Before using the dishwasher, read the user instructions!
GB
ADP 4501/ 5
Quick Reference Guide
Indicators
Add regeneration salt
Programme selector knob
Start button
Only add regeneration salt immediately
before starting a wash programme.
Add rinse aid
Switches “on” when the dishwasher is
operating. Flashes when a fault occurs.
Switches off at the end of the programme.
ON / OFF button
Detergent 2)
Consumption 3)
Litres kWh Minutes
Programme chart
Programmes
Pre-Rinse
Loading instructions
A
B
Crockery to be washed later.
-
-
5.0 0.02
13.0 0.70
19.0 1.05
16.0 1.65
10
30
cold
Lightly soiled crockery with no
dried-on food.
X
X
X
-
Quickwash
40° C
50° C
65° C
1)
Normally soiled crockery.
X
X
170
100
Eco Normal
Normal
Normally or heavily soiled crockery.
Recommended programme for
heavily soiled crockery, especially
suitable for pans and saucepans.
X
X
17.0 1.90
135
Intensive
70° C
1)
2)
Reference programme for energy label in compliance with
EN 50242 regulations;
3)
Programme data obtained in conformity with European
standard EN 50242. Values may vary in relation to usage, e.g.:
different loads, water temperatures - above or below 15°C -
as well as water hardness and power supply voltage, etc.
Refer to “User instructions“;
Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
5019 396 98090
Whirlpool is a registered trademark of Whirlpool USA
(We reserve the right to make technical modifications)
Download from Www.Somanuals.com. All Manuals Search And Download.
Dishwasher loading instructions and racks provided
depending on the model
Upper rack:
1)
Multi-purpose support (A):
Depending on the position, for long-
handles utensils, cups and glasses. May
be used in three different positions.
Crockery holders (B):
Depending on the position, for example
plates, cups and long-stemmed glasses.
2)
Revolving glass support (C):
Depending on the position, for example
small or long-stemmed glasses.
Long-handled utensils (e.g. carving
forks, knives) must be arranged
with the sharp end facing in
towards the appliance.
Half Load:
Load the upper rack only.
Place the cutlery basket (D) in the
upper rack.
Rack height adjustment
(also when loaded):
•
•
Lower adjustment: pull out the
two rack handles outwards (E)
and lower the rack.
Upper adjustment: pull the two
handles (E) upwards until the rack
clicks into place (Factory setting).
The rack must be level on both
sides.
Removing the top rack to provide
clearance for large items of
crockery in the bottom rack:
Open the rack guide retainers (F) on the
right and left and remove the top rack.
When the upper rack is in place the
retainers must always be closed.
Retainer
Retainer
open
closed
F
F
Lower rack:
Depending on the model with fixed or
tilting plate holders (G).
Half Load:
Load the lower rack only.
Greater washing power, particularly
for plates and saucepans.
Cutlery basket (J) or (H):
Some models are provided with a grid
(I) that can be fitted onto the cutlery
basket to keep items separated.
Cutlery basket (D), if provided, for
appliances with half load only.
Sharp knives and forks that might
cause injury must be placed in the
cutlery basket with the sharp end
facing downwards.
Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a dishwasher,
for example wooden items, aluminium, plastic utensils, tin, hand-decorated crockery (unglazed), silver cutlery.
Spare parts which are sold separately:
1)
Multi-purpose support (A) - N. AMH 369 series.
Revolving glass support (C) - N. WGH 1000 series.
2)
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do if...
If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem
(* see also the corresponding chapter in the user instructions).
Problem
Cause
Remedy
•
No water supply.
•
Open the tap.
The appliance is not
working
•
•
The appliance does not load
sufficient water.
•
•
Clean the water supply tap filter.
Ensure there are no kinks in the water hose.
There is a power failure.
•
•
•
•
Insert the plug into the mains socket.
Press the Start button.
Close the door.
Check the domestic circuit fuse.
•
•
Starting the selected programme.
Insufficient rinse aid.
•
The programme can be set to “0” to start.
•
Increase dosage *.
If crockery is not
perfectly dry
•
•
Residual water in cavities.
•
•
Load crockery at an angle.
The water jet does not reach
the crockery.
Arrange crockery so that items do not touch each
other.
Load crockery upside down.
If crockery is not
perfectly clean
•
•
•
•
•
Insufficient detergent.
•
•
•
•
•
Follow recommended detergent dosage.
Select a more intense wash cycle.
Unsuitable programme.
Spray arms blocked.
The spray arms must be able to turn freely.
Remove any impurities obstructing the water flow *.
Use a good quality detergent.
Spray arm nozzles clogged.
Incorrect detergent/ detergent too old.
•
•
Clogged filters.
•
•
Check filters regularly/ if necessary clean *.
Insert the filter correctly *.
Sandy or grainy residues
Filters incorrectly assembled.
•
Tomato/ carrot juice,...
•
Depending on the material, if necessary use a
detergent with a greater whitening power.
Colour of plastic parts
faded
Deposits on crockery
•
•
removable
•
•
•
•
Streaks on the crockery/ glasses.
Streaks on glasses.
•
•
•
•
Increase the rinse aid dosage *.
Reduce the rinse aid dosage *.
Close the salt container lid properly *.
Layer of salt on crockery/ glasses.
not removable
Insufficient water softening,
calcium deposits.
Change water hardness setting, if necessary add
salt *.
•
•
Cannot be washed in the dishwasher.
•
Use suitable glasses.
Opaque glasses/
glasses not sparkling
Not made of stainless steel.
•
•
Use suitable cutlery.
Rust on cutlery
•
•
The START indicator lamp flashes.
Indicator F... (if provided).
Ensure the filter assembly is not clogged and that
there is no interruption to the water supply
(if necessary, clean the filters *). Start the programme
again. Press the START button for 2 seconds, until the
START indicator lamp switches off. Select a new
programme and press the Start button again.
Identifying appliance
faults
If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the
water supply tap, then call our After-Sales Service (see guarantee).
Before contacting our After-Sales Service, take note of the following:
•
•
•
The nature of the fault.
The appliance type and model.
The service code (the number indicated on the adhesive rating plate)
inside the door on the right-hand side.
Download from Www.Somanuals.com. All Manuals Search And Download.
|