PATENT PENDING
USER'S MANUAL
Model No. 831.150460
Serial No.
The serial number can be found in the
location shown below. Write the serial
number in the space above.
Serial Number Decal (under
CAUTION
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the WEIDER® PRO 120
Weight Bench. The PRO 120 Weight Bench is
designed to be used with your own weights (not
included) to develop several muscle groups. Whether
your goal is a shapely figure, dramatic muscle size
HELPLINE at 1-800-736-6879, Monday through
Saturday, 7 a.m. until 7 p.m. Central Time (excluding
holidays). To help us assist you, please note the prod-
uct model number and serial number before calling.
The model number is 831.150460. The serial number
and strength, or a healthier cardiovascular system, the can be found on a decal attached to the PRO 120
PRO 120 Weight Bench will help you to achieve the
specific results you want.
Weight Bench (see the front cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the WEIDER® PRO 120 Weight Bench. If you
have additional questions, please call our toll-free
Backrest
Foam Pads
Lock Pins
Pivot Leg
Foam Pads
Adjustment Leg
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• Place all parts in a cleared area and remove the
packing materials; do not dispose of the packing
materials until assembly is completed.
• During assembly, make sure that all parts are ori-
ented as shown in the drawings.
• Read each assembly step before you begin.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:
• For help identifying the small parts used in
assembly, use the part identification chart
below. The number in parenthesis below each
part refers to the key number of the part. The
second number refers to the quantity needed for
assembly. Note: Some small parts may have
been pre-attached for shipping purposes. If a
part is not in the parts bag, check to see if it
has been pre-attached.
• Two (2) adjustable wrenches
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, or a set of ratchet wrenches.
M6 x 48mm Bolt (4)–2
M10 x 68mm Bolt (14)–1
M6 x 16mm Bolt (5)–2
3/4" Round Inner Cap (7)–4
M10 Nylon Locknut (13)–1
38mm x 38mm Inner Cap (16)–1
38mm x 50mm Inner Cap (8)–1
50mm Round Outer Cap (9)–4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Before beginning assembly, be sure that you
have read and understand the information on
the previous page.
1
8
Press a 38mm x 38mm Inner Cap (16) into the end
of the Frame (1). Press Two 50mm Round Outer
Caps (9) onto the Adjustment Leg (3). Press a
38mm x 50mm Inner Cap (8) into the end of the
Adjustment Leg.
3
Align these
Holes
11
1
Align the indicated holes in the Frame (1) and the
Adjustment Leg (3). Attach the Adjustment Leg to
the Frame with two Lock Pins (11).
16
2
9
2. Align the indicated holes. Attach the Pivot Leg (2) to
the Frame (1) with the M10 x 68mm Bolt (14) and
the M10 Nylon Locknut (13).
1
Align these
Holes
Secure the Pivot Leg (2) by inserting the “L” Pin (15)
through the indicated hole in the Pivot Leg and the
corresponding hole in the Frame (1).
13
15
14
2
Press Two 50mm Round Outer Caps (9) onto the
Pivot Leg (2).
9
3. Press 3/4” Round Inner Caps (7) into the ends of
both Pad Tubes (10).
3
Insert the Pad Tubes (10) through the Adjustment
Leg (3).
6
3
7
10
Slide Foam Pads (6) onto the ends of both Pad
Tubes (10).
7
6
4. Attach the Bench (12) to the Frame (1) with two M6
x 48mm Bolts (4) and two M6 x 16mm Bolts (5).
4
12
1
4
5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE WEIDER PRO 120
The weight bench is designed to be used with your own weights (not included). The steps below explain how the
weight bench can be adjusted. Refer to the accompanying exercise poster for exercise information.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE PIVOT LEG
1
To change the position of the Pivot Leg (2), remove the
15
“L” Pin (15). Align the other set of holes in the Pivot Leg
and the Frame (1). Re-insert the “L” Pin.
2
ADJUSTING THE LEVEL OF THE BENCH
12
To change the level of the Bench (12), remove both
Lock Pins (11) from the Frame (1) and Adjustment Leg
(3). Align the set of holes in the Frame with another set
of holes in the Adjustment Leg. Re-insert the Lock Pins.
Always use both Lock Pins.
1
11
3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST and
EXPLODED DRAWING—Model No. 831.150460
R0996A
Key
No.
Part
No.
Key
No.
Part
No.
Qty.
Description
Qty.
Description
1
2
3
4
5
6
7
8
9
1
1
1
2
2
4
4
2
4
132209 Frame
132504 Pivot Leg
10
11
12
13
14
15
16
#
2
2
1
1
1
1
1
1
1
132148 Pad Tube
132505 Lock Pin
132210 Bench
012033 M10 Nylon Locknut
111084 M10 x 68mm Bolt
105977 “L” Pin
103833 38mm x 38mm Inner Cap
132207 User’s Manual
132506 Adjustment Leg
111855 M6 x 48mm Bolt
132137 M6 x 16mm Bolt
103805 Foam Pad
112402 3/4” Round Inner Cap
132142 38mm x 50mm Inner Cap
100290 50mm Round Outer Cap
#
132208 Exercise Poster
12
1
11
4
8
6
7
13
16
5
10
6
7
2
15
14
7
9
9
6
9
3
9
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The model number and serial number of your WEIDER® PRO 120
are listed on a decal attached to the frame. See the front cover of
this manual to find the location of the decal.
Model No. 831.150460
QUESTIONS?
If you find that:
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
• you need help assembling or
operating the WEIDER® PRO 120
When requesting help or service, or ordering parts, please be pre-
pared to provide the following information:
• a part is missing
• or you need to schedule repair
service
• The MODEL NUMBER of the product (831.150460).
• The NAME of the product (WEIDER® PRO 120).
call our toll-free HELPLINE
1-800-736-6879
Monday–Saturday, 7 am–7 pm
Central Time (excluding holidays)
• The PART NUMBER of the PART (see the PART LIST and the
EXPLODED DRAWING on page 7 of this manual).
• The DESCRIPTION of the PART (see the PART LIST and the
EXPLODED DRAWING on page 7 of this manual).
REPLACEMENT
PARTS
If parts become worn and need to
be replaced, call the following toll-
free number
1-800-FON-PART
(1-800-366-7278)
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS WEIGHT BENCH EXERCISER, contact the nearest SEARS Service Center throughout the
United States and SEARS will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental
purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 132207 R0996A
Printed in China © 1996 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|