Model No. 831.150302
Serial No.
Write the serial number in the
space above for reference.
WEIGHT BENCH EXERCISER
User’s Manual
Serial Number Decal (under seat)
• Assembly
• Adjustments
• Part List and Drawing
Patent Pending
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
11. Always wear athletic shoes for foot protec-
tion while exercising.
12. Do not use a barbell that is longer than
seven feet with the weight bench.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
13. Always make sure there is an equal amount
of weight on each side of your barbell when
you are using it. Always keep some weight
on both ends of the barbell when adding or
removing weights to prevent the barbell from
tipping.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Keep the weight bench indoors, away from
moisture and dust. Do not put the weight
bench in a garage or covered patio, or near
water.
14. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
5. Use the weight bench only on a level surface. 15. Always exercise with a partner. When you
Cover the floor beneath the weight bench to
protect the floor.
are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
6. Make sure all parts are properly tightened
each time the weight bench is used. Replace
any worn parts immediately.
16. Make sure that the adjustment knobs are
inserted completely and tightened into the
uprights before beginning any exercise.
7. Make sure the set screws attaching the
Olympic adapters are properly tightened
each time the adapters are used.
17. When you put weight on the weight rests,
make sure you put at least ten pounds on the
leg lever to balance the weight bench.
8. Keep children under 12 and pets away from
the weight bench at all times.
18. Always remove the curl post from the front
leg before performing leg curls with the leg
lever.
9. Keep hands and feet away from moving parts.
10. The weight bench is designed to support a
maximum user weight of 300 pounds, and a
maximum total weight of 610 pounds. Do not
19. Do not sit on the top end of the backrest;
this will cause the weight bench to tip.
place more than 310 pounds, including a bar- 20. If you feel pain or dizziness at any time while
bell and weights, on the weight rests. Do not
place more than 150 pounds on the leg lever.
Note: The weight bench does not include a
barbell or weights.
exercising, stop immediately and begin cool-
ing down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® PRO
reading this manual, call 1-800-4-MY-HOME®
235 weight bench. The weight bench offers an impres- (1-800-469-4663). To help us assist you, please note
sive array of weight stations designed to develop
every major muscle group of the body. Whether your
goal is to tone your body, build dramatic muscle size
and strength, or improve your cardiovascular system,
the weight bench will help you to achieve the specific
results you want.
the product model number and serial number before
calling. The model number is 831.150302. The serial
number can be found on a decal attached to the
weight bench (see the front cover of this manual for
the location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
ASSEMBLED
DIMENSIONS:
Height: 45 in.
Width: 43 in.
Depth: 71 in.
Weight Rest
Backrest
Upright
Storage Tube
Adjustment
Knob
Curl Pad
Seat
Leg Lever
Backrest
Bracket
Weight Tube
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis by each
part refers to the key number of the part, from the PART LIST on page 14 of this manual. Important: Some
parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags,
check to see if it has been pre-assembled. If a part is missing, call toll-free 1-877-992-5999.
M10 x 76mm Bolt (38)
M10 Nylon Locknut (48)
M10 x 72mm Bolt (43)
M8 Nylon Locknut (29)
M10 x 68mm Bolt (31)
M10 x 65mm Bolt (35)
M10 Washer (46)
1/4" x 10mm
M8 x 58mm Bolt (42)
Set Screw (44)
M8 Washer (47)
M6 x 40mm Bolt (27)
M6 x 16mm Screw (37)
M4 x 16mm Screw (45)
M6 Nylon Locknut (40)
M10 Small
Washer (39)
M6 Washer (36)
25mm Round Angle Cap (34)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight bench can be assembled suc-
cessfully by anyone. However, it is important to
realize that the versatile weight bench has many
parts and that the assembly process will take
time. Most people find that by setting aside plen-
ty of time, assembly will go smoothly.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• One Phillips screwdriver
• Assembly requires two people.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1.
1
Before beginning assembly, make sure you
understand the information in the box
above. For help identifying small parts, use
the PART IDENTIFICATION CHART.
Olympic Width
Hexagon
Holes
43
5
Note: The weight bench can be adjusted to be
used with either a standard barbell or an
Olympic barbell.
46
4
46
39
5
Align the holes in a Crossbar Extension (5) with the
desired set of holes in the Crossbar (4). Secure the
Extension in place with two M10 x 72mm Bolts (43),
four M10 Small Washers (39), two M10 Washers
(46), and two M10 Nylon Locknuts (48). Make sure
the Locknuts and the Small Washers fit inside
the hexagon holes in the Extension. Make sure
the warning decal is in the indicated position.
39
48
Warning
Decal
Standard Width
43
46
4
46
5
Warning
Decal
Repeat this step with the other Crossbar
Extension (5).
39
5
39
48
Hexagon
Holes
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Lift the Weight Rest (9) in the Right Upright (7)
and secure it in a raised position with a Weight
Rest Knob (23).
2
9
Attach the Right Upright (7) to the right Crossbar
Extension (5) with four M10 x 76mm Bolts (38),
two Joint Plates (18), and four M10 Nylon
23
Locknuts (48). Do not tighten the Locknuts yet.
7
Repeat this step with the Left Upright (not
shown).
48
18
48
18
5
38
38
3. Attach the Front Leg (2) to the Bench Frame (1)
with two M10 x 65mm Bolts (35), two M10
Washers (46), and two M10 Nylon Locknuts (48).
Do not tighten the Locknuts yet.
3
35
2
1
46
48
46
35
4. Attach the Bench Frame (1) to the center holes in
the Crossbar (4) with two M10 x 72mm Bolts (43)
and two M10 Nylon Locknuts (48).
4
Tighten the M10 Nylon Locknuts (48) used in
steps 1–4.
Center
Holes
4
48
43
1
43
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Attach the Weight Tube (16) to the Leg Lever (3)
with an M8 x 58mm Bolt (42), two M8 Washers
(47), a 10mm Spacer (30), and an M8 Nylon
Locknut (29). Press a 25mm Round Angled Cap
(34) onto the end of the Weight Tube.
5
48
3
2
31
Lubricate
Lubricate an M10 x 68mm Bolt (31) with grease.
Attach the Leg Lever (3) to the Front Leg (2) with
the Bolt and an M10 Nylon Locknut (48). Do not
overtighten the Locknut; the Leg Lever must
be able to pivot easily.
30
34
47
29
47
42
16
6. Attach the Backrest Tubes (12) to the Backrest
Bracket (10) with four M6 x 40mm Bolts (27), four
M6 Washers (36), and four M6 Nylon Locknuts
(40). Do not tighten the Locknuts yet.
6
27
12
36
36
36
36
27
40
40
10
7. Insert the Backrest Bracket (10) into the slot in
the Bench Frame (1).
7
Lubricate an M10 x 168mm Bolt (41) with grease.
Attach the Backrest Tubes (12) to the Bench
Frame (1) with the Bolt and an M10 Nylon Locknut
(48). Do not overtighten the Locknut; the
Backrest Tubes must be able to pivot easily.
12
48
Lubricate
41
1
10
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Orient the Backrest (13) as shown. Attach the
Backrest to the Backrest Tubes (12) with four M6
x 40mm Bolts (27) and four M6 Washers (36).
8
13
Attach the tether on the Adjustment Pin (25) to
the Bench Frame (1) with an M4 x 16mm Screw
(45). Insert the Pin through the Bench Frame and
the Backrest Bracket (10).
Wide
End
12
Tighten the four M6 Nylon Locknuts (40) used
in step 6.
36
27
36
25
36
10
45
27
36
1
27
9. Orient the Seat (14) as shown. Attach the Seat to
the Bench Frame (1) with four M6 x 16mm
Screws (37).
9
14
Wide
End
1
37
37
10. Slide a Pad Tube (19) into the square hole in the
Front Leg (2). Slide two Foam Pads (20) onto the
Pad Tube. Make sure the Foam Pads are ori-
ented as shown.
10
3
20
2
Repeat this step with the other two Pad Tubes
(19) and the Leg Lever (3).
19
20
19
19
11. Attach the Curl Pad (15) to the Curl Post (11) with
two M6 x 16mm Screws (37).
11
15
11
12. Make sure that all parts are properly tightened
before you use the weight bench. The use of
all remaining parts will be explained in ADJUST-
MENTS, beginning on the following page.
37
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 12 for important exercise information
and see the accompanying exercise guide to see the correct form for each exercise. Refer also to the
exercise information accompanying your weight set for additional exercises.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
The Backrest (13) can be used in a decline position,
a level position, or an incline position. To use the
Backrest in the decline position, remove the
Adjustment Pin (25) and lay the Backrest on the
Crossbar (4).
13
To use the Backrest (13) in the level position, lift the
Backrest and insert the Adjustment Pin (25) through
the Bench Frame (1) and the top hole in the Backrest
Bracket (10).
4
To use the Backrest (13) in an incline position, lift the
Backrest and insert the Adjustment Pin (25) through
the Bench Frame (1) and a lower hole in the Backrest
Bracket (10).
1
25
10
3
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (3), slide the desired weights
(not included) onto the Weight Tube (16).
WARNING:
Do not place more than
150 pounds on the Leg Lever (3).
16
Weights can be stored on the tubes on the Uprights
(not shown).
Weight
ADJUSTING THE WEIGHT RESTS
To change the height of the Weight Rests (9), remove
the Weight Rest Knobs (23). Position the Weight
Rests to the desired height in the Uprights (8, 7 [not
shown]) and secure them with the Weight Rest Knobs.
9
WARNING:
Always set both Weight
Rests (9) at the same height. Make sure the
Weight Rest Knobs (23) are inserted into both
the Upright (7 or 8) and the Weight Rest.
23
8
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE BENCH WIDTH
To adjust the width of the bench to use either a stan-
dard barbell or an Olympic barbell, remove the indi-
cated M10 x 72mm Bolts (43) from the Crossbar
Extensions (5).
5
43
See assembly step 1 for instructions on how to
reassemble the Crossbar (4) at the desired width.
5
4
43
ATTACHING THE CURL POST
For some exercises, the Curl Post (11) must be
attached to the weight bench. Remove the 45mm
Square Inner Cap (26) from the Front Leg (2).
Slide the Curl Post (11) into the Front Leg (2). Align
one of the adjustment holes in the Curl Post with the
adjustment hole in the Front Leg. Tighten the Curl
Post Knob (24) into the adjustment hole in the Front
Leg. Make sure that you fully tighten the Knob.
24
11
26
Note: When the Curl Post (11) is not in use, the
45mm Square Inner Cap (26) should be inserted
into the Front Leg (2).
2
OLYMPIC WEIGHT ADAPTER
Press a 48mm Round Inner Cap (32) into the Olympic
Adapter (17). Attach the Olympic Adapter to the
Weight Tube (16) with an 1/4" x 10mm Set Screw
(44). Make sure the Set Screw is on the bottom of
the Adapter.
17
32
16
44
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
To increase the size and strength of your muscles,
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-
cles will continually adapt and grow as you progres-
sively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
ing it during the first few months of your exercise pro-
gram. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immedi-
ately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise pro-
gram.
WARMING UP
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
right for you. Begin with 3 sets of 8 repetitions for each your body for more strenuous exercise by increasing
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a mod- Each workout should include 6 to 10 different exercis-
erate percentage of their capacity. Select a moderate
amount of resistance and increase the number of rep-
etitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by com-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
pleting more sets rather than by using high amounts of Schedule your workouts for the time of day when your
resistance.
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
Cross Training
Cross training is an efficient way to get a complete and moving only the appropriate parts of the body.
well-balanced fitness program. An example of a bal-
anced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an elliptical or
exercise bike, on Tuesday and Thursday.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. See the muscle chart on the next
page to find the names of the muscles.
• Rest from both strength training and aerobic exercise The repetitions in each set should be performed
for at least one full day each week to give your body
time to regenerate.
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
The combination of strength training and aerobic exer-
cise will reshape and strengthen your body, plus devel- during the return stroke. Never hold your breath.
op your heart and lungs.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. List the
date, the exercises performed, the resistance used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month. Remember, the key to achiev-
ing the greatest results is to make exercise a regular
and enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A. Sternomastoid (neck)
A
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
P
L
B
Q
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
C
D
E
R
S
T
F
M
N
U
G
H
I
V
W
X
J
K
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. 831.150302
R1104A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
2
2
1
1
2
1
1
2
1
1
1
1
1
4
3
6
2
4
2
1
1
6
8
Bench Frame
Front Leg
Leg Lever
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
#
4
1
1
1
1
3
1
2
8
6
8
8
4
1
1
6
1
9
6
2
18
6
1
1
1
1
25mm Square Inner Cap
M8 Nylon Locknut
10mm Spacer
M10 x 68mm Bolt
48mm Round Inner Cap
25mm Round Inner Cap
25mm Round Angled Cap
M10 x 65mm Bolt
M6 Washer
M6 x 16mm Screw
M10 x 76mm Bolt
M10 Small Washer
M6 Nylon Locknut
M10 x 168mm Bolt
M8 x 58mm Bolt
M10 x 72mm Bolt
1/4" x 10mm Set Screw
M4 x 16mm Screw
M10 Washer
Crossbar
Crossbar Extension
Crossbar Cap
Right Upright
Left Upright
Weight Rest
Backrest Bracket
Curl Post
Backrest Tube
Backrest
Seat
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Curl Pad
Weight Tube
Olympic Adapter
Joint Plate
Pad Tube
Foam Pad
Weight Rest Cap
Square Bushing
Weight Rest Knob
Curl Post Knob
Adjustment Pin
45mm Square Inner Cap
M6 x 40mm Bolt
M8 Washer
M10 Nylon Locknut
19mm Square Inner Cap
User’s Manual
Exercise Guide
Allen Wrench
#
#
#
Grease Pack
Note: “#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts. If a part is missing, call toll-free 1-877-992-5999.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. 831.150302
R1104A
13
28
9
45
27
12
45
12
15
48
21
22
23
36
36
27
36
36
36
27
28
36
27
33
7
41
11
48
46
9
37
18
40
5
18
43
46
10
40
45
45
45
39
48
22
4
39
6
6
45
38
21
22
14
45
43
22
39
48
46
48
23
43
39
46
45
48
43
25
5
18
35
24
48
38
26
33
1
48
45
18
20
8
46
49
26
37
30
20
48
26
31
19
3
35
2
20
49
46
20
26
49
34
29
47
19
26
33
44
47
49
16
42
20
17
32
26
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FULL 90-DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
WEIGHT BENCH EXERCISER, contact the nearest Sears Service Center throughout the United States
and Sears will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for
rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL 60179
Part No. 221116 R1104A
Printed in China © 2004 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|