Item #
70284, 70287, 85718
Mini-Pendant Kit
Installation and Safety Instructions
Warning: Be sure the electricity to the wires you are working on is shut off; either the fuse is removed
or the circuit breaker is shut off.
General
You don't need special tools to install this fixture. Be sure to follow the steps in the order given. Under no
circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on
a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to
how to proceed, consult a qualified electrician.
A
I
B
C
F
D
G
H
InStallatIon
Important: Do not attach fixture directly to outlet box.
Step 1: Thread mounting screw (A) into the matching hole of mounting bar (B).
Step 2: Secure the mounting bar (B) to outlet box with outlet box screws (C) (not provided).
GroUnDInG anD WIrInG InStrUCtIonS
Step 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the
bare grounding wire (F) from the fixture canopy around the green grounding screw (G) on the cross bar
and tighten the grounding screw. Then connect the greenish grounding wire (H) from hanging cord to
the house supply grounding wire (I) by using a wire connector. Never connect grounding wire to black
or white power supply wires.
E
Step 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into
and connect the wires according to the directions below.
Group a: Connect to black house wire: transparent, brownish grey or brown with tracer (with black
label)
Group B: Connect to white house wire: transparent or without tracer (with white label)
Group C: Connect to house grounding wire: transparent or greenish (with green label)
*Note: When parallel wire (SVT) is used, the tracer wire is connected to group A and the wire without
a tracer is connected to group B (seen best when viewed from wire end).
Step 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box.
Do NOT twist wires together before using wire connectors.
Step 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
Step 5: Try to gently pull the connectors off the wires. If you can pull the connector off, carefully repeat
steps 3 and 4 above, and check again for a firm connection.
Step 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner.
Make sure no bare wires can be seen outside wire connectors.
FInal aSSeMBly
Step 1: After wires are connected, tuck them carefully inside outlet box. Raise canopy (D) allowing the
mounting screw (A) to protrude through the hole in the canopy (D), and secure with ball nut (E).
Step 2: Install the glass onto the socket (J) and secure the retaining ring (K).
Step 3: Install lamp. (Please do not exceed the maximum capacity recommended on the socket).
J
K
CleanInG
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
Westinghouse Lighting Corporation, Philadelphia, PA 19154-1029, U.S.A.
Westinghou g Corporation, a Westinghouse Electric Corporation licensee
and “Westinghouse” are registered trademarks of Westinghouse Electric Corporation
y “Westinghouse”estan marca registrada por Westinghouse Electric Corporation
et “Westinghouse” sont des marques déposéesde Westinghouse Electric Corporation
Made in China / Hecho en China / Fabriqué en Chine
© 2013 WESTINGHOUSE LIGHTING CORP.
Download from Www.Somanuals.com. All Manuals Search And Download.
|