Quick reference guide
Chart
ON
BUTTON
PROGRAMME SELECTION BUTTON
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE ASSEMBLY
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Press button “P” (repeatedly) until the indicator of the required programme lights up (see “Table of
programmes” below).
OFF
BUTTON
START BUTTON
The indicator lights up during operation, flashes when a fault occurs and goes off at the end of the programme.
START BUTTON RESET FUNCTION
Press this button for at least 2 seconds; the selected programme and options are cancelled. Main failure
displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING. Detailed
instructions are given in chapter “What to do if...”.
Consumption
Table of programmes
Programmes Loading instructions
Deter-
gent
Litres kWh
P
Minutes 1)
Crockery to be washed later.
cold
—
5.0
0.02
10
30
Pre-Wash
1
Lightly soiled crockery, with no
dried-on food. * Use of tablets
not recommended.
X * 13.0 0.70
Quickwash 40°C
2
3
4
Normally soiled crockery.
Energy-saving programme.
2)
50°C
Eco
X
X
15.0 1.05
17.0 1.65
165
145
Recommended programme for
heavily soiled crockery, especially
suitable for pots and pans.
Intensive
70°C
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programmes as a result of the appliance’s automatic calibration system.
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
ADG 7470
5019 396 01787
GB -1-
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Daily check
1
Visual indicator (depending
on model). Screw on the cap.
Salt residues around cap
need to be removed.
Add salt
Visual indicator
(depending
on model).
Fill the salt
(never add
detergent!).
min. 1.5 kg
max. 2 kg
reservoir with
water before the
first wash only.
Unscrew cap.
Salt indicator
(depending on
the model)
The salt level indicator lamp may remain lit for the duration of several wash cycles. If the
water hardness level falls within category (soft), no salt is required.
The indicator lamp on the control panel lights
up when SALT NEEDS TO BE ADDED.
orange: OK.
clear: NEEDS TO BE ADDED
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
The rinse aid dosage can be adjusted to the
detergent used. The lower the setting,
the less rinse aid is dispensed
Visual
indicator
2
(factory setting: position 4).
Press the button to open the cover B. Using a
coin or similar object, turn the arrow to the
desired setting. After adjusting the rinse aid
setting, shut the cover again.
If required,
open the cover
B (press right
button).
Add rinse aid
to the max.
line ~ 150 ml
The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE
ADDED.
Rinse aid indicator (depending on model)
dark: OK.
clear: NEEDS TO BE ADDED
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid
setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend
to form excess suds.
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Daily use
Tablet / gel / powder
Use only one tablet per one
cycle, only placed in detergent
dispenser.
3
By pressing
dedicated ribs
shut the cover.
Open the cover A Only fill the
(press left button). detergent dispenser
prior to starting a
All types of tablets can be
used, but for 2 in 1 type
adding of salt is mandatory.
wash programme.
GB -3-
Download from Www.Somanuals.com. All Manuals Search And Download.
How to load UPPER RACK
How to load the racks
(In some models only)
A - Multipurpose support: Different positions for long
utensils, cups and glasses.
B - Adjustable flaps: In horizontal position for cups/long utensils,
in raised position for plates and stemware.
(In some models only)
C - Cutlery basket: It can be placed in the upper rack when the
“Half load/Multizone” option is selected.
4
D - Adjustable glass holder
How to adjust upper rack height (if available)
- It could be useful to lift up upper rack to have more space in
lower rack or bring it down to load long stem glasses.
- Grasp and take out the two lateral handles (E) (must be on same
level) and lift up or take down the upper rack.
How to remove upper rack (if available)
- It could be useful to remove upper rack to load bulky items in
lower rack.
- Open the two retainers (F) to take off the upper rack. When
the upper rack is in place the retainers must always be closed.
F - OPEN
F - CLOSED
How to load LOWER RACK
(depending on the model)
G - Foldable plate holders: They can be folded down to load pots
or
H- Fixed plate holders
I - Cutlery basket (or J model)
K - Grid: Helps to keep the cutlery separate for better washing results.
H
I
J
Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely. Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden
items, aluminium, tin, silver cutlery or decorated crockery (unglazed). In the baskets, dishes (e.g. plates, bowls, pots) must be placed in a correct way to let water flow down!
5
Switching on the appliance
GB -4-
Download from Www.Somanuals.com. All Manuals Search And Download.
Select programme
Quick, permanent or alternating
Overview of programmes
The max. possible number of programmes is illustrated in the chapter “Chart”. The corresponding programmes for your appliance can be found on the panel (page 1).
6
Choose programme according to the attached table of programmes (page 1).
Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc.
Wash cycle
The dishwasher door must be closed and the water tap open.
Change the programme in progress:
To load crockery, open the door with caution:
•
Press the START button (for 2 seconds) until the START indicator lamp
switches off.
Close the door.
(Water drains for up to 60 seconds).
Open the door.
7
Beware of hot steam!
•
•
•
•
•
Close the door again.
The programme resumes the cycle from where it was interrupted.
Select a new programme.
Press the START button.
The wash cycle can be interrupted at any time by pressing START (see chapter “What to do if...”).
Switch off the appliance Everything o.k. ...
Exercise caution when opening the door: beware of hot steam.
Only press the OFF button once the START indicator lamp has switched off.
8
All the indicator lamps switch off. Unload the appliance, starting from the lower rack in order to avoid any residual drips of water falling onto crockery below.
Maintenance and care
Maintenance and care
Screw on filter cylinder NOTE MARK!
9
Filters
Check and
clean if
Unscrew filter
cylinder, remove it
and fine sieve...
Rinse under running
water ...
Insert
necessary
Rectifying minor faults yourself ...
Insert and screw on lower and upper arms tightly.
10
Spray arms
Remove
Unscrew
and remove
lower arm ...
Unscrew
and remove
upper arm ...
Clean spray
nozzles under
running water
(use toothpicks if
necessary) ...
blockages/
deposits.
GB -5-
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do if...
If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action,
quickly restoring normal appliance operation.
The appliance...
Possible causes...
Solutions...
...is not working/will not start
-
-
The appliance must be switched on.
-
-
-
Check the household circuit fuse if there is no power supply.
The dishwasher door doesn't close.
“Delayed start” option is ON.
Check if the dishwasher’s door is closed.
Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only
start once the set time has elapsed. If necessary, set the delayed start to “0” (RESET the appliance).
-
-
...shows “F1” on the display or the START
indicator lamp flashes once
The water supply temperature is below 3°C.
-
Check that the water supply temperature is above 3°C.
...shows “F4” on the display or the START
indicator lamp flashes 4 times
-
-
-
-
Dirty filters.
-
-
-
-
-
Clean the filters.
Kinked drain hose.
Syphon hose connection closed.
Water tap closed.
The drain hose must not be kinked.
The closure disk of the syphon hose connection must be removed.
The water tap must be open.
...shows “F6” on the display or the START
indicator lamp flashes 6 times
The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be
clogged.
-
-
-
Kinked water inlet hose or clogged inlet filters.
Water pressure too low.
...shows “F7” on the display or the START
indicator lamp flashes 7 times
-
-
The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).
The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be
dirty.
Kinked water inlet hose or clogged inlet filters.
...shows “F8” on the display or the START
indicator lamp flashes 8 times
-
-
Dirty or clogged filters.
-
-
-
The filters must not be dirty or clogged.
Too little water in the dishwasher’s water system.
Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.
The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the
lower edge of the appliance) - see Assembly instructions.
Reset the appliance (see below).
-
-
Drain hose incorrectly fitted.
Many different causes.
...shows other “F” faults on the display or
the START indicator lamp flashes Xx times
-
After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.
RESET: Press the START button for approx. 2 seconds until the indicator lamp switches off or press the RESET button (depending on model)
Close the door.
Water drains automatically for up to 60 seconds.
The appliance is now ready to be restarted.
Crockery and cutlery...
...are not perfectly clean/have food residues
Possible causes...
Too little space between dishes (incorrect arrangement
of the concave items in the rack).
Too little detergent; detergent too old or incorrectly
stored.
Solutions...
-
-
-
-
Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be
arranged facing downwards in the rack.
If necessary, use more detergent, observing the manufacturer’s indications as regards dosage. Always store
detergent in a dry place and do not store it for excessively long periods of time.
-
-
Temperature not high enough for heavily soiled crockery.
-
-
For heavily soiled crockery, select a wash programme with a higher temperature (see table of programmes on page 1).
Loading of the dishwasher using lower and upper rack
at the same time with “Half load/Multizone” option.
If you select the “Half load/Multizone” option (if available), remember to load only the upper rack or only
the lower rack to increase washing power and thus obtain optimum wash results.
In the event of frequent use of the Eco 50°C programme (if available), from time to time select the
Intensive 70°C programme (if available).
The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see page 5,
“Maintenance and care”).
-
-
-
Frequent use of Eco 50°C.
-
-
Clogged spray arms; filters dirty or not fitted correctly.
Spray arms impeded by crockery or cutlery.
-
The spray arms must be able to turn freely and must not be impeded by crockery or cutlery.
GB -6-
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do if...
Crockery and cutlery...
...salt indicator lit
...have deposits: regeneration salt residue
Possible causes...
Use tablets for soft water.
Solutions...
-
-
-
-
Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up.
In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water
hardness”).
Water too hard.
-
-
-
-
Salt reservoir cap open.
Not enough rinse aid.
-
-
-
-
Close the salt reservoir cap properly.
If you use a combined action detergent, try adding more rinse aid.
Synthetic materials do not dry well; if wet at end of cycle, wipe dry.
...are not dry
Plastic containers dry badly.
Clean dishes left in dishwasher for a long time after end
of cycle (e.g. when using “delayed start” option).
In this situation, the presence of drops of water on dishes and on the sides of the dishwasher is normal. Try
releasing the door 5 minutes before removing the dishes.
-
-
Incorrect arrangement of the concave items in the rack. - Arrange crockery so that water does not collect in cavities.
Incorrect dosage the rinse aid.
-
-
Increase the dosage of rinse aid - see page 3, “Adding rinse aid”.
The rapid programme is intended for quickly washing lightly soiled dishes. If used for a full load of medium/
heavy soiled dishes, the dishes may not dry completely. If so, select a standard-length programme. For best
results, open the door after the end of the programme and wait 15 minutes before unloading the dishwasher.
-
Rapid programme selected.
...have discoloured plastic parts
-
Tomato sauce, for example, can lead to discolouring of plastic parts. Powder detergent is recommended as
it allows slightly higher doses to be used for improved whitening. Programmes with higher wash
temperatures should be used.
-
-
Tomato/Carrot juice.
...opaque glasses, etc
Dishes unsuitable for washing in dishwashers
(porcelain),
-
-
Only use dishwasher-proof crockery and dishes.
...removable deposits on glasses
...glasses not sparkling
Dishes should be put together, to avoid touching each other. Do not put glassware together in baskets.
Use suitable programme for glass.
-
-
Usage of incorrect programmes for glasses.
Not conform of glasses to washing in dishwashers
(porcelain).
-
Some kinds of glass cannot be washed in the dishwasher.
...permanent deposits on glasses
-
Rainbow effect.
-
-
-
-
This phenomenon is irreversible. We recommend in future:
Change the control of system of dosage of softener.
Be careful – follow recommended detergent dosage.
For combined action tablets see detergent producer’s recommendations.
...tea cups darken and dirt does not
disappear after washing in dishwasher
-
-
-
Not known.
-
-
This phenomenon is inevitable. Theine alters colours permanently.
...rust marks
...other marks
...streaks
Salty or acidic food residues can cause rust marks even on stainless steel cutlery. To avoid this, always use
the pre-wash programme if the dishes are to be washed later.
Pre-wash programme not used.
Rinse aid dosage too low.
-
-
-
In the presence of marks, increase the rinse aid dosage (see page 3, “Adding rinse aid”). If you use a
combined action detergent, try adding more rinse aid.
In the presence of streaks, reduce the rinse aid dosage (see page 3, “Adding rinse aid”). If you use a
combined action detergent which includes rinse aid, do not add any additional rinse aid.
-
-
Rinse aid dosage too high.
...suds
Unsuitable dosage of detergent/rinse aid.
Only use the amount of detergent/rinse aid required, since excessive amounts can lead to excess suds.
GB -7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnect the mains plug
What to do if...
If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap.
Contact the After-sales Service (see warranty).
Before contacting our After-Sales Service, take note of the following:
- the description of the fault,
- the appliance type and model,
- the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:
Precautions and general recommendations
1. Packing
-
-
Before cleaning or carrying out maintenance, disconnect the mains plug and turn off the water tap; also in
the event of any malfunction.
Repairs and technical modifications must be carried out exclusively by a qualified technician.
The packaging materials are 100% recyclable and marked with the recycling symbol
.
2. Removing the packaging and inspecting the contents
After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt,
contact a qualified technician or your local retailer.
7. Resistance to frost
If the appliance is placed in surroundings exposed to the risk of frost, it must be drained completely. Turn off
the water tap, remove the inlet and outlet hoses, and let all the water drain away. Make sure there is at least
1 kg of dissolved regeneration salt in the salt reservoir, to protect the appliance from temperatures of up to
-20°C. When the programme resumes, an error message may be displayed. “F1”/START indicator flashes
once: pour half a litre of warm water into the bottom of the dishwasher. “F6”/START indicator flashes 6
times: the appliance must remain at an ambient temperature of min. 5°C for at least 24 hours. After
eliminating these faults, RESET the appliance (see chapter “What to do if...”).
3. Before using the dishwasher for the first time
-
-
The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may
leave slight drips/water marks which will disappear with the first wash.
4. Energy and water savings
-
-
-
Do not rinse crockery under running water.
8. Disposal
Always fully load the dishwasher before running it or select the “Half load/Multizone” option (if available).
If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating
systems, the appliance may be connected to the hot water mains up to a maximum temperature of 60°C.
Make sure the water inlet hose is of the correct type (“70°C Max” or “90°C Max”).
-
The appliance is manufactured using recyclable materials. If you decide to scrap the dishwasher, it must be
disposed of in compliance with local waste disposal regulations. Make it unusable by cutting off the power
cord. To prevent situations of potential danger to children (e.g. danger of suffocation), break the lock of the
door so that it can no longer be closed.
5. Child safety
-
This appliance is marked according to the European directive 2002/96/CE on Waste Electrical and
Electronic Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent
potentially damaging consequences for the environment and health. Unsuitable disposal of an appliance of
-
-
-
Keep the packaging materials out of the reach of children.
Children must not be allowed to play with the dishwasher.
Store the detergent, rinse aid and salt out of the reach of children.
this type as household waste could have detrimental effects on the environment. The symbol
on the
6. Safety warnings
appliance, or on documentation enclosed with the appliance, indicates that this product must not be
treated as household waste, but must be delivered to the nearest collection centre for the recycling of
electrical and electronic appliances. Disposal must be carried out in accordance with local environmental
regulations for waste disposal. For further information on the treatment, recovery and recycling of this
appliance, contact your competent local authority, the collection service for household waste or the shop
where you purchased the appliance.
-
The appliance is not intended for use by children or physically or mentally impaired persons, unless
adequately supervised by a responsible adult capable of guaranteeing safe use of the appliance.
Do not operate the appliance in the open air.
Do not store flammable materials in close proximity to the dishwasher.
The water in the dishwasher is not potable.
Do not use solvents inside the dishwasher: risk of explosion!
Be careful when the door is open: risk of tripping!
The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest
objects on the open door or sit or stand on it.
-
-
-
-
-
-
EC Declaration of conformity
This appliance has been designed, constructed and distributed in compliance with the safety requirements of
EC Directives:
2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive).
Loading Capacity: 12 place settings.
-
Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end
facing downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp
end facing away from the front of the appliance.
We reserve the right to make technical modifications.
GB -8-
Download from Www.Somanuals.com. All Manuals Search And Download.
|