Volvo Lawn Mower G726B User Manual

VOLVO MOTOR GRADER  
G726B  
ALL WHEEL DRIVE  
Configuration: Articulated frame  
• Single lever “Smart Shifter” transmission  
control with gear memory feature  
• 8400 fully sequential direct drive powershift  
transmission  
Engine model: Volvo D7DGDE2  
• Separate hydraulic pump & speed sensor  
for each front wheel  
• Choice of fully enclosed, ROPS cab in full  
height or low profile configuration, or  
ROPS canopy  
Maximum net engine output  
@2200 RPM (per SAE J1349):  
198 - 235 hp (148 - 175 kW)  
• Variable aggression for job matching  
• Moveable Blade Control System  
• Maintains aggression at both front wheels  
through turns  
Base weight: 35,400 lb (16 057 kg)  
• Load sensing, Closed Center Hydraulic  
System  
Blade down force:  
17,854 lb (8 099 kg)  
• Creep feature allows hydrostatic drive at  
front wheels from 0-2.0 mph (0-3,2 km/h)  
for optimum fine grading  
• Fully adjustable control pedestal with low  
effort hydraulic controls  
Blade pull:  
All Wheel Drive – 28,019 lb (12 709 kg)  
Tandem – 20,519 lb (9 307 kg)  
• Wheel motor efficiencies maintained in both  
forward and reverse  
• Full front and rear frame sections designed  
for attachment mounting  
• AWD available at speeds up to 20.2 mph  
(32,5 km/h)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
All Wheel Drive  
(continued)  
All Wheel Drive  
(continued)  
Front axle  
Type: Fully welded steel truss, gusseted for  
torsional strength, oscillates on a single 3.5”  
(89 mm) diameter center pivot pin.  
Wheel lean. . . . . . . . . . . . . . . . . . . . . . . . . 15º R & L  
Oscillation . . . . . . . . . . . . . . . . . . . 16º up and down  
Ground clearance. . . . . . . . . . . . . . 24.0" (610 mm)  
in all tractive conditions. When AWD is  
selected, the engine will deliver maximum VHP  
horsepower regardless of the working gear  
being used.  
Typical operating pressure . . . . 3,000 psi (206 Bar)  
Maximum operating pressure. . 5,000 psi (344 Bar)  
Minimum operating pressure. . . . . 500 psi (34 Bar)  
Top speed . . . . . . . . . . . . . . 20.2 mph (32.5 km/h)  
Creep Mode speed . . . . . . . 0-2 mph (0-3.2 km/h)  
Maximum rim pull . . . . . . . . . . . 7,500 lb (3 402 kg)  
Volvo AWD motors maintain maximum  
efficiency in both forward and reverse.  
Operating modes  
All Wheel Drive or Tandem Drive  
• On-Off Selection  
• Creep Mode - Hydrostatic front wheel drive  
only for optimum control and manouverability  
while fine grading.  
Two 3" (76 mm) diameter wheel lean cylinders  
and lock valve are standard equipment.  
• Manual Mode - Allows the operator to match  
front wheel agression setting to specific  
applications.  
All Wheel Drive  
The Volvo high torque All Wheel Drive System  
operates in forward gears 1-7 and reverse  
gears 1-4. The operator may shift from 7th  
AWD into 8th and back to 7th AWD at any  
time for maximum high speed performance.  
The Volvo high torque All Wheel Drive System  
incorporates two variable displacement, closed  
loop piston pumps. The Volvo AWD design  
automatically adjusts hydraulic flow and  
pressure to the drive system to match tandem  
wheel speeds in all tractive conditions. Each  
front wheel is independently powered by a 2  
speed motor. Each motor is controlled by its  
own speed sensor and pump. The All Wheel  
Drive system is controlled by the operator  
through a positive On/Off switch as well as a  
16 position variable aggression dial. The front  
wheel speed sensors will always match front  
wheel speed to tandem wheels speed relative  
to the level of aggression selected by the  
operator. This provides optimum job matching  
AWD features  
• Maximum startup torque  
• Power maintained in either direction  
• Smooth operation in low speeds  
• Maintains front wheel agression in turns  
• One speed sensor at each front wheel  
• Hydrostatic Creep Mode feature  
In addition, the Volvo system provides the  
operator with the ability to fine grade in Creep  
Mode using only hydrostatic front wheel drive.  
The Volvo high torque All Wheel Drive System  
offers infinite speed control below 2 mph (3,2  
km/h) for fine grading as well as a top speed  
of 20.2 mph (32,5 km/h) for snow plowing.  
The AWD controller is integral with the  
electronic 8400 transmission controller,  
thereby supplying the same diagnostic  
features found in the Volvo 8400 transmission.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Circle drive  
Steering  
Cab & controls  
Hydrostatic power front wheel steering  
incorporating two steering cylinders. Meets  
SAE J1511 OCT. 90 with optional secondary  
steering.  
Minimum turning radius using front axle steering,  
articulation, wheel lean and unlocked differential  
. . . . . . . . . . . . . . . . . . . . . . . . . . . 25'6" (7 772 mm)  
Steering arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72º  
Frame articulation angle . . . . . . . . . . . . . . . . . . . 22º  
The Volvo dual cylinder Circle Drive System  
uses direct acting hydraulic power for  
exceptional turning and holding capability  
under full load. Circle Drive System uses  
hardened drive pinions and is protected  
against impact damage by an overload cushion  
valve as standard equipment.  
Hydraulic drive cylinders . . . . . . . . . . . . . . . . . . . . . 2  
Points of leverage . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360º  
All controls are located in a 90° arc forward  
and to the right of the operator. Located  
forward of the operator are the engine oil  
pressure, coolant temperature and fuel level  
gauges, transmission gear indicator and a  
multi-function Contronic monitoring display.  
Located in the fully adjustable steering  
pedestal are the following switches: differential  
lock/unlock, hazard lights, combination turn  
signal, horn and high beam headlight. Heater  
and wiper/washer controls, lighting and  
accessory switches are grouped in the  
operator’s right hand console. This console  
Articulation lock standard.  
Drawbar  
Frame  
also  
contains  
the  
ignition  
key  
Fully welded box section. Narrow “T” design  
permits optimum visibility to the work area.  
Drawbar ball stud provides an adjustment to  
compensate for different tire sizes. Blade lift  
cylinder anchors are straddle mounted on  
drawbar to provide maximum strength and  
support.  
Dimensions of  
box section . . . . . . . . . 6.5" x 6.5" (165 x 165 mm)  
Plate thickness . . . . . . 1.0" & 0.75" (25 & 19 mm)  
and access to the circuit breaker and fuse  
panel. Located to the right of the operator,  
above the console, are the AWD On/Off  
switch, a 16 position variable aggression dial  
and the hydrostatic Creep On/Off switch.  
An accelerator/decelerator foot pedal and  
slider type hand throttle are standard  
equipment. Outside mounted rear view mirrors  
(L&R) are standard. Interior operator noise  
level ranges from 78 to 81 dB(A) per ISO  
6394 (enclosed cab).  
Full front and rear frame sections.  
Front: Fully welded box section. Dual sloped  
front frame provides excellent forward visibility.  
Minimum dimensions of  
box section . . . . . . . 10.5" x 14.0" (267 x 356 mm)  
Plate thickness . . . . . . . . . . . . . . . . . 0.75" (19 mm)  
Vertical section modulus  
at arch . . . . . . . . . . . . . . . . . . 119 cu in (1 950 cm3)  
minimum . . . . . . . . . . . . . . . 101.5 cu in (1 663 cm3)  
maximum . . . . . . . . . . . . . . . . 212 cu in (3 474 cm3)  
Linear weight - minimum-maximum . . . . . . . . . . . . . .  
107.1 - 232.5 lb/ft (159.4 - 346.0 kg/m)  
Cab options  
Moldboard  
• High capacity heater/air conditioner c/w  
adjustable vents, temperature control and 3  
speed fan  
Rear: Full perimeter rear frame permits modular  
powertrain mounting for ease of service and is  
ideal for attachment mounting. Optional first user  
lifetime warranty on frame and articulation joint.  
Standard moldboard with  
replaceable end bits . . . . . . . . . . . . 12' x 25" x 7/8"  
(3 658 x 635 x 22 mm)  
Blade material . . . . . . . SAE 1050 high carbon steel  
Edge: through hardened . . . . . 6" x 5/8" boron steel  
(152 x 16 mm)  
Bolt spacing. . . . . . . . . . . . . . . . . . . . . 6" (152 mm)  
• bolt size . . . . . . . . . . . . . . . . . . . . . . 5/8" (16 mm)  
• Fully adjustable, suspension seat  
• Lower opening front windows  
Minimum dimensions of  
rear frame . . . . . . . . . 4.0" x 10.0" (102 x 254 mm)  
Plate thickness . . . . . . . . . . . . . . . . . . 0.5" (13 mm)  
• Rear windshield wipers and washers  
• Lower front window wipers and washers  
• Modular, 24 volt radio and cassette player  
with remote control  
Articulation  
Slide rails supported by DURAMIDE™  
bearings.  
• Operator Convenience Package (lunch box,  
steel vacuum bottle and holder, ashtray)  
Twin 4.5" (114 mm) hydraulic cylinders  
articulate frame 22º right and left. Anti-drift lock  
valve ensures stable operation.  
Blade range:  
Moveable Blade Control System  
• 24 volt to 12 volt convertor for electrical  
accessories or two way radio installations  
Full height cab with ROPS  
Inside dimensions  
Height . . . . . . . . . . . . . . . . . . . . . 74.0" (1 880 mm)  
Width @ controls . . . . . . . . . . . . 56.0" (1 422 mm)  
Depth @ controls . . . . . . . . . . . . 55.5" (1 410 mm)  
(Dimensions shown with standard moldboard)  
Circle  
LEFT  
RIGHT  
Reach outside tires - articulated  
frame .......120.0" (3 048 mm)....119.5" (3 035 mm)  
Reach outside tires - straight  
Hardened teeth, cut on the outside of the circle  
for maximum leverage and minimum wear.  
An optional Low Profile Cab is available with  
an inside height of 62" (1 575 mm). All Volvo  
Grader cabs and canopies are designed to  
meet or exceed SAE J1040 APR. 88, ISO  
3471/1-1986(E), and 86/295/EEC ROPS  
requirements. The seatbelt is 2" (51 mm) wide  
and meets SAE J386 JUNE 93; ISO 6683-  
1981(E).  
The circle is supported at six points by three  
adjustable clamp plates and three adjustable  
guide shoes, providing optimum circle support  
and load distribution. DURAMIDE™ faced  
clamp and guide shoes prevent metal-to-metal  
contact and provide maximum service life.  
frame..........79.5" (2 019 mm)..........79" (2 007 mm)  
Blade slide ...26.5" (673 mm)..........26.5" (673 mm)  
Circle side  
shift ................30.5" (775 mm)..........29.5" (749 mm)  
Maximum bank  
sloping angle........................90º...................................90º  
Blade ground clearance.....................17.5" (445 mm)  
Blade cutting depth.............................32.0" (813 mm)  
Blade tilt range............................44º forward 6.5º back  
DURAMIDE™ is a synthetic bearing material  
that maximizes service life and reduces circle  
system maintenance requirements.  
Diameter . . . . . . . . . . . . . . . . . . 66.25" (1 683 mm)  
Thickness . . . . . . . . . . . . . . . . . . . . 1.25" (32 mm)  
Adjustable guide shoes. . . . . . . . . . . . . . . . . . . . . . 3  
Adjustable clamp plates . . . . . . . . . . . . . . . . . . . . . 3  
Superior blade mobility permits steep ditch  
cutting angles and back sloping without  
putting the front tire on the slope.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Load sensing hydraulics  
Capacities  
Closed Center Hydraulic System senses load  
requirements and maintains system pressure  
350 psi (24 Bar) above the load pressure.  
U.S.Gal. Imp.Gal. Litres  
Fuel tank . . . . . . . . . . 100.0 . . . . . 83.3. . . . . 378.5  
Transmission . . . . . . . . 10.0 . . . . . . 8.4. . . . . . 38.0  
Final drive. . . . . . . . . . . . 6.0 . . . . . . 5.0. . . . . . 23.0  
Tandems (each) . . . . . . 26.4 . . . . . 22.0. . . . . 100.0  
Hydraulic oil tank . . . . . 35.4 . . . . . 29.5. . . . . 134.0  
Coolant antifreeze protection to  
System features industry standard control  
arrangement complete with low effort,  
feathering type, short throw levers located on a  
fully adjustable control pedestal.  
-58º F (-50º C) approx. 12.4 . . . . . 10.3. . . . . . 47.0  
Engine oil . . . . . . . . . . . . 5.0 . . . . . . 4.2. . . . . . 19.0  
System incorporates lock valves to prevent  
cylinder drift under load in the following  
circuits: blade lift, moldboard tilt, circle shift,  
wheel lean and articulation.  
Attachments  
Hydraulic system features include axial piston  
pump, pressure and flow compensated,  
variable displacement with high output for  
smooth multi-functioning.  
“A” Frame. . . . . . . . . . . . . . . . . . . 700 lb (318 kg)  
Snow  
Hydraulic Wing  
• high-bench. . . . . . . . . . . . . . . 4,800 lb (2 177 kg)  
• low bench . . . . . . . . . . . . . . . 4,000 lb (1 814 kg)  
One Way Plow. . . . . . . . . . . . . 2,350 lb (1 067 kg)  
“V” Snow Plow  
Maximum pressure . . . . . . . . . . 2,700 psi (186 Bar)  
Output 2200 RPM. . . . 0-75 U.S. gpm (0-284 lpm)  
Filtration . . . . . . . . . . . . . . . . 10 micron spin-on type  
• 9' (2 743 mm). . . . . . . . . . . . 2,500 lb (1 134 kg)  
• 10' (3 042 mm) . . . . . . . . . . 2,650 lb (1 202 kg)  
Earth  
Dozer Blade  
• 8' (2 438 mm). . . . . . . . . . . . 2,620 lb (1 188 kg)  
• 9' (2 743 mm). . . . . . . . . . . . 2,870 lb (1 302 kg)  
•10' (3 048 mm) . . . . . . . . . . . 3,120 lb (1 415 kg)  
Front Mounted Scarifier. . . . . . 1,780 lb (807 kg)  
Mid-mount Scarifier . . . . . . . . . 1,725 lb (782 kg)  
Push Block. . . . . . . . . . . . . . . . 1,050 lb (476 kg)  
Ripper/Scarifier, rear . . . . . . . . 2,880 lb (1 306 kg)  
Windrow Eliminator . . . . . . . . . 1,300 lb (590 kg)  
Dimensions  
B
Overall width . . . . . . . . . . 8'4" (2 540 mm)  
A
Overall length. . . . . . . . 29'11" (9 119 mm)  
C Overall height . . . . . . . . . 11'2" (3 404 mm)  
• with Low  
D Wheelbase . . . . . . . . . . . 20'0" (6 096 mm)  
E
Bladebase  
Profile Cab . . . . . . . . . . . 10'2" (3 099 mm)  
• ISO 7134. . . . . . . . . . . . 8'6" (2 591 mm)  
F
Tread width. . . . . . . . . . . 6'10" (2 083 mm)  
C
O
V
E
R
A
L
L
H
E
I
G
H
T
E - BLADEBASE  
F - TREAD WIDTH  
D - WHEELBASE  
A - OVERALL LENGTH  
B - OVERALL WIDTH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STANDARD FEATURES  
Volvo “High Torque” All Wheel Drive with hydrostatic  
Creep feature  
Hardened circle teeth cut on outside of circle for  
maximum turning power  
Suspension seat  
100 U.S. gallon (378.5 l) fuel tank capacity  
Dual leaning wheel cylinders  
Operator controlled, lock/unlock differential final  
drive  
Hardened circle drive pinions for maximum wear  
resistance  
DURAMIDE™ wear strips on circle clamp plates and  
guide shoes prevent metal-to-metal contact for  
maximum service life  
4 wheel, crossover, dual braking system with reserve  
power assist  
Isolation mounted cab, transmission and engine for  
reduced noise and vibration  
Park brake with operator warning alarm and  
indicator  
Adjustable steering control pedestal with tilt head  
for maximum operator comfort  
Hinged radiator guard for easy trash clean out  
Backup lights  
Fully sequential, direct drive, powershift 8400  
transmission, with transmission guard  
Gauges include: coolant temperature, engine oil  
pressure, fuel, hourmeter, dash mounted air  
cleaner service indicator, articulation angle  
indicator, multi-function Contronic Monitoring  
System with visual and audible warnings  
Backup alarm with automatic volume levels  
Painted high gloss Volvo yellow and gray  
13.5" (343 mm) diameter, 4 plate, full oil master  
clutch  
Lockable tool box with storage space for scarifier  
shanks  
Moveable Blade Control System for optimum blade  
mobility  
Load sensing, Closed Center Hydraulic System with  
short throw, low effort control levers. Hydraulically  
operated blade lift, circle turn, moldboard slide  
and tilt, circle shift and wheel lean functions.  
Engine side panels complete with locks  
Left and right outside rear view mirrors  
Interior rear view mirror  
Full front and rear frame sections designed to  
withstand shock loading of rear attachments  
Circle drive counter-balance valve protects circle  
drive against impact damage  
Exhaust aspirated air cleaner  
Front cab wiper and washer  
Feathering type controls for precise blade  
adjustments  
OPTIONAL EQUIPMENT  
lb  
kg  
lb  
kg  
lb  
kg  
Accumulators - blade lift (2). . . . . . . . . . . 122  
Air conditioner - 29,000 BTU  
• HFC-134a (non-CFC refrigerant) . . . . . 130  
Brush guards . . . . . . . . . . . . . . . . . . . . . . . 40  
Cab  
• canopy shell with ROPS - deduct . . . (625) (284)  
• FOPS protection for ROPS cabs . . . . . 220 100  
• Low Profile Cab  
with ROPS - deduct . . . . . . . . . . . . . . (270) (122)  
Cab heater - 49,000 BTU • with cab  
pressurizer and replaceable filter. . . . . . . 60  
Defroster fans . . . . . . . . . . . . . . . . . . . . . . . . 3  
Engine block heater . . . . . . . . . . . . . . . . . . . 3  
Engine precleaner - Turbo II . . . . . . . . . . . . . 6  
First user lifetime frame warranty . . . . . . . . . 0  
Float control - right and left detent style  
independent, electric . . . . . . . . . . . . . . . . 15  
Hydraulic manifold cover . . . . . . . . . . . . . . 10  
Hydraulic tank heater . . . . . . . . . . . . . . . . . . 3  
24 volt radio/cassette player . . . . . . . . . . . . 6  
Lights  
55  
• Front mounted plow lights - 2  
Reflectors - rear/side . . . . . . . . . . . . . . . . . . . -  
Remote lube manifold for articulation  
cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . 0  
Remote valve for attachments  
• 3 or 5 bank - remote mount. . . . . . . . . . . 85  
Sideshift accumulator. . . . . . . . . . . . . . . . . 50  
Rim locks included with 3 piece rims. . . . . . 0  
Secondary steering (power assisted) . . . . 95  
Tie down brackets . . . . . . . . . . . . . . . . . . 100  
Tires  
-
• high mount. . . . . . . . . . . . . . . . . . . . . 120  
• low mount . . . . . . . . . . . . . . . . . . . . . 100  
• Headlights with dimmer switch . . . . . . . . . 0  
• Moldboards lights - 2. . . . . . . . . . . . . . . . . 2  
• Rear flood lights - 2 . . . . . . . . . . . . . . . . . . 2  
• Snow wing lights - 2 . . . . . . . . . . . . . . . . . 2  
Fenders  
• Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80  
• Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 182  
Moldboards  
• 14' x 25" x 7/8"  
(4 267 x 635 x 22 mm) . . . . . . . . . . . . 240 109  
Moldboard extensions  
R or L - 2' (610 mm). . . . . . . . . . . . . . . 190  
Moldboard edges - carbide 3/4" x 5"  
(19 x 127 mm) . . . . . . . . . . . . . . . . . . . . . . -  
100 amp alternator. . . . . . . . . . . . . . . . . . . . 0  
Operator convenience package  
54  
45  
0
1
1
59  
18  
0
39  
23  
0
43  
45  
1
36  
27  
1
1
3
0
• 17.5 x 25, 12 PR, G-2,  
14" (356 mm) rims. . . . . . . . . . . . . . . 375 170  
Tool kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -  
Transmission sump heater . . . . . . . . . . . . . . . -  
Tropical protection . . . . . . . . . . . . . . . . . . . . . -  
Vandalism protection . . . . . . . . . . . . . . . . . . 8  
Wheel weights for rear  
-
-
-
86  
4
7
4
1
3
-
0
wheels only - each . . . . . . . . . . . . . . . . 250 113  
Window - opening - lower front. . . . . . . . . . . -  
Window - opening sliders - left/right. . . . . . . -  
Wiper and washer - rear . . . . . . . . . . . . . . . . -  
Wiper and washer - lower front. . . . . . . . . . . -  
-
-
-
-
• lunch box, steel vacuum bottle  
and holder, ashtray. . . . . . . . . . . . . . . . . . 10  
Paint - custom colors. . . . . . . . . . . . . . . . . . . -  
Polar protection . . . . . . . . . . . . . . . . . . . . . . 0  
5
-
0
• Beacon (amber or blue). . . . . . . . . . . . . . 10  
• Clearance lights front & rear . . . . . . . . . . . 2  
4
1
Your safety and the safety of those around you depends on using care and judgement when operating and servicing your grader.  
Do not operate the grader until you read and understand the warnings and instructions in the operator’s manual. Volvo Motor  
Graders Limited is an ISO 9001 and 14001 registered company. www.volvo.com  
Under our policy of continuous product development and improvement, we reserve the right to change specifications and design  
without prior notice. The illustrations do not necessarily show the standard version of the machine.  
Consult your Volvo dealer for recommended option and attachment selection.  
Ref. No. 21 4 434 1005  
English  
Printed in Canada 2002.08-2.5 GRD  
Volvo, Goderich  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Teac Radio SR LX5i User Manual
Technika CRT Television LCD26 209X User Manual
Texas Instruments Calculator TI 83 User Manual
Texas Instruments Network Card TNETE2201 User Manual
Thermador Refrigerator KBULT3655E User Manual
TP Link Security Camera TL SC2020 User Manual
Tricity Bendix Cooktop SB416 User Manual
Video Products Computer Hardware VOPEX HDMI 2 LC User Manual
ViewSonic Flat Panel Television VPW505 User Manual
Vision Fitness Bicycle E4100 User Manual