This Manual is Bookmarked
Operating Instructions — Parts Manual
14-Inch Vertical Band Saws
Models: 8201, 8203, 8201VS and 8203VS
WHM TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Ph.: 800-274-6848
Part No. 9078171
Revision C2 04/07
Copyright © 2007 WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Cover Page.................................................................................................. 1
General Specifications ................................................................................. 4
Operating Precautions ................................................................................. 5
Set-up and Operation ................................................................................... 7
Wiring Diagrams .......................................................................................... 8
Operating Instructions ................................................................................ 10
Maintenance .............................................................................................. 14
Troubleshooting.......................................................................................... 18
Replacement Parts..................................................................................... 19
3
Download from Www.Somanuals.com. All Manuals Search And Download.
General Specifications
Wilton’s 14-inch Tradesman Vertical Band Saws
are specially designed to effectively cut a variety of
materials including wood, plastic, bakelite, com-
posites, ferrous and non-ferrous metals. Models
8201 and 8203 are wood and metal cutting band
saws.
Wilton’s Model 8201VS and 8203VS 14-inch
Tradesman Variable Speed Band Saws are ideally
suited for metal cutting only with an infinitely
variable speed range from 116 to 334 SFPM. The
variable speed drive system allows the operator to
fine-tune the blade speed to the material being cut
to maximize the life of today’s bi-metal blades.
These versatile and dependable saws are capable
of contour cutting, straight cutting and re-sawing,
and these band saws can cut delicate curves in
thick or thin stock.
Specifications
4
Capacity
8201
8203
8201VS
8203VS
Standard ..............6-in. under guide ..... 6-in. under guide ....... 6-in. under guide ...... 6-in. under guide
With 12-in. Riser ..12-in. under guide ... 12-in. under guide ..... 12-in. under guide .... 12-in. under guide
Blade to frame .....13.5-in. .................... 13.5-in. .....................13.5-in. ..................... 13.5-in.
Motor
Rating ..................1 HP 1-Ph ............... 1 HP 3-Ph ................. 1 HP 1-Ph ................ 1 HP 3-Ph
Voltage.................115 vac.................... 220/440 vac .............. 115 vac .................... 220/440 vac
Speed ..................1725 rpm................. 1725 rpm .................. 1725 rpm.................. 1725 rpm
Cutting Speeds
Wood (SFPM)......3300 ........................ 3300 ......................... 2600 ......................... 2600
Metal (SFPM) .......39, 57, 78, 107, ....... 39, 57, 78, 107, ........ 116 – 334 ................. 116 – 334
142, 196, 278 .......... 142, 196, 278............ Variable Speed ......... Variable Speed
Dimensions
Length .................20 Inches ................ 20 Inches .................. 20 Inches ................. 20 Inches
Width ...................16 Inches ................ 16 Inches .................. 16 Inches ................. 16 Inches
Height ..................66 Inches ................ 66 Inches .................. 66 Inches ................. 66 Inches
Height from Floor.....66 Inches ................ 66 Inches .................. 66 Inches ................. 66 Inches
Table Tilt to Right .....45 Degrees ............. 45 Degrees ............... 45 Degrees .............. 45 Degrees
Table Tilt to Left .......10 Degrees ............. 10 Degrees ............... 10 Degrees .............. 10 Degrees
Miter Gauge Groove
Width ...................3/4-Inch ................... 3/4-Inch ....................3/4-Inch .................... 3/4-Inch
Depth ...................3/8-Inch ................... 3/8-Inch ....................3/8-Inch .................... 3/8-Inch
Miter Gauge.............Standard.................. Standard ................... Standard .................. Standard
Blade Dimension
Standard ..............3/8x0.025x92.5 In.... 3/8x0.025x92.5 In. .... 3/8x0.025x92.5 In. ... 3/8x0.025x92.5 In.
Download from Www.Somanuals.com. All Manuals Search And Download.
- Misuse of this machine can cause serious injury.
- For safety, machine must be set up, used and
serviced properly.
- Always follow instructions in Operating Instruc-
tions and Parts Manual when changing acces-
sory tools or parts.
- Read, understand and follow instructions in the
Operating Instructions and Parts Manual which
was shipped with your machine.
- Never modify the machine without consulting
Wilton Corporation.
You - the Stationary Power Tool User - Hold
the Key to Safety.
When Setting up Machine:
- Always avoid using machine in damp or poorly
lighted work areas.
- Always be sure the machine support is se-
curely anchored to the floor or the work bench.
When Using Machine:
- Always wear safety glasses with side shields
(See ANSI Z87.1)
- Never wear loose clothing or jewelry.
- Never overreach - you may slip and fall.
When Servicing Machine:
Read and follow these simple rules for best results
and full benefits from your machine. Used properly,
Wilton’s machinery is among the best in design and
safety. However, any machine used improperly can
be rendered inefficient and unsafe. It is absolutely
mandatory that those who use our products be
properly trained in how to use them correctly. They
should read and understand the Operating Instruc-
tions and Parts Manual as well as all labels affixed to
the machine. Failure to follow all of these warnings
can cause serious injuries.
- Always disconnect the machine from its electri-
cal supply while servicing.
Machinery General Safety Warnings
Whenever changing accessories or general
1. Always wear protective eye wear when operat-
ing machinery. Eye wear shall be impact
resistant, protective safety glasses with side
shields which comply with ANSI Z87.1
specifications. Use of eye wear which does
not comply with ANSI Z87.1 specifications
could result in severe injury from breakage of
eye protection.
2. Wear proper apparel. No loose clothing or
jewelry which can get caught in moving parts.
Rubber soled footwear is recommended for
best footing.
3. Do not overreach. Failure to maintain proper
working position can cause you to fall into the
machine or cause your clothing to get caught
pulling you into the machine.
4. Keep guards in place and in proper working
order. Do not operate the machine with guards
removed.
maintenance is done on the machine, electri-
cal power to the machine must be discon-
nected before work is done.
9. Maintain all machine tools with care. Follow
all maintenance instructions for lubricating and
the changing of accessories. No attempt shall
be made to modify or have makeshift repairs
done to the machine. This not only voids the
warranty but also renders the machine unsafe.
10. Machinery must be anchored to the floor.
11. Secure work. Use clamps or a vise to hold
work, when practical. It is safer than using
your hands and it frees both hands to operate
the machine.
5
12. Never brush away chips while the machine is
in operation.
13. Keep work area clean. Cluttered areas invite
accidents.
14. Remove adjusting keys and wrenches before
turning machine on.
5. Avoid dangerous working environments. Do
not use stationary machine tools in wet or
damp locations. Keep work areas clean and
well lit.
6. Avoid accidental starts by being sure the start
switch is OFF before plugging in machine.
7. Never leave the machine running while unat-
tended. Machine shall be shut off whenever it
is not in operation.
15. Use the right tool. Don’t force a tool or attach-
ment to do a job it was not designed for.
16. Use only recommended accessories and follow
manufacturers instructions pertaining to them.
17. Keep hands in sight and clear of all moving
parts and cutting surfaces.
18. All visitors should be kept at a safe distance from
the work area. Make the workshop completely
8. Disconnect electrical power before servicing.
Download from Www.Somanuals.com. All Manuals Search And Download.
safe by using padlocks, master switches, or by
removing starter keys.
19. Know the tool you are using — its application,
limitations, and potential hazards.
General Electrical Cautions
This saw should be grounded in accordance
with the National Electrical Code and local codes
and ordinances. This work should be done by a
qualified electrician. The saw should be grounded
to protect the user from electrical shock.
Caution: For circuits which are far away from the
electrical service box, the wire size must be in-
creased in order to deliver ample voltage to the
motor. To minimize power losses and to prevent
motor overheating and burnout, the use of wire sizes
for branch circuits or electrical extension cords
according to the following table is recommended.
Wire Sizes
Conductor Length
AWG (American Wire Gauge) Number
240 Volt Lines
No. 14
120 Volt Lines
No. 14
0 - 50 Feet
50 - 100 Feet
Over 100 Feet
No. 14
No. 12
No. 12
No. 8
Safety Instructions on Sawing Systems
1. Always wear leather gloves when handling saw
blade. The operator shall not wear gloves when
operating the machine.
2. All doors shall be closed, all panels replaced,
andother safety guards in place prior to the
machine being started or operated.
8. Bring adjustable saw guides and guards as
close as possible to the workpiece.
9. Always wear protective eye wear when
operating, servicing, or adjusting machinery.
Eyewear shall be impact resistant, protective
safety glasses with side shields complying with
ANSI Z87.1 specifications. Use of eye wear
which does not comply with ANSI Z87.1
specifications could result in severe injury
from breakage of eye protection.
3. Be sure that the blade is not in contact with the
workpiece when the motor is started. The
motor
allow the saw to
shall be started and you should
come up to full speed
before bringing the saw
with the workpiece.
4. Keep hands away from the blade area. See
Figure A.
blade into contact
See Figure B
10. Nonslip footwear and safety shoes are recom-
mended. See Figure C.
11. Wear ear protectors (plugs or muffs) during
extended periods of operation. See Figure D.
12. The workpiece, or part being sawed, must be
securely clamped before the saw blade enters
the workpiece.
13. Remove cut off pieces carefully, keeping
hands away from saw blade.
14. Saw must be stopped and electrical supply cut
off or machine unplugged before reaching into
cutting area.
6
5. Remove any cut off piece carefully while
keeping your hands free of the blade area.
6. Saw must be stopped and electrical supply
must be cut off before any blade replacement
or adjustment of blade support mechanism is
done, or before any attempt is made to change
the drive belts or before any periodic service or
maintenance is performed on the saw.
7. Remove loose items and unnecessary
workpieces from area before starting machine.
15. Avoid contact with coolant, especially guarding
your eyes.
A
B
D
C
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Setup and Operation
This manual includes operating and maintenance
instructions for the Wilton 14-Inch Tradesman
Vertical Band Saws, Models 8201, 8203, 8201VS,
and 8203VS. This manual also includes parts
listings and illustrations of replaceable parts.
Set-up
The band saw is shipped with the saw frame
separated from the saw base. Set-up of the band
saw involves installing the frame and setting-up the
saw on the shop floor.
Band Saw Features
Refer to Figures 1 through 3 for key features of the
band saw machine. Refer to the Specifications
section for additional information on the features
and capabilities of the saw.
Assembly of Band Saw
The saw is shipped as two separate units — saw
frame and base. The saw frame must, therefore,
be assembled to the base.
1. Remove loose parts from the saw base and
sawframe.
2. Place the base in the location in the shop and
bolt the base to the floor. (See following
section on spotting saw.) Put shims under the
hold-down bolts as required to make sure the
saw is level.
3. Place the saw frame on the base. Be sure the
pulleys on the saw frame and pulleys in the
base are aligned with each other.
4. Install the four bolts, upper washers, lower
washers, lock washers and nuts that secure
the frame to the base finger tight. Using a
straight edge, align the pulleys. Then tighten
the four attachment bolt and nuts.
5. Loosen the motor mounting bolts and install
the drive belt(s).
Blade tension adjustment
knob
Upper drive
7
wheel
Figure 1: Band Saw Features (Rear View)
(Models 8201/8203)
Upper
blade
guide
support
assembly
Lock Knob
Saw Head
Upper blade
guide and
support
Upper
Clutch Knob
ON/OFF
switch
assembly
Table
Optional rip
fence
wheel
guard
Miter
slot
Gearbox
Blade guard
Lower wheel guard
Dust chute
Oil Level
Gauge
Variable Speed
Control
Lower drive
wheel
Lower blade
guide and
support
Pivoting
Motor
Mounting
Plate
Drive
Motor
assembly
Base
Motor Pulley
Figure 3: Band Saw Features (Front View)
(All Models)
Figure 2: Band Saw Features (Rear View)
(Models 8201VS/8203VS)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Tension the belts (refer to Changing Drive Belt
Position).
the saw before attempting electrical connec-
tions.
7. Check gearbox fluid level in sight gauge. If
required, add lubricant to bring level halfway up
the sight gauge. (Two containers of Shell
Spirax 90 HD gear oil are packed with the saw.
The containers have sufficient amount of
lubricant to fill the gearbox.)
8. Check blade tension and support mechanism
adjustment (refer to Changing Saw Blades).
9. Plug the motor cable into the switch box on the
saw frame. For 3-phase motors, follow the
instructions in the Electrical section to com-
plete the electrical hookup.
2. Connect the green or green-with-white-trace
wire to the branch circuit ground wire.
3. Connect the remaining three wires to the
power wires in the 3-phase branch circuit.
4. Reestablish power in the electrical branch.
5. Turn on power to the saw motor using the
switch.
6. Observe the direction of the blade. It should
be going DOWNWARD, into the slot on the
table. If it is not going downward, the power
wires are hooked-up incorrectly.
7. To correct hook-up, disconnect and lock out
power to the branch, again. Reverse any two
of the power wires on the hook-up to the saw
cable.
8. Reestablish power in the branch and turn the
saw on again. The blade should now be going
downward into the table slot.
NOTE: Observe all electrical codes. Local codes
or difficult environmental conditions may de-
mand special electrical hook-ups. Always use a
licensed electrician for any special electrical
hook-up.
Setting-up Saw
Note: local electrical codes or other codes may
require direct connection to a covered, protected
junction box, or other electrical hook-up method.
Especially under difficult industrial conditions,
specialized electrical connections may be
necessary. For special electrical hook-ups, a
licensed electrician should be used to connect
the saw to power.
The saw should be bolted securely to the shop
floor to make sure the saw is stable when sawing
long, heavy or unwieldy work pieces. Always use
extra support for long or heavy stock.
There are lugs in the bottom of the saw base for
use in bolting down of the saw. After positioning
the saw, open the door in the base and mark the
positions of the four lug holes. Move the saw to
expose the marks. Prepare for attachment as
required by the attachment method being used.
Install the applicalbe fasteners. Install shims as
required to level the saw. Tighten the fastners to
secure the saw to the floor.
CAUTION: KNOW AND OBSERVE ALL LOCAL
AND OTHER APPROPRIATE ELECTRICAL
CODES WHEN ATTACHING THIS BAND SAW
TO YOUR POWER SUPPLY.
8
Switch
1-ph.
Motor
power
Plug
source
Electrical
Models 8201 and 8201VS are delivered with a 115
volt single phase motor. Models 8203 and 8203VS
are delivered with a 220/440 volt, 3-phase motor.
Green or green
with white trace
Ground lug
Switch
When the saw is a 115 volt model, it is supplied
with a standard 115 volt plug and power cord which
can be plugged into any suitable branch circuit.
3-ph.
power
source
Motor
Plug
When the saw is equipped with a 3-phase motor
there will be no plug on the 4-wire cable to the saw
switch box. Instead, follow these instructions to
connect the 3-phase motor to the power source:
Green or green
with white trace
Ground lug
Connecting to 3-phase power
Figure 4: Wiring Diagrams
1. Disconnect and lock out the branch circuit to
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Optional Frame Riser
are checked and adjusted as required.
18. Install the extension plug cable between the
motor plug and switch plug.
19. Plug the electrical cord into the power
source or close the circuit breaker on the
branch circuit. Operate the band saw to
verify blade tracking.
NOTE: Refer to the illustrations in the Replacement
Parts section for location of the parts used on
the frame riser.
1. Remove the saw blade (refer to Changing Saw
Blades).
2. Remove the two screws at the top and bottom
of the blade guide that holds the blade guide on
the frame.
Installing Optional Rip Fence
The rip fence slides on two rails attached at the
front and rear of the work table. Install the fence
mechanism as follows:
WARNING: The saw must be turned off and
power disconnected any time the rubber
protectors are being changed.
NOTE: Refer to the illustrations in the Replace-
ment Parts section for location of the parts
used on the rip fence.
3. Unplug the electrical cord or open the circuit
breaker in the branch circuit.
4. Support the upper frame and wheel assembly
with a strap attached to an overhead crane.
Use additional straps to be sure the frame
assembly will be held in a stable position when
it is lifted off the lower frame assembly.
5. Remove the nut on the bolt that clamps the
upper frame to the lower frame and remove the
bolt, two washers and nut.
6. Lift the upper frame high enough off of the
lower frame to clear the riser casting.
7. Be certain the mating surfaces of the lower
frame, riser, and upper frame are all clean and
free from dirt and debris.
1. Slide the rails into the fence.
2. Ease the fence and rails into position on the
table.
3. Using the four spacers and four attachment
bolts, attach the rails securely to the saw
table.
4. The fence can now be adjusted and used
according the instructions in Adjustment and
Use of Optional Rip Fence.
8. Position the riser casting over the lower frame.
Make sure the locating dowels are inserted in
the mating holes in the riser casting.
9. Lower the upper frame onto the riser casting.
Make sure the locating dowels fit into their
mating holes.
9
10. Put the new (longer) attaching bolt and top
washer through the upper frame and riser, into
the lower frame.
11. Put a washer and nut on the bolt and tighten
securely.
12. Attach the bracket hooks to the top and bottom
of the blade guard using self-tapping screws.
13. Attach the blade guide using the screws that
held the original (shorter) guard.
14. Remove the old (shorter) blade guide post
assembly from the upper frame.
15. The guide support assembly with the carbide
guides and blade support bearings should be
transferred to the new, longer support rod.
Several other new parts are included for this
component. (Refer to the parts illustrations for
more detail.)
16. Install a new 105-inch blade (refer to Changing
a Blade). Make sure blade tension and tracking
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6 provides suggested blade speeds for
various
Operating Instructions
types of materials. The recommended speeds
should be decreased 30 to 50% when using
carbon steel blades. (The chart provides speeds
that are based on cutting a 4-inch thick work piece
using a bi-metal blade without cutting fluid.)
Operating Controls
START/STOP Switch
The following conditions should also be consid-
ered:
The START/STOP switch (refer to Figure 5) is
used to turn on the band saw drive motor. The
START switch has a molded guard which prevent
inadvertent pressing of the START pushbutton.
1. Increase speed 15% for materials 1/4-inch
thick, 12% for 3/4-inch thick, 10% for 1 1/4-
inch thick, and 5% for 2 1/2-inch thick.
2. Decrease speed 12% when cutting 8-inch thick
material.
START/STOP Switch
To avoid tooth breakage, select a blade-tooth pitch
that will have two or more teeth in contact with the
workpiece at all times.
Guarded START
Switch
Different blade materials and tooth geometry (pitch
and set) permit sawing a wide range of common
and exotic materials. Contact your industrial
distributor for recommendations on specialized
blades. Using the corrrect blade can save you
time, trouble, and the possibility of dulling and
pemature discarding of the blade you normally
might use. NOTE: Always use a sharp blade.
SHARP BLADES ARE CHEAP INSURANCE
AGAINST POOR CUTTING EFFICIENCY AND
ACCELERATED MACHINE WEAR.
E-Stop
Figure 5. START/STOP Controls
The STOP pushbutton is not guarded to allow use
as an E-stop in an emergency.
Variable Speed Control
The variable speed control (refer to Figure 9) is
used to change the speed of the saw blade. Refer
to Adjusting Blade Speed for additional informa-
tion on the use of the variable speed control.
Material being cut
Speed (SF/M) range
Structural steel shapes
Low carbon steel
Medium carbon steel
High carbon steel
Cr-moly steel
Ni-Cr-moly steel
Chromium steel
Cr-vanadium steel
Tool steel
Stainless steel
Free machining steel
Cast iron
Copper alloy (CU-Zm)
Bronze
Al-bronze
Monel
165
10
160-165
115
Operating Instructions
Saw blades
90-100
105-135
90-115
80-140
105-115
40-80
40-70
80-100
55-90
55
The Wilton 14-inch saws accept blades from 1/8-
inch wide to 3/4-inch wide. The narrower widths
are used for cutting shapes or circles; the wider
widths are used for straight cuts.
For straight cuts, use the widest available saw
blade. A wide blade provides cutting stability, and
allows for more accurate and straighter cuts.
Blade speed effects the efficiency of the cut and
the service life of the blade. Good shop practice
requires that work-hardening materials, such as
stainless steel, require the cut be completed in a
single pass. Otherwise, the effect of stopping the
cut can result in hardening of the cut interface.
90
40
40-45
25-40
3000
Titanium alloy
Aluminum (soft)
Aluminum (T-6+)
Carbon
3000
3000
Slate
80-160
3000
PTFE sheet, rod, rounds
Hard rubber
3000
Plywood
Other woods
3000
3000
Other materials such as wood require higher blade
speeds to prevent fiber tearing. The chart in
Figure 6. Blade Speed to Material Chart
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Adjusting Blade Support/Guide Height
The upper blade support and guide mechanism
can be adjusted to accomodate the height of the
work piece.
1. To adjust the support, loosen the knob that
clamps the support rod, then move the support
up or down in its holder. (Refer to Figure
location of the support mechanism.
2. Adjust the support so there is space between
the support and work piece. Space of approxi-
mately 1/8-inch is generally appropriate.
Adjusting Blade Tension
Blade tension is set by a spring loaded tension
mechanism on the upper drive wheel. Check the
level of the tension device before cutting. The
tension for various blade widths as indicated on the
casting on the tension device.
Figure 8. Table Tilt Mechanism andAngle Gauge
Adjusting TableAngle
(Refer to Figure 8.) The angle gauge is under the
front of the table. The angle gauge shows the
angle of the table relative to the saw blade. The
table is mounted on trunnions that allow
adjustment downward 45 degrees, and upward 10
degrees. Loosen the two trunnion lock knobs
slightly to adjust the table angle and retighten the
lock knobs.
NOTE: by adjusting the positive leveling stop on
the table leveling mechanism, it is possible to tilt
the table upward 10 degrees. When returning
to 0 degrees, the table leveling mechanism
must be reset after completing the sawing
operation (refer to Machine Set-up).
11
WARNING: When cutting at an angle with a
tilted table, provide a guide against which
the material being cut can rest. Cutting
“freehand” at an angle, can result in injury
and maintaining an accurate cut is it diffi-
cult.
Leveling Work Table
The table can be adjusted to level the table relative
to the saw bleade. Use the following method:
WARNING: The saw must be turned off and
power disconnected any time the gearbox
lubricant is being drained or filled.
1. Unplug the electrical cord or open the circuit
Figure 7. Saw Blade Tension and Tracking Mechanism
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Measure from both ends of the miter slot to the
straight edge.3. If the measurements are
breaker in the branch circuit.
2. Move the upper blade guide assembly to the
very top of its travel.
3. Make sure the blade is straight, and fully
tensioned. (A damaged or worn blade may
provide a poor reference surface for squaring
the table.)
not equal at both ends of the slot, loosen six
bolts securing the table to the table trunnions
(see Figures 12 and 13.)
4. Adjust the table until it is parallel with the blade.
5. Tighten the trunnion attaching bolts.
4. Loosen the table lock knobs and hold the
table firmly against its positive leveling stop.
6. Using a machinist’s square, check to make
sure the table is 90 degrees to the blade.
USING LEATHER PROTECTIVE GLOVES,
turn the upper drive wheel to check the
squareness at a minimum of three points on
the blade
Adjusting Blade Speed
(Models 8201/8203)
Figure 6 on page 9 provides blade speeds for
various materials. To adjust the blade speed,
change the clutch position of the clutch (in or out)
and the position of the drive belt on the pulleys on
the motor and reduction gearbox shafts.
7. If the table is not level, unlock the lock nut on
the table leveling bolt.
Adjusting Blade Speed
(Models 8201VS/8203VS)
8. Turn the leveling bolt as required to make the
table square to the blade.
9. Lock the leveling bolt lock nut and recheck the
table level. When the table is level...
10. Lock the table lock knobs securely and
recheck for level. Adjust as necessary until
the table is level while everything is tightened
to working tightness.
See Figure 9 at bottom of this page.
1. The blade speed is controlled by an adjust-
ment
mechanism on the right end of the
saw. Speed increases or decreases as the
knob is turned
2. A placard on the drive belt guard (shown
below) provides recommended speeds for
various materials.
3. A speed indicator is provided on the barrel of
the adjustment mechanism. In surface feet per
minute; Position 0 = 334, 1 = 262, 2 = 216, 3 =
171, 4 = 137, and 5 = 116.
11. With everything locked down, look at the
pointer for the angle gauge. It should be
exactly on the zero mark of the gauge (Figure
12). If not, loosen the pointer screw, adjust the
pointer until it is on zero, then tighten the
pointer screw while holding the pointer se-
curely in position on zero.
4. Turn the speed adjustment knob to the desired
setting as determined by the material being
cut.
Adjusting Miter Gauge Slot Parallelism
12
The miter slot should be parallel to the side of the
blade. If the saw is not cutting straight when using
the miter gauge, the miter slot may not be parallel.
1. Put a straight edge against the blade. Make
sure to position the blade so tooth offset does
not affect the straight edge.
Changing Clutch Position
WARNING: NEVER attempt to shift the clutch
mechanism while the saw is running. The
saw must be turned off before clutch shifted.
Speed
Indicator
Variable
Speed
Control
Top View
Front View
Figure 9. Variable Speed Control
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Release the weight of motor so the motor
pivots downward. The weight of the motor is
provide adequate belt tension.
6. Plug the electrical cord into the power source
or close the circuit breaker on the branch
circuit.
1. Turn the main switch to off.
2. Pull the door open on the pulley case.
3. Turn the clutch handle clockwise and push in,
to engage the high speed pulley drive. Or, turn
the clutch handle clockwise, and pull out, to
engage the reduction gearbox drive.
Changing Pulley-to-Belt Position
NOTE: When pushing or pulling the clutch knob,
the dogs on the clutch mechanism are being
engaged. Take the time make sure the clutch
handle is all the way in, or all the way out, so the
clutch dogs are in full engagement when the saw
is started.
WARNING: NEVER attempt to change pulley
shaft positions while the saw is running.
The saw must be turned off and power
disconnected any time pulley shaft poistions
are being changed.
4. Close the pulley case door.
5. Plug the electrical cord into the power source or
close the circuit breaker on the branch circuit.
1. Unplug the electrical cord or open the circuit
breaker in the branch circuit.
2. Open the door on the machine base and the
door on the pulley case.
Changing Drive Belt Position
3. Push up on the motor to pivot the motor
upward and slacken the drive belt.
4. With the motor drive belt loose, remove both
pulley drive belts.
WARNING: The saw must be turned off and
power disconnected before changing drive
belt positions.
5. Both of the pulleys are secured to their shafts
with two set screws. These are located in the
bottoms of the V-grooves on the pulleys.
Using a hex wrench, loosen (but do not
remove) all four set screws.
Refer to Figure 9, below.
1. Unplug the electrical cord or open the circuit
breaker in the branch circuit.
2. Open the door on the machine base and the
door on the pulley case.
6. Pull the pulleys straight off each shaft.
7. Put the lower pulley on the upper shaft and the
upper pulley on the lower shaft.
3. Push up on the motor to pivot the motor
upward and slacken the drive belt.
4. Move the drive belt to the desired pulley
position.
NOTE: Never force the belts to change pulley
location without pivoting the motor to loosen the
motor belt. Failure to do so can cause damage
to the drive mechanism, and accelerate belt
wear and possibly result in belt failure.
8. Push the upper pulley firmly against the
reduction gearbox and tighten the two set
screws which secure it to the shaft.
9. Using a straight edge against the pulley
flanges, make certain the bottom pulley is
aligned with the upper pulley. Then tighten the
two set screws that secure the lower pulley to
the shaft.
13
Figure 10. Clutch to Pulley Speed Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Install the belts as required (refer to Figure 10).
11. Release the weight of motor so the motor
pivots downward. The weight of the motor will
provide adequate belt tension.
Maintenance
This section contains periodic maintenance
12. The weight of the motor should provide
sufficient tension so the the middle of the small
drive belt is displaced approximately the
thickness of the belt. (The high speed belt is
adjusted at the same time as the smaller belt.)
13. Set the drive clutch to the desired position (IN
or OUT).
recommendations and maintenance procedures.
Changing Saw Blade
WARNING: The saw must be turned off and
power disconnected any time saw blades
are being changed.
14. Close the access doors.
15. Plug the electrical cord into the power source
or close the circuit breaker on the branch
circuit.
1. Unplug the electrical cord or open the circuit
breaker in the branch circuit.
2. Pull open both upper and lower drive wheel
guards (refer to Figure 1).
Using Miter System
3. Release blade tension completely by turning
the tension handle fully counterclockwise.
4. Remove table leveling pin. The pin has a tight
push fit in its slot; it is not threaded. (Refer to
Figure 13.
5. Use a screwdriver to pop out the table insert.
6. Loosen the set screws that lock the guide
blocks. Move the guide blocks outward. Then
turn the micro-adjusting knob to move the
blade support bearing to the very rear of its
travel.
7. Using a hex wrench, loosen the set screw that
locks the lower blade guide and support
assembly. Move the assembly to the very rear
of its travel by using the micro-adjusting knob
on the back side of the assembly (refer to
Figure 11).
A miter gauge is provided with the band saw. The
miter gauge slips into a slot in the face of the work
table. The miter gauge can be adjusted from 0 to
45 degrees.
Adjust the miter gauge as follows:
1. Loosen the clamping screw on the miter
gauge.
2. Adjust to desired angle.
3. Tighten the clamping screw.
Using Rip Fence
1. Unlock the fence by loosening the lock knob
(ref. 7) and handle (ref. 10.)
2. Slide the fence on its guides until it is the
required distance from the blade.
14
Blade support
bearing
Support
bearing
microadjusting
knob
3. Tighten the lock knob and handle, slightly.
4. Using a machinist’s square, measure the
distance between the edge of the miter slot
and both the front and rear of the rip fence.
Adjust so both distances are equal.
5. Check the fence-to-blade gap, again. Read-
just the fence, if necessary, until the blade gap
is correct and the fence is parallel with the
miter slot.
Blade
Guide block
set screws
6. Tighten the fence firmly using the lock knob
and handle.
Guide block
support
microadjusting
knob
Using the Dust Control Chute
Carbide guide blocks
On the lower side of the table, below the cutting
position of the blade, is a plastic tube which can be
attached to a shop vacuum, or to a shop dust
control system. The dust control chute can be seen
in several of the figures used to illustrate the
operation of the saw.
Figure 11. Upper Blade Guides
8. Using a hex wrench, loosen the carbide blade
guide set screws. Open up a reasonably large
gap between the guides; do this on both the
upper and lower blade guides.
Download from Www.Somanuals.com. All Manuals Search And Download.
9. USING LEATHER GLOVESANDANSI Z87.1
EYEWEAR TO PROTECT YOURSELF FROM
THE CUTTING BLADE, carefully remove the
blade from the drive wheels. Remove the
blade out of the saw table through the table.
10. Hang the removed blade in a safe place.
Leveling
bolt lock
nut
Table leveling
bolt
Trunnion
attachment
bolts
Blade
support
bearing
NOTE: Clean out the interior of the saw with a
shop vacuum. Examine the bearings and other
exposed mechanisms of the saw.
Blade support
bearing micro-
adjusting knob
Front
trunnion
lock
Carbide
blade guide
11. Using protective gloves, carefully ease the
replacement blade into the table slot and over
the upper and lower drive wheels.
Blade guide
microadjusting
knob
Guide
knob
block
Rear
support
trunnion
lock
NOTE: It is possible to install the blade upside
down. Make sure the teeth on the blade are
pointing downward.
NOTE: The blade should be “free standing” at the
cutting throat; the upper and lower blade guides
should not touch the blade at any point. Also,
make sure the blade is in the slot in the blade
guard on the left side of the machine frame.
Refer to Figure 1 to identify the blade guard.
knob
Figure 12. Lower Blade Guide Support
Rear View
Table leveling
pin
Lower blade
support bearing
Front trunnion
Trunnion
attachment
bolt
12. Apply tension to the blade using the tension
knob. The tension levels for various blade
widths are shown on the markings on the
tension device. Refer to Figure 3 for a view of
the tension system.
rear
trunnion
13. Slowly turn the upper drive wheel by hand,
while OBSERVING THE BLADE TRACKING.
The blade should track, more or less, in the
center of the drive wheel. If the blade does not
track true, adjust the tracking to keep the blade
centered.
14. Unlock the tilt adjustment knob by loosening
its locking wing nut. Both the adjustment knob
and wing nut are identified in Figure 7.
15. Turn the tilt adjustment knob (usually a VERY
LITTLE at a time) to adjust the tilt of the upper
drive wheel. Do this while turning the upper
wheel by hand, and adjusting until the blade
stays centered on the wheel.
Rear trunnion
lock knob
Guide block
microadjusting
knob
15
Front
trunnion
Carbide guide block
lock knob
Figure 13. Lower Blade Guide Supports
Front View
19. Adjust the upper support assembly so the
support bearing just contacts the back edge of
the saw blade.
16. Tighten the tilt mechanism locking wing nut.
17. Using the micro-adjusting knob, move the
lower blade support assembly (Refer to Figure
12) forward until the support bearing just
contacts the back edge of the saw blade.
18. Adjust the lower carbide blade guides until they
just contact the sides of the blade. Make sure
the guides DO NOT CONTACT THE TOOTH
PORTION OF THE BLADE. The guides
should touch only the flat part of the blade.
After correctly positioning the carbide guide
blocks, tighten the set screws securely.
20. Adjust the upper carbide blade guides until they
just make contact with the blade BEHIND THE
TOOTH AREA OF THE BLADE. Then tighten
the set screws securely.
21. Replace the table insert.
22. Insert the table pin into its slot.
23. Close the drive wheel guards.
24. Plug the electrical cord into power source or
close the circuit breaker on the branch circuit.
25. Turn on the power and observe the action of
the blade to sure the blade is correctly ad-
justed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Draining and refilling the reduction
gearbox.
Blade
Blade support bearing
WARNING: The saw must be turned off and
power disconnected any time the gearbox
lubricant is being drained or filled.
Guide block
set screws
Support
bearing
shaft
1. Unplug the electrical cord or open the circuit
breaker in the branch circuit.
2. Open the door in the base.
3. Push up on the motor to loosen the drive belts.
4. Remove the pipe plug at the bottom of the
gearbox. Drain the oil into a suitable container
for safe and appropriate disposal.
5. Replace the drain plug.
6. Open the filler plug.
7. Add lubricant until the level is halfway up the
sight gauge window (refer to Figure 15). Use
Shell Spirax HD 90 gear lubricant.
8. Replace the filler plug.
Carbide guide block
Guide block
support set
screw
9. Replace the drive belts. Allow the motor to
pivot downward to apply tension to the belts.
10. Close the access door.
11. Plug the electrical cord into the power source
or close the circuit breaker on the branch
circuit.
Figure 14. Lower Blade Support Assembly
Replacing drive wheel rubber
protectors
The rubber rings that cover the drive wheels are
called protectors. The protectors protect the wheel
from blade damage and provide a high friction
drive force on the tensioned blade. Over a long
period of service, the protectors wear and may
require replacement.
WARNING: The saw must be turned off and
power disconnected any time the rubber
protectors are being changed.
16
1. Unplug the electrical cord or open the circuit
breaker in the branch circuit.
Oil Level Gauge
Gear Box Pulley
2. Remove the blade according to the step-by-
step instructions on blade replacement.
3. Remove the rubber protectors from the drive
wheels. Use a flat screwdriver blade or knife
blade to loosen the protectors, being careful
not to nick or score the aluminum drive
wheels.
4. Clean the surface of the drive wheels. Use a
solvent such as mineral spirits as required to
achieve a clean, dry surface for the new
protectors.
Figure 15. Gearbox Oil Level Gauge
Periodic Maintenance
Refer to the Periodic Maintenance chart for mainte-
nance that should be performed at various time
intervals.
5. Carefully slip the replacement protectors onto
the drive wheels.
6. Replace the saw blade and return the saw to
service by following the steps in Changing
Saw Blades.
Troubleshooting
Refer to the Troubleshooting charts for equipment
fault, probable cause and suggested remedy.
7. Plug the electrical cord into the power source or
close the circuit breaker on the branch circuit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Periodic Maintenance
Maintenance
Item
Action
Interval
Replace blade when teeth are
broken
Replace blade when bent — or worn
— Use a wider blade for more
accurate straight cuts
Saw blade
Listen for sound of
missing teeth
Observe cutting
action for cleanness
and accuracy
Whenever
operating saw
Whenever
operating saw
Listen for a poor weld
— a “click” as it
passes through the
guide blocks
When changing
blade
Use a different blade or dress the
weld with a grinder.
Watch for signs of
slippage on the drive
wheels (blade occa-
sionally slows or
comes to a stop while
sawing)
Be sure you are using the correct
blade tension — Check drive wheel
rubber strips for cleanliness and
adherence to drive wheel — replace if
necessary
Whenever
sawing
Lower drive
wheel
Check bearing area
for leakage of lubri-
cant
Check bearing area
for leakage of lubri-
cant
Monthly
Monthly
Replace bearing if leakage occurs
Upper drive
wheel
Replace bearing if leakage occurs
Wipe or brush clean
Daily and when
changing blade
Drive wheel
rubber protec-
tors
Check for cleanliness
Drive belts
Check for smooth
surfaces and adher-
ence to drive wheel
surface
Clean when necessary — replace if
damaged or excessively worn
Monthly or when
blade slippage
occurs
17
Replace a glazed belt — DO NOT USE
BELT DRESSING
Check for glazing
Monthly, or when
slippage occurs
(squealing belt)
Reduction
gearbox
Check sight glass for
level — should be to
halfway point on sight
glass
Fill up to half-way point on sight glass
with Shell Spirax HD 90
Daily
Drain and refill with Shell Spirax
HD 90
Annually
Blade support Check for wear,
Replace when necessary
Monthly and when
changing blade
bearings
damage or lubricant
leakage
Carbide blade Check for excessive
guides
wear
Replace if excessively worn
When changing
blade
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Probable cause
Suggested remedy
Fault
1. Material loose in vise.
2. Incorrect speed or feed.
1. Clamp work securely.
2. Refer to Figure 6 or check
Machinist’s Handbook for speed/
feed appropriate for the material
being cut.
Excessive blade
breakage
3. Teeth too coarse for material.
4. Incorrect blade tension.
3. Check Machinist’s Handbook for
recommended blade type.
4. Adjust blade tension to the point
where the blade just does not slip
on the wheel.
5. Saw blade contacts workpiece
before the saw is started.
5. Start the motor before placing the
saw on the workpiece.
6. Blade rubs on the wheel flange.
7. Misaligned guides.
6. Adjust blade tracking.
7. Adjust guides.
8. Cracking at weld.
8. Longer annealing cycle.
1. Blade teeth too coarse.
2. Blade speed too high.
1. Use a finer tooth blade.
2. Try a lower blade speed.
Premature blade
dulling
3. Hard spots in workpiece or scale 3. Increase feed pressure (hard
on/in workpiece.
spots). Reduce speed, increase
feed pressure (scale).
4. Work hardening of material
(especially stainless steel).
5. Insufficient blade tension.
6. Operating saw without pressure
on workpiece.
4. Increase feed pressure by reduc-
ing spring tension.
5. Increase tension to proper level.
6. Do not run blade at idle in/on
material.
1. Feed pressure too fast.
2. Guide bearings not adjusted
properly.
3. Inadequate blade tension.
4. Dull blade.
1. Decrease pressure.
Bad cuts
(out-of-square)
18
2. Adjust guide bearing clearance to
0.001 inch (0.002 inch maximum).
3. Gradually increase blade tension.
4. Replace blade.
5. Incorrect blade speed.
5. Check blade speed
(see Figure 6).
6. Blade guide assembly is loose.
7. Blade guide bearing assembly
loose.
6. Tighten blade guide assembly.
7. Tighten blade guide bearing
assembly.
8. Blade track too far away from
wheel flanges.
8. Adjust blade tracking.
9. Guide bearing worn.
9. Replace worn bearing.
1. Blade speed too high for feed
pressure.
1. Reduce blade speed and feed
pressure.
Bad cuts (rough)
2. Blade is too coarse.
2. Replace with finer blade.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
(Continued)
Blade is twisting
1. Blade is binding in the cut.
2. Blade tension too high.
1. Decrease feed pressure.
2. Decrease tension on blade
Unusual wear on
side/back of blade
1. Blade guides worn
2. Blade guide bearings not
adjusted.
1. Replace blade guides.
2. Adjust blade guide bearings.
3. Blade guide bearing bracket is
loose.
3. Tighten blade guide bearing
bracket.
Teeth missing/
ripped from blade
1. Blade tooth pitch too coarse for
workpiece.
1. Use blade with finer tooth pitch.
2. Feed too slow; feed too fast.
2. Increase feed pressure and/or
blade speed.
3. Workpiece vibrating.
4. Gullets loading up with chips.
3. Clamp workpiece securely.
4a. Use blade with a coarse tooth
pitch—reduce feed pressure.
4b. Brush blade to remove chips.
Motor running too
hot
1. Blade tension too high.
2. Drive belt tension too high.
3. Blade too coarse for workpiece
4. Blade too fine for workpiece
5. Speed reducer requires lubrica-
tion.
1. Reduce tension on blade.
2. Reduce tension on drive belt.
3. Use blade with fine tooth pitch.
4. Use blade with coarse tooth pitch.
5. Check speed reducer.
Excessive speed
reducer noise/
vibration
1. V-belt is too tight.
1. Reset V-belt tension.
19
Replacement Parts
This section provides exploded view illustrations that show the replacement parts for the Wilton Model
8201, 8203, 8201VS, and 8203VS Vertical Band Saws. Also provided are parts listings that provide part
number and description. The numbers shown on the illustration relate to the item number in the facing
parts listing.
Order replacement parts from:
WMH Tool Group
2420 Vantage Drive
Elgin, IL 60123
Phone: 847-274-6848
Identify the replacement part by the part number shown in the parts listing. Be sure to include the model
number and serial number of your machine when ordering replacement parts to assure that you will
receive the correct part.
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View and Parts Listing – Base –
Models 8201, 8203, 8201VS and 8203VS
Ref Part.
No. Number Description
Ref Part.
20
Qty
1
1
1
1
No. Number Description
18 5513847 Nut (M5)
19 5513848 Nut (M8)
20 5513849 Bolt, Carriage (M8x16)
21 5784331 Bolt, Hex Head (M6x12) 1
22 5513851 Bolt, Hex Head (M8x25) 4
23 5782761 Bolt, Pan Head (M5x12) 6
Qty
4
8
1
2
3
4
5
5513834 Base
5513835 Door
5513836 Lock (Ref. Note 1)
5513837 Washer (Ref. Note 1)
5513838 Bolt, Pan Head (M4x5)
(Ref. Note 1)
4
2
6
8
5513839 Pad
2
1
24 5513853 Washer, Flat (M5x• 10)
25 5513854 Washer, Flat (M6x• 16)
26 5513855 Washer, Flat (M8x• 18) 12
27 5513856 Washer, Spring (M8)
28 5513857 Nut, Nylon (M8)
29 5513858 Lock Assembly
30 5513859 Key
31 5513860 Stand, Close
(Not Shown)
8
1
5784391 Motor - 115V 1-ph
5784411 Motor - 220/460V 3-ph
5784421 Cord, Motor - 1-ph
5784431 Cord, Motor - 3-ph
9
1
8
2
1
1
1
10 5513842 Strain Relief
11 5784281 Plate, Strain Relief
12 5513844 Case, Pulley
5513845 Cover, Pulley Case
(Not Shown)
2
1
1
1
32 5513861 Bracket, Motor
33* 5507565 Base Assembly
without motor
1
1
13 5513846 Knob
1
Note 1: Noted parts are part of lock assembly, number 29
* Ref No. 33 includes all components shown in the Exploded View except the motor (Ref No. 8).
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View – Saw Head – Models 8201, 8203, 8201VS, and 8203VS
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Listing – Saw Head – Models 8201, 8203, 8201VS, and 8203VS
Ref Part.
Ref Part.
Ref Part.
No. Number Description
Qty
1
No. Number Description
Qty
2
No. Number Description
Qty
2
1
2
3
4
5
6
7
5782511 Upper Arm, Frame
5782521 Bracket, Upper Wheel Sliding
5782531 Hinge, Upper Wheel Shaft
5782541 Pin, Pivot
41 5782961 Screw, Pan Head (M5x0.8x25)
42 5782971 Strain Relief (6W3-4R)
78 5783361 Screw, Micro Adjustment
(M8x1x40)
1
1
1
43 5782981 Cord, Power (110Volt, 1 phase) 1
5513899 Cord, Power (220 Volt, 3 phase)
79 5783371 Nut, Micro Adjustment
80 5783381 Screw, Hex Head (M6x1x10)
81 5783391 Blade Guide, Carbide
82 5783411 Bracket, Support
83 5783421 Guard, Upper Wheel Blade
84 5783431 Washer, Flat (M6x16)
85 5783441 Screw, Hex Head (M6x1x10)
86 5783451 Table
1
4
2
1
1
2
1
1
1
1
2
2
2
1
6
1
2
2
1
1
1
2
2
1
1
2
2
2
5782551 Shaft, Upper Wheel
5782561 Pin, Roll (4x16)
1
44 5782991 Cord, Power (Switch to Motor -
110 Volt, 1 phase)
1
1
5782571 Knob, Blade Track Adjustment
(M8x55)
5782581 Nut, Wing (M8x1.25)
5782591 Knob, Blade Tension Adjstmnt
1
5513900 Cord, Power (Switch to Motor -
220 Volt, 3 phase)
8
9
1
1
1
1
1
3
2
1
2
2
2
1
1
45 5783011 Bushing, Power Cord
46 5783021 Clip, Wire
1
1
1
1
2
1
1
4
1
1
2
1
10 5782611 Spring, Tension
11 5782621 Nut, Square
47 5783031 Screw, Hex Head (M6x1x55)
48 5783041 Base
87 5783461 Pin, Roll (3x8)
88 5783471 Insert, Table
89 5783481 Pin, Table
12 5782631 Guard, Upper Wheel (Inner)
13 5782641 Screw, Pan Head (M5x0l8x6)
14 5782651 Washer, Flat (M5x10)
15 5782661 Wheel, Upper
16 5782671 Bearing (6202Z)
17 5782681 Ring, Retaining (R-35)
18 5782691 Protector, Wheel
19 5782711 Nut, Hex (M12)
20 5782722 Blade, Saw, Metal Cutting
(92.5 x 0.025 x 14R)
49 5783051 Bolt, Hex Head (M16x2x55)
50 5783061 Washer, Flat (M16x40)
51 5783071 Nut, Hex (M16)
52 5783081 Hinge (Lower)
53 5783091 Screw, Flat Head (M5x10)
54 5783111 Guard, Lower Wheel
55 5783121 Chute, Dust
90 5783491 Shoe, Trunnion Clamp
91 5783511 Bolt, Hex Head (M10x50)
92 5783521 Trunnion
93 5783531 Scale
94 5783541 Screw, Hex Head (M6x12)
95 5783551 Screw, Hex Head (M8x80)
96 5783561 Screw, Hex Head (M6x30)
97 5783571 Washer, Lock (M8)
98 5783581 Nut (M8x1.25)
99 5783591 Support, Bracket Trunnion
100 5783611 Pointer
56 5783131 Screw, Pan Head (M6x1x8)
57 5783141 Bolt, Hex Head (Left Hand)
(M8x1.25x15)
58 5783151 Washer, Flat
59 5783161 Wheel, Lower
60 5783171 Bearing (6204Z)
61 5783181 Shaft, Lower Wheel
(Metal Cutting Saw)
5783191 Shaft, Lower Wheel
(Wood Cutting Saw)
62 5783211 Key (5x5x20)
63 5783221 Bolt, Hex Head (M8x1.25x40)
64 5783231 Washer, Flat (M8x18)
65 - - - -
66 - - - -
67 5783241 Pin, Dowel
68 5783251 Ball, Steel (8 mm)
69 5783261 Spring
70 5783271 Screw, Set (M10x1.5x10)
71 5783281 Knob (M10x1.4x30)
72 5783291 Screw, Pan Head (M6x1x12)
73 5783311 Bearing (6200ZZ)
74 5783321 Sleeve, Upper Spacing
75 5783331 Screw, Set (M6x1x10)
76 5783341 Post, Upper Support Bracket
77 5783351 Post, Guide
1
1
2
1
1
5782732 Blade, Saw, Wood Cutting
(92.5 x 0.025 x 6H)
1
21 5782741 Bolt, Fixed
2
2
101 5783621 Knob (M10x1.5)
102 5783631 Post, Lower Support Bracket
102 5783641 Block, Adjusting
104 5783651 Plate, Guide
105 5783661 Screw, Flat Head Socket
(M6x1x15)
106 5783671 Sleeve, Spacing
107 - - - -
22 5782751 Catch
23 5782761 Screw, Pan Head (M5x0.8x12) 2
24 5782771 Bracket
2
2
4
1
25 5782781 Bolt, Hex Head (M8x1.25x16)
26 5782791 Lock, Male
4
27 5782811 Screw, Self Tapping (M4x0.7x8) 2
4
2
28 5782821 Stud
1
2
2
4
- - - - - -
- - -
4
29 5782831 Guard, Blade
30 5782841 Retainer
- - - - - -
- - - - - -
- - -
- - -
1
108 5783681 Bushing, Setting
109 5783691 Screw, Set (M5x0.8x5)
110 5783711 Bar, Adjusting
111 5783721 Handle
1
31 5782851 Screw, Self Tapping (M3.5x12) 1
2
32 5782861 Hinge, Upper
12
1
1
33 5782871 Screw, Pan Head (M5x0.8x8) 12
1
112 - - - -
- - - - - -
- - -
2
34 5782881 Nut, Flange (M5x 0.8)
35 5782891 Guard, Upper Wheel (Outer)
36 5782911 Washer, Spring (M8)
37 5782921 Knob (M8x1.25)
1
1
2
1
2
1
113 5783731 Bar, Adjusting
114 5783741 Washer, Spring (M8)
115 5783751 Nut, Flange (M8)
116 5783761 Washer
2
2
1
2
1
2
38 5782931 Bracket, Switch
7
117 5783771 Spacer
1
39 5782941 Screw, Self Tapping (M4x.7x10) 1
1
40 5782951 Switch
2
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View – Gearbox – Models 8201 and 8203
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Listing – Gearbox – Models 8201 and 8203
Ref Part.
No. Number Description
Ref Part.
Ref Part.
Qty
1
1
3
1
2
1
1
1
1
1
1
1
No. Number Description
15 5783961 Key (5x5x18)
16 5783971 Bushing/Spacer
17 5783981 Gear
18 5783991 Shaft (with gear)
19 5784011 Key (5x5x40)
20 5513824 Pin, Parallel (5x20)
21 5784031 Key (7x7x20)
22 5784041 Ring, Retaining (S30)
23 5784051 Seal, Oil
Qty
1
1
1
1
1
2
2
3
1
2
2
1
1
1
No. Number Description
29 5784121 Bushing
30 5513800 Cover, Bearing
31 5784141 Cover, Bearing
32 5784151 Cover, Bearing
33 5784161 Screw, Pan Head
(M5x0.8x8)
Qty
1
1
1
1
1
2
3
4
5
6
7
8
9
5783831 Housing Gearbox
5629151 Bearing (6206ZZ)
9100441 Bearing (6200ZZ)
5783851 Bearing (6303ZZ)
5783861 Plug
5783871 Seal, Oil (30x7)
5783881 Seal, Oil (17x40x7)
5783891 Plug, Drain (1/8x28PT)
5783901 Plug (3/8x19PT)
9
34 5784171 Screw, Pan Head
(M6x1x10)
8
35 5784181 Pulley, Gear Box
36 5784191 Screw, Set (M6x1x10)
37 5784211 V-Belt (A50)
38 5784221 V-Belt (A35)
39 5784231 Pin, Roll (4x16)
40 5518281 Oil, Gear Box 500cc (not
shown)
1
2
1
1
1
1
10 5783911 Glass, Oil Level
11 5783921 Gear
12 5783931 Bearing (3206)
13 5783941 Ring, Internal Snap (R62) 1
14 5783951 Shaft (with gear)
24 5784061 Dog, Clutch
25 5784071 Pin, Roll (5x30)
26 5784081 Shaft, Clutch
27 5784091 Knob
1
28 5784111 Pulley
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View – Gearbox – Models 8201VS and 8203VS
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Listing – Gearbox – Models 8201VS and 8203VS
Ref Part.
Ref Part.
Ref Part.
No. Number Description
Qty
1
1
2
1
1
1
1
2
1
1
2
1
1
1
1
2
1
1
No. Number Description
19 5783951 Shaft, Gear (M)
20 5783871 Cover, Oil Seal (30x7)
21 5784141 Cover, Bearing (M)
22 5783991 Shaft, Gear (I)
23 5783881 Seal, Oil (17x40x7)
24 5784151 Cover, Bearing (I)
25 5513814 Speed Changer,
Non-Step (Set)
Qty
1
1
1
1
1
1
1
No. Number Description
34 5629151 Bearing (6206ZZ)
35 5783961 Key (5x5x18)
36 5784011 Key (5x5x40)
37 5784031 Key (7x7x20)
38 5513824 Pin, Parallel (5x20)
39 5784071 Pin, Spring (5x30)
40 5783941 Ring, Retaining (R62)
41 5784041 Ring, Stop (S30)
42 5513828 Bolt, Countersunk Head
(M5x10)
Qty
1
1
1
1
2
2
1
3
1
2
3
4
5
6
7
8
9
5513790 Housing Gearbox
5513791 Packing
5783861 Plug
5783911 Gauge, Oil Level
5513794 Shaft, Lower Wheel
5513795 O-Ring (P15)
5513796 O-ring (P24)
5513797 Block, Clutch
5513798 Gear (O)
26 5513815 Belt, Synchronous
(V-Type)
27 5513816 V-Belt (A51)
1
3
10 5783971 Spacer
11 5513800 Cover, Bearing (O)
12 5513801 Pulley
1
43 5784161 Screw, Pan Head (M5x8) 9
28 - - - -
29 - - - -
30 - - - -
- - - - - -
- - - - - -
- - - - - -
- - -
- - -
- - -
3
1
1
13 5784121 Bushing
44 5513830 Bolt, Pan Head (M6x16)
45 5513831 Bolt, Hex Head Socket
(M8x12)
46 5513832 Screw, Set (M6x10)
47 5513833 Plug, Oil
8
1
14 5784051 Seal, Oil (12x22x7)
15 5513804 Rod, Clutch
16 5513805 O-Ring (P9)
17 5784091 Knob (M10)
18 5513807 Gear, Helical (M)
31 9100441 Bearing (6200ZZ)
32 5783851 Bearing (6203ZZ)
33 5783931 Bearing (3206ZZ)
2
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List – Optional Riser Block – All Models
27
Ref Part.
No. Number Description
Qty
1
1
2
4
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
3
4
5
6
7
8
9
5784511 Block, Riser
5784521 Guard, Blade
5784531 Hook, Bracket
5784541 Screw, Self Tapping
5784551 Screw, Hex Head (M16x2x200)
5784561 Washer (M16)
5784571 Nut (M16)
5784581 Post, Guide
5784591 Guard, Upper Wheel Blade
10 5784611 Extender, Blade Guard
11 5784621 Bolt, Carriage (M8x15)
12 5784631 Washer (M8)
13 5782581 Nut, Wing (M8)
14 5784641 Blade, Saw (Metal Cutting)
5784681 Blade, Saw (Wood Cutting)
15 5784651 Pin, Dowel
16 5784661 Cord, Extension Power (1-Phase)
5784671 Cord, Extension Power (3-Phase)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List – Optional Rip Fence – All Models
28
Ref Part.
No. Number Description
Qty
2
1
1
1
4
4
1
1
1
2
3
4
5
6
7
8
9
5784811 Rail, Guide
5784821 Fence, Rip
5784831 Seat Assembly, Clamp
5784841 Clamp Rail
5784851 Plug (7/8)
5784861 Spacer
5784871 Knob
5784881 Bar, Adjusting
5784891 Nut (3/8x16UNC)
1
10 5784911 Handle
1
11 5784921 Screw, Socket Head Cap
(M8x30)
4
12 5784931 Screw, Hex Head (M6x12)
13 5782981 Washer (M6)
5784941 Gauge Assembly, Miter
(Not Shown)
2
2
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
WMH Tool Group
2420 Vantage Drive
Elgin, IL 60123
Phone: 847-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|