TWO SPEED
AUTOMATIC WASHERS
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service call: 1-800-253-1301
In Canada, for assistance call: 1-800-461-5681,
for installation and service call: 1-800-807-6777
or visit our website at
Table of Contents.................................................................2
3955155A
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic
precautions, including the following:
ꢀ
ꢀ
Read all instructions before using the washer.
ꢀ
ꢀ
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is
used near children.
Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
discarded,
Before the washer is removed from service or
remove the door or lid.
ꢀ
ꢀ
Do not reach into the washer if the drum, tub or agitator
is moving.
ꢀ
ꢀ
Do not add gasoline, dry-cleaning solvents, or
other flammable, or explosive substances to the
wash water. These substances give off vapors
that could ignite or explode.
Do not install or store the washer where it will be
exposed to the weather.
ꢀ
ꢀ
Do not tamper with controls.
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not
been used for such a period, before using the
washing machine, turn on all hot water faucets
and let the water flow from each for several
minutes. This will release any accumulated
hydrogen gas. As the gas is flammable, do not
smoke or use an open flame during this time.
Do not repair or replace any part of the washer or
attempt any servicing unless specifically recommended
in this manual or in published user-repair instructions
that you understand and have the skills to carry out.
ꢀ
See “Electrical Requirements” for grounding instructions.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND FEATURES
This manual covers several different models. The washer you have purchased may have some or all of the parts and features listed
below.
1. Control panel
Other features your washer may have
XTRA ROLL ACTION™ PLUS agitator
DURASMOOTH™ white porcelain basket
Extra rinse selector
2. Model and serial number label
3. Liquid fabric softener dispenser
4. Agitator
†
5. Lid
†
†
On some models
6. Liquid chlorine bleach dispenser
7. Basket
8. Tub
Control panel
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading
WASHER USE
Loading suggestions
For these suggested full-sized loads, set the LOAD SIZE selector
to the highest load size setting.
Understanding Washer Cycles
SUPER CAPACITY PLUS WASHERS
When the Cycle Control knob is set to a number and pulled out,
the washer fills (to the selected load size) before agitation and
timing start. The washer begins agitating immediately after filling;
agitation occurs with the washer lid up or down.
Heavy Work Clothes
3 pair pants
3 shirts
1 coverall
1 overall
During agitation, the agitator creates a continuous rollover action
(on some models) that provides a thorough cleaning of the wash
load.
4 pair jeans
Delicates
3 camisoles
1 quilted robe
4 slips
2 sets of sleepwear
1 child’s outfit
6 undergarments
Towels
10 bath towels
10 hand towels
14 wash cloths
1 bath mat
After agitation starts, the Cycle Control knob turns clockwise until
it points to an OFF area and the cycle ends.
Mixed Load
3 double sheets
4 pillowcases
8 T-shirts
NOTE: The washer pauses briefly throughout each cycle. These
pauses are normal for washer operation.
2 shirts
2 blouses
8 handkerchiefs
WASH
RINSE
6 pair shorts
1. Fill
1. Fill
EXTRA LARGE CAPACITY WASHERS
Heavy Work Clothes
2 pair pants
3 shirts
3 pair jeans
1 coverall
2. Wash
selected
time
2. Rinse
3. Drain
Delicates
3 camisoles
4 slips
2 sets of sleepwear
6 undergarments
†
3. Drain
No agitation
No agitation
Towels
8 bath towels
8 hand towels
10 wash cloths
1 bath mat
Mixed Load
4. Spin
4. Spin-Spray
rinse
2 double sheets or
1 king size sheet(s)
4 pillowcases
6 T-shirts
6 pair shorts
2 shirts
2 blouses
6 handkerchiefs
5. Spin
6. Off
Normal Washer Sounds
Your new washer may make sounds your old one didn’t. Because
the sounds might be unfamiliar, you may be concerned about
them. These sounds are normal.
†
The Casual/Permanent
Press cycle partially
drains, fills, agitates
briefly, and drains.
During washing
When you select a small load size setting, your washer has a
lower water level. This can cause a clicking sound from the upper
part of the agitator.
During drain
If water is drained quickly from your washer (depending on your
installation), you may hear air being pulled through the pump
during the end of draining.
After drain and before spin
When the cycle changes from draining to spinning, you may hear
gears engaging.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
ꢀ
Items should move easily through the wash water.
Overloading can cause poor cleaning.
Starting Your Washer
To reduce wrinkling of permanent press clothes and some
synthetic knits, use a large load size to provide more space
(see step 5).
2. (OPTIONAL) Pour measured liquid chlorine bleach into the
liquid chlorine bleach dispenser (on some models). Bleach
will be diluted automatically during the wash part of the cycle.
Fire Hazard
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
ꢀ
Never use more than 1 cup (250 mL) for a full load. Use
less with a smaller load size.
No washer can completely remove oil.
ꢀ
ꢀ
Follow the manufacturer’s directions for safe use.
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
To avoid spilling, use a cup with a pouring spout. Do not
let bleach splash, drip, or run down into the washer
basket.
Doing so can result in death, explosion, or fire.
ꢀ
Use only liquid chlorine bleach in this dispenser.
NOTE: On models without a bleach dispenser, see “Adding
Liquid Chlorine Bleach.”
3. (OPTIONAL) Pour measured liquid fabric softener into the
liquid fabric softener dispenser (on some models). Softener is
added automatically during the rinse portion of the cycle.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Dilute liquid fabric softener by filling the dispenser with warm
water until liquid reaches the crossbar in the opening.
ꢀ
ꢀ
Do not spill or drip any fabric softener on the clothes.
Use only liquid fabric softener in this dispenser.
Do not use an extension cord.
NOTE: On models without a fabric softener dispenser, see
“Adding Liquid Fabric Softener.”
Failure to follow these instructions can result in
death, fire, or electrical shock.
4. Close the washer lid.
5. Turn the LOAD SIZE selector to the correct setting for your
wash load and the type of fabric being washed.
1. Measure detergent and pour it into the washer. If desired, add
powdered or liquid color safe bleach. Add extra detergent for
the Super Wash cycle.
ꢀ
ꢀ
Choose a load size that allows the load to move freely for
best fabric care. See "Loading."
You may change the load size selection after the washer
has started filling by turning the selector to a different
setting.
Drop a sorted load of clothes loosely into your washer.
ꢀ
Load evenly to maintain washer balance. Mix large and small
items.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Set the TEMPERATURE selector to the correct setting for the
type of fabric and soils being washed. Use the warmest water
safe for fabric. Follow garment label instructions.
Selecting a Cycle and Time
This section describes the available wash cycles and will help
you make the best cycle selections for your wash loads. Each
cycle is designed for different types of fabric and soil levels.
Water Temp
Use For
Hot
Whites and pastels
ꢀ
The washer pauses briefly throughout each cycle. These
pauses are normal. Refer to “Normal Washer Sounds” to
learn more about the sounds you may hear during a wash
cycle.
111°F (44°C)
or above
Heavy and greasy soils
Warm
Bright colors
ꢀ
Refer to “Understanding Washer Cycles” to learn what
happens during a wash cycle.
90°-110°F
(32°-43°C)
Moderate to light soils
NOTE: This manual covers several different washer models. The
washer you have purchased will not have all of the cycles
described.
Cold
70°-90°F
(21°-32°C)
Colors that bleed or fade
Light soils
NOTE: In wash water temperatures colder than 70ºF
(21ºC), detergents do not dissolve well. Soils can be difficult
to remove. Some fabrics can retain wear wrinkles and have
increased pilling (the formation of small lint-like balls on the
surface of garments).
7. (OPTIONAL) Some models have an EXTRA RINSE selector.
For an additional rinse and spin at the end of a wash cycle,
set the EXTRA RINSE selector to ON. On some models, the
Extra Rinse feature is part of the cycle.
8. (OPTIONAL ) Some models have an END OF CYCLE SIGNAL
selector. Set the END OF CYCLE SIGNAL selector to ON if
you want your washer to alert you when the wash cycle is
complete. The signal is helpful when you are washing items
that should be removed from the washer as soon as the cycle
ends.
Heavy cycle
This cycle features high-speed agitation followed by brief periods
of low-speed agitation for cleaning sturdy fabrics and heavily
soiled loads that need maximum soil removal. Select Super Wash
or Regular depending on whether your load is moderately or
heavily soiled. For improved cleaning, use twice the amount of
detergent recommended for a wash cycle. The Heavy cycle
features Extra Rinse as part of the cycle.
9. Push in the Cycle Control knob and turn it clockwise to the
wash cycle you want. Reduce the wash time when using a
small load size setting. See “Selecting a Cycle and Time.”
Normal cycle
This cycle features high-speed agitation followed by a brief
period of low-speed agitation for cleaning cottons and linens.
High spin speeds shorten drying time. Select 6 to 15 minutes of
wash time, depending on your model, for loads that are
moderately or heavily soiled. For lightly soiled loads, use the
shortest time setting.
Pull out the Cycle Control knob to start the washer.
To stop or restart your washer
Super Wash - Select the Super Wash setting to wash heavily
soiled loads that need maximum soil removal. Use twice the
amount of detergent recommended for a wash cycle.
ꢀ
To stop the washer at any time, push in the Cycle Control
knob.
Casual/Permanent Press cycle
ꢀ
To restart the washer, close the lid (if open) and pull out
the Cycle Control knob.
This cycle starts with high-speed agitation and then steps down
to low-speed agitation for cleaning permanent press blends and
synthetic fabrics. To minimize wrinkling, this cycle features a
cool-down rinse and a low-speed final spin. Select 6 to 10
minutes of wash time, depending on your model, to clean lightly
to moderately soiled loads.
Adding bleach to models without a bleach dispenser
If desired, add measured liquid chlorine bleach after the washer
starts agitating. Pour diluted bleach around the agitator, not
directly on the load. Undiluted bleach will damage any fabric it
touches. (See "Adding Liquid Chlorine Bleach.")
Delicates cycle
Adding softener to models without a fabric softener
dispenser
This cycle features low-speed agitation for gentle soil removal
from delicate items and washable knits. Low spin speeds
minimize wrinkling. Select 3 to 9 minutes of wash time,
depending on your model, to clean lightly to moderately soiled
loads.
If desired, add measured liquid fabric softener to the final rinse
water. Always dilute fabric softener with ½ to 1 cup
(125 to 250 mL) of warm water. Undiluted fabric softener can
stain fabrics. (See "Adding Liquid Fabric Softener.")
Hand Washables cycle
This cycle features a series of brief, low-speed agitations and
short soaks to gently clean special-care items. Low spin speeds
minimize wrinkling. Wash small loads. If items appear to be
floating (due to trapped air), stop the washer by pushing in the
Cycle Control knob. Push items down into the washer. Restart
the washer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Wash cycle
This cycle features low-speed agitation for gentle soil removal,
while providing high spin speeds to shorten drying times. Select
this cycle for small loads of lightly soiled items that you need in a
hurry.
Adding Liquid Fabric Softener
Always dilute fabric softener with ½ to 1 cup (125 to 250 mL)
warm water. Undiluted fabric softener can stain fabrics.
ꢀ
Add diluted fabric softener only in the final rinse.
Soak cycle
This cycle features brief periods of agitation and soak time to
remove heavy soils and stains that need pretreatment. Use warm
water when soaking laundry. Hot water can set stains. Use the
amount of detergent or presoak additive recommended by the
manufacturer. When the Soak cycle ends, add detergent and
start a new wash cycle.
ꢀ
Fabric softener should not be mixed with other laundry
products. Greasy stains can form. To remove greasy stains,
wet the stain and rub with liquid detergent or a bar of soap.
Rewash.
ꢀ
Too much fabric softener can make some items (diapers and
towels) nonabsorbent. If this happens, use less fabric
softener, or do not use it every time.
Pre-Wash cycle
This cycle features a brief period of agitation to help remove
heavy soils and stains that need pretreatment. Use the amount of
detergent or presoak additive recommended by the
manufacturer. After the Pre-Wash cycle ends, add detergent and
set a new wash cycle.
WASHER CARE
Cleaning Your Washer
Rinse and Spin
Cleaning the exterior
When using extra detergent for heavily soiled clothes, or washing
special-care items, you may find an extra rinse and spin is
needed.
Use a soft, damp cloth or sponge to wipe up any spills such as
detergent or bleach. Occasionally wipe the outside of your
washer to keep it looking new.
1. Push in the Cycle Control knob and turn it clockwise to any of
the Rinse settings.
Cleaning the interior
Clean your washer interior by mixing 1 cup (250 mL) of chlorine
bleach and 2 cups (500 mL) of detergent. Pour this into your
washer and run it through a complete cycle using hot water.
Repeat this process if necessary.
2. Pull out the Cycle Control knob. The washer fills to the
selected load size, agitates, drains, and spins.
NOTE: An Extra Rinse option is available (on some models). See
“Starting Your Washer.”
NOTE: Remove any hard water deposits using only cleaners
labeled as washer safe.
Drain and Spin
Cleaning the liquid fabric softener dispenser
A drain and spin may help shorten drying times for some heavy
fabrics or special-care items by removing excess water.
Flush dispenser periodically with warm water, as shown. Remove
the dispenser by grasping the top of the dispenser with both
hands and squeezing and pushing upwards with thumbs. Clean
the dispenser by rinsing it under a water faucet. Replace it after
cleaning.
1. Push in the Cycle Control knob and turn it clockwise to any of
the Spin settings.
2. Pull out the Cycle Control knob. The washer drains, then
NOTE: Do not wash clothes with this dispenser removed. Do not
add detergent or bleach to this dispenser; it is for liquid fabric
softener use only.
spins.
Adding Liquid Chlorine Bleach
Always measure liquid chlorine bleach. Do not guess. Never use
more than 1 cup (250 mL) for a full load. Follow manufacturer’s
directions for safe use. Use a cup with a pouring spout to avoid
spilling.
1. Let the washer fill and begin agitating the load.
2. Add bleach to the wash cycle so it can be removed in the
rinse cycle. Pour bleach around the agitator, not directly on
the load.
ꢀ
Follow directions on the care labels. Do not use chlorine
bleach on wool, silk, spandex, acetates, or some flame-
retardant fabrics.
Water Inlet Hoses
Replace inlet hoses after five years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear or leaks are found.
ꢀ
When soaking with chlorine bleach, add detergent to
soak water.
NOTE: Undiluted bleach will damage any fabric it touches. The
damage appears as rips, holes, tears, or color loss and may not
show up until several washings later.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer stops
Vacation, Storage and Moving Care
ꢀ
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
Non-use or vacation care
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
ꢀ
Unplug washer or disconnect power.
ꢀ
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
ꢀ
ꢀ
ꢀ
ꢀ
Is there power at the plug?
Check your electrical source or call an electrician.
Has a fuse blown or is the circuit breaker open?
If problem continues, call an electrician.
To winterize washer
1. Shut off both water faucets.
Are you using an extension cord?
Do not use an extension cord.
2. Disconnect and drain water inlet hoses.
3. Put 1 quart (1 L) of R.V.-type antifreeze in the basket.
4. Run washer on a drain and spin setting (see “Drain and Spin”)
Is the washer in a normal pause in the Casual/Permanent
Press (or Hand Washables) cycle?
The washer pauses for about 2 minutes in the Casual/
Permanent Press cycle. Allow the cycle to continue.
for about 30 seconds to mix the antifreeze and water.
5. Unplug washer or disconnect power.
The Hand Washables cycle (on some models) features
periods of agitation and soak.
To use washer again
1. Flush water pipes and hoses.
ꢀ
ꢀ
Is the washer overloaded?
2. Reconnect water inlet hoses.
3. Turn on both water faucets.
4. Plug in washer or reconnect power.
Wash smaller loads.
Washer won’t drain or spin
5. Run the washer through a complete cycle with 1 cup (250 mL)
of detergent to clean out antifreeze.
Is the drain hose clogged, or the end of the drain hose
more than 72 in. (183 cm) above the floor?
See the Installation Instructions for proper installation of drain
hose.
ꢀ
ꢀ
Is the lid open?
TROUBLESHOOTING
The lid must be closed during operation.
First try the solutions suggested here and possibly avoid
the cost of a service call...
Is there excessive sudsing?
Always measure detergent. Follow manufacturer’s directions.
If you have very soft water, you might need to use less
detergent.
Washer won’t fill, rinse or agitate
ꢀ
Is your voltage low?
Check your electrical source or call an electrician. Do not use
an extension cord.
ꢀ
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
Washer continues to fill or drain, or the cycle seems stuck
ꢀ
ꢀ
Is the top of drain hose lower than the water level in
washer?
The top of the hose must be higher than the water level in the
washer for proper operation. See the Installation Instructions.
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe?
The drain hose should be loose yet fit securely. Do not seal
the drain hose with tape. The hose needs an air gap. See the
Installation Instructions.
ꢀ
Does the water level seem too low, or does the washer
appear to not fill completely?
The top of the agitator is much higher than the highest water
level. This creates a perception that the washer is not filling
completely. This is normal.
Washer makes noise
ꢀ
Is the load balanced and the washer level?
The wash load should be balanced and not overloaded.
The washer must be level. The front feet should be properly
installed and the nuts tightened. Reset the rear leveling legs
(if needed). See the Installation Instructions.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
ꢀ
Did you completely remove the yellow shipping strap with
cotter pins?
Residue or lint on load
See the Installation Instructions.
ꢀ
ꢀ
ꢀ
Did you sort properly?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
Are the gears engaging after the drain and before spin, or
is the upper part of agitator clicking during wash?
These are normal washer noises.
Did you overload the washer?
The wash load must be balanced and not overloaded. Lint
can be trapped in the load if overloaded. Wash smaller loads.
Washer leaks
ꢀ
Check the following:
Check the following:
Was paper or tissue left in the pockets?
Are the fill hoses tight? Are the fill hose washers properly
seated? Is the drain hose clamp properly installed? See the
Installation Instructions.
Did you use enough detergent? Follow manufacturer’s
directions. Use enough detergent to hold the lint in the water.
ꢀ
ꢀ
Is the sink or drain clogged?
Sink and standpipe must be able to handle 17 gallons (64 L)
of water per minute.
Is your water colder than 70°F (21°C)? Wash water colder
than 70°F (21°C) may not completely dissolve the detergent.
Is water deflecting off the tub ring or the load?
Center the tub before starting the washer.
Stains on load
ꢀ
Did you follow the manufacturer’s directions when adding
detergent and fabric softener?
Measure detergent and fabric softener. Use enough detergent
to remove soil and hold it in suspension.
The wash load should be balanced and not overloaded. The
fill or spray rinses can deflect off the load.
The washer must be level. The front feet should be properly
installed and the nuts tightened. Reset the rear leveling legs
(if needed). See the Installation Instructions.
Dilute fabric softener and add to the rinse portion of a cycle
only. Do not drip fabric softener on clothes.
ꢀ
Check household plumbing for leaks.
ꢀ
ꢀ
ꢀ
Is there above average iron (rust) in water?
You may need to install an iron filter.
Washer basket is crooked
Did you properly sort the load?
Sort dark clothes from whites and lights.
ꢀ
ꢀ
Was the washer basket pulled forward during loading?
The wash load should be balanced and not overloaded. Push
the basket to the center before starting wash.
Did you unload the washer promptly?
To avoid dye transfer, unload the washer as soon as it stops.
Is the load balanced and the washer level?
The wash load should be balanced and not overloaded.
Load is wrinkled
The washer must be level. The front feet should be properly
installed and the nuts tightened. Reset the rear leveling legs
(if needed). See the Installation Instructions.
ꢀ
ꢀ
Did you unload the washer promptly?
Unload the washer as soon as it stops.
Did you use the right cycle for the load being washed?
Use the Casual/Permanent Press cycle or another cycle with
low spin speeds (if available) to reduce wrinkling.
ꢀ
ꢀ
The washer basket moves while washing.
This is normal.
ꢀ
ꢀ
Did you overload the washer?
The wash load must be balanced and not overloaded. Loads
should move freely during washing.
Agitator operation
The top of the agitator is loose, or moves in only one
direction.
This is normal.
Was the wash water warm enough to relax wrinkles, or
are you using warm rinses?
If safe for the load, use warm or hot wash water. Use cold
rinse water.
Dispensers clogged or bleach leaking
ꢀ
Are the hot and cold water hoses reversed?
Check to be sure the hot and cold water hoses are connected
to the right faucets. See the Installation Instructions.
ꢀ
ꢀ
Did you follow the manufacturer’s directions when adding
detergent and fabric softener to the dispensers?
Measure detergent and fabric softener. Carefully pour into the
dispensers. Wipe up all spills.
Load is tangled or twisted
Dilute fabric softener in the fabric softener dispenser.
Did you put powdered or color-safe bleach in the liquid
chlorine bleach dispenser?
Add powdered or liquid color-safe bleach directly to the
basket. Do not use the chlorine bleach dispenser for color-
safe bleach.
ꢀ
ꢀ
Did you overload the washer?
The wash load must be balanced and not overloaded. Loads
should move freely during washing.
Did you wrap items around the agitator?
Drop items loosely into the washer. Do not wrap items around
the agitator.
Load too wet
ꢀ
ꢀ
Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed (if available).
Did you use a cold rinse?
Cold rinses leave loads wetter than warm rinses. This is
normal.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Gray whites, dingy colors
In the U.S.A.
ꢀ
ꢀ
ꢀ
Did you properly sort the load?
Dye transfer can occur when mixing whites and colors in a
load. Sort dark clothes from whites and lights.
Call the Whirlpool Customer Interaction Center toll free:
1-800-253-1301.
Our consultants provide assistance with:
Was the wash temperature too low?
Use hot or warm washes if safe for the load. Hot water should
be at least 111°F (44°C) to clean heavy or greasy soils.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Features and specifications on our full line of appliances
Installation information
Use and maintenance procedures
Accessory and repair parts sales
Did you use enough detergent, or do you have hard
water?
Use more detergent for washing heavy soils in cold or hard
water.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.)
ꢀ
Are the hot and cold water hoses reversed?
Check to be sure the hot and cold water hoses are connected
to the right faucets. See the Installation Instructions.
ꢀ
Referrals to local dealers, repair parts distributors, and
service companies
Whirlpool designated service technicians are trained to fulfill the
product warranty and provide after-warranty service anywhere in
the United States.
Garment damage
ꢀ
Check the following:
To locate the Whirlpool designated service company in your area,
you can also look in your telephone directory Yellow Pages.
Were sharp items removed from pockets before washing?
Empty pockets, zip zippers, snap or hook fasteners before
washing.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Were strings and sashes tied to prevent tangling?
Were items damaged before washing? Mend rips and broken
threads in seams before washing.
Whirlpool Brand Home Appliances
Customer Interaction Center
553 Benson Road
ꢀ
ꢀ
ꢀ
Did you overload the washer?
The wash load must be balanced and not overloaded. Loads
should move freely during washing.
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Did you properly add chlorine bleach?
Do not pour chlorine bleach directly on load. Wipe up bleach
spills. Undiluted bleach will damage fabrics.
In Canada
Did you follow the manufacturer’s care label instructions?
Call the Inglis Limited Customer Interaction Center toll free:
1-800-461-5681 8:30 a.m. - 5:30 p.m. (EST).
Our consultants provide assistance with:
ASSISTANCE OR SERVICE
ꢀ
Features and specifications on our full line of appliances
Referrals to local dealers
ꢀ
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
For service in Canada
Call 1-800-807-6777. Inglis designated service technicians are
trained to fulfill the product warranty and provide after-warranty
service anywhere in Canada.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
For further assistance
If you need further assistance, you can write to Inglis Limited with
any questions or concerns at:
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use FSP® factory specified parts. These parts will fit right
and work right because they are made with the same precision
used to build every new WHIRLPOOL® appliance.
Customer Interaction Center
Inglis Limited
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
To locate FSP replacement parts in your area:
Please include a daytime phone number in your correspondence.
In the U.S.A., call the Customer Interaction Center at
1-800-253-1301, or your nearest designated service center.
Gearcase assembly covered by your warranty
In Canada, call 1-800-807-6777, or your nearest designated
service center.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
®
WHIRLPOOL WASHER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this washer is operated and maintained according to instructions attached to or furnished
®
with the product, Whirlpool Corporation will pay for FSP replacement parts and repair labor to correct defects in materials or
workmanship. Service must be provided by a Whirlpool designated service company.
FIVE-YEAR LIMITED WARRANTY
For five years from the date of purchase, when this washer is operated and maintained according to instructions attached to or
®
furnished with the product, Whirlpool Corporation will pay for FSP replacement parts for any top and lid rust and any part of the
gearcase assembly, if defective in materials or workmanship.
TEN-YEAR LIMITED WARRANTY
For ten years from the date of purchase, when this washer is operated and maintained according to instructions attached to or
®
furnished with the product, Whirlpool Corporation will pay for FSP replacement parts for the outer tub should it crack or fail to contain
water, if defective in materials or workmanship.
LIFETIME LIMITED WARRANTY
For the lifetime of the washer, when this washer is operated and maintained according to instructions attached to or furnished with the
®
product, Whirlpool Corporation will pay for FSP replacement parts for the white porcelain basket should it chip or rust due to defects in
materials or workmanship.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your washer, to instruct you how to use your washer, or to replace house fuses or correct
house wiring or plumbing.
2. Repairs when your washer is used in other than normal, single-family household use.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with local electrical and plumbing codes, or use of products not approved by Whirlpool Corporation.
4. Any labor costs during the limited warranties.
5. Replacement parts or repair labor costs for units operated outside the United States and Canada.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. In Canada, travel or transportation expenses for customers who reside in remote areas.
WHIRLPOOL CORPORATION AND INGLIS LIMITED SHALL
NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Outside the 50 United States and Canada, this warranty does
not apply. Contact your authorized Whirlpool dealer to
determine if another warranty applies.
Some states and provinces do not allow the exclusion or
limitation of incidental or consequential damages, so this
exclusion or limitation may not apply to you. This warranty gives
you specific legal rights and you may also have other rights which
vary from state to state or province to province.
If you need service, first see “Troubleshooting”. Additional help
can be found by checking “Assistance or Service,” or call our
Customer Interaction Center at 1-800-253-1301 from anywhere
in the U.S.A., or write: Whirlpool Brand Home Appliances,
Customer Interaction Center, 553 Benson Road, Benton Harbor,
MI 49022-2692. In Canada, call Inglis Limited at 1-800-807-6777.
04/00
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your washer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number.
You can find this information on the model and serial number
label/plate, located on your appliance as shown in
“Parts and Features”.
3955155A
© 2001 Whirlpool Corporation.
3/01
Printed in U.S.A.
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A., Inglis Limited licensee in Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
|