Introduction and Overview
The Wacom® DTU-710™ Interactive Pen Display combines an LCD monitor with a
Wacom tablet.
This gives you a direct point-and-draw-on-screen interface that can be used with a
Personal Computer (PC) or Macintosh computer. DTU-710's basic components include
a Wacom tablet internally mounted behind a 17.0" diagonal TFT color LCD monitor, and
Wacom's pen.
Your DTU-710 Interactive Pen Display offers a number of significant advantages over a
standard monitor:
■
Reduced power consumption
■
Reduced heat generation
■
Requires less work space
■
Flicker free and easier on the eyes
■
Integrated input and display
■
Pressure-sensitive drawing directly on the display screen.
This manual describes how to install DTU-710 hardware and software. It also describes
how to use DTU-710 and the pen. Note that the computer treats the two parts of
DTU-710 (the LCD monitor and the Wacom tablet) as separate pieces of hardware.
Therefore, the installation process is completed in two stages. First, you will install the
LCD monitor portion of DTU-710. In the second stage you will install DTU-710's tablet
functionality.
You can find information on using the Wacom Tablet Control Panel for customizing your
tablet and pen settings in the online Help, located under the Help menu in the Wacom
Tablet Control Panel.
The following are not included with this product:
■
Information about your specific computer hardware
■
Information about your operating system
■
Information about application software.
Please refer also to your computer hardware, operating system, or software application
manuals.
To use the pressure-sensitivity of the pen with your favorite drawing application, refer to
instructions in that application's manuals.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Do not put heavy articles on DTU-710; this may damage the display screen
■
or stand.
Do not place heavy article on DTU-710 cabling, repeatedly bend the
■
cables, or apply heavy stress on the cable connectors; this may damage the
unit or your cabling.
This product is for use with a VGA or DVI graphics card; using an
■
inappropriate graphics card may damage DTU-710.
Do not connect or disconnect the DVI video cable or power cable while
■
DTU-710 and your computer is turned on; it may damage the LCD display or
computer video card.
Do not disassemble DTU-710 or pen. This may cause DTU-710 or pen to
■
malfunction. In this case, Wacom shall have no responsibility to repair or replace
the product.
Do not use or store DTU-710 where:
■
- Temperature changes are severe (e.g., outdoors or inside a vehicle).
- DTU-710 and pen are exposed to direct sunlight or heat from a heating appliance.
- DTU-710 and pen are exposed to water or any other kind of liquid.
- Temperature or humidity exceeds the specifications.
Do not block the ventilation holes in the rear panel; this may overheat and
■
damage DTU-710.
Do not use DTU-710 in a dusty environment; It may damage the unit.
■
■
Do not scratch the cover glass of DTU-710. Avoid placing sharp objects on
the glass surface.
Do not use detergent to clean the cover glass of DTU-710; this may alter the
■
surface friction and deteriorate the handwriting feel.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Packed Components
In your package you will find the following items:
AC Adaptor and Cable
DTU-710 main unit
Pen with Pen Stand
USB Cable and RS-232C Cable*
User's Guide
Wacom Tablet CD
Contains the driver soft-
ware.
(Windows/Macintosh)
DVI-DVI Cable and DVI-VGA Cable*
Some package configurations includ an additional CD containing bundled software applications.
Please retain the package box for use when storing or shipping DTU-710.
*
For DTU-710 only. Do not use with other devices.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect DTU-710 to a computer
Connect DTU-710 to a computer as adisplay.
CAUTION
Do not use any cable that did not come with DTU-710; use of an improper cable
may damage DTU-710.
■
Make sure your graphics card has a VGA or DVI connector, and that you correctly
set the DTU-710 Analog (VGA)/Digital (DVI) switch for the graphics card you are
using. The use of an improper video card may damage DTU-710.
Do not connect or disconnect the video or power cable while DTU-710 or your
computer are turned on; this can damage the LCD display or computer video card.
Never connect or disconnect the DVI video cable or power cable while your computer
or DTU-710 is powered on. This can damage the LCD display or video card.
■
■
■
Turn off your computer. The cover in the rear of DTU-710 is made to slide in the
1.
2.
3.
direction of " ", and is removed.
▶
Connect the DVI-to-DVI cable or DVI-to-VGA cable between DTU-710 and your
computer.
Set the DVI/VGA switch. Move it up for analog (VGA) mode, and move it down for
digital (DVI) mode.
Connect the AC adaptor to DTU-710.
4.
5.
Connect the AC adaptor power cable and plug the adaptor into an AC outlet.
Be sure to connect an earth cable.
Turn on the power switch of DTU-710. The power lamp will light blue, and then
turns orange.
6.
Turn on your computer to start your operating system.
7.
8.
The maximum resolution of DTU-710 is 1280 x 1024, True Color . As necessary,
configure the monitor control panel settings for the proper size and color resolution.
The number of colors is constrained by the performance of your computer or
graphics card. Refer to the documentation of the manufacturer for details.
If you are using analog (VGA) mode, you may also want to fine-tune the display.
Please refer to Adjusting the LCD Monitor on page 22 for more information.
To install the Wacom tablet software, turn off your computer and connect the USB
cable or serial data cable.
9.
Fix cables to a cable guides. Shut the connector cover is and take out the cables
10.
from the hole of the cover.
Install tablet software. Refer to
on page 8
Tablet Software Installation for Windows and
11.
Macintosh
.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel of your computer
To serial port
Video card
Connect one cable only.
To USB port
2
DVI-DVI or DVI-VGA cable
Ground
to AC outlet
RS-232C connector
USB connector
Cable guides
DC input
DVI/VGA switch
DVI-I connector
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Tablet Driver Installation
Before you install the tablet software of DTU-710, you need to connect the USB cable
or the serial data cable (Windows only) of DTU-710 to your computer. After connecting
it, you turn on DTU-710 and your computer.
Windows:
First turn on the DTU-710. Then turn your computer on and login, allowing
1.
the operating system to fully load. The DTU-710 will automatically register as
a USB device.
Windows 98SE: The ADD NEW HARDWARE WIZARD will display.
Follow the prompts, selecting the default options. If prompted to install
drivers for the USB Human Interface Device, insert the Windows
98SE CD, click OK, and enter the location of the Windows CAB
files (e.g., D:\WIN98). Note that the files may be located on your hard disk in
the C:\WINDOWS\OPTIONS\CABS folder.
Insert the DTU-710 tablet driver CD into the CD-ROM drive. The
2.
DTU-710 menu should automatically display. If the menu does not
display, double-click on the INSTALL icon (located on the CD).
Click on the INSTALL PEN TABLET button and follow the prompts
to install the driver software.
Macintosh:
First turn on the DTU-710. Then turn on your computer and allow the
1.
operating system to fully load. The DTU-710 will automatically register
as a USB device. Disable any virus protection programs and close all open
applications before installing the software.
Insert the DTU-710 tablet driver CD into your computerʼs CD-ROM drive.
2.
Double-click on the INSTALL icon located on the CD. Click on the INSTALL
PEN TABLET button and follow the prompts to install the driver software.
After the software installation has been completed, make sure you can use
3.
your pen on the DTU-710 display to move the screen cursor.
Be sure to check the Read Me file for late-breaking news. If you have trouble
installing the DTU-710, see the Troubleshooting section beginning on page 27 of
this manual.
Next Steps:
Be sure to adjust the tablet calibration to precisely align the screen cursor position with
the location of the pen tip. Refer to
on page 14. To learn more
Calibrating the DTU-710
about Using the DTU-710, proceed to
and to
Customizing The DTU-710 - The Basics
Using The Pen.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Uninstalling The DTU-710
Follow the appropriate procedure below to remove the DTU-710 Interactive Pen Display
and software from your system.
When you remove the Wacom tablet driver software from your
Important
system, any other Wacom tablet connected to your computer
will no longer operate with full Wacom tablet functionality.
Windows XP:
Click START. In the start menu, select CONTROL PANEL. Then select ADD
1.
OR REMOVE PROGRAMS.
In the ADD OR REMOVE PROGRAMS window, choose the pen display tablet
2.
option and click on the CHANGE/REMOVE button. Follow the prompts to
remove the software driver.
When the pen tablet driver has been removed, shut down your system, power
3.
off your computer, and turn off the DTU-710. When your computer and the
DTU-710 are off, disconnect the DTU-710 from your computer.
Windows 98SE, Me, or 2000:
Click the Windows START button. Then choose SETTINGS and CONTROL
1.
PANEL.
In the CONTROL PANEL window, double-click on the ADD/REMOVE
2.
PROGRAMS icon. In the dialog box that appears, choose the pen display tablet
option.
Click on the ADD/REMOVE... button and follow the prompts to remove the
3.
software driver.
When the pen tablet driver has been removed, shut down your system, power
4.
off your computer, and turn off the DTU-710. When your computer and the
DTU-710 are off, disconnect the DTU-710 from your computer.
Macintosh OS X, v10.2.6 or greater:
From the FINDER, choose APPLICATIONS from the GO menu and open the
1.
tablet folder.
Double-click on the REMOVE TABLET icon and select the REMOVE
2.
TABLET SOFTWARE button.
After the removal is completed, click OK.
3.
Shut down your computer and turn off the DTU-710. When your computer and
4.
the DTU-710 are off, disconnect the DTU-710 from your computer.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing The DTU-710 – The Basics
The Wacom Tablet Control Panel makes it easy to customize your Interactive Pen
Display and the pen.
Opening the Wacom Tablet Control Panel
To open the control panel, use the DTU-710 pen on the pen display tablet:
Click on the Windows START button and choose ALL
Windows:
PROGRAMS. (For versions other than Windows XP, choose the
PROGRAMS group.)Then select WACOM TABLET and choose the WACOM
TABLET option.
Open SYSTEM PREFERENCES from either the Dock, the Apple
Macintosh:
menu, or from the APPLICATIONS folder. Then double-click on the WACOM
TABLET icon.
If more than one pen display tablet is installed on your system, the
Note
control panel will change the settings for the tablet that was last
used before opening the control panel.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel Basics
Open the Tablet control panel to begin customizing your product. Experiment with
different settings to find what works best for you. Any changes you make will take effect
immediately, but you can always click DEFAULT to return to the factory settings.
Additionally, your keyboard tab and arrow keys can be used to navigate the control
panel.
Customizing The Pen
Enables the eraser function
for a pen with an eraser.
Uncheck this box if your pen
does not have an eraser.
Selects the side switch button functions for pens
equipped with a side switch. See page 12.
Closes the
control panel.
Customizes the amount of
pressure needed to erase
with the eraser.See page
13.
Customizes the amount of
pressure needed to click
or draw with the pen.See
page 12.
Adjusts the size
of the double-
click area.
See page 20.
When checked, an
audible “click” sound will
be heard whenever a pen
click occurs and your
computer speakers are
turned on.
Returns the
PEN tab settings
to their factory
defaults.
Displays information
about the control
panel and driver.
Software driver version.
If more than one pen display tablet is installed on your system, the control panel
will change the settings for the tablet that was last used before opening the control
panel.
Depending on the pen that came with your product configuration, there
Note
may be more options displayed on the control panel than are actually
present on the pen. When customizing your pen, choose those options
that match the buttons on the pen you are working with.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing DTU-710 – The Basics
Control Panel Details
Pen Tip Feel & Eraser Feel
Move the Tip or Eraser Feel slider to adjust the sensitivity of the pen tip or eraser.
To create broad brush strokes or to click with a light touch, use a soft tip setting.
maximum control while drawing thin lines, use a firmer setting.
For
Side switch
The pen side switches and Cordless Mouse buttons each have a pull-down menu
that allow you to choose the function that will be performed when the button is
pressed. The following list describes the available functions. Some options,
however, are not available for all buttons.
(Windows),
(Macintosh)
Left-Click
Click
•
this option simulates a left mouse button click.
(Windows & Macintosh)
Right-Click
•
•
•
this simulates a right mouse button click.
(Windows & Macintosh)
Middle-Click
simulates a middle mouse button click.
(Windows),
(Macintosh)
Double-Click
Left Double-Click
simulates a left mouse button double-click. For easier double-clicking, use this
function instead of tapping twice with your pen.
(Windows),
(Macintosh)
Click-Lock
Left Click-Lock
•
simulates holding down the left mouse button. Press the tool button once to
initiate click lock. Press the button again to release click lock. Click lock is
useful for dragging objects or selecting blocks of text.
Keystroke
•
enables you to simulate a series of keystrokes. Selecting this option displays
the define keystroke dialog box, where you can enter a keystroke or keystroke
sequence to play back. Keystroke combinations can include letters, numbers,
function keys (such as F3) and modifier keys (such as SHIFT, ALT, or CTRL
for Windows, or SHIFT, OPTION, COMMAND, and CTONTROLl for Macintosh).
Pressure Hold
•
sets the button so that, when pressed, the pressure is locked at the current
pressure level until the button is released. For example, you can paint with
pressuresensitivity until you reach the bush size that you like.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode Toggle
•
•
toggles between Pen Mode and Mouse Mode.
(pen and Macintosh OS X )
Ink Toggle
lets you use your pen to toggle the Ink Anywhere function of Inkwell on and off.
Note that Ink must be turned on for this button function to work.
Erase
•
works like the eraser on a pencil in graphic applications that support the Erase
function.
MODIFIER
•
Enables you to assign modifier key(s) (such as SHIFT or CTRL). Many
applications use modifier keys to constrain the size or placement of objects.
Selecting this option displays the DEFINE MODIFIER dialog box where you
can assign one or more modifier key functions.
Select the CLICK box plus one or
more modifier key options if you
want a mouse click to happen
whenever you press the tool
button.
The available
Macintosh:
options will be SHIFT, CONTROL,
OPTION, COMMAND, and CLICK.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing DTU-710 – The Basics
Calibrating the DTU-710
You will need to calibrate the pen display tablet in order to align the screen cursor
position with the position of the pen on the display screen. This is required to
adjust for parallax caused by the display screen cover glass. Set the DTU-710 in
its working position, then follow the procedure below.
From the WACOM TABLET Control Panel, select the CALIBRATION tab.
1.
If you are working with multiple monitors, select the Monitor that corresponds to the
tablet's LCD display. (Only monitors that are set to one of the resolutions supported
by the DTU-710 will appear in the list.)
Click on the CALIBTRATE... button to display the monitor calibration screen.
2.
Cross-hairs
Adjustment pattern
for phase and pitch.
See
Adjusting Pitch
and Phase (VGA
on page 26 for
Only)
details.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Hold the pen as you normally do, and use the pen tip to click on the cross-hairs in the
upper-left corner.
3.
Then click on the cross-hairs that are displayed in the lower-right corner. (For
Windows systems, you will need to click APPLY or OK for the changes to take effect.)
4.
5.
Test the alignment and click OK to accept the calibration. Click TRY AGAIN to
recalibrate.
Be sure to read the directions in the calibration screen for detailed instructions and
additional options. The calibration setting applies to all applications.
If more than one pen display tablet is installed on your system, the
Note
control panel will change the settings for the tablet that was last used
before opening the control panel.
To calibrate two pen display tablets, first touch the pen to tablet #1 and open the control
panel without touching the pen to tablet #2. In the control panel, select the correct
monitor and calibrate tablet #1. Close the control panel, touch the pen to tablet #2, and
again open the control panel without touching the pen to tablet #1. Select the correct
monitor and calibrate tablet #2.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DTU-710 Component Functions
Front View
- (minus) Button, + (plus) Button
MENU Button
Opens and closes the
OSD*1 menu.
In the OSD*1 menu, Use these buttons to select an option that can then be
activated. After activating a selected option, press the + button to increase a
selected item value, and press the - button to decrease it.
ENTER Button
Press this button when you select or exit an
MENU
-
NE
ENTER
STATUS POWER
item in the OSD*1 menu.
P 22
☞
POWER Switch
Turns the power to the unit on or off.
POWER Lamp
Lights blue when power has been supplied
to both the DTU-710 and the computer and
a video signal is present.
Glows orange when no video signal is
received by the DTU-710. (e.g., Your
computer is turned off, starting up, or has
entered a power management mode in
which video signals are not sent.)
STATUS Lamp
Lights blue when the pen is in the active
area of the pen display tablet and the pen
tip, side switch, or eraser are pressed. Note
that the USB cable must be plugged into an
active USB port before the LED will light.
Integrated Tablet and LCD Screen
The LCD monitor*2 and tablet sensor function*3 as an
integrated input and output device.
The LCD resolution is 1280 x 1024 pixels at 16,194,277
colors. The tablet sensor reports coordinates, pressure,
switch, and eraser information.
On Screen Display. P. 22
As properties of LCD panel display, you may notice the followings. They do not mean the LCD is
defective.
☞
*1
*2
- When exerting hard downward pressure on the display, a moir pattern may temporarily appear.
- A very small number of pixels may appear in incorrect color.
- If an image area has fine striping (such as screen stripes), it may flicker or display a moir pattern or
pooling image.
- When a still image is displayed for a long period of time, an afterimage may remain for a short period
of time.
As the tablet portion of DTU-710 emits electromagnetic waves at a certain frequency, if another tablet
*3
is closely placed to DTU-710, the screen cursor may jitters or jumps around. To solve this problem,
place the tablet away from DTU-710.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear View
Stand Adjustment Lever
Pull this lever to adjust the
stand. Release the lever to
lock the stand in place.
Connector Panel Cover
To remove, slide it to the right.
CAUTION
Be careful to avoid
catching your finger in
the gap of the movable
portion of the stand.
Stand
The stand can be used to
adjust the tilt angle of the unit
from low (16°from horizontal)
to high (72° from horizontal).
Be sure to adjust the tilt angle of the stand to the low tilt position
before packaging DTU-710. If you do not close the stand, the
notched mechanism may be damaged during transportation and
storage. Do not lift the unit by the stand; this may damage the
stand mechanism. When lifting or moving the unit, always do so
by grasping the main body casing.
Important
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DTU-710 Component Functions
Using an Alternate Mount or Stand
If you will be using DTU-710 in an installation that requires the use of an alternate
mounting platform, you can remove the adjustable stand from DTU-710 and mount the
pen display onto a VESA conforming mount arm or stand.
A VESA mounting platform will require mount screws that are 4 mm wide with a 0.7
mm pitch (M4 Regular), and a maximum screw clearance depth of 15 mm. Exceeding
the screw clearance depth of 15 mm will damage DTU-710 internal components.
To remove the adjustable stand and attach DTU-710 to a different mounting platform:
Turn off your computer and
1.
power off DTU-710. Then
disconnect all cables from
DTU-710.
Protect the display screen
2.
surface by spreading a soft
cloth onto a flat table and
placing DTU-710 face down
on the cloth.
Remove the four screws
and lift the adjustable stand
3.
assembly away from the body
of DTU-710.
unscrew
Using the appropriate screws
for your mounting platform,
firmly attach DTU-710 to the
alternate mounting platform.
4.
5.
Rettach the cabling.
CAUTION
When attaching DTU-710 onto
an alternate mounting platform,
be sure to follow all instructions
in the documentation supplied
by the platform manufacturer.
If improperly installed, the unit
could fall and be damaged.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Pen
Pen
Hold the pen as you would a pencil. Make sure the side switch is in a convenient location
where you can press it with your thumb or forefinger, but won't accidentally press it
while drawing.
Eraser
Eeasar
Second Side Switch
Side Switch
Tip Switch
Pen Tip
When the pen tip is within proximity (5 mm or 0.2 in) of the active area, the tablet
reports:
- The x, y coordinates of the pen tip.
- The pressure applied to the pen tip.
- Whether a side switch is on or off.
When pressure is applied to the pen tip, the tip switch is turned on and the pen
simulates a mouse button click.
Eraser
To use the eraser, hold the pen upside down. When the eraser is within proximity
of the active area, the tablet reports the x, y coordinates and the pressure applied to
the eraser.
The eraser can be used as an eraser or assigned to another function, depending on
the application. The tablet distinguishes the tip switch from the eraser switch.
Side Switch and Second Side Switch
These switches are programmable, and can be used to perform the same click and
double-click functions as the tip switch. The switches are turned on when pressed,
and are otherwise turned off. Please refer to the online Help for more information
on side switch settings.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Pen
Using a Pen
Pointing and Selecting
Move the pen above DTU-710 screen to position the screen cursor. The cursor instantly
jumps to the new location (absolute positioning). Press the pen tip on DTU-710 screen to
make a selection.
If the screen cursor is not aligned with the pen tip, you will need
Note
to calibrate DTU-710.
Clicking
Tap DTU-710 screen once with the pen tip, or touch the pen to the display screen with
enough pressure to generate a mouse click.
Double-Clicking
Press the upper side switch (Windows systems) or quickly tap DTU-710 screen
twice in the same place with the pen tip. Double-clicking is easier when the pen
is perpendicular to the tablet screen.
Dragging
Select an object, then slide the pen tip across DTU-710 screen to move the object.
Erasing
In supporting applications, the pen's eraser works like the eraser on a pencil. In
text applications, use the eraser to select text, then lift the eraser from the tablet to
delete the text.
Removing the Side Switch
If you prefer to remove the side switch:
Firmly clasp the switch in the middle and pull out. (Press in on the rubberized grip in
order to better grasp the switch.)
1.
Rubber Grip
Sectional
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Important
Do not remove the switch by prying it from either end as
this may damage your Pen.
Remove the pen tip cone by turning it counterclockwise.
2.
Pull the grip forward over the pen tip. NEVER adjust the trimmer capacitor that became
visible as it is fine tuned. When using the pen without the side switch, always istall the
3.
optional grip in order to protect the trimmer capacitor.
Install the optional grip by aligning the pen case rails with the grooves inside the grip
and pushing the grip over the pen tip.
4.
Replace the pen tip cone by turning it clockwise onto the pen.
5.
reverse the above procedure.
To reinstall the side switch,
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the LCD Monitor
Factory Presets, Multi-sync, and User Settings
To display images with the best quality (based on the incoming
Factory Presets:
signal), DTU-710 comes with a number of factory default standard display modes.
When connected as a VGA display, DTU-710 attempts to automatically
Multi-Sync:
synchronize to the incoming signal. Multi-Sync functions if the horizontal frequency is
between 30 to 80 kHz and the vertical frequency is between 50 to 75 Hz. If DTU-710
does not automatically synchronize with the incoming signal, you can use the OSD
Reset Auto Adjust option to initiate display synchronization. If necessary, further
screen display adjustments can be manually made using the On Screen Display (OSD)
controls.
When you manually set the display using the On Screen Display (OSD)
User Settings:
function, the settings are stored within DTU-710 for use the next time the unit receives
a similar signal. This is applicable to all display modes.
Working with OSD (On Screen Display) Menu
press the MENU ( ) button.
To open the main MENU,
Use the + ( ) or - ( ) buttons to select an option. When the option you want to adjust
is highlighted, press the ENTER ( ) button. The current settings and adjustment sub-
menu for that option will appear.
Use the + ( ) or - ( ) buttons to adjust the option settings.
press the ENTER ( ) button to save.
When you have made your changes,
To
press the MENU ( ) button. All settings are automatically saved when the OSD
exit,
menu closes.
Contrast
Phase (VGA only)
Select to reduce or
eliminate horizontal
distortion lines.
Select to increase or
decrease image contrast.
注意
: 色温度 ( ▶ P.19)
P24
☞
でダイレクトを選択し
ている場合は変更でき
ません。
To automatically
adjust, use the RESET
option.
(VGA only)
Brightness
Pitch
Select to increase
or decrease image
brightness.
Select to reduce or
eliminate vertical
distortion lines.
注意
: 色温度 ( ▶ P.19)
でダイレクトを選択し
ている場合は変更でき
ません。
P24
☞
To automatically
adjust, use the Reset
option.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Horizontal Center(VGA only)
Menu Position
Select to move the screen
image left or right.
Select to move the OSD
menu around the display.
To automatically adjust,
use the Reset option.
Vertical Center
Reset
Provides two options:
Use Auto Adjust to
reset only the image
parameters. Use Recall
to reset all screen options
to the factory default.
Selecting the exit (
(VGA only)
Select to move the screen
image up or down.
To automatically adjust,
use the Reset option.
) icon exits the Reset
window without resetting anything.
Color
Provides settings for
Backlight
9300°, 6500°, and 5000°
Kelvin.
Also provides a User
option that enables you
to adjust red, blue and
green independently.
Selects to increase or
decrease the backlight
brightness level.
Selecting DIRECT displays the received signal
as it is without any adjustment. Choose a setting
to work with and press Enter to activate your
selection. You can
Language
change the user setting
by selecting the icon ' '.
In the User
Adjustment window,
change red, blue and
Select to choose a
language option for the
OSD: English, Deutsch,
Francais, Espanol,
Italiano, or Japanese.
green to calibrate color.
To exit, select the icon ' '.
Remote Wake Up
オンにすると、
Energy Star の規格を
満たさなくなります。
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the LCD Monitor
(VGA only)
Adjusting Pitch and Phase
Some computers and video cards may not allow the multi-sync function to fully
work when DTU-710 is first connected. If some portion of the text appears
blurred, adjust the pitch and phase by following the procedure below. For crisp
images, set the DTU-710 resolution of your video card to 1280 x 1024.
From the Wacom Tablet Control Panel, select the CALIBRATION tab.
If you are working with multiple monitors, be sure the display corresponding
to the DTU-710 is selected in the MONITOR menu.
1.
Click on the CALIBRATE... button to display the monitor calibration screen.
2.
Adjustment pattern
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the OSD controls, open the OSD Menu and select the PITCH icon.
Adjust the Pitch level so the pattern of fine vertical stripes displays evenly.
3.
4.
5.
In the OSD Menu, select the Phase icon and adjust the Phase level so the
adjustment pattern shows clearly.
After completing the adjustments press the ENTER ( ) button and MENU ( )
button to exit the OSD Menu.
6.
Click on the Cancel button or press ESC to exit the calibration screen.
(1280 x 1024 resolution under Windows only): You can also adjust
Pitch and Phase in the closing Windows display.
Hint
If the pitch is not calibrated, vertical moire appears in the
darkened area. And if the phase is not calibrated, the darkened
area riffles.
Power Saving
DTU-710 conforms to VESA and Energy Star power saving guidelines. When
using DTU-710 with a VESA DPMS Display Power Management Signaling
(DPMS) compliant computer or graphics card, the display will automatically
comply with the below power saving parameters.
Power Saving Mode H-sync V-sync
Video Power Consumption Power Lamp
Power ON
Standby mode
Suspend mode
OFF mode
Yes
No
Yes
No
Yes
Yes
No
No
Active
Blanked
Blanked
Blanked
37W max.
2W max.
2W max.
1W max.
Blue
Orange/Blue
Orange/Blue
Orange
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for DTU-710
Cleaning
T
use a soft cloth with mild detergent (such
o clean the DTU-710 casing,
as dish washing liquid) diluted with water. Do not use paint thinner, benzine,
alcohol, or other organic solvents to clean DTU-710 casing or pen.
use a soft, dry cloth. If necessary, slightly
To clean the display screen,
moisten the cloth with water and try again. When cleaning, apply only a light
amount of pressure to the display screen and do not make the surface wet. Do
not use detergent to clean the display screen; this may damage the coating on the
screen. Please note that damage of this kind is not covered by the manufacturer's
warranty.
Replacing the Pen Tip
The pen tip will wear with normal use. When the nib gets too short, you can
replace it with one of the extra nibs that came with your pen. If the pen tip wears
and becomes angular, it may damage the coating on the cover glass of DTU-710
Interactive Pen Display. To avoid this, periodic nib replacement is recommended.
To insert a new nib:
To remove the old nib:
Clasp it with a pair of tweezers
or similar instrument and pull
the old nib straight out of the
pen.
Slide it straight into the barrel of
the pen. Firmly push the nib until it
stops. The new nib will slide into the
correct position.
CAUTION
Prevent your children from swallowing the pen nib or side switch. The pen nib
or side switch may accidentally be pulled out if children are biting on them.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you encounter problems with DTU-710 display, refer to the following tables. Your
problem may be described here, and you can try the solution offered.
For additional information about color issues, refer to the documentation that came with
your operating system or applications.
Display Troubleshooting
General Display Problems
Problem
The following message appears
Hint
The input signal frequency is incorrectly set or not
●
●
■
briefly on your display screen:
compatible with the DTU-710. Connect a different display
and set the refresh rate (vertical frequency) to some value
between 50 and 75 Hz. If your video card driver supports
djustment of the horizontal frequency, make sure it is set to
some value between 30 and 80 kHz.
The resolution is set too high (1280 x 1024, maximum).
The refresh rate is set too high (75 Hz maximum).
■
■
■
■
Set the display properties to detect plug and play monitors.
Check the video cable for bent or broken connector pins.
The following message ppears
briefly on your display screen:
Then properly connect the video cable.
Your computer may be in a power management mode.
Touch the pen tip to the display screen, move the mouse, or
depress any key on your keyboard.
■
■
Verify that the graphics card is properly installed.
The power LED is lit orange or
●
●
flashes orange and blue.
The following message ppears
Check that your computer is turned on.
■
■
briefly on your display screen:
Verify that you are using the video cable that came with
DTU-710.
Check that the DTU-710 video cable is fully connected.
Check the video cable and any video adaptors for bent or
broken connector pins. Then properly connect the video
cable and any necessary adaptors.
■
■
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
No display. The power LED is off.
Hint
Check that the AC power adaptor is plugged into both the
●
■
■
pen display tablet and an active power outlet, and that the
DTU-710 power switch is turned on.
Check the contrast, brightness, and backlight cntrols.Adjust
No display. The power LED is lit
●
blue.
as necessary, or open the OSD menu, go to the RESET menu
and select the RECALL option.
Do not extend the video signal cable. Do not use an input
The image appears multiple times
●
■
■
on the display.
When a still image is displayed
selector switch box.
Use a screen saver or other power management feature.
●
for a long period of time without
refreshing the screen, an afterimage
remains for a short period of time.
The color white does not display as
Verify that the display is operating at the factory default
settings. If that is not sufficient, then adjust color as necessary.
For details on color management, refer to your operating
system and application documentation.
●
■
■
white.
Verify that the video cable and connector are fully connected.
VGA Problems
Problem
The display ripples or flickers.
Hint
Open the OSD menu, go to the RESET menu, and select the
●
■
■
AUTO ADJUST option. Then, if necessary, manually adjust
pitch and phase.
Verify that the display adaptor or video card matches the
specifications for the DTU-710.
Adjust the refresh rate in the Display Properties control
■
■
panel.
As necessary, adjust contrast or brightness, pitch and phase.
The display is not clear.
●
Set the display resolution of your video card to 1280 x 1024.
Open the OSD menu, go to the RESET menu, and select the
■
■
The display and LCD panel are not
●
lined up. The display size is not
correct.
RECALL option.
As necessary, adjust pitch and phase, and horizontal and
vertical position. Note that some video cards may not show
■
the display in proper sizing.
Open the OSD menu, go to the RESET menu, and select the
The display ripples or shows a
●
■
■
moire pattern. The display color is
not even.
RECALL option.
As necessary, adjust PITCH and PHASE.
P.24
☞
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Pen Tablet Troubleshooting
General Problems
Problem
The computer does not have an
Hint
Check if there is an available USB port on a USB hub. If
●
●
■
available USB port.
none are available, you will need to add a USB hub or USB
card.
Make sure the pen display tablet power switch is turned on.
The tablet power LED is off.
■
■
Check that the AC power adaptor is plugged into both the pen
display tablet and an active power outlet.
Always be sure to use only the power adaptor that came with
the pen display tablet; other adaptors may cause damage to
■
■
your product.
The tablet driver software was not installed or did not load
The pen works only in mouse
mode, and does not draw with
pressure sensitivity.
●
properly.
Make sure the tablet driver software is installed and functioning.
Install the driver software for the pen tablet in accordance
with the instructions found in the Installation section of this
■
■
manual.
Open the tablet control panel and go to the PEN tab.
The pen selects everything or will
●
●
■
■
not stop drawing.
Double-clicking is difficult.
Move the TIP FEEL slider toward FIRM.
Be sure you are quickly tapping the display screen twice
in the same place on the pen display tabletʼs active area.
Using the side switch (when equipped) to double-click is a
recommended method.
Try increasing the DOUBLE-CLICK DISTANCE.
Try using a lighter TIP FEEL.
■
■
Windows: You might also consider turning on the Web style
interface so that you can navigate using a single click of the
pen.
The eraser selects everything or
Open the tablet control panel and go to the PEN tab. Move
●
●
■
■
will not stop erasing.
There is a delay at the beginning of
the ERASER FEEL slider toward FIRM.
Try decreasing the DOUBLE-CLICK DISTANCE.
pen strokes when using the pen for
drawing or selecting.
The pen tip does not function.
Be sure you are using the pen (modelUP-911E) that originally
came with your pen display tablet. Other pens may not
function properly on the DTU-710 pen display tablet.
Make sure the status LED lights blue when the tip is pressed.
Verify also that the USB cable is plugged in; the LED will not
light if the USB cable is not plugged into an active port. If the
LED does not light, you may have defective hardware.
●
■
■
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
You have to press hard with the pen
Hint
Open the tablet control panel and go to the PEN tab. Move
●
■
■
when clicking or drawing.
The side switch does not work.
the TIP FEEL slider toward SOFT.
Be sure you are using the pen (model UP-911E) that
originally came with your pen display tablet. Other pens may
not function properly on the DTU-710 pen display tablet.
Be sure you press the side switch when the pen tip is in
proximity – do this without pressing down on the pen tip.
From the tablet control panel, verify that the side switch is set
to the proper function you are expecting to occur.
Make sure the status LED lights blue when you press the
side switch. Verify also that the USB cable is plugged in; The
LED will not light if the USB cable is not plugged into an
active port. If the LED does not light, you may have defective
hardware .
●
■
■
■
The pen tip and screen cursor do
Open the tablet control panel and select the CALIBRATE tab.
●
■
■
not properly line up.
The screen cursor moves but it does
Continue with Calibrating the DTU-710 on page 14.
Make sure the pen tablet driver has loaded properly by
opening the tablet control panel. If the driver did not load,
you will see an error message. If an error message appears,
reboot your computer. If the problem persists, refer to the
appropriate Installation instructions for your platform and
reinstall the pen tablet software.
●
not jump to the pen tip location.
When the pen is placed on the
display screen, and it does not
follow the pen tip when the pen is
moved across the display.
If you have customized the side switch (when equipped)
on your pen to toggle between pen mode and mouse mode,
make sure that your pen display tablet is operating in pen
mode. See Button Functions, beginning on page 12, for more
information.
■
■
The line you are drawing does not
To function properly, some applications require that the pen
●
line up with the location of the
is set to pen mode. Make sure the pen has not been toggled to
mouse mode.
screen cursor in paint applications.
If the pen is set to pen mode and the problem still exists,
then you may have a corrupted preferences file. Follow the
■
■
instructions in the next tip to create a new preferences file.
When the pen is not in use, place it on the pen rest, in the
The screen cursor jumps back
●
when using your regular mouse or
trackball.
pen storage compartment, or at some location near the pen
display tablet, but not on the display. Leaving your pen
on the pen display tablet may interfere with screen cursor
positioning when using other input devices.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
If you have tried the previous
Hint
Windows: Do a Search or Find for the TABLET.DAT file
●
■
■
solutions, and the screen cursor
and pen tip still do not line up, the
preferences file may be corrupted.
Follow the procedure for your
platform to delete the preferences
file.
and delete it. The file should be located in your Windows or
Windows\System32 folder. Then restart your computer. When
the pen tablet driver loads, it will create a new preferences file
with the factory default settings. Recalibrate the unit.
Macintosh OS X: For a single user, delete the tablet
preferences by first choosing your HOME folder from the GO
menu. Then open your home LIBRARY folder. Within your
home LIBRARY folder, open the PREFERENCES folder and
delete the COM.WACOM.TABLETPREFERENCES file.
Log out, then log back in. When the tablet driver loads it will
create a new preferences file with the factory defaults.
For multiple users, delete all tablet preferences by first
opening the main APPLICATIONS folder. Then open the
TABLET folder and run the REMOVETABLET utility. When
the utility starts, click on the REMOVE ALL PREFERENCE
FILES button. Log out, then log back in. When the tablet
driver loads, it will create new preferences files with the
factory defaults.
Note: Do not manually remove the WACOM
TABLET.PREFPANE file from the main LIBRARY
PREFERENCEPANES folder. This file is only to be removed
when uninstalling the tablet software driver, and then only
when using the REMOVETABLET utility.
You can use your pen to control the other monitors in mouse
When using the pen display tablet
on a multiple monitor system, you
cannot use the pen to control the
other monitor(s).
●
■
mode. To use mouse mode, first set the penʼs side switch
button (when equipped) to MODE TOGGLE.... Then use
the switch to toggle between pen mode and mouse mode.
See
on page 11 and Button Functions,
Customizing the Pen
beginning on page 12.
When you are not using the pen, remove it from the pen
display tablet surface or the tablet will continue to send data,
The computer does not go to sleep.
●
●
■
■
keeping the computer awake.
The tablet portion of the DTU-710 emits electromagnetic
The screen cursor moves erratically
or jumps around on the display
screen when another tablet is
connected to your computer.
waves at a certain frequency. If another tablet is too closely
placed to the DTU-710 it may interfere with screen cursor
positioning. If this occurs, move the tablet further away from
the DTU-710.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Windows-Specific Problems
Problem
Windows 98SE or Me:
Hint
On a multiple monitor system, the pen display tablet is
●
■
When working with multiple
monitors, the screen cursor
positioning is incorrect after
moving into the unmapped area of
the virtual desktop.
mapped to the virtual desktop (a rectangular area covering all
monitors). If your video display areas do not form a rectangle
because they are different sizes or they are not evenly aligned,
the screen cursor positioning will be incorrect after moving
into the unmapped area of the virtual desktop. To reestablish
the correct screen cursor position, lift the pen out of tablet
proximity and bring it back into proximity over an area of the
pen display tablet that is mapped to a display area.
You must use a mouse when working in a full screen DOS
Windows 98SE or Me:
●
●
■
■
Your pen does not function inside a
window.
full screen DOS window.
After pressing CTRL+ALT+DEL,
When the CLOSE PROGRAM dialog box (Windows 98SE
or Me) is active, the pen tablet will not work. Use your mouse
or keyboard to continue. When this dialog box is closed, you
the screen cursor cannot be
controlled with your pen.
can again use your pen to control the screen cursor.
Reboot the system after installing the pen display tablet on a
Windows XP:
●
■
After installing the pen display
tablet on a system with multiple
users, the pen tablet only works on
the primary user desktop.
system with multiple users.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Macintosh-Specific Problems
Problem
Hint
At startup, a dialog box appears
telling you that either the driver
failed to load or the tablet
The pen tablet was not detected at startup. Make sure the
USB interface cable is securely connected and that the status
LED on the tablet turns on when the pen tip is pressed against
the tabletʼs active area.
●
●
■
preferences have not yet been
created.
The pen display tablet works
There may be a problem in the KEXT.CACHE file.
1. Unplug the pen display tabletʼs USB cable from your
computer. (Be sure to unplug only the USB cable.) Then
uninstall the tablet driver. See Uninstalling the DTU-710 on
page 41 for details.
■
correctly when initially installed
under OS v10.2.7 or 10.2.8, but
fails to work after restart.
2. Within your computerʼs OS X SYSTEM folder, select
(highlight) the LIBRARY folder. Then access folder
information by typing COMMAND+i.
3. Select and unlock OWNERSHIP & PERMISSIONS. Then
change the owner from “system” to “yourself (userʼs name)”.
Now lock it back up, entering you administrator password
when prompted.
4. Open the LIBRARY folder. Delete the EXTENSIONS.
KEXTCACHE and EXTENSIONS.MKEXT files.
5. Empty the trash.
6. Again select the LIBRARY folder and access the folder
information.
7. Again select and unlock OWNERSHIP & PERMISSIONS.
Then change the owner from “yourself (userʼs name)” to
“system” and lock it back up.
8. Close the window and restart your computer. When the
system is ready, plug the pen display tabletʼs USB cable back
into your computer.
Install the pen tablet driver and test the unit. It should work
normally when you restart your computer.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General Specifications
Physical dimensions (WxDxH):
Weight:
418x362x57mm (excluding the stand)
6.2kg (including the stand)
DC12V
Main Unit input Voltage:
Power consumption:
37W or less (DC12V)
Operating temp. & humidity:
Storage temp. & humidity:
5 to 35 deg. C, 20 to 80%RH (non condensing)
10 to 60deg. C, 20 to 90%RH (non condensing)
(maximum storage humidity is 38% at 60 deg.C,
-
and maximum storage temperature is 42 deg. C at
90% humidity)
LCD Display
Display:
a-Si TFT active matrix LCD
17 inch
Screen size:
Resolution (75Hz Max.)
1280x1024 pixels (SXGA), 1024x768 pixels
(XGA), 800x600 pixels (SVGA), 640x480 pixels
(VGA)
Pixel pitch:
0.264(W) x 0.264(H)mm
253 levels: 16,194,277 colors
Analog RGB / Digital signals (DVI 1.0)
Synchronous frequency: Horizontal 30 to 80kHz,
Vertical 50 to 75Hz
Color depth:
Signal Inputs:
All scan modes are non-interlaced.
50 to 75Hz
Refresh Rate
Plug and Play
DDC2B
On a TFT liquid crystal display, a very small number of pixels may be permanently illuminated or
not illuminated at all. This does not mean that the display is defective.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Tablet
Reading technology:
Active area:
Electromagnetic reasonance method
337.9 x 270.3mm
100
Resolution:
lpmm (0.01mm) max.
Accuracy:
+/-0.5mm, four corners ( 7 mm wide, 25 mm
long from each corner of four "L" shaped areas)
to be +/-1.0mm
Maximum reading height:
Maximum report rate:
Pressure levels:
5mm
133 points/sec., max
512 levels
Communication interface:
USB or RS-232C serial
Power Adaptor
Input voltage:
100 to 240 VAC, 50/60 Hz
12 VDC, 4.16 A
Output voltage:
Pen (UP-911E)
Pen tip travel:
0.1 mm (0.004 in) or less
Eraser tip travel:
2 mm (0.08 in), approximately
14.0 x 159.0 mm, 16g (0.63 x 6.26 in, 0.56 oz)
Rocker switch
Physical dimensions, weight:
Side switch type:
Pen Accessories
Extra nib:
PSI-A021
PST-A026
Pen holder:
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining Technical Support
If you have a problem with DTU-710, first check the appropriate setup chapter in this
guide to make sure the unit is installed correctly. Then review the Troubleshooting
section within this manual and the online Help; your problem may be described there
and you can try the solution offered. You can also check the product FAQs (Frequently
Asked Questions) on the Wacom web site.
Support Staff
If you think your DTU-710 Interactive Pen Display is not working properly, contact the
Wacom authorized distributors in your area (Check your area distributor on the Wacom
Asia
Tel: ++81-3-3371-1595 (English)
Fax: ++81-3-3371-1468 (English)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright © WACOM Company, Limited, 2004
All rights reserved. No part of this manual may be reproduced except for your express personal use. WACOM reserves the right to
revise this publication without obligation to provide notification of such changes. WACOM does its best to provide current and accurate
information in this manual. However, WACOM reserves the right to change any specifications and product configurations at its discretion,
without prior notice and without obligation to include such changes in this manual.
TRADEMARKS
WACOM is a registered trademark of WACOM Company, Limited. Macintosh is a registered trademarks of Apple Computer, Inc., regis-
tered in the U.S. and other countries. Microsoft, Windows are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or oth er countries. Any additional company and product names mentioned in this documentation may be trademarked
and/or registered as trademarks. Mention of third-party products is for information purposes only and constitutes neither an endorsement
nor a recommendation. WACOM assumes no responsibility with regard to the performance or use of these products.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
