Serial Number
Please use this number in registering your warranty
and any correspondence with the factory.
®
GENESIS 1500 LX
Natural Gas Barbecue
Owner’s Manual
®
WARNING: Do not try to light this appliance
without reading "Lighting" instructions
section of this manual.
WARNING: Follow all leak check procedures
carefully in this manual prior to barbecue
operation. Do this even if barbecue was
dealer assembled.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your
gas supplier or your fire department.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
98646
11/97
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Weber-Stephen Products Co. (Weber) hereby
There are no other express warrants except as
set forth herein and any applicable implied
warranties of merchantability and fitness are
limited in duration to the period of coverage of
this express written Limited Warranty. Some
states do not allow limitation on how long an
implied warranty lasts, so this limitation may not
apply to you.
warrants to the ORIGINAL PURCHASER of this
Weber Gas Barbecue that it will be free of
defects in material and workmanship from the
date of purchase as follows:
Aluminum Castings, 10 years,
Recycled Work Surfaces, 10 years
Cooking Grates and Flavorizer Bars, 3 years,
All Remaining Parts, 5 years,
Weber is not liable for any special, indirect or
consequential damages. Some states do not
allow the exclusion or limitation of incidental or
consequential damages, so this limitation or
exclusion may not apply to you.
when assembled and operated in accordance
with the printed instructions accompanying it.
Weber may require reasonable proof of your
date of purchase. THEREFORE, YOU SHOULD
RETAIN YOUR SALES SLIP OR INVOICE.
Weber does not authorize any person or
company to assume for it any other obligation or
liability in connection with the sale, installation,
use, removal, return, or replacement of its
equipment; and no such representations are
binding on Weber.
This Limited Warranty shall be limited to the
repair or replacement of parts which prove
defective under normal use and service and
which on examination shall indicate, to Weber's
satisfaction, they are defective. Before returning
any parts, contact Weber-Stephen Products Co.
Customer Service Center. If Weber confirms the
defect and approves the claim, Weber will elect
to replace such parts without charge. If you are
required to return defective parts, transportation
charges must be prepaid. Weber will return parts
to the purchaser, freight or postage prepaid.
This Warranty applies only to products sold at
retail.
WEBER-STEPHEN PRODUCTS CO.
Customer Service Center
250 South Hicks Road
Palatine, IL 60067-6241
(800) 446-1071
This Limited Warranty does not cover any failures
or operating difficulties due to accident, abuse,
misuse, alteration, misapplication, vandalism,
improper installation or improper maintenance or
service, or failure to perform normal and routine
maintenance, including but not limited to damage
caused by insects within the burner tubes, as set
out in this owner's manual.
Deterioration or damage due to severe weather
conditions such as hail, hurricanes, earthquakes
or tornadoes, discoloration due to exposure to
chemicals either directly or in the atmosphere, is
not covered by this Limited Warranty.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PATENTS AND TRADEMARKS
© 1997 Weber. Weber, , Genesis, Flavorizer and Crossover are
registered U.S. trademarks; Perma-Mount, Gas Catcher,
FlameCheck, Steam-N-Chips, Spider Stopper, and Warm-Up are
U.S. trademarks of Weber-Stephen Products Co., 200 East Daniels
Road, Palatine, IL 60067-6266. U.S.A. Genesis Gas Barbecues
are covered under the following patent nos.: U.S.A. #4,677,964;
4,727,853; #4,777,927; #4,829,978; #4,860,724; #4,941,817;
#4,966,125; #5,070,776; #D293,067; #D316,355; Canada: Rd
1987 Reg. #58,034; #1,279,540; #1,283,586; #1,300,994;
#1,300,995. Printed in the U.S.A.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
WARNINGS................................................................ 2
Warranty & Patents.................................................. 2-3
General Instructions.................................................... 6
Assembly ............................................................. 13-25
Operating Instructions
Lighting........................................................ 26-27
Cooking ............................................................ 28
After a Period of Nonuse ................................. 28
Cleaning ........................................................... 28
Troubleshooting & Maintenance
Annual Maintenance......................................... 29
General Maintenance.................................. 30-32
Troubleshooting................................................ 33
Parts Listing .............................................................. 35
b
c
e
a
d
f
g
h
i
a
FEATURES:
e) Weber Warm-Up Basket for additional cooking or
warming space.
a) Convenient side table, condiment basket,
wire accessory rack and warming rack.
f) Separate burners for temperature control.
b) Heavy gauge porcelain-on-steel lid seals in heat.
g) Crossover Ignition System with Gas Catcher Ignition
Chamber.
c) Rapid read thermometer for precision cooking
measures grill temperature, and can be removed and
inserted into the food.
h) Catch pan catches excess grease.
d) Heavy gauge steel Flavorizer Bars distribute heat
within the grill. Flavorizer Bars heat just the right
amount of drippings for flavoring, letting excess fat
drip past to help prevent flare-ups.
i) Sleek and sturdy base is an attractive addition to your
patio or deck.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
General Instructions
Storage
Your Weber Gas Barbecue is a stationary outdoor cooking
appliance. With the Weber Gas Barbecue you can grill,
barbecue, roast and bake with results that are difficult to
duplicate with indoor kitchen appliances. The closed lid and
Flavorizer Bars produce that "outdoor" flavor in the food.
■ The gas must be turned OFF at the natural gas supply
when the Weber Gas Barbecue is not in use.
Operating area
The natural gas supply is easy to use and gives you more
cooking control than charcoal fuel.
ƽWARNING: Only use this barbecue outdoors in a
well ventilated area. Do not use in a garage, building,
breezeway or any other enclosed area.
■ These instructions will give you the minimum
requirements for assembling your Weber Gas
Barbecue. Please read the instructions carefully
before using your Weber Gas Barbecue. Improper
assembly can be dangerous.
■ Never use your Weber Gas Barbecue under an
unprotected combustible roof or overhang.
■ Your Weber Gas Barbecue is not intended to be
■ Not for use by children.
installed in or on recreational vehicles and/or boats.
■
will
If there are local codes that apply to gas grills, you
■ Do not use combustible materials within 24 inches of
have to conform to them. If there are no local codes,
you must conform to the latest edition of the National
Fuel Gas Code: ANSI Z 223.1.
the top, bottom, back or sides of the grill.
■ The entire cooking box gets hot when in use. Do not
leave unattended.
■
This Weber Gas Barbecue is designed for natural
(piped in city) gas only. Do not use Liquid Propane
(LP) bottled gas. The valves and orifices are for
natural gas only.
■ Keep any electrical supply cord away from any heated
surface.
■ Keep the cooking area clear of flammable vapors and
liquids, such as gasoline, alcohol, etc., and
combustible materials.
■ Do not use with charcoal fuel.
■ Check that the area under the control panel and the
bottom tray are free from debris that might obstruct
the flow of combustion or ventilation air.
Gas supply testing
■ Disconnect your Weber Gas Barbecue when the gas
supply is being tested at high pressures. This
appliance and its individual shutoff valve must be
disconnected from the gas supply piping system
during any pressure testing of that system at test
pressures in excess of 1/2 psig (3.5 kPa).
■ Turn off your Weber Gas Barbecue when the gas
supply is being tested at low pressures. This appliance
must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at the
pressure equal to or less than 1/2 psig (3.5 kPa).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice Before Installation
Contact your local municipality for any building codes regulating outdoor barbecue installations. In absence of
local codes, you must conform to the latest edition of ANSI Z223.1.
WE RECOMMEND THAT THIS INSTALLATION BE DONE BY A PROFESSIONAL.
Outside underground piping
General Specifications for
Piping
American National Standards Institute (ANSI)
Recommendations for gas supply installations:
Outside underground piping may be copper tubing, type
K or L (ASTM B88) or polyethylene plastic tube PE3306
(Minimum wall thickness .062") meeting ASTM 2513,
latest specifications.
Steel pipe is not recommended for underground use
unless it is protected with an approved coating, insulated
Connections:
■ This barbecue is designed to operate at 7 inches of
from hose piping and cathodically protected.
water column pressure (.2526 psi).
It is recommended that copper tubing be corrosion
protected with a satisfactory material such as TC Mastic.
■ A manual shut-off valve must be installed outdoors,
immediately ahead of any connections or change in
pipe material.
All buried fittings should be corrosion protected with a
satisfactory material such as TC Mastic.
■ An additional manual shut-off valve indoors should be
installed in the branch fuel line in an accessible
location near the supply line.
Underground piping must have a minimum of 10" cover.
Plastic tubing
Plastic tubing is suitable only for outside underground use.
■ The point of tie into the branch line should be carefully
selected to avoid a drip leg or be downstream of a
valve controlling another appliance.
■ The transition from metallic pipe to plastic pipe should
be made outside and at least 10" underground.
■ When compression or crimp type mechanical joints
are used with plastic pipe, it is advisable to use an
internal rigid stiffener in conjunction with the fitting.
■ Pipe compound should be used which is resistant to
action of natural gas when connections are made.
■ The outdoor connector must be firmly attached to
■ The stiffener should be assembled flush with the end
of the tube and extend at least to the outside edge of
the compression fitting.
rigid, permanent construction.
Gas line piping
■ If the length of line required does not exceed 50 feet,
use a 5/8" O.D. tube. One size larger should be used
for lengths greater than 50 feet.
Testing connections
You will need a soap and water solution and a rag or
brush to apply it.
■ Indoor and above ground piping can be steel or copper.
All connections and joints must be thoroughly tested for
leaks after gas has been turned into the line.
Steel
New standard weight (Schedule 40) steel pipe with
malleable iron fittings.
ƽ DANGER
Do not use an open flame to check for
gas leaks. Be sure there are no sparks or
open flames in the area while you check
for gas leaks. This will result in a fire or
explosion which can cause serious bodily
injury or death, and damage to property.
Copper
New copper tubing type K or L.
Copper tubing must meet requirements of ASTM B88
latest edition.
Use flared fittings. Metallic ball sleeve compression fittings
must not be used.
Copper tube joints may be soldered or brazed with material
having a melting point in excess of 1,000°F.
Wet the fitting with a soap and water solution. Any bubbles
that form or grow indicate a leak. If bubbles occur shut off
gas, tighten the fitting, and retest.
ƽWARNING: If a leak persists after tightening the
fitting, turn gas off at the supply. DO NOT OPERATE
YOUR BARBECUE. Contact Weber-Stephen Customer
Service.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical natural gas supply installation to a
Typical natural gas supply installation over
concrete patio or pad
an existing post
View from behind
barbecue
View from behind
barbecue
Outside
Outside
Accessible
Locking Shut off
Accessible
Locking Shut off
Inside
Indoor Shut off
Inside
Gas Supply
Indoor Shut off
Gas Supply
Figure 1
Figure 3
ƽCAUTION: Follow "General Specifications for Piping"
in this manual.
ƽWARNING: Turn off the natural gas supply at the
source before working on the post.
We recommend that this installation be done by a
professional.
Prepare the post so that it will be approximately 2 inches
above the pad or ground. Inspect the gas supply line at
the post for any sign of deterioration or corrosion.
ƽCAUTION: Combustible materials should never be
within 24 inches of the top, bottom, back or sides of the
barbecue. Do not locate under overhead combustible
construction.
ƽCAUTION: If you are in doubt as to the condition of
an existing natural gas supply line, you should
contact a professional or your local gas utility before
attempting any assembly.
Typical natural gas supply installation to a
wood deck
ƽCAUTION: Combustible materials should never be
within 24 inches of the top, bottom, back or sides of the
barbecue. Do not locate under overhead combustible
construction.
View from behind
barbecue
Outside
Accessible
Locking Shut off
Inside
Indoor Shut off
Gas Supply
Figure 2
ƽCAUTION: Follow "General Specifications for Piping"
in this manual.
We recommend that this installation be done by a
professional.
ƽCAUTION: Combustible materials should never be
within 24 inches of the top, bottom, back or sides of
the barbecue. Do not locate under overhead
combustible construction.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended concrete pad requirements
We recommend a pad a minimum of 40 inches left to right,
20 inches front to back and 4 inches deep (1.85 cubic feet).
Figure 4.
Note - Cubic feet is determined by multiplying length times
width times depth and dividing by 1728.
20”
40”
4”
Figure 4
If you use a concrete bag mix, use the mix for maximum
strength. An average 80 pound bag of concrete mix will
make approximately 2/3 of a cubic foot of concrete.
Note - Follow the concrete bag mix, manufacturers
recommendations concerning pad preparation, gravel,
sand, etc. Figure 5.
Concrete Pad
Crushed stone,
sand or gravel
Earth
Figure 5
ƽCAUTION: Allow fresh concrete to cure completely
before attempting to anchor the barbecue to the
concrete.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1
Assembly
Tools needed
Check package contents
Screwdrivers, regular and
Cooking box
(assembly)
Phillips
Hammer
One 7/16 inch, 11/16, and 3/4 inch or two adjustable
wrenches
Lid
(assembly)
Pliers
Tape Measure
Bottom tray
Pencil
Control panel
Work table
Electric drill
Supplies needed
You will need a soap and water solution to check for gas
leaks. (See Step "Check for gas leaks.")
Note - The hardware size of nuts, bolts, and screws is
given. For example "1/4-20 x 2 inch bolt" means a bolt
1/4 inch in diameter with 20 threads to the inch, 2 inches
long. On a small screw for example, "6-32 x 1/2 inch
screw" means a number 6 screw, with 32 threads to the
inch, 1/2 inch long.
Gas supply line
(with the flare fitting
loosely attached
for shipping purposes)
While we give much attention to our products,
unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call the Weber
Customer Service Center toll free 1-800-446-1071 to
receive immediate assistance. Have your owner’s
manual and serial number of the barbecue available for
reference.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Left frame
Front Panel
Cooking grate (2)
Catch pan holder
Catch Pan
Right frame
Side frame (2)
Accessory rack
Drip pans (2)
Thermometer
Warm-Up Basket
Warming Rack
Condiment basket
Spacer bracket
Five long Flavorizer Bars
Eight short Flavorizer Bars
Side panel (2)
Base panel
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Check contents of hardware packs
Ten plastic buttons
End bracket
Three burner control knobs
Three tool holders
Three tubing plugs
Manifold bracket
Two Phillips screws/washers
Two hinge pins
(hardware size: 1/4 x 1 1/2 inch clevis pin)
(actual size)
One 1/4-20 x 2 inch bolts
(actual size)
Six 1/4-20 x 1/2 inch bolts
(actual size)
One 1/4-20 keps nut
Seven nylon washers
(actual size)
Two hair pin cotters
(actual size)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2
Step 3
Assemble the frame
Continue frame assembly
You will need: left frame, right frame, two nylon washers,
two 1/4-20 x 1/2 inch bolts and a 7/16 inch wrench.
You will need: frame assembly, two side frames,
four 1/4-20 x 1/2 inch bolts, four nylon washers
and a 7/16 inch wrench.
Note - Work on carpeted area (on grass, or on one of the
boxes) to protect the finish during frame assembly.
Assemble one side frame onto the leg tabs of the right
frame, and the second side frame onto the leg tabs of
the left frame. Make sure the anchoring base plates are
facing in toward each other. The tabs must be on the
inside of the frames when the joints are closed.
Put the frame pieces so the leg tabs are up. Put the right
frame to your right and left frame to your left. Figure 1.
Slip the two frame halves together with the tabs inside,
until the tabs of the right frame are inside the left frame
and the holes align. Figure 1 (a).
Add washers, then bolts. Do not fully tighten these
bolts. You will tighten them once the base is anchored.
Figure 2 (a).
Slip washers over bolts; insert and tighten bolts. (If you try
to insert a bolt and there are no holes, you have the left
frame turned the wrong way. Turn the left frame around.)
Figure 1 (b).
Turn frame assembly right side up.
(a)
Anchoring base
plates are facing in
(a)
Do not fully tighten
these bolts
Figure 2
(b)
Figure 1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4
Step 5
Measure and drill holes
Typical installation of the base for an existing
concrete patio, new pad or wood deck
You will need: Completed frame assembly, base panel,
tape measure, and pencil.
ƽCAUTION: Combustible materials should never be
within 24 inches of the top, bottom, back or sides of
the barbecue. Do not locate under overhead
combustible construction.
ƽCAUTION: Combustible materials should never be
within 24 inches of the top, bottom, back or sides of
the barbecue. Do not locate under overhead
combustible construction.
Note - With the lid open the depth of the barbecue is
28 inches, front to back.
Note - With the lid open the depth of the barbecue is
28 inches, front to back.
For anchoring, we recommend use of one of the following
methods:
Set the completed frame assembly in position on your
deck, concrete pad, or patio for anchoring. Measure the
distance from the outside of the base plate to the outside
of the other base plate. It should be 26 1/2” across.
Figure 3.
ƽWARNING: Whichever method used, the base must
be bolted down (anchored) at a minimum of four
anchoring points (two per side) prior to barbecue
assembly. One anchor in each corner of the base
plate. Figure 5.
Note: If the measurement is not 26 1/2” across adjust the
legs as necessary so that the measurement is 26 1/2”.
1
4
2
3
Figure 5
Figure 3
Place the base panel in between the legs to insure fit.
Figure 4. Once the fit is established, remove the base
panel and mark the holes.
ƽCAUTION: A minimum of 2 bolts are required on
each side.
You are now ready to anchor the base.
Figure 4
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Method 3 - Concrete
Typical installation of the base for an existing
concrete patio, new pad or wood deck (continued)
A 3/8 inch machine screw anchor, using a 3/8-16 x
1 1/2 inch machine screw and a flat washer. Figure 8.
Method 1 - Concrete
Note - Use a 3/4 inch diameter concrete drill bit for drilling
the hole for the screw base. The machine screw anchor
requires a setting tool.
A strike anchor, a minimum size of 3/8 inch x 3 1/2 inches
long with a 3/8 inch flat washer and 3/8 inch nut. Figure 6.
Note - Use a 3/8 inch diameter concrete drill bit for drilling
the hole for the strike anchor.
3/8-16 x 1 1/2 machine screw
3/8 inch flat washer
Strike anchor
3/8 inch nut
Mount plate
3/8 inch screw anchor
3/8 inch flat washer
Drilled hole
Mount plate
Drilled hole
Figure 8
Figure 6
Method 2 - Concrete
A concrete lag bolt, a minimum of 3/8 inch x 2 1/2 inches
long with a 3/8 inch diameter long lag shield and a 3/8 inch
flat washer. Figure 7.
Note - Use a 5/8 inch concrete drill bit for drilling the hole
for the lag shield.
Concrete lag bolt
3/8 inch flat washer
Mount plate
Lag shield
Drilled hole
Figure 7
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical installation of the base for an existing
Step 6
concrete patio, new pad or wood deck (continued)
Add front panel and tighten all frame bolts
You will need: front panel and two plastic buttons.
Method 4 - Wood deck
After assembling the base according to the assembly
instructions, position the base assembly on your deck
for anchoring.
Align the panel with the holes in the frame and insert
the plastic buttons through the front panel and frame.
Figure 11.
Plastic buttons
shown from the rear
of the barbecue
ƽCAUTION: Combustible materials should never be
within 24 inches of the top, bottom, back or sides of
the barbecue. Do not locate under overhead
combustible construction.
ƽCAUTION: For a deck installation, it is recommended
to anchor one screw into a joist.
Note - With the lid open, the depth of the barbecue is
28 inches, front to back.
Anchor the base to the deck. We recommend using a
minimum of a 3/8 inch x 1 1/2 inch lag bolt with a 3/8 inch
flat washer. Figure 9.
Note - Use a 3/16 inch drill bit for drilling a pilot hole for a
3/8 inch lag bolt.
3/8 inch x 1 1/2 inch lag bolt
3/8 inch flat washer
Mount plate
Drilled hole
Figure 11
Fully tighten the 1/4-20 bolts in the frame assembly, that
you only started in Step “Continue Frame Assembly”
Figure 12.
Figure 9
ƽWARNING: Whichever method used, the base must
be bolted down (anchored) at a minimum of four
anchoring points (two per side) prior to barbecue
assembly. One anchor in each corner of the base plate.
Figure 10.
Figure 12
1
4
2
3
Figure 10
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Your Weber Gas Barbecue burner assembly has been
factory assembled, pressure and flame tested. As a safety
precaution we recommend you check the burner alignment:
Step 7
Add cooking box
You will need: frame assembly, cooking box assembly,
spacer bracket, 1/4-20 x 2 inch bolt, nylon washer,
1/4-20 keps nut, pliers and a 7/16 inch wrench.
a) Are the ends of the burners under the washers at the
left rear and left front of the cooking box? The screws
are only guides. Do not tighten. Figure 15 (a).
Set the cooking box in the frame so the burner tubes are
under the frame brace. Figure 13.
b) Are the wing nuts under the burner assembly hand
tight? Do not tighten with pliers. Figure 15 (b).
Note: Be careful when sliding the burner tubes through
If you answered YES to a and b, the burners are
correctly aligned. If you answered NO, the burners are
misaligned. Contact Weber-Stephen Customer Service.
Do not use barbecue.
the side frame.
Burner tubes
Frame brace
Guide screw
(a)
Figure 13
View from
behind
cooking
box
Slide the cooking box to the left within the frame. Put
nylon washer on the bolt. Take the spacer bracket and
hold it up to the frame making sure both tabs fit
underneath the frame cross piece. Figure 14 (a). Insert
the bolt through the center hole in the spacer bracket,
frame and cooking box with the head of the bolt outside
the spacer bracket. Figure 14 (b). Add the keps nut.
Tighten by holding the bolt with pliers while you tighten
(b)
Wing nuts
Figure 15
the nut with the 7/16 inch wrench.
Frame cross
piece
Spacer bracket
Keps nut
Bolt
Nylon washer
Figure 14
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 8
Step 9
Connect barbecue gas supply line to the natural
gas supply
Check all valves are off
You will need: one burner control knob.
Note - We recommend that the connection between
the barbecue gas supply line and the natural gas
supply be flare to flare. A 3/8-inch flare fitting has
been included with the barbecue gas supply line of
your gas barbecue. The fitting is loosely connected for
shipping and should be removed before installation.
(Valves are shipped in the OFF position, but you should
check to be sure.) Put the knob on each valve. Check by
pushing down and turning clockwise. If they do not turn
they are off. Proceed to the next step. Figure 17.
You will need: barbecue gas supply line, 3/8 inch flare
fitting, 3/4 inch and 11/16 inch wrenches.
ƽWARNING: This barbecue is NOT portable. It must
be bolted down at all times when it is connected to a
natural gas supply.
Unscrew the 3/8 inch flare fitting from the barbecue gas
supply line. Apply pipe sealant to the threads of the
pipe fitting. Screw the pipe fitting end of the 3/8 inch
flare fitting into the natural gas supply pipe. Tighten with
an 11/16 inch wrench. Figure 16 (a).
Figure 17
Step 10
Attach the flare nut on the barbecue gas supply line to the
flare fitting end of the 3/8 inch flare fitting. Tighten with a
3/4 inch wrench. Figure 16 (a).
Install manifold bracket
You will need: manifold bracket.
Attach the flare nut at the other end of the barbecue gas
supply line to the manifold fitting. Tighten with a 3/4 inch
wrench. Figure 16 (b).
Hook the bracket onto the manifold at the center burner
valve. Figure 18. Place your hand underneath the bracket.
Lift the bracket, manifold and cooking box slightly as a unit
and hook onto the frame brace. Figure 18 (a).
(b)
Frame brace
Manifold bracket
(a)
Figure 18
Apply pipe
sealant here
Figure 16
View from below
cooking box
(a)
Natural Gas
Supply Pipe
Pipe fitting end
of 3/8-inch
Flare Fitting
Flare fitting end of
3/8-inch Flare Fitting
Barbecue gas
supply line
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 11
Step 12
Install igniter
Purge air from gas lines
You will need: one burner control knob.
Note - The igniter wires are already attached to the Gas
Catcher Ignition Chamber and the igniter. This was done to
factory test the ignition system.
ƽ DANGER
The igniter lock nut is on the igniter.
Be sure there are no sparks or open flames
in the area while purging. This can cause
fire, explosion or serious bodily injury.
Insert the top of the igniter up through the large part of
the keyhole in the frame brace. Figure 19 (b). Loosen the
igniter lock nut and slide the igniter into the small part of
the keyhole. Figure 19 (c). Tighten the igniter lock nut.
Figure 19.
It is necessary to bleed the air out of newly installed gas
lines. Turn gas supply ON at the source. Put on the front
burner control knob. Push the front burner control knob
down and turn to HI. When you start to smell gas, turn
front burner control knob to OFF. Figure 20.
Note - If the igniter works loose, carefully tighten the igniter
lock nut with an adjustable wrench or pliers.
(a)
Frame brace
(b)
Figure 20
Figure 19
Keyhole in
frame brace
Igniter lock nut
(c)
Frame brace
Small part of keyhole
in frame brace
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Check:
Step 13
a) Gas supply line to manifold connection. Figure 22 (a).
Check for gas leaks
ƽWARNING: If there is a leak at connection a,
retighten the fitting with a wrench and recheck for
leaks with soap and water solution.
ƽ DANGER
Do not use an open flame to check for gas
leaks. Be sure there are no sparks or open
flames in the area while you check for
leaks. This will result in a fire or explosion
which can cause serious bodily injury or
death and damage to property.
If a leak persists after retightening the fitting, turn
OFF the gas. DO NOT OPERATE THE BARBECUE.
Contact Weber-Stephen Customer Service.
b) Valves to manifold connections. Figure 22 (b).
c) Barbecue gas supply line to natural gas supply
connection. Figure 22 (c).
ƽWARNING:You should check for gas leaks every
ƽWARNING: If there is a leak at connections b or c,
turn OFF the gas. DO NOT OPERATE THE BARBECUE.
Contact Weber-Stephen Customer Service.
time you disconnect and reconnect a gas fitting.
Note - All factory made connections have been thoroughly
checked for gas leaks. The burners have been flame
tested. As a safety precaution you should recheck all
fittings for leaks before using your Weber Gas Barbecue.
Shipping and handling may have loosened or damaged a
gas fitting.
When leak checks are complete, turn gas supply OFF
and rinse connections with water.
(a)
ƽWARNING: Perform these leak checks even if your
barbecue was dealer or store assembled.
You will need: soap and water solution and a rag or brush
to apply it.
(b)
To perform leak checks: Turn ON gas supply at the source.
Figure 21.
Gas supply shut
off at the house
Figure 21
ƽWARNING: Do not ignite burners while leak checking.
Check for leaks by wetting the connections with the soap
and water solution and watching for bubbles. If bubbles
form or if a bubble grows there is a leak.
(c)
Note - Since some leak test solutions, including soap and
water, may be slightly corrosive, all connections should be
rinsed with water after checking for leaks.
Figure 22
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 14
Step 15
Add base panel
You will need: Base panel.
Install side panels
You will need: two side panels, and eight plastic buttons.
Put the right side in and down, tilt and set the left side in
place. Figure 23.
From the inside of the frame assembly, set the left side
panel in place between the side frame legs.
Notice that there are two sets of holes in each side
panel. Align the holes in the side panel to match the
holes in the left side frame legs. Push in the four plastic
buttons. Figure 24 (a).
Repeat with the right side panel.
top
Base panel
Left side
panel
Figure 23
Right side
panel
bottom
(a)
Figure 24
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 16
Step 17
Install Flavorizer Bars and Cooking Grates
Install the bottom tray
You will need: five long Flavorizer Bars, eight short
Flavorizer Bars and two cooking grates.
You will need: bottom tray, catch pan holder, catch pan
and one drip pan.
Set the long Flavorizer Bars side to side in the lower
position, then set the short Flavorizer Bars front to back
in the upper position in the cooking box. Figure 25.
Finger grip on front
edge of bottom tray
Front side of catch
pan holder
Figure 27
Hook the ends of the catch pan holder into the hole in the
bottom tray. Figure 28. The front of the catch pan holder
must be on the same side as the finger grip of the
bottom tray.
Figure 25
The open "U" of the cooking grates goes down. Set
the cooking grates onto the ledges in the cooking box.
Figure 26.
Finger grip
Figure 28
Slide the bottom tray onto the mounting rails under the
cooking box with finger grip toward you. Figure 29.
ƽCAUTION: Do not line bottom tray with aluminum
foil. It can cause grease fires by trapping the grease
and not allowing grease to flow into the catch pan.
Figure 26
Bottom tray
Figure 29
Put the foil drip pan into the catch pan.
Slide the catch pan into the catch pan holder with its
finger grip towards you.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 18
Step 19
Install Lid
Add tool holders, control panel and burner
control knobs
You will need: lid, two hinge pins and two hair pin cotters.
You will need: three tool holders, control panel, two
Phillips screws/washers, a Phillips screwdriver, and three
burner control knobs.
Set the lid in place. Align the hinges at the rear of the
barbecue. Insert hinge pins from the outside. Insert hair pin
cotters into the small holes in the hinge pins. Figure 30.
Hook the tool holders over the frame rail and snap down
into place. Figure 31.
Hair pin cotter
Hinge pin
Set the control panel in place over both frame braces.
(Hold the Crossover Ignition button up while setting the
control panel in place.) Line up the holes in the control
panel with the holes in the inserts in the frame brace.
Insert screws and tighten with a Phillips screwdriver until
snug. Do not overtighten. Figure 31 (a).
Push on the burner control knobs. Figure 31 (b).
Insert in
frame brace
(a)
Crossover
Ignition
Button
Figure 30
Control panel
Phillips screws/
washers
(b)
Tool holders
Figure 31
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 20
Step 21
Install the condiment basket
You will need: condiment basket and end bracket.
Install the accessory rack
You will need: accessory rack.
Insert one wire end of the condiment basket into the hole
in the side frame. Figure 32 (a). Insert the opposite wire
end of the condiment basket into the hole in the end
bracket. Hold the end bracket at an angle so the lower tab
is inside the frame tube. Push the bracket into the frame.
Figure 32 (b). Check to see that the lower tab of the
bracket is hooked in the slot in the frame. Figure 32 (c).
Rest the left end of the accessory rack on the base
panel. Figure 33 (a).
Insert the right hooks into the right side frame slots.
Figure 33 (b).
Raise the left end up and slide left hooks into the left
side frame slots. Figure 33.
To fully seat the bracket, you may have to tap it lightly
with a hammer.
ƽWARNING: If the end bracket is in any way cracked
or damaged, do not use the condiment basket. Call
our Customer Service Center to order a new part.
Left side
frame slots
Wire end
(a)
(a)
Right side
frame
(b)
Left hooks
(b)
Figure 33
Slot in frame
(view from below)
(c)
Figure 32
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 22
Complete accessory installation
You will need: Warm-Up Basket, warming rack, work
table, three tubing plugs, thermometer and a hammer.
Insert one end of the Weber Warm-Up Basket into the hole
in the right end of the lid and the other end into the slot in
the left end of the lid. Figure 34 (a).
Set the warming rack into the slots at the rear of the
cooking box. Figure 34 (b).
Set the work table onto the left side rails. Figure 34 (c).
Insert the thermometer into its holder. Figure 34 (d).
Insert the tubing plugs into the ends of the frame. To fully
seat the plugs, you may have to tap them lightly with a
hammer. Figure 34 (e).
(a)
(b)
(d)
(c)
(e)
Figure 34
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
1) Open the lid. Figure 1.
Lighting
Summary lighting instructions are on the control panel.
2) Make sure all burner control knobs are turned OFF.
(Push each burner control knob down and turn
clockwise.)
ƽ DANGER
3) Turn gas supply valve on.
Failure to open lid while igniting the
barbecue, or not waiting 5 minutes to
allow the gas to clear if the barbecue
does not light, may result in an explosive
flame-up which can cause serious bodily
injury or death.
ƽWARNING: Do not lean over open barbecue. Keep
your face and body at least one foot away from the
matchlight hole when lighting the barbecue.
4) Push Front burner control knob down and turn to
START/ HI.
5) Push the Crossover Ignition Button several times, so it
clicks each time.
Crossover Ignition System
6) Check that the burner is lit by looking through the
matchlight hole on the front of the cooking box.
Note - The Crossover Ignition System ignites the Front
burner with a spark from the igniter electrode inside the Gas
Catcher Ignition Chamber. You generate the energy for the
spark by pushing the Crossover Ignition Button until it clicks.
ƽWARNING: If the burner does not light, turn the
Front burner control knob to OFF and wait 5 minutes
to let the gas clear before you try again or try to light
with a match.
ƽWARNING: Check gas supply line before each use
of barbecue for nicks or cracking. If the gas supply
line is found to be damaged in any way, do not use the
barbecue. Replace using only Weber authorized
replacement gas supply line. Order from Weber-
Stephen Products Co., Customer Service Center.
7) After the FRONT burner is lit you can turn on the other
burners.
Note - Always light the FRONT burner first. The other
burners ignite from the FRONT burner.
Crossover Ignition System
To Extinguish
1
Turn gas supply OFF at the source, then push down
and turn each burner control knob clockwise to OFF.
2
7
5
6
4
Figure 1
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Lighting
ƽWARNING: If the burner does not light, turn the Front
burner control knob to OFF and wait 5 minutes to let
the gas clear before you try again or try to light with
a match.
ƽ DANGER
Failure to open lid while igniting the
barbecue, or not waiting 5 minutes to
allow the gas to clear if the barbecue
does not light, may result in an explosive
flame-up which can cause serious bodily
injury or death.
7) After the FRONT burner is lit you can turn on the other
burners.
Note - Always light the FRONT burner first. The other
burners ignite from the FRONT burner.
To Extinguish
1) Open the lid. Figure 2.
2) Make sure all burner control knobs are turned OFF.
(Push each burner control knob down and turn
clockwise.)
Turn gas supply OFF at the source, then push down
and turn each burner control knob clockwise to OFF.
3) Turn gas supply valve on.
4) Strike a match and put the flame into the matchlight
hole in the front of the cooking box.
Manual Lighting
1
2
7
4,6
5
Figure 2
ƽWARNING: Do not lean over open barbecue. Keep
your face and body at least one foot away from the
matchlight hole when lighting the barbecue.
5) Push Front burner control knob down and turn to
START/ HI.
6) Check that the burner is lit by looking through the
matchlight hole on the front of the cooking box.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooking
After a Period of Nonuse
You can adjust the FRONT, CENTER and BACK burners
as desired. The control settings High (H), Medium (M), Low
(L), or Off (O) are described in your Weber cookbook. The
cookbook uses these notations to describe the settings of
the FRONT, CENTER, and BACK burners. For example, to
sear steaks you would use (HHH) (all burners at high).
Then to complete cooking you would use (MOM) (FRONT
at medium, CENTER off, and BACK at medium). See your
Weber cookbook for detailed cooking instructions.
■ The Weber Gas Barbecue should be checked for gas
leaks and any obstructions in the burner tubes before
using. (See Sections General and Annual Maintenance.)
■ Check that the areas under the control panel and the
bottom tray are free from debris that might obstruct
the flow of combustion or ventilation air.
■ The Spider Stopper Guards should also be checked for
any obstructions. (See Section "Annual Maintenance.")
Note: The temperatures inside your cooking box, for the
first few uses, while surfaces are still very reflective, may
be hotter than those shown in your cookbook. Cooking
conditions may require the adjustment of the burner
controls to attain the correct cooking temperatures.
■ Keep the appliance area clear and free from
combustible materials, gasoline and other flammable
vapors and liquids.
ƽCAUTION: Replace thermometer in lid when not in
use. Do not leave thermometer in food while cooking.
Periodic Cleaning
If burners go out during cooking, open lid, turn off all
burners and wait 5 minutes before relighting.
ƽWARNING: Turn your Weber Gas Barbecue OFF and
wait for it to cool before cleaning.
Preheating
ƽCAUTION: Do not clean your Flavorizer Bars or
cooking grates in a self-cleaning oven. Replacement
cooking grates and Flavorizer Bars are available
through your retailer or the Weber-Stephen Customer
Service Center.
Your Weber Gas Barbecue is an energy efficient appliance.
It operates at a low B.T.U. rate for economy. To preheat,
after lighting, close lid and turn all burners to high (HHH).
Preheating to between 500° and 550° F (260° and 290° C)
will take 10 to 15 minutes depending on conditions such as
air temperature and wind.
Outside surfaces - Use a warm soapy water solution.
ƽCAUTION: Do not use oven cleaner, abrasive
cleansers (kitchen cleansers) cleaners that contain
citrus products or abrasive cleaning pads on barbecue
or cart surfaces.
Drippings and grease
The Flavorizer Bars are designed to "smoke" the right
amount of drippings for flavorful cooking. Excess drippings
and grease accumulate in the catch pan under the bottom
tray. Disposable foil liners are available that fit the catch pan.
Bottom tray - Remove excess grease and then wash with
warm soapy water.
ƽWARNING: Check the bottom tray for grease build-
up before each use. Remove excess grease to avoid a
grease fire in the bottom tray.
Flavorizer Bars and Cooking Grates - Clean with a
suitable brass bristle brush. As needed, remove from grill
and wash with warm soapy water.
Catch pan - Disposable foil trays are available, or you can
line the catch pan with aluminum foil. To clean the catch
pan, wash with warm soapy water.
Thermometer - Wipe with warm soapy water, clean with
plastic scrub ball. Do not put in dishwasher or submerge
in water.
Inside cooking box - Brush any debris off of burners tubes.
DO NOT ENLARGE BURNER PORTS (OPENINGS).
Wash inside of cooking box with warm soapy water.
Inside Lid - While lid is warm, wipe inside with paper towel
to prevent flaking due to grease build-up.
Work tables and accessory trays - Use any household
cleaners on these surfaces except those that contain acid,
mineral spirits or Xylene. Rinse well after cleaning.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Check:
Annual Maintenance
After a period of nonuse we recommend that you perform
a) Gas supply line to manifold connection. Figure 3 (a).
ƽWARNING: If there is a leak at connection (a),
retighten the fitting with a wrench and recheck for
leaks with soap and water solution.
the following maintenance procedures for your safety.
ƽWARNING: Check gas supply line before each use
of barbecue for nicks or cracking. If the gas supply
line is found to be damaged in any way, do not use the
barbecue. Replace using only Weber authorized
replacement gas supply line. Order from Weber-
Stephen Products Co., Customer Service Center.
If a leak persists after retightening the fitting, turn OFF
the gas. DO NOT OPERATE THE BARBECUE. Contact
Weber-Stephen Customer Service.
b) Valves to manifold connections. Figure 3 (b).
c) Barbecue gas supply line to natural gas supply
connection. Figure 3 (c).
ƽCAUTION: If the barbecue gas supply line is damaged
in any way or leaking, do not use the barbecue.
■ Inspect the burners for correct flame pattern. Clean if
necessary, following the procedures outlined in the
"General Maintenance" section of this manual.
ƽWARNING: If there is a leak at connections (b) or (c),
turn OFF the gas. DO NOT OPERATE THE BARBECUE.
Contact Weber-Stephen Customer Service.
When leak checks are complete, see steps “Add side
panels” and “Add base panel” to reinstall. Turn gas supply
OFF at the source and rinse connections with water.
■ Check all gas fittings for leaks.
ƽ DANGER
Do not use an open flame to check for gas
leaks. Be sure there are no sparks or open
flames in the area while you check for
leaks. This will result in a fire or explosion
which can cause serious bodily injury or
death, and damage to property.
(a)
(b)
ƽWARNING: You should check for gas leaks every
time you disconnect and reconnect a gas fitting.
You will need: a soap and water solution and a rag or
brush to apply it.
To perform leak checks: Make sure all burners are in the
OFF position. Turn on gas supply.
Refer to the steps “Add side panels” and “Add base panel”
to remove the panels to expose the gas supply line for
leak checking.
ƽWARNING: Do not ignite burners while leak checking.
Figure 3
(c)
Check for leaks by wetting the connections with the soap
and water solution and watching for bubbles. If bubbles
form or if a bubble grows there is a leak.
Note - Since some leak test solutions, including soap and
water, may be slightly corrosive, all connections should be
rinsed with water after checking for leaks.
Inspection and Cleaning of the Weber Spider
Stopper Guards
To inspect the Spider Stopper Guards, remove the control
panel and look to see if they have dust or dirt on their outside
surfaces. If they are dirty, brush off the outside surface of the
Spider Stopper Guards with a soft bristle brush (an old
toothbrush for example). Check that there are no gaps in the
Spider Stopper Guards’ seams or in the fit around the
burners or valves. (See Section "General Maintenance".)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Burner Flame Pattern
General Maintenance
Weber Spider Stopper Guards
The Weber Gas Barbecue burners have been factory set
for the correct air and gas mixture. The correct flame
pattern is shown in Figure 6.
Your Weber Gas Barbecue, as well as any outdoor gas
appliance, is a target for spiders and other insects. They
can nest in the venturi section of the burner tubes. This
blocks the normal gas flow, and can cause the gas to flow
back out of the air shutter. Figure 4. This could result in a
fire in and around the air shutters, under the control panel,
causing serious damage to your barbecue.
Tips occasionally yellowish
Burner inside
cooking box
Light blue
Venturi
Dark blue
Flames
Figure 6
If the flames do not appear to be uniform the length of the
burner tube, follow the burner cleaning procedures.
Venturi fin
Air shutter
Figure 4
The Weber Spider Stopper Guard is factory installed. It fits
tightly around the air shutter section of the burner tube and
the valve, thereby preventing spiders and other insects
access to the burner tubes through the air shutter openings.
Figure 5.
Main Burner Cleaning Procedure
Turn off the gas supply. Remove the manifold. (See
Section “Replacing the main burners”.)
Look inside each burner with a flashlight. Figure 7.
Weber Spider
Stopper Guard
Figure 7
Clean the inside of the burners with a wire (a straightened
out coat hanger will work). Figure 8. Check and clean the
air shutter opening at the ends of the burners. Check and
clean the valve orifices at the base of the valves. Use a
brass bristle brush to clean outside of burners. This is to
make sure all the burner ports are fully open.
Figure 5
We recommend that you inspect the Weber Spider
Stopper Guards at least once a year. (See section
“Annual Maintenance”.) Also inspect and clean the
Spider Stopper Guards if any of the following
symptoms should ever occur.
1. The smell of gas in conjunction with the burner flames
appearing yellow and lazy.
2. Barbecue does not reach temperature.
3. Barbecue heats unevenly.
Figure 8
ƽCAUTION: Do not enlarge the burner ports when
4. One or more of the burners do not ignite.
cleaning.
ƽ DANGER
Replacing Main Burners
Failure to correct these symptoms may
result in a fire which can cause serious
bodily injury or death and cause damage
to property.
a) Your Weber Gas Barbecue must be OFF and cool.
b) Turn gas OFF at source.
c) Remove control panel: take off the burner control
knobs. Remove the screws holding the control panel
in place. Lift off the control panel.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
d) Unlatch the Spider Stopper Guards and remove.
Figure 9.
i) To reinstall the burners, reverse steps c) through g).
ƽCAUTION: The burner openings must be positioned
properly over the valve orifices. Figure 13 (a).
Check proper assembly before fastening manifold in place.
Figure 13 (b).
(a)
Figure 9
e) Disconnect gas supply line.
f) Remove the manifold bracket and unscrew the two
wing nuts that hold the manifold to the cooking box.
Pull the manifold and valve assembly out of the
burners and carefully set it down. Figure 10.
(b)
View from behind
cooking box
Wing nuts
Figure 13
Figure 10
j) Reinstall the Spider Stopper Guards. Slightly rotate
the Spider Stopper Guards so that the seams are in
line with the Venturi fins. There should be no gaps in
the seams or in the fit around the burners and valves.
Figure 14.
g) Slide the burner assembly out from under the guide
screw and washer in the corners of the cooking box.
Figure 11.
Guide screw
Check fit
around valve
Venturi fin
Figure 11
h) Lift and twist the burner assembly slightly, to separate
the crossover tube from the burners. Figure 12.
Remove the burners from the cooking box.
Check fit around burner
Figure 14
Crossover tube
ƽCAUTION: If the Spider Stopper Guards do not fit
tightly, contact Weber-Stephen Customer Service.
k) Reconnect gas supply line. See “Check for gas leaks”.
Figure 12
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Crossover Ignition System Operations
If the Crossover Ignition System fails to ignite the Front
burner, light the Front burner with a match. If the Front
burner lights with a match, then check the Crossover
Ignition System.
■ Check that both the white and black ignition wires are
attached properly. Figure 15.
White wire
Black wire
Figure 15
■ Check that the Crossover Ignition button pushes the
igniter (button) down, and returns to the up position.
■ Check to see if the igniter is loose in the frame.
Tighten if necessary; see Step “Install igniter” for
correct procedure.
If the Crossover Ignition System still fails to light, See
Section "Manual Lighting", and contact Weber-Stephen
Customer Service.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Check
Cure
Burners burn with a yellow or orange
flame, in conjunction with the smell of gas.
Inspect Weber Spider Stopper
Guards for possible obstructions.
(Blockage of holes.)
Clean Weber Spider Stopper
Guards. (See Section "Annual
Maintenance".)
Burner does not light, or flame is low in HIGH
position.
Is natural gas supply on ?
Turn on natural gas supply.
Does the Front burner light with a
match?
If you can light the Front
burner with a match, then
check the Crossover Ignition
System.
Were natural gas lines purged?
(Air removed)
Purge the natural gas lines.
See Step “Purge air from gas
lines.”
Experiencing flare-ups:
Are you preheating barbecue in the All burners on high for 10 to
prescribed manner?
15 minutes for preheating.
Are the cooking grates and
Clean thoroughly. (See
Flavorizer Bars heavily coated with Section "Periodic Cleaning".)
burned-on grease?
Is the bottom tray "dirty" and not
allowing grease to flow into catch
pan?
Clean bottom tray.
ƽCAUTION: Do not line the bottom tray
with aluminum foil.
Are burners clean?
Clean burners. (See Section
"General Maintenance".)
Burner flame pattern is erratic. Flame is low
when burner is on HIGH. Flames do not run the
whole length of the burner tube.
The lid is porcelain-on-steel, not
paint. It cannot “peel.” What you are Section "Periodic Cleaning".)
seeing is baked on grease that has
Clean thoroughly. (See
Inside of lid appears to be “peeling.”
(Resembles paint peeling.)
turned to carbon and is flaking off.
THIS IS NOT A DEFECT.
If problems cannot be corrected by using these methods, please contact Weber-Stephen Customer Service.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
28
29
30
3
4
5
6
7
31
32
33
34
35
36
37
38
39
40
41
42
8
9
10
11
12
13
14
43
15, 16
17
18
52
44-48
9
49
50
51
19
20
21
22
26
27
23
24
25
17
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
All items are single quantities unless otherwise specified.
While we give much attention to our products,
unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call the Weber
Customer Service Center toll free 1-800-446-1071 to
receive immediate assistance. Have your owner’s manual
and serial number of the barbecue available for reference.
Parts can be ordered directly from Weber-Stephen
Products Company by phone or mail.
Note - Do not return parts to Weber-Stephen Products Co.
without first contacting the Customer Service Center by
phone or mail. Returning the part may not be necessary.
Weber-Stephen Products Company
Customer Service Center
250 South Hicks Road
Palatine, IL 60067-6241
(800) 446-1071
1
2
3
4
5
6
7
8
9
Lid (assembly)
Lid handle
28 Hair pin cotters (2)
29 Hinge pins (2)
30 Thermometer
31 1/4-20 keps nut
32 Cooking box
33 Burner control knobs (3)
34 Control panel
35 Igniter button
36 Phillips screws/washers (2)
37 Crossover tube
38 Front and back burners (2)
39 Center burner
Warm-Up Basket
Warming rack
Short Flavorizer bars (8)
Long Flavorizer bars (5)
Cooking grates (2)
Work table
Tubing plugs (3)
10 1/4-20 x 2 inch bolts (5)
11 Spacer bracket
12 End bracket
13 Left frame
40 1/4-20 stainless steel wing nuts (2)
41 Spider Stopper Guards (3)
42 Manifold assembly
43 Manifold bracket
44 Igniter
14 Condiment basket
15 1/4-20 x 1/2 inch bolts (6)
16 1/4 inch nylon washers (7)
17 Side panel (2)
18 Side frame (2)
19 Bottom tray
20 Catch pan holder
21 Catch pan
22 Drip pans (2)
45 Igniter lock nut
46 Gas catcher ignition chamber
47 Igniter wire (black)
48 Igniter wire (white)
49 Right frame
23 Accessory rack
24 Base panel
50 Gas supply line
51 Flare fitting
25 Tool holders (3)
26 Front panel
52 Control panel inserts (2)
27 Plastic buttons (10)
ƽWARNING:
Use only Weber factory authorized parts. The
use of any part that is not factory authorized
can be dangerous. This will also void your
warranty.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
A FINAL WORD
OF THANKS
hank you for choosing a Weber Barbecue.
T
Our family here at Weber has worked hard
to produce the highest quality products
for your satisfaction.
While we give much attention to our products, an
occasional error may occur. Our knowledgeable
Customer Service staff is prepared to help you
with any problems with parts or assembly.
Call our toll free number 1-800-446-1071.
For quicker service, please have your owner’s
manual available for reference. We also welcome
any comments or suggestions you might have
regarding our products.
We wish your family the
best in outdoor cooking enjoyment.
Weber-Stephen Products Company
Customer Service Center
200 East Daniels Road
Palatine, Illinois 60067-6266
Download from Www.Somanuals.com. All Manuals Search And Download.
|