Wells Water Dispenser WM TR II User Manual

707

OPERATION MANUAL

WATER-MAX II™

WM-TR II™

HOT WATER

DISPENSER

Includes

INSTALLATION

USE & CARE

IMPORTANT: DO NOT DISCARD THIS MANUAL

This manual is considered to be part of the appliance and is to be given to the OWNER or

MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of

this appliance. Additional manuals are available from your WELLS DEALER.

THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR

INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any

questions

concerning installation,

PRINTED IN UNITED STATES OF AMERICA

p/n 306692 Rev. A ECN-13060

M707 060418 cps

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

WARRANTY

SPECIFICATIONS

FEATURES & OPERATING CONTROLS

PRECAUTIONS & GENERAL INFORMATION

AGENCY LISTING INFORMATION

INSTALLATION

OPERATION

CLEANING INSTRUCTIONS

TROUBLESHOOTING SUGGESTIONS

PARTS & SERVICE

CUSTOMER SERVICE DATA

INTRODUCTION

Thank you for purchasing this Wells Manufacturing Co. appliance.

Proper installation, professional operation and consistent maintenance of this appliance will ensure that it

gives you the very best performance and a long, economical service life.

This manual contains the information needed to properly install this appliance, and to use and care for the

appliance in a manner which will ensure its optimum performance.

SPECIFICATIONS

Electrical:

Plumbing:

208 Volts, Single Phase 30 Amps

240 Volts, Single Phase 27 Amps

NOTE: Requires a dedicated 40 Amp circuit

Water Inlet: 1/4” Male Flare Fitting

Supply: 1/4” Female Flare supplied by a 1/4” O.D. or larger water supply line

NOTE: If water supply run from main supply line to Water-Max™ exceeds 12 feet,

a 3/8” O.D. or larger water supply line is required.

IMPORTANT: This dispenser must be installed in compliance with all applicable

federal, state and local codes and ordinances.

Dimensions: Height:

Width:

32-5/8”

13-1/8” (with satellite installed)

20-3/4” (without satellite)

Depth:

24” (with satellite installed)

Weight:

55 lbs. (heater assembly only, dry) 20 lbs. (satellite only, dry)

146 lbs. (operating configuration - filled, with satellite installed & filled)

62 lbs. (satellite only, filled)

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES & OPERATING CONTROLS

HEAT (AMBER)

REFILL (AMBER)

POWER (GREEN)

HEATER SWITCH

DELIME

QUICK-DISCONNECT

see page 11

FLOW

NOZZLE

SATELLITE

POSITION

SENSOR

DELIME

SOLUTION

BOTTLE

SATELLITE

see page 3

SATELLITE

CONNECTOR

POWER

INLET

NAMEPLATE

WELLS

DRAIN VALVE

MOUNTING

BRACKET

WATER

INLET

FITTING

ADJUSTABLE

LEG

DRAIN

FITTING

HEATER

DRAIN

VALVE

DRAIN HOSE

W/ CLAMP

Fig. 1 Features & Operating Controls - Water Max II™ Hot Water Dispenser

ITEM DESCRIPTION NOTES

HEATER SWITCH

POWER LIGHT

REFILL LIGHT

Controls power to water heater, satellite heater and satellite fill

Indicates main power available

Indicates satellite is being refilled from the main tank

Indicates heater element is energized and water is heating

Satellite fill device

HEAT LIGHT

FLOW NOZZLE

SATELLITE SWITCH

Senses if satellite is in position

SATELLITE CONNECTOR Electrical connector for satellite heater and fill

NAMEPLATE

Lists manufacturer, model & serial number, voltage & wattage.

Supports unit off of counter and allows unit to be leveled

Non-skid foot resists movement of unit on counter

ADJUSTABLE LEG

10 POWER INLET

Electrical power fitting connects here

Inlet water connects here

11 INLET FITTING

12 DRAIN FITTING

13 MOUNTING BRACKET

Drain assembly connects here

Stabilizes drain valve, provides place to store drain hose

14 HEATER DRAIN VALVE Allows main water heater tank to be drained for service

15 DRAIN HOSE w/CLAMP Control and direct drain stream

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES & OPERATING CONTROLS (continued)

SATELLITE ASSEMBLY

WATER LEVEL

SENSOR

COVER HOLDER

CLIPS

COVER

WELLS

HANDLE

FAUCET

GUARD

NAMEPLATE

DISPENSE

FAUCET

SATELLITE

CONNECTOR

BACK VIEW

FRONT VIEW

Fig. 2 Features & Operating Controls - Water Max II™ 5 Gallon Satellite

ITEM DESCRIPTION

NOTES

S1 COVER

Forms fill funnel, allows access to tank for service

S2 COVER HOLDING CLIPS Retains cover in place

S3 WATER LEVEL SENSOR Maintains water level in tank

S4 DISPENSE FAUCET

S5 FAUCET GUARD

S6 HANDLE

Dispense hot water here

Helps to protect faucet from damage

Used to install/remove satellite on heater unit

S7 SATELLITE CONNECTOR Electrical connector for satellite heater and fill

S8 NAMEPLATE Lists manufacturer, model & serial number, voltage & wattage.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS AND GENERAL INFORMATION

Water-Max II™ hot water dispenser is intended for use in

commercial establishments only.

WARNING:

Electric

Shock hazard

This dispenser is designed to dispense hot water used in the

preparation of food for human consumption. No other use is

recommended or authorized by the manufacturer or its agents.

All servicing requiring

access to non-insulated

electrical components

must be performed by a

factory authorized

Operators of this appliance must be familiar with the appliance use,

limitations and associated restrictions.

Operating instructions, warnings and labels must be read and

understood by all persons using or installing this appliance.

technician.

DO NOT open any access

panel which requires the

use of tools. Failure to

follow this warning can

result in severe electrical

shock.

Cleanliness of this dispenser is essential to good sanitation. Read and

follow all included cleaning instructions and schedules to ensure the

safety of the food product.

Disconnect this appliance from electrical power before performing any

maintenance or servicing.

DO NOT submerge the dispenser or satellite in water. Do not splash

or pour water on, in or over any controls, control panel or wiring.

CAUTION:

Risk of

Damage

The technical content of this manual, including any wiring diagrams,

schematics, parts breakdown illustrations and/or adjustment

procedures, is intended for use by qualified technical personnel.

DO NOT connect or

energize this appliance

until all installation

Any procedure which requires the use of tools must be performed by a

qualified technician.

instructions are read and

followed. Damage to the

appliance will result if

these instructions are not

followed.

This manual is considered to be a permanent part of the appliance.

This manual and all supplied instructions, diagrams, schematics, parts

breakdown illustrations, notices and labels must remain with the

appliance if it is sold or moved to another location.

This appliance is made in the USA. Unless otherwise noted, this

appliance has American sizes on all hardware.

AGENCY LISTING INFORMATION

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

NOTE: DO NOT discard

UNPACKING & INSPECTION

the carton or other packing

materials until you have

inspected the appliance for

hidden damage and tested it

for proper operation.

Refer to SHIPPING DAMAGE

CLAIM PROCEDURE on the

inside front cover of this

manual.

Carefully remove the appliance from the carton. Remove all protective

plastic film, packing materials and accessories from the appliance

before connecting electrical power or otherwise performing any

installation procedure.

Carefully read all instructions in this manual and the Installation

Instruction Sheet packed with the appliance before starting any

installation.

Read all instructions in this manual carefully before starting installation

of this dispenser. READ AND UNDERSTAND ALL LABELS AND

DIAGRAMS ATTACHED TO THE DISPENSER.

WARNING:

Risk of

personal injury

Carefully account for all components and accessories before discarding

packing materials.

1 ea.

4 ea.

1 ea.

WATER-MAX II™ HOT WATER DISPENSER

ADJUSTABLE LEGS

DRAIN ASSEMBLY w/ MOUNTING BRACKET

SATELLITE TANK ASSEMBLY with LID

PLASTIC SOLUTION BOTTLE with

QUICK DISCONNECT FITTING

Installation procedures must

be performed by a qualified

technician with full knowledge

of all applicable electrical and

plumbing codes. Failure can

result in personal injury and

property damage.

1 ea.

LITERATURE PACKAGE

Store these components in a convenient place for later use:

IMPORTANT: A one gallon

pitcher of water will weigh

about 8-1/2 pounds and will be

VERY HOT.

SETUP

Verify that this dispenser installation is in compliance with the

specifications listed in this manual and with local code requirements.

THIS IS THE RESPONSIBILITY OF THE INSTALLER.

When connecting drain

assembly, be sure to connect

to the DRAIN FITTING.

Recommended height of the faucet is 38” to 42” from the floor.

However, the actual installed height may vary with the requirements of

the individual store.

(FRONT)

The counter at the installation location must be level, provide a clear

space at least 17-1/2”” deep and must be structurally capable of safely

supporting the 150 pound weight of the Water-Max II™ and satellite

when filled with water.

MOUNTING

BRACKET

DRAIN

ASSEMBLY

Position DRAIN VALVE MOUNTING BRACKET. Install LEGS, one on

each bottom corner. Front legs retain mounting bracket. Make certain

all four legs have the NON-SKID FEET installed.

ELECTRIC

SERVICE

INLET

Connect DRAIN HOSE and CLAMP to DRAIN ASSEMBLY. Feed hose

through MOUNTING BRACKET from the rear, then connect assembly

to DRAIN FITTING on bottom of unit, left side near the rear of the unit.

WATER INLET

FITTING

Set Water-Max II™ upright on the counter.

With the dispenser in its final installed location, adjust for level with the

adjustable legs. With a spirit level, check and adjust the dispenser for

level front-to-rear and side-to-side.

DRAIN

FITTING

(REAR)

BOTTOM VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (continued)

CAUTION:

PLUMBING LINE CONNECTION

RISK OF DAMAGE

If power has been run to the dispenser, verify that the circuit breaker is

turned OFF, and that the POWER SWITCH is in the OFF [O] position.

DO NOT connect or energize

this appliance until all Installation

Instructions are read and followed.

Damage to the dispenser will

occur if these instructions are

not followed.

Water-Max II™ must be connected to a potable water supply. Connect

to a cold water line only. Connecting to a hot water line will damage the

inlet water valve.

NOTICE:

WATER PIPE CONNECTIONS AND FIXTURES DIRECTLY

CONNECTED TO A POTABLE WATER SUPPLY SHALL BE SIZED,

INSTALLED AND MAINTAINED ACCORDING TO FEDERAL, STATE,

AND LOCAL ORDINANCES.

IMPORTANT: Water supply

MUST be a minimum of 1/4”

line, and MUST be capable of

supplying 25 p.s.i. AT ALL

TIMES during the operation of

the dispenser.

Minimum 1/4” copper or flex tubing supply line (3/8” minimum if run

from main supply exceeds 12 feet) with 1/4” female flare fitting.

Minimum 25 psi / maximum 75 psi water pressure at full flow.

The installation of a SHUTOFF VALVE (must be provided by plumbing

installer) on the incoming water line is required. A 1/4 turn ball valve is

recommended to minimize restricting the water flow during operation.

Installation of a PRESSURE REGULATOR and WATER HAMMER

ARRESTOR (to be provided by plumbing installer) on the incoming

water line is recommended.

Clean the incoming waterline: Run water through the line into a sink or

bucket to flush any foreign particles or debris from the waterline.

Assemble incoming water line to the inlet fitting. Turn on water supply

valve and check for leaks.

If a pressure regulator is installed, adjust pressure to 40 p.s.i.

Fig. 3 1/4 Turn Ball Valve

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (continued)

ELECTRICAL INSTALLATION

CAUTION:

SHOCK HAZARD

NOTICE:

A DEDICATED CIRCUIT OF AT LEAST 40 AMPS IS REQUIRED.

Removal of any exterior panel

will result in exposed electrical

circuits. Electrical connection

must be performed by a

qualified technician only.

Use care whenever working

around exposed electrical

circuits.

WIRING AND CONNECTIONS MUST BE INSTALLED AND

MAINTAINED IN COMPLIANCE WITH

FEDERAL, STATE, AND LOCAL ORDINANCES.

The dispenser is factory configured for either 208 volts or 240 volts.

The voltage configuration is NOT field convertible.

DO NOT connect unit to electric power until water supply is connected

and turned on.

IMPORTANT:

Contact a licensed electrician

co connect electric power to

the dispenser.

Be sure HEATER SWITCH is OFF (O) before connecting unit to electric

power.

IMPORTANT:

Damage due to being

connected to the wrong

voltage or phase is NOT

covered by warranty.

IMPORTANT:

Supply voltage must

correspond to the nameplate

voltage of the unit. Connection

to the wrong voltage can result

in equipment damage or

reduced performance.

Such damage is not covered

by warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (continued)

CAUTION:

Hot Surface

INSTALLATION START-UP AND CHECKOUT

Before turning on power or water to Water-Max II™, verify:

Exposed surfaces can be hot

to the touch and may cause

burns.

a. Unit is level, with all legs touching the counter

b. Water and electrical connections properly made

c. HEATER SWITCH is OFF ( O )

d. Removable SATELLITE is NOT installed on Water-Max II™ at this

time

CAUTION

Burn Hazard

Only after steps a. through d. are satisfactorily completed:

Water in Water-Max II™ is

EXTREMELY HOT!

e. Turn on water supply valve to Water-Max II™.

f. Turn on electric power to unit. Green POWER light must be off.

Water will automatically start filling the internal tank.

g. WAIT at least 4 minutes. The internal tank fill solenoid must shut

off before proceeding.

h. Once internal tank fill solenoid shuts off, verify water in tank by

opening DRAIN VALVE momentarily. Water must be present at

drain valve.

CAUTION

SCALDING

HAZARD

Place satellite tank on

dispenser as soon as the

main tank is at temperature

(i.e. READY light lit).

Failure to do so may result

in steam splattering when

satellite is installed and

satellite filling begins.

Once satisfied that the heater tank is filled:

i. Press the HEATER SWITCH to ON ( I ). Green POWER light will

glow. Water in the heater tank will begin heating and the amber

HEAT light will glow.

Approximately 15 - 20 minutes after energizing the heater, HEAT

light will turn off, indicating water in the tank has reached the

setpoint temperature.

j. Press the HEATER SWITCH to OFF ( O )

Be sure the COVER is properly installed on the SATELLITE.

Install SATELLITE on Water-Max II™ shelf.

IMPORTANT:

DO NOT energize the

Press the HEATER SWITCH to ON ( I ). Amber REFILL light will

glow and hot water will begin filling the satellite after 15 - 20

seconds.

HEATER SWITCH until the

heater tank is filled. Damage

to the heating element will

occur. Such damage is NOT

covered under warranty.

k. Satellite tank will fill completely within 30 minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

Water-Max II™ is used to dispense hot water for food preparation. The

SATELLITE TANK stores five gallons of hot water for immediate use.

WARNING:

BURN HAZARD

INSTALLING OR REMOVING SATELLITE TANK

Water-Max™ is designed to

operate with a matching 5 gal.

satellite water tank only.

Do not hold anything other

than the matching satellite

under the dispensing nozzle.

Splashing hot water will cause

serious burns.

Drain all water from SATELLITE before attempting to remove from unit.

Press the HEATER SWITCH to OFF ( O )

Be sure the COVER is properly installed on the SATELLITE

Install or remove SATELLITE on Water-Max II™ shelf by lifting up on

satellite faucet guard.

When installing the tank, make sure that the tank is properly positioned,

that the connector is seated, and that the dispensing nozzle lowered

into position in the satellite cover.

Press the HEATER SWITCH to ON ( I ). Amber REFILL light will glow

and hot water will begin filling the satellite after 15 - 20 seconds.

Place an appropriate container under the faucet. Being careful not to

overflow the container, pull the faucet handle to dispense hot water.

GENERAL GUIDELINES

NEVER hold or place

anything, other than the proper

satellite, under the dispense

nozzle. Draw water only from

the hot water faucet of the

satellite water tank.

DISPENSE

NOZZLE

OFF

NEVER attempt to remove or

carry a satellite while full of

water.

HOT WATER

FAUCET

NEVER attempt to operate

Water-Max II™ without the

cover properly installed on the

satellite

CAUTION:

Hot Surface

Fig. 5 Water-Max™ Operation

Exposed surfaces can be hot

to the touch and may cause

burns.

To Keep Water in Satellite Hot

Leave the heater switch ON. The satellite has an internal heater to

maintain the tank temperature, and will remain ready to dispense hot

water.

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEANING INSTRUCTIONS

DAILY CLEANING

CAUTION:

PRECAUTIONS: Press HEATER SWITCH to OFF ( O ).

Drain all water from SATELLITE.

BURN HAZARD

Remove satellite from Water-Max II™.

Water in satellite is extremely

hot. Use care when draining.

FREQUENCY:

TOOLS:

Minimum - Daily, or as required

Soft Cloth, Soft Bristle Brush

CAUTION:

HOT SURFACES

TANK LID

Exposed surfaces can be hot

to the touch and may cause

burns.

CAUTION:

EQUIPMENT

DAMAGE

HANDLE &

BONNET

TANK

FAUCET

DO NOT SUBMERGE

SATELLITE IN WATER!

FAUCET

BODY

IMPORTANT:

DO NOT use bleach,

abrasive cleansers or

cleansers containing

chlorides.

SCREEN

Wipe down the exterior of the Water-MaxII™ with a soft damp cloth.

Use a soft bristle brush to remove any calcium or lime build-up on the

end of the dispensing nozzle. Wipe dispensing nozzle clean with a soft

damp cloth.

Remove SATELLITE COVER.

Wipe satellite FAUCET, and interior and exterior of tank with a soft

damp cloth. DO NOT SUBMERGE SATELLITE IN WATER!

Fill satellite with cool, clean water. Check operation of faucet.

If the faucet leaks:

Drain tank

Disassemble faucet by unscrewing bonnet from faucet body.

Clean or repair faucet as necessary.

Reassemble bonnet on faucet body.

Reinstall SATELLITE COVER.

Drain any remaining water from satellite, re-install on Water-Max II™.

Press HEATER SWITCH to ON ( I ) and test for proper operation.

Procedure is complete.

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEANING INSTRUCTIONS (continued)

FIRST AID

PERIODIC CLEANING - Delime Internal Heating Tank

PRECAUTIONS: Water in main tank is EXTREMELY HOT

(around 200ºF)

EYES: In case of contact,

immediately flush with warm

water for 15 minutes.

Contact a physician if

irritation persists.

FREQUENCY: Weekly

TOOLS:

Wells Deliming Solution Bottle (p/n 85377)

Plastic Scouring Pad

Clean Cloth or Sponge

SKIN: Wash with soap and

water.

Kay Orange Neutralizer and Delimer (Kay p/n 55905)

Contact a physician if

irritation persists.

Begin with the HEATER SWITCH ON, MAIN TANK full and at

temperature (i.e. HEAT light not lit), and with SATELLITE full of hot

water.

INGESTION: If swallowed,

drink plenty of water and

contact a physician

Disconnect water to unit, or turn off main water supply valve.

KAY CHEMICAL CO.

EMERGENCY PHONE

(800) 304-0824

Pour contents (1 oz.) of Neutralizer and Delimer packet into the plastic

solution bottle.

Fill the rest of the bottle with hot water from the satellite faucet.

Attach quick-disconnect fitting cap on bottle.

INGREDIENTS

Organic acids. Non-toxic

when used as directed.

Invert the solution bottle over the quick-disconnect fitting on the

dispenser. Insert the bottle until it locks into place.

For description of features

refer to page 2.

Squeeze solution bottle until all solution is forced into dispenser.

Press release on quick-disconnect. Remove solution bottle. Wipe clean

the quick-disconnect fittings. Rinse solution bottle with clean water.

Press TANK HEATER SWITCH to OFF [O]. Allow cleaning solution to

soak in main tank for 30 minutes.

CONTINUED ON PAGE 12

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEANING INSTRUCTIONS (continued

CONTINUED FROM PAGE 11

CAUTION

Burn Hazard

After 30 minutes, flush solution from main tank (HEATER SWITCH OFF):

Water in Water-Max II™ is

EXTREMELY HOT! Wear

appropriate heat protective

clothing when draining water

from unit.

Insert drain hose into a suitable container. Open drain hose clamp and

drain valve. Allow all solution to drain.

Close drain valve. Reconnect main water supply and allow main tank to

fill (approximately 4 minutes).

IMPORTANT:

Never drain internal tank with

HEATER SWITCH ON.

Tank heating element will be

damaged if allowed to

operate without water.

After tank is filled, disconnect main water supply and drain tank again.

Flush tank in this manner at least two (2) times.

After flushing tank:

Be sure drain valve and drain hose clamp are closed. Stow drain hose

and reconnect main water supply. After tank is filled (approximately 4

minutes), press HEATER SWITCH to ON ( I ). After a short delay, main

tank will begin filling. When water reaches proper temperature, satellite

will begin filling.

For description of features

refer to page 2.

Procedure is complete

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEANING INSTRUCTIONS (continued)

FIRST AID

PERIODIC CLEANING - Satellite Tank

PRECAUTIONS: Water in satellite is EXTREMELY HOT

(around 200ºF)

EYES: In case of contact,

immediately flush with warm

water for 15 minutes.

Contact a physician if

irritation persists.

Satellite full of water is HEAVY (62 lbs.)

Drain water from SATELLITE before moving.

FREQUENCY: Weekly

TOOLS:

Plastic Scouring Pad

Clean Cloth or Sponge

Kay Orange Neutralizer and Delimer (Kay p/n 55905)

SKIN: Wash with soap and

water.

Contact a physician if

irritation persists.

Press HEATER SWITCH to OFF [ O ].

Drain SATELLITE and remove from Water-Max II™.

Remove SATELLITE COVER.

INGESTION: If swallowed,

drink plenty of water and

contact a physician

Pour contents of one package of Neutralizer and Delimer into

SATELLITE. Fill with hot tap water/

KAY CHEMICAL CO.

EMERGENCY PHONE

(800) 304-0824

Allow solution to soak at least 30 minutes.

After soak period:

Carefully drain SATELLITE. Properly dispose of used deliming solution.

INGREDIENTS

Organic acids. Non-toxic

when used as directed.

WATER LEVEL PROBE is located in the tank, in the back right corner

near the top. Using a PLASTIC SCRUB PAD, clean all scale and lime

from the water level probe. Using the scrub pad, clean all scale and

lime deposits from the lip of the tank opening and from the inside of the

tank.

For description of features

refer to page 3.

Rinse tank thoroughly at least twice. Pour all rinse water into a sink or

appropriate container for disposal.

Reinstall SATELLITE COVER on SATELLITE. Reinstall SATELLITE on

Water-Max II™. Make sure tank connector is fully seated.

Press HEATER SWITCH to ON [ I ]. After a short delay, main tank will

begin filling. When water reaches proper temperature, satellite will

begin filling.

Procedure is complete

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING SUGGESTIONS

SYMPTOM

POSSIBLE CAUSE

SUGGESTED REMEDY

Power light not lit

Circuit breaker off or tripped

Reset circuit breaker

Satellite not properly positioned

on shelf

Set satellite in proper position

Verify water supply is fully on

Satellite does not fill

Inlet solenoid strainer plugged -

clean strainer

Low water in main tank

Internal damage - contact

Authorized Wells Service Agency

Contact Authorized Wells Service

Agency

Satellite suffers excessive fill time Improper internal adjustments

Satellite not properly positioned

on shelf

Set satellite in proper position -

verify connector securely seated

Dispensed water not hot enough

Water temp thermostat not set

Contact Authorized Wells Service

Agency

Dispense thermostat set too low

Tripped circuit breaker

Main tank does not heat

Contact Authorized Wells Service

Agency

Internal damage

There are no user serviceable components in the appliance. In all cases of damage or component

malfunction, contact your Authorized Wells Service Agency for repairs.

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS & SERVICE

DESCRIPTION

SERVICE

PART NO.

IMPORTANT: Use only

factory authorized service

parts and replacement

TANK, 5 GALLON, MODEL DT-5

22658

filters

For factory authorized

service, or to order factory

authorized replacement

parts, contact your Wells

authorized service agency,

or call:

DELIMING SOLUTION BOTTLE WITH

QUICK DISCONNECT FITTING

22800

22801

84501

DELIMING SOLUTION BOTTLE (ONLY)

PITCHER, PLASTIC, 4 QT.

ASSEMBLY (STRAINER / PRESSURE

REGULATOR WITH GAUGE /

Wells Manufacturing Co

2 Erik Circle

WATER HAMMER ARRESTOR)

84868

P. O. Box 280

Verdi, NV 89439

phone: (888) 492-2782

PRESSURE REGULATOR (ONLY)

PRESSURE GAUGE (ONLY)

8541-401

8541-402

9012-54

SA 9052

fax:

(888) 492-2783

(Service Parts Dept.)

WATER HAMMER ARRESTOR (ONLY)

WATERLINE “Y” STRAINER (ONLY)

Service Parts Department

can supply you with the

name and telephone

NEUTRALIZER AND DELIMER (concentrate) KAY #55905

Kay Chemical Company

number of the WELLS

AUTHORIZED SERVICE

AGENCY nearest you.

1-800-529-5458

CUSTOMER SERVICE DATA

please have this information available if calling for service

RESTAURANT _____________________________ LOCATION _____________

INSTALLATION DATE ________________________ TECHNICIAN ___________

SERVICE COMPANY ________________________________________________

ADDRESS ___________________________ STATE ______ ZIP__________

TELEPHONE NUMBER (_____)_____-_________

EQUIPMENT MODEL NO. _______________

EQUIPMENT SERIAL NO. _______________

VOLTAGE: (check one)

208

240

Download from Www.Somanuals.com. All Manuals Search And Download.

PRINTED IN UNITED STATES OF AMERICA

Download from Www.Somanuals.com. All Manuals Search And Download.

Whirlpool Washer Dryer W10376238C User Manual
Williams Sound DJ Equipment PPA R35N User Manual
Williams Sound Electronic Keyboard Sonata 88 User Manual
Wilton Lathe 63300 User Manual
Winegard Satellite TV System SK 7002 User Manual
Xerox All in One Printer 4260 XF User Manual
X Micro Tech Headphones BT400GII User Manual
Xpelair Air Conditioner IDH1 8 User Manual
Zanussi Washer Dryer ZWF 1434W User Manual
Zenith Speaker System XBS344 User Manual