R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
PE550
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
WEED EATER
1030 Stevens Creek Road
Augusta, GA 30907
545186731 Rev. 4 3/15/09 BRW
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING:
Blade can throw objects violently.
D You can be blinded or injured.
D Wears safety glasses or similar eye
protection.
Safety
Glasses
Boots
WARNING:
Hazard zone for thrown objects.
D Blade can throw objects violently.
D Others can be blinded or injured.
D Keep people and animals 50 feet (15 meters)
away.
Blade rotates
momentarily
after the
Allow blade to stop
before removing
it from the cut.
WARNING:
Blade rotates momentarily after the trigger is
released.
trigger is
released.
D The blade can seriously cut you or others.
D Allow blade to stop before removing it from
the cut.
WARNING:
Read instruction manual.
D Follow all warnings and instructions.
D Failure to do so can result in serious
injury.
Safety Labels
Instruction Manual
S Store unit andfuelin area where fuelvapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
FUEL SAFETY
S Mix and pour fuel outdoors and where there
are not sparks or flames.
S Always store gasoline in a container ap-
proved for flammable liquids.
S Store unit so blade cannot accidentally
cause injury.
S Do not smoke or allow smoking near fuel or
the unit; do not smoke while using the unit.
S Make sure the unit is properly assembled
and in good operating condition.
S Store unit out of reach of children.
If situations occur which are not covered in this
manual, use care and good judgment. If you
need assistance, call 1-800-554-6723.
S Avoid spilling fuel or oil. Wipe up all fuel
spills before starting unit.
WARNING: Theengine exhaust from
this product contains chemicals known to the
State of California to cause cancer, birth de-
fects or other reproductive harm.
S Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S Stop engine and allow to cool before re-
moving fuel cap.
S Do not store the unit with fuel in the fuel
tank; use up fuel left in the carburetor and
fuel line by starting the unit and letting it run
until it stops.
SPECIAL NOTICE:
This unit is not
equipped with a temperature limiting muffler
and spark arresting screen which meets the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines be
equipped with a spark arrestor screen. If you
operatein alocalewhere such regulations ex-
ist, you are legally responsible for installing
and maintaining the operating condition of
these parts. Failure to do so is a violation of
the law. If a spark arresting screen is re-
quired in your area, contact your authorized
service dealer for the correct kit.
S Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
TRANSPORTING AND STORAGE
S Do not grasp or hold exposed blade.
S Stop unit before leaving work area.
S Allow unit to cool, run fuel out of the fuel
tank, and secure the unit before storing or
transporting it in a vehicle.
S Before storing, use up fuel left in the carbu-
retor by starting the unit and lettingit run un-
til it stops. Always allow the unit to cool be-
fore storage.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti-vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swellings. Prolonged use in cold
weather has beenlinked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
SAVE THESE INSTRUCTIONS
ASSEMBLY
3. Thread one locknut onto each screw and
tighten securely.
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
Handle tube
Screws
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554--6723.
This instruction manual has been developed
to help you assemble the unit and to provide
its safe operation. It is important that you read
the entire manual to become familiar with the
unit before you begin assembly.
Read your instruction manual.
Tools you will need:
S Adjustable wrench
S Hex wrench (provided)
TUBE ASSEMBLY
NOTE: When performing the following step,
be sure the handle is aligned as follows: label
on top, throttle trigger to the operator’s right
hand side. The starter rope and the throttle
cable must not wrap around the tube.
Lower
Tube
Starter Rope
Locknuts
NOTE: When performing the following step,
be sure the starter rope is not caught under
the cable clamp. The starter rope must hang
freely to operate properly.
4. Align the cable clamp between the tube
screws. Install the cableclamp aroundthe
tube and throttle cable.
Label
Throttle trigger
Cable Clamp
1. Assemble handle tube to the lower tube (it
will be necessary to pull some of the start-
er rope out of the housing).
2. Align the screw holes; insert the screws
through the aligned holes.
Throttle cable
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR EDGER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the vari-
ous controls and adjustments. Save this manual for future reference.
Starter Rope Handle
ON/OFF
Fuel/Oil Mix Cap
Switch
Throttle Trigger
Choke
Depth
Control
Lever
Spark Plug
Air Filter
Primer Bulb
Muffler and
Depth
Guard
Blade Guard
Adjusting
Skid
Blade
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
ON/OFF SWITCH
The ON/OFF switch is used to select the ON
or OFF position.
STARTER ROPE HANDLE
The STARTER ROPE HANDLE is used for
starting the engine.
THROTTLE TRIGGER
The THROTTLE TRIGGER controls engine
speed. It is designed to be activated by the
right hand.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer bulb
by pressing it and allowing it to return to its origi-
nal form.
BLADE
The BLADE is designed to cut sod.
DEPTH ADJUSTING SKID
The DEPTH ADJUSTING SKID sets the
depth of the cut.
CHOKE
DEPTH CONTROL LEVER
The DEPTH CONTROL LEVER regulates
the cutting depth. Move the lever backward
for full depth edging, forward for half depth
edging.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
of 40:1. Poulan/WEED EATER brand synthetic
oil is recommended. Mix gasoline and oil at a ra-
tio of 40:1. A 40:1 ratio is obtained by mixing 3.2
fluid ounces (95 ml) of oil with 1 gallon (4 liters)
of unleaded gasoline. DO NOT USE automotive
oil or boat oil. These oils will cause engine dam-
age. When mixing fuel, follow instructions
printed on container. Once oil is added to gaso-
line, shake container momentarily to assure that
the fuel is thoroughly mixed. Always read and
follow the safety rules relating to fuel before fuel-
ing your unit.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
CAUTION: Never use straight gasoline in
your unit. This will cause permanent engine
damage and void the limited warranty.
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2-cycle synthetic oil into
one gallon of fresh gas.
FUEL REQUIREMENTS
This engine requires the use of minimum 87
octane [R+M]/2 clean gasoline.
IMPORTANT
This engine is certified tooperate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle air-
cooled engine oil designed to be mixed at a ratio
Use of alcohol blended fuels (called gasohol or
using ethanol or methanol) can cause major en-
gine performance and durability problems.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Choke Lever
WARNING: Alternative fuels (not gas-
oline) such as E--15 (15% alcohol), E--20 (20%
alcohol), E--85 (85% alcohol) are NOT classified
as gasoline and are NOT approved for use in
2--stroke gasoline engines. Use of alternative
fuels will cause problems such as: improper
clutch engagements, overheating, vapor lock,
power loss, lubrication deficiency, deterioration
of fuel lines, gaskets and internal carburetor
components, etc. Alternative fuels cause high
moisture absorption into the fuel/oil mixture
leading to oil and fuel separation.
FULL
HALF
OFF
STOPPING YOUR ENGINE
S To stop a running engine, move the switch
to the OFF position.
S If engine does not stop, move choke lever
to FULL CHOKE position.
Primer bulb
ON/OFF Switch
4. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
5. Pull starter rope handle sharply until en-
gine sounds as if it is trying to start, but do
not pull rope more than 6 times.
STARTING YOUR ENGINE
6. As soon as engine sounds as if it is trying
to start, move choke lever to the HALF
CHOKE position.
(for location of controls, refer to the KNOW
YOUR EDGER section)
S Fuel the engine; then move 10 feet (3 me-
ters) away from the fueling site.
7. Pull starter rope sharply until engine runs,
but no more than 6 pulls. If the engine
doesn’t start after 6 pulls (at the HALF
CHOKE position), move the choke lever to
the FULL CHOKE position and press the
primer bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more than
6 pulls. NOTE: If engine still doesn’t start, it
is probably flooded. Proceed to STARTING
A FLOODED ENGINE.
DANGER: The cutting blade will
turn when the engine starts.
WARNING: Avoid any contact with
the muffler. A hot muffler can cause serious
burns.
S Rest the unit on the ground. Support the
unit so the blade is off of the ground and
away from trees, bushes, onlookers, etc.
8. Once the engine starts, allow it to run 10 se-
conds, then move the choke lever to OFF
CHOKE. Allow the unit to run for 30 more
seconds at OFF CHOKE before releasing
the throttle trigger. NOTE: If engine dies
with the choke lever in the OFF CHOKE
position, move the choke lever to the HALF
CHOKE position and pull the rope until en-
gine runs, but no more than 6 pulls.
STARTING
POSITION
STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1-800-554 -6723.
2. Move the choke lever to the HALF
CHOKE position.
3. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
4. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
5. Allow engine to run 10 seconds, then
move the choke lever to the OFF CHOKE
position. Release the throttle trigger.
1. Move the ON/OFF switch to the ON posi-
tion.
NOTE: If engine has not started, pull starter
rope 5more pulls. If engine still does not run, it
is probably flooded. Proceedto STARTING A
FLOODED ENGINE.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could requirepulling thestarter
handle many times depending on how badly
the unit is flooded.
SETTING THE EDGING DEPTH
WARNING: Never attempt to adjust
the depth adjusting skid when the engine is
running. Always release the throttle trigger,
wait until the blade stops turning, move the
ON/OFF switch to the OFF position, and dis-
connect spark plug before making adjust-
ments. Your edger is equipped with several
edging depths. The depth used will depend
on your personal edging preference and the
condition of the area where the edging opera-
tion is to be done.
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
OPERATING INSTRUCTIONS
EDGING
As you become familiar with your edger, you
will be able to determine your own operating
pace. Conditions such as depth of cut and
material being cut will regulate the speed and
time required for your edging job.
NOTE: If the area to be edged has never
been cut or several weeks have passedsince
the last cut, the first edging should be done at
no more than half depth.
To set the depth:
S Allow the engine to warm up for one minute
before you begin edging.
S Move the depth control lever forward for
shallower edging.
S Increase the engine speed before placing
the blade in the cut. For best operation, run
the engine at full throttle while cutting.
S Keep your edging path straight by aligning
the blade guide rib on the rear of the blade
guard with the edge of the sidewalk. Keep
all wheels flat on the walkway.
S Move the depth control lever backward for
deeper edging.
Depth Control Lever
Depth
Adjusting
Skid
Blade
Guide Rib
Support Arm
When edging, the trigger handle must be
raised until the skid rests on the ground. The
trigger handle must be held in the raised posi-
tion during the entire edging operation to
maintain a consistent edging depth.
DEPTH ADJUSTING SKID
S Always work going away from people and
solid objects such as walls, large stones,
trees, automobiles, etc.
S Be careful when edging near trees or valu-
able plants. The high speed metal blade
may cut roots and cause damage to the
plants.
S If the blade stalls, immediately move the
unit rearward slightly to allow the blade to
restart. If the blade continues to stall, stop
the engine, disconnect the spark plug, and
inspect for blockage or damage.
S Always keepthe bladearea clean. Stop the
engine, make sure the blade has complete-
ly stopped turning, and disconnect the
spark plug before cleaning.
The surface of the depth adjusting skid will
wear over aperiod of time. This part is revers-
ible to provide a second wear surface.
1. Remove the two mounting screws which
hold the skid to the support arm.
2. Rotate the skid 180 degrees.
3. Reinstall the mounting screws.
EDGING TIPS
S Inspect unit before each use.
S Inspect the area to be cut before each use.
S Keep unit in front of your body.
S Cut at full throttle.
S Keep the wheels and skid in contact with
the ground.
S Always work going away from others.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Always clean your air filter after 5 tanks of fuel
or 5 hours of operation, whichever comes
first. Clean more frequently in dusty condi-
tions. It is advisable to replace your air filter
with a new one after every 50 hours of opera-
tion, or annually, whichever comes first.
To clean filter:
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove the two screws and the air filter
cover from the engine.
ommended maintenance
described in the instruction
manual performed by an
authorized service dealer.
3. Remove air filter.
If any dealer other than an authorized
service dealer performs work on the
product, WEED EATER may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
NOTE: Do not clean the air filter with gaso-
line or other flammable solvent to avoid creat-
ing a fire hazard or producing harmful evapo-
rative emissions.
4. Clean the air filter using hot soapy water.
Rinse with clean cool water. Air dry com-
pletely before reinstalling.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
S Once each year, replace the spark plug, re-
place air filter element and check blade for
wear. A new spark plug and a clean/new air
filter element assures proper air/fuel mix-
ture and helps your engine run better and
last longer.
5. Lightly oil air filter before installing to im-
prove the efficiency of the air filter. Use
2--cycle engine oil or motor oil (SAE 30).
NOTE: Do not soak air filter in oil.
6. Squeeze the air filter to distribute oil and to
remove any excess oil.
7. Reinstall air filter in housing.
CAUTION: Make sure air filter is fitted in to
the corners of the housing to prevent air from
bypassing the filter and to keep dust from en-
tering engine and causing damage.
8. Reinstall air filter cover.
CHECK FOR DAMAGED OR
WORN PARTS
Air Filter
Cover
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/OFF Switch -- Ensure ON/OFF switch
functions properly by moving the switch to
the OFF position and assure the engine
stops; then restart engine and continue.
S Fuel Tank -- Discontinue use of edger if fuel
tank shows signs of damage or leaks.
S Blade Guard -- Discontinue use of edger if
blade guard is damaged.
Cover
Screws
BLADE MAINTENANCE
WARNING: The blade will continue
to spin after the engine stops or after the
throttle trigger has been released. Make sure
the blade has stopped coasting and discon-
nect the spark plugbefore performing work on
the blade.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Blade nut
S Muffler
S Cylinder shield
S Clutch
S Throttle trigger
S Handle screws
S Fasteners
WARNING: Wear protective gloves
when handling or performing maintenance on
the blade to help avoid injury.
Always replace a blade that is bent, warped,
cracked, broken, or damaged in any other
way. Never attempt to straighten and reuse a
damaged blade. Use only specified replace-
ment blade.
S The blade is reversible. When the cutting
edge on one side becomes worn, turn the
blade over.
S Check blade for flatness periodically. Lay
the blade on a flat surface to inspect for flat-
ness. Throw away a blade that is not flat.
INSPECT AND CLEAN UNIT & LA-
BELS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases the life and perfor-
mance of the engine and increases fuel con-
sumption and harmful emissions.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACE SPARK PLUG
Spark Plug Boot
The spark plug should be replaced each year
to ensure the engine starts easier and runs
better. Set spark plug gap at 0.025 inches.
Ignition timing is fixed, nonadjustable.
1. Twist then pull off the spark plug boot.
2. Remove and discard the spark plug.
3. Replace with Champion RCJ--6Y spark
plug and tighten securely with a wrench.
4. Reinstall the spark plug boot.
Spark Plug
SERVICE AND ADJUSTMENTS
S Engine will not idle when the throttle is re-
BLADE REPLACEMENT
leased.
1. To remove the blade, insert a screwdriver
into one of the holes in the gearbox; then,
remove the blade nut by turning clockwise.
S The blade spins at idle.
Keep others away when making idle speed
adjustments. Remove the blade before mak-
ing carburetor idle speed adjustments. Donot
make adjustments from the blade side of the
unit. Recheck the idle speed after each ad-
justment. The blade must not spin at idle
speed to avoid serious injury to the operator
or others. Make adjustments with the unit
supported so the blade is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the blade and muffler.
Gearbox holes
To adjust idle speed:
Allow engine to idle. Adjust speed until engine
runs without the blade shaft spinning (idle too
fast) or engine stalling (idle speed too slow).
S Turn idle speed screw clockwise to in-
crease enginespeed if enginestalls or dies.
S Turn idle speed screw counterclockwise to
decrease engine speed if the blade shaft
spins at idle speed.
Blade
2. Remove the washer and blade from the
blade shaft.
3. Align the flat areaof the blade opening with
the flat side of the shaft. Place the new
blade on the shaft.
WARNING: Recheck the idle speed
after each adjustment. The blade shaft must
not spin at idle speedto avoid serious injury to
the operator or others.
Nut
Hole
TO REMOVE
Flat sides
Washer
4. Install the washer and nut; turn nut coun-
terclockwise on the blade shaft.
5. Bind blade by inserting a screwdriver into
one of the holes in the gearbox; then, firmly
tighten nut with a wrench.
CARBURETOR IDLE SPEED
ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The blade
shaft will be spinning during most of this pro-
cedure. Wear your protective equipment and
observe all safety precautions. After making
adjustments, the blade shaft must not spin at
idle speed.
The carburetor has been carefully set at the
factory. Adjustments may benecessary if you
notice any of the following conditions:
Idle Speed
Adjustment
Screw
If you require further assistanceor are unsure
about performing this procedure, contact an
authorized
service
dealer
or
call
1--800--554--6723.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
HELPFUL TIP
WARNING: Perform the following
During storage of your gas/
oil mixture, the oil will sepa-
rate from the gas.
steps after each use:
S Allow engine to cool before storing or trans-
porting.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy stor-
age.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performingall of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start or will run
only a few
seconds after
starting.
1.ON/OFF switch in OFF 1. Move ON/OFF switch to the ON
position.
position.
2. Engine flooded.
2. See “Difficult Starting” in
Operation Section.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6.Compression low.
5. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
1. See “Carburetor Idle Speed Adjustment”
in Service and Adjustments Section.
2. Crankshaft seals worn. 2. Contact an authorized service dealer.
3. Compression low.
3. Contact an authorized service dealer.
Engine will not
accelerate,
lacks power,
or dies under
a load.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build up.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
1. Adjust choke.
smokes
2. Fuel mixture incorrect. 2. Empty fuel tank and refill with
correct fuel mixture.
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs
hot.
1. Fuel mixture incorrect. 1. See “Fueling Engine” in Operation
section.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
2. Replace with correct plug.
3. Contact an authorized service dealer.
4. Carbon build-up.
4. Contact an authorized service dealer.
Blade turns at
idle speed.
1. Carburetor requires
1. See “Carburetor Adjustment” in
adjustment.
Service and Adjustments Section.
2. Throttle cable binding. 2. Replace or repair throttle cable.
3. Clutch requires repair. 3. Contact an authorized service dealer.
1. Check gearbox.
Blade stops un-
der a load or
does not turn
when engine is
accelerated.
1. Blade not engaged.
2. Contact an authorized service dealer.
2. Carburetor requires
adjustment.
3. Contact an authorized service dealer.
3. Clutch requires repair.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WEED EATER, a division of Husqvarna Con-
In Canada, contact:
sumer Outdoor Products N.A., Inc., warrants
to the original consumer purchaser that each
new WEED EATER brand gasoline tool or at-
tachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the orig-
inal date of purchase.
WEED EATER
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTH-
ER RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIM-
ITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson-Moss Act
of 1975.
The policy of WEED EATER is to continuous-
ly improve its products. Therefore, WEED
EATER reserves the right to change, modify,
or discontinue models, designs, specifica-
tions, and accessories of all products at any
time without notice or obligation to any pur-
chaser.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by WEED EATER
for this tool. This warranty does not cover
tune-up, spark plugs, filters, starter ropes, or
blades that will wear and require replacement
with reasonable use during the warranty peri-
od. This warranty does not cover pre-delivery
setup or normal adjustments explained in the in-
struction manual. This warranty does not cover
transportation costs.
In the event you have a claim under this warran-
ty, you must return the product to an authorized
service dealer.
Should you have any unanswered questions
concerning this warranty, please contact:
WEED EATER, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
1030 Stevens Creek Road
Augusta, GA 30907
1--800--554--6723
U.S. EPA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency, Environment Canada and
WEED EATER are pleased to explain the
emissions control system warranty on your
year 2009 and later small off--road engine.
WEED EATER must warrant the emission
control system on your small off--road engine
for the periods of time listed below provided
there has been no abuse, neglect, or improp-
er maintenance of your small off--roadengine.
Your emission control system includes parts
such as the carburetor, the ignition system
and the fuel tank. Where a warrantable condi-
tion exists, WEED EATER will repair your
small off--road engine at no cost to you. Ex-
penses covered under warranty include diag-
nosis, parts and labor. MANUFACTURER’S
WARRANTY COVERAGE: If any emissions
related part on your engine (as listed under
Emissions Control Warranty Parts List) is de-
fective or a defect in the materials or work-
manship of the engine causes the failure of
such an emission related part, the part will be
repaired or replaced by WEED EATER.
OWNER’S WARRANTY RESPONSIBILI-
TIES: As the small off--road engine owner,
you are responsible for the performance of
the required maintenance listed in your in-
struction manual. WEED EATER recom-
mends that you retain all receipts covering
maintenance on your small off--road engine,
but WEED EATER cannot deny warranty
solely for the lack of receipts or for your failure
to ensure the performance of all scheduled
maintenance. As the small off--road engine
owner, you should be aware that WEED EAT-
ER may deny you warranty coverage if your
small off--road engine or a part of it has failed
due to abuse, neglect, improper mainte-
nance, unapproved modifications, or the use
of parts not made or approved by the original
equipment manufacturer. You are responsi-
ble for presenting your small off--road engine
to an WEED EATER authorized repair center
as soon as aproblemexists. Warranty repairs
12
Download from Www.Somanuals.com. All Manuals Search And Download.
should be completed in a reasonable amount
of time, not toexceed 30days. If you haveany
questions regarding your warranty rights and
responsibilities, you should contact your
nearest authorizedservicecenter, call WEED
EATER at 1--800--554--6723, or send e-mail
correspondence to emission.warranty@
HCOP--emission.com.
WARRANTY COMMENCEMENT DATE:
The warranty period begins on the date the
small off--road engine is purchased.
LENGTH OF COVERAGE: This warranty
shall be for a period of two years from the ini-
tial date of purchase. WHAT IS COVERED:
REPAIR OR REPLACEMENT OF PARTS.
Repair or replacement of any warranted part
will be performed at no charge to the owner at
an approved WEED EATER servicing center.
If you have any questions regarding your war-
ranty rights and responsibilities, you should
contact your nearest authorized service cen-
ter, call WEED EATER at 1--800--554--6723,
or send e-mail correspondence to emission.
warranty@HCOP--emission.com.
CONSEQUENTIAL DAMAGES: WEED
EATER may be liable for damages to other en-
gine components caused by the failure of a war-
ranted part still under warranty. WHAT IS NOT
COVERED: All failures caused by abuse, ne-
glect, or improper maintenance are not cov-
ered. ADD -ON OR MODIFIED PARTS: The
use of add--on or modified parts can be
grounds for disallowing a warranty claim.
WEED EATER is not liable to cover failures of
warranted parts caused by the use of add--on
or modified parts. HOW TO FILE A CLAIM: If
you have any questions regarding your war-
ranty rights and responsibilities, you should
contact your nearest authorized service cen-
ter, call WEED EATER at 1--800--554--6723,
or send e-mail correspondence to emission.
warranty@HCOP--emission.com.
WHERE TO GET WARRANTY SERVICE:
Warranty services or repairs shall be pro-
vided at all WEED EATER service centers.
Call: 1--800--554--6723 or send e-mail corre-
spondence to emission.warranty@HCOP--
emission.com.
MAINTENANCE,
RE-
WARRANTY PERIOD: Any warranted part
which is not scheduled for replacement as re-
quired maintenance, or which is scheduled
only for regular inspection to the effect of “re-
pair or replace as necessary” shall be war-
ranted for 2 years. Any warranted part which
is scheduled for replacement as required
maintenance shallbe warranted for the period
of time up to the first scheduled replacement
point for that part. DIAGNOSIS: The owner
shall not be charged for diagnostic labor
which leads to the determination that a war-
ranted part is defective if the diagnostic work
is performed at an approved WEED EATER
servicing center.
PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS: Any WEED EATER ap-
proved replacement part used in the perfor-
mance of any warranty maintenance or repair
on emission related parts will be provided
without charge tothe owner if thepart is under
warranty. EMISSION CONTROL WARRAN-
TY PARTS LIST: Carburetor, air filter (cov-
ered up to maintenance schedule), ignition
system: spark plug (covered up to mainte-
nance schedule), ignition module, muffler in-
cluding catalyst (if equipped), fuel tank.
MAINTENANCE STATEMENT:The owner is
responsible for the performance of all re-
quired maintenance as defined in the instruc-
tion manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|