Model No. WESY75742
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (under seat)
USER’S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-877-992-5999
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before
Visit our website at
using this equipment. Save this
manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING DECAL PLACEMENT
The decals shown here have been
placed on the resistance system. If a
decal is missing or illegible, please call
our Customer Service Department toll-
free at 1-877-992-5999, Monday through
Friday, 6 a.m. until 6 p.m. Mountain
Time, to order a free replacement decal.
Apply the decal in the location shown.
Keep hands and
fingers clear of
this area.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the resistance system.
1. Read all instructions in this manual before
using the resistance system. Use the resist-
ance system only as described in this manual.
on the high cables only while sitting on the
bench, with the seat in one of the three posi-
tions closest to the upright base, or while
standing on the base plate.
2. It is the responsibility of the owner to ensure
that all users of the resistance system are
adequately informed of all precautions.
11. The crossbar on the top frame is not
designed to be used for pull-up exercises. Do
not hang on the crossbar.
3. The resistance system is intended for home
use only. Do not use the resistance system in
any commercial, rental, or institutional setting.
12. The resistance system is designed to be
used with the included resistance. Do not
use the resistance system with any other
type of resistance.
4. Use the resistance system only on a level
surface. Cover the floor beneath the resist-
ance system to protect the floor.
13. Always disconnect the lat bar from the high
cables when performing an exercise that
does not require it.
5. Make sure that all parts are properly tight-
ened each time the resistance system is
used. Replace any worn parts immediately.
14. Make sure the storage knob is in place and
fully tightened each time the resistance sys-
tem is used.
6. Keep children under 12 and pets away from
the resistance system at all times.
15. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys. Replace all
cables at least every two years.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. The resistance system is designed to sup-
port a maximum user weight of 300 pounds.
16. Do not pull on the cables while the resist-
ance level is being adjusted.
10. Pull on the lower cable only while sitting on
the bench or standing on the base plate. Pull
17. If you feel pain or dizziness while exercising,
stop immediately and begin cooling down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
®
Thank you for selecting the innovative WEIDER PLAT- after reading this manual, please call our Customer
INUM XP800 resistance system. The resistance system Service Department toll-free at 1-877-992-5999,
offers a selection of stations designed to develop every
Monday through Friday, 6 a.m. until 6 p.m. Mountain
major muscle group of the body. Whether your goal is to Time (excluding holidays). To help us assist you, please
tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
resistance system will help you to achieve the specific
results you want.
note the product model number and serial number
before calling. The model number is WESY75742. The
serial number can be found on a decal attached to the
resistance system (see the front cover of this manual).
For your benefit, read this manual carefully before
Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled.
using the resistance system. If you have questions
Crossbar
Top Frame
High Pulley
Lat Bar
Console
Resistance Bar
Squat Pin
Squat Backrest
Backrest
Storage Knob
Low Pulley
Row Plate
Seat
Seat Knob
Base Plate
Leg Lever
ASSEMBLED
DIMENSIONS:
Height: 86 in.
Width: 50 in.
Depth: 85 in.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• Tighten all parts as you assemble them, unless
Make Things Easier for Yourself
instructed to do otherwise.
This manual is designed to ensure that the resist-
ance system can be assembled successfully by
most people. However, it is important to realize
that the versatile resistance system has many
parts and that the assembly process will take
time. Most people find that by setting aside plenty
of time, assembly will go smoothly.
• As you assemble the resistance system, make
sure all parts are oriented as shown in the draw-
ings.
The included Allen wrenches
and the fol-
lowing tools (not included) are required for
assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires two persons.
• One standard screwdriver
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• One Phillips screwdriver
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• For help identifying small parts, use the PART
IDENTIFICATION CHART. Note: Some small
parts may have been pre-attached for shipping. If
a part is not in the parts bag, check to see if it
has been pre-attached.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
1.
1
Before beginning assembly, make sure that
you have read and understand the informa-
tion in the box above. Refer to the PART
IDENTIFICATION CHART for help identifying
small parts.
2
Pull the lower end of the Upper Wire Harness
(71) out of the hole in the back of the Upright (2).
71
Attach the Upright (2) to the Base Plate (1) with
an M10 x 25mm Button Screw (88), an M10
Washer (106), an M10 x 92mm Button Bolt (83),
and an M10 Nylon Locknut (103).
88
106
103
83
1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Insert the connector of the Upper Wire Harness
(71) into the socket of the Lower Wire Harness
(117). The connector should slide easily into the
socket and snap into place. If the connector does
not slide easily and snap into place, turn the con-
nector over and then insert it.
2
6
12
85
Make sure that the connector and wires appear
as shown in the inset drawing. IF THE CONNEC-
TOR IS NOT INSERTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.
117
71
Insert the Mech Frame (6) into the Base Plate (1).
Attach the Mech Frame to the Upright (2) with a
1/2” x 25mm Screw (85) and a 1/2” Lock Washer
(12). Do not tighten the Screw yet.
103
Attach the Mech Frame (6) to the Base Plate (1)
with four M10 Nylon Locknuts (103).
2
Black
Wire
1
Tighten the 1/2” x 25mm Screw (85).
117
Red
103
Wire
71
3. Press the Rail Cap (49) onto the Leg (5). Attach
the Leg to the Rail (4) with two M10 x 64mm
Button Bolts (80), four M10 Washers (106), and
two M10 Nylon Locknuts (103).
3
103
106
4
Holes on
this side
106
49
80
5
4. Lubricate an M10 x 125mm Button Bolt (89) with
grease. Attach the Rail (4) to the Row Plate (28)
with the Bolt, two M10 Washers (106), two 31mm
Spacers (30), and an M10 Nylon Locknut (103).
Do not overtighten the Locknut; the Rail must
be able to pivot easily.
4
29
28
106
103
Tighten the Storage Knob (29) into the Row Plate
(28) and the Rail (4).
30
30
4
106
89
Lubricate
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Insert the Squat Pin (66) into the Upright (2).
Slide the Squat Carriage (19) onto the Upright (2).
5
2
19
66
6. Attach the Top Frame (37) to the Upright (2) with
two M10 x 25mm Button Screws (88), an M10 x
75mm Button Screw (84), three M10 Lock
Washers (75), and an M10 Washer (106).
6
88
37
75
84
2
75
106
7. Pull the excess Upper Wire Harness (71) out of
the Upright (2). Insert the connector on the
Console (67) into the socket on the Upper Wire
Harness. The connector should slide easily into
the socket and snap into place. If the connector
does not slide easily and snap into place, turn the
connector over and then insert it.
7
53
71
2
67
Make sure that the connector and wires appear
as shown in the inset drawing. IF THE CONNEC-
TOR IS NOT INSERTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.
53
Black
Wire
Push the excess Upper Wire Harness (71) into
the Upright (2).
67
Red
Attach the Console (67) to the Upright (2) with
four M4 x 70mm Screws (53).
Wire
71
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Attach a Large Pulley (14) and the Pulley Plate
(68) to the Upright (2) with an M12 x 62mm
Button Bolt (81) and an M12 Nylon Locknut (13).
Do not tighten the Locknut yet.
8
68
14
13
2
81
9. Pull the Upper Cable (121), which is attached
inside of the Mech Frame (not shown), up
9
between the Upright (2) and the Pulley Plate (68).
121
11
14
Attach another Large Pulley (14) to the Upright (2)
and Pulley Plate (68) with an M12 x 62mm Button
Bolt (81) and an M12 Nylon Locknut (13). Make
sure that the Upper Cable (121) is between the
two Pulleys.
90
13
68
81
Hold the 38mm Spacer (90) inside the loop of the
Upper Cable (121), and between the Upright (2)
and the Pulley Plate (68). Attach the Spacer with
an M10 x 58mm Button Screw (11). Make sure
the ends of the Cable do not wrap around
each other below the Spacer and the Large
Pulleys (14) used in steps 8 and 9 (refer to the
CABLE DIAGRAM on page 18).
2
Tighten the M12 Nylon Locknuts (13) used in
steps 8 and 9.
10. Attach a Small Guide Spacer (18), a Large Guide
Spacer (17), and two Crossbar Guides (15) to the
Upright (2) with an M10 x 152mm Bolt (86).
10
Pull the Upper Cable (121) up between the
Crossbar Guides (15). Press the metal cover on
the Cable into the groove in the Crossbar Block
(16). Attach a Small Guide Spacer (18), the
Crossbar Block, the two Crossbar Guides (15), an
M10 Thick Washer (54), and the two Tethers (70)
to the Upright (2) with another M10 x 152mm Bolt
(86). Do not tighten the Bolt yet.
17
15
18
86
Metal
Cover
54
121
2
86
70
Groove
16
18
9
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Insert the Resistance Bar (9) between the
Crossbar Guides (15), and center it on the
Crossbar Block (not shown).
11
15
Press a Pulley Bracket (10) onto the Resistance
Bar (9). Screw a 3/8” x 38mm Tension Screw
(114) into the Pulley Bracket a couple of turns.
Make sure the hexagonal hole in the Screw is
on the outside of the Bracket.
70
103
54
9
Attach a Tether (70) to the Pulley Bracket (10) at
the upper hole, with an M10 x 64mm Button Bolt
(80), an M10 Thick Washer (54), and an M10 Nylon
Locknut (103).
10
80
114
Repeat on the other side of the Resistance
Bar (9). Then, tighten the lower M10 x 152mm
Bolt (86) used in step 10.
12
13
12. Hold a Large Pulley (14) inside the Upper Cable
(121). Attach the Pulley to a Pulley Bracket (10)
with an M12 x 58mm Button Bolt (87) and an M12
Nylon Locknut (13). Make sure that the Cable is
routed as shown in the CABLE DIAGRAM on
page 18.
10
14
87
121
13. Hold a Large Pulley (14) inside the Upper Cable
(121). Attach the Pulley to the other Pulley
Bracket (10) with an M12 x 58mm Button Bolt
(87) and an M12 Nylon Locknut (13). Make sure
that the Cable is routed as shown in the
CABLE DIAGRAM on page 18.
13
13
Tighten the two 3/8” x 38mm Tension Screws
(114) an equal number of turns.
114
121
10
14
87
14. Attach the Leg Lever (56) to the Leg (5) with a
Leg Station Pin (60). Slide a Cotter Pin (113) onto
the Leg Station Pin.
14
5
113
56
60
10
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Slide a Pad Tube (50) into the Leg (5). Slide two
Large Foam Pads (52) onto the Pad Tube.
15
Attach the other Pad Tube (50) to the Leg
Lever (56) in the same manner.
5
52
56
50
52
50
16. Insert the rod on the Backrest Frame (32) into the
slot in the Seat Carriage (44). Hold the Backrest
Frame vertically over the Seat Carriage and
slide the rod into the slot, as shown in the
inset drawing.
16
32
Rod
Slot
44
32
44
17. Adjust the tension on the upper cable (not shown)
as described in UPPER CABLE ADJUSTMENT
on the following page.
18 Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
.
ADJUSTMENTS, beginning on page 13.
Before using the resistance system, turn on the console and change the resistance setting as
described in CONSOLE OPERATION on page 16.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
UPPER CABLE ADJUSTMENT
After completing the assembly of the resistance system, the tension on the Upper Cable (121) will need to be
adjusted. Also, the Upper Cable can stretch slightly when it is first used. When this occurs, the upper cable ten-
sion will need to be readjusted. Follow the steps below to adjust the upper cable tension.
1. Connect the two Tension Gauges (115, 116)
1
together using the magnet.
115
Magnet
116
2. Plug in the resistance system as described in
2
PLUGGING IN THE RESISTANCE SYSTEM on
page 16. Use the Console (not shown) to adjust
the resistance setting of the system to the highest
setting, as described in Select a resistance set-
ting on page 16.
10
115
121
70
Squeeze the Upper Cable (121) together near a
Large Pulley (14). Hook the ends of the Tension
Gauges (115, 116) around the Upper Cable as
shown. Do not hook the ends of the Tension
Gauges around the Tether (70), which is
attached to the back of the Pulley Bracket
(10).
116
121
14
115
121
Slide the Tension Gauges (115, 116) next to the
Large Pulley (14) as shown in the inset drawing.
116
14
3
3. Locate the 3/8” x 38mm Tension Screw (114) on
each end of the Resistance Bar (9). Alternately
tighten each Screw one turn at a time until the
two Tension Gauges (115, 116) are pulled apart
by the Upper Cable (121).
9
114
The upper cable tension is now properly adjusted.
115
116
121
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
This section explains how to adjust the resistance system. See the EXERCISE GUIDELINES on page 20 for
important information about how to get the most benefit from your exercise program. Also, refer to the accompa-
nying exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the resistance system is used. Replace worn parts immedi-
ately. The resistance system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use
solvents. The resistance bar can be cleaned with a vinyl and rubber protectant, available at an automotive or
department store.
ATTACHING THE HIGH PULLEYS
37
To use a high pulley, slide the hook on the Pulley
Housing (39) onto an hook on the Top Frame (37).
Attach the end of the High Cable (101) without the
ball to the end of the Lower Cable (120) with a Cable
Clip (94). Attach the other high pulley in the same
manner.
39
Ball
Remove the high pulleys when not in use.
101
120
94
USING THE LEG LEVER
To use the Leg Lever (56), attach it to the Leg (5) with
a Leg Station Pin (60). Slide a Cotter Pin (113) onto
the Leg Station Pin.
113
56
5
40
Route the hook end of the Leg Lever Cable (102)
under the 90mm Pulley (40) in the Leg (5), and attach
it to the Leg Lever (56). Make sure the hook is ori-
ented as shown when attaching it to the Leg
Lever. Insert a Leg Station Pin (60) into the Leg,
under the Cable. Slide a Cotter Pin (113) onto the Leg
Station Pin.
102
113
60
60
Hook
See the inset drawing. Attach a long end of the Leg
Lever Cable (102) to one end of the Lower Cable
(120) with a Cable Clip (94). Attach the other long
end of the Leg Lever Cable to the other end of the
low cable in the same manner.
94
102
120
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE SQUAT ARM
27
To adjust the Squat Arm (20), remove the Squat Knob
(27) from Squat Carriage (19). Move the Arm to the
up or down position, and reengage the Knob into the
Squat Carriage.
19
20
ATTACHING THE SQUAT STATION
To use the squat station, first remove the backrest
(see ADJUSTING THE BACKREST below). Next,
adjust the squat arm to the up position (see ADJUST-
ING THE SQUAT ARM above). Then, insert a Squat
Pin (66) into the correct hole in the Upright (2).
Finally, attach each end of the Lower Cable (120) to
the Squat Carriage (19) with a Carriage Strap (77)
and two Cable Clips (94).
20
94
Note: The Squat Pin (66) will determine the lowest
point to which the Squat Carriage (19) can
descend. The Squat Carriage should not be able to
descend so low that the user could become
trapped under the Squat Arm (20).
19
2
77
66
94
120
ADJUSTING THE BACKREST
35
The Backrest (35) can be used in a level position or an
inclined position. To use the Backrest in a level posi-
tion, secure the Seat Carriage (44) at the adjustment
hole in the Rail (4) closest to the Leg (not shown) (see
ADJUSTING THE SEAT on page 15).
2
To use the Backrest (35) in an inclined position,
secure the Seat Carriage (44) at one of the other
adjustment holes in the Rail (4). Rest the Backrest
against the Upright (2).
For row exercises, remove the Backrest (35) from the
Seat Carriage (44). Hold the Backrest vertically over
the Seat Carriage and lift the rod out of the slot (see
the inset drawing).
4
Rod
32
Slot
44
44
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE ACCESSORIES
To attach the Lat Bar (82) to the high pulleys, first
attach the high pulley to the resistance system (see
ATTACHING THE HIGH PULLEYS on page 13). Then,
attach the Lat Bar to a High Cable (101) with a Cable
Clip (94). Attach the Lat Bar to the other High Cable
in the same manner.
101
94
101
The Handles (not shown) and the Ankle Strap (not
shown) can be attached to the High Cables (101) or
the lower cable (not shown) with Cable Clips (94).
Attach the Hip Strap (not shown) to the ends of the
lower cable with two Cable Clips.
82
ADJUSTING THE SEAT
Pin
35
The Seat (45) can be secured at various positions on
the Rail (4). To move the Seat, pull the Seat Knob
(48) out as far as it will go and slide the Seat to the
desired position. Engage the Seat Knob into an
adjustment hole in the Rail.
45
44
48
“L”-Slot
To perform row exercises, the hip strap must be
attached to the mech cable (see ATTACHING THE
ACCESSORIES, above), and the Seat Carriage (44)
must be able to roll along the Rail (4). First, remove
the Backrest (35) from the Seat Carriage (see
ADJUSTING THE BACKREST on page 14). Then,
pull the Seat Knob (48) out as far as it will go, and
turn the Knob so that the pin rests at the end of the
“L”-shaped slot (see the inset drawing).
44
4
48
Adjustment
Hole
37
STORING THE RESISTANCE SYSTEM
To store the resistance system, first remove the Leg
Lever (not shown) from the resistance system. Secure
the Seat Carriage (44) at the position closest to the
Leg (5) (see ADJUSTING THE SEAT above). Next,
remove the Storage Knob (29) from the Row Plate
(28). Lift the Leg toward the Top Frame (37), and tight-
en the Storage Knob into the side of the Row Plate
and into the Rail (4).
Hold in
this area
5
44
4
To move the resistance system, stand behind the
Upright (2) and place the toe of your shoe on the end
of the Base Plate (1) and hold the resistance system
in the indicated area. Tilt the resistance system back
onto the Wheels (65) and roll it to the new location.
2
WARNING:
Make sure that
Storage Knob (29) is in place and fully tight-
ened each time the resistance system is used.
28
1
65
29
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE OPERATION
FEATURES OF THE CONSOLE
PLUGGING IN THE RESISTANCE SYSTEM
Plug the indicated
end of the
Transformer (72) into
the Back Mech
Cover (8). Plug the
other end of the
Transformer into a
Console
8
120-volt outlet. All
indicators and dis-
plays on the console
72
will flash once; the console will then be ready for use.
The motor may be heard while the resistance system
calibrates itself. Important: Always plug in the trans-
former when using the resistance system.
MANUAL OPERATION
1. Plug in the transformer.
Program
Buttons
Plug the transformer into a 120-volt outlet (see
PLUGGING IN THE RESISTANCE SYSTEM
above). Important: Always plug in the trans-
former when using the resistance system.
Main
Note: When the power is on, the words MANUAL
MODE will appear in the main display. To use a pro-
gram, see PROGRAM OPERATION on page 17. To
return to the manual mode while the console is run-
ning a program, press and hold the NEXT button.
Display
Resistance
Display
If no buttons are pressed and no cables are pulled
for ten minutes, the console will go to sleep. Press
any button to resume exercising.
Sets
Display
2. Select a resistance setting.
Reps
The current resistance setting will appear in the
resistance display. To select a different resistance
setting, first make sure that no cables are being
pulled. Next, press the resistance + and – buttons.
Each time a button is pressed, the resistance set-
ting will increase or decrease by 1 pound. To
change the resistance setting quickly, hold down
one of the buttons.
Display
The heart of the resistance system is the digital resist-
ance training console. The console offers both a manu-
al mode and nine workout programs. When the manual
mode is selected, the resistance setting can be
changed with the touch of a button. When a program is
selected, the console will guide you through an effec-
tive upper body, ab and back, or lower body workout.
Note: While the resistance setting is changing, the
motor will be heard. To prevent damage to the
motor, do not pull any of the cables while the
resistance setting is changing. If a cable is
pulled, the words RELEASE HANDLES AND
READJUST RESISTANCE AS DESIRED may
appear in the main display.
To use the manual mode of the console, follow the
steps at the right. To use a program, see page 17.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The resistance system uses progressive
resistance. As the resistance bar begins to bend,
the amount of resistance will increase gradually. As
the bar bends further, the resistance will increase
rapidly, up to 340 pounds.
3. Row for five minutes to warm up.
When a program is selected, the words CARDIO
ROW will appear in the main display. To warm up,
perform the cardio row exercise while the main dis-
play counts down from 5 minutes.
3. Enter the numbers of sets and repetitions that
you plan to complete for an exercise.
Note: To see the correct form for the cardio row
exercise, see the included exercise guide. If the
resistance setting is too high or too low, select a dif-
ferent resistance setting by pressing the resistance
+ and – buttons.
To enter the number of sets that you plan to do,
press the SETS + and – buttons. To enter the num-
ber of repetitions that you plan to do, press the
REPS + and – buttons.
4. Adjust the resistance setting and the numbers of
sets and repetitions for the exercise if desired.
Note: If you do not enter the numbers of sets and
repetitions that you plan to do, the console will
count the total number of repetitions that you com-
plete during your workout.
The name of an exercise in the program will appear
in the main display. The recommended resistance
setting and the recommended numbers of sets and
repetitions for the exercise will appear in the three
displays below the main display.
4. Perform the exercise.
If you have entered numbers of sets and repeti-
tions, the console will count down the repetitions
and sets you have completed. When you complete
the exercise, repeat steps 2 and 3 above for each
exercise that you perform.
The recommended resistance setting and the rec-
ommended numbers of sets and repetitions may be
too high or too low for you, depending on such fac-
tors as your body size and your physical condition. If
desired, adjust the resistance setting and the num-
bers of sets and repetitions by pressing the + and –
buttons below each display.
5. Unplug the transformer.
When you complete your workout, unplug the trans-
former from the 120-volt outlet.
5. Perform the exercise.
As you perform the exercise, the console will count
down the numbers of sets and repetitions you have
completed.
PROGRAM OPERATION
1. Plug in the transformer.
When you complete the exercise, the word REST-
ING will appear in the main display. It is recom-
mended that you rest while the main display counts
down.
Plug the transformer into a 120-volt outlet (see
PLUGGING IN THE RESISTANCE SYSTEM on
page 16). Important: Always plug in the trans-
former when using the resistance system.
6. Perform the remaining exercises in the program.
Note: If no buttons are pressed and no cables are
pulled for ten minutes, the console will go to sleep.
Press any button to resume exercising.
After you have completed an exercise in the pro-
gram, press the NEXT button, and the name of the
next exercise will appear in the main display. Repeat
steps 4 and 5 above for the exercise.
2. Select a program.
When the power is on, the words SELECT PRO-
GRAM will appear in the main display. To select a
program, press one of the nine program buttons.
The indicator on the button you press will light.
Note: The program may include the same exercise
twice, with different resistance settings and different
numbers of sets and repetitions. If you wish to skip
any part of the program, press the NEXT button to
advance to the next part of the program.
Note: The console offers three upper body pro-
grams, three ab and back programs, and three
lower body programs. If you wish to exercise your
upper body and if your goal is to lose weight, for
example, press the LOSE WEIGHT button below
the words UPPER BODY PROGRAMS.
When you complete the program, the words WORK-
OUT COMPLETE will appear in the main display.
7. Unplug the transformer.
When you complete your workout, unplug the trans-
former from the 120-volt outlet.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE DIAGRAM
The cable diagram shows the proper routing of the
Upper Cable (121). Use the diagram to make sure
that the cable has been assembled correctly. If the
cable has not been correctly routed, the resistance
system will not function properly and damage may
occur. The numbers show the correct route for the
cable. Make sure that the ends of the cable do not
wrap around each other between positions 1 and
2, and 6 and 7.
Upper Cable (121)
4
5
6
2
3
1
7
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
RECALIBRATING THE CONSOLE
To recalibrate the Console (67), first plug in the resist-
ance system (see PLUGGING IN THE RESISTANCE
SYSTEM on page 16). Then, press and hold the
NEXT button and the MOTORIZED WEIGHT
ADJUSTMENT + button for five seconds. When the
buttons are released, a number will appear in the
REPS display. Press the NEXT button again, then
press the MOTORIZED WEIGHT ADJUSTMENT +
button; this will start the recalibration process. This
may take a few minutes as the motor moves between
the lowest and highest resistance settings. When the
motor finishes, unplug the transformer from the 120-
volt outlet.
67
The Console (67) will be recalibrated. Use the resist-
ance system as described in the CONSOLE OPERA-
TION section, starting on page 16.
CLEANING THE BAR GUIDES
Over time, dust may build up on the Crossbar Guides
(15), causing a squeaking noise as the resistance
system is used. If this occurs, wipe off the Crossbar
Guides with a damp cloth and a mild, non-abrasive
detergent. Do not use solvents.
15
ADJUSTING THE RESISTANCE
When the resistance setting changes, the motor will
be heard. To prevent damage to the motor, do not
pull any of the cables while the resistance setting
is changing. If a cable is pulled, the words
RELEASE HANDLES AND READJUST RESIST-
ANCE AS DESIRED may appear in the main display
on the console.
If this message is displayed repeatedly but no cable
is being pulled, there may be too much tension on the
upper cable (A). Adjust the tension as described
below.
To decrease the tension on the upper cable (A), turn
the two 3/8” x 38mm Tension Screws (114) twice,
counterclockwise. Select the desired resistance set-
ting. Repeat this step if necessary.
A
114
19
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-
cles will continually adapt and grow as you progres-
sively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
ing it during the first few months of your exercise pro-
gram. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immedi-
ately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise pro-
gram.
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
WARMING UP
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
right for you. Begin with 3 sets of 8 repetitions for each your body for more strenuous exercise by increasing
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a mod- Each workout should include 6 to 10 different exercis-
erate percentage of their capacity. Select a moderate
amount of resistance and increase the number of rep-
etitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by com-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
pleting more sets rather than by using high amounts of Schedule your workouts for the time of day when your
resistance.
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
Cross Training
Cross training is an efficient way to get a complete and moving only the appropriate parts of the body.
well-balanced fitness program. An example of a bal-
anced program is:
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an elliptical or
exercise cycle, on Tuesday and Thursday.
• Rest from both strength training and aerobic exercise The repetitions in each set should be performed
for at least one full day each week to give your body
time to regenerate.
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
The combination of strength training and aerobic exer- during the exertion stage of each repetition and inhale
cise will reshape and strengthen your body, plus devel- during the return stroke. Never hold your breath.
op your heart and lungs.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The
ideal resting periods are:
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for three minutes after each set for a muscle
building workout.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
For motivation, keep a record of each workout. The
chart on pages 22 and 23 of this manual can be pho-
tocopied and used to schedule and record your work-
outs. List the date, the exercises performed, the resist-
ance used, and the numbers of sets and repetitions
completed. Record your weight and key body meas-
urements at the end of every month. Remember, the
key to achieving the greatest results is to make exer-
cise a regular and enjoyable part of your everyday life.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A. Sternomastoid (neck)
A
B. Pectoralis Major (chest)
P
Q
C. Biceps (front of arm)
L
B
D. Obliques (waist)
E. Brachioradials (forearm)
R
S
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
C
D
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
E
T
F
M
N
U
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
G
H
I
V
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
W
X
J
K
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WESY75742
R0704A
Description
Key No. Qty.
Description
Key No. Qty.
Description
Key No. Qty.
1
2
1
1
1
1
1
1
1
1
1
2
1
Base Plate
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
3
1
1
2
1
0
2
2
2
1
2
2
1
1
1
1
2
1
M10 Thick Washer
Leg Lever Bumper
Leg Lever
99
2
M10 x 78mm
Button Bolt
Upright
3
Upright Cover
Rail
100
101
102
103
2
2
M4 x 38mm Screw
High Cable
4
Leg Lever Bushing
Leg Station Cap
not used
5
Leg
1
Leg Lever Cable
M10 Nylon
6
Mech Frame
Front Mech Cover
Back Mech Cover
Resistance Bar
Pulley Bracket
M10 x 58mm
Button Screw
1/2” Lock Washer
M12 Nylon
33
7
Leg Station Pin
22mm Spacer
Leg Outer Cap
Base Plate Foot
Wheel Insert
Wheel
Locknut
8
104
4
M10 x 34mm
Button Bolt
9
10
11
105
106
107
108
109
4
14
4
M6 x 38mm Screw
M10 Washer
M6 Washer
12
13
1
4
Squat Pin
2
M5 x 56mm Screw
M4 x 7mm
Console
2
Locknut
Pulley Plate
Cable Guide
Tether
Machine Screw
45mm Square
Inner Cap
14
15
16
17
4
2
1
1
Large Pulley
Crossbar Guide
Crossbar Block
Large Guide
Spacer
110
1
Upper Wire
Harness
111
112
4
2
M4 x 20mm Screw
M4 x 5mm Screw
(Round Head)
Cotter Pin
72
73
1
2
Transformer
Pulley Pivot
Bracket
18
2
Small Guide
Spacer
113
114
2
2
3/8" x 38mm
Tension Screw
Tension Gauge
Tension Gauge
w/magnet
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
1
2
4
1
2
2
1
8
1
1
1
2
1
1
1
2
Squat Carriage
Squat Arm
74
2
Pivot Bracket
Bushing
115
116
1
1
Short Handgrip
Squat Pivot Tube
Squat Arm Roll Pin
Small Foam Pad
Squat Backrest
Carriage Wheel
Squat Knob
Row Plate
75
76
77
78
3
1
2
4
M10 Lock Washer
M5 x 35mm Screw
Carriage Strap
M10 x 40mm
Button Bolt
117
118
1
4
Lower Wire
Harness
Mech M10 Nylon
Locknut
79
80
4
6
16mm Spacer
M10 x 64mm
Button Bolt
119
120
121
122
123
124
125
126
127
128
2
1
1
8
2
2
1
2
2
1
Spacer Magnet
Lower Cable
Upper Cable
Large Mech Pulley
Small Mech Pulley
Plate Pulley
Storage Knob
31mm Spacer
Rail Insert
81
2
M12 x 62mm
Button Bolt
82
83
1
1
Lat Bar
Backrest Frame
Backrest Cap
25mm Square
Inner Cap
M10 x 92mm
Button Bolt
Lead Screw Assm.
Mech Cap
84
85
5
1
M10 x 75mm
Button Bolt
6mm Spacer
Plate Pulley
35
36
37
38
1
3
1
2
Backrest
1/2” x 25mm
Screw
Plastic Foot
Top Frame
Spacer
86
87
2
2
M10 x 152mm Bolt
M12 x 58mm
Button Bolt
129
130
131
132
133
134
135
2
1
2
2
1
1
2
M10 Mech Washer
Mech Cotter Pin
Limit Switch
38mm Round
Inner Cap
39
40
41
42
43
44
45
46
47
48
49
50
51
2
5
8
9
4
1
1
1
1
1
1
2
4
Pulley Housing
90mm Pulley
M6 x 16mm Screw
M4 x 16mm Screw
11mm Spacer
Seat Carriage
Seat
88
89
3
1
M10 x 25mm
Button Screw
M10 x 125mm
Button Bolt
M10 x 89mm Bolt
M10 x 95mm Bolt
M10 x 102mm Bolt
M10 x 16mm
Button Screw
M3 x 19mm Screw
M10 x 122mm Bolt
Clevis Pin
90
91
92
1
1
1
38mm Spacer
Reed Sensor
M10 x 85mm
Button Bolt
136
137
138
139
140
#
4
1
1
4
1
1
1
1
Pop Pin
Knob Spring
Seat Knob
93
4
M10 x 44mm
Button Bolt
M3 Nut
M10 x 44mm Bolt
User’s Manual
Exercise Guide
Large Allen
Rail Cap
94
95
96
97
98
4
2
2
1
1
Cable Clip
Pad Tube
Long Handle
Short Handle
Hip Strap
#
19mm Round
Inner Cap
#
Wrench
52
53
4
4
Large Foam Pad
M4 x 70mm Screw
Ankle Strap
#
1
Small Allen
Wrench
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART IDENTIFICATION CHART AND PART LIST/
EXPLODED DRAWING. SAVE THIS PART IDENTIFICATION CHART
AND PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE.
PART IDENTIFICATION CHART—Model No. WESY75742
M10 x 58mm Button Screw (11)
M12 x 58mm Button Bolt (87)
M10 x 25mm Button Screw (88)
1/2" x 25mm Screw (85)
38mm Spacer (90)
31mm Spacer (30)
3/8" x 38mm Tension Screw (114)
M12 x 62mm Button Bolt (81)
M10 x 64mm Button Bolt (80)
M12 Nylon Locknut (13)
M10 Nylon Locknut (103)
M4 x 70mm Screw (53)
1/2" Lock Washer (12)
M10 x 75mm Button Bolt (84)
M10 x 85mm Button Bolt (92)
M10 Washer (106)
M10 Thick Washer (54)
M10 Lock Washer (75)
M10 x 92mm Button Bolt (83)
M10 x 125mm Button Bolt (89)
M10 x 152mm Bolt (86)
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WESY75742
R0704A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-877-992-5999, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information:
• The MODEL NUMBER of the product (WESY75742)
™
• The NAME of the product (WEIDER PLATINUM XP800 resistance system)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in the
center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ten (10) years from the date of pur-
chase. ICON warrants the resistance bar for the lifetime of the product. This warranty extends only to the
original purchaser. ICON's obligation under this warranty is limited to repairing or replacing the warrant-
ed parts. This warranty does not extend to any product or damage to a product caused by or attributable
to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center; products used for commercial or rental purposes; or products used as store
display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 215580 R0704A
Printed in USA © 2004 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|