®
TM
ELECTRONIC
ELECTRIC DRYER
Use & Care Guide
For questions about features, operation/performance, parts accessories
or service call: 1-800-253-1301
or visit our website at... www.whirlpool.com
Table of Contents ................................................ 2
3979274B
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic
precautions, including the following:
I
I
Read all instructions before using the dryer.
I
Do not repair or replace any part of the dryer or
attempt any servicing unless specifically recom-
mended in this Use and Care Guide or in published
user-repair instructions that you understand and have
the skills to carry out.
Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
I
I
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
I
Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
I
I
Do not allow children to play on or in the dryer.
Close supervision of children is necessary when
the dryer is used near children.
I
I
Clean lint screen before or after each load.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
Before the dryer is removed from service or dis-
carded, remove the door to the drying compart-
ment.
Do not reach into the dryer if the drum is moving.
Do not install or store the dryer where it will be
exposed to the weather.
I
I
I
I
See installation instructions for grounding require-
ments.
I
Do not tamper with controls.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts needed
Check local codes. Check existing electrical supply and venting.
See “Electrical Requirements” and “Venting Requirements”
before purchasing parts.
INSTALLATION
INSTRUCTIONS
I
For close-clearance installations between 31.5 in. (80.01 cm)
and 37 in. (93.98 cm), see “Plan Vent System” section for
venting requirements.
Tools and Parts
Check that you have everything necessary for correct installation.
Proper installation is your responsibility.
I
I
Flat-blade screwdriver
I
I
I
Safety glasses
Vent clamps
Adjustable wrench that
opens to 1 in. (2.5 cm) or
hex-head socket wrench
(for adjusting dryer feet)
Caulking gun and
compound (for installing
new exhaust vent)
Mobile home installations require metal exhaust system hardware
available for purchase from the dealer from whom you purchased
your dryer. For further information, please refer to the “Assistance
or Service” section of this manual.
I
I
Level
I
I
Gloves
Wire stripper (direct wire
installations)
Tin snips (new vent
installations)
I
#2 Phillips screwdriver
Optional Pedestal
I
¼ in. nut driver
Are you placing the dryer on a pedestal? You may purchase a
pedestal separately for this dryer. This pedestal will add about
13 in. (33 cm) to the height of your unit for a total height of
approximately 51 in. (130 cm).
Parts supplied
Remove parts packages from dryer drum. Check that all parts are
included.
I
Door Reversal Kit
Optional pedestal
I
Parts package.
To order, call the dealer from whom you purchased your dryer or
refer to the “Assistance or Service” section of this manual. Ask
for Part Number LAB2700LQ (White) or LAB2700LT (Biscuit).
4 Leveling legs
NOTE: Do not use leveling legs if installing the dryer on a
pedestal.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation clearances
I
I
I
I
I
The location must be large enough to fully open the dryer
door.
Location Requirements
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door and
floor moldings.
Additional spacing of 1 in. (2.5 cm) on all sides of the dryer is
recommended to reduce noise transfer.
Companion appliance spacing should also be considered.
Dryer Dimensions
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the
floor for a garage installation.
Failure to do so can result in death, explosion,
or fire.
You will need
I
A location that allows for proper exhaust installation. See
“Venting Requirements.”
*
I
I
A separate 30 amp circuit.
A grounded electrical outlet located within 2 ft (61 cm) of
either side of the dryer. See “Electrical Requirements.”
*Most installations require a minimum 5½ in. (14 cm) clearance
behind the dryer for the exhaust vent with elbow. See “Venting
Requirements.”
I
I
A sturdy floor to support the total dryer weight of 200 lbs
(90.7 kg). The combined weight of a companion appliance
should also be considered.
A level floor with a maximum slope of 1 in. (2.5 cm) under
entire dryer. If slope is greater than 1 in. (2.5 cm), install
Extended Dryer Feet Kit, Part No. 279810. Clothes may not
tumble properly and automatic sensor cycles may not
operate correctly if dryer is not level.
Minimum installation spacing for custom undercounter
installation
The dimensions shown are for the minimum spacing allowed.
Custom undercounter installation - Dryer only
I
For a garage installation, you will need to place the dryer at
least 18 in. (46 cm) above the floor. If using a pedestal, you
will need an additional 6 in. (15.24 cm).
Do not operate your dryer at temperatures below 45ºF (7ºC). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
Install the dryer where it is protected from water and/or weather.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum installation spacing for recessed or closet
installation, with or without a pedestal
Minimum installation spacing for cabinet installation
I
I
The dimensions shown are for the minimum spacing allowed.
I
I
The dimensions shown are for the minimum spacing allowed.
For cabinet installation, with a door, minimum ventilation
openings in the top of the cabinet are required.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
7" (17.8 cm)
7" (17.8 cm)
Closet installation - Dryer only
"
"
"
"
"
9"
(22.9 cm)
"
"
"
"
0"
31¹ꢀ₂"
0"
0"
27"
0"
(0 cm) (80.0 cm) (0 cm) (0 cm) (68.6 cm) (0 cm)
Mobile home-additional installation requirements
This dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280).
1. Side view- closet or confined area
2. Closet door with vents
Recessed or closet installation - Dryer on pedestal
Mobile home installations require:
I
Metal exhaust system hardware which is available for
purchase from your dealer.
I
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
1. Recessed area
2. Side view - closet or confined area
6
Download from Www.Somanuals.com. All Manuals Search And Download.
If your outlet looks like this:
Electrical Requirements
It is your responsibility
I
To contact a qualified electrical installer.
I
To be sure that the electrical connection is adequate and in
conformance with the National Electrical Code, ANSI/NFPA
70-latest edition and all local codes and ordinances.
3-wire receptacle (10-30R)
Then choose a 3-wire power supply cord with ring or spade
terminals and UL approved strain relief. The 3-wire power supply
cord, at least 4 ft (1.22 m) long, must have 3, No.-10 copper wires
and match a 3-wire receptacle of NEMA Type 10-30R.
A copy of the above code standards can be obtained from:
National Fire Protection Association, Batterymarch Park,
Quincy, MA 02269.
I
To supply the required 3 or 4 wire, single phase, 120/240-volt,
60-Hz., AC-only electrical supply (or 3 or 4 wire, 120/208-volt
electrical supply, if specified on the serial/rating plate) on a
separate 30-amp circuit, fused on both sides of the line. A
time-delay fuse or circuit breaker is recommended. Connect
to an individual branch circuit. Do not have a fuse in the
neutral or grounding circuit.
If connecting by direct wire:
Power supply cable must match power supply (4-wire or 3-wire)
and be:
I
Flexible armored cable or non-metallic sheathed copper
cable (with ground wire), protected with flexible metallic
conduit. All current-carrying wires must be insulated.
I
I
Do not use an extension cord.
I
I
10 gauge solid copper wire (do not use aluminum).
At least 5 ft (1.52 m) long.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Electrical Connection
For a grounded, cord-connected dryer:
To properly install your dryer, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
This dryer must be grounded. In the event of malfunction
or breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current. This
dryer uses a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and ground-
ed in accordance with all local codes and ordinances.
I
I
I
If local codes do not permit the connection of a cabinet
ground connector to the neutral wire, see “Optional 3-wire
connection” section.
This dryer is manufactured with a 3-wire, cabinet-ground
conductor connected to the NEUTRAL (white or center wire)
of the wiring harness at the terminal block.
For a permanently connected dryer:
This dryer must be connected to a grounded metal, permanent
wiring system, or an equipment-grounding conductor must be
run with the circuit conductors and connected to the equip-
ment-grounding terminal or lead on the dryer.
Use a 4-wire conductor cord when the dryer is installed in a
mobile home or an area where local codes do not permit
grounding through the neutral.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the dryer is proper-
ly grounded. Do not modify the plug on the power supply cord:
if it will not fit the outlet, have a proper outlet installed by a
qualified electrician.
If using a power supply cord:
Use a UL approved power supply cord kit marked for use with
clothes dryers. The kit should contain:
I
A UL approved 30 amp power supply cord, rated 120/240
volt minimum. The cord should be type SRD or SRDT and be
at least 4 ft (1.22 m) long. The wires that connect to the dryer
must end in ring terminals or spade terminals with upturned
ends.
I
A UL approved strain relief.
If your outlet looks like this:
4-wire receptacle (14-30R)
Then choose a 4-wire power supply cord with ring or spade
terminals and UL approved strain relief. The 4-wire power supply
cord, at least 4 ft (1.22 m) long, must have 4, 10 gauge solid
copper wires and match a 4-wire receptacle of NEMA Type
14-30R. The ground wire (ground conductor) may be either green
or bare. The neutral conductor must be identified by a white
cover.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Power Supply Cord
Direct Wire
Fire Hazard
Fire Hazard
Use a new UL approved 30 amp power
supply cord.
Use 10 gauge solid copper wire.
Use a UL approved strain relief.
Use a UL approved strain relief.
Disconnect power before making electrical
connections.
Disconnect power before making electrical
connections.
Connect neutral wire (white or center wire) to
center terminal (silver).
Connect neutral wire (white or center wire) to
center terminal (silver).
Ground wire (green or bare wire) must be
connected to green ground connector.
Ground wire (green or bare wire) must be
connected to green ground connector.
Connect remaining 2 supply wires to remaining
2 terminals (gold).
Connect remaining 2 supply wires to remaining
2 terminals (gold).
Securely tighten all electrical connections.
Securely tighten all electrical connections.
Failure to do so can result in death, fire, or
electrical shock.
Failure to do so can result in death, fire, or
electrical shock.
3. Assemble a ³⁄₄ in. (1.9 cm) UL approved strain relief (UL
marking on strain relief) into the hole below the terminal block
opening. Tighten strain relief screws just enough to hold the
two clamp sections together. Put power supply cord through
the strain relief. The strain relief should have a tight fit with the
dryer cabinet and be in a horizontal position.
1. Disconnect power.
2. Remove the hold-down screw and terminal block cover.
4. Now complete installation following instructions for your type
of electrical connection:
4-wire (recommended)
3-wire (if 4-wire is not available)
1. Terminal block cover and hold-down screw
2. External ground connector
3. Neutral grounding wire (green/yellow)
4. Center, silver-colored terminal-block screw
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection Options
1. Remove center terminal block screw.
2. Remove appliance ground wire (green with yellow stripes)
from external ground connector screw. Fasten it under center,
silver colored terminal block screw.
If your home has:
And you will be
connecting to:
Go to Section
4-wire receptacle
(NEMA Type 14-30R)
A UL listed,
120/240 volt
minimum, 30
amp, dryer
power supply
cord*
4-wire connection:
Power supply cord
1
2
3
4-wire direct
A fused
4-wire connection:
Direct Wire
disconnect or
circuit breaker
box*
5"
1. External ground connector - Dotted line shows position
of NEUTRAL ground wire before being moved to center
terminal block screw
(12.7 cm)
2. Center silver-colored terminal block screw
3. Green/yellow wire of harness
3-wire receptacle
(NEMA type 10-30R)
A UL listed,
120/240 volt
minimum, 30
amp., dryer
power supply
cord*
3-wire connection:
Power supply cord
3. Connect ground wire (green or bare) of power supply cord to
external ground conductor screw. Tighten screw.
4. Connect neutral wire (white or center wire) of power supply
cord under center screw of the terminal block.
3-wire direct
A fused
3-wire connection:
Direct Wire
4
disconnect or
circuit breaker
box*
1
31/2"
(8.9 cm)
2
*If local codes do not permit the connection of a frame-
grounding conductor to the neutral wire, go to “Optional
3-wire Connection” section.
3
5
6
4-wire connection: Power supply cord
IMPORTANT: A 4-wire connection is required for mobile homes
and where local codes do not permit the use of 3-wire
connections.
1. External ground connector
2. Green or bare copper wire of power supply cord
3. ³⁄₄ in. (1.9 cm) UL-listed strain relief
4. Center silver-colored terminal block screw
5. Neutral grounding wire (green/yellow)
6. Neutral wire (white or center wire)
2
6
1
5. Connect the other wires to outer terminal block screws.
5
3
4
7
Tighten screws.
1. 4-wire receptacle (NEMA type 14-30R)
2. 4-prong plug
6. Tighten strain relief screws.
3. Ground prong
4. Neutral prong
7. Insert tab of terminal block cover into slot of dryer rear panel.
5. Spade terminals with upturned ends
6. ¾ in. (1.9 cm) UL approved strain relief
7. Ring terminals
Secure cover with hold-down screw.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place the hooked ends of the other power supply cable wires
under the outer terminal block screws (hooks facing right).
Squeeze hooked ends together. Tighten screws.
4-wire connection: Direct wire
IMPORTANT: A 4-wire connection is required for mobile homes
and where local codes do not permit the use of 3-wire
connections.
Direct wire cable must have 5 ft (1.52 m) of extra length so dryer
can be moved if needed.
Strip 5 in. (12.7 cm) of outer covering from end of cable, leaving
bare ground wire at 5 in. (12.7 cm). Cut 1¹⁄₂ in. (3.8 cm) from 3
remaining wires. Strip insulation back 1 in. (2.5 cm). Shape ends
of wires into a hook shape.
6. Tighten strain relief screws.
7. Insert tab of terminal block cover into slot of dryer rear panel.
Secure cover with hold-down screw.
3-wire connection: Power supply cord
Use where local codes permit connecting cabinet-ground
conductor to neutral wire.
2
4
5
When connecting to the terminal block, place the hooked end of
the wire under the screw of the terminal block (hook facing right),
squeeze hooked end together and tighten screw. See example
below.
1
3
7
6
1. 3-wire receptacle (NEMA type 10-30R)
2. 3-wire plug
3. Neutral prong
4. Spade terminals with up turned ends
5. ³⁄₄ in. (1.9 cm) UL approved strain relief
6. Ring terminals
1. Remove center terminal block screw.
2. Remove appliance ground wire (green with yellow stripes)
from external ground connector screw. Fasten it under center,
silver colored terminal block screw.
7. Neutral (white or center wire)
1. Loosen or remove center terminal block screw.
2. Connect neutral wire (white or center wire) of power supply
cord to the center, silver colored terminal screw of the
terminal block. Tighten screw.
3. Connect ground wire (green or bare) of power supply cable to
external ground conductor screw. Tighten screw.
4
1
2
3
3
1
2
4
5
5
6
1. External ground connector
1. External ground connector
2. Green or bare copper wire of power supply cord
3. ³⁄₄ in. (1.9 cm) UL-listed strain relief
2. Neutral grounding wire (green/yellow)
3. Center silver-colored terminal block screw
4. Neutral wire (white or center wire)
5. ³⁄₄ in. (1.9 cm) UL-listed strain relief
4. Center silver-colored terminal block screw
5. Neutral grounding wire (green/yellow)
6. Neutral wire (white or center wire)
3. Connect the other wires to outer terminal block screws.
4. Place the hooked end of the neutral wire (white wire) of power
supply cable under the center screw of terminal block (hook
facing right). Squeeze hooked end together. Tighten screw.
Tighten screws.
4. Tighten strain relief screws.
5. Insert tab of terminal block cover into slot of dryer rear panel.
Secure cover with hold-down screw.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Tighten strain relief screws.
3-wire connection: Direct wire
5. Insert tab of terminal block cover into slot of dryer rear panel.
Secure cover with hold-down screw.
Use where local codes permit connecting cabinet-ground
conductor to neutral wire.
Optional 3-wire connection
Direct wire cable must have 5 ft (1.52 m) of extra length so dryer
can be moved if needed.
Use for direct wire or power supply cord where local codes
do not permit connecting cabinet-ground conductor to
neutral wire.
Strip 3¹⁄₂ in. (8.9 cm) of outer covering from end of cable. Strip
insulation back 1 in. (2.5 cm). If using 3-wire cable with ground
wire, cut bare wire even with outer covering. Shape ends of wires
into a hook shape.
1. Remove center terminal block screw.
2. Remove appliance ground wire (green with yellow stripes)
from external ground connector screw. Connect appliance
ground wire and the neutral wire (white or center wire) of
power supply cord/cable under center, silver colored terminal
block screw. Tighten screw.
3. Connect the other wires to outer terminal block screws.
Tighten screws.
When connecting to the terminal block, place the hooked end of
the wire under the screw of the terminal block (hook facing right),
squeeze hooked end together and tighten screw. See example
below.
4. Tighten strain relief screws.
5. Insert tab of terminal block cover into slot of dryer rear panel.
Secure cover with hold-down screw.
1. Loosen or remove center terminal block screw.
6. Connect a separate copper ground wire from the external
ground connector screw to an adequate ground.
2. Place the hooked end of the neutral wire (white or center wire)
of power supply cable under the center screw of terminal
block (hook facing right). Squeeze hooked end together.
Tighten screw.
1
2
3
1
3
4
4
5
2
1. External ground connector
2. Neutral grounding wire (green/yellow)
3. Center silver-colored terminal block screw
4. Neutral wire (white or center wire)
5. ³⁄₄ in. (1.9 cm) UL-listed strain relief
1. External ground connector
2. Neutral grounding wire (green/yellow)
3. Neutral wire (white or center wire)
4. Grounding path determined by a qualified electrician
3. Place the hooked ends of the other power supply cable wires
under the outer terminal block screws (hooks facing right).
Squeeze hooked ends together. Tighten screws.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
An exhaust hood should cap the vent to prevent rodents and
insects from entering the home.
Venting Requirements
Exhaust hood must be at least 12 in. (30.5 cm) from the ground or
any object that is in the path of the exhaust (such as flowers,
rocks or bushes, etc.).
If using an existing vent system, clean lint from the entire length
of the system and make sure exhaust hood is not plugged with
lint. Replace any plastic or metal foil vent with rigid metal or
flexible metal vent.
Plan Vent System
Typical exhaust installations
Typical installations vent the dryer from the rear of the dryer.
Other installations are possible.
Fire Hazard
Use a heavy metal vent.
2
3
4
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in
death or fire.
1
5
6
WARNING: To reduce the risk of fire, this dryer MUST BE
7
EXHAUSTED OUTDOORS.
4 in. (10.2 cm) heavy metal exhaust vent and clamps must be
used. DURASAFE™ vent products are recommended.
8
DURASAFE™ vent products can be purchased from your dealer
or by calling Whirlpool Parts and Accessories. For more
information, see the “Assistance or Service” section of this
manual.
1. Dryer
2. Elbow
3. Wall
5. Clamps
6. Rigid metal or flexible metal vent
7. Vent length necessary to connect elbows
8. Exhaust outlet
4. Exhaust hood
I
The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, or a concealed space of a building.
Optional exhaust installations
This dryer can be converted to exhaust out the right side, left
side, or through the bottom.
I
I
Do not use an exhaust hood with a magnetic latch.
Do not install flexible metal vent in enclosed walls, ceilings or
floors.
I
Use clamps to seal all joints. Exhaust vent must not be
connected or secured with screws or other fastening devices
which extend into the interior of the duct. Do not use duct tape.
IMPORTANT: Observe all governing codes and ordinances.
Improper venting can cause moisture and lint to collect
indoors, which may result in:
Moisture damage to woodwork, furniture, paint, wall-
paper, carpets, etc.
Fire Hazard
Cover unused exhaust holes with one of the
following kits:
Housecleaning problems and health problems.
279818 (white)
Use a heavy metal vent. Do not use plastic or metal foil vent.
Rigid metal vent is recommended to prevent crushing and
kinking.
279925 (biscuit)
Contact your local dealer.
Flexible metal vent must be fully extended and supported when
the dryer is in its final position. Remove excess flexible metal vent
to avoid sagging and kinking that can result in reduced airflow
and poor performance.
Failure to follow these instructions can result in
death, fire, electrical shock, or serious injury.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Determine Vent Length
1. Select the route that will provide the straightest and most
direct path outdoors. Plan the installation to use the fewest
number of elbows and turns. When using elbows or making
turns, allow as much room as possible. Bend vent gradually
to avoid kinking. Avoid 90º turns.
1. Standard rear offset exhaust installation
2. Left or right side exhaust installation
3. Bottom exhaust installation (Not an option with
pedestal installations.)
2. Determine vent length.
Alternate installations for close clearances
The maximum length of the exhaust system depends upon:
Venting systems come in many varieties. Select the type best for
your installation. Two close-clearance installations are shown.
Refer to the manufacturer’s instructions.
I
I
I
The type of vent (rigid metal or flexible metal).
The number of elbows used.
The type of hood.
Recommended hood styles are shown here.
2
1
4"
(10.2 cm)
4"
(10.2 cm)
1. Over-The-Top installation (also available with one offset elbow)
2. Periscope installation
1. Louvered hood style
2. Box hood style
NOTE: The following kits for close clearance alternate
installations are available for purchase. Please see the
“Assistance or Service” section of this manual to order.
The angled hood style (shown following) is acceptable.
4"
I
Over-The-Top Installation:
Part Number 4396028
(10.2 cm)
I
Periscope Installation (For use with dryer vent to wall vent
mismatch):
2.5"
(6.4 cm)
Part Number 4396037 - 0 in. (0 cm) to 18 in. (45.72 cm)
mismatch
See the exhaust vent length chart that matches your hood
type for the maximum vent lengths you can use.
Part Number 4396011 - 18 in. (45.72 cm) to 29 in. (73.66 cm)
mismatch
Exhaust systems longer than specified will:
I
I
Shorten the life of the dryer.
Part Number 4396014 - 29 in. (73.66 cm) to 50 in. (127 cm)
mismatch
Reduce performance, resulting in longer drying times and
increased energy usage.
Special provisions for mobile home installations
3. Determine the number of elbows you will need.
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
IMPORTANT: Do not use vent runs longer than those
specified in the Vent Length Chart.
The following chart helps you determine your maximum vent
length based on the number of 90° turns or elbows you will
need and the type of vent (rigid or flexible metal) and hood
that you will use.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Vent Length Chart
2. Firmly grasp the body of the dryer (not the console panel).
Number of
90º turns
or elbows
Type of
vent
Box or
Louvered
hoods
Angled
hoods
0
1
2
3
4
Rigid metal
64 ft (20 m)
36 ft (11 m)
58 ft (17.7 m)
28 ft (8.5 m)
Flexible metal
Rigid metal
Flexible metal
54 ft (16.5 m)
31 ft (9.4 m)
48 ft (14.6 m)
23 ft (7 m)
Rigid metal
Flexible metal
44 ft (13.4 m) 38 ft (11.6 m)
27 ft (8.2 m) 19 ft (5.8 m)
Gently lay the dryer on the cardboard.
Rigid metal
Flexible metal
35 ft (10.7 m) 29 ft (8.8 m)
25 ft (7.6 m)
3. Examine the leveling legs. Find the diamond marking.
17 ft (5.2 m)
Rigid metal
Flexible metal
27 ft (8.2 m)
23 ft (7 m)
21 ft (6.4 m)
15 ft (4.6 m)
NOTE: Side and bottom exhaust installations have a 90º turn
inside the dryer. To determine maximum exhaust length, add 1
90º turn to the chart.
4. Screw the legs into the leg holes by hand. Use a wrench to
finish turning the legs until the diamond marking is no longer
visible.
5. Place a carton corner post under each of the 2 dryer back
corners. Stand the dryer up. Slide the dryer on the corner
posts until it is close to its final location. Leave enough room
to connect the exhaust vent.
Install Vent System
1. (Optional) Put on safety glasses and gloves.
2. Install exhaust hood. Use caulking compound to seal exterior
6. Once connection is made and dryer is in final location,
wall opening around exhaust hood.
remove corner posts and cardboard.
3. Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4 in. (10.2 cm)
clamp.
Level Dryer
Check the levelness of the dryer. Check levelness first
side-to-side, then front-to-back.
4. Run vent to dryer location. Use the straightest path possible.
See “Determine Vent Length.” Avoid 90º turns. Use clamps to
seal all joints. Do not use duct tape, screws or other fastening
devices that extend into the interior of the vent to secure
vent.
Install Leveling Legs
WARNING
If the dryer is not level, prop up the dryer using a wood block.
Use a wrench to adjust the legs up or down and check again for
levelness.
Excessive Weight Hazard
Use two or more people to move and install
dryer.
NOTE: It might be necessary to level the dryer again after it has
been moved into its final position.
Failure to do so can result in back or other injury.
1. To protect the floor, use a large flat piece of cardboard from
the dryer carton. Place cardboard under the entire back edge
of the dryer. See illustration.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the door
1. Open the dryer door. Remove the 5 screws that hold the door
hinge on the front panel of the dryer. Loosen, but do not
remove, the screw with the top keyhole opening LAST
(second from the top).
Connect Vent
1. Using a 4 in. (10.2 cm) clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure the vent is
clean. The dryer vent must fit over the dryer exhaust outlet
and inside the exhaust hood. Make sure the vent is secured
to exhaust hood with a 4 in. (10.2 cm) clamp.
2. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
3. (On gas models) Check to be sure there are no kinks in the
flexible gas line.
Reverse Door Swing
You can change your door swing from a right-side opening to a
left-side opening, if desired.
2. Lift and pull forward on the door so that the screwhead clears
Locate the door reversing kit that was shipped in the drum of
your dryer. You will need these parts to complete the door
reversal.
the keyhole. Remove the door.
3. Lay the dryer door on a flat, protected surface with the inside
door assembly facing up. Remove the 2 screws holding the
handle to the door. Pull handle straight out and set aside. A
new handle is provided.
Loosen door trim
1. Place a towel or soft cloth on top of the dryer or work space
to protect the surface.
2. Loosen the plastic trim above and below the handle filler.
Carefully pull out on the trim until it unsnaps. Remove the
handle filler and set aside.
1
NOTE: Keep this handle in case you decide to return the door
to its original position.
2
4. Remove the 6 screws to release the outer door assembly
from the inner door assembly (see illustration). It is important
that you remove ONLY the 6 indicated screws.
1. Plastic trim
2. Handle filler
3. Loosen the plastic trim above and below the hinge cover.
Carefully pull out on the trim until it unsnaps. Remove the
hinge cover and set aside.
1
5. Lift the inner door assembly off of the outer door assembly.
Set the outer door assembly aside.
2
1. Plastic trim
2. Hinge cover
Keep the original handle filler and hinge cover in case you
decide to return the door to its original position.
A new handle filler and hinge cover are provided in the door
reversing kit that will be installed in a later step.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Insert the new handle into the side opening of the door. Make
sure the handle seats all the way in, and the holes line up with
the holes in the door. Reattach with 2 screws.
Reverse the hinge and hinge bracket
1. Place the inner door, screwhead side up, on the work surface.
2. Remove the 4 screws that hold the hinge to the door.
5. Use a small flat-head screwdriver to remove hole plugs in the
door opening. Slide the head of the screwdriver under the
cap of each hole plug, being careful not to scratch the dryer
surface. Lift up. Remove the hole plugs in the door opening
and insert in the opposite side.
6. Insert a screw in the second opening from the top of the
hinge opening and partially tighten. Hang the door by placing
the top hinge keyhole over the second screwhead and tighten
the screw. By putting this screw in first, the door will hang in
place while you insert and tighten the remaining 4 screws.
3. Remove the 2 screws that hold the handle bracket to the
door.
Install new handle filler and hinge cover
4. Move hinge to the other side and reattach.
5. Move handle bracket to the other side and reattach.
6. Set the inner door assembly aside.
1. Using the new handle filler provided in the reversing kit, hook
the top of the handle filler onto the loosened upper door trim.
Snap the joined pieces into place. You may need to use the
heel of your hand to firmly snap the pieces back into place.
Reinstalling the door
1. Check for fingerprints on the glass. Clean if necessary.
2. Hook the bottom of the handle filler onto the lower door trim
and snap into place.
2. Place the inner door assembly into the outer door assembly.
Align the hinge in the opening on the side. To fit correctly, the
inside door assembly edge is completely inside the outside
door assembly edge.
3. Repeat steps 1 and 2 to install the hinge cover on the
opposite side.
4. Close the door and check that it latches securely.
3. Reassemble the inner and outer door assemblies with the 6
screws.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Complete Installation
1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
2. Check to be sure you have all of your tools.
3. Dispose of all packaging materials.
4. Check the dryer’s final location. Be sure the vent is not
crushed or kinked.
5. Check to be sure the dryer is level. (See “Level Dryer.”)
6. Plug into a grounded outlet. Turn power on.
7. Remove the blue protective film on the console and any tape
remaining on the dryer.
8. Read “Dryer Use.”
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
10. Set the dryer on a full heat cycle (not an air cycle) for 20
minutes and start the dryer.
If the dryer will not start, check the following:
I
I
I
I
I
Controls are set in a running or “On” position.
Start button has been pushed firmly.
Dryer is plugged into a grounded outlet.
Electrical supply is connected.
House fuse is intact and tight; or circuit breaker has not
tripped.
I
Dryer door is closed.
11. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat.
If you do not feel heat, turn the dryer off and check the
following:
I
There may be 2 fuses or circuit breakers for the dryer. Check
to make sure both fuses are intact and tight, or that both
circuit breakers have not tripped. If there is still no heat,
contact a qualified technician.
NOTE: You may notice a burning odor when the dryer is first
heated. This odor is common when the heating element is first
used. The odor will go away.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER USE
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
Starting Your Dryer
The following is a guide to starting your dryer. Please refer to
specific sections of this manual for more detailed information.
1. Clean lint screen before or after each cycle.
2. Place laundry into dryer and shut door. See “Loading.”
3. Rotate the dial to select either an Automatic or Manual Cycle
then press the CONTROL ON button. The preset settings and
drying time for the cycle chosen will be displayed.
To use an Automatic Cycle
I
I
Point the dial to an Automatic Cycle.
Explosion Hazard
Select DRYNESS LEVEL to adjust how dry you want the
load to be. The time displayed is an estimated length of
the cycle based on the Dryness Level selected. As the
cycle runs, the control senses the dryness of the load and
adjusts the time automatically for the selected Dryness
Level.
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in
death, explosion, or fire.
NOTE: Time is not adjustable for Automatic Cycles. Pressing
the More Time or Less Time buttons will cause a triple beep,
indicating that the time cannot be changed.
I
I
I
Press the WRINKLE SHIELD™ feature button if this
option is desired.
Press the END OF CYCLE SIGNAL button to set signal
volume to desired level.
Fire Hazard
No washer can completely remove oil.
Press (and hold) HOLD TO START button until dryer starts
(about 1 second).
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
Once an Automatic cycle has started, the WRINKLE
SHIELD™ feature and the End of Cycle Signal level can be
adjusted. Press the PAUSE/CANCEL key twice to stop the
dryer and clear the settings, allowing you to select another
cycle and Dryness Level.
Items containing foam, rubber, or plastic must be
dried on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in
death or fire.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
To use a Manual Cycle
Rotate the dial to select a Manual Cycle.
To unlock:
Press and hold the END OF CYCLE SIGNAL button for three
seconds to turn this feature off.
I
Press MORE TIME or LESS TIME until the desired drying time
is displayed. Tap MORE TIME or LESS TIME and the time will
change by 1-minute intervals. Press and hold MORE TIME or
LESS TIME and the time will change by 5-minute intervals.
The initial time displayed is the actual drying time.
NOTE: When the dryer is running and Control Locked is on, the
dryer can be stopped by pressing the Pause/Cancel button, but
can’t be restarted until the control is unlocked.
Loading
Properly loading your dryer can lower your utility bill and prolong
the life of your garments.
Loading suggestions
I
Load the dryer by the amount of space items take up, not by
their weight.
NOTE: The More Time or Less Time feature can be used only
I
Do not overload the dryer. This causes wrinkling and uneven
drying.
with Manual Cycles.
I
Press TEMPERATURE until the desired temperature
glows.
Super Capacity Plus Dryers
Heavy Work Clothes
NOTE: Pressing the Dryness Level button will cause the triple
beep indicating that this option is not selectable. Also, a
Dryness Level is not indicated.
4 jeans
4 workpants
4 workshirts
2 sweatpants
2 sweatshirts
I
I
I
Press the WRINKLE SHIELD™ feature button if this
option is desired.
Press the END OF CYCLE SIGNAL button to set volume
to desired level.
Towels
10 bath towels
10 hand towels
14 washcloths
Press (and hold) HOLD TO START button until dryer starts
(about 1 second).
While a Manual Cycle is running, you can change the settings
for Time, Temperature, the WRINKLE SHIELD™ feature, and
the End of Cycle Signal. Press the PAUSE/CANCEL key twice
to stop the dryer and clear the settings, allowing you to select
another cycle.
Mixed Load
3 sheets (1 king, 2 twin)
4 pillowcases
3 shirts
9 T-shirts
9 shorts
10 handkerchiefs
3 blouses
Stopping Your Dryer
Drying and Cycle Tips
To stop your dryer at any time
Select the correct cycle and dryness level or temperature for your
load. If an Automatic Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing
the dryness level of your load. If a Manual Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
Press PAUSE/CANCEL twice or open the door.
Pausing or Restarting
To pause the dryer at any time
Open the door or press PAUSE/CANCEL once.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
To restart the dryer
Close the door and press (and hold) HOLD TO START button until
dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
Drying tips
I
Follow care label directions when they are available.
I
If you use fabric softener sheets, use only ones labeled as
dryer safe. Follow package instructions.
I
I
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits, and synthetic fabrics.
Control Locked
This feature allows you to lock your settings to prevent
unintended use of the dryer. You can also use the Control Locked
feature to prevent unintended cycle or option changes during
dryer operation.
Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased
shrinkage or wrinkling.
To enable the Control Locked feature when dryer is
running:
Press and hold the END OF CYCLE SIGNAL button for three
seconds. The control is locked when a single beep is heard and
the Control Locked status light is on.
I
When the dryer is off, it is not necessary to press the Control
On button before activating the Control Locked feature.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Cycle tips
WRINKLE SHIELD™ Feature
The WRINKLE SHIELD feature light glows when this option is
selected. This indicator stays on with the Cycle Complete light.
I
Dry most loads using the preset cycle settings.
I
Refer to the Automatic or Manual Preset Cycle Settings chart
(in the “Cycles” section) for a guide to drying various loads.
Control Locked
The CONTROL LOCKED light glows when this option is enabled.
I
Drying temperature and Dryness Level are preset when
you choose an Automatic Cycle. You can choose a
different dryness level, depending on your load by
pressing the DRYNESS LEVEL button to select MORE or
LESS.
Indicator lights
Other indicator lights on the control panel show Cycle, Temper-
ature, and End of Cycle settings selected.
I
If you wish to adjust the cycle length of a Manual Cycle,
you must press MORE TIME or LESS TIME. Adjust the
temperature of a Manual Cycle by pressing
The time display will indicate the estimated or actual time
remaining in a cycle.
TEMPERATURE until the desired temperature is selected.
NOTE: You cannot choose a Dryness Level with Manual
Cycles
Cycles.
Select the drying cycle that matches the type of load you are
drying (see Automatic Preset or Manual Preset Cycle Settings
charts).
Status Lights
You may follow the progress of your dryer with the drying Status
indicator lights.
Cycle control knob
Automatic Cycles
Automatic Cycles allow you to match the cycle to the load you
are drying. See the following “Automatic Preset Cycle Settings”
chart. Each cycle dries certain fabrics at the recommended
temperature. A sensor detects the moisture in the load and
automatically adjusts the drying time for optimal drying.
Sensing
When the dryer is first turned on, the SENSING light glows until a
wet item is detected.
I
In an Automatic Cycle, if a wet item has not been detected
within 10 minutes, the Sensing light will turn off and the dryer
will shut down.
Heavy Duty
Use this cycle to get High heat for heavy fabrics such as cotton
towels or bedspreads.
I
In a Manual Cycle, if a wet item is not detected after 10
minutes the Wet light turns on and the selected cycle
continues.
Normal
Wet
Use this cycle to get Medium heat for drying sturdy fabrics such
as work clothes.
The WET light will turn on when a wet item has been detected in
the dryer. The Wet light will remain on until:
Casual
I
The damp dry point is reached in an Automatic Cycle.
The dryer enters the cool down period in a Manual Cycle.
Use this cycle to get Medium heat for drying no-iron fabrics, such
as sport shirts, casual business clothes and permanent press
blends.
I
Damp
The DAMP light indicates that the load has reached the damp dry
level.
Delicate
Use this cycle to get Low heat for drying synthetic fabrics,
washable knit fabrics and no-iron finishes.
NOTE: The Damp light is not used with manual cycles.
Cool Down
Super Delicate
Use this cycle to get Extra Low heat to gently dry items such as
lingerie, exercise wear, or sheer curtains.
The COOL DOWN light glows during the cool down part of the
cycle. Laundry is cooling down for ease in handling.
Cycle Complete
This light glows when a drying cycle is finished. If the WRINKLE
SHIELD™ feature has been selected, the WRINKLE SHIELD™
feature indicator light will also be on.
The Cycle Complete light turns off one hour after the end of a
drying cycle (including the WRINKLE SHIELD™ cycle of 2 hours),
when Pause/Cancel is pressed, or when the door is opened.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Preset Cycle Settings
Additional Features
WRINKLE SHIELD™ Feature
When you are unable to remove a load of clothes from the dryer
as soon as it stops, wrinkles can form. The WRINKLE SHIELD™
feature periodically tumbles, rearranges and fluffs the load to
avoid wrinkles.
Automatic Cycles
Load Type
Temp.
High
Time*
(Minutes)
HEAVY DUTY
Heavyweight, towels
40
34
36
28
NORMAL
Corduroys, work clothes
Medium
Medium
Low
I
I
I
Press the WRINKLE SHIELD™ feature to get up to 120
minutes of heat-free, periodic tumbling at the end of a cycle.
CASUAL
Permanent press, synthetics
Stop at any time by pressing the WRINKLE SHIELD™ feature
or opening the dryer door.
For the Casual Cycle, the WRINKLE SHIELD™ feature is
preset to “On.” The other Automatic Cycles will retain the
WRINKLE SHIELD™ feature setting. (For example, if you
select the WRINKLE SHIELD™ feature in the Normal cycle,
the WRINKLE SHIELD™ feature will be on the next time you
select the Normal cycle.)
DELICATE
Lingerie, blouses, washable
woolens
SUPER DELICATE
Exercise wear, sheer curtains, lace
Extra Low
22
NOTE: If you do not select the WRINKLE SHIELD™ feature, the
dryer stops after the cool down period.
* Estimated Time with Dryness Level (medium) setting.
Temperature
Manual Cycles
Temperature settings are used with the Manual Cycles. Press
TEMPERATURE until the desired temperature setting glows.
Temperature settings cannot be used with the Automatic Cycles.
Use Manual Cycles to select a specific amount of drying time and
a drying temperature. When a Manual Cycle is selected, the
ESTIMATED TIME REMAINING display shows the actual time
remaining in your cycle. You can change the actual time in the
cycle by pressing MORE TIME or LESS TIME.
Timed Dry
Use this cycle to complete drying if items are still damp after an
Automatic Cycle. Timed Dry is also useful for drying heavyweight
and bulky items, such as bedspreads and work clothes.
Touch Up
Use this setting to remove wrinkles from items, such as clothes
packed in a suitcase or items wrinkled from being left in the dryer
too long.
Quick Dry
Use this cycle for drying small loads or loads that need a short
drying time.
Air Only
Use the Air Only setting for items that require drying without heat
such as rubber, plastic and heat-sensitive fabrics. This chart
shows examples of items that can be dried using Air Only.
Manual Preset Cycle Settings
Manual Cycles
Load Type
Temp.
Default Time
(Minutes)
Type of Load
Time*
(Minutes)
TIMED DRY
Heavyweight, bulk,
bedspreads, work clothes
High
40
Foam rubber - pillows, padded bras, stuffed
toys
20 - 30
TOUCH UP
Medium
High
20
27
Plastic - Shower curtains, tableclothes
Rubber-backed rugs
20 - 30
40 - 50
10 - 20
Remove wrinkles
QUICK DRY
Small loads
Olefin, polypropylene, sheer nylon
* Reset time to complete drying, if needed.
When using Air Only
I
I
I
Check to see that coverings are securely stitched.
Shake and fluff pillows by hand periodically during the cycle.
Dry item completely. Foam rubber pillows are slow to dry.
NOTE: Automatic Cycles are not available when using the Air
Only setting.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Put the wet items on top of the rack. Leave space between
End of Cycle Signal
the items so air can reach all the surfaces.
The End of Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end of
the cycle reduces wrinkling.
NOTE: Do not allow items to hang over the edge of the rack.
4. Close the door.
5. Select a timed drying cycle and temperature, or an air cycle.
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using the Air Only temperature setting.
Press and release the END OF CYCLE SIGNAL to adjust the
sound level or turn off the signal.
NOTE: When the WRINKLE SHIELD™ feature is selected and the
End of Cycle Signal is on, an audible sound will emit every five
minutes until the clothes are removed, or the WRINKLE
SHIELD™ feature is finished.
6. You must select a time by pressing MORE TIME or LESS
TIME. Reset time as needed to complete drying. Refer to the
following table.
7. Press (and hold) HOLD TO START button (about 1 second).
NOTE: You must remove rack for normal tumbling. Do not use
Drying Rack
automatic cycles with the drying rack.
The drying rack is useful for drying items you would not
necessarily want to tumble dry or that you would normally line dry
(for example, sweaters).
This chart shows examples of items that can be rack dried and
the suggested cycle, temperature setting and drying time. Actual
drying time will depend on the amount of moisture items hold.
To use the drying rack
Do not remove the lint screen.
1. Open dryer door.
Rack Dry
Setting
Temp
Time*
Wool Sweaters
Block to shape and lay flat on
the rack
Timed
Dry
Low
60
Stuffed toys or pillows
Timed
Dry
Low
N/A
N/A
60
90
90
Cotton or polyester fiber filled
Stuffed toys or pillows
Foam rubber filled
Air Only
(no heat)
1. Front edge
Sneakers or canvas shoes
Air Only
2. Place drying rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on
front edge of drying rack to secure over the lint screen.
(no heat)
*(Minutes) Reset time to complete drying, if needed.
1. Dryer back panel
22
Download from Www.Somanuals.com. All Manuals Search And Download.
As needed cleaning
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
DRYER CARE
Clean the lint screen with a nylon brush every 6 months, or more
frequently, if it becomes clogged due to a residue buildup.
Cleaning the Dryer Location
Keep dryer area clear and free from items that would obstruct the
flow of combustion and ventilation air.
To wash
1. Roll lint off the screen with your fingers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
Explosion Hazard
4. Rinse screen with hot water.
Keep flammable materials and vapors, such as
gasoline, away from dryer.
5. Thoroughly dry lint screen with a clean towel. Replace screen
in dryer.
Place dryer at least 18 inches (46 cm) above the
floor for a garage installation.
Cleaning the Dryer Interior
To clean dryer drum
Failure to do so can result in death, explosion,
or fire.
1. Make a paste with powdered laundry detergent and very
warm water.
2. Apply paste to a soft cloth.
Cleaning the Lint Screen
OR
3. Apply a liquid, non-flammable household cleaner to the
stained area and rub with a soft cloth until all excess dye is
removed.
Every load cleaning
The lint screen is located in the door opening of the dryer. Clean it
before or after each load. A screen blocked by lint can increase
drying time.
4. Wipe drum thoroughly with a damp cloth.
To clean
5. Tumble a load of clean cloths or towels to dry drum.
1. Pull the lint screen straight up. Roll lint off the screen with
your fingers. Do not rinse or wash screen to remove lint. Wet
lint is hard to remove.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and will
not stain future loads of clothes. Dry unstable dye items inside
out to prevent dye transfer.
Removing Accumulated Lint
From Inside the Dryer Cabinet
Lint should be removed every 2 years or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
2. Push the lint screen firmly back into place.
IMPORTANT:
From the Exhaust Vent
Lint should be removed every 2 years, or more often, depending
on dryer usage.
I
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
I
Some towels made of synthetic fibers and natural fibers
(polyester and cotton blends) may shed more lint than other
towels, causing your dryer’s lint screen to fill up faster. Be
sure to remove lint from the lint screen before and after drying
new towels.
I
If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint. (See “Venting
Requirements.”)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Vacation and Moving Care
TROUBLESHOOTING
Vacation care
Operate your dryer only when you are at home. If you will be on
vacation or not using your dryer for an extended period of time,
you should:
First try the solutions suggested here and possibly avoid
the cost of a service call...
1. Unplug dryer or disconnect power.
2. Wash lint screen.
Dryer displaying code message
I
I
“PF” (power failure), check the following:
Was the drying cycle interrupted by a power failure?
Press (and hold) HOLD TO START button to restart the dryer.
Moving care
1. Unplug dryer or disconnect power. Disconnect wiring if dryer
is direct wired.
“E” Variable (E1, E2, E3) service codes:
Call for service.
2. Make sure leveling legs are secure in dryer base.
3. Use masking tape to secure dryer door.
Clothes are not drying satisfactorily
Changing the Drum Light
I
Check the following:
Is the lint screen clogged with lint?
The dryer light automatically turns on inside the dryer drum when
you open the door.
Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for 5-10 minutes.
Hold your hand under the outside exhaust hood to check air
movement. If you do not feel air movement, clean exhaust
system of lint or replace exhaust vent with heavy metal or
flexible metal vent. (See “Installation Instructions.”)
To change the drum light
1. Unplug dryer or disconnect power.
2. Open the dryer door. Locate the light bulb cover on the back
wall of the dryer. Remove the screw located in the lower right
corner of the cover. Remove the cover.
Is the exhaust vent crushed or kinked? Replace with a heavy
metal vent. (See “Installation Instructions.”)
3. Turn bulb counterclockwise. Replace the bulb with a 10-watt
appliance bulb only. Replace the cover and secure with the
screw.
Has a fuse blown, or a circuit breaker tripped? Electric dryers
use 2 household fuses or breakers. The drum may be turning,
but you may not have heat.
4. Plug in dryer or reconnect power.
Has an air cycle been selected? Select the right cycle for the
types of garments being dried (see “Cycles”).
Is the automatic cycle ending early? The load may not be
contacting the electronic sensor strips, level the dryer.
Are fabric softener sheets blocking the grille? Use only one
fabric softener sheet and only use it once.
I
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
I
I
Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water
and with items that hold moisture (cottons).
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer will not run
Items shrinking
I
Check the following:
I
I
Was the dryer overloaded?
Is the power cord plugged in?
Dry smaller loads that can tumble freely.
Has a fuse blown, or has circuit breaker tripped?
Was a regular fuse used? Use a time-delay fuse.
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type (see “Cycles”).
Is the dryer door firmly closed? If not, the time display will
blink.
Loads are wrinkled
Was HOLD TO START firmly pressed and held for at least 1
second?
I
I
Was load removed from dryer at the end of the cycle?
Is a cycle selected?
Was dryer overloaded?
Dry smaller loads that can tumble freely.
Unusual sounds
I
Did load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type (see “Cycles”).
I
Has the dryer had a period of non-use?
If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.
Odors
Lint on load
I
I
Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, re-wash and dry the clothing.
I
I
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Is load properly sorted?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
Is the dryer being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
I
I
Is the load too big or too heavy?
Garment damage
Dry smaller loads so lint can be carried to the lint screen.
Was the load overdried?
Use correct dryer settings for load type (see “Cycles”).
Overdrying can cause lint-attracting static electricity.
I
Check the following:
Were zippers, snaps, and hooks left open?
Were strings and sashes tied to prevent tangling?
Were care label instructions followed?
Were items damaged before drying?
I
I
Was paper or tissue left in pockets?
Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and
laundering.
Stains on load or color change
I
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle
when the load is cold. Do not add fabric softener sheets to a
warm load.
I
I
Were items soiled when placed in the dryer?
Items should be clean before being dried.
Were items properly sorted?
Sort light colors from dark colors. Sort colorfast items from
noncolorfast items.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only FSP® factory specified parts. These parts will fit right
and work right because they are made with the same precision
used to build every new WHIRLPOOL® appliance. To locate FSP®
replacement parts in your area, call our Customer Interaction
Center telephone number or your nearest designated service
center.
For assistance and service
Call the Whirlpool Customer Interaction Center toll free:
1-800-253-1301.
Our consultants provide assistance with:
I
I
I
I
I
Features and specifications on our full line of appliances
Installation information
Use and maintenance procedures
Accessory and repair parts sales
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.)
I
Referrals to local dealers, repair parts distributors, and
service companies
Whirlpool designated service technicians are trained to fulfill the
product warranty and provide after-warranty service, anywhere in
the United States.
To locate the Whirlpool designated service company in your area,
you can also look in your telephone directory Yellow Pages.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Whirlpool Corporation
Customer Interaction Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Accessories U.S.A.
To order accessories, call the Whirlpool Customer Interaction
Center toll free at 1-800-442-9991 and follow the menu prompts.
Accessories Online.”
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
27
Download from Www.Somanuals.com. All Manuals Search And Download.
WHIRLPOOL® DRYER WARRANTY
ONE YEAR FULL WARRANTY
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor to correct defects in materials or
workmanship. Service must be provided by a Whirlpool designated service company.
SECOND YEAR LIMITED WARRANTY ON ELECTRONIC CONTROL BOARDS
In the second year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation will pay for FSP® replacement parts to replace the electronic control boards if
defective in materials or workmanship.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON PORCELAIN TOP
In the second through fifth years from the date of purchase, when this dryer is operated and maintained according to instructions
attached to or furnished with the product, Whirlpool Corporation will pay for FSP replacement parts to replace the porcelain top should
it chip or rust due to defective materials or workmanship.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your dryer, including venting. Heavy 4 in. (10.2 cm) metal exhaust vent must be used. Refer
to the venting section of this manual and your Installation Instructions.
2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to
replace owner accessible light bulbs.
3. Repairs when your dryer is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Corporation.
5. Replacement parts or repair labor costs for units operated outside the United States.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Any labor costs incurred during the Limited Warranty periods.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Outside the 50 United States, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if another
warranty applies.
If you need service, first see “Troubleshooting.” Additional help can be found by checking “Assistance or Service,” or by calling our
Customer Interaction Center at 1-800-253-1301, from anywhere in the U.S.A. or write: Whirlpool Corporation, Customer Interaction
Center, 553 Benson Road, Benton Harbor, MI 49022-2692.
1/02
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Write down the following information about your dryer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number.
You can find this information on the model and serial number
label, located at the top inside dryer door well.
3979274B
© 2002 Whirlpool Corporation.
9/02
Printed in U.S.A.
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|