DS-350 COMMERCIAL ROLL-UP DOORS
INSTALLATION INSTRUCTIONS
IMPORTANT NOTICE!!
Read the enclosed instructions carefully before attempting to install this door. Pay close
attention to all warnings and important safety notices.
This manual MUST be attached to the wall in close proximity of the door.
©Copyright 2002 Wayne-Dalton Corp.
P/N 291341, DOC #101-0093-1 REV 02
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
This manual's main function is to assist the installer in correctly mounting doors with due regard for safety,
operation, and sound construction practices. Reference must be made to construction codes in your area.
All Wayne-Dalton DS-350 Windload Rated Commercial Roll-Up Doors follow the general instructions contained
herein. Additional installation information for the specific door shipped is found with the packing slip and on
supplementary drawings. There are also bolt and small sealed parts bags with accessory lists, describing proper
application.
PREPARATION
Read the installation instructions thoroughly to become familiar with the names of the various components and their
relation to each other. It is necessary for the installer to determine the following:
° Method of operation (push-up, hand chain, or motor operated).
° Type of jamb (masonry or steel) on which the door mounting angles mount and the fasteners required.
° The dimensions for the opening width, opening height, headroom, and side room.
MATERIAL
Inspect your door for possible damage or shortage of parts. Report any shortages to your door supplier immediately,
or transit related damage claims to your freight carrier.
CLEARANCES
Check the door opening dimensions and available clearances versus the dimensions listed on the packing slip. Be
sure that the dimensions are correct for the opening you are working on, taking special note of the opening width
and height. Be sure that the required clearances listed on the Dimension Tables in this manual are available prior to
installation.
TOOLS
The tools recommended for proper installation of each door will vary, but commonly used tools are:
° Electric drill with 3/8" or 1/2" chuck with nut driver bits
° Masonry drill or impact hammer and bits.
° Chain hoist and sling for raising barrel and curtain assembly.
° Scaffolding, Mechanical Lift, and/or Ladders (ladders not recommended for larger doors).
° Hammer.
° Channel Lock Pliers
° Center punch.
° Screwdrivers.
° Drills.
° Wrenches, vise grips, C-clamps, torque wrench, and a large pipe wrench.
° Plumb line, tape measure, chalk line, and a water level.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 1 UNPACKING DOORS
Doors shipped by common carrier arrive at the job site packed in cardboard. Before removing the door from the
packaging, inspect the door and packaging for visible signs of damage. If damage is noted, file a freight claim with
the freight company immediately. Remove the door from the packaging.
Do not cut tape that holds door in a roll. You will be told in
step #7 when to cut tape.
No guarantee will be given by Wayne-Dalton Corp. if the door is not erected as instructed. For best operation, follow
the instructions step by step. Please review all instructions thoroughly before starting installation.
STEP 2 CHECK THE DOOR OPENING
Verify the opening measurements with the door packing slip. Consult the factory if the actual opening width varies
from that shown on the packing slip by more than 2 inches. Check door jambs, header, and floor for plumb/level
condition. Check that there is sufficient clearance at jambs and head (see Dimension Tables below).
Left hand operated door shown above. Right hand is opposite.
OPERATION
A
OPENING HEIGHT
UP TO 8’ HIGH
B
C
PUSH-UP
6”
9”
8”
20” 10”
DIRECT DRIVE CHAIN/MOTOR
REDUCED DRIVE CHAIN
FROM 8’ TO 10’ HIGH 22” 11”
OVER 10’ HIGH 24” 12”
DIMENSION TABLES - MINIMUM OVERHEAD CLEARANCE (B) INDICATED
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 INSTALLING MOUNTING ANGLES AND GUIDES
Obtain the appropriate Bolt Line (BL) measurement from the chart below. Use Opening Width listed on packing
slip. Any variation between the actual opening width and the width listed on the packing slip is to be ignored.
OPENING WIDTH
BL
BL
ANGLE FACE TO ANGLE FACE
(STEEL) (MASONRY)
UP TO 10’ WIDE
OVER 10’ WIDE
1-9/16”
1-7/16”
4-15/16”
4-7/8”
OPENING WIDTH + 6-11/16”
OPENING WIDTH + 6-7/16”
Use BL measurement to locate wall mounting angle for one
jamb only. Second angle will be located using Angle Face to
Angle Face measurement.
Using the BL measurement, loosely
clamp the right hand wall angle to the
right hand jamb. Position the wall angle
such that the BL measurement falls near
the center of the slots. Adjust the wall
angle so that it is level and tighten the
clamp. Install wall angle fasteners in the
centers of the top and bottom slots only
and tighten.
Select the appropriate Angle Face to
Angle Face equation from the chart
above. Add the opening width listed on
the packing slip to obtain the Angle
Face to Angle Face measurement. Use
this measurement to locate the left hand
wall angle on the left hand jamb and clamp in place. Install the top and bottom bolts in the wall angle. Verify that
both wall angles are level and double check the angle to angle measurement at the top, middle, and bottom to ensure
that the wall angles are properly located. Using a string and a level, ensure that the mounting angles are parallel to
each other, shimming if necessary, to achieve both vertical and horizontal leveling. Now install the remaining bolts
in both wall angles.
Angle Face to Angle Face measurement
must be held to ensure proper door
operation and resistance to windload.
Use of any other fasteners than those
provided must be approved by
manufacturer or building authority and
cannot be of lesser diameter or grade.
Align the guide slots with the slots in the wall angles and fasten guides with the interior
windlock return towards the door jamb using the 5/16-18 x 5/8” truss head bolts,
washers, and flange nuts. Slide guides to set the “H” dimension as shown above at 1-3/4”
prior to tightening the guide fasteners.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Trim the top of each wear strip at a 45° angle as shown and clip onto the appropriate
leg of each guide. Be sure that trimmed edges of the wear strips end just below the
flare of the guides. Install the bottom bar stops with the same 5/16-18 x 5/8” truss
head bolts and flange nuts used to assemble the guides (no washer). Leave the
fasteners loose to allow the bottom bar stops to pivot out of the wayof the bottom bar
angle when the curtain will be pulled into the guides. You will be instructed to
tighten the bottom bar stop fasteners in step #7.
STEP 4 INSTALL BRACKETS AND DRIVE COMPONENTS
From the Dimension Tables on page 4, mark the width location of each bracket by using dimension A for the
operator side and 6” for the non-operator side. If the actual opening width varies from the packing slip width, adjust
these dimensions by adding or subtracting ½ of the difference to each dimension. Subtract if the opening is larger
and add if smaller. Mark the height location of the brackets by using dimension C. Verify the ceiling clearance
minimum from dimension B. Use a string and a level to verify that the brackets are level with each other. Adjust
bracket height as needed to level. Drill anchor holes and fasten the brackets with the anchors provided.
Brackets must be level to each other with respect to height.
Failure to level bracket heights will prevent door from
operating properly.
If the door is to be chain hoist or motor operated, install the components shown below to the operator side of the
curtain at this time using the fasteners provided. Do not tighten set screws at this time, you will be instructed to
tighten these in step #9.
Keep loose clothing, fingers, hands and arms away from all
moving mechanisms, or serious injury or death could result.
WARNING
STEP 5 LIFTING THE DOOR ASSEMBLY
Door assembly is extremely heavy. Do not allow door
assembly to fall from lifting mechanism, or serious injury or
WARNING
death could result.
Lift door assembly up to door support brackets. Care should be taken to avoid any damage to the curtain. Make sure
that the door assembly is centered between the guides and that clearance between the windlocks and the guides is the
same on both sides. Adjust door assembly location as needed. Place the axle saddle castings under the axle on each
6
Download from Www.Somanuals.com. All Manuals Search And Download.
side and position the door as close as possible to the door header. Be sure that the door is able to revolve without
scraping against door header or guides. Rotate door assembly so that bottom bar angle is at bottom of curtain roll.
To avoid serious injury or death, never walk, stand, or work
below door assembly before it is secured to support brackets.
WARNING
STEP 6 SECURE AXLE SADDLE CASTINGS
Making sure that the bottom bar angle is at the bottom of the
curtain roll; place the axle saddle castings around the axle on each
side, with the flat keeper plate on top. Install the 3/8-24 x 3-1/2”
bolts, flat and lock washers, and 3/8-24 nuts as shown. Be certain
to tighten both nuts to a torque of 40 foot-pounds. Spring tension
will be lost if both axle saddles are not tightly secured.
Axle saddles hold extreme spring tension. Loose axle saddles
could result in loss of spring tension, causing door to fall,
possibly producing serious injury or death.
WARNING
STEP 7 PRE-TENSION THE DOOR SPRINGS
Starting with the bottom bar angle at the bottom of the curtain roll, apply two complete
turns of pretension to the springs by rotating the curtain roll in the direction shown. The
amount of tension required may vary slightly. Final adjustment, if necessary, will be made
in Step #10.
Spring tension can cause curtain roll to rotate rapidly.
Securely hold curtain roll from rotating while applying
pretension or serious injury or death could result.
WARNING
Securely hold door curtain until bottom bar stop fasteners
have been tightened. If not securely held, door may raise or
drop, possibly causing injury or death.
WARNING
Do not apply pretension to larger
doors using ladders. Ladders may fall
causing serious injury or death.
WARNING
Cut the tape that holds the door in a roll and gently pull the curtain down into the
guides on both sides until the bottom bar is below the bottom bar stops. Do not pry on
the bottom bar stops to get bottom bar past, loosen fasteners until bottom bar angle
easily clears stops. If the door has a tendency to close, secure in position using clamps.
If the door has a tendency to rise, secure in position using a wood prop as shown.
While the door is secured from moving, tighten the bottom bar stop fasteners on both
guide assemblies.
Tighten bottom bar stop fasteners with impact gun
to prevent bolts from spinning.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 INSTALL SLIDE BOLT LOCKS
Install slide bolt locks, if provided,
as shown.
Install the lift handle to bottom bar
angle at this time.
STEP 9 LUBRICATE AND ADJUST THE GUIDES
Lubricate the insides of the guides and wearstrips with weather resistant lubricating spray. Be sure to spraylubricant
over the flares at the tops of the guides. Move the door up and down to check for proper operation. Adjust the guides
and mounting angles if necessary to allow for proper clearance and operation.
If door is difficult to move up and/or down due to spring imbalance,
continue on to step #10 and return to step #9 once springs are properly
adjusted.
STEP 10 CHECK AND ADJUST SPRING BALANCE
It is strongly recommended that two or more installers perform
this next step.
Never remove bottom bar stops when adjusting tension,
otherwise, door can spin uncontrollably resulting in serious
injury or death.
WARNING
If the door lowers easily and raises hard, more spring tension is required. If the door lowers hard and raises easily,
less spring tension is required. Before adjusting the spring tension, be sure that the door is in the full up position.
Secure the door in the full up position to prevent the door from falling if the adjustment wrench slips. Use one of
these methods:
•
•
Tie a rope around the door roll and bottom bar angle.
Place a clamp on guides holding the door securely at the stops.
Always stand to one side of wrench when adjusting tension.
Never adjust tension with wrench in front of/above you. This
will help avoid serious injury if you lose control of wrench.
WARNING
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Place a large pipe wrench in position on the door axle as shown and slightly
loosen both axle saddle castings. Pull down on the wrench for more spring
tension and let up on the wrench for less spring tension.
As saddle castings are
loosened, hold wrench securely.
WARNING
Springs are very strong and can
cause serious injury if not controlled properly.
Tighten both axle saddle castings per Step #6 while holding the pipe wrench
firmly to maintain desired adjustment. Let off the pipe wrench tension only
after the nuts on both axle saddle castings are tightened back to 40 foot-pounds.
When removing pipe wrench from axle, slowly reduce applied
tension until wrench is free from axle. This will help avoid
serious injury in event that saddle castings have not been
tightened sufficiently.
WARNING
Test the door as in Step #9 above. Repeat the above procedure if further adjustments are required. Once all
adjustments have been made and the door is operating properly, recheck all fasteners and bolted connections to
ensure that they are in place and properly tightened. Tighten all set screws in the components installed in step #4.
STEP 11 INSTALLATION OF TOP DRAFT STOP
Close the door and secure it in the down
position. Use a pencil to mark the door panel
corrugation that is parallel with the bottom of
the header/lintel from the outside of the
opening. If this corrugation protrudes below the
header, mark the one just above. Open the door
until the marked corrugation is accessible.
Stretch the top draft stop across the door and
attach it to the curtain on the marked
corrugation with the #8 x ½” self-drilling
screws provided, locating the screws every 12"
on center. Trim the Top Draft Stop to clear the
guides if required. When the door is closed, the
draft-stop should seal on the header.
Top Draft Stop may not seal on header if not installed on a corrugation as
shown.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
REDUCED DRIVE CHAIN HOIST INSTALLATION INSTRUCTIONS (if applicable)
STEP 12 ALIGN THE SPROCKETS
Feed the hand chain through the pocket wheel assembly (installed in step #4),
around the cast iron hand chain wheel, and connect the two end links.
Align the chain hoist so that the 41B9 sprocket on the pocket wheel assembly is
in line with the 41A40 sprocket bolted to the barrel. Next, tighten the hoist-
locking bolts to lock the pocket wheel assembly to the shaft to prevent it from
shifting or rocking.
Hoist locking bolts must be tight to ensure hoist cannot shift
and permit roller chain to come off, thereby allowing door to
drop possibly causing severe injury or death.
WARNING
Next, connect the #41 roller chain between the pocket wheel assemblysprocket and the barrel sprocket. Now run the
door up and down several times to ensure that the roller chain does not come off. If it does, go back and check the
alignment of the sprockets.
Keep loose clothing, fingers, hands, and arms away from all
moving mechanisms and places where chain meets either
sprocket, or serious injury or death could result.
WARNING
STEP 13 INSTALL THE CHAIN KEEPER
Now install the hand chain keeper to the wall
approximately four feet above the finished floor with the
hardware provided. Refer to the figure in step #7 of this
manual for an additional view.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
1
Description
Item
18
19
20
21
22
23
24
25
26
27
28
29
30
Description
Top Sheets - Give Length
1/4-20 x 1” Slotted Screw, Washer & Nylon Nut
Mounting Angle, Give Mounting Condition, Give Length
Direct Drive Chain Wheel
2
Intermediate Sheets - Give Length
Bottom Sheet Assembly - Give Length
Guide, Left Hand or Right Hand (Right Hand Shown)
Axle - Give Length
3
4
Chain Retainer Clip
5
Direct Drive Chain Guide
6
Drum Assembly
1/2" Collar (Not Shown)
7
Spring - Right - Give Length & Wire Diameter
Spring - Left - Give Length & Wire Diameter
Spring Clip
5/16” Polypropylene Rope
8
Electric Operator Sprocket
9
Electric Operator Mounting Bracket
Electric Operator 3/8” x 3” Bolt & Tube
Drum Bearing
10
11
12
13
14
15
16
17
Left Mounting Bracket – Based on Door Size - Give Type
Right Mounting Bracket – Based on Door Size – Give Type
Axle Saddle
Bottom Bar Stop, 5/16-18 x 5/8” THMS & Flange Nuts
Lift Handle (center mounted)
Keeper Plate
3/8-24 x 3½” Axle Bolt + Washer, Lock Washer, & 3/8” Nut 31
3/8” x 5” Wedge Anchor
Lift Clip - Edge Mounted
Spacer Nut
32
33
5/16-12 x 1” Self-Drilling Screw and Washer
Guide Fasteners, 5/16-18 x 5/8” THMS, Washers & Nuts
Slide Bolt Lock
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Roll-Up Sheet Door
LIMITED WARRANTY
Wayne-Dalton Corp
P.O. Box 67- Mt. Hope, Ohio 44660
The Manufacturer warrants the ROLL-UP SHEET DOOR and hardware fittings for a period of ONE YEAR from the time of
delivery against any defects in workmanship or material. Manufacturer shall, upon notification, correct such nonconformity at its option, by
repairing or replacing any defective part or parts.
NO EMPLOYEE, DISTRIBUTOR, OR REPRESENTATIVE IS AUTHORIZED TO CHANGE THE FOREGOING
WARRANTIES IN ANY WAY OR GRANT ANY OTHER WARRANTY ON BEHALF OF MANUFACTURER.
The Manufacturer shall not be responsible for any damage resulting to or caused by its products by reason of installation, improper
storage, unauthorized service, alteration of products, neglect or abuse, or attempt to use the products for other than the customary usage or
for their intended purposes. The ROLL-UP SHEET DOOR warranty becomes null and void if other than Manufacturer’s specified holes are
drilled. The above warranty does not cover wear or any damage beyond Manufacturer’s control or replacement labor.
THIS WARRANTY COVERS A COMMERCIAL PRODUCT, THE FOREGOING WARRANTIES ARE IN LIEU OF ALL
OTHER WARRANTIES AND NO REPRESENTATIONS, GUARANTEES, OR WARRANTIES, EXPRESSED OR IMPLIED,
(INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE), ARE MADE BY MANUFACTURER IN CONNECTION WITH MANUFACTURE OR SALE OF ITS PRODUCTS.
Claims for defects in material and workmanship covered by this warranty shall be made in writing to the dealer from whom the
product was purchased within the warranty period. Manufacturer may either send a service representative or have the product returned to the
Manufacturer at Buyer’s expense for inspection. If judged by Manufacturer to be defective in material or workmanship, the product will be
replaced or repaired at the option of Manufacturer, free from all charges except authorized transportation and replacement labor.
THE REMEDIES OF BUYER SET FORTH HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER REMEDIES.
THE LIABILITY OF MANUFACTURER, WHETHER IN CONTRACT, TORT, UNDER ANY WARRANTY, OR OTHERWISE,
SHALL NOT EXTEND BEYOND ITS OBLIGATION TO REPAIR OR REPLACE, AT ITS OPTION, ANY PRODUCT OR PART
FOUND BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP. MANUFACTURER SHALL NOT BE
LIABLE FOR COST OF REMOVAL OR INSTALLATION OR SHALL NOT BE RESPONSIBLE FOR ANY DIRECT, INDIRECT,
SPECIAL, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
This warranty gives you specific legal rights which may vary from state to state. However, some states do not allow limitations on
how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or
exclusions may not apply to you.
Wayne-Dalton Corporation
Door & Systems Division
2589 County Road 168
Dundee, OH 44624
1-800-795-5095
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|