Model No. WLTL27081
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal
¨
QUESTIONS?
USER'S MANUAL
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfac-
tion through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
20. When storing the treadmill, make sure that
the storage latch is fully closed.
21. Inspect and tighten all parts of the treadmill
every three months.
16. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
22. Never drop or insert any object into any
opening.
23.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
17. Never leave the treadmill unattended while it
is running. Always remove the key when the
treadmill is not in use.
18. Do not change the incline of the treadmill by
placing objects under the treadmill.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO MOVE
THE TREADMILL on page 10.) You must be
able to safely lift 45 pounds (20 kg) in order
to raise, lower, or move the treadmill.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or prop-
erty damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has
been placed on your treadmill. If the
decal is missing, or if it is not legible,
please call our Customer Service
Department, toll-free, to order a free
replacement decal (see ORDERING
REPLACEMENT PARTS on the back
cover of this manual). Apply the decal
in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the WESLO¨ CADENCE 1010
treadmill. The CADENCE 1010 treadmill combines
advanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
youÕre not exercising, the unique CADENCE 1010 can
be folded up, requiring less than half the floor space of
other treadmills.
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is WLTL27081. The serial
number can be found on a decal attached to the tread-
mill (see the front cover of this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Speed Control
Console
Water Bottle Holder
(Bottle not included)
Accessory Tray
Book Rack
Key/Clip
Handrails
Storage Latch
Walking Belt
FRONT
Foot Rails
Circuit Breaker
Cushioned Deck
Incline Leg
Power Cord
BACK
Rear Roller
Adjustment Bolts
RIGHT SIDE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
scissors
, adjustable wrench
, and
.
1. Note that the Right Handrail (32) and the Console
Base (not shown) are connected to the treadmill by
the Wire Harness (53). During assembly steps 1
through 5, be careful to avoid pulling on or dam-
aging the Wire Harness.
1
39
81
38
44
With the help of a second person, carefully lay the
treadmill onto one side. Insert one of the Base Legs
(44) into the Upright (38) as shown. Make sure that
the Base Leg Pad (33) is in the indicated position.
Using the included Allen Wrench (81), attach the
Base Leg with a Base Leg Screw (39).
33
53
Attach the other Base Leg (44) as described above.
With the help of a second person, carefully raise the
treadmill to the upright position so that both Base
Legs (44) are resting flat on the floor.
44
33
39
32
2. Carefully lower the treadmill. Remove the two indi-
cated Latch Screws (14) and the shipping bracket
from the left Upright (38). Save the Latch Screws
for use in assembly step 3; discard the shipping
bracket.
2
Shipping
Bracket
38
14
3. Remove the two remaining Latch Screws (14) from
the left Upright (38).
3
38
17
Without removing the tape from the Latch Bracket
(16) and the Latch Spacer (13), attach both parts to
the left Upright (38) with the four Latch Screws (14).
Make sure that the Latch Screws are tight, but
do not overtighten them; if the Latch Screws are
overtightened, the Storage Latch (17) will not
slide smoothly. Remove any visible tape from the
Latch Bracket and the Latch Spacer.
13
14
13
16
15
Note: The inset drawing shows how the Latch
Bracket (16), Latch Springs (15), Storage Latch (17),
and Latch Spacer (13) fit together.
17
16
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the shipping tie from the Left Handrail (4)
and Handrail Spacer (3). Attach the Left Handrail and
Handrail Spacer to the left Upright (38) with two
Handrail Bolts (1) and Handrail Washers (70) as
shown. Make sure that the ramps on the Handrail
Spacer is on the inside as shown. Do not tighten the
Handrail Bolts until step 5 is completed.
4
1
32
53
38
4
38
3
Ramps
70
3
Remove the shipping tie from the Right Handrail (32)
and Handrail Spacer (3). Hold the Handrail Spacer
against the right Upright (38) and feed the excess
Wire Harness (53) into the right Upright. Attach the
Right Handrail and Handrail Spacer to the right
Upright with two Handrail Bolts (1) and Handrail
Washers (70). Do not tighten the Handrail Bolts
until step 5 is completed.
70
1
5
67
53
5. Set the Console Base (67) on the Handrails (4, 32).
Route the Wire Harness (53) as shown. Attach the
Wire Harness to the Right Handrail (32) with the
Harness Clip (103) and a Handrail Screw (5); do not
fully tighten the Handrail Screw yet. Then loosely
thread the other three Handrail Screws (5) into the
Console Base. After all four Screws are threaded, firm-
ly tighten the Screws. Be careful not to overtighten
the Screws. Insert the excess Wire Harness (53) into
the Right Handrail.
103
5
4
32
5
6
Tighten the four Handrail Bolts (1) used in step 4.
38
6. Remove the backing from the Adhesive Clip (80).
Press the Adhesive Clip onto the right Upright (38) in
the indicated location. Press the Allen Wrench (81)
into the Adhesive Clip.
81
80
7. The Console (11) requires three "AA" batteries (not
included); alkaline batteries are recommended.
7
12
11
Open the Battery Cover (12) as shown. Press three
batteries into the battery compartment, with the nega-
tive (Ð) ends of the batteries touching the springs.
Close the battery cover, push up on the battery cover
tab, and then push the tab forward as shown in the
inset drawing. Be sure that the tab locks into place.
Battery Cover Tab
Batteries
8. Make sure that all parts are tight before you use
the treadmill. (Note: The ratchet screws shown at the
far right are factory set and should not be adjusted.)
To protect the floor or carpet from damage, place a
mat under the treadmill.
Ratchet
Screws
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
risk of electric shock. This product is equipped with a
cord having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. They will deteriorate the walking belt and
cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole recep-
tacle as shown in drawing 2 if a properly grounded
outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet
box covers are not grounded. Contact a qualified
electrician to determine if the outlet box cover is
grounded before using an adapter.
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on
or off. To decrease the
possibility of your
1
Grounded Outlet Box
treadmill being dam-
aged, always use a
surge protector (not
included) with your
treadmill.
Treadmill Power Cord
Grounding Pin
Grounding Plug
Grounding Plug
Grounding Pin
Surge protectors are
sold at most hardware
stores and department
stores. Use only a UL-
listed surge protector,
rated at 15 amps, with
a 14-gauge cord of five
feet or less in length.
Grounded Outlet
2
Grounded Outlet Box
Adapter
Grounding Pin
Grounding Plug
This product must be
grounded. If it should
malfunction or break
down, grounding pro-
vides a path of least
resistance for electric
current to reduce the
Surge Protector
Lug
Metal Screw
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
Speed Control
PulseSensor
Clip
Key
Follow the steps below to operate the console.
CAUTION: Before operating the
console, read the following precautions.
Insert the key fully into the power switch.
1
Note: Inserting the key
will not turn on the dis-
plays. The displays will
turn on when the
DISPLAY ON/RESET
button is pressed or
when the walking belt
is started. If you just
installed batteries, the displays will already be on.
¥ Do not stand on the walking belt when turn-
ing on the power.
¥ Always wear the clip (see the drawing
above) while operating the treadmill. When
the key is removed from the console, the
walking belt will stop.
¥ Adjust the speed in small increments.
¥ The training zones marked beside the
speed control are general guidelines only.
See page 14 or more information.
Reset the console and start the walking belt.
2
Slide the speed control to the
RESET position. Note: Each
time the walking belt is
stopped, the speed control
must be moved to the RESET
position before the walking
belt can be restarted.
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and use only a sealable
water bottle.
STEP BY STEP CONSOLE OPERATION
Next, slowly slide the speed
control until the walking belt
begins to move at slow speed.
Carefully step onto the walking
belt and begin exercising.
Change the speed of the walk-
ing belt as desired by moving
the speed control.
Before operating the console, make sure that the
power cord is properly plugged in. (See HOW TO
PLUG IN THE POWER CORD on page 7.) In addition,
make sure that batteries are installed in the console.
(See step 7 on page 6.) If there is a thin sheet of clear
plastic on the console, remove it.
Step onto the foot rails of the treadmill. Next, find the
clip attached to the key (see the drawing above). Slide
the clip onto your waistband.
To stop the walking belt, step onto the foot rails
and move the speed control to the RESET position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
After a few seconds, three dashes will appear in the
display and your pulse will be shown. Hold your
thumb on the sensor for another 15 seconds for the
most accurate reading.
Follow your progress with the three displays.
3
TIME/DISTANCE
displayÑThis display
shows the elapsed
time and the distance
that you have walked
or run, in miles. The
display will change between TIME and DISTANCE
approximately every seven seconds.
If the displayed pulse appears to be too high or too
low, or if your pulse is not displayed, lift your thumb
off the sensor and allow the display to reset. Press
down again on the sensor as described above.
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of
pressure to the pulse sensor. Try the sensor several
times until you become familiar with it. Remember to
stand still while measuring your pulse.
SPEED displayÑThis
display shows the
speed of the walking
belt, in miles per hour.
Turn off the power.
5
CALORIES/FAT CAL-
ORIES/PULSE dis-
playÑThis display
shows the approxi-
mate numbers of
To turn off the power, simply wait for about six
minutes. If the walking belt is stationary and the
console button is not pressed for six minutes, the
power will turn off automatically.
Mode Arrows
calories and fat calo-
ries you have burned.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
(See FAT BURNING on page 14.) Every seven sec-
onds, the display will change from one number to
the other. Arrows in the display will indicate which
number is currently shown. This display also shows
your pulse when the pulse sensor is used (see step
4).
The incline of the treadmill can be changed by raising
or lowering the back end. Before changing the
incline, remove the key and unplug the power cord.
Hold the rear
roller endcap
with both
hands. When
the back end of
the treadmill is
in the lowest
The displays can be
reset, if desired, by
pressing the DISPLAY
ON/RESET button.
position, the
Incline Leg
incline is about
10%. Raise the
back end until
Measure your pulse, if desired.
4
To measure
your pulse,
stand on the
foot rails and
Pulse
Sensor
it clicks into position. (Note: It may be necessary to
shake the treadmill lightly so that it clicks into position.)
The incline will then be about 5%. Raise the back end
again until it clicks into position. The incline will then be
about 3%. To lower the back end, first raise it past the
highest position and then lower it. CAUTION: Before
exercising, push on the back of the treadmill to
make sure that the incline legs are locked in posi-
tion. Do not place objects under the treadmill to
change the incline; change the incline only as
described above.
place your
thumb on the
pulse sensor as
shown. The
pulse sensor is pressure activatedÑfully press it
down. Do not press too hard, or the circulation
in your thumb will be restricted, and your pulse
will not be detected.
Next, raise your
thumb slightly until
the heart-shaped indi-
cator in the PULSE
display flashes
Pulse Indicator
steadily. Hold your
thumb at this level.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
Caution: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown at the right,
and hold the treadmill firmly. Raise the treadmill until the
storage latch locks over the frame guide. Make sure that
the storage latch closes fully over the frame guide.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85¡ Fahrenheit.
Closed
Storage
Latch
Frame
Guide
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
storage latch is locked fully over the frame guide.
1. Hold the upper ends of the handrails. Place one foot near
one of the front wheels as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired loca-
tion. Never move the treadmill without tipping it back.
To reduce the risk of injury, use extreme caution
while moving the treadmill. Do not attempt to move
the treadmill over an uneven surface.
Base Leg
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
Front Wheels
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left thumb, slide open the storage
latch and hold it open. Pivot the treadmill until the frame
is past the storage latch.
Opened
Storage
Latch
Frame
Guide
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of
injury, bend your legs and keep your back straight.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is
plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page
7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or
less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole. See step 1 on page 8.
c. Check the circuit breaker located on the treadmill
c
frame near the power cord. If the switch pro-
trudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 8.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 8 on
page 6. Most problems are the result of drained batteries.
b. Remove the key and UNPLUG THE POWER CORD.
Remove the screws from the hood. Locate the Reed
1/8Ó
89
Switch (89) and the Magnet (88) on the left side of
the Pulley (90). Turn the Pulley until the Magnet is
aligned with the Reed Switch. Make sure that the
gap between the Magnet and the Reed Switch is
about 1/8Ó. If necessary, loosen the Screw (28) and
move the Reed Switch slightly. Retighten the Screw.
Re-attach the hood, and run the treadmill for a few
minutes to check for a correct speed reading.
90
88
28
Top
View
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt clockwise, and the right bolt counterclock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centered.
a
b. If the walking belt has shifted to the right, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt counterclockwise, and the right bolt clock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centered.
b
c. If the walking belt slips when walked on, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller adjust-
ment bolts clockwise, 1/4 of a turn. When the walking
belt is correctly tightened, you should be able to lift
each side of the walking belt 2 to 3 inches off the
walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key and
run the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
a
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less
in length.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be
permanently damaged. Remove the key and
UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment bolts coun-
terclockwise, 1/4 of a turn. When the walking belt is
properly tightened, you should be able to lift each
side of the walking belt 2 to 3 inches off the walking
platform. Be careful to keep the walking belt cen-
tered. Plug in the power cord, insert the key and run
the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
2ÓÐ3Ó
Rear Roller
Adjustment Bolts
c. If the walking belt still slows when walked on, please call our toll-free Customer Service
Department.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the middle of your training zone. (See
pages 8 and 9.)
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
High Performance Athletic Conditioning
If your goal is high performance athletic conditioning, set
the speed control on the console to PERFORMANCE to
help you maintain the proper intensity level. Note: During
the first few weeks of your exercise program, keep your
heart rate near the low end of your training zone.
The following guidelines will help you to plan your exer-
cise program. RememberÑthese are general guide-
lines only. For more detailed exercise information,
obtain a reputable book or consult your physician.
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed of the treadmill as
needed.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The prop-
er intensity level can be found by using your heart rate
as a guide. To find the proper heart rate for you, first
find your age at the top of the chart below (ages are
rounded off to the nearest ten years). Next, find the two
numbers below your age. The two numbers are your
Òtraining zone.Ó
Each workout should include the following three parts:
Warming Up
Start each workout with 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training Zone Exercise
After warming up, increase the intensity of your exer-
cise until your pulse is in your training zone for 20 to 60
minutes. (During the first few weeks of your exercise
program, do not keep your pulse in your training zone
for longer than 20 minutes.) Breathe regularly and
deeply as you exerciseÑnever hold your breath.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use stored
fat calories for energy. If your goal is to burn fat, adjust
the speed and incline of the treadmill until your heart
rate is near the low end of your training zone. (See
pages 8 and 9.)
Cool-down
Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
muscles and will help prevent post-exercise problems.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exercise
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown in the
drawings at the right. Move slowly as you stretchÑnever
bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for both legs. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
4
With one leg in front of the other, reach forward and place
your hands against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front leg, lean for-
ward and move your hips toward the wall. Hold for 15 counts,
then relax. Repeat 3 times for both legs. To cause further
stretching of the achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for both legs. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees out-
ward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. WLTL27081
R0899A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
4
1
2
1
4
1
4
6
1
1
1
1
1
4
2
1
1
1
3
1
1
1
1
1
1
1
1
13
1
1
9
1
4
1
1
2
2
1
2
5
2
2
7
2
1
1
1
1
1
1
4
1
1
1
2
12
Handrail Bolt
Incline Leg
Handrail Spacer
Left handrail
Handrail Screw
Key/Clip
Electronic Screw
Console Screw
Speed Potentiometer
Speed Control
Console Assembly
Battery Cover
Latch Spacer
Latch Screw
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105*
#
1
2
1
2
1
2
1
1
1
1
1
1
1
4
2
1
2
2
2
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
2
4
2
2
1
1
1
1
1
1
1
Choke
Belt Guide
Belly Pan
Isolator
Incline Leg Bolt
Ratchet Screw
Ratchet Spring Screw
Ratchet
Ratchet Spring
Incline Leg Spacer (long)
Console Base
Wire Tie
Wire Tie Clamp
Handrail Washer
Incline Leg Spacer (short)
Incline Leg Plate
Incline Wheel Bolt
Incline Wheel
Incline Wheel Nut
Ground Screw
Ground Wire
Rear Roller Adj. Bolt
Rear Endcap
Adhesive Clip
Allen Wrench
Latch Decal
Rear Roller
Frame
Rear Platform Screw
Left Foot Rail
Console Base
Magnet
Reed Switch
Front Roller/Pulley
Sensor Clip
Walking Platform
Walking Belt
Ratchet Screw
Leg Endcap
Frame Guide
Console Rack
Upright Grommet
Upright Endcap
Frame Guide Screw
Console Rack Screw
Roller Guard
9
10
11*
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
Latch Spring
Latch Bracket
Storage Latch
Motor Belt
Motor Tension Bolt/Incline Leg Bolt
Motor Tension Washer
Tension Star Washer
Motor Pivot Nut
Motor/Pulley/Flywheel/Fan
Pulley/Flywheel/Fan
Motor
Motor Pivot Bolt
8Ó Cable Tie
Screw
Hood
Hood Shield
Small Screw
Right Handrail
Base Pad
Motor Belly Pan
Controller
Frame Pivot Bolt
Frame Pivot Washer
Upright Base
Base Leg Screw
Washer
Wheel Bolt
Wheel
Wheel Nut/Incline Nut
Base Leg
Circuit Breaker
Grommet
Power Cord
Harness Clip
Motor Tension Nut
Shock
Right Frame Spacer
Latch Assembly
14Ó White Wire, Pig Tail
8Ó Blue Wire, Pig Tail
8Ó Red Wire, Male/Female
UserÕs Manual
Right Foot Rail
Platform Screw
Front Roller Adj. Bolt
Wire Harness
Left Frame Spacer
Oval Isolator
#
#
#
* Includes all parts shown in the box
# These parts are not illustrated
Belly Pan Fastener
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
¥ The MODEL NUMBER of the product (WLTL27081).
¥ The NAME of the product (WESLO CADENCE¨ 1010 treadmill).
¥ The SERIAL NUMBER of the product (see the front cover of this manual).
¥ The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).
WESLO is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center, products used
for commercial or rental purposes, or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other con-
sequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 148161 H02005-C R0899A
Printed in USA © 1999 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|