USE AND CARE MANUAL
GAS COOKTOP MODELS: CTG304D, CTG305D, CTG365D
IMPORTANT: Before beginning use please read these instructions completely and
carefully.
INSTALLER: Leave this owner’s manual with the cooktop.
OWNER: Please retain this manual for future reference.
CNP INDUSTRIES, INC.
P.O. BOX 18645
ANAHEIM, CA 92817
(714) 482-2320 ● (714) 482-2337 FAX
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. For your safety:
-Do not obstruct the flow of combustion and ventilation air to the unit.
-Keep appliance area clear and free from combustible material.
2. Never use this product for warming or heating a room.
3. An approved gas regulator is supplied and should be used with this appliance.
POWER SUPPLY – Requires a 120 VAC, 60 HZ, 15 Amp single-phase circuit for all models. A three prong grounded
receptacle is required. Plan the installation for the unit so that the location of the three-prong
receptacle is within three (3) feet of the right rear bottom corner of the cooktop and accessible from
the front of the cooktop. See FIG – 6.
Warning - The grounding prong must not be cut or removed from the power cord.
- A three prong grounded receptacle must be used.
- The power source must be properly polarized. Reverse polarity will cause continuous sparking of the
electrodes.
- Do not use a Ground Fault Circuit Interrupter (GFCI). The electrode
spark ignition module will cause GFCI’s to trip.
This appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local
codes, in accordance with National Electric Code ANSI/NFPA 70. The correct voltage, frequency and amperage must be
supplied to the appliance from an individual, dedicated grounded circuit which is protected by a properly sized circuit
breaker or time delay fuse. The required voltage, frequency and amperage ratings are listed on the product data plate and
also shown above.
This appliance is factory equipped with a 5-foot long power supply cord having a 3-prong grounded plug. This plug must
be inserted into a mating grounded receptacle in accordance with National Electrical Code and applicable state, municipal
and local codes.
In Canada, installation must be in accordance with CSA C22.1 Canadian Electrical Code Part-1 and/or local codes.
GAS SUPPLY PRESSURE – NATURAL GAS: 6 to 14 inches water column (Manifold at 4-inches)
PROPANE GAS: 11 to 14 inches water column (Manifold at 10-inches)
CAUTION: For LP gas installations, the LP gas tank must have its own high pressure
regulator. This is in addition to the pressure regulator supplied with the cooktop.
Check your local building codes for the proper method of installation. In the absence of local codes, this appliance should
be installed in accordance with the National Fuel Gas Code ANSI Z223.1. Be certain that the appliance being installed is
correct for the gas service provided. Refer to the data plate located on the bottom of the cooktop and pressure
requirements above.
In Canada, installation must be in accordance with current CAN/CGA B149.1 and 2 gas installation codes and/or local
codes.
NOTE: The cooktop settings for natural gas are established at the factory. No field adjustments are required.
Natural gas cooktops can be converted for Liquid Propane (LP) use by qualified servicers only. A factory supplied
“LP” conversion kit is available. To obtain kit contact your local dealer.
MODEL CTG304D – LP KIT #10691.00
MODEL CTG305D – LP KIT #10692.00
MODEL CTG365D – LP KIT #10693.00
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRACTICES TO AVOID
PERSONAL INJURY
IMPORTANT SAFETY INSTRUCTIONS
C. Use high range settings on
range only when necessary.
Heat oil slowly on low to
medium setting.
B. NEVER PICK UP A
THE RISK OF FIRE,
FLAMING PAN – You may
be burned.
ELECTRIC SHOCK OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
C. DO NOT USE WATER,
including wet dishcloths or
towels – a violent steam
explosion will result.
A. Use this unit only in the
manner intended by the
manufacturer. If you have any
questions, contact the
manufacturer.
D. Do not leave range unattended
when cooking.
E. Always use cookware and
utensils appropriate for the
type and amount of food
being prepared.
D. Use an extinguisher ONLY if:
B. Before servicing or cleaning
unit, switch power off at
service panel and lock service
panel to prevent power from
being switched on
1. You know you have a
class ABC extinguisher,
and you already know
how to operate it.
WARNING – TO REDUCE
THE RISK OF INJURY TO
PERSONS, IN THE EVENT OF
A GREASE FIRE, OBSERVE
THE FOLLOWING:
accidentally.
2. The fire is small and
contained in the area
where it started.
WARNING – TO REDUCE
THE RISK OF SHOCK, OR
INJURY TO PERSONS,
A. SMOTHER FLAMES with a
close-fitting lid, cookie sheet,
or other metal tray, then turn
off the gas burner or the
electrical element. BE
3. The fire department is
being called.
OBSERVE THE FOLLOWING:
A. Keep exhaust hoods, filters
and grease-laden surfaces
clean.
B. Always turn hood ON
when cooking at high heat.
4. You can fight fire with
your back to an exit.
CAREFUL TO PREVENT
BURNS. If the flames do not
go out immediately
EVACUATE AND CALL
THE FIRE DEPARTMENT.
*************************************************************************************************
When properly used and cared for
your new Wind Crest Cooktop has
been designed to be a safe, reliable
appliance. When using kitchen
appliances, basic safety
precautions must be followed,
including the following:
gas shut-off valve is located so that
you know how and where to turn
off the gas to the cooktop.
light even though the electric
igniters click. See cleaning and
general care section.
If you smell gas, your installer has
not done a proper job of checking
for leaks. Connections can loosen
in transit. If the connections are
not perfectly tight, you can have a
small leak and therefore a gas
smell. Finding a gas leak is not a
“do-it-yourself” procedure. Some
leaks can only be found with the
burner control in the ON position.
The cooktop is factory assembled
for natural gas. It should be
correctly adjusted by a qualified
service person or installer for the
type of gas with which it is used.
Read this Use and Care annual
carefully before using your new
cooktop to reduce the risk of fire,
electric shock, or injury to persons.
Begin by insuring proper
Installation and servicing. Follow
the installation instructions
For proper lighting and
provided with this product. Have
the cooktop installed and grounded
by a qualified technician. Have
the installer show you where the
performance of the burners, keep
the igniters clean. It is necessary
to clean these when there is a boil
over, or when the burner does not
4
Download from Www.Somanuals.com. All Manuals Search And Download.
When using the cooktop: DO NOT TOUCH THE
BURNER GRATES OR THE IMMEDIATE
SURROUNDING AREA. Areas adjacent to the
burners may become hot enough to cause burns.
Do not repair or replace any part of the appliance
unless specifically recommended in this manual. All
other servicing should be referred to a qualified
technician.
Never leave the burners unattended when using high
flame settings. Boil overs cause smoking and greasy
spillovers that may ignite. More importantly, if the
flame is smothered, unburned gas will be coming into
the room. See “What to do if you smell gas,” page 2.
Children should not be left alone or unattended in an
area where appliances are in use. They should never
be allowed to sit or stand on any part of the appliance.
Caution: Do not store items of interest to children
above the cooktop or at the back. If children should
climb onto the appliance to reach these items, they could
be seriously injured.
Always use utensils that have flat bottoms. Hold the
handle of the pan to prevent movement of the utensil
when stirring or turning food.
Do not store flammable materials on or near the
cooktop.
To minimize burns, ignition of flammable materials, and
unintentional spillovers, position handles of utensils so
that they do not extend over adjacent work areas,
burners, or the edge of the cooktop.
Do not use water on grease fires. Turn appliance off
and smother fire with baking soda or use a dry chemical
or foam-type extinguisher.
During cooking, set the burner control so that the
flame heats only the bottom of the pan and does not
extend beyond the edge of the pan.
Never let clothing, potholders, or other flammable
materials come in contact with the burners or the
burner grates, until they are cool to the touch.
Only certain types of glass, heat-proof glass-ceramic,
ceramic, earthenware, or other glazed utensils are
suitable for cooktop use. This type of utensil may
break with sudden temperature changes. Use only on
low or medium flame settings according to
Use only dry potholders; moist or damp potholders on
hot surfaces may cause burns from steam. Do not use a
towel or other bulky cloth in place of potholders. Do not
let potholders touch hot burners or burner grates.
manufacturer’s directions.
For personal safety, wear proper apparel. Loose
fitting garments or hanging sleeves should never be
worn while cooking.
If the cooktop is near a window, be certain the curtains
do not blow over or near the burners; they could catch
on fire.
Do not use aluminum foil to line any part of the
cooktop. Improper use of a foil liner could result in a
shock, fire hazard or it could obstruct the flow of
combustion and ventilation air. Foil is an excellent heat
insulator and heat will be trapped beneath it. This will
upset the cooking performance and can damage the
cooktop finish.
In the event a burner goes out and gas escapes, open a
window or door. Do not attempt to use the cooktop until
the gas has had time to dissipate. Wait at least 5
minutes before using the cooktop.
Clean the cooktop with caution. Avoid steam burns;
do not use a wet sponge or cloth to clean the cooktop
while it is hot. Some cleaners produce noxious fumes if
applied to a hot surface.
Warning: The appliance is for cooking. Based on
safety considerations never use the cooktop to warm or
heat a room. Also, such use could be damaging to the
cooktop.
Turn the ventilator OFF in case of fire or when
intentionally “flaming” liquor or other spirits on the
cooktop. The blower, if in operation, could unsafely
spread the flames.
Do not heat unopened food containers; a buildup of
pressure may cause the container to burst.
To achieve optimum cooking performance do not use
warped pots and pans. For safety reasons do not use
unbalanced pots and pans – heavy handles or warped
bottoms can cause pans to be unstable
Match the pot size to the burner and flame size. The
flame should be equal to or smaller than the pan bottom.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
California Proposition 65 – Warning: Burning gas cooking fuel generates some by-products which are on the list of
substances which are know by the state of California to cause cancer or reproductive harm. California law requires
businesses to warn customers of potential exposure to these substances. To minimize exposure to these substances,
always operate this unit according to the instructions contained in this booklet and provide good ventilation.
♦ SAVE THESE INSTRUCTIONS ♦
BEFORE USING YOUR COOKTOP FOR THE FIRST TIME:
1.
2.
Remove all packaging materials and labels before using your cooktop.
Check that you have these items:
CTG304D:
- 2 Burner Grates
- 4 Single Burner caps
- Use and Care Manual
CTG305D:
- 2 Burner Grates
- 4 Single Burner Caps
- 1 Center Burner Assembly (see page 9)
- Use and Care Manual
CTG365D:
- 3 Burner Grates
- 4 Single Burner Caps
- 1 Center Burner Assembly (see page 9)
- Use and Care Manual
3.
Record the Model and Serial Number for any future contacts with your servicer or the factory. Data
label is located on bottom of cooktop.
Model #: ____________________
Serial #: _____________________
Date Installed: ________________
Keep a copy of your purchase invoice for future reference.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Burners
Model CTG304D
(Grates not shown)
4
1
3
4
3
2
1
2
1 – Right Front Burner Control
9,000 BTU/HR
3 – Left Rear Burner Control
12,000 BTU/HR
2 – Left Front Burner Control
15,000 BTU/HR
4 – Right Rear Burner Control
15,000 BTU/HR
Model CTG305D
(Grates not shown)
5
5
4
3
2
1
4
2
3
1
1 – Right Front Burner Control
9,000 BTU/HR
4 – Left rear Burner Control
12,000 BTU/HR
2 – Left Front Burner Control
15,000 BTU /HR
5 – Right Rear Burner Control
9,000 BTU/HR
3- Center Burner Control
18,500 BTU/HR
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Model CTG365D
(Grates not shown)
5
4
1
2
3
1 – Left Rear Burner Control
12,000 BTU/HR
4 – Right Front Burner Control
9,000 BTU/HR
2 – Left Front Burner Control
15,000 BTU/HR
5 – Right Rear Burner Control
15,000 BTU/HR
3 – Center Burner Control
18,500 BTU/HR
Control Knob & Graphic
OFF
HIGH HEAT
LOW HEAT
ULTRA - LOW HEAT
CENTER BURNER ONLY
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL OPERATION
Each burner has an individual control knob allowing infinite heat selection between high and low.
-
-
-
-
9,000 Btu/hr burner adjusts to 1300 Btu/hr Low
12,000 Btu/hr burner adjusts to 1600 Btu/hr Low
15,000 Btu/hr burner adjusts to 2100 Btu/hr Low
18,500 Btu/hr burner adjusts to 4100 Btu/hr Low and 500 Btu/hr Ultra-Low
The control knobs are plated metal and can be removed (by pulling straight upward) for improved cleaning. Be sure the
control is in the OFF position before removing a knob. When cleaning in the area of the controls, use a damp cloth to
wipe surfaces only after cooktop has cooled. DO NOT USE CLOTHS THAT ARE SOPPING WET.
To operate a control, push down and rotate counter clockwise. The high heat position has a detent for easy selection. The
center burner control (CTG305D & CTG365D only) has detents at the HIGH, MEDIUM and LOW heat positions. The
controls rotate counter clockwise from OFF to LOW. Rotate the control knob clockwise to the full OFF position.
SIMMER BURNER CAP
BURNER HEAD
BURNER HEAD WITH
PROCELAIN CAP
LOCATING PIN AND
NOTCH IN BURNER
RING ALIGNS WITH
HOLE AND TAB
IN BURNER HEAD
GAS PORTS
SKIRT
TAB
BURNER BASE
NOTCH
BURNER RING (TOP VIEW)
INSERT BOTTOM PIN
ON BURNER HEAD INTO
HOLE IN BURNER BASE
SINGLE BURNER ASSEMBLY
(INSERT TAB INTO NOTCH)
LOCATING
HOLE
BURNER BASE
LOCATED IN COOKTOP
CENTER BURNER ASSEMBLY
FIG - 7
CAUTION: IMPROPER POSITIONING OF BURNER CAN DAMAGE COOKTOP AND CAUSE
INJURY TO PERSONS.
CORRECT POSITIONING RESULTS IN EVEN FLAME DISTRIBUTION AND
APPEARANCE.
BURNER ASSEMBLY
Burners are sealed for easier cleaning.
Single Burner – The burner head has two locating tabs that fits into notches in the burner base (located in cooktop) For
proper burner operation the burner head tabs must be located in the burner base notches. See illustration.
Center Burner – On those models that have a center burner, the sequence of assembly and positioning of the
components is important for proper burner operation. The order of the assembly is – burner ring first, skirt next and
the burner head last. The simmer cap can be positioned in any sequence. The burner head and burner ring index with
pins, tabs and notches to indicate proper assembly. See illustration.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Electronic Ignition
Each burner has an igniter that sparks when the burner is turned on, or during re-ignition if the flame is extinguished.
When a flame is present the igniter will stop sparking. If a cross draft is present the flame can be affected and some
sparking can occur. This is normal.
The igniter can get dirty due to normal cooking splatter or spills. This may cause nuisance sparking. The igniter can be
cleaned by using a Scotch Brite cleaning pad to clean the igniter disk. Do not touch the igniter on the burner if the control
is in the ON position. Hold the pad against the igniter tip and using light pressure rotate the pad in a circular motion. A
few rotations are usually sufficient to clean the surface.
If a burner does not ignite in approximately 4 seconds, check the positioning of the burner head to be sure the tabs and
notches are properly aligned.
Grates
Grates are to be properly installed onto cooktop.
Model CTG304D – Has two symmetrical grates. Position side by side into recessed area of cooktop over burners.
Model CTG305D – Has two non-symmetrical grates. Position side by side into recessed area of cooktop over burners.
Center burner section of grates match each other over center burner.
Model CTG365D – Has three grates; two larger symmetrical grates and one smaller center grate. Position larger grates
into recessed area of cooktop on each side of control area. Smaller center grate fits between the larger grates.
CAUTION: THE GRATES ARE HEAVY. USE BOTH HANDS AND SPECIAL CARE WHEN LIFTING.
PROVIDE SURFACE PROTECTION WHEN PLACING ON COUNTERTOP.
CLEANING AND GENERAL CARE
CAUTION: CONTROLS SHOULD BE OFF AND SURFACES COOL BEFORE
CLEANING.
Control Knob
When in place on cooktop, wipe with a damp cloth. A mild soap solution can be used. Do not soak. If removed and
cleaned, be sure the knob has dried fully before reinstalling.
DO NOT FORCE KNOB ONTO CONTROL STEM. ALIGN THE FLAT ON STEM WITH THE FLAT ON
KNOB AND GENTLY PUSH INTO PLACE.
Burner Base
Use cloth or Scotch Brite pad dampened with a water and detergent solution. Rub in circular motion.
AVOID SCRATCHING STAINLESS STEEL WITH SCOTCH BRITE PAD.
Burner Head
Scotch Brite pad dampened with a water and detergent solution. Rub in circular motion.
AVOID USING HARSH SCOURING PADS AND ABRASIVE CLEANERS.
If parts become clogged, clean using a paper clip. Do not use toothpick, which can break and clog the parts.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Grates
The grates are porcelain enamel coated cast iron. Non-abrasive cleaners are preferred. Use a hot or warm water and
detergent solution. Mild abrasive cleaners, such as Bon Ami®, are acceptable. After cleaning always rinse and dry
immediately. If grates are extremely dirty, a Scotch Brite pad will aid cleaning. Acidic and sugar-laden spills attack the
porcelain – remove soil immediately.
Note: The grates will show discoloration, crazing, and chips due to high heat exposure. This is normal.
Stainless Steel
Although stainless steel is strong and durable, and resists most food stains it can be affected by some compounds and food
spills. Remove spills and salt as soon as safely possible – don’t leave exposed for long periods of time. Always rub
lightly in direction of brush (graining) lines. Chlorine can be corrosive – always check ingredients on cleaner label.
Non-abrasive cleaners or hot water and detergent solutions are recommended. Always rinse and dry immediately.
Hard water spots can be removed with household white vinegar.
Stainless Steel Magic® is an acceptable cleaner/polish to protect the stainless finish and appearance. Mild abrasive
cleaners such as Bon Ami®, Kleen King Stainless Steel Cleaner, Cameo Aluminum and Stainless Cleaner can be used
depending on the clean up necessary.
The high quality 300-series stainless steel can discolor when exposed to high heats. Bar Keepers Friend® or Revere
Stainless Steel Cleaner will remove the discoloration. Always rub in the direction of the brush (graining) lines.
Igniter
Avoid excess water on igniter. Damp or wet igniters can prevent the burner from lighting. Use a Scotch Brite pad, dry or
damp, to clean stainless tip. Use a cotton swab dampened with water, ammonia, or formula 409 to clean ceramic.
WARRANTY
FULL ONE YEAR WARRANTY – Covers repair and replacement of parts found to be defective due to materials and
workmanship, for one year from date of purchase. Keep proof of purchase handy for inspection. SERVICE MUST BE
PROVIDED BY A FACTORY AUTHORIZED SERVICE AGENCY, DURING NORMAL WORKING HOURS.
ITEMS NOT COVERED IN WARRANTY:
1. Damage or repairs due to service by an unauthorized agency or use of unauthorized parts.
2. Service visits to teach you how to use the appliance.
3. Correct installation related problems – you are responsible for providing electrical wiring and other
connecting items.
4. Reset circuit breakers or replace fuses.
5. Damage caused by abuse, accident, alteration, misuse, local code violations.
6. Failure due to other than normal house use.
7. Travel fees and associated charges incurred when product in a location with limited or restricted access (i.e.
airplane flights, ferry charges, isolated geographic locations, unusual wait times, etc.)
FOR SERVICE CONTACT YOUR DEALER FOR NAME OF FACTORY AUTHORIZED
SERVICER IN YOUR AREA OR CALL THE FACTORY TOLL FREE:
(877) 387-6721
This warranty applies to appliances used in residential operations only. The warranty is for products purchased and
retained in the 50 states of the USA, the District of Columbia, and Canada. If the appliance is sold by the original
purchaser during the warranty period the new owner is protected until expiration of the original purchasers warranty. This
warranty gives you specific legal rights. You may also have other rights, which vary from state to state.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|