86262210
86262220
86262230
86262240
86262250
86262260
07052
07041
07020
07027
07021
07028
07069
07030
07031
07148
07091
07053
07078
07035
07054
07029
07037
07036
07073
07074
07087
BX34 BELT
BX36 BELT
BX38 BELT
BX40 BELT
BX41 BELT
BX42 BELT
BX43 BELT
BX44 BELT
BX45 BELT
BX46 BELT
BX47 BELT
BX48 BELT
BX49 BELT
BX50 BELT
BX51 BELT
BX52 BELT
BX53 BELT
BX54 BELT
BX55 BELT
BX56 BELT
BX58 BELT
STANDARD CLUTCH
BELT PART NO.
W/ELECTRIC CLUTCH
BELT PART NO.
STANDARD CLUTCH
BELT PRV NO.
W/ELECTRIC CLUTCH
BELT PRV NO.
MACHINE PRV MACHINE NO.
10023000
10023020
10023040
10023030
10023060
10023080
10023070
10023090
10023110
10023110
L21H13
L21K17
L24H13
L24ER22
L24K17
L27H13
L27ER22
L27K17
LS30H13
LS30H13
86262090
86262090
86262140
86262110
86262120
86262200
-
86262190
86262180
86262180
07027
07027
07031
07028
07069
07054
N/A
07035
07078
07078
86262110
86262110
86262170
86262130
86262150
-
86262260
86262210
-
07028
07028
07053
07030
07148
-
07087
07029
N/A
-
N/A
LIGHTNING 86039180 05/23/07
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
|