Wagner SprayTech Paint Sprayer 9146 User Manual

Models 9140S, 9146, 9150, 9170 and 9190  
Owner’s manual: Read this manual for complete instructions  
Table of Contents  
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3  
Components and Description . . . . . . . . . . . . . . . .4-5  
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Purging and Priming the Sprayer . . . . . . . . . . . . . . .8  
Purging and Priming the Spray Hose . . . . . . . . . . .9  
Practice / Spraying Technique . . . . . . . . . . . . . . . .10  
Spraying Troubleshooting . . . . . . . . . . . . . . . . .11-12  
Unclogging the Spray Tip . . . . . . . . . . . . . . . .11  
Cleaning the Spray Gun Filter . . . . . . . . . . . . .12  
Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-17  
Cleanup for Oil-based materials . . . . . . . . . . .15  
Cleaning the Suction Set . . . . . . . . . . . . . . . . .16  
Cleaning the Spray Gun Components . . . . . .17  
Short-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . .18  
Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . .19  
Cleaning the Inlet Valve . . . . . . . . . . . . . . . . . . . . . .20  
Fluid Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
Troubleshooting / Maintenance . . . . . . . . . . . . . . .22  
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45  
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67-70  
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71  
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72  
This pump is available in a stand model (9140S) and cart models (9146,  
9150, 9170 and 9190). All information given for the stand model applies  
to the cart models except where indicated.  
1-800-880-0993  
Need Help? Call us first for answers  
fast. Call Wagner Spray Tech toll-free if you  
have any comments or problems with this product.  
Wagner Technical Service  
Visit us on the world wide web!  
1770 Fernbrook Lane, Plymouth, MN 55447  
Technical service hours: Monday through Friday, 8:00 am to 4:30 pm Central Time  
0606 • Form No. 0516927B  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Information • Read all safety information before  
operating the equipment. Save these instructions  
HAZARD: GENERAL  
NOTICE  
Can cause severe injury or property damage.  
THE 9140S, 9146 AND 9150 SERIES UNITS ARE PROVIDED WITH A  
NON-RESETABLE THERMAL OVERLOAD. THE 9170 AND 9190  
SERIES UNITS ARE PROVIDED WITH A REPLACEABLE FUSE.  
PREVENTION:  
• Read all instructions and safety precautions before operating  
equipment.  
• Always disconnect the motor from the power supply before working  
on the equipment.  
• Follow all appropriate local, state, and national codes governing  
ventilation, fire prevention, and operation.  
The cause of the overload should be corrected before  
restarting. Take unit to Service Center.  
• The United States Government Safety Standards have been  
adopted under the Occupational Safety and Health Act (OSHA).  
These standards, particularly part 1910 of the General Standards  
and part 1926 of the Construction Standards should be consulted.  
• Use only manufacturer authorized parts. User assumes all risks  
and liabilities when using parts that do not meet the minimum  
specifications and safety requirements of the pump manufacturer.  
Grounding Instructions  
This product must be grounded. In the event of an electrical short  
circuit, grounding reduces the risk of electric shock by providing an  
escape wire for the electric current. This product is equipped with a  
cord having a grounding wire with an appropriate grounding plug. The  
plug must be plugged into an outlet that is properly installed and  
grounded in accordance with all local codes and ordinances.  
• Before each use, check all hoses for cuts, leaks, abrasion or  
bulging of cover. Check for damage or movement of couplings.  
Immediately replace the hose if any of these conditions exist.  
Never repair a paint hose. Replace it with another grounded high-  
pressure hose.  
• All hoses, swivels, guns, and accessories must be pressure rated  
at or above 3000 PSI/207 BAR.  
• Do not spray outdoors on windy days.  
WARNING  
• Wear clothing to keep paint off skin and hair.  
Improper installation of the grounding plug can  
result in a risk of electric shock.  
• Do not operate or spray near children. Keep children away from  
the equipment at all times.  
If repair or replacement of the cord or plug is necessary, do not connect  
the green grounding wire to either flat blade terminal. The wire with  
insulation having a green outer surface with or without yellow stripes is  
the grounding wire and must be connected to the grounding pin.  
• Do not overreach or stand on an unstable support. Keep effective  
footing and balance at all times.  
• Stay alert and watch what you are doing.  
• Do not operate the unit when fatigued or under the influence of  
drugs or alcohol.  
Check with a qualified electrician or serviceman if the grounding  
instructions are not completely understood, or if you are in doubt as to  
whether the product is properly grounded. Do not modify the plug  
provided. If the plug will not fit the outlet, have the proper outlet  
installed by a qualified electrician.  
This product is for use on a nominal 120 volt circuit and has a  
grounding plug that looks like the plug illustrated below. Make sure that  
the product is connected to an outlet having the same configuration as  
the plug. No adapter should be used with this product.  
Important Electrical Information  
NOTICE  
Use only a 3-wire extension cord that has a 3-blade grounding plug and  
a 3-slot receptacle that will accept the plug on the product. Make sure  
your extension cord is in good condition. When using an extension  
cord, be sure to use one heavy enough to carry the current your  
product will draw. An undersized cord will cause a drop in line voltage  
resulting in loss of power and overheating. A 14 or 12 gauge cord is  
recommended (see chart below). If an extension cord is to be used  
outdoors, it must be marked with the suffix W-A after the cord type  
designation. For example, a designation of SJTW-A would indicate that  
the cord would be appropriate for outdoor use.  
Grounded Outlet  
Grounding Pin  
Cover for grounded outlet box  
If you experience problems with your  
sprayer at any time during assembly,  
operation, or cleanup, please refer to  
the Troubleshooting section of this  
manual (page 22), or call customer  
service at:  
Cord gauge  
Maximum cord length  
200 feet  
12  
14  
100 feet  
Do not use more than 100 feet of spray hose. If you need to  
spray further than 100 feet from your power source, use  
more extension cord, not more spray hose.  
1-800-880-0993  
3
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Components and Description  
Components  
The shipping carton for your painting system contains the following:  
• Suction tube and return tube  
• Separating Oil  
• Pump cleaning adapter  
• Instruction manual  
• Spray gun with filter  
• Hose bracket (all cart units)  
• Pail bracket (all cart units)  
• Spray tip assembly (see chart on next page)  
• 25’ (9140S, 9146, 9150) or 50’ (9170, 9190), 1/4” diameter pressure hose  
Controls and Functions  
ON/OFF Switch. . . . . . . . . . . The ON/OFF switch turns the power to the sprayer on and off (O=OFF, l=ON).  
Suction tube . . . . . . . . . . . . . Fluid is drawn through the suction tube into the pump.  
Fluid Section . . . . . . . . . . . . A piston in the fluid section moves up and down to create the suction that draws fluid through the  
suction tube.  
Spray Gun. . . . . . . . . . . . . . . The spray gun controls the delivery of the fluid being pumped. The gun model you have depends on  
Spray Hose . . . . . . . . . . . . . . The spray hose connects the gun to the pump.  
Return Tube . . . . . . . . . . . . . Fluid is sent back out through the return tube to the original container when PRIME/SPRAY knob is in  
PRIME position.  
Pump Cleaning Adapter . . . The adapter allows you to attach a garden hose to the suction tube for easy cleanup (latex materials  
only).  
PRIME/SPRAY Knob . . . . . . The PRIME/SPRAY knob directs fluid to the spray hose when set to SPRAY or the return tube when set  
to PRIME. The arrows on the PRIME/SPRAY knob shows the rotation directions for PRIME and  
SPRAY.  
The PRIME/SPRAY knob is also used to relieve pressure built up in the spray hose (see Pressure  
Pressure Control Dial . . . . . The pressure control dial regulates the amount of force the pump uses to push the fluid.  
Oiler. . . . . . . . . . . . . . . . . . . . (9146, 9150, 9170, 9190 only) The oiler is designed to provide lubrication to the fluid section of the  
pump.  
Pusher Stem. . . . . . . . . . . . . The pusher stem is designed to keep the inlet valve open and from sticking due to dried materials.  
Specifications  
Capacity  
9140S .......................Up to .25 gallon (0.95 liter) / minute  
Generator power  
requirement.....................8000 Watt  
9146, 9150................Up to .29 gallon (1.10 liters) / minute  
9170 .........................Up to .33 gallon (1.25 liters) / minute  
9190..........................Up to .42 gallon (1.60 liters) / minute  
Safety features................Spray gun trigger lock and pressure  
diffuser; built-in tip safety guard;  
PRIME/SPRAY knob for safe pressure  
release.  
Power source  
Capability ........................Sprays a variety of paints, oil base  
latex, primers, stains, preservatives  
and other nonabrasive materials,  
including pesticides and liquid  
9140S .......................1/2 Hp universal motor  
9146, 9150................5/8 Hp universal motor  
9170..........................3/4 Hp permanent magnet DC motor  
9190 .........................7/8 Hp permanent magnet DC motor  
fertilizers.  
This pump should not be used with  
textured materials, block filler, or  
asphalt sealer.  
Power requirement.........15 amp minimum circuit on 115 VAC,  
60 Hz current  
4
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Components and Description  
This pump is available in two models: a stand model (9140S) and cart models (9146, 9150 shown below, 9170 and 9190). All  
information given for the stand model applies to the cart models except where indicated.  
Important  
Some of the graphics in this manual may not exactly match your sprayer and spray gun. All information and instructions  
given in this manual applies to all models except where noted.  
9140S  
9146, 9150  
9170  
GX-05  
GX-07  
GX-07  
GX-08  
415  
415  
517  
517  
415  
517  
519  
521  
Yellow (fine)  
Yellow (fine)  
White (medium)  
White (medium)  
25 feet  
25 feet  
50 feet  
50 feet  
9190  
Hose bracket  
Spray hose  
Pressure control dial  
(rear of sprayer)  
Oiler (9146, 9150,  
9170 and 9190only)  
Spray hose port  
(reverse side)  
ON / OFF switch*  
(reverse side)  
PRIME/SPRAY  
knob  
Pail bracket  
Pusher stem  
Return tube  
fitting  
Return tube  
Suction tube  
**The pump cleaning  
adapter can be clipped  
to the spray hose port  
Spray gun (see chart above  
for models, GX-07 shown)  
Clip  
Suction set filter  
Spray  
guard  
Pump cleaning  
adapter**  
Spray tip  
(see chart above  
for models)  
5
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Assembly  
Do not plug in the sprayer until setup is complete.  
WARNING  
Tools needed for assembly:  
• Two adjustable wrenches  
• Extension cord (refer to Important Electical  
Information (page 3).  
• 3/16” Allen wrench  
If you have one of the cart models (9146, 9150, 9170 or 9190), follow these assembly instructions. If you have the model  
9140S sprayer, skip to item 4, below.  
1. Twist the knobs on either side of the  
handle counterclockwise to unlock  
the handle. Pull the handle out fully,  
and turn knobs clockwise to lock  
into place.  
2. Insert the ends of the hose bracket  
into the holes of the handle as  
shown.  
3. Attach the pail bracket. Line up the  
holes in the bracket with the holes in  
the sprayer. Insert and tighten the  
screws using a 3/16” allen wrench.  
5. Thread the other end of the hose to the spray gun. Hold  
the gun with one adjustable wrench, and tighten the hose  
nut with the other.  
4. Thread the high pressure hose to the spray hose port.  
Tighten with an adjustable wrench.  
The spray tip SHOULD NOT  
be attached until after the  
sprayer and spray hose have  
been purged and primed.  
6. Remove cap from inlet  
valve (a). Thread the  
suction tube onto the  
inlet valve and tighten  
firmly by hand. Be  
7. Press the return  
8. Verify that the seal is  
present inside the  
suction tube. Thread  
the inlet filter into the  
end of the suction  
tube.  
tube onto the  
return tube fitting.  
Squeeze clip  
over the return  
tube fitting to  
secure the return  
tube.  
sure that the threads  
are straight so that the  
fitting turns freely.  
(a)  
6
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This section contains instructions that will be repeated  
throughout this manual.  
Before you begin -  
Locking the Spray Gun:  
Always lock the trigger off when attaching the spray tip or when the spray gun is not in use.  
WARNING  
Model GX-05 and GX-07 Spray Gun  
Model GX-08 Spray Gun  
The gun is locked when the trigger lock is at a 90º  
angle (perpendicular to the trigger in either direction).  
To lock the gun, turn the trigger lock forward and  
slightly down until it stops.  
GX-05  
GX-07  
Plugging in the Sprayer:  
2. Plug the power cord into a grounded outlet or heavy duty  
grounded extension cord. Plug in the extension cord.  
Refer to Important Electrical Information, page 3.  
1. Check that the ON/OFF switch is in the OFF (O) position.  
Pressure Relief Procedure:  
Be sure to follow the Pressure Relief Procedure when shutting the unit off FOR ANY PURPOSE.  
This procedure is used to relieve pressure from the spray hose.  
WARNING  
1. Lock the spray gun off (see  
directions above). Move the  
ON/OFF switch to the OFF position.  
2. Turn the PRIME/SPRAY knob to  
PRIME.  
3. Unlock the spray gun and trigger  
spray gun into the side of the  
material bucket. Lock the spray  
gun.  
7
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Purging and Priming the Sprayer  
All new units are performance-tested at the factory and are shipped with test fluid in the fluid section to prevent  
corrosion during shipment and storage. If you have already used your pump, some water or solvent used in cleaning  
may remain in the fluid section. Whether your sprayer is new or if you have already used it, this fluid must be purged  
and thoroughly cleaned out of the system prior to use. Follow the steps below.  
9146, 9150, 9170 and 9190 only.  
1. Remove oiler cap using a straight-  
slot screwdriver. Squirt separating  
oil (P/N 0516913) supplied with your  
sprayer into the oiler. Light  
2. After filling, push button on front of  
face plate 2-5 times to lubricate the  
fluid section. Afterwards, press  
once for every eight hours of usage.  
Be sure to periodically check  
reservoir level (a) and refill as  
necessary.  
3. Fully depress the pusher stem to  
make sure the inlet ball is free.  
household oil can be substituted if  
necessary. Replace cap.  
(a)  
4. Place a full container of spraying material underneath the  
suction tube (a). Secure the return tube (b) into a waste  
container.  
5. Turn the pressure control dial to maximum pressure (+).  
Turn the PRIME/SPRAY knob to PRIME.  
(a)  
(b)  
7. Switch the pump OFF (O). Remove the return tube from  
the waste container and place it in its operating position  
above the container of spraying material. Use the metal  
clip to bind the two hoses together.  
6. Plug in the sprayer and move the ON/OFF switch to the  
ON (l) position.  
The unit will begin to draw material up the suction tube,  
into the pump, and out the return tube. Let the unit cycle  
long enough to remove test fluid from the pump, or until  
spray material is flowing from the return tube.  
8
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Purging and Priming the Spray Hose  
2. PULL the trigger and aim the spray gun at the side wall of  
1. Unlock the spray gun and turn the PRIME/SPRAY knob to  
a waste container. If using oil-based materials, the  
spray gun must be grounded while purging (see  
warning below).  
PRIME.  
The spray tip SHOULD NOT  
be attached to the spray  
gun when purging the  
spray hose.  
Keep hands clear from fluid stream.  
Ground the gun by holding it against the edge of a metal container while flushing.  
Failure to do so may lead to a static electric discharge which may cause a fire.  
WARNING  
3. While pulling the trigger, switch the pump ON (l), AND turn the PRIME/SPRAY knob to SPRAY. Hold the trigger until all air,  
water, or solvent is purged from the spray hose and material is flowing freely.  
SPRAY  
WARNING  
P R I M E  
If the PRIME/SPRAY knob is still on SPRAY, there  
will be high pressure in the hose and spray gun  
until the PRIME/SPRAY knob is turned to PRIME.  
4. Release trigger. Turn the PRIME/SPRAY knob to PRIME.  
Turn the pump OFF (O). Trigger the gun into the waste  
container to be sure that no pressure is left in the hose.  
5. Lock the spray gun off. Thread the spray tip guard  
assembly onto the gun. Tighten by hand.  
Begin  
tightening  
the tip at  
this angle  
. . .to achieve  
the desired  
spray angle  
when tight.  
9
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Practice / Spraying Technique  
NOTE - Be sure that the paint hose is free of kinks and clear of objects with sharp cutting edges.  
2. When motor shuts off, unlock the spray gun and spray a  
1. Switch the pump ON (l). Turn the PRIME/SPRAY knob to  
SPRAY. Turn the pressure control dial to maximum  
pressure (+). The spray hose should stiffen as paint  
begins to flow through it.  
test area to check the spray pattern.  
The motor will cycle on and off automatically as the pump  
needs pressure.  
The pressure control dial can be be adjusted up or down  
to achieve the desired spray pattern.  
SPRAY  
R P I M E  
Good spray pattern  
Paint tailing pattern  
(pressure too low,  
clogged tip)  
The key to a good job is an even coating over the entire surface. This is done by using even strokes. Follow the TIPS,  
below.  
Light Coat  
Heavy Coat  
Light Coat  
Keep the spray gun at right angles to the  
surface. This means moving your entire  
arm back and forth rather than just flexing  
your wrist.  
Tip:  
Approximately  
10 to 12 inches  
Wrong way  
Keep the spray gun perpendicular to the  
surface, otherwise one end of the pattern  
will be thicker than the other.  
Right way  
Tip:  
Tip:  
Trigger gun after starting the stroke. Release  
the trigger before ending the stroke. The  
spray gun should be moving when the trigger  
is pulled and released. Overlap each  
stroke by about 30%. This will ensure an  
even coating.  
Keep stroke  
even  
Approximately  
10 to 12 inches  
If you expect to be away from your sprayer for more than  
one hour, follow the Short-Term Storage instructions  
(page 18).  
Start  
Pull  
Move  
steadily  
Release  
trigger  
End  
stroke  
stroke trigger  
10  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Spraying Troubleshooting - Unclogging the Spray Tip  
If the spray pattern becomes distorted or stops completely while the gun is triggered, follow these steps.  
Do not attempt to unclog or clean the tip with your finger.  
WARNING  
NOTE - Do not use a needle or other sharp pointed instrument to clean the tip. The hard tungsten carbide can chip.  
1. Release the trigger and lock the gun off (see page 7).  
Rotate the reversible tip arrow 180º so that the point of  
the arrow is toward the rear of the gun (CLEAN position).  
GX-05 / GX-07  
Under pressure, the spray tip may be very difficult to  
GX-08  
turn. Turn the PRIME/SPRAY knob to PRIME and  
trigger the gun. This will relieve pressure and the tip  
will turn more easily.  
SPRAY  
2. Turn the PRIME/SPRAY knob to SPRAY.  
P R I M E  
3. Unlock the gun and squeeze the trigger, pointing the gun  
at a scrap piece of wood or cardboard. This allows  
pressure in the spray hose to blow out the obstruction.  
When the nozzle is clean, material will come out in a  
straight, high pressure stream.  
If material still will not spray from the spray tip, follow  
the Cleaning the spray gun filter instructions, page 12.  
Gun locked  
(see page 7)  
GX-05 / GX-07  
4. Release the trigger and lock the gun off (see page 7).  
Reverse the tip so the arrow points forward again (SPRAY  
position). Unlock the gun and resume spraying.  
GX-08  
11  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Spraying Troubleshooting - Cleaning the Spray Gun Filter  
The filter must be cleaned every time you use your sprayer. When using thicker spray materials, the filter might need to  
be cleaned more often.  
Spray gun model  
GX-07  
2a. Model GX-07 - Unscrew the fitting from the bottom of the  
Tapered  
end  
(filter top)  
spray gun using an adjustable wrench, making sure not to  
lose the spring.  
Filter  
Hole  
2b. Models GX-05 and GX-08 - Unclip the trigger guard from  
the filter housing by pulling outward from the filter  
housing. Unscrew the filter housing.  
Spring  
Fitting  
3. Remove the filter from the spray gun housing and clean  
with the appropriate cleaning solution (warm, soapy water  
for latex paints, mineral spirits for oil-based materials).  
4. Inspect the filter for holes (see inset, right). Replace if  
holes are found.  
Spray gun models  
GX-05 and GX-08  
NOTE - NEVER POKE THE FILTER WITH A SHARP  
INSTRUMENT!  
Tapered  
end  
(filter top)  
5. Replace the cleaned filter, tapered end first, into the gun  
housing. The tapered end of the filter must be loaded  
properly into the gun. Improper assembly will result  
in a plugged tip or no flow from the gun.  
Hole  
6. Reassemble the spray gun.  
Filter  
housing  
Trigger  
guard  
Filter  
Spraying Troubleshooting - Cleaning the Inlet Filter  
The filter at the bottom of the suction tube may also need cleaning. Check it every time you change spray containers.  
1. Remove the filter by unscrewing it from the suction tube.  
Clean the filter with the appropriate cleaning solution  
(warm, soapy water for latex materials, mineral spirits for  
oil-based materials).  
2. Thread the filter back into place.  
If after completing all of the steps in Spraying  
Troubleshooting you are still experiencing problems  
spraying, refer to the Troubleshooting section (page 22).  
12  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Important Cleaning Notes!  
Read these notes and warnings before you start to clean your sprayer!  
• When using latex materials, clean your sprayer and  
components with water. When using oil-based materials,  
use mineral spirits.  
WARNING  
Special cleaning instructions for use with flammable solvents:  
• Do not use mineral spirits on latex materials, or the  
ALWAYS FLUSH SPRAY GUN AT LEAST ONE HOSE  
mixture will turn into a jelly-like substance which is  
LENGTH AWAY FROM SPRAY PUMP.  
difficult to remove.  
• If collecting flushed solvents in one gallon metal  
container, place it into an empty five gallon container,  
then flush.  
• No matter which cleaning solution you use, make sure to  
dispose of it properly when finished cleaning your sprayer.  
• Area must be free from vapors.  
• Thorough cleaning and lubrication of the sprayer is the  
most important step you can take to ensure proper  
operation after storage.  
• Follow all cleanup instructions.  
• DO NOT USE GASOLINE TO CLEAN YOUR SPRAYER.  
Call 1-800-880-0993 if you have any problems or questions regarding the cleaning of your sprayer.  
Cleanup - Latex materials  
Follow these steps if you used latex materials AND if you have a garden hose available. If you do not have a garden  
hose available, follow the Cleanup - Oil-Based Materials instructions.  
1. Lock the gun and remove the spray tip assembly. Place  
the suction tube and return tube into an empty waste  
container.  
2. Using a garden hose, rinse off the suction tube, return  
tube and inlet filter. Empty the waste container.  
Empty waste  
container  
4. Verify that the seal is  
present inside the  
3. Remove the inlet filter from the suction tube and place  
into the waste container.  
adapter (a) Thread the  
pump cleaning adapter  
(d)  
(b) onto a garden hose  
(c). Connect hose and  
adapter to the fitting on  
the end of the suction  
tube (d).  
(b)  
(a)  
(c)  
Continued on next page.  
13  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleanup - Latex materials (continued)  
6. Turn water supply on. Turn pump ON (l). Water will go  
5. Unclip the return tube from the suction tube and place it  
into the waste container. Turn the PRIME/SPRAY knob to  
PRIME.  
into the suction tube and out through the return tube. Let  
pump run for a few minutes to allow the return tube to be  
flushed.  
Leave pump running  
through steps 7 and 8.  
7. Place the original material container next to the waste  
container. Aim the spray gun into the side of the original  
material container and hold the trigger.  
8. While pulling the trigger, turn the PRIME/SPRAY knob to  
SPRAY to purge material from the hose back into the  
original container.  
SPRAY  
R P I M E  
Hold trigger  
Waste  
Original  
container  
material  
container  
Containers should  
be touching  
Keep holding trigger through next steps.  
9. When cleaning solution flows from the spray gun, keep  
holding the trigger and aim the spray gun into the side of  
the waste container.  
10. Trigger the gun until the fluid flowing out of the gun is  
clear. You may need to empty the waste container and  
continue flushing.  
Spray water into  
waste container  
11. Turn the PRIME/SPRAY knob to PRIME and trigger gun  
to relieve pressure.  
Spray material  
into original container  
Move on to Cleaning the Spray Gun Components  
14  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleanup - Oil-based materials  
2. Place a waste container next to the original material  
1. Lock the gun and remove spray tip assembly. Submerge  
suction set into a bucket with appropriate cleaning  
solution.  
container. Aim the spray gun into the side of the original  
material container and hold the trigger.  
Hold trigger  
Waste  
Original  
container  
material  
container  
Containers should  
Bucket with  
cleaning  
be touching  
solution  
• Hold trigger  
• Turn pump ON (l)  
• Turn PRIME/SPRAY knob to SPRAY  
3. While pulling the gun trigger, turn the pump ON (l), and turn  
the PRIME/ SPRAY knob to SPRAY to purge material from  
the hose back into the original container.  
Keep holding trigger through next steps.  
4. When cleaning solution flows from the spray gun, keep  
holding the trigger and aim the spray gun into the side of the  
waste container (ground gun with a metal container if  
flushing with flammable solvent).  
5. Trigger the gun until the fluid flowing out of the gun is  
clear. You may need to dispose and obtain new cleaning  
solution.  
Spray material into  
original container  
6. Turn the PRIME/SPRAY knob to PRIME and trigger gun  
to relieve pressure.  
Spray cleaning solution  
into waste container  
Move on to Cleaning the Suction Set.  
15  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleanup - Cleaning the Suction Set  
2. Remove the suction hose and return tube and clean it  
1. Lock the gun and turn the pump OFF (O).  
using the appropriate cleaning solution. You should also  
wipe the threads of the inlet nut (a) and remove and clean  
the inlet filter of the suction tube.  
GX-05  
GX-08  
GX-07  
(a)  
3. When suction set is clean, thread the suction tube back  
into the inlet valve, and replace the return tube onto the  
return tube fitting. Replace clip.  
4. Submerge the suction set into a bucket of NEW cleaning  
solution.  
5. Turn the PRIME/SPRAY knob to PRIME. Turn the pump  
ON (l), and trigger the gun once into a waste container to  
relieve pressure.  
6. Let the pump circlulate cleaning solution through the suction  
set for 2-3 minutes. Turn the pump OFF.  
2 to 3  
minutes  
IMPORTANT!  
If you used oil-based materials, you must flush the pump  
again using water to prepare it for storage. Repeat #1 - #11  
in Cleanup- Latex materials, instructions.  
Move on to Cleaning the Spray Gun Components.  
16  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleanup - Cleaning the Spray Gun Components  
1. Make sure the pump is switched OFF (O). Make sure the  
PRIME/SPRAY knob is turned to PRIME. Unplug the  
sprayer.  
2. Remove spray gun from the paint hose using adjustable  
wrenches.  
3. Remove filter from spray gun (refer to Cleaning the  
4. Remove spray tip (a) from spray guard assembly. Clean  
spray tip with a soft-bristled brush and the appropriate  
cleaning solution. Be sure to remove and clean the  
washer (b) and saddle seat (c) located in the rear of the  
spray tip assembly.  
Spray Gun Filter, page 12).  
GX-05  
GX-07  
GX-08  
(b)  
(c)  
(a)  
5. Install gun filter tapered-end first. Reassemble spray gun.  
6. Install spray tip (a), saddle seat (c) and washer (b), and  
replace spray guard assembly.  
GX-05  
GX-07  
GX-08  
(b)  
(c)  
(a)  
7. Thread the spray gun back onto the paint hose. Tighten  
with a wrench.  
17  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Short-Term Storage (up to 16 hours)  
Follow these steps when using latex materials only. If using materials that are oil-based, follow the Cleanup - Oil-based  
materials and Long-Term Storage steps.  
Shutdown  
1. Lock the spray gun off.  
GX-05  
GX-08  
GX-07  
2. Turn the PRIME/SPRAY knob to PRIME. Switch the pump  
3. Pour 1/2 cup water slowly on the top of the paint to  
prevent the paint from drying. Wrap the spray gun  
assembly in a damp cloth and place it in a plastic bag.  
Seal the bag shut. Place the sprayer in a safe place out  
of the sun for short-term storage.  
OFF (O). Unplug the sprayer.  
Startup  
2. Turn the PRIME/SPRAY knob to PRIME. Plug sprayer in.  
1. Remove the gun from the plastic bag. Stir the water into  
the paint.  
Turn the switch to ON (I).  
3. Turn the PRIME/SPRAY knob to SPRAY. Test the  
sprayer on a practice piece and resume spraying.  
18  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Long-Term Storage  
Follow these instructions only after all cleanup steps have been performed.  
1. Fill a cup or other container with separating oil  
(approximately 2 ounces) supplied with the unit and  
submerge the inlet valve into the oil. Light household oil  
can be substituted.  
2. Place a rag over the spray hose port, and turn the switch  
ON (l). When the oil has been sucked from the cup, turn  
the pump OFF (O).  
Separating oil  
3. Wipe the entire unit, hose and gun with a damp cloth to  
remove accumulated paint. Replace the high pressure  
hose to the paint hose port.  
If you have a cart model (9146, 9150, 9170, 9190), you can collapse the cart handle for easier storage.  
1. Twist the knobs on either side of the cart  
2. Slide the handle into the cart.  
counterclockwise.  
19  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning the Inlet Valve  
Cleaning or servicing the inlet valve may be required if the unit has priming problems. Priming problems may be  
prevented by properly cleaning the sprayer and following the long-term storage steps.  
1. Remove the suction set.  
2. Unscrew the inlet valve assembly (a) from the sprayer.  
Visually inspect the inside and outside of the inlet valve  
assembly. Clean any paint residue with the appropriate  
cleaning solution.  
(a)  
3. Lubricate the O-ring on the inlet valve (b). Replace inlet  
valve assembly by screwing it into the sprayer. Torque to  
23-27 ft lbs (9140, 9146, 9150) or 32-38 ft lbs (9170, 9190).  
4. Replace suction set and hand-tighten.  
(b)  
If priming problems persist, you may need to replace the  
inlet valve assembly. Call Customer Service to order a  
new inlet valve assembly.  
20  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fluid Section Seal Replacement Instructions  
Kit Part Number 0512228A (9140S, 9146, 9150)  
Kit Part Number 0516725 (9170, 9190)  
WARNING  
shutting the unit down for any purpose, including servicing or adjusting. After performing the Pressure Relief Procedure, be sure  
to unplug the unit before servicing or adjusting. Area must be free of solvents and paint fumes.  
(inlet) of the housing, and tighten with an adjustable  
wrench. This will drive the bottom seal into the correct  
Disassembly of the Fluid Section  
1. Remove the suction set.  
position.  
2. Remove the front cover and the four screws that secure it  
5. Align the piston with the yoke. Be careful not to damage  
using a T20 Torx head driver.  
the piston.  
3. Remove the yoke screw and washer that secures the dowel  
6. Apply a lithum grease to the holes in the yoke where the  
pin. The dowel pin connects the yoke to the piston.  
dowel is inserted.  
4. Using a pliers, pull the dowel pin out.  
7. Install the dowel pin to connect the yoke to the piston. The  
5a. For models 9140S, 9146, and 9150, rotate the pump shaft  
so the piston is in the top dead center position. This can be  
done by pushing on the yoke. This is required to  
disassemble all the parts.  
piston may have to be moved up or down to do this. The  
inlet valve may need to be removed again to move the  
piston.  
8. Install the yoke screw and washer to secure the dowel pin.  
5b. For models 9170 and 9190, inspect the yoke assembly  
and piston. In order to remove all the necessary parts, the  
piston must not be in the bottom dead center position. If  
the piston is at the bottom of the stroke, install the front  
cover and screws, turn the pump on briefly to index the  
piston, unplug the unit, and repeat step 2.  
9. Turn pump right side up and apply a few drops of  
Separating Oil or light household oil between the top nut  
and piston. This will prolong the seal life.  
10. Install front cover and four (4) screws.  
11. Replace inlet valve. Install the suction set.  
6. Unscrew and remove the inlet valve assembly (see page  
20).  
0512228A Kit  
(9140S, 9146  
7. Remove the piston assembly by pushing down on the  
piston near the yoke.  
8. Unscrew and remove the top nut using and adjustable  
wrench.  
9. Remove the worn seals using a flat head screwdriver or  
punch. Remove the top seal from the top and the bottom  
seal from the bottom by pressing against the side of the  
seal and popping it out. Be sure not to scratch the housing  
where the seals are located.  
Top nut  
and 9150)  
Top seal  
0516724 Kit  
(cup down)  
(9170, 9190)  
Yoke  
10. Clean the area where the new seals are to be installed.  
Screw  
Assembly of the Fluid Section  
Dowel Washer  
1. Lubricate the new top seal with Separating Oil (P/N 0516913)  
or light household oil and by hand place the seal (cup side of  
seal down) into the top port of the housing.  
2. Place a small amount of anit-seize on the threads of the top  
nut. Place the top nut into the top of the housing and  
tighten with an adjustable wrench. This will drive the top  
seal into the correct position.  
Piston/seal  
assembly  
0512228A Kit  
(9140S, 9146  
and 9150)  
0516724 Kit  
(9170, 9190)  
CAUTION! DO NOT  
attempt to remove the  
seals from the piston.  
Insertion  
tool  
3. Turn the pump upside down.  
Lubricate the seal on the  
piston/seal assembly similar to  
the top seal. Place the  
O-ring  
piston/seal assembly into the  
bottom of the housing. Insert  
the plastic insertion tool and  
thread into position to properly  
seat the piston/seal. Thread  
fully until tight. Remove the  
insertion tool.  
Inlet valve assembly  
0516292 (9140S,9146, 9150)  
0516296 (9170, 9190)  
4. Install the new O-ring on the inlet valve assembly, lubricate  
with Separating Oil (P/N 0516913), thread into the bottom  
21  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting / Maintenance  
Problem  
Cause  
Solution  
A. The sprayer does not start.  
1. The sprayer is not plugged in.  
2. The ON/OFF switch is set to OFF.  
3. The sprayer was turned off while still under  
pressure.  
1. Plug the sprayer in.  
2. Turn the ON/OFF switch to ON.  
3. Turn the pressure control knob to maximum  
pressure (+), or relieve pressure by turning the  
PRIME/SPRAY valve to PRIME.  
4. No voltage is coming from the wall plug.  
5. The extension cord is damaged or has too  
low a capacity.  
6. A fuse is blown in the sprayer.  
7. There is a problem with the motor.  
4. Properly test the power supply voltage.  
5. Replace the extension cord.  
6. Take sprayer to Authorized Service Center.  
7. Take sprayer to Authorized Service Center.  
B. The sprayer starts but does  
not draw in paint when the  
PRIME/SPRAY knob is set to  
PRIME.  
1. The paint bucket is empty or the suction  
tube is not totally immersed in the paint.  
2. The suction set is clogged.  
3. The suction tube is loose at the inlet valve.  
4. The inlet valve is stuck.  
1. Refill the bucket or immerse the suction tube in  
paint.  
2. Clean the suction set.  
3. Clean the tube connection and tighten it securely.  
4. Clean the inlet valve. Inlet may be stuck from old  
paint. Depress pusher stem to release.  
5. Outlet may be stuck from old paint. Remove inlet  
valve. Insert pen or pencil in housing to release.  
6. Replace the inlet valve.*  
5. The outlet valve is stuck.  
6. The inlet valve is worn or damaged.  
7. The PRIME/SPRAY valve is plugged.  
7. Take sprayer to Authorized Service Center.  
C. The sprayer draws up paint  
but the pressure drops when  
the gun is triggered.  
1. The spray tip is worn.  
2. The suction set screen is clogged.  
3. The gun filter is plugged.  
1. Replace the spray tip with a new tip.**  
2. Clean the suction set screen.  
3. Clean or replace the proper filter. Always keep  
extra filters on hand.  
4. The paint is too heavy or coarse.  
5. The inlet valve assembly is damaged or worn.  
6. The suction tube is loose.  
4. Thin or strain the paint.  
5. Replace the inlet valve.*  
6. Tighten the suction tube.  
D. The PRIME/SPRAY valve is  
on SPRAY and there is flow  
through the return tube.  
1. The PRIME/SPRAY valve is dirty or worn.  
1. Take sprayer to Authorized Service Center.  
E. The spray gun leaks.  
1. Internal parts of the gun are worn  
or dirty.  
1. Take the sprayer to a Authorized Service Center.  
F. The tip guard assembly  
leaks.  
1. The tip was assembled incorrectly.  
2. The washer is worn.  
1. Check the tip assembly and assemble properly (see  
page 17).  
2. Replace the washer* (see page 17).  
G. The spray gun will not spray.  
H. The paint pattern is tailing.  
1. The spray tip or the gun filter is plugged.  
2. The spray tip is not fully in the SPRAY  
position.  
1. Clean the spray tip or gun filter.  
2. Put the tip in the SPRAY position.  
1. The pressure is set too low.  
2. The gun or the suction filter is plugged.  
3. The suction tube is loose at the inlet valve.  
4. The tip is worn.  
1. Increase the pressure.  
2. Clean the filters.  
3. Tighten the suction tube fitting.  
4. Replace the spray tip.  
5. The paint is too thick.  
6. Pressure loss.  
5. Thin the paint.  
6. Refer to Causes and Solutions for problem C.  
* Special repair kits with instructions are available for these procedures. Refer to the Maintenance section of this manual for a list of  
the kits and their part numbers.  
** Additional parts are available for this procedure. Refer to the Accessories (page 71) section of this manual for a list of the parts  
and their part numbers.  
Daily Maintenance  
The only daily maintenance necessary is thorough cleaning and lubricating after usage. Follow the cleaning and lubricating procedures in  
this manual.  
Extended Maintenance  
Kit Part #  
Description  
Some pump parts eventually wear out from use and must be replaced. The  
following list indicates the available repair kits for the parts replaced by  
each kit. However, pump performance is the only reliable indicator of when  
to replace wear parts. Refer to the Troubleshooting section for more  
information on when to use these kits.  
0512228A Fluid Section Seal Kit (9140S, 9146, 9150)  
0516724  
0516292  
0516296  
Fluid Section Seal Kit (9170, 9190)  
Inlet valve kit (9140S, 9146, 9150)  
Inlet valve kit (9170, 9190)  
22  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List • Liste de pièces • Lista de piezas  
3
1
5
6
1
2
2
3
4
5
6
4
English  
English  
Model GX-05 spray gun  
Model GX-07 spray gun  
Item  
Part #  
Description  
Quantity  
Item  
Part #  
Description  
Quantity  
1
2
3
4
5
6
0501011  
0501415  
0516115  
0515220  
0515332  
0515329  
Guard Assembly ...................................1  
Tip, 415.................................................1  
Complete gun assembly.......................1  
Filter (yellow) ........................................1  
Seal.......................................................1  
Filter housing ........................................1  
1
0512127  
0515272  
0501011  
0501415  
0515220  
0515252  
0043590  
0278357  
Complete gun assembly (9146, 9150)...1  
Complete gun assembly (9170)............1  
Guard Assembly ...................................1  
Tip, 415..................................................1  
Filter, 9150 (yellow) ..............................1  
Filter, 9170 (white)................................1  
Spring ...................................................1  
Cap, filter housing.................................1  
2
3
4
5
6
Français  
Français  
Modèle du pistolet GX-05  
Modèle du pistolet GX-07  
Article N° de pièce  
Description  
Quantité  
Article N° de pièce  
Description  
Quantité  
1
2
3
4
5
6
0501011  
0501415  
0516115  
0515220  
0515332  
0515329  
Protège-embout et ses composants .1  
Embout, 415..............................................1  
Pistolet et ses composants ...............1  
Filtre, maille 100 (jaune) .....................1  
Joint d’étanchéité ..............................1  
Logement de filtre .............................1  
1
0512127  
0515272  
0501011  
0501415  
0515220  
0515252  
0043590  
0278357  
Pistolet et ses composants (9146, 9150) .1  
Pistolet et ses composants (9170)....1  
Protège-embout et ses composants .1  
Embout, 415..............................................1  
Filtre, 9150 (jaune) .............................1  
Filtre, 9170 (blanc)..............................1  
Ressort..............................................1  
Capuchon, logement de filtre............1  
2
3
4
5
6
Español  
Español  
Modelo de pistola GX-05  
Modelo de pistola GX-07  
Artículo Pieza#  
Descripción  
Cantidad  
Artículo Pieza#  
Descripción  
Cantidad  
1
2
3
4
5
6
0501011  
0501415  
0516115  
0515220  
0515332  
0515329  
Ensamble de protección ...................1  
Boquilla, 415 ......................................1  
Ensamble de la pistola......................1  
Filtro, malla 100 (amarillo) ................1  
Sello ..................................................1  
Alojamiento de filtro ..........................1  
1
0512127  
0515272  
0501011  
0501415  
0515220  
0515252  
0043590  
0278357  
Ensamble de la pistola (9146, 9150)...1  
Ensamble de la pistola (9170) ..........1  
Ensamble de protección ...................1  
Boquilla, 415......................................1  
Filtro, 9150 (amarillo)........................1  
Filtro, 9170 (blanco)..........................1  
Resorte..............................................1  
Tapa, alojamiento de filtro.................1  
2
3
4
5
6
67  
Español Français English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Parts List • Liste de pièces • Lista de piezas  
English  
8
7
6
5
4
3
Model GX-08 spray gun  
9
Item  
Part #  
Description  
Quantity  
10  
11  
1
0501517  
0501011  
0296261  
0296270  
0296230  
0296285  
0296284  
0296228  
9910201  
0296222  
0296286  
0296287  
0515252  
0296289  
0296342  
0043590  
9970114  
0296301  
Tip, 517......................................................1  
Guard assembly.........................................1  
Diffuser, 7/8" ..............................................1  
Valve spring unit ........................................1  
Trigger guard .............................................1  
Trigger assembly .......................................1  
Trigger screw (short)..................................1  
Gun housing ..............................................1  
Hex nut ......................................................1  
Retainer block............................................1  
Sliding pin ..................................................2  
Trigger screw (long)...................................1  
Filter, white.................................................1  
Washer.......................................................1  
Handle .......................................................1  
Spring ........................................................1  
Sealing ring................................................1  
Fitting .........................................................1  
2
3
12  
13  
4
5
6
7
8
2
1
14  
15  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
16  
17  
18  
Français  
Español  
Modèle du pistolet GX-08  
Modelo de pistola GX-08  
ArticleN° de pièce Description  
Quantité  
Articulo Pieza#  
Descripción  
Cantidad  
1
0501517  
0501011  
0296261  
0296270  
0296230  
0296285  
0296284  
0296228  
9910201  
0296222  
0296286  
0296287  
0515252  
0296289  
0296342  
0043590  
9970114  
0296301  
Embout, 517 ..............................................1  
Protège-embout.........................................1  
Diffuseur, 2,2 cm........................................1  
Ressort de soupape ..................................1  
Protège-doigts ...........................................1  
Détente et ses composants.......................1  
Vis de détente (courte) ..............................1  
Corps du pistolet........................................1  
Écrou hexagonal........................................1  
Bloc de retenue .........................................1  
Cheville coulissante...................................2  
Vis de détente (longtemps)........................1  
Filtre (blanc)...............................................1  
Rondelle.....................................................1  
Poignée......................................................1  
Ressort.......................................................1  
Bague d’étanchéité....................................1  
Raccord......................................................1  
1
0501517  
0501011  
0296261  
0296270  
0296230  
0296285  
0296284  
0296228  
9910201  
0296222  
0296286  
0296287  
0515252  
0296289  
0296342  
0043590  
9970114  
0296301  
Boquilla, 517..............................................1  
Ensamble de la protección .......................1  
Difusor 7/8” ................................................1  
Unidad del resorte de la válvula................1  
Protector del gatillo....................................1  
Ensemble del gatillo ..................................1  
Tornillo del gatillo (corto)............................1  
Alojamiento de la pistola............................1  
Tuerca hexagonal ......................................1  
Bloque de retención...................................1  
Pasador deslizante ....................................2  
Tornillo del gatillo (de largo).......................1  
Filtro (blanco).............................................1  
Arandela ....................................................1  
Mango........................................................1  
Resorte ......................................................1  
Aro sellador................................................1  
Ensemble del collarín ................................1  
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
68  
English Français Español  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List • Liste de pièces • Lista de piezas  
6
5
1
2
7
3
4
Español  
English  
Juego de succión  
Suction set  
Article Pieza# Descripción  
Cantidad  
Item  
Part #  
Description  
Quantity  
1
0516219 Ensamble del juego de succión (9140S) ......1  
0516218 Ensamble del juego de succión  
1
0516219  
0516218  
0512371  
0512389  
0512390  
0516284  
0327226  
9885553  
0515146  
Suction set (9140S)..............................1  
Suction set (all cart models).................1  
Return tube (9140S).............................1  
Return tube (all cart models)................1  
Clip........................................................1  
Filter......................................................1  
Squeeze clip .........................................1  
Return tube fitting .................................1  
Pump cleaning adapter.........................1  
(modelos de carrito) ......................................1  
2
2
0512371 Tubo de retorno (9140S)...............................1  
0512389 Tubo de retorno (modelos de carrito)............1  
0512390 Abrazadera....................................................1  
0516284 Filtro...............................................................1  
0327226 Abrazadera del apretón.................................1  
9885553 Conector del tubo de retorno ........................1  
0515146 Adaptador de limpieza de bomba .................1  
3
4
5
6
7
3
4
5
6
7
Français  
Dispositif d’aspiration  
Article N° de pièce Description  
Quantité  
1
0516219  
Dispositif d’aspiration et ses  
composants (9140S)..................................1  
Dispositif d’aspiration et ses  
0516218  
composants (modèles du chariot) .............1  
Tube de retour (9140S) .............................1  
Tube de retour (modèles du chariot) .........1  
Agrafe ........................................................1  
Filtre...........................................................1  
Agrafe de compression..............................1  
Raccord de tube de retour.........................1  
Adapteur de nettoyage de pompe.............1  
2
0512371  
0512389  
0512390  
0516284  
0327226  
9885553  
0515146  
3
4
5
6
7
69  
Español Français English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List • Liste de pièces • Lista de piezas  
3
4
5
1
7
6
8
9
11  
10  
2
English  
Description  
Français  
Article N° de pièce Description  
Item Part #  
Quantity  
Quantité  
1
2
3
0512336  
9885546  
0516516  
0516517  
9805228  
0516581  
0512355  
0516287  
0516288  
0516289  
0278369  
0278370  
0278373  
9890113  
9890104  
0516498  
0516505  
Stand assembly (9140S) . . . . . . . . . . . . . .1  
Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Hose bracket (9146, 9150, 9170) . . . . . . .1  
Hose bracket (9190) . . . . . . . . . . . . . . . . .1  
Pail bracket bolt . . . . . . . . . . . . . . . . . . . . .2  
Oiler cap . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
Pail bracket . . . . . . . . . . . . . . . . . . . . . . . .1  
Cart assembly (9146, 9150) . . . . . . . . . . .1  
Cart assembly (9170) . . . . . . . . . . . . . . . .1  
Cart assembly (9190) . . . . . . . . . . . . . . . .1  
Wheel (9146, 9150) . . . . . . . . . . . . . . . . . .2  
Wheel (9170) . . . . . . . . . . . . . . . . . . . . . . .2  
Wheel (9190) . . . . . . . . . . . . . . . . . . . . . . .2  
Wheel cap (9146, 9150, 9170) . . . . . . . . .2  
Wheel cap (9190) . . . . . . . . . . . . . . . . . . .2  
Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
1
2
3
0512336  
9885546  
0516516  
0516517  
9805228  
0516581  
0512355  
0516287  
0516288  
0516289  
0278369  
0278370  
0278373  
9890113  
9890104  
0516498  
0516505  
Ensamble de support (9140S) . . . . . . . .1  
Bouchon . . . . . . . . . . . . . . . . . . . . . . . . .4  
Support de flexible (9150, 9170) . . . . . .1  
Support de flexible (9190) . . . . . . . . . . .1  
Boulon de support de contenant . . . . . .2  
Bouchon de graisseur . . . . . . . . . . . . . . .1  
Support de contenant . . . . . . . . . . . . . . .1  
Chariot (9146, 9150) . . . . . . . . . . . . . . . .1  
Chariot (9170) . . . . . . . . . . . . . . . . . . . . .1  
Chariot (9190) . . . . . . . . . . . . . . . . . . . . .1  
Roue (9150) . . . . . . . . . . . . . . . . . . . . . .2  
Roue (9170) . . . . . . . . . . . . . . . . . . . . . .2  
Roue (9190) . . . . . . . . . . . . . . . . . . . . . .2  
Capuchon de roue (9146, 9150, 9170) .2  
Capuchon de roue (9190) . . . . . . . . . . . .2  
Capuchon . . . . . . . . . . . . . . . . . . . . . . . .1  
Capuchon . . . . . . . . . . . . . . . . . . . . . . . .1  
4
5
6
7
4
5
6
7
8
9
8
9
10  
11  
10  
11  
Español  
Articulo Pieza#  
Descripción  
Cantidad  
Articulo Pieza#  
Descripción  
Cantidad  
7
8
9
0516287  
0516288  
0516289  
0278369  
0278370  
0278373  
9890113  
9890104  
0516498  
0516505  
Carrito (9146, 9150) . . . . . . . . . . . . . . . .1  
Carrito (9170) . . . . . . . . . . . . . . . . . . . . .1  
Carrito (9190) . . . . . . . . . . . . . . . . . . . . .1  
Rueda (9146, 9150) . . . . . . . . . . . . . . . .2  
Rueda (9170) . . . . . . . . . . . . . . . . . . . . .2  
Rueda (9190) . . . . . . . . . . . . . . . . . . . . .2  
Tapa de rueda (9146, 9150, 9170) . . . . .2  
Tapa de rueda (9190) . . . . . . . . . . . . . . .2  
Tapa . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
Tapa . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
1
2
3
0512336  
9885546  
0516516  
0516517  
9805228  
0516581  
0512355  
Ensamblaje de banco (9140S) . . . . . . . .1  
Enchufe . . . . . . . . . . . . . . . . . . . . . . . . .4  
Soporte de manguera (9146, 9150, 9170) .1  
Soporte de manguera (9190) . . . . . . . . .1  
Perno del soporte del bote . . . . . . . . . . .2  
Tapa de lubricador . . . . . . . . . . . . . . . . .1  
Soporte pare el bote . . . . . . . . . . . . . . . .1  
4
5
6
10  
11  
70  
English Français Español  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories • Accessoires • Accesorios  
0279976  
0512134W  
0501411  
0501413  
0501415  
0501417  
0501419  
0501515  
0501517  
0501519  
0093930  
0156113  
Rallonge de manche, avec pivot, 1,8 m  
Pivot de 180°  
English  
Embout de pulvérisation, 411  
Embout de pulvérisation, 413  
Embout de pulvérisation, 415  
Embout de pulvérisation, 417  
Embout de pulvérisation, 419  
Embout de pulvérisation, 515  
Embout de pulvérisation, 517  
Embout de pulvérisation, 519  
Composé antigrippage  
Part #  
Description  
0516913  
0154830  
0270192  
0291000  
0279667  
0088154  
0508910  
0508914  
0515262  
0152308  
0155208  
0512181  
Separating Oil  
Hose, Whip End, 5’ x 3/16”  
Hose, Wireless, 25’ x 1/4"  
Hose, Wireless, 50’ x 1/4"  
Hose Connector, 1/4” x 1/4”  
Pressure Gauge  
Tip Extension, 12”  
Tip Extension, 24”  
Manche de rouleau télescopique TR-10, manchon  
de 22,9 cm, grain de 1,0 cm  
Power Roller Gun Attachment  
9" Roller Cover, 3/8” Nap  
9" Roller Cover, 3/4” Nap  
GX-08 Four Finger Metal  
Airless Spray Gun  
0154919  
0154675  
0154842  
0154918  
0279109L  
Filtre de pistolet vert (2)  
Filtre de pistolet jaune (2)  
Filtre de pistolet blanc (2)  
Filtre de pistolet rouge (2)  
Lubrifiant Pump Saver Plus  
0512180  
GX-07 Two Finger Metal Airless  
Spray Gun  
Español  
0516115  
0512182N  
GX-05 Airless Spray Gun  
GX-10 Two Finger Metal  
Airless Spray Gun w/Swivel  
Guard Assembly, G-Thread  
3 Foot Pole Extension w/Swivel  
6 Foot Pole Extensionw/Swivel  
180 Degree Swivel  
411 Trade Spray Tip  
413 Trade Spray Tip  
415 Trade Spray Tip  
417 Trade Spray Tip  
419 Trade Spray Tip  
515 Trade Spray Tip  
517 Trade Spray Tip  
519 Trade Spray Tip  
Anti-Seize Compound  
TR-10 Telescoping Roller, 9", 3/8" Nap  
Green Gun Filter (2)  
Yellow Gun Filter (2)  
White Gun Filter (2)  
Pieza#  
Descripción  
0516913  
0154830  
0270192  
0291000  
0279667  
0088154  
0508910  
0508914  
0515262  
0152308  
0155208  
0512181  
Lubricante de empaques  
Manguera 5’ x 3/16"  
Manguera 25’ x 1/4"  
Manguera 50’ x 1/4"  
Conector de manguera, 1/4" x 1/4"  
Manómetro  
Extensión de la boquilla, 12"  
Extensión de la boquilla, 24"  
Aditamento de la pistola del rodillo automático  
Funda del rodillo 9", pelillo de 3/8"  
Funda del rodillo 9", pelillo de 3/4"  
Pistola rociadora sin aire de metal  
del cuatro dedos GX-08  
0501011  
0279974  
0279976  
0512134W  
0501411  
0501413  
0501415  
0501417  
0501419  
0501515  
0501517  
0501519  
0093930  
0156113  
0154919  
0154675  
0154842  
0154918  
0279109L  
0512180  
Pistola rociadora sin aire de metal  
del dos dedos GX-07  
0516115  
0512182N  
Pistola rociadora sin aire GX-06  
Pistola rociadora c/oscilador sin  
aire de metal del dos dedos GX-10  
Ensamblaje de protección, Roscado G  
Tubo de extensión de 92 cm c/oscilador  
Tubo de extensión de 1.8 m c/oscilador  
Oscilador de 180 grados  
Boquilla rociadora 411  
Boquilla rociadora 413  
Boquilla rociadora 415  
Boquilla rociadora 417  
Boquilla rociadora 419  
Boquilla rociadora 515  
Boquilla rociadora 517  
Boquilla rociadora 519  
Compuesto antiatascos  
Rodillo telescópico TR-10, pelillo de 9", 3/8"  
Filtro de pistola verde (2)  
Filtro de pistola amarillo (2)  
Filtro de pistola blanco (2)  
Filtro de pistola rojo (2)  
0501011  
0279974  
0279976  
0512134W  
0501411  
0501413  
0501415  
0501417  
0501419  
0501515  
0501517  
0501519  
0093930  
0156113  
0154919  
0154675  
0154842  
0154918  
0279109L  
Red Gun Filter (2)  
Pump Saver Plus Protector  
Français  
N° de pièce  
0516913  
0154830  
0270192  
0291000  
0279667  
0088154  
0508910  
0508914  
0515262  
0152308  
0155208  
0512181  
0512180  
0516115  
0512182N  
Description  
Huile séparatrice  
Flexible, 1,5 m x 0,5 cm  
Flexible, 7,6 m x 0,6 cm  
Flexible, 15,2 m x 0,6 cm  
Raccord de flexible, 0,6 cm2  
Manomètre  
Rallonge d’embout, 30,5 cm  
Rallonge d’embout, 61,0 cm  
Rouleau électrique, accessoire pour pistolets  
Manchon de rouleau de 22,9 cm, grain de 1,0 cm  
Manchon de rouleau de 22,9 cm, grain de 1,9 cm  
Pistolet sans air à détente allongée - métal (GX-08)  
Pistolet sans air à détente courte- métal (GX-07)  
Pistolet sans air (GX-05)  
Protector Pump Saver Plus (lubricante)  
Pistolet sans air à détente courte, avec pivot - métal  
(GX-10)  
0501011  
0279974  
Protège-doigts, filets « G »  
Rallonge de manche, avec pivot, 0,9 m  
71  
Español Français English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty • Garantié • Garantia  
LIMITED WARRANTY  
AIRLESS PAINT SPRAY EQUIPMENT  
This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted to the original retail purchaser against defects in material and workmanship for  
one year from date of purchase.  
This warranty does not cover damage resulting from improper use, accidents, user's negligence or normal wear. This warranty does not cover any defects or damages  
caused by service or repair performed by anyone other than a Wagner Authorized Service Center. This warranty does not apply to accessories.  
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO ONE YEAR FROM DATE OF PURCHASE.  
WAGNER SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FROM BREACH OF THIS  
WARRANTY OR ANY OTHER REASON.  
If any product is defective in material and/or workmanship during the applicable warranty period, return it with proof of purchase, transportation prepaid to any Wagner  
Authorized Service Center. (Service Center listing is enclosed with this product.) Wagner’s Authorized Service Center will either repair or replace the product (at Wagner’s  
option) and return it to you, postage prepaid.  
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.  
GARANTIE LIMITÉE  
MATÉRIEL DE PULVÉRISATION DE PEINTURE SANS AIR  
Ce produit, fabriqué par Wagner Spray Tech Corporation (Wagner), est garanti, au bénéfice de l’acheteur au détail d’origine, contre tout vice de matières et toute malfaçon  
pour un an à compter de la date d’achat.  
La présente garantie ne s'applique pas aux dégâts entraînés par une utilisation incorrecte, par la négligence de l'usager ou par l'usure normale. La présente garantie ne  
s'applique pas non plus aux défectuosités ou dommages résultant de l'entretien ou de la réparation que fait une personne quelconque qui ne soit pas membre d'un centre  
d'entretien autorisé pour les produits Wagner. La présente garantie ne s'applique pas aux accessoires.  
TOUTE GARANTIE IMPLICITE DE QUALITÉ MARCHANDE OU D'ADAPTATION À UN USAGE PARTICULIER EST LIMITÉE À UNE PÉRIODE DE 30 JOURS POUR  
UNE UTILISATION PROFESSIONNELLE OU DE LOCATION ET D'UNE ANNÉE POUR L'UTILISATION DOMESTIQUE, À COMPTER DE LA DATE D'ACHAT.  
TOUTE GARANTIE IMPLICITE DE VENDABILITÉ OU DE CONVENANCE À UNE DESTINATION PARTICULIÈRE EST LIMITÉE À UN AN À COMPTER DE LA DATE  
D’ACHAT.  
Si un produit est défectueux en ce qui concerne les matériaux ou l'exécution pendant la période de garantie applicable, vous devez le retourner, avec une preuve  
d'achat et frais de port payés, à n'importe quel centre d'entretien autorisé pour les produits Wagner. (Une liste de ces centres d'entretien est jointe à ce produit.) Le  
centre d'entretien autorisé pour les produits Wagner réparera ou remplacera le produit (à la discrétion de Wagner) et vous le retournera par la poste, avec frais de port  
payés.  
CERTAINES PROVINCES INTERDISENT LES RESTRICTIONS SUR LA DURÉE D'UNE GARANTIE IMPLICITE OU L'EXCLUSION DES DOMMAGES  
ACCESSOIRES OU INDIRECTS. IL SE PEUT DONC QUE LA RESTRICTION ET L'EXCLUSION ÉNONCÉES CI-DESSUS NE S'APPLIQUENT PAS À VOUS.  
LE PRÉSENTE GARANTIE VOUS ACCORDE DES DROITS JURIDIQUES SPÉCIFIQUES, ET VOUS AVEZ PEUT-ÊTRE D'AUTRES DROITS, QUI PEUVENT  
VARIER D'UNE PROVINCE À L'AUTRE.  
GARANTÍA LIMITADA  
EQUIPO DE ATOMIZACIÓN DE PINTURA SIN AIRE  
Este producto, fabricado por Wagner Spray Tech Corporation (Wagner), está garantizado ante el comprador original contra defectos de materiales y mano de obra  
durante un año contado a partir de la fecha de compra.  
Esta garantía no cubre los daños que sean resultado de un uso inapropiado, accidentes, negligencia del usuario o un desgaste normal. Esta garantía no cubre ningún  
defecto o daño que haya sido causado por los servicios o reparaciones llevadas a cabo por alguien que no sea un técnico del Centro de Servicio Autorizado de  
Wagner. Esta garantía no es válida para ningún accesorio.  
CUALQUIER GARANTIA IMPLICITA DE COMERCIALIZACION O IDONEIDAD PARA CUALQUIER PROPOSITO EN PARTICULAR QUEDA LIMITADA A UN AÑO A  
PARTIR DE LA FECHA DE COMPRA.  
WAGNER NO SERÁ EN NINGÚN CASO RESPONSABLE DE NINGÚN DAÑO INCIDENTAL O DE CONSECUENCIA DE NINGUNA CLASE, QUE RESULTE DE  
VIOLAR ESTA GARANTÍA O POR CUALQUIER OTRA RAZÓN.  
Si algún producto llegara a tener defectos de material y/o mano de obra durante el período de validez de la garantía, devuélvalo junto con el comprobante de compra  
y flete previamente pagado, a cualquier Centro de Servicio Autorizado de Wagner. (La lista de Centros de Servicio viene adjunta con este producto.) El Centro de  
Servicio Autorizado de Wagner reparará o reemplazará el producto (según la opción de Wagner) y se lo devolverá, con porte previamente pagado.  
ALGUNOS ESTADOS NO PERMITEN LIMITACIONES EN CUANTO A LA DURACIÓN DE UNA GARANTÍA IMPLÍCITA O LA EXCLUSIÓN DE DAÑOS  
INCIDENTALES O DE CONSECUENCIA, DE MANERA QUE LA LIMITACIÓN Y EXCLUSIÓN ANTERIORES PODRÍAN NO SER VÁLIDAS PARA USTED.  
ESTA GARANTÍA LE CONCEDE DERECHOS LEGALES ESPECÍFICOS, PERO USTED PODRÍA TENER DERECHO A OTROS, LOS CUALES VARÍAN DE UN  
ESTADO A OTRO.  
Copyright © 2005 Wagner Spray Tech - All rights  
reserved, including right of reproduction in whole or  
Wagner Spray Tech  
1770 Fernbrook Lane  
in part, in any form.  
Plymouth, MN 55447  
1-800-880-0993  
U.S. Patent Nos. 6,435,846 7,071,429  
6,599,107 Other patents pending  
72  
English Français Español  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technika Flat Panel Television 19 208 User Manual
Tesla Power Supply TI2000GPU 24 User Manual
Tokina Camera Accessories TC0812DC User Manual
Tribest Food Saver SD P9000GP User Manual
Ultimate Support Systems Musical Toy Instrument GS 1000 User Manual
Verilux Indoor Furnishings CWST1 User Manual
ViewSonic Car Video System VS15615 User Manual
Vizio Model Vehicle M470VSE User Manual
Wadia Digital Personal Computer DECODING COMPUTER User Manual
Weed Eater Blower 545137215 User Manual