This Manual is Bookmarked
Operating Instructions and Parts Manual
16-Inch Woodworking Band Saw
Model JWBS-16B
WMH TOOL GROUP, Inc.
2420 Vantage Drive
Elgin, Illinois 60124
Ph.: 800-274-6848
Part No. M-708749B
Revision A 03/08
Copyright © 2008 WMH Tool Group, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service....................................................................................................................................2
Table of Contents..........................................................................................................................................3
Warning.........................................................................................................................................................4
Introduction ...................................................................................................................................................6
Specifications................................................................................................................................................6
Grounding Instructions..................................................................................................................................7
Unpacking .....................................................................................................................................................8
Contents of Shipping Container ................................................................................................................8
Assembly and Setup .....................................................................................................................................9
Base Support Extension............................................................................................................................9
Adjusting Blade Tension..........................................................................................................................10
Adjusting Blade Tracking.........................................................................................................................10
Lower Blade Guide Adjustment...............................................................................................................11
Mounting the Table..................................................................................................................................12
Rail Assembly (optional accessory) ........................................................................................................13
Fence Assembly and Adjustment (optional accessory) ..........................................................................13
Resaw Guide (optional accessory)..........................................................................................................14
Miter Gauge (optional accessory) ...........................................................................................................14
Tilting the Table.......................................................................................................................................15
Height Scale Adjustment.........................................................................................................................15
Changing Blades .....................................................................................................................................16
Replacing V-Belt......................................................................................................................................17
Adjusting Belt Tension.............................................................................................................................17
Electrical Connections.............................................................................................................................18
Maintenance............................................................................................................................................18
Upper Blade Guide Adjustment...............................................................................................................10
Troubleshooting ..........................................................................................................................................19
Parts............................................................................................................................................................19
Replacement Parts..................................................................................................................................19
Upper Wheel Assembly...........................................................................................................................20
Lower Wheel and Motor Assembly..........................................................................................................22
Blade Guides Assembly ..........................................................................................................................24
Table Assembly.......................................................................................................................................26
Fence & Miter Assembly (optional accessory)........................................................................................28
Wiring Diagram ...........................................................................................................................................30
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
1. Read and understand the entire owner's manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This band saw is designed and intended for use by properly trained and experienced personnel only.
If you are not familiar with the proper and safe operation of a band saw, do not use until proper
training and knowledge have been obtained.
5. Do not use this band saw for other than its intended use. If used for other purposes, WMH Tool
Group disclaims any real or implied warranty and holds itself harmless from any injury that may result
from that use.
6. Always wear approved safety glasses/face shields while using this band saw. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this band saw, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
blahblahblah
20. Make your workshop child proof with padlocks, master switches or by removing starter keys.
21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
22. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other
moving parts. Do not overreach or use excessive force to perform any machine operation.
23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
24. Use recommended accessories; improper accessories may be hazardous.
25. Maintain tools with care. Keep blades sharp and clean for the best and safest performance. Follow
instructions for lubricating and changing accessories.
26. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do
not use your hands.
27. Do not stand on the machine. Serious injury could occur if the machine tips over.
28. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
29. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or
possibly even death.
- - SAVE THESE INSTRUCTIONS - -
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual is provided by Jet covering the safe operation and maintenance procedures for model
JWBS-16B Band Saw. This manual contains instructions on installation, safety precautions, general
operating procedures, maintenance instructions and parts breakdown. This machine has been designed
and constructed to provide years of trouble free operation if used in accordance with instructions set forth
in this manual. If there are any questions or comments, please contact either your local supplier or WMH
Specifications
Stock Number ...................................................................................................................................708749B
Cutting Capacity (height)............................................................................................................................10”
Cutting Capacity ( width)............................................................................................................................16”
Maximum Rip Left of Blade w/Fence ...................................................................................................14-1/4”
Blade Length............................................................................................................................................123”
Blade Speed.................................................................................................................................3000 SFPM
Minimum Blade Width ...............................................................................................................................1/8”
Maximum Blade Width ...........................................................................................................................1-1/2”
Table Size .........................................................................................................................................17” x 17”
Table Tilt......................................................................................................................................45°R to 10°L
Table Height from Floor .............................................................................................................................35”
Wheel Diameter ...................................................................................................................................16-5/8”
Dust Chute Diameter....................................................................................................................................4”
Overall Dimensions......................................................................................... 68" H x 31-1/2" W x 26-3/8" D
Motor ........................................................................................................................................ 1-1/2 HP, 1Ph
..............................................................................................................................115/230V, prewired 115V
Net Weight (approx.).......................................................................................................................... 317 lbs.
Shipping Weight (approx.).................................................................................................................. 340 lbs.
The specifications in this manual are given as general information and are not binding. The WMH Tool
Group reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Canada. The green colored grounding ear, lug,
or tab, extending from the adapter, must be
connected to a permanent ground such as a
properly grounded outlet box, as shown in
C, Fig. 1.
Grounding Instructions
This machine must be
grounded while in use to protect the operator
from electric shock.
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric
shock. This machine is equipped with an electric
cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged
into a matching outlet that is properly installed
and grounded in accordance with all local codes
and ordinances.
Figure 1
230 Volt Operation
Do not modify the plug provided. If it will not fit
the outlet, have the proper outlet installed by a
qualified electrician.
To convert the JWBS-16B from 120V to 230V,
single phase operation, the following is strongly
recommended:
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. The conductor, with insulation
having an outer surface that is green with or
without yellow stripes, is the equipment-
grounding conductor. If repair or replacement of
the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a
live terminal.
Contact your local Authorized JET Service
Center or qualified electrician for proper
procedures to install the plug. The band saw
must comply with all local and national codes
after the 230V plug is installed.
The 115V attachment plug supplied with the
band saw (C, Fig. 2) must be replaced with a
UL/CSA listed plug suitable for 230V operation
(D, Fig. 2).
Check with a qualified electrician or service
personnel if the grounding instructions are not
completely understood, or if in doubt as to
whether the tool is properly grounded. Use only
three wire extension cords that have three-prong
grounding plugs and three-pole receptacles that
accept the tool’s plug.
The band saw with a 230V plug should only be
connected to an outlet having the same
configuration (D, Fig. 2). No adapter is available
or should be used with the 230V plug.
Important: In all cases (115 or 230 volts), make
certain the receptacle in question is properly
grounded. If you are not sure, have a registered
electrician check the receptacle.
Repair or replace a damaged or worn cord
immediately.
Model JWBS-16B
Model JWBS-16B Band Saw has a 1-3/4 HP 1
phase motor and is wired from the factory for
115 volt operation, but can be rewired for 220
volts.
115 Volt Operation
The JWBS-16B Band Saw comes equipped with
a plug that looks like A, Fig. 1. and is used in an
outlet that looks like B, Fig. 1. A temporary
adapter with a grounding ear secured with a
screw (C, Fig. 1) may be used to connect this
plug to a two-pole receptacle if a properly
grounded outlet is not available. The temporary
adapter should only be used until a properly
grounded outlet can be installed by a qualified
electrician. This adapter is not applicable in
Figure 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Remove the packing material from the band saw.
Note: Remove the plywood and bolts from the
base. Inspect the machine for damage. Report any
damage to your distributor and shipping agent.
Move the saw to its permanent working location.
The site should be dry, well lit, and have enough
room to handle long stock and the service and/or
adjustment of the machine from any side.
Move the band saw off the skid. Clean all rust
protected surfaces with a mild solvent or diesel fuel
and a soft cloth. Do not use lacquer thinner, paint
thinner, or gasoline. These will damage painted
surfaces.
Contents of Shipping Container
1 - Band Saw
1 - Table
1 - Owner’s Manual
1 - Warranty Card
1 - Accessory Package Contains:
2 - Extension Straps
1 - Extension Base
Accessory Packeg Include
2 - Knobs
1 - 5mm Hex Wrench
1 - 4mm Hex Wrench
1 - Handle
1 - 10/12mm Wrench
1 - 12/14mm Wrench
1 - Trunnion Support Bracket
4 - Hex Cap Bolts 5/16”-18x1-1/2”
4 - Lock Washers 5/16”
8 - 5/16-18 x 3/8 Button Hd. Cap Screws
8 - 5/16 Flat Washers
Tools Included for Assembly
1 - 10/12mm Open End Wrench
1 - 12/14mm Open End Wrench
1 - 5mm Hex Wrench
Tools Required for Assembly & Adjustments
1 - Combination Square
1 - Cross Point Screw Driver
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly and Setup
Base Support Extension
1. Attach straps (A, Fig. 1A) to extension base (B,
Fig. 1A) with (2) 5/16-18 button head cap
screws (C, Fig. 1A) and with (2) 5/16 flat
washers (D, Fig. 1A). If needed punch holes
through striping decal. NOTE: Leave screws
slightly loose.
2. Repeat for opposite end of extension base.
Figure 1A
3. Insert straps through slits in base of machine
lining up holes in machine base with tapped
holes in strap (Fig 1B)
4. Attach straps to machine base using (2) 5/16-
18 button head Cap screw (E, Fig. 1C) and (2)
5/16 flat washers (F, Fig. 1C).
5. Repeat for opposite end of extension base.
6. Tighten all (8) button head cap screws with the
5 MM hex wrench provided.
Figure 1B
7. Attach the handle (C, Fig. 2) to the hand wheel
(D, Fig. 2).
Figure 1C
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Blade Tension
1. Disconnect machine from the power source,
unplug.
2. Turn blade tension hand wheel (E, Fig. 2)
counter-clockwise to tension blade, and
clockwise to loosen the tension. A gauge on
the upper wheel slide bracket (F, Fig. 2)
indicates the approximate tension according to
the width of the blade. The JWBS-16B comes
with a 3/4” blade so the tension should be set
at 3/4” when using this blade.
As you become familiar with the saw, you may find
it necessary to change the blade tension from the
initial setting. Changes in blade width, and the type
of material being cut will have an effect on blade
tension.
Figure 2
Keep in mind that too little, or too much blade
tension can cause blade breakage and/or poor
cutting performance.
Upper Blade Guide Adjustment
Disconnect machine from the
power source, unplug before making any
adjustments! Blade teeth are sharp! Use care
when working near the saw blade. Failure to
comply may cause serious injury!
Adjusting Blade Tracking
Disconnect machine from the
power source! Never adjust blade tracking with
the machine running! Failure to comply may
cause serious injury!
1. Blade tension and tracking must be properly
adjusted prior to blade guide setup.
2. The blade guard has been removed in Figure 3
for photo purposes only.
Note: Blade tracking has been adjusted at the
factory. If, however, it is determined that blade
tracking needs adjustment:
3. Loosen the socket head cap screw (A, Fig. 3)
and position the blade guide assembly
(B, Fig. 3) so that the guides rest just behind
the gullet of the blade teeth. Tighten the socket
head cap screw.
1. Blade must be properly tensioned before
adjusting blade tracking. Make sure upper and,
lower blade guides do not interfere with the
blade while adjusting the tracking.
4. Loosen lock nuts (D, Fig. 3).
5. Adjust guide knobs (E, Fig. 3) so guides
(C, Fig. 3) rest lightly against the blade. Do not
force the guides against the side of the blade.
Tighten both lock nuts.
2. Open the upper wheel door. Rotate the wheel
forward, and observe the position of the blade
on the wheel.
The blade should rest in
approximately the center of the wheel.
6. Adjust the blade support bearing so that it is
0.003” away from the back of the blade, about
the thickness of a piece of paper. To make this
adjustment loosen wing nut (F, Fig. 3) and slide
the bearing and bearing post into position.
Tighten wing nut.
3. If adjustment is necessary, loosen the wing nut
(G, Fig. 2) at the top rear of the saw.
4. Adjust tracking by turning the knob (H, Fig. 2)
in 1/4 turn increments. Rotate the wheel
forward, and observe the position of the blade
on the wheel. Rotating knob (H, Fig. 2)
counter-clockwise should move the blade
towards the front of the wheel. Rotating the
knob clockwise should move the blade towards
the back of the wheel.
Note: Blade support bearing should be adjusted so
that the back edge of the blade overlaps the front
face of the ball bearing by approximately 1/8”. If
adjustment is needed loosen wing nut (F, Fig. 3)
and turn the bearing shaft. Tighten wing nut.
5. Continue with adjustments until the blade is
tracking properly.
6. Tighten the wing nut (G, Fig. 2).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Lower Blade Guide Adjustment
Disconnect machine from the
power source, unplug before making any
adjustments! Blade teeth are sharp! Use care when
working near the saw blade. Failure to comply may
cause serious injury!
1. Blade tension and tracking must be properly
adjusted prior to blade guide setup.
Figure 3
2. The blade guard has been removed in Figure 4
for photo purposes only.
3. Loosen the socket head cap screws (G, Fig. 4)
and position the blade guide assembly (H, Fig.
4) so that the guides rest just behind the gullet
of the blade teeth. Tighten the socket head
cap screws.
4. Loosen thumb screw (I, Fig. 4). Adjust guides
(J, Fig. 4) so they rest lightly against the blade.
Do not force the guide against the side of the
blade. Tighten thumb screw.
5. Adjust the blade support bearing so that it is
0.003” away from the back of the blade, about
the thickness of a piece of paper. To make this
adjustment loosen wing nut (K, Fig. 4) and slide
the bearing and bearing post into position.
Tighten wing nut.
Note: Blade support bearing should be adjusted so
that the back edge of the blade overlaps the front
face of the ball bearing by approximately 1/8”. If
adjustment is needed loosen wing nut (K, Fig. 4)
and turn the bearing shaft. Tighten wing nut.
Figure 4
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Table
1. Mount the trunnion support bracket (A, Fig. 5)
to the bandsaw with four 5/16” x 1-1/2” hex cap
bolts, and four 5/16” lock washers (B, Fig. 5).
2. Remove the round table insert (C, Fig. 5) found
where the blade goes through the table. Also,
remove the table pin (D, Fig. 5) found on the
side of the table.
3. Slide saw blade through slot in table where the
table pin was located. Rotate the table 90
degrees so that the miter slot is parallel to the
blade, and to the right of the blade when facing
the bandsaw.
Figure 5
4. Line up the trunnions so that the bolts feed
through the trunnion support bracket. Secure
the table with two lock knobs (C, Fig. 6).
Reinstall the table insert and table pin.
5. Place a square (E, Fig. 5) on the table and
against the back edge of the blade. If the table
needs adjusted, on the low side, loosen two
bolts (B, Fig. 5) and turn the setscrew (F, Fig.
5) until the table is approximately square to the
back edge of the blade.
Adjusting 90 Degree Table Stop
1. Blade tension and tracking must be properly
adjusted prior to table stop setup.
2. Loosen lock knobs (C, Fig. 6) and tilt table until
it rests against table stop bolt (D, Fig. 6).
Tighten knobs.
Figure 6
3. Use a square (G, Fig. 7) placed on the table
and against the blade to see if the table is 90
degrees to the blade.
4. If an adjustment is necessary, loosen the lock
knobs. Tilt the table until it is square to the
blade, and tighten the lock knobs.
5. Loosen lock nut (E, Fig. 6) and turn table stop
bolt (D, Fig. 6) until it contacts the table.
Tighten the nut (E, Fig. 6) to hold table stop in
place. When tightening the nut hold the table
stop bolt in place with a wrench to prevent
movement.
6. If necessary, adjust pointer (F, Fig. 6) to zero.
Figure 7
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rail Assembly (optional accessory)
1. Attach the front rail (A, Fig. 8) to the cast iron
table with two 1/4” x 5/8” hex cap bolts, two
1/4” lock washers, and two 1/4” flat washers.
Bolts should be in approximately the center of
the slot. Hand tighten only at this time.
2. Attach the rear rail (B, Fig. 8) to the table with
two 1/4” x 5/8” hex cap bolts, two 1/4” lock
washers, and two 1/4” flat washers. Bolts
should be in approximately the center of the
slot. Hand tighten only at this time.
Figure 8
3. Push the front, and rear rails up as far as they
will go.
4. Tighten the four hex cap bolts holding the front,
and rear rails to the table. Do not over tighten
the bolts.
5. Attach the guide tube (C, Fig. 8) to the front rail
with five 1/4” x 5/8” hex cap bolts, five 1/4” lock
washers, and five 1/4” flat washers. Bolts
should be in approximately the center of the
slot.
Figure 9
Fence Assembly and Adjustment
(optional accessory)
1. Attach the fence (D, Fig. 9) to the fence body
(E, Fig. 9) with four 5/16” x 3/4” hex cap bolts,
four 5/16” lock washers, and four 5/16” flat
washers.
2. Thread a hex nut (G, Fig. 10) onto the pad’s
threaded stud (H, Fig. 10) and insert through
the fence and rear hook (I, Fig. 10). Secure in
place using a hex nut, lock washer and flat
washer (J, Fig. 10).
Note: The hook should be adjusted so that it
overlaps the rear rail by approximately 1/8”.
3. Place fence assembly onto the guide tube.
The rear hook should engage the rear rail.
Figure 10
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Check the clearance between the table and the
fence. The gap should be the same at the front
of the table as it is at the rear. If the gap width
is different, adjust the foot at the rear of the
fence until the gap width is the same, Figure
11.
Note: You can also adjust the front rail, or rear rail
up, or down to achieve the proper clearance.
5. With a square verify the fence face is
perpendicular to the table top. If it is not the
front rail will need to be adjusted parallel to the
table top.
This can be accomplished by
measuring from the top of the table to the top of
the front rail. The measurement should be the
same at both ends of the table.
Figure 11
6. Move the fence assembly so that it aligns
parallel to the blade, and lock the fence by
pushing the lock handle down.
7. Loosen the four hex cap bolts that hold the
fence, to the fence body, and align the fence to
the blade. Tighten the four hex cap bolts.
8. Check to see that the pointer (F, Fig. 9) is
aligned with the zero marking on the guide rail.
If adjustment is necessary loosen the screw
that holds the pointer in place and line up to the
zero mark. Tighten the screw.
Note: If you cannot get the pointer lined up with the
zero mark you can slide the guide tube and front
rail left, or right to achieve the proper setting.
Resaw Guide (optional accessory)
Figure 12
For resawing attach the post (A, Fig. 12) to fence
with the lock knob (B, Fig. 12). There is a slotted
hole in the fence that will accommodate the resaw
kit. Position the post so that it is centered with the
front edge of the blade. The resaw guide will give
you a taller, single point contact surface during
resawing.
Miter Gauge (optional accessory)
1. Place the miter gauge in the table slot.
2. With a square verify the miter gauge face is
square to the blade.
3. If the miter gauge is not square to the blade
loosen the lock knob (C, Fig. 12) and adjust to
the proper setting. Tighten the lock knob.
4. If the pointer is not at 90 degrees, loosen the
screw (D, Fig. 12) holding the pointer and move
the pointer to 90 degrees.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Tilting the Table
1. Disconnect the machine from the power
source, unplug.
2. Loosen the lock knobs (A, Fig. 13).
3. Tilt table up to 45 degrees to the right, or up to
10 degrees to the left.
4. Tighten the lock knobs.
Figure 13
Note: Table stop bolt (B, Fig. 13) must be removed
to tilt table to the left.
Height Scale Adjustment
1. Disconnect the machine from the power
source, unplug.
2. The upper blade guide should be set about 1/8”
above the material to be cut.
3. Measure from the table top to the bottom of the
blade guides, Figure 14.
Figure 14
4. Set the indicator to this measurement on the
height scale. Grasp the end of the indicator (C,
Fig. 15) between your finger, and thumb. Move
the indicator into position.
Figure 15
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Blades
Disconnect machine from the
power source, unplug! Blade teeth are sharp!
Use care when handling the saw blade. Failure
to comply may cause serious injury!
1. Remove the table insert (A, Fig. 16), and table
pin (B, Fig. 16).
2. Lower the upper blade guide assembly about
half way by loosening the lock knob (F, Fig. 17)
and turning the hand wheel (G, Fig. 17).
3. Loosen socket head cap screw (C, Fig. 16) and
slide the blade guide assembly back as far as it
will go.
4. Open both wheel covers (D, Fig. 16).
5. Loosen blade tension by turning blade tension
hand wheel (E, Fig. 17) clockwise until it stops.
Note: You may want to wear leather work gloves
while removing and handling the blade.
6. Carefully remove blade from upper and lower
wheels. Remove the blade from between
upper, and lower blade guides. Turn blade and
direct through slot in table.
7. Make sure blade teeth point down toward table
and guide the new blade through table slot.
Place blade in upper, and lower blade guides.
Figure 16
8. Place blade in the middle of the upper and
lower wheels.
9. Tension and track blade before operating saw.
Find instructions for tensioning and tracking the
blade on page 10 under "Adjusting Blade
Tension" and "Adjusting Blade Tracking".
10. Replace table insert and table pin.
Figure 17
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing V-Belt
1. Disconnect the machine from the power
source.
2. Release blade tension by turning blade tension
hand wheel clockwise.
3. Release belt tension by loosening the two hex
cap bolts (A, Fig. 19). Raise the motor and
tighten hex cap bolts to take the tension off the
belt.
4. Open the lower wheel door and remove hex
nut, and washer (B, Fig. 20).
Figure 19
5. Remove the wheel (C, Fig. 21). If the lower
wheel does not come off easily you may need
to use a pulley puller to remove the lower
wheel.
6. Remove the old belt (D, Fig. 21) and replace
the belt.
7. Reinstall the lower wheel and tighten the hex
nut.
8. Loosen hex cap bolts and adjust the belt
tension. See “Adjusting the Belt Tension.”
9. Set the blade tension. See “Adjusting Blade
Tension” on page 10.
10. Check the blade tracking. See “Adjusting Blade
Tracking” on page 10.
Figure 20
Adjusting Belt Tension
The belt comes adjusted from the factory. If
adjustment is needed:
1. Disconnect the machine from the power
source.
2. Loosen hex cap bolts (A, Fig. 19).
3. Set the belt tension by lightly pressing down on
the motor and tightening the hex cap bolts (A,
Fig. 19).
Note: The weight of the motor should put enough
tension on the belt. You just want to push down
lightly to take up any slack.
Figure 21
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
All electrical connections must
be done by a qualified electrician! Failure to
comply may result in loss of property and/or
serious injury!
The JWBS-16B is rated at 1-1/2 HP, 1Ph,
115V/230V, prewired 115V.
The bandsaw comes with a 115V plug (A, Fig. 22).
If you switch the motor to 230V a plug needs to be
purchased for the bandsaw that matches the 230V
outlet you intend to use.
Confirm power at the site is the same as the saw
before making any electrical connections. Review
the wiring diagram on page 30.
Figure 22
Review the Grounding Instructions, 115 Volt
Operation, and 230 Volt Operation sections on
page 7.
Maintenance
Keep blade guides clean and free of build up.
Do not let saw dust build up in the upper and lower
wheel housings. Vacuum out frequently.
Connect the bandsaw to a JET dust collection
system.
Clean and grease the raising/lowering rack for the
upper blade guides if it becomes difficult to raise, or
lower.
Clean, and oil the tensioning mechanism if it
becomes difficult to adjust.
Vacuum out the motor fan cover.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Trouble
Possible Cause
1. Saw unplugged
Solution
1. Check plug connections
2. Fuse blown or circuit
breaker tripped
2. Replace fuse or reset circuit
breaker
Saw stops or will not start
3. Cord damaged
3. Replace cord
1. Stop not adjusted correctly
1. Check blade with square
and adjust stop
Does not make accurate 45° or 2. Angle pointer not set
90° cuts
2. Check blade with square
and adjust pointer
accurately
3. Miter gauge out of
adjustment
3. Adjust miter gauge
1. Fence not aligned with
blade
1. Check and adjust fence
2. Warped wood
2. Select another piece of
wood
3. Excessive feed rate
4. Incorrect blade for cut
3. Reduce feed rate
Blade wanders during cut
4. Change blade to correct
type
5. Blade tension not set
properly
5. Set blade tension according
to blade size
6. Guides not set properly
6. Review guide adjustment on
pages 8
1. Dull blade
1. Replace blade
2. Blade mounted wrong
3. Gum or pitch on blade
4. Incorrect blade for cut
2. Teeth should point down
3. Remove blade and clean
Saw makes unsatisfactory cuts
4. Change blade to correct
type
5. Gum or pitch on table
5. Clean table
1. Extension cord too light or
to long
1. Replace with adequate size
and length cord
Blade does not come up to
speed
2. Low shop voltage
2. Contact your local electric
company
1. Base on uneven floor
1. Reposition on flat, level
surface
2. Bad V-belt
2. Replace V-belt
Saw vibrates excessively
3. Motor mount is loose
3. Tighten motor mount
hardware
4. Loose hardware
4. Tighten hardware
Parts
Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call
800-274-6848 between 7:30 a.m. and 5:30 p.m. (CST), Monday through Friday. Having the Model
Number and Serial Number of your machine available when you call will allow us to serve you quickly and
accurately.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Upper Wheel Assembly
Index No. Part No.
Description
Size
Qty
1 ...............JWBS16B-101 .........Saw Body............................................................. .................................... 1
2 ...............TS-0152011 .............Carriage Bolt........................................................5/16-18x1.................... 6
3 ...............JWBS18-103............Upper Wheel Bracket........................................... .................................... 2
4 ...............TS-0680031 .............Flat Washer..........................................................5/16............................. 6
5 ...............TS-0720081 .............Lock Washer........................................................5/16............................. 6
6 ...............TS-0561021 .............Hex Nut ................................................................5/16-18........................ 6
7 ...............994542.....................Switch................................................................... .................................... 1
8 ...............JWBS18-108............Hex Cap Bolt........................................................M8x65......................... 1
9 ...............TS-0680021 .............Flat Washer..........................................................1/4............................... 4
10 .............JWBS18-110............Sliding Bracket..................................................... .................................... 1
11 .............JWBS18-111............Blade Tension Indicator ....................................... .................................... 1
12 .............JWBS18-112............Adjustment Bracket.............................................. .................................... 1
13 .............JWBS18-113............Shaft Bracket........................................................ .................................... 1
14 .............TS-1541031 .............Nylon Insert Lock Nut...........................................M8............................... 1
15 .............JWBS18-115............Spring................................................................... .................................... 1
16 .............JWBS18-116............Square Nut........................................................... .................................... 1
17 .............JWBS18-117............Pointer.................................................................. .................................... 1
18 .............JWBS18-118............Screw ...................................................................M5x8 ........................... 1
19 .............JWBS18-119............Set Block.............................................................. .................................... 1
20 .............TS-0267021 .............Set Screw.............................................................1/4-20x1/4................... 1
21 .............JWBS18-121............Bracket................................................................. .................................... 1
22 .............TS-0050021 .............Hex Cap Screw....................................................1/4-20x5/8................... 4
23 .............JWBS16-123............Blade Adjusting Screw......................................... .................................... 1
24 .............JWBS18-124............E-Ring ..................................................................E-9 .............................. 1
25 .............JWBS18-125............Hand Wheel ......................................................... .................................... 1
26 .............TS-0267041 .............Socket Set Screw.................................................1/4-20x3/8................... 3
27 .............TS-0209021 .............Socket Head Cap Screw......................................3/8-16x5/8................... 1
28 .............TS-0720091 .............Lock Washer........................................................3/8............................... 1
29 .............JWBS18-129............Upper Wheel Shaft............................................... .................................... 1
30 .............BB-6203ZZ...............Ball Bearing..........................................................6203ZZ........................ 2
31 .............JWBS18-131............Retaining Ring .....................................................R40 ............................. 2
32 .............JWBS16-132............Upper Wheel........................................................ .................................... 1
33 .............JWBS16-133............Tire....................................................................... .................................... 1
34 .............JWBS18-134............Flat Washer.......................................................... .................................... 1
35 .............JWBS18-135............Hex Nut ................................................................5/8-18UNF L.H............ 1
36 .............JWBS16B-136 .........Blade………………………..…. 3/4"W x 123”L x .026”T x 4TPI ................ 1
37 .............TS-0590061 .............Wing Nut ..............................................................5/16-18........................ 1
38 .............JWBS18-138............Lock Knob............................................................5/16............................. 1
39 .............JWBS16B-139 .........Upper Front Door................................................. .................................... 1
40 .............JWBS18-140............JET Plaque........................................................... .................................... 1
41 .............JWBS18-141............Warning Label...................................................... .................................... 1
42 .............JWBS18-142............Bolt....................................................................... .................................... 1
43 .............TS-0561011 .............Hex Nut ................................................................1/4-20.......................... 1
44 .............TS-081C022.............Pan Head Machine Screw ...................................#10-24x3/8.................. 2
45 .............JWBS18-39A ...........Door Hinge Pin..................................................... .................................... 1
46 .............JWBS18DXA-163 ....Blade Warning Label............................................ .................................... 1
47 .............TS-1550061 .............Flat Washer..........................................................M8............................... 2
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Upper Wheel Assembly
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Lower Wheel and Motor Assembly
Index No. Part No.
Description
Size
Qty
1 ...............JWBS18-201N .........Bearing Base ....................................................... .................................... 1
2 ...............JWBS20-62..............Adjusting Bolt....................................................... .................................... 4
3 ...............TS-0720091 .............Lock Washer........................................................3/8............................... 4
4 ...............TS-0060081 .............Hex Cap Screw....................................................3/8-16x1-3/4................ 4
5 ...............BB-6204ZZ...............Ball Bearing..........................................................6204ZZ........................ 1
6 ...............JWBS18-206N .........Spindle ................................................................. .................................... 1
7 ...............JWBS18-207............Key.......................................................................7x7x40 ........................ 1
8 ...............JWBS18-208N .........Spindle Pulley ...................................................... .................................... 1
9 ...............VB-B40.....................V-Belt ...................................................................B-40 ............................ 1
10 .............JWBS16-210............Lower Wheel........................................................ .................................... 1
11 .............JWBS16-133............Tire....................................................................... .................................... 1
12 .............TS-0680081 .............Flat Washer..........................................................5/8............................... 1
13 .............JWBS18-135............Hex Nut ................................................................5/8-18UNF L.H............ 1
14 .............JWBS18-214............Hex Nut ................................................................5/8-18UNF R.H........... 1
15 .............JWBS18-215............Bearing Cover...................................................... .................................... 1
16 .............TS-0720051 .............Lock Washer........................................................#10.............................. 3
17 .............TS-081C022.............Pan Head Machine Screw ...................................#10-24x3/8.................. 3
18 .............JWBS16-218............Motor.................................................................... .................................... 1
.................JWBS16-SC.............Starting Capacitor (not shown) ............................200MFD, 125VAC....... 1
.................JWBS16-RC.............Running Capacitor (not shown) ...........................16µF, 250V ................. 1
.................JWBS16-SCC ..........Starting Capacitor Cover (not shown).................. .................................... 1
.................JWBS16-RCC..........Running Capacitor Cover (not shown)................. .................................... 1
.................JWBS18-FAN...........Fan....................................................................... .................................... 1
.................JWBS18-CS.............Centrifugal Switch (not shown)............................ .................................... 1
.................JWBS16-MFC..........Motor Fan Cover (not shown) .............................. .................................... 1
19 .............JWBS18-219............Motor Bracket....................................................... .................................... 1
20 .............TS-0081031 .............Hex Cap Screw....................................................5/16-18x3/4 ................ 4
21 .............TS-0680031 .............Flat Washer..........................................................5/16............................. 4
22 .............TS-0060051 .............Hex Cap Screw....................................................3/8-16x1...................... 2
23 .............TS-0720091 .............Lock Washer........................................................3/8............................... 2
24 .............TS-0680041 .............Flat Washer..........................................................3/8............................... 2
25 .............JWBS16-225............Motor Pulley......................................................... .................................... 1
26 .............TS-0270031 .............Socket Set Screw.................................................5/16-18x3/8................. 2
27 .............JWBS16B-227 .........Lower Front Door................................................. .................................... 1
28 .............JWBS18-142............Bolt....................................................................... .................................... 1
29 .............TS-0561011 .............Hex Nut ................................................................1/4-20.......................... 1
30 .............JWBS20-2................Lock Knob............................................................ .................................... 1
31 .............TS-081F052.............Pan Head Machine Screw ...................................1/4-20x3/4................... 1
32 .............JWBS20-8W ............Dust Chute........................................................... .................................... 1
33 .............TS-0680031 .............Flat Washer..........................................................5/16............................. 2
34 .............TS-0051051 .............Hex Cap Screw....................................................5/16-18x1.................... 2
35 .............JWBS18-235............Plate..................................................................... .................................... 1
36 .............TS-081C032.............Pan Head Machine Screw ...................................#10-24x1/2.................. 2
37 .............JWBS18-237............Strain Relief Bushing ........................................... .................................... 2
38 .............TS-081C082.............Pan Head Machine Screw ...................................#10-24x1-1/2............... 2
39 .............TS-069204 ...............Flat Washer..........................................................#10.............................. 2
40 .............JWBS18-240............Brush.................................................................... .................................... 1
41 .............TS-0720051 .............Lock Washer........................................................#10.............................. 2
42 .............TS-0560071 .............Hex Nut ................................................................#10-24......................... 2
43 .............JWBS18-243............Motor Cord........................................................... .................................... 1
44 .............JWBS18-244............Power Cord.......................................................... .................................... 1
45 .............BB-6205ZZ...............Ball Bearing..........................................................6205ZZ........................ 1
46 .............JWBS16B-246 .........I.D. Label.............................................................. .................................... 1
48 .............JWBS18-39A ...........Door Hinge Pin..................................................... .................................... 2
49 .............JWBS16B-249 .........Base Support Foot............................................... .................................... 1
50 .............JWBS16B-250 .........Support Plate ....................................................... .................................... 2
51 .............TS-0255011 .............Button Head Socket Screw..................................5/16-18x3/8................. 8
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Lower Wheel and Motor Assembly
Index No. Part No.
Description
Size
Qty
52 .............TS-0680031 .............Flat Washer..........................................................5/16............................. 8
53 .............TS-0720081 .............Lock Washer........................................................5/16............................. 2
54 .............TS-0561021 .............Hex Nut ................................................................5/16-18........................ 2
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Guides Assembly
Index No. Part No.
Description
Size
Qty
1 ...............TS-0051051 .............Hex Cap Screw....................................................5/16-18x1.................... 4
2 ...............TS-0720081 .............Lock Washer........................................................5/16............................. 4
3 ...............TS-0680031 .............Flat Washer..........................................................5/16............................. 8
4 ...............JWBS18-304............Guide Bar Bracket................................................ .................................... 1
5 ...............JWBS18-305............Worm.................................................................... .................................... 1
6 ...............JWBS18-306............E-Ring ..................................................................E-8 .............................. 2
7 ...............JWBS18-307............Gear Base............................................................ .................................... 1
8 ...............JWBS18-308............Bushing ................................................................ .................................... 1
9 ...............JWBS18-309............C-Ring..................................................................S-12 ............................ 2
10 .............JWBS18-310............Shaft..................................................................... .................................... 1
11 .............JWBS18-311............Gear ..................................................................... .................................... 1
12 .............TS-0208071 .............Socket Head Cap Screw .....................................5/16-18x1-1/4.............. 2
13 .............JWBS18-313............Lock Knob............................................................5/16............................. 1
14 .............JWBS18-314............Plate..................................................................... .................................... 1
15 .............TS-0051011 .............Hex Cap Screw....................................................5/16-18x1/2................. 4
16 .............JWBS18-316............Guide Bar............................................................. .................................... 1
17 .............JWBS16B-317 .........Pointer.................................................................. .................................... 1
18 .............TS-0720071 .............Lock Washer........................................................1/4............................... 5
19 .............TS-0050011 .............Hex Cap Screw....................................................1/4-20x1/2................... 1
20 .............JWBS18-320............Guide Bracket ...................................................... .................................... 1
21 .............TS-0207021 .............Socket Head Cap Screw......................................1/4-20x1/2................. 11
22 .............JWBS18-322............Blade Guard......................................................... .................................... 1
23 .............TS-0720111 .............Lock Washer........................................................1/2............................... 1
24 .............TS-0561051 .............Hex Nut ................................................................1/2-13.......................... 1
25 .............JWBS20-110............Locking Shaft ....................................................... .................................... 1
26 .............JWBS20-115............Upper Guide Bracket ........................................... .................................... 1
27 .............JWBS20-114............Guide Wheel Assembly........................................ .................................... 2
28 .............JWBS20-113............Blade Support Shaft w/ Bearing........................... .................................... 2
29 .............JWBS18DXA-353 ....Wing Screw..........................................................1/4-20x1/2................... 4
30 .............TS-0270031 .............Socket Set Screw.................................................5/16-18x3/8................. 2
31 .............JWBS20-2................Lock Knob............................................................ .................................... 1
32 .............TS-081F052.............Pan Head Machine Screw ...................................1/4-20x3/4................... 1
33 .............JWBS18-333............Hand Wheel ......................................................... .................................... 1
34 .............TS-0267041 .............Socket Set Screw.................................................1/4-20x3/8................... 1
35 .............JWBS20-103A .........Handle.................................................................. .................................... 1
36 .............JWBS16B-336 .........Cutting Height Scale ............................................ .................................... 1
37 .............JWBS20-120............Lower Guide Bracket ........................................... .................................... 1
38 .............JWBS18-338............Lower Guide Wheel Housing ............................... .................................... 2
39 .............JWBS18-339............Lower Guide Wheel Assembly............................. .................................... 2
40 .............TS-0207031 .............Socket Head Cap Screw......................................1/4-20x5/8................... 2
41 .............TS-0680021 .............Flat Washer..........................................................1/4............................... 4
42 .............JWBS18-342............Lower Blade Guard.............................................. .................................... 1
43 .............TS-0254021 .............Button Head Socket Screw..................................1/4-20x1/2................... 2
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Guides Assembly
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Assembly
Index No. Part No.
Description
Size
Qty
1 ...............JWBS16-401............Table .................................................................... .................................... 1
2 ...............JWBS20-144............Table Insert.......................................................... .................................... 1
3 ...............JWBS20-145............Roll Pin.................................................................Ø3x10 ......................... 1
4 ...............JWBS18-448............Table Pin.............................................................. .................................... 1
5 ...............JWBS18-408N .........Trunnion Support Bracket.................................... .................................... 1
6 ...............TS-0051071 .............Hex Cap Screw....................................................5/16-18x1-1/2.............. 4
7 ...............TS-0720081 .............Lock Washer........................................................5/16............................. 4
8 ...............TS-0270061 .............Set Screw.............................................................5/16-18x5/8................. 2
9 ...............TS-0060111 .............Hex Cap Screw....................................................3/8-16x2-1/2................ 1
10 .............TS-0561031 .............Hex Nut ................................................................3/8............................... 1
11 .............TS-0720091 .............Lock Washer........................................................3/8............................... 1
12 .............JWBS18-415............Lock Knob............................................................ .................................... 2
13 .............JWBS18-446............Pointer.................................................................. .................................... 1
14 .............JWBS18-447............Screw ...................................................................M5x8 ........................... 1
15 .............TS-1491081 .............Hex Cap Screw....................................................M10x50....................... 2
16 .............JWBS18-417............Trunnion Clamp Shoe.......................................... .................................... 2
17 .............JWBS18-416............Trunnion............................................................... .................................... 2
18 .............TS-1482021 .............Hex Cap Screw....................................................M6x12......................... 6
19 .............JWBS18-420............Scale .................................................................... .................................... 1
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Assembly
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Fence & Miter Assembly (optional accessory)
Index No. Part No.
Description
Size
Qty
1 ...............JWBS18-401............Lock Knob............................................................ .................................... 1
2 ...............TS-0680021 .............Flat Washer..........................................................1/4............................. 11
3 ...............JWBS18-403............Miter Gauge Body................................................ .................................... 1
4 ...............200156.....................Guide Disc............................................................ .................................... 1
5 ...............JWBS18-405............Screw ...................................................................M6x8 ........................... 1
6 ...............JWBS18-406............Pointer.................................................................. .................................... 1
7 ...............JWBS18-407............Guide Bar............................................................. .................................... 1
10 .............TS-0720081 .............Lock Washer........................................................5/16............................. 4
22 .............JWBS18-422W ........Front Rail.............................................................. .................................... 1
23 .............TS-0050021 .............Hex Cap Screw....................................................1/4-20x5/8................... 9
24 .............TS-0720071 .............Lock Washer........................................................1/4............................. 10
25 .............JWBS18-425............Scale .................................................................... .................................... 1
26 .............JWBS18-426W ........Guide Rail ............................................................ .................................... 1
27 .............JWBS18-427W ........Rear Rail .............................................................. .................................... 1
30 .............JWBS18-430............Fence Body.......................................................... .................................... 1
31 .............JWBS18-431............Knob..................................................................... .................................... 1
32 .............JWBS18-432............Lock Handle......................................................... .................................... 1
33 .............JWBS18-433W ........Lock Plate ............................................................ .................................... 1
34 .............JWBS18-434............Pad....................................................................... .................................... 5
35 .............JWBS18-435............Pin........................................................................ .................................... 1
36 .............JWBS18-436............Pin........................................................................ .................................... 1
37 .............JWBS16-437............Fence ................................................................... .................................... 1
38 .............TS-0081031 .............Hex Cap Screw....................................................5/16-18x3/4................. 4
39 .............TS-0680031 .............Flat Washer..........................................................5/16............................. 4
40 .............TS-0810012 .............Screw ...................................................................#10-24x1/4.................. 2
41 .............TS-0733031 .............External Tooth Lock Washer................................#10.............................. 1
42 .............JWBS18-442............Pointer.................................................................. .................................... 1
43 .............TS-0561011 .............Hex Nut ................................................................1/4-20.......................... 2
44 .............JWBS18-444............Sliding Pad........................................................... .................................... 1
45 .............JWBS18-445............Rear Hook............................................................ .................................... 1
49 .............JWBS18-449............Resaw Post.......................................................... .................................... 1
50 .............JWBS18-450............Knob..................................................................... .................................... 1
51 .............JWBS18-451............JET Fence Label.................................................. .................................... 1
52 .............JWBS20-455............End Cover ............................................................ .................................... 2
.................JWBS18-MGCP.......Miter Gauge Assembly......................................... ......................................
.................JWBS16-FCP...........Fence Assembly Complete.................................. ......................................
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Fence & Miter Assembly (optional accessory)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
31
Download from Www.Somanuals.com. All Manuals Search And Download.
WMH Tool Group, Inc.
2420 Vantage Drive
Elgin, Illinois 60124
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|