¨
USER'S MANUAL
Model No. WLTL48590
Serial No.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assistance
from our factory.
TO AVOID UNNECESSARY DE-
LAYS, PLEASE CALL DIRECT TO
OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our Customer Hot Line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. Inspect and tighten all parts of the treadmill
regularly.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
21. Never drop or insert any object into any
opening.
16. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 4 for the loca-
tion of the on/off switch.)
22.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
17. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO MOVE
THE TREADMILL on page 10.) You must be
able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill.
23. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
18. Do not change the incline of the treadmill by
placing objects under the treadmill.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown has been placed on your treadmill. If the decal
is missing, or if it is not legible, please call our Customer Service
Department, toll-free, to order a free replacement decal (see
ORDERING REPLACEMENT PARTS on the back cover of this
manual). Apply the decal in the location shown.
Note: The decal is shown at 38% of actual size.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the WESLO¨ CADENCE SL25
treadmill. The CADENCE SL25 treadmill combines ad-
vanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
youÕre not exercising, the unique CADENCE SL25 can
be folded up, requiring less than half the floor space of
other treadmills.
please call our Customer Service Department toll-free
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is WLTL48590. The serial
number can be found on a decal attached to the tread-
mill (see the front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Book Holder
Water Bottle
Holder (Bottle
not included)
Accessory Tray
Console
Handrail
Handrail
Key/Clip
Storage Latch
LEFT SIDE
RIGHT SIDE
On/Off Switch
Walking Belt
Circuit
Breaker
Front
Wheel
Foot Rails
Power Cord
Rear Roller
Adjustment Bolts
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
, adjustable wrench
, and scissors
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
treadmill to the upright position.
1
While the other person tips the treadmill to one side and
holds it, insert an Extension Leg (59) into one side of
the Base (32). Make sure that the Extension Leg is
turned so the bracket is on the side shown. Using the
Allen Wrench (102), tighten an Extension Leg Screw
(57) into the Extension Leg and the Base. Attach the
other Extension Leg in the same manner.
Bracket
102
57
59
32
2. Refer to HOW TO LOWER THE TREADMILL FOR
USE on page 11. Follow the instructions in step 2 to
lower the treadmill.
2
46
60
35
Cut the plastic ties holding the cage nuts in the upper
end of each Handrail (60, 62).
30
62
30
Position the Left Handrail (60) on the left Upright (32) as
shown. The bracket on the Extension Leg (59) should
be inside of the lower end of the Left Handrail (see the
inset drawing). Thread two Handrail Bolts (30) with
Handrail Washers (40) into the left Upright and the Left
Handrail. Do not tighten the Handrail Bolts yet.
40
40
30
30
32
While another person holds the Console Base (46),
insert all excess Wire Harness (35) through the Right
Handrail (62) and into the right Upright. Next, attach the
Right Handrail in the same way that you attached the
Left Handrail. Be careful to avoid damaging the Wire
Harness (35).
59
59
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Set the Console Base (46) on the Handrails (60, 62).
Route the Wire Harness (35) under the Console Base
as shown and then press the Wire Harness up into the
Console Base. Insert any slack into the Right Handrail
(62).
3
46
62
Attach the Console Base (46) to the Handrails (60, 62)
with the four Long Console Screws (24).
35
24
60
24
4. Attach the Storage Latch (34) and the two Latch
Spacers (33) to the left Upright (32) with two Screws
(28). Be careful not to overtighten the Screws.
4
Note: If it is difficult to fold or lower the treadmill, re-
move one or both of the Latch Spacers (33).
32
Fold the treadmill to the storage position (see HOW TO
FOLD THE TREADMILL FOR STORAGE on page 10).
33
28
34
5. Attach the lower end of the Right Handrail (62) to the
right Extension Leg (59) with a Screw (28).
5
Attach the lower end of the Left Handrail (60) in the
same way.
60
Tighten all parts used in this step and in step 2.
59
28
62
28
59
6. The console requires three "AA" batteries (not included).
Alkaline batteries are recommended. To install batteries,
first touch the Handrail (6) to discharge any static.
Next, open the Battery Cover (23). Press the batteries
into the battery compartment, with the negative (Ð) ends
of the batteries touching the springs. Close the battery
cover, push up on the tab, and then push the tab for-
ward as shown in the inset drawing. Be sure that the tab
locks into place.
23
6
Battery
Cover Tab
Batteries
7. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet,
place a mat under the treadmill.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an ap-
propriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. They will deteriorate the walking belt and
cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole recep-
tacle as shown in drawing 2 if a properly grounded out-
let is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet in-
stalled by a qualified electrician.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can re-
sult from weather conditions or from other appliances
being turned on or off.
To decrease the pos-
sibility of your tread-
1
Grounded Outlet Box
mill being damaged,
always use a surge
protector (not in-
cluded) with your
treadmill.
Treadmill Power Cord
Grounding Pin
Grounding Plug
Grounding Plug
Grounding Pin
Surge protectors are
sold at most hardware
stores and department
stores. Use only a UL-
listed surge protector,
rated at 15 amps, with a
14-gauge cord of five
feet or less in length.
Grounded Outlet
2
Grounded Outlet Box
Adapter
Grounding Pin
Grounding Plug
This product must be
grounded. If it should
malfunction or break
Surge Protector
down, grounding pro-
vides a path of least re-
sistance for electric cur-
rent to reduce the risk of
Lug
Metal Screw
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
Monitor Displays
LED Track
Incline Control
Note: If there is a thin sheet of clear
plastic on the console, remove it.
Speed Control Clip
Key
CAUTION:
Before operating the con-
sole, read the following precautions.
¥ Adjust the speed in small increments.
¥ The training zones marked around the speed
control are general guidelines only. See pages
14 and 15 for more information.
¥ Do not stand on the walking belt when turning
on the power.
¥ Always wear the clip (see the drawing above)
while operating the treadmill. When the key is
removed from the console, the walking belt will
stop.
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids on
the console. Use only a sealed water bottle.
-
STEP BY STEP CONSOLE OPERATION
-
Follow the steps below and on page 9 to operate the
console.
If there is a thin sheet of clear plastic on the face of the
console, remove it. Next, make sure that the power cord
is properly plugged in (see
Insert the key fully into the power switch.
1
HOW TO PLUG IN THE
POWER CORD on page
When the key is in-
serted, the first indica-
tor in the LED track
will light. The four dis-
plays will not turn on
until the ON/RESET
On
Position
7). Be sure that the on/off
switch near the power cord
is in the on position.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothing.
button is pressed or
the walking belt is started. Note: If you just installed
batteries, the displays will already be on.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset the speed control.
The TIME displayÑ
This display shows
the total time that you
have walked or run on
the treadmill.
2
Slide the speed control
down to the RESET
position. Note: Each
time the walking belt is
stopped, the speed
control must be moved
to the RESET position
before the walking belt
can be restarted.
The DISTANCE dis-
playÑThis display
shows the total dis-
tance that you have
walked or run, in miles.
The SPEED displayÑ
This display shows the
speed of the walking
belt, in miles per hour.
Start the walking belt.
3
4
After you have moved the speed control to the
RESET position, slide it slowly upward until the
walking belt begins to move at slow speed.
Carefully step onto the walking belt and begin ex-
ercising. Change the speed of the walking belt as
desired by sliding the speed control.
The CALORIES/
FAT CALORIES
Arrow
displayÑThis display
shows the approximate
numbers of calories
and fat calories you
have burned. (See FAT
BURNING on page 14.) Every seven seconds, the
display will change from one number to the other.
Arrows in the display will indicate which number is
currently shown.
To stop the walking belt, step onto the foot rails
and slide the speed control to the RESET position.
Change the incline of the treadmill, if desired.
To increase or de-
crease the incline, hold
down the top or bottom
of the incline control.
Note: The displays can be reset by pressing the
ON/RESET button.
Important: Change
the incline of the
treadmill only with
the incline control.
When you are finished exercising, stop the
walking belt and remove the key.
6
Do not place objects
under the treadmill to change the incline.
Step onto the foot
rails, stop the walking
belt, and remove the
key from the console.
Store the key in a se-
cure place. After the
Follow your progress with the LED track and
the four monitor displays.
5
The LED
TrackÑThe
key is removed, the
displays will remain on for about five minutes.
LED track in the
center of the
console repre-
sent a distance
Note: Any time that the walking belt is stopped
and no console buttons are pressed for five
minutes, the displays will automatically turn off.
of 1/4 mile. As
you exercise,
the indicators
around the track will light one at a time until you
have completed 1/4 mile. The first indicator above
the word START will then light and another lap will
begin.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. Caution: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold
the treadmill firmly. Using your left thumb, press the
storage latch to the left as you raise the treadmill to
the storage position. Release the storage latch,
making sure that it closes fully over the catch.
Closed
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85¡ Fahrenheit.
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the stor-
age latch is closed fully over the catch.
Book Holder
1. Hold the handrails as shown and place one foot against a
wheel. Do not hold or push on the book holder or the
book holder may be damaged.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Base
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
Front Wheels
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left thumb, press the storage latch and
hold it. Pivot the treadmill until the frame is past the
storage latch.
Opened
Storage
Latch
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Caution: To decrease the possibil-
ity of injury, bend your legs and keep your back
straight.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is
plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page
7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or
less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole. (See step 1 on page 8.)
c. Check the circuit breaker located on the treadmill
c
near the power cord. If the switch protrudes as
Tripped
Reset
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d
d. Check the on/off switch located at the front of the
treadmill near the power cord. The switch must be
in the on position.
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. (See step 1 on page 8.)
d. Make sure that the on/off switch is in the on position. (See 1. d. above.)
e. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Next, remove the screws from the
hood and carefully remove the hood. Locate the Reed
1/8Ó
Switch (97) and the Magnet (9) on the left side of the
10
98
Pulley (10). Turn the Pulley until the Magnet is aligned
with the Reed Switch. Check the gap between the
Magnet and the Reed SwitchÑit should be about
1/8Ó. If necessary, loosen the Screw (98) and move
the Reed Switch slightly. Retighten the Screw.
Reattach the hood and run the treadmill for a few min-
utes to check for a correct speed reading.
97
9
Top
View
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in
length.
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be
b
2ÓÐ3Ó
permanently damaged. Remove the key and UN-
PLUG THE POWER CORD. Using the allen wrench,
turn both rear roller adjustment bolts counterclock-
wise, 1/4 of a turn. When the walking belt is properly
tightened, you should be able to lift each side of the
walking belt 2 to 3 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key and run the treadmill for a
few minutes. Repeat until the walking belt is properly
tightened.
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-
free.
PROBLEM: The walking belt is off-center when walked on
SOLUTION: a. If the walking belt has shifted to the left, first remove
the key and UNPLUG THE POWER CORD. Using
a
the allen wrench, turn the left rear roller adjustment
bolt clockwise, and the right bolt counterclockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
b. If the walking belt has shifted to the right, first remove
the key and UNPLUG THE POWER CORD. Using
b
the allen wrench, turn the left rear roller adjustment
bolt counterclockwise, and the right bolt clockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
PROBLEM: The walking belt slips when walked on
SOLUTION: a. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
a
the allen wrench, turn both rear roller adjustment
bolts clockwise, 1/4 of a turn. When the walking belt
is correctly tightened, you should be able to lift each
side of the walking belt 2 to 3 inches off the walking
platform. Be careful to keep the walking belt centered.
Plug in the power cord, insert the key and carefully
walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
training zone. It may also be helpful to set the speed
control on the console to FAT BURN to help you main-
tain the proper intensity level. (See page 8.)
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for in-
dividuals over the age of 35 or individuals
with pre-existing health problems.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone. It may also be helpful to set the speed control on
the console to AEROBIC to help you maintain the
proper intensity level. (See page 8.)
The following guidelines will help you to plan your ex-
ercise program. RememberÑthese are general guide-
lines only. For more detailed exercise information, ob-
tain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the de-
sired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exer-
cise.
High Performance Athletic Conditioning
If your goal is high performance athletic conditioning,
set the speed control on the console to PERFOR-
MANCE to help you maintain the proper intensity level.
(See page 8.) Note: During the first few weeks of your
exercise program, keep your heart rate near the low
end of your training zone.
HOW TO MEASURE YOUR HEART RATE
To measure your
heart rate, stop ex-
ercising and place
two fingers on your
wrist as shown.
Take a six-second
heartbeat count,
and multiply the re-
sult by ten to find
To find the proper heart rate for you, first find your age
on the left side of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers to
the right of your age. The three numbers are your
Òtraining zone.Ó The lower two numbers are recom-
mended heart rates for fat burning; the higher number
is the recommended heart rate for aerobic exercise.
your heart rate. (A six-second count is used because
your heart rate drops quickly when you stop exercis-
ing.) If your heart rate is too high or too low, adjust the
speed or incline of the treadmill accordingly.
WORKOUT GUIDELINES
A well-rounded workout includes the following three
important parts:
Fat Burning
A Warm-up
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn fat,
adjust the speed and incline of the treadmill until your
heart rate is near one of the lower two numbers in your
Start each workout with 5 to 8 minutes of stretching
and light exercise (see SUGGESTED STRETCHES on
page 15). A proper warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Training Zone Exercise
to cool down. This will increase the flexibility of your
muscles and will help to prevent post-exercise problems.
After warming up, increase the intensity of your exer-
cise until your heart rate is in your training zone for 20
to 60 minutes. (During the first few weeks of your exer-
cise program, do not keep your heart rate in your train-
ing zone for longer than 20 minutes.) Breathe regularly
and deeply as you exerciseÑdo not hold your breath.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired.
A Cool-down
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
Finish each workout with 5 to 8 minutes of stretching
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the
right. Move slowly as you stretchÑnever bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees, and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back, and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your
back foot flat on the floor. Bend your front leg, lean forward and
move your hips toward the wall. Hold for 15 counts, then relax.
Repeat 3 times for each leg. To cause further stretching of the
achilles tendons, bend your back leg as well. Stretches:
Calves, achilles tendons, and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close to
your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for both legs. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold
for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. WLTL48590
Key No. Qty.
R0899A
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
2
6
2
1
1
1
1
2
2
1
11
1
4
2
6
1
1
1
2
4
1
1
1
10
2
4
2
1
2
1
1
1
1
4
2
9
2
1
3
1
1
1
1
1
1
1
1
1
2
4
4
2
2
4
Frame
Catch Screw
Latch Catch
Rear Roller
Roller Guard
Platform Screw
Foot Rail
Walking Platform
Magnet
Front Roller/Pulley
Walking Belt
Rear Isolator
Rear Isolator Bolt
Latch Warning Decal
Belly Pan Screw
Belly Pan
59
60
61
62
63
64*
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
#
2
1
2
1
1
1
2
1
1
1
3
1
1
1
1
1
5
2
1
16
2
5
1
1
1
1
1
5
2
1
1
6
1
1
1
1
1
1
1
10
1
1
2
1
1
6
1
4
5
2
1
1
1
1
1
Extension Leg
Left Handrail
Extension Leg Endcap
Right Handrail
Rear Endcap
Console Assembly
Front Wheel
Motor/Pulley/Flywheel/Fan
Motor Pivot Bolt
Motor Tension Nut
Motor Star Washer
Motor Tension Washer
Motor Tension Bolt
Motor Belt
Pulley/Flywheel/Fan
Motor
8Ó Wire Tie
Belt Guide
Endcap Foot (left)
Small Screw
Rear Roller Adj. Bolt
Hood Anchor
Circuit Breaker
Power Cord
Power Cord Grommet
On/off Switch
Outlet Bracket
Hood Bracket
Spacer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Isolator
Frame Pivot Bolt
Hood Screw/Bracket Screw
Hood
Key/Clip
Book Rack
Battery Cover
Long Console Screw
Incline Control
Speed Control
Speed Potentiometer
Screw
Rear Platform Screw
Handrail Bolt
Frame Pivot Washer
Upright/Base
Latch Spacer
Latch
Wire Harness
Grommet
4.5Ó Spacer
Electronics Bracket
Front Roller Nut
Controller
Front Roller Adj. Bolt
Incline Leg
Choke Plate
Choke
Reed Switch Clip
Reed Switch
Belly Pan Fastener/Clip Screw
Front Belly Pan
Ground Wire
4Ó Cable Tie
Allen Wrench
Endcap Plug
Endcap Fastener
Endcap Foot (Right)
Endcap Bolt
Incline Motor Nut
Cage Nut
Incline Leg Pivot Bolt
Adj. Washer/Handrail Washer
Incline Leg Pivot Nut
Incline Cover Shield
Belly Pan Screw/Reed Switch Screw
Incline Motor Spacer
Incline Motor
Console Base
Incline Stop Bracket
Incline Bolt
Shock
Incline Cover
Cotter Pin
Clevis Pin
Wheel Bolt
Base Pad Screw
Base Pad
Rear Isolator Nut
Extension Leg Screw
Isolator Nut
Releasable Tie
Wire Clip
8Ó Black Wire, Male/Female
4Ó Black Wire, 2 Female
8Ó White Wire, Pig Tail
8Ó Blue Wire, Pig Tail
UserÕs Manual
#
#
#
#
* Includes all parts shown in the box
# These parts are not illustrated
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWINGÑModel No. WLTL48590
R0899A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
¥ The MODEL NUMBER OF THE PRODUCT (WLTL48590).
¥ The NAME OF THE PRODUCT (WESLO¨ CADENCE SL25 treadmill).
¥ The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual).
¥ The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING and PART LIST
attached to the center of this manual).
If possible, place the treadmill near your telephone for easy reference when calling.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service
centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of pur-
chase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal
usage or repairs not provided by an ICON authorized service center, to products used for commercial or
rental purposes, or to products used as store display models. No other warranty beyond that specifically
set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 157710 J02106-C R0899A
Printed in USA © 1999 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|