Model No. WCTL39100
Serial No.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfac-
tion through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our Customer Hot Line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-888-936-4266
Mon.–Fri., 8 a.m.–6:30 p.m. EST
(excluding holidays)
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Use only a CUL-listed surge protector, rated
at 15 amps, with a 14-gauge cord of five feet
or less in length. Do not use an extension
cord.
continuously for longer than 1 hour.
18. Never leave the treadmill unattended while it
is running. Always remove the key when the
treadmill is not in use.
10. Keep the power cord and the surge protector
away from heated surfaces.
19. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 4 if the tread-
mill is not working properly.)
20. Inspect and tighten all parts of the treadmill
every three months.
12. The roller guards must be 1/8 inch from the
rear roller. Remove the key and adjust the
roller guards, if necessary.
21. To change the incline level of the treadmill,
refer to the instructions on page 9. Do not
attempt to change the incline level in any
other way.
13. Wear appropriate exercise attire when using
the treadmill. Do not wear loose clothing that
could become caught in the treadmill.
22. Never drop or insert any object into any
opening.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
23. Always unplug the power cord before per-
forming the maintenance and adjustment
procedures described in this manual. Never
remove the motor hood unless instructed to
do so by an authorized service representa-
tive. Servicing other than the procedures in
this manual should be performed by an
authorized service representative only.
14. Never start the treadmill while you are stand-
ing on the walking belt.
15. Always hold the handrails while exercising
on the treadmill.
16. Adjust the speed in small increments.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
17. To reduce the possibility of the treadmill
overheating, do not operate the treadmill
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the WESLO CADENCE® 391
treadmill. The natural motion and versatility of tread-
mills have made them the most popular way to get an
effective cardiovascular workout. The CADENCE 391
treadmill blends advanced technology with innovative
design to let you enjoy this effective exercise in the
convenience and privacy of your home. Feel better,
look better, and be healthier in just a few minutes a
day.
please call our Customer Service Department toll-free
at 1-888-936-4266, Monday through Friday, 8 a.m.
until 6:30 p.m. Eastern Standard Time (excluding holi-
days). To help us assist you, please note the product
model number and serial number before calling. The
model number is WCTL39100. The serial number can
be found on a decal attached to the treadmill (see the
front cover of this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Console
Towel Rack
Pulse Sensor
Speed Control
Key/Clip
Upright
Handrails
FRONT
Circuit Breaker
Motor Hood
Walking Belt
Power Cord
Roller Guards
Incline Pin
Foot Rail
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolt
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until
assembly is completed. Refer to the drawings below to identify small parts used in assembly. Assembly requires
an adjustable wrench
(not included).
3/8" x 1" Bolt (18)–1
3/8" Flange Nut (48)–2
3/8" x 1 1/2" Washer
(28)–1
3/8" x 2 3/4" Bolt (49)–2
3/8" x 1 3/4" Bolt (2)–2
1. Raise the Upright (11) to the vertical position. Insert the 3/8” x 1”
Bolt (18) and the 3/8” x 1 1/2” Washer (28) into the lower end of
the Upright. Finger tighten the Bolt into the Frame (59).
1
11
18
28
59
2. Hold the upper end of the Right Handrail (10) under the
Console (3). Insert a 3/8” x 1 3/4” Bolt (2) up into the Handrail,
and finger tighten the Bolt into the plate under the Console.
2
3
1
Attach the Left Handrail (1) in the same manner.
2
10
3. Insert a 3/8” x 2 3/4” Bolt (49) into the lower end of the Right
Handrail (10) and through the Frame (59). Reach under the
Frame and tighten a 3/8” Flange Nut (48) onto the Bolt.
3
59
Attach the Left Handrail (not shown) in the same manner.
10
Tighten all Bolts used in steps 1 and 2.
49
48
4. Remove the paper backing from the Adhesive Clip (64). Press
the Adhesive Clip onto the Right Endcap (63) in the indicated
location. Press the 3/16” Allen Wrench (65) into the Adhesive
Clip.
4
63
65
64
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The Console (3) requires two "AA" batteries (not included).
Alkaline batteries are recommended.
5
3
15
Slide the Battery Cover (15) up as shown. Press two batteries into
the battery compartment, with the negative (–) ends of the batteries
touching the springs. Close the battery cover.
Batteries
6. Make sure that all parts are tightened before you use the treadmill. Note: To protect the floor or carpet from
damage, place a mat beneath the treadmill.
PROPER EXERCISE FORM
The instructions on pages 7 to 9 of this manual explain the operation and adjustment of the treadmill. For maxi-
mum treadmill performance, it is important to maintain proper form when walking on the treadmill. The drawing
below demonstrates the proper form. Be sure to remember the following important guidelines:
• Always hold the handrails when stepping on
and off the treadmill, and when exercising on
the treadmill.
• Always stand on the foot rails when turning on
the power or starting the walking belt. The walk-
ing belt may not start while you are standing on it.
• While walking on the treadmill, rest your hands
on the handrail, keep your back straight, and
lean forward slightly. Do not lean back or push
forward against the walking belt with your feet. If
you slow the walking belt with your feet, it may
come to a stop. If this happens, stand on the foot
rails until the walking begins to move again.
• To change the incline level of the treadmill,
refer to page 9. Do not attempt to change the
incline level any other way. The incline range of
the treadmill is 11% to 14%. This range is ideal for
maximum treadmill performance.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
risk of electric shock. This product is equipped with a
cord having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. They will deteriorate the walking belt and
cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole recep-
tacle as shown in drawing 2 if a properly grounded out-
let is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on
or off. To decrease the
1
possibility of your
treadmill being dam-
aged, always use a
surge protector (not
included) with your
treadmill.
Grounded Outlet Box
Treadmill Power Cord
Grounding Pin
Grounding
Plug
Grounding
Pin
Surge protectors are
sold at most hardware
stores and department
stores. Use only a CUL-
listed surge protector,
rated at 15 amps, with a
14-gauge cord of five
feet or less in length.
Grounding
Plug
Grounded Outlet
2
Grounded Outlet Box
Adapter
Grounding Pin
Grounding
This product must be
grounded. If it should
malfunction or break
down, grounding pro-
vides a path of least
resistance for electric
current to reduce the
Surge Protector
Plug
Lug
Metal Screw
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
Pulse Display
Speed Control
Monitor Display
On/Off
Button
Scan
Button
Note: If there is a thin sheet of clear
plastic on the console, remove it.
Clip
Pulse Sensor
Key
Insert the key fully into the power switch.
1
CAUTION:Before operating the con-
sole, read the following important precautions.
Note: The two dis-
plays will not
appear when the
key is first insert-
ed.
• Do not stand on the walking belt when turning
on the power.
• Always wear the clip while operating the tread-
mill. When the key is removed from the con-
sole, the power will shut off.
Key
• After the speed control is moved, there will be
a pause before the walking belt begins to move.
Press the ON/OFF button.
2
3
The two displays
will appear. Note:
If batteries were
just installed, the
displays will
• Adjust the speed in small increments until you
are familiar with the treadmill.
• The training zones marked above the speed
control are guidelines only. Read CONDITION-
ING GUIDELINES on pages 12 and 13 to deter-
mine the proper exercise level.
already appear.
Reset the speed control and start the walking
belt.
• To reduce the risk of electric shock, keep the
console dry. Avoid spilling liquid on the con-
sole and use only a sealed water bottle.
Slide the speed
control fully to the
left, to the
"RESET" position.
Next, slide the
control to the right
until the walking
belt begins to
STEP BY STEP CONSOLE OPERATION
Make sure that the power cord is properly plugged in
(see HOW TO PLUG IN THE POWER CORD on page
7). Next, step onto the foot rails of the treadmill. Find
the clip attached to the key (see the drawing above).
Slide the clip onto your waistband. Follow the steps on
pages 8 and 9 to operate the console.
move at a slow speed.
Carefully step onto the walking belt and begin walk-
ing. Change the speed of the walking belt as
desired by sliding the speed control. Note: To stop
8
Download from Www.Somanuals.com. All Manuals Search And Download.
the walking belt, slide the speed control to the
"RESET" position.
pulse display flashes steadily. Hold your thumb at
this level. After 5 to 10 seconds, your pulse will be
displayed. Hold your thumb on the sensor for
another 15 seconds for the most accurate reading.
If the displayed pulse appears to be too high or too
low, or if your pulse is not displayed, lift your thumb
off the sensor and allow the display to reset. Press
down again on the sensor as described above.
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of
pressure. Try the sensor several times until you
become familiar with it. Always stand still while
measuring your pulse.
Press the MODE button to select the desired
monitor mode.
4
The monitor offers
five different modes
to provide instant
exercise feedback:
Mode
SPEED—displays
your speed, in miles
per hour.
Indicators
When you are finished, stop the walking belt
and remove the key.
TIME—displays the elapsed time.
6
7
DISTANCE—displays the distance that you have
walked or run, in miles.
Slide the speed control to the “RESET” position,
and remove the key. Store the key in a secure loca-
tion.
CALORIES—displays the approximate number of
Calories you have burned. Note: The actual number
of Calories you have burned may differ slightly from
the number displayed if the speed or incline is near
the lowest or highest setting.
Press the ON/OFF button.
To turn off the displays, press the on/off button.
Note: If the walking belt is stopped and the console
buttons are not pressed for 3 to 6 minutes, the dis-
plays will turn off automatically.
SCAN—displays the SPEED, TIME, DISTANCE,
and CALORIES modes, for five seconds each, in a
repeating cycle.
When the power is turned on, the SCAN mode will
automatically be selected. One mode indicator (see
the drawing above), will appear by the scan symbol,
and a second mode indicator will show which mode
is currently displayed.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity
1
Incline Pin
Incline Leg
of your exercise, the
incline of the tread-
mill can be
Frame
If desired, the SPEED, TIME, DISTANCE or
CALORIES mode can be displayed continuously.
Press the MODE button repeatedly until the mode
indicator by the scan symbol disappears, and a mode
indicator appears by the symbol of the desired
mode.
changed. There are
three different
incline levels.
Before changing
the incline, remove
the key and
2
unplug the power
cord.
Note: The monitor displays can be reset by press-
ing the on/off button twice.
Incline Pin
Measure your pulse, if desired.
To change the
incline, carefully lay
the treadmill on its
left side. Remove the incline pin from the right incline leg
as shown in drawing 1. Adjust the incline leg to the
desired height and fully re-insert the incline pin. Make
sure the incline pin is in the “locked” position shown in
drawing 2. Lay the treadmill on its right side. Repeat the
procedure for the left incline leg.
5
To use the pulse
sensor, stand on the
foot rails and place
your thumb on the
pulse sensor as
shown. The pulse
sensor is pressure-
activated. Fully
Pulse Sensor
press down the
CAUTION: Before using the treadmill, make sure
that both incline pins are fully inserted at the same
height. Do not use the treadmill with the incline pins
removed.
pulse sensor. Do not press too hard, or the circu-
lation in your thumb will be restricted, and your
pulse will not be detected. Next, slightly raise
your thumb until the heart-shaped indicator in the
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-SHOOTING AND STORAGE
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies to your treadmill and follow the steps listed. If further assistance is needed, please call our
Customer Service Department toll-free at 1-888-936-4266, Monday through Friday, 8 a.m. until 6:30 p.m.
Eastern Standard Time (excluding holidays).
1. SYMPTOM: THE POWER DOES NOT TURN ON
a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into
a properly grounded outlet (see HOW TO PLUG IN THE POWER CORD on page 7). Use only a UL-listed
surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console (see step
1 on page 8).
c. Check the circuit breaker located on the treadmill frame near
the power cord. If the switch protrudes as shown, the circuit
breaker has tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
Tripped
Reset
2. SYMPTOM: THE POWER TURNS OFF DURING USE
a. Check the circuit breaker located on the treadmill frame near the power cord. If the circuit breaker has
tripped, the switch will protrude (see the drawing above). To reset the circuit breaker, wait for five minutes
and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console (see Step 1 on page 8).
3. SYMPTOM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY
a. Check the batteries in the console (see assembly step 5 on page 6). Most problems are the result of drained
batteries.
b. If the speed display does not show a correct reading, remove
the key and UNPLUG THE POWER CORD. Remove the four
b
1/8”
73
screws from the sides and front of the hood. Carefully remove
the hood. Locate the Reed Switch (73) and the Magnet (75) on
the left side of the Pulley (43). Turn the Pulley until the Magnet
is aligned with the Reed Switch. Make sure that the gap
between the Magnet and the Reed Switch is about 1/8”. If
necessary, loosen the Screw (53) and move the Reed Switch
slightly. Retighten the Screw. Re-attach the hood and run the
treadmill for a few minutes to check for a correct speed reading.
43
75
53
Top
View
4. SYMPTOM: THE WALKING BELT SLOWS OR STOPS WHEN WALKED ON
a. Use only a CUL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.
b. Increase the incline of the treadmill (see HOW TO CHANGE THE INCLINE OF THE TREADMILL on page 9).
c. Make sure that you are using proper form when walking on the treadmill (see PROPER EXERCISE FORM
on page 6).
d. If the walking belt still slows when walked on, please call our Customer Service Department.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5. SYMPTOM: THE WALKING BELT IS OFF-CENTER
a. If the walking belt has shifted to the left, first remove the key and
UNPLUG THE POWER CORD. Using the allen wrench, turn the
rear roller adjustment bolt clockwise 1/4 of a turn. Plug in the
power cord, insert the key and run the treadmill for a few min-
utes. Repeat until the walking belt is centered.
a
b. If the walking belt has shifted to the right, first remove the key
and UNPLUG THE POWER CORD. Using the allen wrench, turn
the rear roller adjustment bolt counterclockwise 1/4 of a turn.
Plug in the power cord, insert the key and run the treadmill for a
few minutes. Repeat until the walking belt is centered.
b
STORAGE
Unplug the power cord when the treadmill is not in use.
Remove the bolt and nut from the lower end of each handrail.
Remove
Remove the bolt from the upper end of each handrail.
Remove
Remove the bolt and washer from the lower end of the upright. Lay
the upright on the treadmill. Keep all bolts and washers in a
secure location.
Remove
Remove the batteries from the console and cover the treadmill dur-
ing extended periods of storage.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
Training Zone (Beats/Min.)
WARNING:
Before beginning
Unconditioned
Conditioned
Age
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
20
25
30
35
40
45
50
55
60
65
70
75
80
85
138-167
136-166
135-164
134-162
132-161
131-159
129-156
127-155
126-153
125-151
123-150
122-147
120-146
118-144
133-162
132-160
130-158
129-156
127-155
125-153
124-150
122-149
121-147
119-145
118-144
117-142
115-140
114-139
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
The following guidelines will help you to plan your exer-
cise program. Remember—these are general guide-
lines. For more detailed information about exercise,
obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether you want to burn fat or strengthen your car-
diovascular system, you can tailor your exercise to
your specific goals. The key to achieving the desired
results is to exercise with the proper intensity.
pulse can be gradually increased until it is near the mid-
dle of your training zone as you exercise. You can mea-
sure your pulse using the pulse sensor. Exercise for
about four minutes, and then measure your pulse imme-
diately. If your pulse is too high or too low, adjust the
intensity of your exercise. It may also be helpful to set
the speed control on the console halfway between the
Burning Fat
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
If your goal is to burn fat, set the speed control on the
turtle symbol (
) and the rabbit symbol (
) to help
you maintain the proper intensity level. (See page 8.)
console to the turtle symbol ( ) to help you maintain
the proper intensity level (see page 8).
Performance Training
If your goal is high performance athletic conditioning,
set the speed control on the console to the rabbit sym-
Aerobic Exercise
bol (
(see page 8).
) to help you maintain the proper intensity level
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. The proper intensity
level for aerobic exercise can be found by using your
pulse as a guide. As you exercise, your pulse should
be kept at a level between 70% and 85% of your maxi-
mum possible heart rate. This is known as your train-
ing zone. You can find your training zone in the table
at the top of this page. Training zones are listed
according to age and physical condition. During the
first few months of your exercise program, keep your
pulse near the low end of your training zone as you
exercise. After a few months of regular exercise, your
WORKOUT GUIDELINES
When exercising, wear appropriate attire. Always wear
athletic shoes for foot protection. Each workout should
include three basic parts: (1) a warm-up, (2) training
zone exercise, and (3) a cool-down.
Warming Up
Warming up prepares the body for exercise by increas-
ing circulation, delivering more oxygen to the muscles
and raising the body temperature. Begin each workout
with 5 to 10 minutes of stretching and light exercise to
warm up (see SUGGESTED STRETCHES on page 13).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Training Zone Exercise
to cool down. This will increase the flexibility of your
muscles and will help to prevent post-exercise problems.
After warming up, increase the intensity of your exer-
cise until your pulse is in your training zone for 20 to
60 minutes. (During the first few weeks of your exer-
cise program, do not keep your pulse in your training
zone for longer than 20 minutes.) Breathe regularly
and deeply as you exercise—never hold your breath.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may com-
plete up to five workouts each week if desired.
Cooling Down
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
Finish each workout with 5 to 10 minutes of stretching
SUGGESTED STRETCHES
The correct form for several basic stretches is shown in the
drawings below. Move slowly as you stretch—never bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for both legs. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your
back foot flat on the floor. Bend your front leg, lean forward
and move your hips toward the wall. Hold for 15 counts, then
relax. Repeat 3 times for both legs. To cause further stretching
of the achilles tendons, bend your back leg as well. Stretches:
Calves, achilles tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for both legs. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees out-
ward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WCTL39100
R0900A
Key No. Qty.
Description
Key No.
Qty.
Description
1
2
3*
4
5
6
7
8
9
1
2
1
1
2
5
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
4
4
6
1
2
1
1
1
1
1
1
1
2
9
2
2
2
2
1
4
1
1
1
1
Left Handrail
3/8” x 1 3/4” Bolt
Console
Upright Wire Harness
Console Cage Nut
Console Screw
Pot Wire
Console Cable Loom
Key/Clip
Right Handrail
Upright
Motor Swivel Bolt
Upright Cage Nut
Motor Swivel Nut
Battery Cover
Motor
Motor/Pulley/Flywheel
3/8” x 1” Bolt
Motor Tension Washer
Star Washer
Motor Tension Nut
Wire Clip
Hood Anchor
Anchor Screw
Upright Pivot Nut
Upright Pivot Washer
Upright Cable Loom
3/8” x 1 1/2” Washer
Reed Switch Clip
Power Cord
Circuit Breaker
Upright Pivot Bolt
Grommet
Frame Endcap
Screw
Incline Pin
Incline Leg Cap
Incline Leg
Belt Guide
Front Roller Adjustment Bolt
Adjustment Washer
Safety Cover
Front Roller/Pulley
Walking Platform
Walking Belt
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
#
2
1
2
2
1
1
4
5
4
2
1
1
1
1
2
1
1
1
1
1
1
1
1
6
4
1
2
1
1
1
1
1
1
2
2
2
4
9
1
1
1
Foot Rail
Pulley/Flywheel
3/8” Flange Nut
3/8” x 2 3/4” Bolt
Controller
Controller Plate
Plastic Stand-Off
Electric Screw
4” Cable Tie
8” Cable Tie
Tie Holder
Potentiometer
Speed Control
Frame
10
11
12
13
14
15
16
17*
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Rubber Pad
Tension Spring
Roller Ground Wire
Right Endcap
Adhesive Clip
Allen Wrench
Short Roller Adjustment Bolt
Left Endcap
Rear Roller
Platform Screw
Hood Screw
Hood
Roller Guard Screw
Reed Switch/Sensor Wire
Roller Tension Nut
Magnet
Motor Belt
Motor Fan
Long Roller Adjustment Bolt
Roller Guard
Handgrip
3/8” Cap Washer
Belt Guide Screw
#8 Flat Washer
8” Green Ground Wire
8” White Wire, Male/Female
User’s Manual
#
#
* Includes all the parts in the box.
# Indicates a non-illustrated part.
Specifications are subject to change without notice. See the back cover for information about ordering replace-
ment parts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WCTL39100
R0900A
15
58
57
3*
6
4
2
5
1
9
18
6
7
6
80
20
5
8
21
14
19
2
17*
6
10
71
11
47
16
77
12
70
70
25
18
26
30
31
28
22
27
26
53
24
23
73
32
29
76
43
75
33
49
13
34
53
40
70
48
41
83
42
44
35
46
46
83
69
72
45
83
35
74
72
41
3
36
61
35
39
79
82
67
81
68
48
37
41
49
59
66
51
53
60
24
53
56
53
50
63
64
55
41
52
62
78
54
65
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-936-4266, Monday through
Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding holidays). When ordering parts, please be pre-
pared to give the following information:
• The MODEL NUMBER of the product (WCTL39100)
• The NAME of the product (WESLO CADENCE® 391 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER of the part(s) (see page 14 of this manual)
• The DESCRIPTION of the part(s) (see page 14 of this manual)
LIMITED WARRANTY
ICON OF CANADA, INC., (ICON), warrants this product to be free from defects in workmanship and materi-
al, under normal use and service conditions, for a period of one (1) year from the date of purchase. This war-
ranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or
repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and
other transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-
authorized by ICON. This warranty does not extend to any product or damage to a product caused by or
attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an
ICON authorized service center, to products used for commercial or rental purposes, or to products used as
store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or conse-
quential damages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder
is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular
purpose is limited in its scope and duration to the terms set forth herein. Some provinces do not allow limita-
tions on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to
province or so specified by the retailer of your equipment.
ICON OF CANADA, INC. 900 de l’Industrie, St. Jérôme, QC J7Y 4B8
WESLO is a registered trademark of ICON Health & Fitness, Inc.
Part No. 167312 R0900A
Printed in Canada © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|