VocoPro Car Amplifier HV 1200 User Manual

��

�

��

� � �

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

HV-1200

Professional High Power Vocal Ampliﬁer

o w n e r ' s

m a n u a l

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC Information

CAUTION:

READ THIS BEFORE OPERATING YOUR UNIT

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!: This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Vocopro may void your authority, granted by the FCC, to

use this product.

1. To ensure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install your unit in a cool, dry, clean place - away from

windows, heat sources, and too much vibration, dust,

moisture or cold. Avoid sources of hum (transformers, v

motors). To prevent fire or electrical shock, do not

expose to rain and water.

2. IMPORTANT: When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable(s) supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your

FCC authorization to use this product in the U.S.A.

3. Do not operate the unit upside-down.

4. Never open the cabinet. If a foreign object drops into

the set, contact your dealer.

3. NOTE: This product has been tested and found to

comply with the requirements listed in FCC Regulations,

Part 15 for Class "B" digital devices. Compliance with

these requirements provides a reasonable level of

assurances that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices. This equipment

5. Place the unit in a location with adequate air

circulation. Do not interfere with its proper ventilation;

this will cause the internal temperature to rise and may

result in a failure.

generates/uses radio frequencies and, if not installed

and used according to the instructions found in the

owner's manual, may cause interference harmful to the

operation of other electronic devices. Compliance with

FCC regulations does not guarantee that interference

will not occur in all installations. If this product is found

to be the source of interference, which can be

determined by turning the unit "Off" and "On", please try

to eliminate the problem by using one of the following

measures:

6. Do not use force on switches, knobs or cords. When

moving the unit, first turn the unit off. Then gently

disconnect the power plug and the cords connecting to

other equipment. Never pull the cord itself.

7. Do not attempt to clean the unit with chemical solvents:

this might damage the finish. Use a clean, dry cloth.

8. Be sure to read the "Troubleshooting" section on

common operating errors before concluding that your

unit is faulty.

Relocate either this product or the device that is being

affected by the interference.

9. This unit consumes a fair amount of power even when

the power switch is turned off. We recommend that you

unplug the power cord from the wall outlet if the unit is

not going to be used for a long time. This will save

electricity and help prevent fire hazards. To disconnect

the cord, pull it out by grasping the plug. Never pull the

cord itself.

Use power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter(s).

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300-ohm ribbon

lead, change the lead-in to coaxial type cable.

10. To prevent lightning damage, pull out the power cord

and remove the antenna cable during an electrical

storm.

If these corrective measures do not produce satisfactory

results, please contact your local retailer authorized to

distribute Vocopro products. If you can not locate the

appropriate retailer, please contact Vocopro, 1728

Curtiss Court, La Verne, CA 91750.

11. The general digital signals may interfere with other

equipment such as tuners or receivers. Move the

system farther away from such equipment if

interference is observed.

NOTE:

Please check the copyright laws in your country

before recording from records, compact discs,

radio, etc. Recording of copyrighted material may

infringe copyright laws.

CAUTION

The apparatus is not disconnected from the AC power

source so long as it is connected to the wall outlet,

even if the apparatus itself is turned off. To fully ensure

that the apparatus is indeed fully void of residual power,

leave unit disconnected from the AC outlet for at least

fifteen seconds.

Voltage Selector (General Model Only)

Be sure to position the voltage selector to match the

voltage of your local power lines before installing the

unit.

110V

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening for a Lifetime

Selecting fine audio equipment such as the unit youʼve just purchased is only the start of your

musical enjoyment. Now itʼs time to consider how you can maximize the fun and excitement your

equipment offers. VocoPro and the Electronic Industries Associationʼs Consumer Electronics

Group want you to get the most out of your equipment by playing it at a safe level. One that lets

the sound come through loud and clear without annoying blaring or distortion and, most

importantly, without affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing “comfort level” adapts to a higher volume of

sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard

against this by setting your equipment at a safe level BEFORE your hearing adapts.

To establish a safe level:

• Start your volume control at a low setting.

• Slowly increase the sound until you can hear it comfortably and clearly, and without

distortion.

Once you have established a comfortable sound level:

• Set the dial and leave it there.

• Pay attention to the different levels in various recordings.

Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all,

we want you listening for a lifetime.

Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since

hearing damage from loud noise is often undetectable until it is too late, this manufacturer and

the Electronic Industries Associationʼs Consumer Electronics Group recommend you avoid

prolonged exposure to excessive noise. This list of sound levels is included for your protection.

Some common decibel ranges:

Level

Example

Quiet library, Soft whispers

Living room, Refrigerator, Bedroom away from traffic

Light traffic, Normal Conversation

Air Conditioner at 20 ft., Sewing machine

Vacuum cleaner, Hair dryer, Noisy Restaurant

Average city traffic, Garbage disposals, Alarm clock at 2 ft.

The following noises can be dangerous under constant exposure:

Level

Example

100

120

140

180

Subway, Motorcycle, Truck traffic, Lawn Mower

Garbage truck, Chainsaw, Pneumatics drill

Rock band concert in front of speakers

Gunshot blast, Jet plane

Rocket launching pad

-Information courtesy of the Deafness Research Foundation

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Instructions

8. Ventilation - The appliance should be situated so its

location does not interfere with its proper ventilation.

For example, the appliance should not be situated on a

bed, sofa, rug, or similar surface that may block the

ventilation slots.

CAUTION

RISK OF SHOCK

9. Heat - The appliance should be situated away from

heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers)

that produce heat.

CAUTION: To reduce the risk of electric

shock, do not remove cover (or back). No

user-serviceable parts inside. Only refer

servicing to qualified service personnel.

10. Power Sources - The appliance should be

connected to a power supply only of the type

described in the operating instructions or as marked

on the appliance.

Explanation of Graphical Symbols

The lightning flash & arrowhead

symbol, within an equilateral triangle,

is intended to alert you to the

presence of danger.

11. Grounding or Polarization - Precautions should be

taken so that the grounding or polarization means of

an appliance is not defeated.

12. Power-Cord Protection - Power-supply cords

should be routed so that they are not likely to be

walked on or pinched by items placed upon or

against them, paying particular attention to cords at

plugs, convenience receptacles, and the point where

they exit from the appliance.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and servicing instructions.

13. Cleaning - Unplug this unit from the wall outlet

before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning.

WARNING

To reduce the risk of fire or electric shock, do

not expose this unit to rain or moisture.

14. Power lines - An outdoor antenna should be

located away from power lines.

1. Read Instructions - All the safety and operating

instructions should be read before the appliance is

operated.

15. Nonuse Periods - The power cord of the appliance

should be unplugged from the outlet when left unused

for a long period of time.

2. Retain Instructions - The safety and operating

instructions should be retained for future reference.

16. Object and Liquid Entry - Care should be taken so

that objects do not fall and liquids are not spilled into

the enclosure through openings.

3. Heed Warnings - All warnings on the appliance and in

the operating instructions should be adhered to.

17. Damage Requiring Service - The appliance should

be serviced by qualified service personnel when:

4. Follow Instructions - All operating and use

instructions should be followed.

A. The power supply cord or plug has been damaged; or

B. Objects have fallen into the appliance; or

C. The appliance has been exposed to rain; or

D. The appliance does not appear to operate normally

or exhibits a marked change in performance; or

E. The appliance has been dropped, or the enclosure

damaged.

5. Attachments - Do not use attachments not

recommended by the product manufacturer as they

may cause hazards.

6. Water and Moisture - Do not use this unit near water.

For example, near a bathtub or in a wet basement and

the like.

18. Servicing - The user should not attempt to service

the appliance beyond that described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

7. Carts and Stands - The appliance should be used

only with a cart or stand that is recommended by the

manufacturer.

Note:

7 A. An appliance and cart combination

should be moved with care. Quick stops,

excessive force, and uneven surfaces may

cause an overturn.

To CATV system installer's (U.S.A.): This reminder is

provided to call the CATV system installer's attention to

Article 820-40 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the

cable ground shall be connected as close to the point of

cable entry as practical.

Download from Www.Somanuals.com. All Manuals Search And Download.

Welcome

And thank you for purchasing the HV-1200 from VocoPro, your ultimate choice in

Karaoke entertainment! With years of experience in the music entertainment business,

VocoPro is a leading manufacturer of Karaoke equipment, and has been providing

patrons of bars, churches, schools, clubs and individual consumers the opportunity to

sound like a star with full-scale club models, in-home systems and mobile units. All our

products offer solid performance and sound reliability, and to reinforce our commitment

to customer satisfaction, we have customer service and technical support professionals

ready to assist you with your needs. We have provided some contact information for

you below.

VocoPro

1728 Curtiss Court

La Verne, CA 91750

Toll Free: 800-678-5348

TEL: 909-593-8893

FAX: 909-593-8890

VocoPro Company Email Directory

Customer Service & General Information

[email protected]

Tech Support

[email protected]

Remember Our Website

Be sure to visit the VocoPro website www.vocopro.com for the latest information on

new products, packages and promos. And while you're there don't forget to check out

our Club VocoPro for Karaoke news and events, chat rooms, club directories and even

a KJ Service directory!

We look forward to hearing you sound like a PRO, with VocoPro, the singer’s ultimate

choice.

FOR YOUR RECORDS

Please record the model number and serial number below, for easy reference, in case of loss or theft. These

numbers are located on the rear panel of the unit. Space is also provided for other relevant information

Model Number

Serial Number

Date of Purchase

Place of Purchase

Download from Www.Somanuals.com. All Manuals Search And Download.

Speciﬁcations

INPUT Speciﬁcations

INPUT

CONNECTION

LEVEL(RATED)

-50dBu

IMPEDANCE

1.3 Kohm

Mic 1-4

XLR (BAL)

1/4” (BAL/UNBAL)

RCA JACK

MUSIC

0dBu

10Kohm

(AV1-AV4)

Mic LOOP

RETURN(tip)

Music LOOP

L/R RETURN

(TIP)

1/4” (unbal)

0dBu

10Kohm

OUTPUT Speciﬁcations

OUTPUT

CONNECTION

BINDING POST

LEFT/RIGHT

(+:RED,-:BLACK)

RCA JACK

LEVEL

IMPEDANCE

4 ohm

AMP OUTPUT

(THD <0.1%)

296Watt X 2

PREOUT

+4dBu

10 Kohm

L/R

MIC OUTPUT

(mic out VR max)

SUB WOOFER

(sub woofer VR max)

1/4” PHONE (unbal)

XLR (balanced)

0dBu

10 Kohm

+6dBu

0dBu

1/4” PHONE (unbal)

XLR (balanced)

+6dBu

Music 0dBu Input L or R

,music master VR max,

music G.EQ center, 60Hz

set)

MIC LOOP OUTPUT

SEND (TIP)

1/4” PHONE(unbal)

1/4” PHONE

0dBu

10 Kohm

200 ohm

MUSIC LOOP OUTPUT

SEND (TIP)

0dBu

HEAD PHONE OUTPUT

135mV

POWER CONSUMPTION

AC 120V , 8.9 A

(@ RATED POWER)

DIMENSIONS

W X H X D

INNER BOX

SHIPPING BOX

19” x5.2” x16.1”

484 x132 x409mm

21.7” x8.7” x20.5

550 x220 x520mm

22” x9.1” x20.9”

560 x230 x530mm

WEIGHT

NET:

34.4 lbs (15.6kg)

SHIPPING:

39.2 lbs (17.8kg)

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started

Thank you for purchasing the HV-1200. Take a few moments to look through this manual. Before setting up, please

make sure the following items are included.

• HV-1200

• Power Cable

��

�

��

� � �

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Returns and Warranty

In the unlikely event that the HV-1200 would need to be shipped for repair, it is recommended that you keep all the product

packaging and receipt. For detailed warranty information, please visit www.vocopro.com/warranty_extended.html. To ﬁnd a

VocoPro Authorized Service Center near you, please visit www.vocopro.com/servicecente r .html

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Connected

Connection diagram

��

�

��

�

��

�

��

�

��

�

��

�

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Connected cont.

Connecting Power

��

�

What you will need:

�

��

• Surge Protector (recommended) or power outlet

• Included power cable

��

To connect Power to the HV-1200

��

1. Connect one end of the power cable to the rear

panel of the HV-1200.

2. Connect the other end of the power cable to the

power outlet or surge protector.

Connecting Speakers

The Speaker Terminals are located on the rear panel. Be sure to connect the left channel (L), right channel (R), “+”

(red) and “--” (black) properly.

• Before connecting the speakers, make sure that the HV-1200 is

disconnected from the power source.

• Do not let the bare speaker wires touch each other or another metal part

of this unit. This could damage the HV-1200 and/or the speakers.

Preparing the Speaker Cable

You can either use an exposed speaker wire or Banana Plug speaker cable.

Using Exposed Speaker Wire

1. Remove approximately 3/8” (10mm) of insulation.

2. Twist the exposed wires together to prevent short circuits.

3. Loosen the knob on the speaker terminal.

4. Insert the bare wire.

5. Tighten the knob until the wire is secure.

�

��

Using Banana Plugs

��

1. Plug the Banana Connector into the jack,

ensuring that the red and black connections

are aligned.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Connected cont.

Determining the proper way to connect the speaker cables:

The speaker cable is a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps

with a stripe, groove or ridges.

1. Connect one end of the striped (grooved, ridged, etc.) cable to the

“+” (red) terminal on the rear panel of the HV-1200.

2. Connect the other end of the striped (grooved, ridged, etc.) cable

��

to the “+” (red) terminal on the speaker.

3. Connect one end of the “plain” (NO stripes, grooves, ridges, etc.)

cable to the “--” (black) terminal on the rear panel of the HV-1200.

4. Connect the other end of the “plain” (NO stripes, grooves, ridges,

etc.) cable to the “--” (black) terminal on the speaker.

Connecting a device to the PRE OUT jacks

��

�

��

The L/R (red and white) RCA PRE OUTPUT jacks on the rear

panel can be connected to any self-powered input device with RCA

inputs. (i.e. recording device, powered speakers, etc)

�

��

�

��

�

��

�

��

What you will need:

��

• Powered device with L/R RCA inputs

• RCA L/R audio cable (red & white)

��

1. Connect one end of the red and white RCA cable to the PRE

OUTPUT jacks on the HV-1200’s rear panel.

2. Connect the other end of the red and white RCA cable to the

RCA inputs on the recording device, powered speakers, etc.

��

Connecting a Powered Subwoofer

��

�

��

The HV-1200 has two types of connections for subwoofer output.

This is for compatibility with different types of subwoofers. See your

subwoofer instruction manual to determine if you need an XLR or

¼” cable.

�

��

�

What you will need:

• Powered Subwoofer

• XLR or ¼” cable

�

��

�

��

�

��

To connect a Powered Subwoofer to the HV-1200

1. Connect one end of the XLR or ¼” cable to the rear panel of

the HV-1200.

2. Connect the other end of the XLR or ¼” cable to the input on

the powered subwoofer.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Connected cont.

Connecting a Powered Vocal Monitor

��

�

��

The HV-1200 has two types of connections for mic-only

output. This is for compatibility with different types of powered

vocal monitors. See your powered vocal monitor instruction

manual to see if you need an XLR or ¼” cable.

�

��

�

What you will need:

• Powered Vocal Monitor

• XLR or ¼” cable

�

��

�

��

�

��

To connect a Powered Vocal Monitor to the HV-1200

1. Connect one end of the XLR or ¼” cable to the rear

panel of the HV-1200.

2. Connect the other end of the XLR or ¼” cable to the

input on the Powered Vocal Monitor.

��

Connecting to TVs/Video Monitors using the RCA Video (yellow) Outputs

��

There are three video outputs on the rear panel of the HV-

1200. All three connectors output the same video signal

which is selected by the AV selector button on the front

panel.

What you will need:

• Up to 3 TVs/Video Monitors with RCA video inputs

• RCA video cable(s) (yellow)

��

To connect TVs/Video monitors to the HV-1200

1. Connect one end of an RCA video cable to an RCA

video OUT jack on the HV-1200 rear panel.

�

��

�

��

2. Connect the other end of the RCA video cable to the

RCA video input on the TV/Video monitor.

3. Make sure the TV/Video monitor is set to the correct

video input. Consult the TV/Video monitor’s user

manual for the necessary instructions.

��

�

��

�

��

�

��

�

��

4. Repeat steps 1-3 for each additional TV/Monitor.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Connected cont.

Connecting External Players to the HV-1200

��

There are four Audio/Video input channels on the rear

panel of the HV-1200. This allows you to connect up to

four external players such as DVD players and CD+G

players to the HV-1200. You can switch between these

input channels using the AV selector button on the front

panel.

��

�

��

�

��

�

What you will need:

��

• Up to 4 external players with RCA outputs

• RCA Audio/Video cable(s) (yellow, red, white)

��

To connect external players to the HV-1200

1. Connect one end of an RCA Audio/Video cable to an

RCA Audio/Video OUT jack on the external player.

NOTE: Some players, such as CD players, do not

have video outputs. In this case, use only the Red

and White RCA connectors.

2. Connect the other end of the RCA Audio/Video cable

to an RCA input channel on the HV-1200 rear panel.

3. Repeat steps 1-2 for each additional player.

��

Connecting an External Vocal Effects Device

The HV-1200 has an effects loop which allows you to add additional effects to the microphone channels.

What you will need:

• External Effects Device

• Two ¼” Cables

To connect an External Effects Device to the HV-1200

1. Connect one end of one ¼” cable to the mic loop SEND jack on the rear panel of the HV-1200.

2. Connect the other end of this cable to the input on the external effects device.

3. Connect one end of the next ¼” cable to the output of the external effects device.

4. Connect the other end of this cable to the mic loop RETURN jack on the rear panel of the HV-1200.

NOTE: Your effects device may have a different type of input and output jack. You may need a different type of

cable or an adapter to make this connection. Refer to your effects device instruction manual.

Connecting an External Music Effects Device

The HV-1200 has an effects loop which allows you to add additional effects to the music signal.

What you will need:

• External Effects Device

• Two Paired ¼” Cables

To connect an External Effects Device to the HV-1200

1. Connect one end of one paired ¼” cable to the music loop SEND jack on the rear panel of the HV-1200.

2. Connect the other end of this cable to the input on the external effects device.

3. Connect one end of the next paired ¼” cable to the output of the external effects device.

4. Connect the other end of this cable to the music loop RETURN jack on the rear panel of the HV-1200.

NOTE: Your effects device may have a different type of input and output jack. You may need a different type of

cable or an adapter to make this connection. Refer to your effects device instruction manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Connected cont.

Connecting Microphones

The HV-1200 has four microphone input channels. Each channel has two types of microphone jack for compatibility with

different types of microphone cables.

What you will need:

• Up to four Microphones

• XLR or ¼” Mic Cables

To connect Microphones to the HV-1200

1. Connect one end of the mic cable to the microphone.

2. Connect the other end to a mic channel’s ¼” jack or XLR jack depending on the type of mic cable.

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Connecting Headphones

The HV-1200 has a headphone jack so you can monitor your mix.

What you will need:

• Headphones

To connect Headphones to the HV-1200

1. Connect headphones to the headphone jack on the front panel.

2. Adjust the volume to a comfortable level.

��

� � �

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Descriptions and Functions

�

��

�

��

� � �

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Front Panel

1. Microphone Input Channels - See page 16 for a detailed description.

2. Effect Controls - See page 17 for a detailed description.

3. Multiplex/Vocal Eliminator Button - This button cycles through the vocal cancel options. Use Multiplex (MPX) to

remove vocals from multiplexed audio sources, such as multiplex CDs and CD+Gs. Use the Vocal Eliminator function

to reduce the presence of vocals on non-multiplex audio sources.

NOTE: The Vocal Eliminator function does not work with every type of music. It reduces the frequencies most

commonly associated with human singing and vocals.

4. Key Display - Displays the number of the current key control step. +8 is the highest key control step, and -8 is the

lowest. 0 indicates that no key adjustment is being made.

5. Key Control Buttons - Use these buttons to change the key of the music. The UP button will raise the key of the

music, and the down button will decrease the key of the music. Pressing the normal button will turn off the key

control adjustments.

6. Graphic Equalizer - This GRAPHIC EQ is used to BOOST and/or CUT particular frequencies. Each slide fader

processes a particular frequency range indicated by the number below it. Frequencies from 125Hz - 250Hz

constitute the very low to low range. Frequencies from 250Hz to 1kHz are the mid-range and frequencies from

1kHz to 8kHz make up the high to very high range. To adjust, slide the fader up to boost the frequency presence

and down to cut the frequency presence.

7. AV Select - Use these buttons to select the Audio/Video source. Pressing AV1 will select the AV1 input on the back

panel, AV2 will select the AV2 input on the back panel, etc. The LEDs above the buttons light to indicate which input

has been selected.

8. Headphone Output - Attach headphones to this output to monitor the mix. Use the level control to adjust the

volume of the headphones.

9. Compressor - The compressor automatically adjusts and maintains the signal levels on the microphone channels.

This allows you to avoid unexpected audio peaks in the speaker output.

10. Master Microphone Effect Control - Controls the amount of effect applied to all the microphone channels.

11. Master Microphone Volume Control - Controls the volume of all the microphone channels.

12. Master Music Volume Control - Controls the volume of the music.

13. Power Switch - This switch turns the HV-1200 ON and OFF.

Download from Www.Somanuals.com. All Manuals Search And Download.

Descriptions and Functions cont.

�

� �

�

��

�

��

�

��

�

��

�

Microphone Input Channels

1. ¼” Microphone Input Jack - Use this jack to connect a wired microphone with a ¼” mic cable.

2. XLR Microphone Input Jack - Use this jack to connect a wired microphone with an XLR mic cable.

3. Signal Indicator LED - This LED will light when an audio signal is present on this channel.

4. Level Control - Use this control to adjust the volume of the microphone audio on this channel.

5. High Control - Use this control to boost or cut the high end frequencies of the microphone audio on this channel.

6. Middle Control - Use this control to boost or cut the middle frequencies of the microphone audio on this channel.

7. Low Control - Use this control to boost or cut the low end frequencies of the microphone audio on this channel.

8. Effects Control - Use this control to increase or decrease the amount of effects applied to this microphone channel.

9. Peak Indicator LED - This LED will light when this microphone channel is peaking or too loud.

Download from Www.Somanuals.com. All Manuals Search And Download.

Descriptions and Functions cont.

��

�

��

�

��

� � �

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

Effect Control

1. Echo Level Control - Use this control to increase or decrease the volume of the echo effect that is applied to the

microphone channels.

2. Reverb Level Control - Use this control to increase or decrease the amount of the reverb effect that is applied to

the microphone channels.

3. Echo Delay Control - This control increases or decreases the amount of time between each echo repetition.

4. Echo Repeat Control - This control adjusts how long the echo lasts.

5. Hiss Filter - This control is used to decrease hiss on the mic channels.

Download from Www.Somanuals.com. All Manuals Search And Download.

Descriptions and Functions cont.

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

Rear Panel

1. RCA Audio/Video Input Channels - Use these jacks to connect your audio and video devices.

2. RCA Video Outputs - Use these jacks to output a video signal to TVs or monitors.

3. ¼” Music Loop Jacks - Use these jacks to add an external effects device to process the music signal.

4. ¼” Mic Loop Jacks - Use these jacks to add an external effects device to process the microphone signal.

5. Microphone Output Jacks - Use these jacks to output the microphone signal only. Use the output level control to

adjust the level of the output. Turn clockwise to increase and counter-clockwise to decrease.

6. Subwoofer Output Jacks - Use one of these jacks to connect to a powered subwoofer. Use the output level control

to adjust the level of the output. Turn clockwise to increase and counter-clockwise to decrease.

7. Speaker Output Terminals - Use these terminals to connect to your speakers.

NOTE: Only connect one speaker per side.

8. AC Power Input - Connect the power cord here.

9. AC Fuse Plug - Open this cover to replace a blown fuse.

NOTE: Replace fuse only with same type as marked on the rear panel.

10. L/R RCA Pre-Amp Output - Use this line level output to connect to a recording device.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Customizing Source Music Output

Using KEY CONTROL

If a song’s natural musical key is either too high, or too low to be sung comfortably, use the KEY CONTROL

feature to bring the musical key into range.

• Press the UP button to raise the key a ½ step

• Press the DOWN button to lower the key a ½ step

• Press the NORMAL button to return the key to its natural position

There is a maximum of 8 steps in either direction (UP/DOWN.) The current setting is displayed in the KEY

DISPLAY (ex. -2, +3.)

Using VOCAL CANCEL (Multiplex) and VOCAL ELIMINATOR

To remove the lead vocals from a disc so a performer can sing along with the musical accompaniment, use

either the VOCAL CANCEL (Multiplex) or VOCAL ELIMINATOR features.

VOCAL CANCEL (Multiplex)

The VOCAL CANCEL feature is only available when playing a multiplex formatted audio track. Multiplex formatted

tracks have the music recorded to the LEFT channel, and the vocals recorded to the RIGHT channel.

• Press the MPX/V. ELIM button once to activate VOCAL CANCEL. When activated, the MPX LED will be

illuminated GREEN.

VOCAL ELIMINATOR

The VOCAL ELIMINATOR feature can be used to remove the lead vocals from standard stereo audio tracks*.

• Press the MPX/V. ELIM button twice to activate VOCAL ELIMINATOR. When activated, the V. ELIM LED will

be illuminated YELLOW.

*NOTE: The Vocal Eliminator feature may not work on all audio tracks; may not

completely remove the lead vocals; or may partially remove other musical elements

from the track.

Using the GRAPHIC EQUALIZER

Use the equalizer to ﬁne tune the musical signal for optimal sound reproduction and emphasis. For example, if

after applying Key Control, the music signal sounds less “bright,” you could use the graphic equalizer to restore

the high frequencies. Or, if you wanted to emphasize the bass of a particularly “thin“ sounding track, you use the

graphic equalizer to enhance the low frequencies.

��

�

��

�

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations cont.

Customizing Microphone Output

Using the HIGH/MID/LOW Controls

To adjust the sound of each connected microphone individually, use the HIGH/MID/LOW controls. These

controls work similar to the graphic equalizer, enabling to for the enhancement/suppression of particular

frequencies within each microphone channel.

• Adjust the HIGH control to increase/decrease sibilance.

• Adjust the MID control to increase/decrease presence.

• Adjust the LOW control to increase/decrease boom.

Using ECHO and REVERB Vocal Effects

Use the effect controls to add a sense of depth and spaciousness to the vocal signal.

ECHO

The ECHO effect adds depth to the vocals for a professional sound. To apply ECHO, follow the steps below:

• Set the MASTER EFFECT control to 5.

• For each mic channel where echo will be applied, set the EFX control to 5.

• Set the ECHO LEVEL control to 5.

• Set the ECHO DELAY and ECHO REPEAT controls to your liking.

• Set the ECHO LPF (low pass ﬁlter) to 5.

• Continue to make adjustments to the ECHO LEVEL/DELAY/REPEAT/LPF controls untill the ideal echo

effect is achieved.

REVERB

The REVERB effect adds a sense of space to the vocals for a rich and professional sound. To apply REVERB,

follow the steps below:

• Set the REVERB control to 3 as a starting point, and then adjust to your liking.

After you have customized the ECHO and REVERB effects, you can control

their application with the following controls:

• LEVEL MASTER control – Controls the overall effects level available to the microphone channels.

• EFX control – Controls the level of EFX (set by the LEVEL MASTER control)_applied to each microphone

channel.

NOTE: The LEVEL MASTER and EFX controls adjust both ECHO and REVERB effects simultaneously.

Using the COMPRESSOR Feature

The built-in COMPRESSOR feature automatically reduces very loud microphone signals or “peaks,” preventing

unfavorable sound levels from damaging your speakers, as well as your ears. When you notice a microphone

channel’s PEAK indicator lighting repeatedly, or suspect there may be peaks in the microphone signal, use the

compressor.

To apply compression, follow the steps below:

• Turn the COMP knob counter-clockwise to increase compression, and clockwise to disable compression.

During compression, the dB indicator LEDs will illuminate indicating how much

the signal was compressed; reduced in output strength.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

The HV-1200 does not turn on

• Make sure the HV-1200 is plugged in.

• Make sure the power cord is undamaged. If it is damaged, do not attempt to repair it, contact VocoPro

for a replacement cord.

• If the HV-1200 is plugged in to a power strip, make sure the power strip is turned on.

• Check the fuse. If the fuse is blown, replace only with the type marked on the back panel.

Troubleshooting Chart

PROBLEM

CAUSE

SOLUTION

No sound coming from

selected music source

Input Selector is set incorrectly

Change Input Selector to the

correct current playing source

Music Master Volume control is Raise Music Master Volume level

set to minimum

to an appropriate level

Speakers and Speaker Cables

are either not connected, loose

or malfunctioning

Check Speakers and Speaker

Cable connections. Tighten or

replace if necessary.

Source player is functioning

incorrectly

Replace player and reset the

HV-1200’s power supply

No graphic output from

display devices when

playing CD+G’s

Disc is not a CD+G

Insert a CD+G for playback

TV or monitor device is not set

to the correct video setting

Change TV or monitor settings

to accept video

Video cable(s) are not properly

connected

Reconnect cables ﬁrmly to

correct video jacks

High pitched squealing

occurs when using the

microphone

Microphone is pointed to, or

close to speakers

Move microphone away from

speakers

Treble level(s) are too high on

microphone channel(s)

Turn down treble level(s) on

microphone channel(s)

No microphone output is

present

The microphone is not turned on Turn on the microphone

The microphone cable is either

loose or not functioning

Tighten or replace the

microphone cable

The Microphone Volume for that Turn up the Microphone Volume

channel is set to minimum

for that channel

The microphone is not

functioning correctly

Replace the microphone

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

Download from Www.Somanuals.com. All Manuals Search And Download.

HV-1200 Owner’s Manual

v1.0

www.vocopro.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Tascam Musical Instrument GVI User Manual
Thermador Cooktop P24GE User Manual
Topfield DVR TF 5010 PVR User Manual
Toshiba DVD Player SD 3980 User Manual
TRENDnet Switch TK 205K User Manual
Troy Bilt Lawn Mower 769 06304 User Manual
Tunturi Home Gym E6R User Manual
Vector Air Compressor VEC255 User Manual
Vermont Casting Indoor Fireplace TBREF36 User Manual
Viking Electronics Answering Machine MLC 24 User Manual