®
Patent Pending
Model No. WESY97310
Serial No.
USER’S MANUAL
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if there
are missing or damaged parts,
we will guarantee complete satis-
faction through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the innovative and versatile
WEIDER® PRO 9940 home gym. The WEIDER® PRO
9940 offers a unique selection of weight stations
designed to develop every major muscle group of the
body. Whether your goal is to tone your body, build
dramatic muscle size and strength or improve your
cardiovascular system, the WEIDER® PRO 9940
makes it easy to achieve the results you want.
Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
please note the product model number and serial
number before calling. The model number is
WESY97310. The serial number can be found on a
decal attached to the home gym (see the front cover
of this manual).
For your benefit, read this manual carefully before
using the WEIDER® PRO 9940 home gym. If you
have additional questions, please call our Customer
Please use the drawing below to familiarize your-
self with the major parts and how they fit together.
ASSEMBLED
Lat Bar
DIMENSIONS:
Height: 77 in.
Width: 80 in.
Depth: 55 in.
High Pulley
Station
Butterfly
Arms
Ab Pulley
Station
Backrest
Backrest
Curl Pad
Press Arms
Leg Press
Plate
Foam Pads
Seat
Leg
Lever
Leg
Press
Lever
Low Pulley
Station
Weight
Stacks
Foot Plate
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Note: This introduction will save you more time
than it takes to read it!
Identifying Parts
To help you identify the small parts used in assem-
bly, we have included a PART IDENTIFICATION
CHART located in the center of this manual. Place
the chart on the floor or work table and use it to
quickly identify different parts as you open the pack-
ages for each step. Note: Some small parts may
have been pre-attached for shipping. If a part is not
in the parts bag, check to see if it has been pre-
attached.
Making Things Easier for Yourself
Everything in this manual is designed to ensure
that our products can be assembled successfully
by anyone. However, it is important to realize
that your new equipment is a sophisticated prod-
uct with many small parts. The assembly process
will take time—possibly several hours. Most peo-
ple find that by setting aside plenty of time, and
by deciding to make the task enjoyable, assem-
bly will go smoothly. You may want to complete
the process over a couple of evenings.
Orienting Parts
As you assemble this product, be sure that all parts
are oriented as shown in the drawings.
Tightening Parts
Tighten all parts as you assemble them, unless
instructed to do otherwise.
Some assembly steps require two people.
Giving Yourself a Good Start
Before you begin the assembly process itself, take
the time to complete the steps outlined here.
Lining Up the Tools
Assembly requires the following tools (not included):
• Two (2) adjustable wrenches
• One (1) standard screwdriver
• One (1) phillips screwdriver
• One (1) rubber mallet
Clearing the Workspace
Clear a workspace that is large enough to hold all
parts and allow you to walk all the way around the
assembled equipment.
Unpacking the Box
To make the assembly process as smooth as possi-
ble, we have broken it into separate stages. All parts
used in each stage are found in individual packages
in the shipping box. Place all parts in a cleared area
and remove the packing materials. Do not dispose of
the packing materials until assembly is completed.
• Lubricant, such as grease or petroleum jelly,
and soapy water
• Tape, such as clear tape or masking tape
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end wrenches
or a set of ratchet wrenches.
Important: Wait until you begin each assembly
stage to open the parts bag labeled for that
assembly stage.
The Four Stages of the Assembly Process
Frame Assembly
Cable Assembly
You will begin by assembling the base and the
upright frames that serve as the skeleton of the
equipment.
This stage completes the cables and pulleys that
connect the moving arms with each other and with
the weights.
Seat Assembly
Arm Assembly
This stage completes the press and butterfly arms
that you operate while you are exercising.
This final stage completes the seat and backrest
that support your body while you are exercising.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1a
Frame Assembly
28
1. Before beginning, make sure that you have read
and understood the information on page 4.
28
4
28
95
Locate and open the parts bag labeled “FRAME
ASSEMBLY.”
92
5
92
See drawing 1a. Press a 2” Square Inner Cap (28)
into each end of the Butterfly Base (4). Press two 2”
Square Inner Caps (28) into the Weight Base (5).
28
Insert four 5/16” x 2 1/2” Carriage Bolts (92) up
through the indicated holes in the Butterfly Base (4).
Insert a 3/8” x 3 1/2” Carriage Bolt (95) up through
the hole at the end of the Butterfly Base. Note: If the
Bolts fall out, secure them by putting a small
piece of tape over the head of each Bolt. Place the
Butterfly Base flat on the floor.
1b
89
93
64
See drawing 1b. Attach the Weight Base (5) to the
Butterfly Base (4) with two 5/16” x 2 3/4” Bolts (89), a
Support Plate (93) with 3 1/2” center holes, and two
5/16” Nylon Locknuts (64). Do not tighten the Nylon
Locknuts yet.
64
4
5
Note: There are three kinds of support plates. The
main difference between them is the distance
between the holes. When you need a support
plate, find the type with holes that will fit over the
bolts you are using.
2a
5
24
63
63
28
2. See drawing 2a. Press a 2” Square Inner Cap (28)
57
57
into the end of the Press Base (6).
Attach a 3 1/2” Pulley (24) to each of the brackets on
the Weight Base (5) with a 3/8” x 1 3/4” Bolt (57) and
a 3/8” Nylon Jamnut (63).
6
102
101
92
Insert four 5/16” x 2 1/2” Carriage Bolts (92) up
through the indicated holes in the Press Base (6).
Insert a 3/8” x 2 1/2” Carriage Bolt (101) and a 3/8 x
4” Carriage Bolt (102) up through the indicated holes
at the end of the Press Base (6).
92
2b
5
See drawing 2b. Attach the Press Base (6) to the
Weight Base (5) with two 5/16” x 2 3/4” Bolts (89), a
Support Plate with 3 1/2” center holes (93), and two
5/16” Nylon Locknuts (64). Do not tighten the Nylon
Locknuts yet.
64
64
93
6
89
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Place the bracket on the lower end of the Butterfly
Upright (1) over the indicated 5/16” x 2 1/2” Carriage
Bolts (92) in the Butterfly Base (4). Hand tighten two
5/16” Nylon Locknuts (64) onto the Bolts. Do not
tighten the Nylon Locknuts yet.
3
1
64
4
92
4. Press three 2” Square Inner Caps (28) into the
Butterfly Top Frame (33). Press two 1” Round Inner
Cap (86) into the top of the Butterfly Top Frame (33).
4
89
93
86
28
28
Attach the Butterfly Top Frame (33) to the indicated
bracket at the top of the Butterfly Upright (1) with two
5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2”
center holes (93), and two 5/16” Nylon Locknuts (64).
33
64
28
1
5. Attach the Butterfly Seat Frame (14) to the Front Leg
(20) with two 5/16” x 2 3/4” Bolts (89), two 5/16”
Washers (36), and two 5/16” Nylon Locknuts (64). Do
not tighten the Nylon Locknuts yet.
5
64
1
64
89
64
36
14
Slide the bracket on the Front Leg (20) onto the two
5/16” x 2 1/2” Carriage Bolts (92) in the Butterfly Base
(4). Hand tighten two 5/16” Nylon Locknuts (64) onto
the Bolts. Do not tighten the Nylon Locknuts yet.
36
64
64
89
20
Attach the Butterfly Seat Frame (14) to the Butterfly
Upright (1) with two 5/16” x 2 3/4” Bolts (89), two
5/16” Washers (36) and two 5/16” Nylon Locknuts
(64). Do not tighten the Nylon Locknuts yet.
4
92
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press a 2” Square Inner Cap (28) half way into the
top of the Front Leg (20). Press a 2” Square Inner
Cap (28) into each end of the Small Leg Lever (41).
6
63
40
28
28
Attach the Bumper (40) to the indicated hole in the
Front Leg (20) with a 1” Tap Screw (80).
62
41
Lubricate the 3/8” x 3 1/4” Bolt (62). Attach the Small
Leg Lever (41) to the bracket on the Front Leg (20)
with the Bolt and a 3/8” Nylon Jamnut (63). Do not
overtighten the Nylon Jamnut; it must be easy to
pivot the Leg Lever.
20
80
Lubricate
28
7. Press a 1” Square Inner Cap (98) into the small tube
on the Press Upright (2).
7
64
Place the bracket on the lower end of the Press
Upright (2) over the indicated 5/16” x 2 1/2” Carriage
Bolts (92) in the Press Base (6). Hand tighten two
5/16” Nylon Locknuts (64) onto the Bolts. Do not
tighten the Nylon Locknuts yet.
92
Place the bracket on the lower end of the Support
Frame (3) over the indicated 3/8” x 2 1/2” Carriage
Bolt (101) and the 3/8” x 4” Carriage Bolt (102) in the
Press Base (6). Hand tighten a 3/8” Nylon Jamnut
(63) onto the 3/8” x 2 1/2” Carriage Bolt (101). Do not
tighten the Nylon Jamnut yet.
64
3
2
98
Note: Do not thread a Jamnut (63) onto the 3/8” x
4” Carriage Bolt (102) yet.
63
Attach the Support Frame (3) to the Press Upright (2)
with two 5/16” x 2 1/2” Carriage Bolts (92) and two
5/16” Nylon Locknuts (64). Do not tighten the Nylon
Locknuts yet.
64
102
101
6
92
89
8. Press a 2” Square Inner Cap (28) into the Press Top
Frame (9).
8
28
Attach the Press Top Frame (9) to the indicated
bracket at the top of the Press Upright (2) with two
5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2”
center holes (93), and two 5/16” Nylon Locknuts (64).
93
9
2
64
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Press a 2” Square Inner Cap (28) into the Press Seat
Frame (7).
9
89
36
64
7
Slide the bracket on the Press Seat Frame (7) onto
the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the
Press Base (6). Hand tighten two 5/16” Nylon
Locknuts (64) onto the Bolts. Do not tighten the
Nylon Locknuts yet.
36
28
89
2
64
64
Attach the Press Seat Frame (7) to the Press Upright
(2) with two 5/16” x 2 3/4” Bolts (89), two 5/16”
Washers (36), and two 5/16” Nylon Locknuts (64). Do
not tighten the Nylon Locknuts yet.
6
92
10. Lubricate the 3/8” x 3” Bolt (88). Attach the Leg Press
Lever (83) to the Press Base (6) with the Bolt and a
3/8” Nylon Locknut (50). Do not overtighten the
Nylon Locknut; the Leg Press Lever must pivot
easily.
10
83
6
50
Lubricate
88
11. Place two Weight Bumpers (51) over the indicated
holes in the Weight Base (5). Slide a Weight Guide
(15) into each of the holes.
11
15
16
Attach the indicated Weight Guide (15) to the Weight
Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat
Washers (48), and a 3/8” Nylon Locknut (50).
Groove
Pin
Slide six Weights (21) onto the Weight Guides (15).
Make sure the Weights are turned so the pin
grooves point towards the floor.
17
21
18
Press a Weight Tube Bumper (18) into the lower end
of the Short Weight Tube (17). Slide the Weight Tube
into the center holes in the Weights (21).
Pin
Grooves
Slide a Top Weight (16) onto the Weight Guides (15).
Note: Make sure the Top Weight is turned so the
groove fits over the welded pin on the Weight
Tube (17).
51
48
50
5
48
46
8
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Place two Weight Bumpers (51) over the indicated
holes in the Weight Base (5). Slide a Weight Guide
(15) into each of the holes.
12
15
Attach the indicated Weight Guide (15) to the Weight
Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat
Washers (48), and a 3/8” Nylon Locknut (50).
16
Groove
Pin
Slide ten Weights (21) onto the Weight Guides (15).
Make sure the Weights are turned so the pin
grooves point towards the floor.
70
18
Press a Weight Tube Bumper (18) into the lower end
of the Long Weight Tube (70). Slide the Weight Tube
into the center holes in the Weights (21).
21
Pin
Grooves
Slide a Top Weight (16) onto the Weight Guides (15).
Note: Make sure the Top Weight is turned so the
groove fits over the welded pin on the Weight
Tube (70).
51
51
50
48
48
46
5
13. Place the Weight Top Frame (66) on the indicated
brackets on the Uprights (1 and 2). Note: The four
Weight Guides (15) must be behind the Weight
Top Frame, as shown in step 14.
13
46
46
34
Attach the Weight Top Frame (66) to the Butterfly Top
Frame (33) with two 3/8” x 2 3/4” Bolts (46), a
Support Plate with 4” center holes (94), and two 3/8”
Nylon Locknuts (50). Do not tighten the Nylon
Locknuts yet.
50
66
94
33
50
Attach the Weight Top Frame (66) to the bracket on
the Butterfly Upright (1) with two 3/8” x 2 3/4” Bolts
(46), a Support Plate with 2 1/2” center holes (34),
and two 3/8” Nylon Locknuts (50). Do not tighten the
Nylon Locknuts yet.
15
1
Brackets
46
14. Attach the Weight Top Frame (66) to the Press Top
Frame (9) with one 3/8” x 2 3/4” Bolt (46), a Support
Plate with 4” center holes (94), and a 3/8” Nylon
Locknut (50). Slide a 3 1/2” Pulley (24) with a Cable
Trap (25) onto a 3/8” x 4” Bolt (78). Insert the Bolt
through the Support Plate (94) and hand tighten a
3/8” Nylon Locknut (50) onto it.
14
50
34
66
50
94
9
Attach the Weight Top Frame (66) to the bracket on
the Press Upright (2) with two 3/8” x 2 3/4” Bolts (46),
a Support Plate with 2 1/2” center holes (34) and two
3/8” Nylon Locknuts (50). Do not tighten the Nylon
Locknuts yet.
46
25
24
78
2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Attach each of the four Weight Guides (15) to the
Weight Top Frame (66) with a 3/8” x 3 3/4” Bolt (59),
a 3/8” Flat Washer (48), and a 3/8” Nylon Locknut
(50).
15
16
17
48
50
50
48
Important: Go back and fully tighten all Nylon
Locknuts used in steps 1 through 15.
59
59
15
15
Arm Assembly
16. Locate and open the parts bag labeled “ARM
ASSEMBLY.”
8
Press a Plastic Bushing (100) onto each welded tube
on the Press Frame (8).
6
50
Lubricate
Lubricate the 3/8” x 8” Bolt (52). Attach the Press
Frame (8) to the welded tubes on the Press Base (6)
with the Bolt and a 3/8” Nylon Locknut (50). Do not
overtighten the Nylon Locknut; it must be easy to
pivot the Press Frame.
Welded
Tube
100
52
17. Press a 1 3/4” Square Inner Cap (35) into the top of a
Press Arm (77). Press a 1” Round Inner Cap (76) into
the indicated hole in the Press Arm.
Attach the Press Arm (77) to the bracket on the Press
Frame (8) with two 5/16” x 2 1/2” Bolts (87) and two
5/16” Nylon Locknuts (64).
Repeat this step to assemble the second Press Arm
(77, not shown).
35
76
64
8
87
77
10
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Press a 1 3/4” Square Inner Cap (35) into each end
of the Right Butterfly Arm (11). Wet the lower end of
the Arm with soapy water. Slide a Butterfly Foam Pad
(29) onto the lower end of the Arm.
18
33
Axle
11
Lubricate the indicated axle on the Butterfly Top
Frame (33). Orient the Right Butterfly Arm (11) as
shown and slide it onto the axle. Secure the Butterfly
Arm with two Retainer Rings (31) and a 1” Round
Outer Cap (38). Note: Place the Retainer Rings on
top of the inverted Outer Cap and gently tap the
Cap onto the axle with a hammer. Make sure the
teeth on the Retainer Rings bend towards the Cap
as shown in the inset drawing.
35
31
38
Repeat this step to assemble the Left Butterfly Arm
(10, not shown).
35
29
Axle
31
Teeth
38
19
84
Cable Assembly
Bracket
19. Locate and open the parts bag labeled “CABLE
ASSEMBLY.” For Cable identification and routing
during steps 19 to 49, refer to the Cable Diagrams
and Cable ID Chart on pages 23 and 24.
Identify the Butterfly Cable (73). It is approximately
52” long and it has a closed loop on each end. Attach
the Butterfly Cable to the bracket on the Left Butterfly
Arm (10) with a 3/8” x 1” Bolt (84) and two 3/8” Nylon
Jamnuts (63). Note: The loop on the Cable and the
two Nylon Jamnuts must be mounted underneath
the welded bracket.
63
10
73
20
32
27
20. Locate and open the parts bag labeled “PULLEY
BAG 2.” Remove one “V”-Pulley (27) from the
bag. Leave the remaining pulleys in the bag for
identification of the Pro Pulley.
53
50
Bracket
Wrap the Butterfly Cable (73) around a “V”-Pulley
(27) in the direction shown. Attach the “V”-Pulley and
a Large Cable Trap (32) to the bracket on the back
of the Butterfly Upright (1) with a 3/8” x 2 1/2” Bolt
(53) and a 3/8” Nylon Locknut (50). Make sure the
Large Cable Trap is oriented as shown.
73
1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Remove both 3 1/2” Pulleys (24) from the pre-assem-
bled Small Pulley Bracket (22).
21
22
23
Wrap the Butterfly Cable (73) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley to the
Small Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt
(57) and a 3/8” Nylon Locknut (50). Make sure the
Small Pulley Bracket is oriented exactly as
shown.
73
24
50
22
57
22. Wrap the Butterfly Cable (73) around a “V”-Pulley
(27) in the direction shown. Attach the “V”-Pulley and
a Large Cable Trap (32) to the bracket on the back
of the Butterfly Upright (1) with a 3/8” x 2 1/2” Bolt
(53) and a 3/8” Nylon Locknut (50). Make sure the
Large Cable Trap is oriented as shown.
Bracket
53
73
50
27
32
1
23. Attach the Butterfly Cable (73) to the bracket on the
Right Butterfly Arm (11) with a 3/8” x 1” Bolt (84) and
two 3/8” Nylon Jamnuts (63). Note: The loop on the
Cable and the two Nylon Jamnuts must be mount-
ed underneath the welded bracket.
84
Bracket
63
11
73
24. Identify the Ab Cable (74). It is approximately 224”
long, and it has a ball on one end and a threaded
shaft on the other. You will start by attaching the end
of the Cable with the ball.
24
59
48
47
Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Place two Pulley Covers (47)
over the Pulley, so that the slots in the Pulley Covers
are placed over the Cable. Attach the Pulley and
Pulley Covers to the indicated hole in the Butterfly
Upright (1) with a 3/8” x 3 3/4” Bolt (59), two 3/8” Flat
Washers (48), and a 3/8” Nylon Jamnut (63). Make
sure the Cable is between the Pulley and the
welded pin on the Upright.
Pin
74
24
63
48
1
12
Download from Www.Somanuals.com. All Manuals Search And Download.
25. Remove both 3 1/2” Pulleys (24) from the pre-assem-
bled Adjustable Pulley Plates (23).
25
Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Attach the Pulley and a Cable
Trap (25) to the top hole in the two Adjustable Pulley
Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon
Locknut (50). Make sure the Cable Trap and the
Pulley Plates are oriented as shown.
25
50
24
54
23
74
26. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Attach the Pulley to the Small
Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt (57) and
a 3/8” Nylon Locknut (50). Make sure the Pulley
Bracket is oriented as shown.
26
50
22
57
24
74
27. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Attach the Pulley and a Cable
Trap (25) to the welded bracket on the Butterfly Base
(4) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut
(50). Make sure the Cable Trap is oriented as
shown.
27
74
54
24
25
4
50
13
Download from Www.Somanuals.com. All Manuals Search And Download.
28. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in
the direction shown. Slide the Pulley and a Cable
Trap (25) onto the 3/8” x 3 1/2” Carriage Bolt (95)
already inserted into the Butterfly Base (4). Secure
the Pulley with a 3/8” Nylon Jamnut (63). Make sure
the Cable Trap is oriented as shown.
28
63
74
24
25
24
Route the threaded end of the Ab Cable (74) under
the 3 1/2” Pulley (24) that is already mounted on the
Weight Base (5). Make sure the Cable is routed in
the direction shown.
95
5
4
Note: For clarity, this and the following drawings
show some parts removed.
29. Wrap the Ab Cable (74) around a 4 1/2” Pulley (82) in
the direction shown. Attach the Pulley inside the indi-
cated bracket on the Weight Top Frame (66) with a
3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50).
Make sure the threaded end of the Ab Cable is
routed through the bracket, as shown.
29
50
82
Bracket
57
66
74
End of
Cable
30. Attach the threaded end of the Ab Cable (74) to a “U”-
Bracket (97) with a 1/4” Flat Washer (71) and a 1/4”
Nylon Locknut (68).
30
74
Attach the “U”-Bracket (97) to the hole in the Short
Weight Tube (17) with a 5/16” x 1 3/4” Bolt (96) and a
5/16” Nylon Locknut (64). Note: Do not completely
tighten the Nylon Locknut; it should be threaded
only two turns onto the end of the Cable, as
shown in the inset drawing.
71
68
97
74
97
64
96
17
71
68
14
Download from Www.Somanuals.com. All Manuals Search And Download.
31. Remove a Pro Pulley (26) from the bag labeled
“PULLEY BAG 2.
31
Identify the Low Pulley Cable (75). It is approximately
143 1/2” long and it has a ball on one end and a loop
on the other. Route the end with the loop through the
slot in the cable guide on the Butterfly Base (4).
54
26
25
Route the Low Pulley Cable (75) under a Pro Pulley
(26) as shown. Attach the Pro Pulley and a Cable
Trap (25) to the bracket on the Butterfly Base (4) with
a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
Make sure the Cable Trap is oriented as shown.
4
Cable
Guide
50
1
75
32. Wrap the Low Pulley Cable (75) around a 3 1/2”
Pulley (24) in the direction shown. Attach the Pulley
and a Cable Trap (25) to the indicated hole in the
Butterfly Upright (1) with a 3/8” x 4 3/4” Bolt (60) and
a 3/8” Nylon Jamnut (63). Note: Thread the Jamnut
only two turns onto the Bolt, since you will later
attach another Pulley to the Bolt. Make sure the
Cable Trap is oriented as shown.
32
60
24
25
63
75
33. Wrap the Low Pulley Cable (75) over a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the lower hole in the Adjustable
Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8”
Nylon Locknut (50). Make sure the Cable Trap is
oriented as shown.
33
23
50
54
25
24
75
34. Remove the 3/8” Nylon Jamnut (63) from the
3/8” x 4 3/4” Bolt (60) inserted into the Butterfly
Upright (1) in step 32.
34
1
75
Wrap the Low Pulley Cable (75) around a 3 1/2”
Pulley (24) in the direction shown. Attach the Pulley
and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60)
with the 3/8” Nylon Jamnut (63). Make sure the
Cable Trap is oriented as shown.
25
60
63
24
15
Download from Www.Somanuals.com. All Manuals Search And Download.
35. Attach the loop on the end of the Low Pulley Cable
(75) to the indicated hole in the Small Leg Lever (41)
with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat Washers
(48), and a 3/8” Nylon Jamnut (63).
35
41
63
48
75
48
46
36. Remove a Pro Pulley (26) from the bag labeled
“PULLEY BAG 2.
36
9
Identify the Press Cable (72). It is approximately 389
1/2” long and it has a ball on one end and a threaded
shaft on the other. You will begin by attaching the end
with the ball.
63
48
26
72
Wrap the Press Cable (72) around a Pro Pulley (26) in
the direction shown. Attach the Pulley to the indicated
hole in the Press Top Frame (9) with a 3/8” x 3 1/2”
Bolt (56), a 3/8” Flat Washer (48), and a 3/8” Nylon
Jamnut (63). Make sure the Cable is between the
Pulley and the welded pin on the Press Top Frame.
56
Pin
37. Route the threaded end of the Press Cable (72)
around the 3 1/2” Pulley (24) that is already mounted
on the Top Frame (9).
37
9
24
72
38. Wrap the Press Cable (72) around a 3 1/2” Pulley (24)
in the direction shown. Attach the Pulley to the indicat-
ed hole in the Press Upright (2) with a 3/8” x 3 3/4”
Bolt (59), a 3/8” Flat Washer (48) and a 3/8” Nylon
Locknut (50). Make sure the Cable Trap is oriented
as shown.
38
50
2
48
25
24
72
59
16
Download from Www.Somanuals.com. All Manuals Search And Download.
39. Important: Although the following steps are not
difficult to perform, the correct routing of the
cable is critical to the functioning of the home
gym. Please make sure that you wrap the cable
around the pulleys exactly as shown in each step.
39
40
41
50
24
Route the Press Cable (72) through the opening in
the Press Frame (8), and wrap the Cable around a
3 1/2” Pulley (24) in the direction shown. Route the
end of the Cable back through the opening in the
Press Frame.
72
62
48
8
Attach the Pulley (24) to the indicated hole in the
Press Frame (8) with a 3/8” x 3 1/4” Bolt (62), a 3/8”
Flat Washer (48) and a 3/8” Nylon Locknut (50).
Make sure the Pulley is mounted on the inside of
the Press Frame. Make sure the Cable Trap is ori-
ented as shown.
25
50
48
2
40. Wrap the Press Cable (72) around a “V”-Pulley (27) in
the direction shown. Attach the “V”-Pulley and a Large
Cable Trap (32) to the small tube on the Press
Upright (2) with a 3/8” x 3 1/4” Bolt (62), a 3/8” Flat
Washer (48) and a 3/8” Nylon Locknut (50). Note:
The small tube has four adjustment holes. Mount
the “V”-Pulley in the hole farthest from the
Upright. Make sure the Cable Trap is oriented as
shown.
Small tube,
last hole
32
27
72
62
41. Route the Press Cable (72) back through the opening
in the Press Frame (8) and wrap the Press Cable
around a 3 1/2” Pulley (24) in the direction shown.
Then, route the Press Cable back through the open-
ing in the Press Frame (8).
62
48
Attach the Pulley (24) to the indicated hole in the
Press Frame (8) with a 3/8” x 3 1/4” Bolt (62), a 3/8”
Flat Washer (48), and a 3/8” Nylon Locknut (50).
Make sure the Pulley is mounted on the inside of
the Press Frame. Make sure the Cable Trap is ori-
ented as shown.
72
25
8
24
50
42. Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the indicated hole on the far side
of the Press Upright (2) with a 3/8” x 4 3/4” Bolt (60)
and a 3/8” Nylon Jamnut (63). Note: Thread the
Jamnut only two turns onto the Bolt; you will later
attach another Pulley to the Bolt. Make sure the
Cable Trap is oriented as shown.
42
24
25
60
2
Route the Press Cable (72) back through the opening
in the Press Frame (8), so the end is in front of the
Press Frame.
72
63
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43. Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the indicated hole on the far side
of the Leg Press Lever (83) with a 3/8” x 4 3/4” Bolt
(60) and a 3/8” Nylon Jamnut (63). Note: Thread the
Jamnut only two turns onto the Bolt; you will later
attach another Pulley to the Bolt. Make sure the
Cable Trap is oriented as shown.
43
44
45
72
60
24
25
63
83
44. Wrap the Press Cable (72) around a “V”-Pulley (27)
in the direction shown. Attach the “V”-Pulley and a
Large Cable Trap (32) underneath the Press Seat
Frame (7) with a 3/8” x 4 1/4” Bolt (85), a 3/8” Flat
Washer (48), and a 3/8” Nylon Locknut (50). Note:
the Press Seat Frame has five adjustment holes.
Mount the “V”-Pulley in the hole closest to the
Leg Press Lever. Make sure the Cable Trap is ori-
ented as shown.
7
85
48
32
27
72
50
45. Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the near side of the Leg Press
Lever (83). Use the 3/8” x 4 3/4” Bolt (60) that was
inserted in step 43 and secure the Pulley with the
3/8” Nylon Jamnut (63). Make sure the Cable Trap
is oriented as shown.
83
24
60
25
8
72
63
46. Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to near side of the Press Upright (2).
Use the 3/8” x 4 3/4” Bolt (60) that was inserted in
step 42 and secure the Pulley with the 3/8” Nylon
Jamnut (63). Make sure the Cable Trap is oriented
as shown.
46
50
24
25
2
102
72
Wrap the Press Cable (72) around a 3 1/2” Pulley
(24) in the direction shown. Attach the Pulley and a
Cable Trap (25) to the 3/8” x 4” Carriage Bolt (102)
that was inserted into the Press Base (6) earlier.
Secure the Pulley with the 3/8” Nylon Locknut (50).
Make sure the Cable Trap is oriented as shown.
25
60
63
24
18
Download from Www.Somanuals.com. All Manuals Search And Download.
47. Route the threaded end of the Press Cable (72)
around the 3 1/2” Pulley (24) that was mounted on the
bracket on the Weight Base (5) in an earlier step.
47
48
49
72
24
5
48. Wrap the Press Cable (72) over a 4 1/2” Pulley (82)
in the direction shown. Attach the Pulley inside the
indicated bracket on the Weight Top Frame (66) with
a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut
(50). Make sure the end of the Cable is routed
through the bracket, as shown.
82
50
72
57
66
49. Attach the threaded end of the Press Cable (72) to
the remaining “U”-Bracket (97) with a 1/4” Flat
Washer (71) and a 1/4” Nylon Locknut (68).
72
Attach the “U”-Bracket (97) to the hole in the Long
Weight Tube (70) with a 5/16” x 1 3/4” Bolt (96) and a
5/16” Nylon Locknut (64). Note: Do not completely
tighten the Nylon Locknut; it should be threaded
only two turns onto the end of the Cable, as
shown in the inset drawing.
72
68
97
Important: Follow all four cables from end to end
and make sure that they rest in the grooves of all
pulleys and that the cables and the pulleys move
smoothly.
72
64
97
96
71
68
70
19
Download from Www.Somanuals.com. All Manuals Search And Download.
50
Seat Assembly
50. Locate and open the parts bag labeled “SEAT
ASSEMBLY.”
1
Attach the Backrest (12) to the indicated holes in the
Butterfly Upright (1) with two 1/4” x 2 1/2” Bolts (79)
and two 1/4” Flat Washers (71).
79
12
71
79
51. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the
center hole in a Seat Plate (65). Attach the Seat Plate
to the Press Backrest (99) with two 1/4” x 3/4” Bolts
(49).
51
2
Insert the 1/4” x 2 1/2” Carriage Bolt (45) into the
indicated hole in the Butterfly Upright (2) and secure
it with a 1/4” Flat Washer (71) and a 1/4” Nylon
Locknut (68). Secure the other end of the Press
Backrest (99) with a 1/4” x 2 1/2” Bolt (79) and a 1/4”
Flat Washer (71).
79
68
71
99
49
65
71
45
20
Download from Www.Somanuals.com. All Manuals Search And Download.
52. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the
center hole in a Seat Plate (65). Attach the Seat Plate
to a Seat (13) with two 1/4” x 3/4” Bolts (49).
52
Insert the 1/4” x 2 1/2” Carriage Bolt (45) into the indi-
cated hole in the Butterfly Seat Frame (14) and
secure it with a 1/4” Flat Washer (71) and a 1/4”
Nylon Locknut (68). Secure the other end of the Seat
(13) with a 1/4” x 2 1/2” Bolt (79) and a 1/4” Flat
Washer (71).
45
13
65
14
49
71
79
Attach the other Seat (13) to the Press Seat Frame
(7, not shown) in the same manner.
68
71
53
43
Miscellaneous Assembly
Tube
30
30
53. Press 3/4” Round Inner Caps (43) into the ends of the
Pad Tube (42) and the indicated tube on the Front
Leg (20).
41
43
Insert the Pad Tube (42) into the indicated hole in the
Small Leg Lever (41). Slide Foam Pads (30) onto the
ends of the Pad Tube and the tube on the Leg Lever.
43
30
20
43
42
30
54. Press a 1 3/4” Square Inner Cap (35) into the indicat-
ed end of the Adjustment Tube (90).
54
91
35
90
Attach the Adjustment Tube (90) to the bracket (not
visible in the drawing) on the back of the Leg Press
Plate (55) with a 5/16” x 2 1/2” Bolt (87), two 5/16”
Washers (36), and a 5/16” Nylon Locknut (64).
36
64
87
Attach the Leg Press Plate (55) to the Leg Press
Lever (83) by placing the Adjustment Tube (90) into
the bracket on top of the Leg Press Lever and secur-
ing it with the Lock Pin (91). Note: The lip on the
Leg Press Plate must be on the upper edge.
36
55
83
55. Attach the Curl Pad (105) to the Curl Post (104) with
two 1/4” x 3/4” Bolts (49).
55
105
49
104
21
Download from Www.Somanuals.com. All Manuals Search And Download.
56. Apply the WEIDER PRO 9940 decal in the location shown. Important: The warning decals shown below
have been attached to the home gym in the locations shown. If a decal is missing or illegible, please
call our customer hotline at the number on the front cover of this manual to order a replacement
decal. Apply the new decal in the appropriate location.
56
WEIDER
PRO 9940
57. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
ADJUSTMENT, beginning on page 25 of this manual.
Before using the home gym, pull each cable a few times to make sure that the cables move smoothly over
the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the
cables are not properly installed, they may be damaged when heavy weight is used. If there is any
slack in the cables, you will need to remove the slack by tightening the cables. See TROUBLE-
SHOOTING AND MAINTENANCE on page 26.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Diagrams
The cable diagrams below and on the next page show the proper routing of the Butterfly Cable (73), the Ab
Cable (74), the Low Pulley Cable (75) and the Press Cable (72). The numbers show the correct route for each
Cable. Make sure that the Cables are routed correctly, that the Pulleys move smoothly, and that the
Cable Traps do not touch or bind the Cables. Incorrect cable routing can damage the home gym.
Ab Cable (74)
Low Pulley Cable (75)
7
3
3
1
2
2
1
4
5
8
5
4
Butterfly Cable (73)
6
4
1
5
2
Cable ID Chart
73, 52”
75, 143.5”
74, 224”
72, 389.5”
3
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Press Cable (72)
14
2
1
15
13
5
6
12
9
8
4
3
10
11
7
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustment
The instructions below describe how each part of the home gym can be adjusted. Refer to the exercise poster
accompanying this manual to see how the home gym should be set up for each exercise. IMPORTANT: When
using an attachment, make sure it is in the correct starting position for the exercise to be performed. If
there is any slack in the cables or chain as an exercise is performed, the effectiveness of the exercise
will be reduced.
CHANGING THE WEIGHT SETTINGS
19
To change the setting of the weight stack, insert a Weight
21
Pin (19) under the desired Weight (21). Make sure you
insert the Weight Pin as far as it will go. Note: Due to the
cables and pulleys, the amount of resistance at each
exercise station may vary from the weight setting.
Use the WEIGHT RESISTANCE CHART on page 27 to
find the approximate amount of resistance at each
weight station.
ATTACHING THE LAT BAR, NYLON STRAP OR AB
STRAP TO THE LOW PULLEY STATION
75
58
Attach the Lat Bar (61) to the Low Pulley Cable (75) with
a Cable Clip (69). For some exercises, the Chain (67)
should be attached between the Lat Bar and the Low
Pulley Cable with two Cable Clips. Adjust the length of
the Chain between the Lat Bar and the Low Pulley
Cable so the Lat Bar is in the correct starting position
for the exercise to be performed.
67
69
69
81
61
The Nylon Strap (58) or Ab Strap (81) can be attached in
the same manner.
ATTACHING THE LAT BAR, NYLON STRAP OR AB
STRAP TO THE HIGH PULLEY STATION
69
Attach the Lat Bar (61) to the Press Cable (72) with a
Cable Clip (69). For some exercises, the Chain (67)
should be attached between the Lat Bar and the High
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the High Cable so the
Lat Bar is in the correct starting position for the exer-
cise to be performed.
58
72
67
61
69
81
The Nylon Strap (58) or Ab Strap (81) can be attached in
the same manner.
91
ADJUSTING THE LEG PRESS PLATE
To adjust the position of the Leg Press Plate (55), pull out
the Lock Pin (91) and slide the Adjustment Tube (90)
backwards or forwards in the bracket on the Leg Press
Lever (83). Line up one of the adjustment holes in the
Adjustment Tube with the hole in the bracket and re-insert
the Lock Pin.
90
83
55
25
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the Curl Pad (105), remove the 2” Square Inner
Cap (28) from the Front Leg (20) and insert the Curl Post
(104) into the Front Leg. Secure the Curl Pad by inserting
the Adjustment Knob (103) at the desired height.
105
104
28
103
20
Trouble-shooting and Maintenance
Inspect and tighten all parts each time you use the home gym. Replace any worn parts immediately. The
home gym can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
TIGHTENING THE CABLES
If a cable slips off the pulleys often, the cable may have become twisted. Remove the cable and re-install
it. If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.
The type of cable used on the home gym can stretch slightly when it is first used. If there is slack in the cables
before resistance is felt, the cables should be tightened. Slack can be removed from the cables in several differ-
ent ways:
The Adjustable Pulley Plates (23) have several sets of
adjustment holes. By moving one or both pulleys (24) to
a different set of holes, you will tighten the cables.
23
Adjustment
To move a Pulley (24), remove the 3/8” Nylon Locknut
(50) and the 3/8” x 2” Bolt (54). Remove the Cable Trap
Holes
(25) and Pulley from the Adjustable Pulley Plates (23).
54
50
Re-attach the Pulley and Cable Trap to the appropriate
adjustment hole in the Pulley Plates. Note: Begin by
moving one Pulley to the second adjustment hole. If
the cables are still too loose, move the same Pulley
to the third hole. If additional adjustment is needed,
move the other Pulley until the cables are tight.
25
2
24
Slack can be removed form the Press Cable (72) by
moving one or both of the “V”-Pulleys (27) on the Press
Cable.
One “V”-Pulley (27) is attached to the small tube on the
Press Upright (2). There are three free holes in the small
tube, and you can move the “V”-Pulley to any one of
them to tighten the cables. Start by moving the “V”-
Pulley one hole, and then one more, as needed.
7
27
27
72
The second “V”-Pulley (27) is attached to the Press Seat
Frame (7). There are five adjustment holes in the Seat
Frame. By moving the “V”-Pulley closer to the Press
Upright (2), you will tighten the cables. By moving it fur-
ther away from the Upright, you will loosen the cables.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
The threaded ends on the Press Cable (72) and the Ab
Cable (74) that are attached to the weight stacks can also
be used to tighten the cables.
74
97
64
72
To tighten the Ab Cable (74), remove the “U”-Bracket (97)
from the Short Weight Tube (17) by removing the 5/16” x
1 3/4” Bolt (96) and the 5/16” Nylon Locknut (64).
96
17
71
68
Tighten the 1/4” Nylon Locknut (68) at the end of the Ab
Cable (74) as far as it will go. Then re-attach the “U”-
Bracket (97).
The Press Cable (72) can be tightened the same way.
When you are tightening the cables, take note that they
are linked into two distinct groups. The Butterfly Cable
(73), the Ab Cable (74), and the Low Pulley Cable (75)
are all connected to the small weight stack. All three
cables will be tightened by tightening the Ab Cable (74)
as described above or by using the Adjustable Pulley
Plates (23) as described on the previous page.
The Press Cable (72) is the only cable attached to the
large weight stack. It must be tightened by using the
method described above or by moving the “V”-Pulleys as
described on the previous page.
Weight Resistance Chart
The chart below shows the approximate weight resistance at each exercise station. “Top” refers to the 6 lb. top
weight; the other numbers refer to the 12.5 lb. weight plates. Note: The actual resistance at each station may
vary due to differences in individual weight plates as well as friction between the cables, pulleys, and
weight guides.
High
Pulley
(lbs.)
Arm
Press
(lbs.)
Leg
Press
(lbs.)
Butterfly
(lbs.)
Curl/ Ab Pulley/
Low Pulley Leg Raise
Weight
Plates
(lbs.)
(lbs.)
Top
1
14
28
16
37
21
8
10
24
37
50
64
77
90
8
48
23
38
52
67
82
97
21
35
48
62
76
89
2
42
58
75
3
56
79
101
128
155
181
208
235
262
288
4
69
100
121
142
163
184
205
226
5
83
6
97
7
111
124
138
152
8
9
10
27
Download from Www.Somanuals.com. All Manuals Search And Download.
R0601A
Part Identification Chart–Model No. WESY97310
5/16" Nylon Locknut (64)
3/8" Nylon Jamnut (63)
1/4" Nylon Locknut (68)
3/8" Nylon Locknut (50)
5/16" x 1 3/4" Bolt (96)
5/16" x 2 1/2" Bolt (87)
5/16" x 2 1/2" Carriage Bolt (92)
1/4" Flat Washer (71)
5/16" Washer (36)
5/16" x 2 3/4" Bolt (89)
3/8" x 1" Bolt (84)
1” Tap Screw (80)
3/8" Flat Washer (48)
3/8" x 1 3/4" Bolt (57)
3/8" x 2" Bolt (54)
1/4" x 3/4" Bolt (49)
1/4" x 2 1/2" Bolt (79)
1/4" x 2 1/2" Carriage Bolt (45)
3/8" x 2 1/2" Bolt (53)
3/8" x 2 1/2" Carriage Bolt (101)
Download from Www.Somanuals.com. All Manuals Search And Download.
3/8" x 2 3/4" Bolt (46)
3/8" x 3" Bolt (88)
3/8" x 3 1/4" Bolt (62)
3/8" x 3 1/2" Bolt (56)
3/8" x 3 1/2" Carriage Bolt (95)
3/8" x 3 3/4" Bolt (59)
3/8" x 4" Bolt (78)
3/8" x 4" Carriage Bolt (102)
3/8" x 4 1/4" Bolt (85)
Download from Www.Somanuals.com. All Manuals Search And Download.
3/4" Round Inner Cap (43)
1" Round Inner Cap (86)
1” Retainer Ring (31)
1" Round Inner Cap (76)
1" Square Inner Cap (98)
1" Round Outer Cap (38)
1 3/4" Square Inner Cap (35)
2" Square Inner Cap (28)
Download from Www.Somanuals.com. All Manuals Search And Download.
R0601A
Part List—Model No. WESY97310
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
1
1
1
1
1
2
1
4
2
1
Butterfly Upright
Press Upright
Support Frame
Butterfly Base
Weight Base
Press Base
Press Seat Frame
Press Frame
Press Top Frame
Left Butterfly Arm
Right Butterfly Arm
Backrest
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
#
1
1
6
1
6
3
1
4
15
31
3
1
1
5
3
1
10
1
1
1
1
2
2
1
5
1
1
2
1
2
1
2
5
1
14
1
1
10
4
2
1
2
2
1
1
2
1
1
1
1
1
1
Leg Press Plate
3/8” x 3 1/2” Bolt
3/8” x 1 3/4” Bolt
Nylon Strap
3/8” x 3 3/4” Bolt
3/8” x 4 3/4” Bolt
Lat Bar
3/8” x 3 1/4” Bolt
3/8” Nylon Jamnut
5/16” Nylon Locknut
Seat Plate
Weight Top Frame
Chain
1/4” Nylon Locknut
Cable Clip
Long Weight Tube
1/4” Flat Washer
Press Cable
Butterfly Cable
Ab Cable
Low Pulley Cable
1” Round Inner Cap
Press Arm
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
Seat
Butterfly Seat Frame
Weight Guide
Top Weight
Short Weight Tube
Weight Tube Bumper
Weight Pin
Front Leg
Weight
Small Pulley Bracket
Adjustable Pulley Plate
3 1/2” Pulley
Cable Trap
Pro Pulley
“V”-Pulley
2” Square Inner Cap
Butterfly Foam Pad
Foam Pad
2
2
1
16
1
2
20
16
2
4
13
2
4
4
4
1
2
7
8
2
2
4
1
1
1
4
2
3
10
2
18
8
32
4
1
3/8” x 4” Bolt
1/4” x 2 1/2” Bolt
1” Tap Screw
Ab Strap
4 1/2” Pulley
Leg Press Lever
3/8” x 1” Bolt
3/8” x 4 1/4” Bolt
1” Round Inner Cap
5/16” x 2 1/2” Bolt
3/8” x 3” Bolt
5/16” x 2 3/4” Bolt
Adjustment Tube
Lock Pin
5/16” x 2 1/2” Carriage Bolt
Support Plate, 3 1/2” Center Holes
Support Plate, 4” Center Holes
3/8” x 3 1/2” Carriage Bolt
5/16” x 1 3/4” Bolt
“U”-bracket
1” Square Inner Cap
Press Backrest
Plastic Bushing
3/8” x 2 1/2” Carriage Bolt
3/8” x 4” Carriage Bolt
Adjustment Knob
Curl Post
Curl Pad
User’s Manual
Exercise Poster
Retainer Ring
Large Cable Trap
Butterfly Top Frame
Support Plate, 2 1/2” Center Holes
1 3/4” Square Inner Cap
5/16” Washer
Butterfly Arm Bushing
1” Round Outer Cap
5” Plastic Grip
Bumper
Small Leg Lever
Pad Tube
3/4” Round Inner Cap
Large Bushing
1/4” x 2 1/2” Carriage Bolt
3/8” x 2 3/4” Bolt
Pulley Cover
3/8” Flat Washer
1/4” x 3/4” Bolt
3/8” Nylon Locknut
Weight Bumper
3/8” x 8” Bolt
2
4
3/8” x 2 1/2” Bolt
3/8” x 2” Bolt
#
1
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
R0601A
Exploded Drawing—Model No. WESY97310
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information:
• The MODEL NUMBER of the product (WESY97310)
• The NAME of the product (WEIDER® PRO 9940 home gym)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING
attached at the center of this manual).
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service cen-
ters with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase.
All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to
a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by an ICON authorized service center, products used for commercial or rental pur-
poses, or products used as store display models. No other warranty beyond that specifically set forth
above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
Part No. 176791 R0601A
Printed in Canada © 2001 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|