Model No. 831.150680
Serial No.
Write the serial number in the
space above for future reference.
USER’S MANUAL
Serial Number Decal (Under Seat)
Patent Pending
SEARS, ROEBUCK AND CO.,
HOFFMAN ESTATES, IL 60179
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
10. Always exercise with a partner. Your partner
should be ready to catch the barbell if you
cannot complete a repetition.
11. The weight bench is designed to support a
maximum user weight of 250 pounds. Do not
place more than 310 pounds, including a bar-
bell and weights, on the weight rests. Do not
place more than 150 pounds on the leg lever.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
12. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.
13. When you put weight on the weight rests,
make sure you put at least ten pounds on the
leg lever to balance the weight bench.
5. Make sure all parts are properly tightened
each time you use the weight bench. Replace
any worn parts immediately.
14. Make sure that the adjustment knobs are
inserted completely and tightened into the
uprights before beginning any exercise.
6. Keep children under the age of 12 and pets
away from the weight bench at all times.
15. When adjusting the position of the seat,
make sure that the adjustment pin is inserted
through both adjustment tubes before begin-
ning any exercise.
7. Always wear athletic shoes for foot protec-
tion while exercising.
8. Keep hands and feet away from moving parts.
16. Always remove the curl post from the front
leg before performing leg exercises with the
leg lever.
9. Always be sure there is an equal amount of
weight on each side of your barbell when
you are using it. When adding or removing
weights, always keep some weight on both
ends of the barbell and prevent the barbell
from tipping. Note: The weight bench does
not include a barbell or weights.
17. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. SEARS assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the WEIDER® PRO 875 weight HELPLINE at 1-800-736-6879, Monday through
bench. The versatile WEIDER® PRO 875 is designed
to be used with your own weight set (not included) to
develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic mus-
cle size and strength, or a healthier cardiovascular
system, the WEIDER® PRO 875 will help you to
achieve the specific results you want.
Saturday, 7 a.m. until 7 p.m. Central Time (excluding
holidays). To help us assist you, please note the prod-
uct model number and serial number before calling.
The model number is 831.150680. The serial number
can be found on a decal attached to the weight bench
(see the front cover of this manual).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the WEIDER® PRO 875 weight bench. If you
have additional questions, please call our toll-free
Weight Rests
Upright
Upright
Knob
Curl Pad
Backrest
Storage
Tube
Leg Lever
Weight
Tube
Adjustment
Tubes
Seat
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the part number of the part, from the PART LIST on page 14 of this manual. Important:
Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts
bags, check to see if it has been pre-assembled.
M10 x 81mm Bolt (35)
M10 Washer (41)
M10 x 72mm Bolt (45)
M8 Washer (43)
M6 Washer (40)
M10 x 65mm Bolt (47)
M8 x 58mm Bolt (42)
M
17
B
M6 x 38mm Screw (39)
M10 Nylon Locknut (36)
M8 Nylon Locknut (44)
M6 x 16mm Screw (37)
M4 x 16mm Screw (38)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Make Things Easier for Yourself
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. Most people find that by setting
aside plenty of time, assembly will go smoothly.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• Assembly requires two people.
• One Phillips screwdriver
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
1. Press two 30mm x 60mm Inner Caps (21) into the
base on the Left Upright (4).
1
Align one of the adjustment holes in the left Weight
Rest (6) with the hole in the Left Upright (4).
Tighten an Upright Knob (18) into the holes.
6
Orient the Crossbar (3) and the Left Upright (4) so
the decals are in the positions shown. Attach the
Crossbar to the Left Upright with four M10 x 81mm
Bolts (35), two Joint Plates (14), and four M10
Nylon Locknuts (36). Do not tighten the Nylon
Locknuts yet.
4
3
Warning
Decal
18
36
14
14
Name
Decal
Repeat this step with the Right Upright (not shown).
21
36
35
WARNING:
Always insert the
Upright Knobs (18) through a set of adjust-
ment holes in the Weight Rests (6). Do not
insert the Upright Knobs through the slots in
the Uprights (4, 5).
21
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press three 45mm Square Inner Caps (22) into the
Front Leg (1).
2
22
36
Attach the Front Leg (1) to the Frame (2) with two
M10 x 65mm Bolts (47), a Support Plate (16), and
two M10 Nylon Locknuts (36). Do not tighten the
Nylon Locknuts yet.
2
47
36
1
16
22
22
3. Attach the Frame (2) to the Crossbar (3) with two
M10 x 81mm Bolts (35) and two M10 Nylon
Locknuts (36). Do not tighten the Nylon
Locknuts yet.
3
3
35
36
36
2
4. Press four 1” Square Inner Caps (23) into the
ends of the Right and Left Backrest Frames (7,
8). Press two 1” x 2” Inner Caps (24) into the
adjustment tubes on the Backrest Frames.
4
10
23
Orient the Backrest (10) as shown. Attach the
Backrest to the Right and Left Backrest Frames
(7, 8) with four M6 x 38mm Screws (39) and four
M6 Washers (40). Do not tighten the Screws
yet.
8
40
7
39
23
40
40
39
39
24
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Lubricate the M10 x 178m Bolt (46). Attach the
Right and Left Backrest Frames (7, 8) to the
Frame (2) with the Bolt, two M10 Washers (41),
and an M10 Nylon Locknut (36).
5
Lubricate
Align an adjustment hole in the Right and Left
Backrest Frames (7, 8) with the indicated hole in
the Frame (2). Insert the Backrest Pin (26)
through the Frame and the Backrest Frames, and
secure it with the Spring Clip (25).
46
41
8
7
41
36
Tighten all of the M10 Nylon Locknuts (36)
used in steps 1–3. Tighten the four M6 x
38mm Screws (39) used in step 4.
26
2
25
6. Press three 45mm Square Inner Caps (22) into the
Leg Lever (9). Press a 1” Round Inner Cap (27)
into the indicated end of the Weight Tube (15).
6
36
22
9
Attach the Weight Tube (15) to the Leg Lever (9)
with the M8 x 58mm Bolt (42), two M8 Washers
(43), the Spacer (30), and an M8 Nylon Locknut
(44). Press the 1” Angled Cap (28) onto the back
of the Weight Tube.
28
30
45
22
42
Lubricate
43
43
15
Lubricate an M10 x 72mm Bolt (45). Attach the
Leg Lever (9) to the Front Leg (1) with the Bolt
and an M10 Nylon Locknut (36). Do not over-
tighten the Nylon Locknut; the Leg Lever
must be able to pivot easily.
1
44
22
27
7. Orient the Seat (11) with the wide end on the side
shown. Attach the Seat to the Frame (2) with four
M6 x 16mm Screws (37).
7
11
Wide End
2
37
37
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press two 3/4” Round Inner Caps (29) into each
Pad Tube (19).
8
20
1
Slide two Pad Tubes (19) through the Leg Lever
(9). Slide the third Pad Tube through the holes in
the Front Leg (1).
9
29
Slide two Foam Pads (20) onto the ends of each
Pad Tube (19).
29
19
29
19
20
20
9. Attach the Curl Pad (13) to the Curl Post (12) with
two M6 x 16mm Screws (37).
9
13
37
37
10. Make sure that all parts are properly tightened
before you use the weight bench. The use of
all remaining parts will be explained in ADJUST-
MENTS, beginning on page 10.
12
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 12 for important exercise information
and refer to the accompanying exercise guide to see the correct form for several exercises. Refer also to the
exercise information accompanying your weight set for additional exercises.
Make sure all parts are properly tightened each time you use the weight bench. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (9), slide the desired weights
(not included) onto the Weight Tube (15).
9
To use Olympic weights, press a Weight Adapter
Bushing (34) into each end of the Weight Adapter
(33). Slide the Weight Adapter onto the Weight Tube
(15) and secure it with the Weight Pin (48).
48
33
15
34
WARNING:
Do not place more
than 150 pounds on the Leg Lever (9).
34
ATTACHING THE CURL PAD
For some exercises, the Curl Pad (13) must be
attached to the weight bench.
13
Slide the Curl Post (12) into the Front Leg (1). Align
one of the adjustment holes in the Curl Post with the
adjustment hole in the Front Leg. Tighten the Curl
Post Knob (17) into the adjustment hole in the Front
Leg. Make sure that you fully tighten the Curl Post
Knob.
12
22
17
Note: When the Curl Pad (13) is not in use, the
45mm Square Inner Cap (22) should be inserted
into the Front Leg (1).
1
STORING THE CURL PAD
When the Curl Pad (13) is not in use, it can be stored
in the storage tube on the Left Upright (4).
13
Storage Tube
4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE UPRIGHTS
The Weight Rests (6) can be adjusted to six heights
to accommodate different exercises. To adjust the
height, remove the Upright Knobs (18) from both
Weight Rests and Uprights (4, 5 [not shown]). Slide
the Weight Rests to the desired position and re-insert
the Upright Knobs.
6
WARNING:
Always set both
Weight Rests (6) at the same height. Make
sure that the Upright Knobs (18) are inserted
completely and tightened into the Uprights (4,
5) before you begin any exercise.
4
18
ADJUSTING THE BACKREST
The Backrest (10) can be used in either a decline
position, a level position, or two incline positions. To
adjust the Backrest to the decline position, remove
the Backrest Pin (26) and lower the Backrest until it
rests directly on the Crossbar (3). Re-insert the
Backrest Pin into the adjustment tubes.
10
3
26
To adjust the Backrest (10) to the level position, insert
the Backrest Pin (26) through the top set of holes in
the adjustment tubes and the Frame (2). Secure the
Backrest Pin with the Spring Clip (25).
2
25
To adjust the Backrest (10) to an incline position,
insert the Backrest Pin (26) through one of the lower
two sets of holes in the adjustment tubes and the
Frame (2). Secure the Backrest Pin with the Spring
Clip (25).
Adjustment Tubes
WARNING:
When adjusting the
position of the Backrest (10), make sure that
the Backrest Pin (26) is inserted through both
adjustment tubes and the Frame (2).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
Determining the exact length of time for each workout,
as well as the number of repetitions or sets complet-
ed, is an individual matter. It is important to avoid
overdoing it during the first few months of your exer-
cise program. You should progress at your own pace
and be sensitive to your body’s signals. If you experi-
ence pain or dizziness at any time while exercising,
stop immediately and begin cooling down. Find out
what is wrong before continuing. Remember that ade-
quate rest and a proper diet are important factors in
any exercise program.
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your
muscles will continually adapt and grow as you pro-
gressively increase the intensity of your exercise. You
can adjust the intensity level of an individual exercise
in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
WARMING UP
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is
right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repeti-
tions without difficulty, increase the amount of weight.
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a mod-
erate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise,
and moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on page
13 to find the names of the muscles.
Cross Training
Cross training is an efficient way to get a complete
and well-balanced fitness program. An example of a
balanced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
The combination of weight training and aerobic exer-
cise will reshape and strengthen your body, and
develop your heart and lungs.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The ideal slowly as you stretch and do not bounce. Ease into
resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout is
an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. List the
date, the exercises performed, the weight used, and
the numbers of sets and repetitions completed. Record
your weight and key body measurements at the end of
every month. Remember, the key to achieving the
greatest results is to make exercise a regular and
enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
N
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
A
O
P
B
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
C
Q
D
R
E
S
F
L
T
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
G
M
H
U
I
V
Q. Triceps (back of arm)
W
J
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
K
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. 831.150680
R1101A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
2
1
1
1
1
1
1
1
4
1
1
1
2
3
6
4
6
4
2
1
Front Leg
Frame
Crossbar
Left Upright
Right Upright
Weight Rest
Right Backrest Frame
Left Backrest Frame
Leg Lever
Backrest
Seat
Curl Post
Curl Pad
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
#
1
1
1
6
1
2
2
1
2
10
14
6
4
4
4
2
1
2
1
1
1
2
1
1
1
Backrest Pin
1” Round Inner Cap
1” Angled Cap
3/4” Round Inner Cap
Spacer
50mm Square Bushing
60mm Square Bushing
Weight Adapter
Weight Adapter Bushing
M10 x 81mm Bolt
M10 Nylon Locknut
M6 x 16mm Screw
M4 x 16mm Screw
M6 x 38mm Screw
M6 Washer
M10 Washer
M8 x 58mm Bolt
M8 Washer
M8 Nylon Locknut
M10 x 72mm Bolt
M10 x 178mm Bolt
M10 x 65mm Bolt
Weight Pin
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Joint Plate
Weight Tube
Support Plate
Curl Post Knob
Upright Knob
Pad Tube
Foam Pad
30mm x 60mm Inner Cap
45mm Square Inner Cap
1” Square Inner Cap
1” x 2” Inner Cap
Spring Clip
User’s Manual
Exercise Guide
#
“#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of
this manual for information on ordering replacement parts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. 831.150680
R1101A
23
6
40
10
13
7
8
39
6
37
12
37
23
40
39
32
36
32
38
18
38
40
14
31
38
39
35
24
31
38
14
36
36
18
3
35
4
5
36
21
21
35
36
11
14
26
46
35
36
35
41
36
21
22
17
20
36
36
2
21
25
19
29
36
16
29
9
22
28
47
20
45
22
37
36
1
29
30
42
43
19
20
48
43
29
44
20
22
33
15
29
22
27
29
22
19
34
20
20
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
The model number and serial number of your WEIDER® PRO
Model No. 831.150680
875 are listed on a decal attached to the frame. See the front
cover of this manual to find the location of the decal.
QUESTIONS?
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service
Center. To request service or to order parts by telephone, call
the toll-free numbers listed at the left.
If you find that:
• you need help assembling or
operating the WEIDER® PRO 875
When requesting help or service, or ordering parts, please be
prepared to provide the following information:
• a part is missing
• or you need to schedule repair
service
• The MODEL NUMBER of the product (831.150680)
• The NAME of the product (WEIDER® PRO 875 weight bench)
call our toll-free HELPLINE
• The PART NUMBER and DESCRIPTION of the PART (see the
PART LIST and the EXPLODED DRAWING on pages 14 and
15 of this manual)
1-800-736-6879
Monday–Saturday, 7 am–7 pm
Central Time (excluding holidays)
REPLACEMENT
PARTS
If parts become worn and need to
be replaced, call the following toll-
free number
1-800-FON-PART
(1-800-366-7278)
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS WEIGHT BENCH EXERCISER, contact the nearest SEARS Service Center throughout the United
States and SEARS will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental
purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 180660 R1101A
Printed in China © 2001 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|