FIND OUT MORE
ON THE WEB.
WILBURCURTIS.COM
WILBUR CURTIS COMPANY, INC.
Iced Tea Brewer Instructions
Important Safeguards/Conventions
MODELS INCLUDED
• TCTD-35
• TCTD-35S
• PTTD-3
• TCO-308
• TCO-417
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be
performed by an authorized Wilbur Curtis service center.
• Do NOT immerse the unit in water or any other liquid
• To reduce the risk of fire or electric shock, do NOT open top or front panel. No user serviceable parts inside.
Repair should be done only by authorized service personnel.
• Keep hands and other items away from hot parts of unit during operation.
• Never clean with scouring powders, bleach or harsh implements.
• TCO-421
Conventions
WARNING HOT LIQUID,
Scalding may occur.
Avoid splashing.
WARNINGS – To help avoid personal injury
Important Notes/Cautions – from the factory
Sanitation Requirements
CAUTION: Please use
this setup procedure
Curtis ADS System is Factory Pre-Set and Ready to Go… Right from the Carton.
Following are the Factory Settings for your Iced Tea Brewing System:
before attempting to use
this brewer. Failure to follow the
instructions can result in injury or
• Brew Temperature = 204°F
• Concentrate = 1 Gallon
System Requirements
• Dilution = 2 Gallon
the voiding of the warranty.
• Drip Mode = 30 Seconds
• Water Source: 20 – 100PSI (Min Flow Rate of 1 GPM)
• Electrical: See attached schematic for standard
CAUTION: DO NOT
connect this brewer to
hot water. The inlet valve
Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having jurisdiction.
SETUP STEPS
is not rated for hot water.
1. Place unit at counter height. on a firm, level base, in such a way that it can be connected to water and power supply.
2. Connect water line to inlet fitting on valve. Water pressure entering brewer is required to be stable and must provide
minimum of 1 gallon per minute. Use water regulator for constant pressure. Required water pressures, 20 to 100 psi.
2. Plug power cord into electrical outlet rated 20A.
3. Turn on toggle switch, behind unit. Heating tank will start filling. When the water reaches probe,heating element
turns on automatically.
4. Heating tank will require 20 to 30 minutes to attain operating temperature. READY TO BREW indicator will light at
this time.
5. Insert brewcone. Place empty tea container under brew cone. With water at operating temperature, run brew cycle,
without tea, for about 1 minute. This clears the water lines of air. Stop the brew cycle by switching off at ON/OFF
button. Discard water in tea container.
The National Sanitation Foundation requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for
cleaning underneath.
2. In some areas an approved backflow prevention device may be required between the brewer and the water supply.
WARNING TO AVOID
SCALDING, Do not
remove brewcone while
brew light is flashing.
BREWING
INSTRUCTIONS
1. Place filter in brew basket. 2. Slide brew cone into brew 3. Press the BREW button to
Pour leaf tea into basket.
rails. Place tea container
under brew cone.
brew tea.
C
ISO 9001 REGISTERED
WILBUR CURTIS COMPANY
Montebello, CA 90640
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO
WWW.WILBURCURTIS.COM
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated Parts List - TCTD-35/35S Curtis Iced Tea Brewer, Continued from page 2
ITEM PART N
º
DESCRIPTION
17
17A
18
19
20
21
22
23
23A
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
WC- 102
WC- 103
WC-1438
WC-5231
WC-5851
WC-43062
SWITCH, TOGGLE SPST 25A 125/250 VAC RESISTIVE
SWITCH, TOGGLE DPST 25A 125/250 VAC RESISTIVE
SENSOR, HEATING TANK
COMPOUND, SILICONE 5 OZ
COVER, TANK W/NOTCHES
GASKET, TANK LID
WC-5502-01 PROBE ASSY, LL W/HEX FITTING, O-RING & NUT
WC- 904
WC- 906
WC-4394
WC- 522
WC-43055
WC-29009
WC-6210
WC-54096
WC-3685
WC-5310
WC-7115
WC-7119
WC-38103
WC-3724
WC-37260
WC-1805
WC-1803
WC-3707
ELEMENT, HEATING 1.6 KW, 120V W/JAM NUTS
ELEMENT, HEATING 2 KW 220V W/JAM NUTS
SHOCK GUARD, HEATING ELMT
THERMOSTAT, HI LIMIT HEAT CNTRL DPST 277V 40A
GUARD, SHOCK RESET THERMOSTAT
FITTING, TANK INLET/DRAIN
SHIELD, BUBBLE
TANK ASSY, COMPLETE TCTD-35/S PTTD
INSULATION WRAP, PTTD/TCTD
TUBE, 5/16" ID x 1/8” W SILICONE
LID, TEA OVAL
SHELL, W/A TCO421
LABEL, FRONT
KIT, E-Z VIEW REPLACEMENT
KIT, FAUCET W/ADAPTER COMPL
SEAT CUP, FAUCET S’
FAUCET, SPB
KIT, REPAIR SPB FAUCET
Illustrated Parts List - PTTD Iced Tea Brewer
ITEM PART Nº DESCRIPTION
1
2
3
4
5
6
7
8
9
WC-3322
WC-3358
WC-39260
WC- 750
WC-2977-01
WC-5450
WC-5310
WC-2906
WC-2965
C-2407
BASKET, WIRE 6.423 DIA PTTD/TCTD, USED W/WC-3320
BREW CONE ASSY, W/WC-3320, WC-3322 & WC-3647
MEMBRANE CONTROL PANEL
CONTROL BOARD 120V 60Hz PTTD/TCTD
FITTING ASSY, SPRAYHEAD W/0-RING
COVER, TOP BREWER
TUBING, SILICONE 5/16" I.D.
SPRAYHEAD, BLUE .178” DIA ORF
SPOUT ASSY, BYPASS
10
COVER, CENTER WRAP
11 WC-8556
12 WC- 895
13 WC-5448
13A WC-85008
14 WC-3500
15 WC-6917
16 WC- 102
17 WC-5851
18 WC-2959
19 WC-29015
20 WC-54096
21 WC-5502-01
22 WC- 904
23 WC- 522
24 WC-4394
25 WC-43055
26 WC-43058
27 WC-5231
28 WC-1438
29 WC-7115
30 WC-71183
31 WC-38102
32 WC-3724
33 WC-37260
34 WC-1805
35 WC-1803
36 WC-3707
HEAT SINK ASSY
VALVE, DUAL INLET 120V .5GPM COLD, .25GPM HOT 10W
SUPPORT, DECK PTTD
SUPPORT, DECK EXTENDED SS (SHOWN)
LEG, 4” ADJUSTABLE
LABEL, BOTTOM PTTD
SWITCH, TOGGLE SPST 25A, 125/220VAC RESISTIVE
COVER, TANK W/NOTCHES
FITTING, SYPHON TUBE BRASS
FITTING ASSY, OVERFLOW PLATED, TIN NICKEL
TANK ASSY, COMPLETE
PROBE ASSY, LL W/HEX FITTING, O-RING & NUT
ELEMENT, HEATING 1.6 KW 120V W/JAM NUTS
THERMOSTAT, HI LIMIT HEAT CONTROL DPST 277V 40A
GUARD, SHOCK HTG ELEMENT
GUARD, SHOCK RST TSTAT
PLUG, PP RED DRAIN
COMPOUND, SILICONE 5 OZ
SENSOR, HEATING TANK
LID, TEA OVAL
SHELL W/A TCO-308
LABEL, FRONT
KIT, E-Z VIEW REPLACEMENT
KIT, FAUCET W/ADAPTER COMPL
SEAT CUP, FAUCET S’
FAUCET, SPB
KIT, REPAIR SPB FAUCET
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
SCHEMATIC
WARRANTY We hereby certify that the products manufactured by the Wilbur Curtis Company, Inc., are, to thebest of our knowledge, free from all defects and faulty workmanship.
The following warranties and conditions are applicable:
• 90 Days for Labor and 1 Year Parts from Date of Purchase from Factory: This warranty covers all electrical parts, fittings and tubing.
• 40 Months or 40, 000 Pounds of Coffee on a set of Grinding Burrs. (ADS Grinders)
• 2 Years from Date of Purchase: This warranty covers electronic control boards and leaking or pitting of a stainless steel body of a Brewer or Urn.
• 90 Days from Date of Purchase: On replacement parts that have been installed on out of warranty equipment
All in-warranty service calls must have prior authorization from the manufacturer. For an RMA (Return Merchandise Authorization) number, call the Technical Service Department at 1-800-995-0417. The Wilbur Curtis
Company will allow up to 100 miles, round trip, per in-warranty service call.
CONDITIONS & EXCEPTIONS
The warranty covers original equipment at time of purchase only. The Wilbur Curtis Company, Inc., assumes no responsibility for substitute replacement parts installed on Curtis equipment that have not been purchased
from the Wilbur Curtis Company. Inc The Wilbur Curtis Company will not accept any responsibility if the following conditions are not met. The warranty does not cover and is void under these circumstances:
1) Improper operation of equipment. The equipment must be used for its designed and intended purpose and function.
2) Improper installation of equipment. This equipment must be installed by a professional, certified technician and must comply with all local electrical, mechanical and plumbing codes.
3) Wilbur Curtis Company will not be responsible for the operation of equipment at other than the stated voltages on the serial plate.
4) Abuse or neglect (including failure to periodically clean or remove lime accumulations). Manufacturer is not responsible for variation in equipment operation due to excessive lime or local water
conditions.
5) Replacement of items subject to normal use and wear. This shall include, but is not limited to, light bulbs, shear disks, “0” rings, gaskets, canister assemblies. whipper chambers and plates, mixing
bowls, agitation assemblies and whipper propellers.
6) Any faults resulting from inadequate water supply. This includes, but is not limited to, excessive or low water pressure, and inadequate or fluctuating water flow rate.
7) All repairs and/or replacements are subject to our decision that the workmanship or parts were faulty and the defects showed up under normal use.
8) All labor shall be performed during regular working hours. Overtime charges are the responsibility of the owner.
9) Charges incurred by delays, waiting time, or operating restrictions that hinder the service technician’s ability to perform service is the responsibility of the owner of the equipment.
This includes institutional and correctional facilities.
10) All claims under this warranty must be submitted to the Wilbur Curtis Company Technical Service Department before return of the unit to the factory.
11) All equipment returned to us must be repackaged properly in the original carton. No units will be accepted if they are damaged in transit due to improper packaging.
12) Damaged in transit.
13) The resetting of safety thermostats and circuit breakers, programming and temperature adjustments are the responsibility of the equipment owner.
NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA). RMA NUMBER MUST BE MARKED ON THE CARTON OR SHIPPING LABEL.
All in-warranty service calls must be performed by an authorized service center, where service is available. Call the factory for location near you.
WILBUR CURTIS CO., INC.
6913 Acco St., Montebello, CA 90640-5403 USA
Phone: 800/421-6150
Fax: 323-837-2410
FOR THE LATEST SPECIFICATION INFORMATION GO TO WWW.WILBURCURTIS.COM
4
Printed in U.S.A. 6/03 F-3131-S Rev A
6/5/03 .10.8 . ecn 5894 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
|