¨
Model No. WLEL45070
Serial No.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if there
are missing or damaged parts,
please call direct to our toll-free
Customer Hot Line. The trained
technicians on our Customer Hot
Line will provide immediate
assistance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
Patent Pending
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
USERÕS MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the revolutionary
WESLO¨ ECLIPSE II elliptical exerciser. The
ECLIPSE II is an incredibly smooth exerciser that
moves your feet in a natural elliptical path, minimizing
the impact on your knees and ankles. And the unique
ECLIPSE II features adjustable resistance and moti-
vational electronics to help you get the most from your
exercise. Welcome to a whole new world of natural,
elliptical-motion exercise from WESLO.
tions, please call our Customer Service Department
toll-free at 1-800-999-3756, Monday through Friday, 6
a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is WLEL45070. The serial number can be
found on a decal attached to the ECLIPSE II (see the
front cover of this manual for the location of the decal).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
you use the ECLIPSE II. If you have additional ques-
Water Bottle Holder
(Bottle is not included)
Console
FRONT
Handlebar
Resistance Knob
Upright
Lock Pin
Pedal
Extension Tube
Side Shield
BACK
Pedal Leg
RIGHT SIDE
Base
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Use the chart below to identify the small parts used in
assembly. The number in parenthesis below each part
is the key number of the part, from the PART LIST on
page 14. The number after the dash indicates the
quantity needed for assembly.
#8 x 3/4" Tec Screw (42)Ñ1*
3/8" Nylon Locknut (54)Ñ4
1/2" Nylon Jam Nut (9)Ñ2
Handlebar Bushing (40)Ñ4*
Handlebar Spacer (46)Ñ2
5/8Ó Axle Cap (45)Ñ2
Crank Spacer (41)Ñ2
Pedal Leg Bushing (39)Ñ4*
Pedal Bolt (8)Ñ2
*Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has
been pre-attached.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Place all parts of the WESLO¨ ECLIPSE II in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included grease packet, a phillips screwdriver
wrenches
, two adjustable
, and a rubber mallet
.
1. Remove the #8 x 3/4Ó Tec Screw (42) from the Cable
Cover (53). While another person holds the Upright
(2) near the Base (1), carefully pull the Resistance
Cable (33) up through the Upright until there is no
slack between the Upright and the Base.
1
Slot
Next, insert the Extension Wire (49) into the Base (1)
until there is no slack between the Upright and the
Base.
33
53
42
Slide the Upright (2) onto the welded bolts on the
Base (1). Be careful to avoid pinching the
Extension Wire (49) and the Resistance Cable
(33). Tighten a 3/8Ó Nylon Locknut (54) onto each
welded bolt.
Insert the upper end of the Resistance Cable (33)
into the Upright (2) as shown. Insert the tab on the
Cable Cover (53) into the slot in the Upright. Attach
the Cable Cover to the Upright with the #8 x 3/4Ó Tec
Screw (42).
2
54
33
49
1
2. Identify the Left Handlebar (6) and the left Extension
Tube (5) (there are stickers on the Handlebars and
Extension Tubes for identification). Make sure that
there is a Tree Fastener (63) in the Extension Tube.
If there is not, insert a Tree Fastener as shown.
2a
6
2
6
37
37
Slide the Left Handlebar (6) onto the left Extension
Tube (5), being careful not to damage the Tree
Fastener (63). Align one of the three holes in the
Left Handlebar with the hole in the Extension Tube
and insert a Lock Pin (37) into the holes. Turn the
Lock Pin to the position shown in drawing 2a.
5
63
Repeat this step to attach the Right Handlebar to the
right Extension Tube (not shown).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Slide a Handlebar Spacer (46) onto the left axle on
the Upright (2). Make sure that the open side of the
Handlebar Spacer is facing the Upright. Next, make
sure that there are two Handlebar Bushings (40) in
the Left Handlebar (6). Slide the Left Handlebar onto
the left axle on the Upright. Tap a 5/8Ó Axle Cap (45)
onto the axle.
3
Repeat this step to attach the Right Handlebar (not
shown).
6
2
45
46
40
4. Make sure that there are two Pedal Leg Bushings
(39) in the left Pedal Leg (3). Apply a small amount
of grease to a Pedal Bolt (8). Insert the Pedal Bolt
into the left Pedal Leg and slide a Crank Spacer (41)
onto the Pedal Bolt. Tighten the Pedal Bolt into the
left Crank Arm (10), but do not overtighten it. You
should be able to turn the Crank Spacer with some
effort. Tighten a 1/2Ó Nylon Jam Nut (9) onto the
Pedal Bolt.
4
9
Repeat this step to attach the right Pedal Leg (not
shown).
10
3
41
39
8
5. The Console (52) requires two ÒAAÓ batteries (not
included). Alkaline batteries are recommended.
5
Batteries
To install batteries, first slide up the Battery Cover (60)
and carefully remove the battery clip from the Console
(52). Insert two batteries into the battery clip as shown.
Make sure that the negative ends of the batteries
(marked ÒÐÓ) are touching the springs in the
battery clip. Replace the battery clip and close the
Battery Cover.
60
Battery
Clip
52
6. Make sure that all parts of the ECLIPSE II are properly tightened. To protect the floor or carpet from
damage, place a mat under the ECLIPSE II.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE WESLO¨ ECLIPSE II
HOW TO EXERCISE ON THE WESLO¨ ECLIPSE II
HOW TO ADJUST THE HANDLEBARS
To mount the ECLIPSE II, hold the handlebars and
step onto the pedal that is in the lowest position.
Next, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:
The crank can turn in either direction; it is recom-
mended that you turn the crank in the direction
shown below; however, to give variety to your
exercise, you may choose to turn the crank in the
opposite direction.
To further add variety to your exercise, the handlebars
and extension tubes can be adjusted to any of three
positions.
Lock
Pin
Handlebar
Lock Pin
Holes
Extension
Tube
Pedal Leg
Pedal
Crank
Hold the right pedal leg. Remove the lock pin from the
right handlebar. Slide the extension tube up or down
until the hole in the extension tube is aligned with a
different hole in the handlebar. (Note: As you slide the
extension tube, be careful not to damage the tree
fastener [see assembly step 2].) Reinsert the lock pin
into the handlebar and the extension tube. Turn the
lock pin to the position shown in the inset drawing.
Next, adjust the position of the left handlebar and
extension tube. Make sure that the lock pins are in
the same holes in both handlebars. CAUTION: If the
lock pins are not turned to the position shown in
the inset drawing above, the lock pins could slip
out during use, resulting in injury to the user.
To dismount the ECLIPSE II, allow the pedals to
slowly come to a stop. CAUTION: The ECLIPSE II
does not have a freewheel; the pedals will contin-
ue to move until the flywheel stops. When the
pedals are stationary, step off the highest pedal first.
Then, step off the lowest pedal.
HOW TO ADJUST THE RESISTANCE OF THE
PEDALS
As you exercise,
you can adjust
the resistance of
the pedals with
the resistance
knob mounted on
the upright. To
increase the
Resistance Knob
resistance, turn
the knob
clockwise; to
decrease the
resistance, turn
the knob counterclockwise.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
Note: If there is a thin sheet of clear plastic
on the face of the console, remove it.
DESCRIPTION OF THE CONSOLE
The graphs on the left side of the console show how
the target pace will change during each program (see
the drawing above). Each graph is divided into ten
columns, and each column represents a two-minute
time period. The bars in each column show what the
target pace will be during that two-minute period. For
example, in the first column of the Interval graph, there
is one bar. This shows that during the first two minutes
of the Interval program, the target pace will be 40
repetitions (strides) per minute (see the scale at the
right end of the graph). In the second column, there
are five bars. This shows that during the second two-
minute period, the target pace will be 80 strides per
minute. Each pacer program is twenty minutes long.
The innovative console offers a manual mode and
three pacer programs. The pacer programs are
designed to help you achieve your exercise goals by
pacing your exercise. The programs include a stamina-
building Interval program, an Aerobic program, and a
Fat Burn program. The console also features six moni-
tor modes that provide continuous exercise feedback.
HOW THE PACER PROGRAMS OPERATE
When you use a
pacer program,
two columns of
bars will appear in
the display. The
left column will
show a target
DESCRIPTION OF THE MONITOR MODES
The six monitor modes provide continuous exercise
feedback. The modes are described below.
pace; the right
column will show
your actual pace.
Target Pace Actual Pace
¥ Reps per minute (REPS/MIN)ÑThis mode shows
your pace, in repetitions (strides) per minute.
The target pace will change periodically during the
program; as the target pace changes, simply adjust
your pace to keep both columns at the same height.
Important: The target pace is a goal pace. Your
actual pace may be slower than the target pace,
especially during the first few months of your
exercise program. Be sure to exercise at a pace
that is comfortable for you.
¥ TimeÑIf you select one of the three pacer programs,
this mode will count down the time remaining in the
program. If you select the manual mode, this mode
will count up the length of time you have exercised.
Note: If you stop exercising for ten seconds or
longer, the time mode will pause.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
¥ DistanceÑThis mode shows the total number of
repetitions (strides) you have completed, up to 999.
The display will then reset to zero and continue
counting.
Begin your workout
3
If you selected
the manual
mode, go to step
4. If you selected
one of the pacer
programs, two
columns of bars
will appear in the
display. The left
column will show
one bar, showing that the target pace is 40 strides
per minute. The right column will show your actual
pace. Adjust your pace until only one bar appears
in the right column. As the program progresses,
the target pace will change periodically; as the
target pace changes, adjust your pace to keep
both columns at the same height. Important: The
target pace is a goal pace. Your actual pace
may be slower than the target pace, especially
during the first few months of your exercise
program. Be sure to exercise at a pace that is
comfortable for you.
¥ Fat calories (FAT CALS)ÑThis mode shows the
approximate number of fat calories you have
burned. (See BURNING FAT on page 12 for an
explanation of fat calories.)
Target Pace Actual Pace
¥ Calories (CALS)ÑThis mode shows the approxi-
mate number of calories you have burned. (This
number includes both fat calories and carbohydrate
calories.)
¥ ScanÑThis mode displays the calories, fat calories,
reps per minute, time, and distance modes, for five
seconds each, in a repeating cycle.
STEP-BY-STEP CONSOLE OPERATION
Before the console can be operated, two ÒAAÓ bat-
teries must be installed. (See assembly step 5 on
page 6 for installation instructions.) Follow the steps
below to operate the console.
Follow your progress with the monitor modes
4
Turn on the power
1
When the power
is turned on, the
Mode Indicators
To turn on the
power, press the
scan mode will
automatically be
selected. One
mode indicator
will show that the
scan mode is
selected, and a
flashing mode
indicator will show which mode is currently
displayed. Note: If you select a different mode, you
can select the scan mode again by repeatedly
pressing the mode button.
on/reset button
or simply begin
exercising on the
ECLIPSE II.
When the power is turned on, the entire display
will appear for two seconds. The console will then
be ready for use. Note: If batteries were just
installed, the power will already be on.
Select one of the three pacer programs or the
manual mode
2
To select one of
the pacer
programs,
repeatedly press
the program but-
ton. The program
If desired, you can select the reps per minute,
time, distance, fat calories, or calories mode for
full-time display. To select one of these modes,
repeatedly press the mode button. The mode
indicators will show which mode is selected.
(Make sure that the scan mode is not selected.)
Program Indicator
indicator will
show which
program you
have selected. To
If desired, the display can be reset by pressing
the on/reset button.
select the manual mode, press the program
button until the program indicator disappears.
The programs will be selected in the following
order: program 1 (Interval), program 2 (Aerobic),
program 3 (Fat Burn), and the manual mode.
Turn off the power
5
To turn off the power, simply wait for about
four minutes. If the pedals are not moved and
the console buttons are not pressed for four
minutes, the power will turn off automatically.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CONSOLE TROUBLE-SHOOTING
Next, locate the
Reed Switch (48).
Turn the Pulley
(19) until the
Magnet (55) is
aligned with the
Reed Switch.
If the console does not function properly, the batteries
should be replaced. To replace the batteries, see
assembly step 5 on page 6. In addition, make sure
that the extension wire is plugged into the console.
(See assembly step 1 on page 5.)
55
51
Loosen, but do
not remove, the
#10 x 1/2Ó Tec
Screw (51). Slide
the Reed Switch
slightly closer to or farther away from the Magnet.
Make sure that the Magnet will not hit the Reed
Switch. Retighten the Tec Screw. Turn the Pulley for a
moment. Repeat until the console displays correct
feedback. When the Reed Switch is correctly adjusted,
reattach the side shield and the crank arms.
48
HOW TO ADJUST THE REED SWITCH
19
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, the Side Shield (27) must first be removed.
Remove the 5/16Ó x 3/4Ó Tap Screw (18) from the left
Crank Arm (10). Slide the left Crank Arm off the Crank
Shaft (11). Remove the right Crank Arm (not shown) in
the same way.
HOW TO ADJUST THE RESISTANCE STRAP
Top
27
If the pedals do not have enough resistance, even
when the resistance knob is turned to the maximum
setting, the Resistance Strap (31) may need to be
adjusted. To adjust the Resistance Strap, the side
shield must first be removed. Refer to the instructions
at the left to remove the side shield.
Back
10
11
18
Turn the resistance knob to the lowest setting. (See
HOW TO ADJUST THE RESISTANCE OF THE
PEDALS on page 7.) Grip the end of the Resistance
Strap (31) and
pull it away from
the rest of the
Strap. Next, pull
the end of the
Strap up to
42
Remove the three #8 x 3/4Ó Tec Screws (42) from
each side of the Side Shield (27).
31
remove any
Hold the Side Shield (27) near the back and pull it
apart slightly until the Side Shield can be lifted off the
ends of the Crank Shaft (11). Remove the Side Shield.
Do not pull the Side Shield apart at the top or the
seam may be broken.
slack. Then press
the end of the
Strap against the
rest of the Strap
as shown. Turn
the pulley for a
moment to make sure that there is not too much
resistance. When the Resistance Strap is properly
adjusted, reattach the side shield and the crank arms.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ADJUST THE DRIVE BELT
If the Drive Belt (32) slips as you exercise on the
ECLIPSE II, the Drive Belt should be adjusted. To
adjust the Drive Belt, the side shield must first be
removed. Refer to the instructions on page 10 and
remove the side shield.
Next, loosen the
two 3/8Ó Nylon
Jam Nuts (23)
(there is one on
each side of the
Flywheel [20]).
To tighten the
Drive Belt (32),
turn the two
20
32
26
23
1/4Ó Nylon
Locknuts (26)
clockwise; to
loosen the Drive
Belt, turn the Nylon Locknuts counterclockwise. Make
sure that the Flywheel is straight and retighten the 3/8Ó
Nylon Jam Nuts (23). When the Drive Belt is properly
adjusted, reattach the side shield and the crank arms.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition and
adequate rest are essential for successful results.
Burning Fat
To burn fat effectively, you must exercise at the proper
intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easi-
ly accessible carbohydrate calories for energy. Only
after the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn
fat, it may be helpful to use the Fat Burn program to
help you to reach your goal. (See pages 11 and 12.)
WARNING: Before beginning this or any exercise
program, consult your physician. This is especial-
ly important for individuals over the age of 35 or
individuals with pre-existing health problems.
WHY EXERCISE?
Exercise has proven essential for good health and
well-being. Participation in a well-rounded exercise
program helps to develop a stronger and more effi-
cient heart, improved respiratory function, increased
stamina, better weight management, increased ability
to handle stress, and greater self-esteem.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For effective aerobic
exercise, it may be helpful to use the Aerobic program
to help you to reach your goal. (See pages 11 and 12.)
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
To develop greater stamina, you may choose the
Interval program to help you to reach your goal. (See
heart rate as a guide. For effective exercise, your heart pages 11 and 12.)
rate should be maintained at a level between 70% and
85% of your maximum heart rate as you exercise. This
is known as your training zone. You can find your train-
ing zone in the table below. Training zones are listed
according to age and physical condition.
HOW TO MEASURE YOUR HEART RATE
To measure your heart rate, stop exercising and place
two fingers on your wrist as shown. Take a six-second
heartbeat count,
and multiply the
result by ten to
find your heart
rate. (A six-
second count is
used because
your heart rate
drops quickly
when you stop
exercising.) If
your heart rate
is too high, decrease the intensity of your exercise. If
your heart rate is too low, increase the intensity of
your exercise.
TRAINING ZONE (BEATS/MIN.)
AGE UNCONDITIONED CONDITIONED
20
25
30
35
40
45
50
55
60
65
70
75
80
138Ð167
136Ð166
135Ð164
134Ð162
132Ð161
131Ð159
129Ð156
127Ð155
126Ð153
125Ð151
123Ð150
122Ð147
120Ð146
133Ð162
132Ð160
130Ð158
129Ð156
127Ð155
125Ð153
124Ð150
122Ð149
121Ð147
119Ð145
118Ð144
117Ð142
115Ð140
WORKOUT GUIDELINES
A proper workout includes the following parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases the
body temperature, heart rate, and circulation in prepa-
ration for exercise.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
A cardiovascular exercise period, including 20 to
30 minutes of exercise with your heart rate in your
training zone.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Find the best time of day for your
workouts, and then stick with it.
A cool-down, with 5 to 10 minutes of stretching.
Thorough stretching helps to offset problems caused
when you stop exercising suddenly. Stretching after
exercise is also very effective for increasing flexibility.
SUGGESTED STRETCHES
1
The correct form for several basic stretches is shown at the
right. Move slowly as you stretchÑnever bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place
your hands against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front leg, lean for-
ward and move your hips toward the wall. Hold for 15 counts,
then relax. Repeat 3 times for each leg. To cause further
stretching of the achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees out-
ward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. WLEL45070
R1197A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
2
2
2
1
1
2
2
2
1
2
2
1
1
1
1
2
1
1
1
2
2
2
2
2
1
2
2
1
1
1
1
1
2
Base
Upright
Pedal Leg
Pedal Bracket
Extension Tube
Left Handlebar
Right Handlebar
Pedal Bolt
1/2Ó Nylon Jam Nut
Crank Arm
Crank Shaft
Crank Bearing
Bearing Cup
Keyed Washer
Slotted Crank Nut
Tri-notch Crank Nut
Crank Nut
5/16Ó x 3/4Ó Tap Screw
12Ó Pulley
Flywheel w/Hub
Flywheel Axle
3/8Ó Flat Washer
3/8Ó Nylon Jam Nut
1/4Ó Eyebolt
Adjustment Bracket
1/4Ó Nylon Locknut
Side Shield
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
#
2
2
2
8
4
2
27
2
1
2
2
4
1
1
1
1
1
1
4
1
1
4
1
1
1
2
2
2*
1
1
Extension Tube Endcap
Lock Pin
Crank Washer
Pedal Leg Bushing
Handlebar Bushing
Crank Spacer
#8 x 3/4Ó Tec Screw
3/4Ó Axle Cap
Cable Bracket
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
5/8Ó Axle Cap
Handlebar Spacer
Stabilizer Endcap
Reed Switch/Sensor Wire
Extension Wire
Reed Switch Clamp
#10 x 1/2Ó Tec Screw
Console
Cable Cover
3/8Ó Nylon Locknut
Magnet
Clamp Bolt
1/4Ó Flat Washer
1/4Ó Nylon Locknut
Resistance Strap Hook
Battery Cover
Flywheel Bearing
Pedal Leg Spacer
Tree Fastener
UserÕs Manual
Grease Packet
Bearing Washer
Pedal Cover
Resistance Strap Bracket
Resistance Strap
Drive Belt
Resistance Cable w/Spring
Resistance Knob
Handgrip
#
* Extra Tree Fasteners may be included
# This part is not illustrated
Specifications are subject to change without notice. See the back cover of this manual for information about
ordering replacement parts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWINGÑModel No. WLEL45070
R1197A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be
prepared to give the following information when calling:
¥ The MODEL NUMBER of the product (WLEL45070).
¥ The NAME of the product (WESLO¨ ECLIPSE II elliptical exerciser).
¥ The SERIAL NUMBER of the product (see the front cover of this manual).
¥ The KEY NUMBER and DESCRIPTION of the part(s) from page 14 of this manual.
WESLO¨ is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICONÕs obligation under this warranty is lim-
ited to replacing or repairing, at ICONÕs option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service cen-
ters with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase.
All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to
a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by an ICON authorized service center, to products used for commercial or rental pur-
poses, or to products used as store display models. No other warranty beyond that specifically set forth
above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON Health & Fitness, Inc. 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 142265 G03916-C R1197A
Printed in USA © 1997 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|