Wharfedale Portable Speaker SVP 10 User Manual

Model name  
SVP-10  
65-20kHz  
90 X 60  
SVP-12  
50-20kHz  
90 X 60  
SVP-12M  
50 - 20kHz  
90 X 60  
SVP-15  
45-20kHz  
90 X 60  
SVP-215  
40-20kHz  
90 X 60  
SVP-15B  
SVP-18B  
SVP SERIES PROFESSIONAL SPEAKER USER MANUAL  
FREQ RESP +/- 3 DB  
COVERAGE (H X V)  
45-250Hz  
40-250Hz  
SVP-10 • SVP-12 • SVP-12M • SVP-15 • SVP-215 •  
SVP-15B • SVP-18B  
POWER HANDLING (Watts)  
Continuous  
Music  
peak  
100  
200  
400  
150  
300  
600  
150  
300  
600  
200  
400  
800  
250  
500  
1000  
250  
500  
1000  
300  
600  
1200  
SENSITIVITY 1W@1M  
PEAK SPL  
96dB  
121.5dB  
8  
97dB  
124.5dB  
8Ω  
97dB  
124.5dB  
8Ω  
98dB  
126dB  
8Ω  
101dB  
129.5dB  
4Ω  
98dB  
126.5dB  
8Ω  
99dB  
129.5dB  
8Ω  
ƽ WARNING & SAFETY INSTRUCTIONS  
SYSTEM IMPEDANCE  
L F DRIVER SIZE  
Driver size  
1. READ INSTRUCTIONS carefully before operating this product.  
RETAIN these instructions.  
5. CABLES - Never use shielded or microphone cable for any speak-  
er connection as this will not be heavy enough to handle the amplifier  
load and could cause damage to the complete system.  
10”  
12”  
12”  
15”  
15”  
15”  
18”  
2.  
Coil Size (mm/ins)  
HF SECTION  
39/1.5”  
51/2”  
51/2”  
51/2”  
38/1.5”  
65/2.5”  
75/3”  
3. COMPLY WITH WARNINGS - All warnings and instructions for this  
product should be adhered to.  
6. ƽ ꢀ RIGGING • SUSPENDING • MOUNTING  
Coil Size (mm/ins)  
Exit Size (mm/ins)  
HF Protection  
25 / 1”  
30/1.2”  
Bulb  
25 / 1”  
30/1.2”  
Bulb  
25 / 1”  
30/1.2”  
Bulb  
25 / 1”  
30/1.2”  
Bulb  
25 / 1”  
30/1.2”  
Bulb  
-
-
-
-
-
-
-
-
The rigging, suspension or mounting of this speaker system can  
expose members of the public to serious health risks and even death.  
UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND OR  
OTHERWISE MOUNT THIS SYSTEM UNLESS YOU ARE FULLY  
QUALIFIED AND CERTIFIED TO DO SO BY RELEVANT LOCAL,  
STATE AND NATIONAL AUTHORITIES. ALL RELEVANT SAFETY  
REGULATIONS MUST BE FOLLOWED. IF YOU ARE NOT PROP-  
ERLY QUALIFIED OR DO NOT KNOW OF PERTINENT REGULA-  
TIONS, CONSULT QUALIFIED PERSONNEL FOR ADVICE AND  
ASSISTANCE.  
4. USE WITH AMPLIFIERS - In order to avoid damage, it is advis-  
able to establish and follow a pattern for turning on and off any sound  
system. With all system parts connected, turn on source equipment,  
tape decks, instruments, mixers, signal processors etc., BEFORE  
turning on your power amplifier. Many products output turn on and  
turn off transients that can damage speakers. By turning on your  
power amplifier LAST and making sure the amplifier’s input controls  
are at minimum any transients “upstream” of the amplifier are not  
amplified and passed to the speaker. Wait until all system parts have  
stabilised, then bring up amplifier controls to operating level. This  
should take no more than a few seconds. Similarly when shutting  
systems down, always turn down amplifier input controls and then  
turn off your amplifier BEFORE shutting down other components.  
Professional amplifiers often feature delayed turn on/off circuits to  
perform these functions for you automatically.  
HF HORN  
Elliptical  
Elliptical  
Elliptical  
Elliptical  
Elliptical  
CROSSOVER SECTION:  
Crossover frequency  
High Pass Out  
3.2k  
No  
3.2k  
No  
3.2k  
No  
3.2k  
No  
3.2k  
No  
150Hz/6dB  
150Hz/6dB  
150Hz/6dB  
150Hz/6dB  
ENCLOSURE TYPE  
Shape  
Trapezoid  
Carpet/Black  
Yes  
Trapezoid  
Carpet/Black  
Yes  
Floor monitor  
Carpet/Black  
No  
Trapezoid  
Carpet/Black  
Yes  
Trapezoid  
Carpet/Black  
No  
Rectangular  
Carpet/Black  
Yes  
Rectangular  
Carpet/Black  
Yes  
Finish Colour  
Stand Adaptor  
Protect Corner  
Handle  
Black metal  
Black metal  
Black metal  
Black metal  
Black metal  
Black metal  
Black metal  
7. CAUTION: These professional loudspeaker systems are capa-  
ble of generating very high sound pressure levels. Use care with  
placement and operation to avoid exposure to excessive levels  
that can cause permanent hearing damage.  
2
2
2
2
2
2
2
1
1
1
1
1
1
1
INPUT CONNECTOR  
2 x  
4”phone  
No  
2 x  
4” phone  
No  
2 x  
4” phone  
No  
2 x  
4” phone  
No  
2 x  
4” phone  
No  
2 x  
4” phone  
2 x  
4” phone  
1
1
HIGH PASS OUT  
4” phone  
4” phone  
DIMENSIONS (H x W x D)  
494 x 317 x 288 554 x 428 x 355 415 x 248 x 554 638 x 463 x 390 1014 x 463 x 390 587 x 548 x 429 748 x 548 x 450  
10.28kg 15.58kg 14.9kg 19.26kg 31.0kg 31.52kg 38.56kg  
8. SERVICING - The user should not attempt to service this prod-  
WEIGHT  
uct.  
Wharfedale Pro SVP Series of Professional Sound Reinforcement Loudspeakers  
SVP-15B AND SVP- 18B SUB-WOOFER:  
Reliable, Durable construction  
Trapezoid shape for arraying cabinets  
Integral tripod stand adaptor  
Application  
Proprietary designed, high efficiency, high power  
For extended bass response in a multi way (2 or more) equalized  
system designed for high quality reproduction of voice, music and  
musical instruments, for mobile or fixed installations.  
Wharfedale Professional drive units.  
Low resonance enclosure design  
Protective grills  
Full range and complimentary Sub Bass systems  
Description  
Integral High Frequency Driver Overload protection  
Exceptional sound quality, with broad bandwidth  
These cabinets are all covered in tough impact resist carpet. They  
are designed for portability and are fitted with heavy duty handles  
and a ‘kick -proof’ steel protective grille. The SVP-18B and the SVP-  
15B have two 1/4” phone type jack sockets and are paralleled at the  
rear of each cabinet. (See diagram ).  
“PRO-TECH”™  
and dynamic range  
Sophisticated crossover design enables smooth  
power and frequency response control through  
crossover region  
High Power Handling  
Metal corner protectors  
A very special feature of these products is that they have built-in  
crossovers with high-pass outputs. This means that you may use  
one channel of your power amplifier to power both a subwoofer and  
a full-range speaker, while maintaining a reason-able load on your  
amplifier. The amplifier only sees the subwoofer/crossover load  
which is 8 ohms for SVP series subwoofers. Without the built-in  
crossover, the combined impedance of full-range and subwoofer  
speakers in parallel would be much lower. Also, the high-pass  
crossover output removes the very low bass frequencies from the  
signal going to the full-range speaker. This prevents distortion (and  
possible damage) from excessive low-frequency energy getting into  
the full-range speaker.  
Unpacking  
All Wharfedale Pro products are fully  
checked before leaving the factory. After  
unpacking please inspect cabinets for any  
Wharfedale Pro Limited Warranty*  
Wharfedale Pro SVP Series loudspeaker systems are warranted to be  
clear of manufacturing or materials defects for a period of one year from  
the original date of purchase. In the event of malfunction, contact your  
authorised Wharfedale Professional dealer or distributor for information.  
physical damage. Please retain the shipping  
carton if possible and internal packing material in case the unit  
needs to be returned. Please check as soon as possible the unit is  
functioning. In the event of any damage please contact your dealer  
immediately so that a written claim for damages can be made.  
*Be aware that warranty details may differ from country to country. Contact your dealer or  
distributor for information.  
These terms do not infringe your statutory rights.  
SVP 10, SVP-12,SVP-15,SVP215  
Operating:  
The Wharfedale Pro SVP-10, SVP-12, SVP15 and SVP-215 fea-  
Note: Each speaker connected in parallel increases the load on  
the amplifier and can add up to a total load that may exceed the  
amplifier’s capabilities, leading to possible damage.Two 8loud-  
ture two 1/4”phone jack socket connectors and are paralleled. speakers in parallel make a 4total load. Four 8parallel con-  
This means that these cabinets can be linked together with  
other cabinets of the same impedance and design or with a  
sub-bass unit.  
CAUTION: If you are unsure of any of thes procedures, check  
with your dealer or an experienced sound engineer.  
(1) Ensure you do not overload the amplifier you are using by  
linking too many units together and lowering the resistance  
(impedance) below the safe operating level of the amplifier.  
nected loudspeakers make a total load of 2, which is too low for  
many amplifiers.  
(2) Make sure that the speaker cable used is securely  
attached to the amplifier and the cabinet.  
(3) Check all cables from the source unit (mixer or other  
source) to the amplifier. Check all power cables to all the  
electronic systems powering the loudspeakers and ensure  
that they meet with required safety standards.  
911.400  
Wharfedale International Limited, IAG House, Sovereign Court, Ermine Business Park, Huntingdon, Cambs, PE29 6XU England  
WHARFEDALE website : www.wharfedalepro.com  
IAG Professional reserve the right to alter or improve specifications without notice.All rights reserved © 2004 Wharfedale Pro. A member of the International Audio Group  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Weslo Treadmill WETL147070 User Manual
Westinghouse Indoor Furnishings W 128 User Manual
Whirlpool Air Conditioner ACE244PT0 User Manual
Whirlpool Dehumidifier AD25BSS User Manual
Whirlpool Trash Compactor GARAGE COMPACTOR User Manual
Williams Sound Switch MOD 232 User Manual
Xerox Printer WC PE120 Series User Manual
Yamaha Music Mixer LSP User Manual
Zebra Technologies All in One Printer ZD500 User Manual
Zenoah Brush Cutter TR2300 User Manual