TM
¨
Model No. WLTL25581
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfac-
tion through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
21. When storing the treadmill, make sure that
the storage latch is fully closed.
22. Inspect and tighten all parts of the treadmill
every three months.
16. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
23. The roller guards must be 1/8 inch from the
rear roller (see the drawing on page 4).
Remove the key and adjust the roller guards,
if necessary.
24. Never drop or insert any object into any
opening.
17. To reduce the possibility of the treadmill
overheating, do not operate the treadmill
continuously for longer than one hour.
25.
DANGER:
Always unplug the power
18. Never leave the treadmill unattended while it
is running. Always remove the key when the
treadmill is not in use.
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
19. Do not change the incline of the treadmill by
placing objects under the treadmill.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO MOVE
THE TREADMILL on page 10.) You must be
able to safely lift 45 pounds (20 kg) in order
to raise, lower, or move the treadmill.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or prop-
erty damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has been
placed on your treadmill. If the decal is
missing, or if it is not legible, please call
our Customer Service Department, toll-
free, to order a free replacement decal
(see ORDERING REPLACEMENT PARTS
on the back cover of this manual). Apply
the decal in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the WESLO¨ CADENCE 925
treadmill. The CADENCE 925 treadmill combines
advanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
youÕre not exercising, the unique CADENCE 925 can
be folded up, requiring less than half the floor space of
other treadmills.
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is WLTL25581. The serial
number can be found on a decal attached to the tread-
mill (see the front cover of this manual for the loca-
tion).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Water Bottle Holder
(Bottle not included)
Speed Control
Accessory Tray
Handrails
Console
Key/Clip
Storage Latch
FRONT
Circuit Breaker
Power Cord
Walking Belt
Foot Rails
BACK
Rear Roller
Adjustment Bolts
RIGHT SIDE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
The following tools (not included) are required
for assembly:
¥ Assembly requires two people.
¥ Two (2) adjustable wrenches
¥ One (1) phillips screwdriver
¥ Place all parts in a cleared area and remove the
packing materials; do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, or a set of ratchet wrenches.
¥ As you assemble the treadmill, be sure that all
parts are oriented as shown in the drawings.
1. With the help of a second person, carefully lay the
treadmill on its side. Position one of the Base Legs
(55) on one of the Uprights (37) as shown. Make
sure that the Base Leg Pads (31) and the Front
Wheel (34) are in the indicated positions. Attach the
Base Leg with two Base Leg Bolts (28), two Base
Leg Washers (29), and two Base Leg Nuts (30).
1
28
34
29
31
37
With the help of a second person, carefully turn the
treadmill onto its other side. Attach the other Base
Leg (55) as described above.
55
30
With the help of a second person, carefully raise the
treadmill to the upright position so that both Base
Legs (55) are resting flat on the floor.
2. Hold the treadmill firmly with both hands and lower
the treadmill to the floor. To decrease the possibili-
ty of injury, bend your legs and keep your back
straight.
2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Carefully rotate the Console Base (45) to the posi-
tion shown. Insert two Handrail Bolts (77) through
the Console Base and the Upright (37). The
Handrail Bolts must be inserted from the inside
as shown. Attach a Handrail Nut (86) and Handrail
Washer (85) to each Handrail Bolt.
3
45
85
77
77
86
86
85
37
Tighten all four Handrail Bolts (77) as tightly as
possible. Carefully lift up and push down on the
handrails to make sure that the Console Base
(45) does not move. Regularly inspect and tight-
en all four Handrail Bolts.
45
Handrails
77
77
37
4. Attach the Frame Guide (66) to the left side of the
Frame (21) with two Frame Guide Screws (44) as
shown. Note: Be careful not to overtighten the
Screws. Make sure that the thick end of the
Frame Guide is at the bottom.
4
66
44
21
Thick end
5. Remove the backing from the Adhesive Clip (2).
Press the Adhesive Clip onto the base of the Upright
(37) in the indicated location. Press the Allen
Wrench (35) into the Adhesive Clip.
5
37
2
35
6. The Console (49) requires two "AA" batteries (not
included); alkaline batteries are recommended.
6
49
48
Open the Battery Cover (48) as shown. Press two
batteries into the battery compartment, with the nega-
tive (Ð) ends of the batteries touching the springs.
Close the battery cover, push up on the battery cover
tab, and then push the tab forward as shown in the
inset drawing. Be sure that the tab locks into place.
Battery
Cover Tab
Batteries
7. Make sure that all parts are properly tightened
before you use the treadmill. The use of the remain-
ing parts will be described in other sections of this
manual. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
risk of electric shock. This product is equipped with a
cord having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. They will deteriorate the walking belt and
cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole recep-
tacle as shown in drawing 2 if a properly grounded
outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet
box covers are not grounded. Contact a qualified
electrician to determine if the outlet box cover is
grounded before using an adapter.
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on
or off. To decrease the
possibility of your
1
Grounded Outlet Box
treadmill being dam-
aged, always use a
surge protector (not
included) with your
treadmill.
Treadmill Power Cord
Grounding Pin
Grounding Plug
Grounding Plug
Grounding Pin
Surge protectors are
sold at most hardware
stores and department
stores. Use only a UL-
listed surge protector,
rated at 15 amps, with
a 14-gauge cord of five
feet or less in length.
Grounded Outlet
2
Grounded Outlet Box
Adapter
Grounding Pin
Grounding Plug
This product must be
grounded. If it should
malfunction or break
down, grounding pro-
vides a path of least
resistance for electric
current to reduce the
Surge Protector
Lug
Metal Screw
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
Monitor Display
Pulse Display
Speed Control
PulseSensor
Key
Clip
Follow the steps below to operate the console.
CAUTION: Before operating the
console, read the following precautions.
Insert the key fully into the power switch.
1
Note: Inserting the key
will not turn on the dis-
plays. The displays will
turn on when the
DISPLAY button is
pressed or when the
walking belt is started.
If you just installed bat-
teries, the displays will already be on.
¥ Do not stand on the walking belt when turn-
ing on the power.
¥ Always wear the clip (see the drawing
above) while operating the treadmill. When
the key is removed from the console, the
walking belt will stop.
¥ Adjust the speed in small increments.
¥ The training zones marked below the speed
control are general guidelines only. See
page 14 or more information.
Reset the console and start the walking belt.
2
Move the speed
control to the
RESET position.
Note: Each time
the walking belt
is stopped, the
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and use only a sealable
water bottle.
speed control
must be moved to the RESET position before
the walking belt can be restarted.
STEP BY STEP CONSOLE OPERATION
Before operating the console, make sure that the
power cord is properly plugged in. (See HOW TO
PLUG IN THE POWER CORD on page 7.) In addition,
make sure that batteries are installed in the console.
(See step 6 on page 6.) If there is a thin sheet of clear
plastic on the console, remove it.
Next, slowly move the speed control until the
walking belt begins to move at slow speed.
Carefully step onto the walking belt and begin
exercising. Change the speed of the walking belt
as desired by moving the speed control.
To stop the walking belt, step onto the foot rails
and move the speed control to the RESET position.
Step onto the foot rails of the treadmill. Next, find the
clip attached to the key (see the drawing above). Slide
the clip onto your waistband.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Measure your pulse, if desired.
Follow your progress with the monitor display.
4
3
When you are not using the pulse sensor, a ÒPÓ will
appear in the pulse display. To measure your pulse,
stand on the foot rails and place your thumb on the
pulse sensor as shown. The pulse sensor is pres-
sure activatedÑ
The monitor display
offers six modes
that provide instant
exercise feedback:
¥ SpeedÑThis mode
shows your speed,
in miles per hour.
fully press it
Pulse
Sensor
down. Do not
press too
hard, or the
¥ TimeÑThis mode shows the length of time you
have exercised. Note: If you stop exercising for
ten seconds or longer, the time mode will pause.
circulation in
your thumb
will be restrict-
ed, and your
pulse will not be
detected. Next,
raise your thumb
slightly until the
heart-shaped
Indicator
¥ Distance (DIST)ÑThis mode shows the total
number of miles you have walked or run, up to
999. The display will then reset to zero and con-
tinue counting.
¥ Fat Calories (FAT CALS)ÑThis mode shows the
approximate number of fat calories you have
burned. (See FAT BURNING on page 14.)
indicator in the pulse display flashes steadily. Hold
your thumb at this level. After a few seconds, three
dashes will appear in the display and your pulse
will be shown. Hold your thumb on the sensor for
another 15 seconds for the most accurate reading.
If the displayed pulse appears to be too high or too
low, or if your pulse is not displayed, lift your thumb
off the sensor and allow the display to reset. Press
down again on the sensor as described above.
¥ Calories (CALS)ÑThis mode shows the approxi-
mate number of calories you have burned.
¥ ScanÑThis mode displays the other five modes,
for five seconds each, in a repeating cycle.
When the power is
turned on, the Scan
mode will be select-
ed. One mode indica-
tor will appear by the
word SCAN, and
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of
pressure to the pulse sensor. Try the sensor several
times until you become familiar with it. Remember
to stand still while measuring your pulse.
another mode indica-
tor will show which
mode is currently displayed.
Mode Indicators
Turn off the power.
5
To turn off the power, simply wait for about six
minutes. If the walking belt is not moved and the
DISPLAY button is not pressed for six minutes, the
power will turn off automatically.
If desired, the Speed, Time, Distance, Fat Calories
or Calories mode can be individually selected.
Press the MODE button repeatedly until the
desired mode indicator appears. Make sure that
there is not a mode indicator by the word SCAN.
If desired, the display can be reset by pressing the
DISPLAY button.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
Caution: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown at the right,
and hold the treadmill firmly. Raise the treadmill until the
storage latch locks over the frame guide. Make sure that
the storage latch closes fully over the frame guide.
Storage
Latch
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85¡ Fahrenheit.
Closed
Frame Guide
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
storage latch is locked fully over the frame guide.
1. Hold the upper ends of the handrails. Place one foot on
one of the front wheels as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired loca-
tion. Never move the treadmill without tipping it back,
or the base pads may come off. To reduce the risk of
injury, use extreme caution while moving the tread-
mill. Do not attempt to move the treadmill over an
uneven surface.
Base Leg
Front Wheels
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, slide open the storage
latch. Pivot the treadmill until the frame guide and the
foot rail are past the storage latch.
Storage
Latch
Opened
Frame
Guide
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of
injury, bend your legs and keep your back straight.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is
plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page
7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or
less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole. See step 1 on page 8.
c. Check the circuit breaker located on the treadmill
c
frame near the power cord. If the switch pro-
trudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 8.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 6 on
page 6. Most problems are the result of drained batteries.
b. Remove the six screws from the hood. Carefully
remove the hood. Locate the Reed Switch (17) and
the Magnet (14) on the left side of the Pulley (49).
Turn the Pulley until the Magnet is aligned with the
Reed Switch. Make sure that the gap between
the Magnet and the Reed Switch is about 1/8Ó. If
necessary, loosen the Screw (53) and move the
Reed Switch slightly. Retighten the Screw. Re-
attach the hood, and run the treadmill for a few min-
utes to check for a correct speed reading.
49
53
14
17
1/8Ó
Top View
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt clockwise, and the right bolt counterclock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centered.
a
b
c
b. If the walking belt has shifted to the right, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller
adjustment bolt counterclockwise, and the right bolt
clockwise, 1/4 of a turn each. Be careful not to over-
tighten the walking belt. Plug in the power cord,
insert the key and run the treadmill for a few min-
utes. Repeat until the walking belt is centered.
c. If the walking belt slips when walked on, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller adjust-
ment bolts clockwise, 1/4 of a turn. When the walking
belt is correctly tightened, you should be able to lift
each side of the walking belt 2 to 3 inches off the
walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key and
run the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less
in length.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be
2ÓÐ3Ó
permanently damaged. Remove the key and
UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment bolts coun-
terclockwise, 1/4 of a turn. When the walking belt is
properly tightened, you should be able to lift each
side of the walking belt 2 to 3 inches off the walking
platform. Be careful to keep the walking belt cen-
tered. Plug in the power cord, insert the key and run
the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
Rear Roller
Adjustment Bolts
c. If the walking belt still slows when walked on, please call our toll-free Customer Service
Department.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed of the treadmill until your heart rate is
near the middle of your training zone. It may also be
helpful to set the speed control on the console to AER-
OBIC to help you maintain the proper intensity level.
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
High Performance Athletic Conditioning
If your goal is high performance athletic conditioning, set
the speed control on the console to PERFORMANCE to
help you maintain the proper intensity level. Note: During
the first few weeks of your exercise program, keep your
heart rate near the low end of your training zone.
The following guidelines will help you to plan your exer-
cise program. RememberÑthese are general guide-
lines only. For more detailed exercise information,
obtain a reputable book or consult your physician.
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed of the treadmill as
needed.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The prop-
er intensity level can be found by using your heart rate
as a guide. To find the proper heart rate for you, first
find your age at the top of the chart below (ages are
rounded off to the nearest ten years). Next, find the two
numbers below your age. The two numbers are your
Òtraining zone.Ó
WORKOUT GUIDELINES
Each workout should include the following three parts:
Warming Up
Start each workout with 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training Zone Exercise
After warming up, increase the intensity of your exer-
cise until your pulse is in your training zone for 20 to 60
minutes. (During the first few weeks of your exercise
program, do not keep your pulse in your training zone
for longer than 20 minutes.) Breathe regularly and
deeply as you exerciseÑnever hold your breath.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use stored
fat calories for energy. If your goal is to burn fat, adjust
the speed of the treadmill until your heart rate is near
the low end of your training zone. It may also be helpful
to set the speed control on the console to FAT BURN to
help you maintain the proper intensity level. (See page 8.)
Cool-down
Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
muscles and will help prevent post-exercise problems.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exercise
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown in the
drawings at the right. Move slowly as you stretchÑnever
bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for both legs. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
4
With one leg in front of the other, reach forward and place
your hands against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front leg, lean for-
ward and move your hips toward the wall. Hold for 15 counts,
then relax. Repeat 3 times for both legs. To cause further
stretching of the achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for both legs. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees out-
ward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. WLTL25581
R1299A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6*
7
8
9
1
1
1
1
1
1
1
1
1
1
12
4
2
1
6
1
1
1
1
1
1
1
1
1
10
1
1
4
4
4
4
2
2
2
1
2
1
1
2
12
1
1
1
2
1
Hood
Adhesive Clip
Motor Belt
Motor Pivot Nut
Pulley/Flywheel/Fan
Motor/Pulley/Flywheel/Fan
Motor
46
47
48
49*
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
#
1
1
1
1
1
1
6
1
1
2
7
1
2
1
1
2
2
2
1
2
2
2
2
1
2
4
1
1
1
1
1
8
1
4
1
2
1
1
0
8
8
2
1
1
Upright Plug
Console Cover
Battery Cover
Console Assembly
Speed Potentiometer
Speed Control Knob
Ground Screw/Belt Guide Screw
Wire Harness
Grommet
Base Leg
Belly Pan Fastener
Belly Pan
Upright Spacer
Motor Tension Washer
Left Foot Rail
Frame Pivot Nut
Belt Guide
Reed Switch
Clip Screw
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Reed Switch Clip
Hood Anchor Screw
Hood Anchor
Front Roller Bolt
Magnet
Platform Screw
Motor Tension Nut
Front Roller/Pulley
Motor Tension Bolt
Circuit Breaker
Power Cord Grommet
Frame
Power Cord
Controller
Motor Pivot Bolt
Screw
Choke
Electronics Bracket
Base Leg Bolt
Base Leg Washer
Base Leg Nut
Base Leg Pad
Base Leg Endcap
Wheel Bolt
Wire Clip
Right Foot Rail
Roller Guard
Frame Guide
Foot
Wheel Nut
Right Endcap
Rear Roller Adj. Bolt
Roller Adjustment Washer
Rear Roller
Ground Wire
Walking Platform
Walking Belt
Releaseable Tie
Handrail Bolt
Cable Tie Clamp
8Ó Cable Tie
Motor Star Washer
Front Roller Nut
Latch Bracket
Left Endcap
Wheel
Allen Wrench
Frame Pivot Bolt
Upright
Storage Latch
Latch Spring
Latch Screw/Guide Screw
Latch Spacer
Key Clip
Latch Decal
Frame Guide Screw
Console Base
Not Used
Handrail Washer
Handrail Nut
Foot Screw
14Ó White Wire, Male/Female
UserÕs Manual
#
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
¥ The MODEL NUMBER of the product (WLTL25581).
¥ The NAME of the product (WESLO CADENCE¨ 925 treadmill).
¥ The SERIAL NUMBER of the product (see the front cover of this manual).
¥ The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).
WESLO is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center, products used
for commercial or rental purposes, or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other con-
sequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 146717 H01496-C R1299A
Printed in USA © 1999 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|