Model No. WETL14906.0
Serial No.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts,
please call:
08457 089 009
or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: [email protected]
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. If an extension cord is needed, use only a 3-
2
conductor, 1mm (14-gauge) cord that is no
longer than 1.5 m (5 ft.).
2. Use the treadmill only as described in this
manual.
12. Keep the power cord away from heated sur-
faces.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on a surface that blocks any air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See MAIN-
TENANCE AND TROUBLESHOOTING on page
17 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Read, understand, and test the emergency
stop procedure before using the treadmill (see
OPERATION AND ADJUSTMENT on page 10).
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should be used only by persons
weighing 113 kg (250 lbs.) or less.
17. Never leave the treadmill unattended while it is
running. Always remove the key and unplug
the power cord when the treadmill is not in use.
8. Never allow more than one person on the
treadmill at a time.
18. The pulse sensor is not a medical device.
Various factors, including your movement, may
affect the accuracy of heart rate readings. The
pulse sensor is intended only as an exercise
aid in determining heart rate trends in general.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes; never use the treadmill with bare feet,
wearing only stockings, or in sandals.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 15.)
You must be able to safely lift 20 kg (45 lbs.) to
raise, lower, or move the treadmill.
10. When connecting the power cord (see page
10), plug the power cord into an earthed cir-
cuit. No other appliance should be on the
same circuit. When replacing the fuse, an
ASTA approved BS1362 type should be fitted
to the fuse carrier. A 13 amp fuse should be
used.
20. When folding or moving the treadmill, make
sure that the frame is securely held by the
lock pin.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Do not change the incline of the treadmill by
placing objects under the treadmill.
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. Inspect and properly tighten all parts of the
treadmill regularly.
23. Never drop or insert any object into any
opening.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
24.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has been placed on the
treadmill. If the decal is missing, or if it is not legible,
call the telephone number on the front cover of this
manual and order a free replacement decal. Apply the
decal in the location shown. Note: The decal is not
shown at actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new WESLO® CADENCE
S 6 treadmill. The CADENCE S 6 treadmill combines
advanced technology with innovative design to make
your workouts at home more effective and enjoyable.
And when you’re not exercising, the CADENCE S 6
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
ing this manual, please see the front cover of this man-
ual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number of the treadmill is WETL14906.0.
The serial number can be found on a decal attached to
the treadmill (see the front cover of this manual for the
location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Water Bottle Holder
(Bottle is not included)
Console
Key/Clip
Handrail
Storage Latch
Hood
On/Off Switch
Circuit Breaker
Walking Belt
Foot Rail
Wheel
RIGHT SIDE
Incline Leg
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant
on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
In addition to the included hex key
spanners
, assembly requires a phillips screwdriver
.
, two
, and wire cutters
Note: To identify small parts used during assembly, see the PART IDENTIFICATION CHART in the center of
this manual. Some parts may be preassembled.
1. Have a second person hold the Base (52) in the position
1
shown.
Identify the Left Upright (53) (the Right Upright [54] has a
large hole near the lower end).
52
Hold the Left Upright (53) so the bend is in the posi-
tion shown. Attach the Left Upright to the Base (52) with
two Upright Bolts (2). Do not tighten the Upright Bolts
yet.
54
2
Large
Hole
Attach the Right Upright (54) to the Base (52) in the same
way.
2
53
Bend
2. Slide the two Wheel Housings (62) onto the Base (52),
with the heads of the Wheel Bolts (35) on the outside as
shown. Attach each Wheel Housing with two Wheel
Housing Bolts (6), two Wheel Housing Washers (11), and
two Wheel Housing Nuts (15).
2
35
62
15
6
11
35
62
15
52
11
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. With the help of a second person, raise the Uprights
(53, 54) so the Base (52) is flat on the floor as shown.
Next, position the front of the treadmill Frame (51) between
the Uprights.
3
Hole
See the inset drawing. Locate the wire inside the lower
end of the Right Upright (54). Secure the wire to the Wire
Harness (98). Next, locate the opposite end of the wire,
which is extending from the upper end of the Right
Upright. Pull the wire until the end of the Wire Harness is
extending from the indicated hole in the Right Upright.
53
54
111
Have a second person lift and hold the front end of the
Frame (51). Hold a Frame Spacer (111) between the Right
Upright (54) and the Frame. Attach the Right Upright and
the Frame Spacer to the Frame with a Frame Pivot Bolt
(1), a Frame Washer (14), and a Frame Star Washer (9).
98
14
1
Repeat this step on the left side of the treadmill. Note:
There is not a wire on the left side of the treadmill.
9
52
Remove the wire from the Wire Harness (98).
51
Wire
54
98
4. Turn the Console Assembly (91) face-down. Be careful
4
not to scratch the face of the Console Assembly.
5
Identify the Right Handrail (55), which has a large hole in
one side.
12
4
Attach the Right Handrail (55) to the Console Assembly
(91) with two Console Screws (4), a Crossbar Screw (5),
and a Crossbar Star Washer (12).
Large Hole
55
91
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place the Left Handrail (56) on the Console Assembly
(91). Attach the end of the console ground wire to the in-
dicated small hole in the Left Handrail with the Silver
Ground Screw (8).
5
5
12
56
4
Then, attach the Left Handrail (56) to the Console
Assembly (91) with two Console Screws (4), a Crossbar
Screw (5), and a Crossbar Star Washer (12). Be careful
not to pinch the ground wire.
Console Ground Wire
8
Small
Hole
91
6. Hold the Console Assembly (91) near the Right Upright
(54). Touch the Right Handrail (55) to discharge any
static.
6
Connector
91
Insert the end of the Wire Harness (98) into the hole in
the bottom of the Right Handrail (55) and out of the large
hole in the side. Then, insert the end of the Wire Harness
through the two looped plastic ties.
Press the end of the Wire Harness (98) into the indicated
connector on the back of the Console Assembly (91).
The end of the Wire Harness should slide easily into
the connector and snap into place. If it does not, turn
the end of the Wire Harness and then insert it. IF THE
CONNECTOR IS NOT INSERTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE POWER IS
TURNED ON.
98
Plastic
Ties
55
98
54
7. Insert the excess Wire Harness (98) down into the Right
Upright (54). Then, tighten the two plastic ties around the
Wire Harness, and cut off the ends of the plastic ties.
7
54
Plastic
Ties
98
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Set the Console Assembly (91) on the Right Upright (54)
and the Left Upright (not shown). Next, finger tighten four
Handrail Bolts (3) with four Handrail Washers (13) and
four Handrail Star Washers (10) (only two of each are
shown) into the Right Upright and the Left Upright. Then,
tighten all four Handrail Bolts.
8
Slot
91
54
7
Attach the Console Back (93) to the Console Assembly
(91) with four Console Back Screws (7). Make sure that
the Wire Harness (98) is in the indicated slot in the
Console Back and that no wires are pinched.
93
7
98
10
13
3
9. Carefully lower the Handrails (55, 56) to the floor. Center
the Frame (51) between the Handrails, and tighten the
four Upright Bolts (2). Then, raise the Handrails back to
the vertical position.
9
2
51
See the inset drawing. Attach the Latch Assembly (108) to
the Left Upright (53) with two Latch Screws (7). Make
sure that the Latch Assembly is oriented as shown.
55, 56
53
108
7
10.Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt
(see page 18). To protect the floor or carpet, place a mat under the treadmill.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-
cone spray or other substances to the walking belt or the walking platform. Such substances will deterio-
rate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric cur-
1
Socket on treadmill
rent to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug. Important: If the power cord is damaged, it must
be replaced with a manufacturer-recommended power cord.
See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill.
See drawing 2. Press the pins on the power cord into the metal clips
2
in the adapter as shown. Close the adapter cover over the end of the
power cord and tighten the screw in the adapter. Important: Make
sure that the adapter cover is secure and the screw has been
tightened before using the power cord.
Adapter
Cover
Screw
Pins
Adapter
Metal
Clips
See drawing 3. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with
GFCI-equipped outlets.
3
Outlet
DANGER:
Improper connection of the equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Key
Note: If there are sheets of clear plastic
on the console, remove the plastic.
Clip
FEATURES OF THE CONSOLE
HOW TO TURN ON THE POWER
The treadmill console offers a selection of features
designed to make your workouts more effective.
Plug in the power cord (see
page 10). Next, locate the
on/off switch on the treadmill
frame near the right upright.
Make sure that the switch is
in the “on” position.
On
Position
When you select the manual mode of the console, you
can change the speed and incline of the treadmill with
the touch of a button. As you exercise, the displays will
provide continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothes. Then,
insert the key into the console. After a moment, the dis-
plays will light. Important: In an emergency situa-
tion, the key can be pulled from the console, caus-
ing the walking belt to slow to a stop. Test the clip
by carefully taking a few steps backward; if the key
is not pulled from the console, adjust the position
of the clip.
The console also offers four speed programs. Each
program automatically controls the speed of the tread-
mill as it guides you through an effective workout.
To prevent damage to the walking platform, always
wear clean athletic shoes while using the treadmill.
During the first few minutes that the treadmill is
used, inspect the alignment of the walking belt, and
center the walking belt if necessary (see page 18).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow your progress with the track and the
displays.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
5
The track—The track
represents a distance of
400 meters (1/4 mile).
As you walk or run on
1
See HOW TO TURN ON THE POWER on page
11.
the treadmill, the indica-
tors around the track will
Select the manual mode.
2
3
appear in succession until the entire track ap-
pears. The track will then disappear and the indi-
cators will again begin to appear in succession.
The center of the track will show the number of
laps that you have completed.
When the key is in-
serted, the manual
mode will be selected.
If you have selected a
speed program, rese-
lect the manual mode
by pressing the Program Select button repeatedly
until only zeros appear in the displays.
The lower left
display—As you exer-
cise, the lower left dis-
play can show the
elapsed time and the
distance that you have
walked or run.
Start the walking belt.
To start the walking belt, press the Start button,
the Speed increase button, or one of the num-
bered speed buttons.
The lower right
display—The lower right
display can show the
speed of the walking belt
and the approximate
number of calories that
you have burned. The display also shows your
heart rate when you use the handgrip pulse sen-
sor (see step 6 on page 13).
If you press the Start button or the Speed in-
crease button, the walking belt will begin to move
at 2 Km/H. As you exercise, change the speed of
the walking belt as desired by pressing the Speed
increase and decrease buttons. Each time you
press a button, the speed setting will change by
0.1 Km/h; if you hold down a button, the speed
setting will change in increments of 0.5 Km/h.
Note: After you press the buttons, it may take a mo-
ment for the walking belt to reach the selected
speed setting.
The upper display—
The upper display can
show the elapsed time,
the distance that you
have walked or run, the
speed of the walking
If one of the numbered speed buttons is pressed,
the walking belt will gradually change speed until it
reaches the selected speed setting.
belt, or the approximate number of calories you
have burned. Press the Priority Display button re-
peatedly until the upper display shows the informa-
tion that you are most interested in viewing. Note:
While information is shown in the upper display,
the same information will not be shown in the
lower displays.
To stop the walking belt, press the Stop button.
The time will begin to flash in one of the displays.
To restart the walking belt, press the Start button or
the Speed increase button.
Change the incline of the treadmill as desired.
4
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
To change the incline of the treadmill, hold down
the Incline increase or decrease button until the
desired incline level is reached.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The console can
display speed and dis-
tance in either kilome-
ters or miles. To see
which unit of measure-
ment is selected, first
remove the key from the console. Next, hold down
the Stop button, reinsert the key, wait until you
hear a tone, and then release the Stop button. An
“M” for metric kilometers or an “E” for English miles
will appear in the upper display. Press the Speed
increase button to change the unit of measurement
if desired. When the desired unit of measurement
is selected, remove the key and then reinsert it.
To measure your heart rate, stand on the foot
rails and hold the metal contacts—avoid moving
your hands. When your pulse is detected, the
small heart symbol in the lower right display will
flash, one or two dashes will appear, and then
your heart rate will be shown. For the most accu-
rate heart rate reading, continue to hold the
contacts for about 15 seconds.
When you are finished exercising, remove the
key from the console.
7
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in a
secure place. Then, switch the on/off switch to the
“off” position and unplug the power cord.
Measure your heart rate if desired.
6
Before using the hand-
grip pulse sensor, re-
move the sheets of
clear plastic from the
metal contacts. In addi-
tion, make sure that
your hands are clean.
Metal
Contacts
13
Download from Www.Somanuals.com. All Manuals Search And Download.
one of the displays to alert you, and then the
speed of the walking belt will change. The pro-
gram will continue until all 30 periods are com-
pleted. The walking belt will then slow to a stop.
HOW TO USE A SPEED PROGRAM
Insert the key into the console.
1
If the speed setting is too high or too low during the
program, you can manually override the setting by
pressing the Speed buttons. However, when the
next period begins, the speed of the walking
belt will change if a different speed setting is
programmed for the next period.
See HOW TO TURN ON THE POWER on page
11.
Select one of the four speed programs.
2
To select a speed pro-
gram, press the
Program Select button
repeatedly; “P-1,” “P-2,”
“P-3,” or “P-4” will ap-
To stop the program, press the Stop button. The
time will begin to flash in one of the displays. To
restart the program, press the Start button or the
Speed increase button. The walking belt will begin
to move at 2 km/h. When the next period begins,
the speed of the walking belt will change if a differ-
ent speed setting is programmed for the next pe-
riod.
pear in the upper dis-
play for a few seconds to show which program is
selected. The maximum speed setting of the se-
lected program will also flash in one of the dis-
plays for a few seconds.
Change the incline of the treadmill as desired.
Each program consists of 30 one-minute periods.
One speed setting is programmed for each period.
Note: The same speed setting may be pro-
grammed for two or more consecutive periods.
The profiles on the console show how the speed
of the walking belt will change during the pro-
grams.
4
5
See step 4 on page 12.
Follow your progress with the track and the
displays.
See step 5 on page 12.
Press the Start button or the Speed increase
button to start the program.
3
Measure your heart rate if desired.
See step 6 on page 13.
6
7
When you press either button, the treadmill will
automatically adjust to the speed setting that is
programmed for the first period of the program.
Hold the handrails and begin walking.
When you are finished exercising, remove the
key.
When the first period ends, a series of tones will
sound. If a different speed setting is programmed
for the second period, the speed setting will flash in
See step 7 on page 13.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Unplug the power cord. CAUTION: You must be able to
safely lift 20 kg (45 lbs.) to raise, lower, or move the
treadmill.
Frame
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the pos-
sibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight. As you raise the frame, make sure to lift
with your legs rather than your back. Raise the frame
about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the catch is
past the latch pin. Then, slowly release the latch knob;
make sure that the latch pin is resting against the
catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 30°C (85°F).
Latch Pin
Latch Knob
Catch
HOW TO MOVE THE TREADMILL
Frame
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
pin is resting against the catch.
1. Hold the handrails and place one foot against one of the
wheels. Do not pull back on the frame.
Handrail
Wheel
2. Tilt the treadmill back until it rolls freely on the wheels, and
carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is in the storage position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left hand, pull the latch knob to the left
and hold it. Lower the frame until it is past the latch pin.
Then, release the latch knob.
Latch Pin
Latch Knob
Catch
2. Hold the frame firmly with both hands, and lower it to the
floor. To decrease the possibility of injury, bend your
legs and keep your back straight.
Frame
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 10). If an exten-
sion cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m
(5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the circuit breaker located on the treadmill
c
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
Tripped
Reset
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the “on”
position.
d
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill near the power cord (see c. above). If the cir-
cuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the on/off switch is in the “on” position (see d. above).
e. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
20
65
POWER CORD. Remove the five indicated Screws
(20) and the two Foot Rail Screws (25). Then, care-
fully remove the Hood (65).
20
20
25
Locate the Reed Switch (97) and the Magnet (105) on
the left side of the Pulley (104). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 3 mm (1/8 in.). If necessary,
loosen the Screw (21), move the Reed Switch slightly,
and then retighten the Screw. Reattach the Hood (not
shown), and run the treadmill for a few minutes to
check for a correct speed reading.
3 mm
21
104
105
97
Top View
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
5–7cm
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller bolts counterclockwise, 1/4 of a turn. When
the walking belt is properly tightened, you should be
able to lift each edge of the walking belt 5 to 7 cm (2
to 3 in.) off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is properly
tightened.
Rear Roller
Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first re-
a
move the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller bolt
clockwise 1/2 of a turn. Be careful not to overtighten
the walking belt. If the walking belt has shifted to
the right, turn the left rear roller bolt counterclockwise
1/2 of a turn. Then, plug in the power cord, insert the
key, and run the treadmill for a few minutes. Repeat
until the walking belt is centered.
b. If the walking belt slips when walked on, first re-
b
move the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller bolts
clockwise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each edge
of the walking belt 5 to 7 cm (2 to 3 in.) off the walking
platform. Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key, and
carefully walk on the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-
exercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WETL14906.0
R0706A
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
4
5
6
7
2
4
4
4
2
4
6
Frame Pivot Bolt
Upright Bolt
Handrail Bolt
42
4
Electronics Star
Washer
Incline Leg Wheel
Motor Tension Nut
Frame Pivot Nut
Nut
Hood Clip
Handrail Nut
Small Nut
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
#
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Grommet
Stop Bracket
Controller
Transformer
Filter
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
2
2
2
5
5
4
3
2
1
1
1
1
1
1
1
1
1
1
Console Screw
Crossbar Screw
Wheel Housing Bolt
Latch Screw/
Console Back Screw
Silver Ground Screw
Frame Star Washer
Handrail Star Washer
Wheel Housing
Washer
Crossbar Star Washer
Handrail Washer
Frame Washer
Wheel Housing Nut
Lift Motor Bolt
6 mm Hex Key
4 mm Hex Key
Roller Bracket Screw
Hood Screw
Power Cord
Console Assembly
Console Crossbar
Console Back
Wheel Nut
Ground Wire
Ground Wire
8
9
10
11
1
2
4
4
Isolator Fastener
Frame
Base
Left Upright
Right Upright
Right Handrail
Left Handrail
Electronics Bracket
Dust Guard
Motor Bracket
Left Rear
Roller Bracket
Right Rear
Roller Bracket
Wheel Housing
Base Pad
Latch Catch
Hood
Belly Pan
Left Foot Rail
Right Foot Rail
Incline Leg
Reed Switch
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
2
4
2
4
2
1
1
2
5
13
1
1
2
10
4
Wire Harness
Outlet Plate Assembly
Walking Platform
Walking Belt
Lift Motor Nut
Belt Guide
Front Roller/Pulley
Magnet
Motor Belt
61
1
Screw
Rear Roller
Latch Assembly
Key/Clip
Front Roller Adj. Bolt
Ground Screw
Outlet Plate Bolt
Foot Rail Screw
Base Pad Screw
Rear Walking
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
2
4
1
1
1
1
1
1
2
4
1
2
2
4
4
2
Incline Bolt
Frame Spacer
Power Adapter
Warning Decal
Tie Holder Screw
Lift Belly Pan
Incline Wire
2
Platform Bolt
28
29
30
31
32
33
4
2
2
1
2
2
Belt Guide Screw
Rear Roller Adj. Bolt
Motor Bolt
Motor Pivot Bolt
Incline Leg Bolt
Front Walking
Platform Bolt
Motor Tension Bolt
Wheel Bolt
Rear Roller
Star Washer
Front Roller
Star Washer
Wheel
Wheel Spacer
Motor Isolator
Motor Bushing
Frame Endcap
Upright Endcap
Handrail Endcap
Platform
Cushion, Front
Center Isolator
Drive Motor
Wire Tie
Shield
Incline Motor
6” Red Wire, M/F
4” Black Wire, M/F
4” Blue Wire, M/F
8” Blue Wire, 2F
10” Blue Wire, 2F
6” White Wire, 2F
10” White Wire, 2F
User’s Manual
#
#
#
#
#
#
#
34
35
36
2
2
2
78
79
80
81
82
83
84
2
1
4
4
2
1
1
37
1
38
39
40
41
2
2
1
Motor Star Washer
Outlet Plate Washer
Ground Star Washer
Tek Screw
8” Tie
Tie Holder
Reed Switch Clip
Belly Pan Grommet
#These parts are not illustrated
Specifications are subject to
change without notice.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Remove this chart and use it to identify small parts during assembly. Save this chart and the EXPLODED
DRAWING/PART LIST for future reference.
Console
Screw (4)–4
Crossbar
Screw (5)–2
Silver Ground
Screw (8)–1
Latch/Console
Back Screw
(7)–6
Crossbar Star
Washer (12)–2
Wheel Housing
Washer (11)–4
Upright Bolt (2)–4
Wheel Housing
Nut (15)–4
Handrail Star
Washer (10)–4
Handrail
Washer (13)–4
Wheel Housing Bolt (6)–4
Frame Star
Washer (9)–2
Handrail Bolt (3)–4
Frame Washer
(14)–2
Frame Pivot Bolt (1)–2
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WETL14906.0
R0706A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4, Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Tel:
08457 089 009
Outside the UK: (44) 0113 387 7133
Fax: (44) 0113 387 7125
To help us assist you, please be prepared to provide the following information:
• the MODEL NUMBER of the product (WETL14906.0)
• the NAME of the product (WESLO CADENCE S 6 treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the needed part(s) (see the PART LIST and the EXPLODED
DRAWING in the centre of this manual)
Part No. 237122 R0806A
Printed in China © 2006 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|