Vizio DVR C DR161 CU User Manual

QUICK MANUAL

DIGITAL VIDEO

RECORDER

C-DR091 CU Series

C-DR161 CU Series

Thank you for purchasing TOA Digital Video Recorder. Please carefully follow the instructions in this

manual to ensure long, trouble-free use of your equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe

operation.

• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages

regarded as very important precautions are included.

• We also recommend you keep this instruction manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property

damage which could result from mishandling. Before operating your product, read this manual first and

understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

Do not expose the unit to rain or an environment where it may be

splashed by water or other liquids, as doing so may result in fire or

electric shock.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could

WARNING

result in death or serious personal injury.

When Installing the Unit

• This is a class A product. In a domestic environment this product may cause radio interference in which case

the user may be required to take adequate measures.

• Use the unit only with the voltage specified on the unit. Using a voltage higher than that which is specified

may result in fire or electric shock.

• Do not cut, kink, otherwise damage nor modify the power supply cord. In addition, avoid using the power

cord in close proximity to heaters, and never place heavy objects -- including the unit itself -- on the power

cord, as doing so may result in fire or electric shock.

• Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface.

Doing so may result in the unit falling down and causing personal injury and/or property damage.

When the Unit is in Use

• If any of the following irregularities occurs, immediately switch off the power, disconnect the power supply

plug from the AC outlet and inform the shop from where the unit was purchased. Further using the unit may

result in fire or electric shock.

· If you detect smoke or a strange smell coming form the unit

· If water or any metallic object gets into the unit

· If the unit falls, or the unit case breaks

· If the power supply cord is damaged (exposure of the core, disconnection, etc.)

· If no image appears

• To prevent a fire or electric shock, never open the unit case nor modify the unit as there are high voltage

components inside the unit. Refer all servicing to your nearest TOA dealer.

• Do not place cups, bowls, or other containers of liquid or metallic objects on top of the unit. If they

accidentally spill into the unit, this may cause a fire or electric shock.

• Do not insert nor drop metallic objects or flammable materials in the ventilation slots of the unit's cover, as

this may result in fire or electric shock.

• Do not touch the power supply plug or control line during thunder and lightning, as this may result in electric

shock.

• The socket-outlet shall be installed near the equipment and the plug (disconnecting device) shall be easily

accessible.

Download from Www.Somanuals.com. All Manuals Search And Download.

Indicates a potentially hazardous situation which, if mishandled, could

result in moderate or minor personal injury, and/or property damage.

CAUTION

When Installing the Unit

• Never plug in nor remove the power supply plug with wet hands, as doing so may cause electric shock.

• When unplugging the power supply cord, be sure to grasp the power supply plug; never pull on the cord

itself. Operating the unit with a damaged power supply cord may cause a fire or electric shock.When

removing the power cord, be sure to hold its plug to pull.

• When moving the unit, be sure to remove its power supply cord from the wall outlet. Moving the unit with the

power supply cord connected to the outlet may cause damage to the power supply cord, resulting in fire or

electric shock.

• Do not block the ventilation slots in the unit's cover. Doing so may cause heat to build up inside the unit and

result in fire.

• Avoid installing the unit in humid or dusty locations, in locations exposed to the direct sunlight, near the

heaters, or in locations generating sooty smoke or steam as doing otherwise may result in fire or electric

shock.

• Do not connect a network terminal exposed to excessive voltage to the 100BASE-TX terminal, Disk array

connection terminal or Remote control I/O terminal A, as doing so may result in fire or electric shock.

When the Unit is in Use

• Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal

injury and/or property damage. In addition, the object itself may fall off and cause injury and/or damage.

• Clean the unit periodically. Contact your TOA dealer regarding the cleaning. If dust is allowed to accumulate

in the unit over a long period of time, a fire may result.

• If dust accumulates on the power supply plug or in the wall AC outlet, a fire may result. Clean it periodically.

In addition, insert the plug in the wall outlet securely.

• Switch off the power, and disconnect the power supply plug from the AC outlet when cleaning or leaving the

unit unused for long periods of time. Doing otherwise may cause a fire or electric shock.

• An all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated in the

electrical installation of the building.

The equipment must be connected to an earthed mains socket-outlet.

-Finland

"Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan"

-Norway

"Apparatet må tilkoples jordet stikkontakt"

-Sweden

"Apparaten skall anslutas till jordat uttag"

Download from Www.Somanuals.com. All Manuals Search And Download.

CU version complies with Part 15 of the FCC Rules.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Modifications

Any modifications made to this device that are not approved by TOA Corporation may void the authority

granted to the user by the FCC to operate this equipment.

This equipment is classified as a LASER CLASS 1 PRODUCT. The following classification label is located on

the drive.

CLASS 1 LASER PRODUCT

CAUTION:

INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. NOMENCLATURE AND FUNCTIONS

[ C-DR161 Series Front ]

DVD

BUZZER STOP/

ALARM RESET

MENU/

ENTER

PRIORITY

ARCHIVE

REC

MULTI

REC

KEY LOCK

MONITOR

ZOOM

SCREEN

SEQUENCE

FAILURE

HD FULL

DIGITAL VIDEO RECORDER C-DR161

(9) Menu key

(1) Power key [

]

• Holding down the Menu key for 2 seconds or

more when in live mode displays the menu

screen on Monitor 1 screen.

Pressing the Power key changes the Digital

Video Recorder's mode from standby to

operation mode. To switch from operation mode

to standby mode, hold down the Power key for 2

seconds or more.

• Use this key when confirming selected setting

items on the menu screen.

• Holding down the Menu key for 2 seconds or

more when the Security setting is activated

displays the Password entry screen.

(2) Camera selector key

Pressing the Camera selector key displays the

corresponding camera image on the full screen.

(10) Sequence/ [ ] Key

(3) Priority recording key

• Pressing the Sequence key in live mode

causes the camera outputs to be displayed in

preprogrammed sequential order.

Used to start priority recording. To stop priority

recording, hold down the Priority recording key

for 2 seconds or more. The Priority recording

key flashes red during priority recording.

• Pressing the setting value on the Menu screen

during selection changes the setting value in

forward direction.

(4) Monitor key

Use this key when switching operation between

Monitor 1 and Monitor 2 outputs.

Monitor 1 output is enabled when the key is

unlit, and Monitor 2 output is enabled when the

key is lit.

(11) Reverse playback [

] key

• Images are played back in reverse if the

Reverse playback key is pressed.

• Use this key to move the cursor to the left on

the menu screen.

(5) Buzzer stop key (Alarm reset key)

Use this key to reset alarm event recording.

This key is also used to stop a buzzer tone.

(12) Pause [

] key

• Use this key to temporarily stop the playback

display. Operation can be performed for the

archive menu display, frame advance/reverse

playback, and instant event access playback

while the display is temporarily stopped.

(6) Zoom key

Use the Zoom key to zoom in on the live and

playback screens (2x zoom).

• Used this key to move the cursor upward on

the Menu screen.

(7) Search key

Use this key to search for recorded images.

(13) Stop [

] key

(8) Multi-Screen / [ ] Key

• Use this key to stop playback or reverse

playback.

• Display on the multi-segment split screen.

• Pressing this key while setting values are

selected on the menu screen varies setting

values in the reverse direction.

• Use this key to move the cursor downward on

the Menu screen.

(14) Playback [

] key

• Pressing the Playback key plays back

recorded images.

• Use this key to move the cursor to the right on

the Menu screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

[C-DR161 series Rear]

TERMINATION

OFF

RM IN-A

DISK ARRAY

OUT

ALARM IN

PRIORITY

CAMERA

RM IN-B

RM OUT-B

VIDEO

CONTROL OUT

TIME SYNC

AC MAINS

OUT

SER.

DIGITAL VIDEO RECORDER

model C-DR161D3 CU

OUT

AUDIO

110-120V

50/60Hz mA

LINK

MONITOR OUT

RS-232C

100BASE-TX

TOA Corporation

MADE IN JAPAN

(15) AC inlet

(22) Control input/output terminal

• Control output terminal

Outputs a signal during equipment failure

occurs.

Connect the supplied power cord to this socket.

(16) Monitor output terminal

• Monitor 1 output terminal

Outputs the Monitor 1's camera images.

• Priority recording input terminal

Use this terminal to begin Priority recording

using signals from connected external

equipment.

• Monitor 2 output terminal

Outputs the Monitor 2's camera images.

• Time sync input & output terminal

Use this terminal to synchronize the clocks of

multiple Digital Video Recorders used in the

system.

(17) Audio input/output terminal

• Audio input terminal

This terminal is used for audio recording.

• Audio output terminal

• Remote Control Input/Output Terminal B

Use this terminal for connection of the C-

RM1000 Remote Controller.

Outputs audio input terminal signals during live

screen display, and outputs the recorded audio

during playback display.

• Camera control terminal

Use this terminal to control the Combination

Camera.

(18) Video input terminal

Connect the camera to this terminal. Connecting

the camera automatically terminates the Digital

Video Recorder at 75 Ω.

Note

The C-RM1000 Remote Controller must be

connected to the Digital Video Recorder in

order to control the Combination Camera.

(19) Video output terminal

A loop through output for the Video input

terminal. Connecting the BNC plug to the Video

output terminal automatically cancels the 75Ω

termination.

(23) Remote controller input/output terminal A

( Power can be supplied.)

Use this terminal to connect the C-RM1000

Remote Controller.

(20) 10BASE-T/100BASE-TX terminal

Use this terminal to remotely monitor or control

cameras connected to the Digital Video

Recorder or search or play back their recorded

images through the network using the web

browser from a PC.

(21) Alarm input terminal

Use this terminal to make Alarm event

recording. Connect no-voltage contact signals of

sensors, etc. to this terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. CONNECTIONS

Combination camera

Disk Array

C-DA1000-2

RS-485

Color camera

DISK

ARRAY

TERMINATION

OFF

DISK ARRAY

RM IN-A

OUT

ALARM IN

PRIORITY

CAMERA

RM IN-B

RM OUT-B

VIDEO

CONTROL OUT

TIME SYNC

AC MAINS

OUT

Digital Video Recorder

C-DR161 Series

OUT

AUDIO

LINK

MONITOR OUT

RS-232C

100BASE-TX

MONITOR

OUT2

10BASE-T/

100BASE-TX

MONITOR

OUT1

Monitor 1

DVR CONTROL

OUTPUT-A

Live only

LAN

Monitor 2

Remote Controller

C-RM1000

PRIORITY

CAMERA

RM IN-B

RM OUT-B

CONTROL OUT

TIME SYNC

OUT

CAMERA

RS-485

C-DR091 and C-DR161 Series

C-DR091: 9 I/ O Terminals

C-DR161: 16 I/ O Terminals

: Coaxial cable (Video signal)

: CPEV-S 0.65 (RS-485 Control line)

Twisted pair with shield 22AWG or larger

Match the Combination Camera’ s address to the Digital Video

Recorder’ s video input number.

: Modular cable, 3 m (9.8 ft).

(supplied with the C-RM1000)

: Modular cable, 1 m (3.3 ft)

(supplied with Disk Array)

: eSATA cable, 1 m (3.3 ft)

(supplied with Disk Array)

Download from Www.Somanuals.com. All Manuals Search And Download.

4. EXTERNAL TERMINAL CONNECTIONS

4.1. Alarm Input Terminal Connections

The number of terminals available differs depending on whether the Digital Video Recorder is a 9-channel or a

16-channel version. Refer to the table below when making alarm input terminal connections.

For 16 channel

For 9 channel

ALARM IN

Terminal name

Symbol

Terminal name

Symbol

Name

Alarm input 1

Signal ground

Alarm input 2

Signal ground

Alarm input 3

Signal ground

Alarm input 4

Signal ground

Alarm input 5

Signal ground

Alarm input 6

Signal ground

Alarm input 7

Signal ground

Alarm input 8

Signal ground

Alarm input 9

Signal ground

ALARM 1

GND

ALARM 9

GND

Alarm input 10

Signal ground

Alarm input 11

Signal ground

Alarm input 12

Signal ground

Alarm input 13

Signal ground

Alarm input 14

Signal ground

Alarm input 15

Signal ground

Alarm input 16

Signal ground

ALARM 2

GND

ALARM 10

GND

ALARM 3

GND

ALARM 11

GND

ALARM 4

GND

ALARM 12

GND

ALARM 5

GNA

ALARM 13

GNA

ALARM 6

GND

ALARM 14

GND

ALARM 7

GND

ALARM 15

GND

ALARM 8

GND

ALARM 16

GND

4.1.1. Terminal connection

The terminal connector is unlocked by pressing down on its release button. To connect the cable, press down

on the release button first, insert the cable, then push the release button up again to lock the cable in place.

However, for solid cables with diameters from 0.8 mm(AWG20) to 1.2 mm(AWG16), there is no need to press

down on the release button. Cable can be connected simply by inserting it in place until it will not go any

further.

Note

Ensure that the cable is securely locked into the terminal after connection.

Press down the

Release button.

Applicable cable

Insert a cable.

• Solid conductor

AWG26 (ø 0.4 mm)

AWG16 (ø 1.2 mm)

Push the

• Stranded conductor

release button up.

AWG24 (0.2 mm²)

AWG20 (0.75 mm²)

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2. Control I/O Terminal Connections

The control input and output terminals include: priority recording terminal, camera control terminal, remote

controller input/output terminals, control output terminal, and time synchronization input/output terminals.

PRIORITY

CAMERA

RM IN-B

RM OUT-B

CONTROL OUT

TIME SYNC

OUT

Terminal name

PRIORITY IN

PRIORITY G

Terminal name B

CONTROL OUT 1

CONTROL OUT G

CONTROL OUT 2

CONTROL OUT G

CONTROL OUT 3

CONTROL OUT G

CONTROL OUT 4

CONTROL OUT G

TIME SYNC IN

Name

Priority Recording Input

Control Output 1

Priority Recording Ground

Not connected

Control Output Ground

Control Output 2

Camera Control (RS-485) +

Control Output Ground

Control Output 3

CAMERA

Camera Control (RS-485) Ground

CAMERA G

Camera Control (RS-485)

Control Output Ground

Control Output 4

CAMERA

Remote Control Input B + (RS-485)

Remote Control Input B Ground

RM IN-B

Control Output Ground

Date/Time Adjustment Input

Date/Time Adjustment Input Ground

Date/Time Adjustment Output

Date/Time Adjustment Output Ground

RM IN-B G

Remote Control Input B

(RS-485)

RM IN-B

Remote Control Output B + (RS-485)

Remote Control Output B Ground

RM OUT-B

TIME SYNC G

RM OUT-B G

TIME SYNC OUT

TIME SYNC G

Remote Control Output B

(RS-485)

RM OUT-B

Notes

• Ensure that the cable is securely locked into the terminal after connection.

• Use the CPEV-S cable (twisted pair shielded cable) with diameter larger than 0.65 mm for the Control

Input/Output terminal connections. Also be sure to connect the shielded cable to the GND terminal.

• The maximum cable length of the control cable from the Digital Video Recorder to the camera of which

termination is set to ON is 1.2 km. Also the maximum cable length of the control cable from the Remote

Controller to the Digital Video Recorder of which termination switch is set to ON is 1.2 km.

4.2.1. Time synchronization input/output terminal connections

Two different methods are available to synchronize the time, one using both master and slave units, the other

using NTP.

Note

When using a single-channel Digital Video Recorder, set the synchronization interval to "5 seconds."

Input Output

Master

Slave 1

Slave 2

Slave 7

To synchronize the times of slave units with the time of the master unit, connect the slave units to the master

unit in a series via their input and output terminals. In other words, connect the input of slave number one to

the master unit's output and the input of slave number two to slave number one's output, and so on.

4.3. 10BASE-T/100BASE-TX Terminal Connections

Use this terminal to remotely monitor or control cameras connected to the Digital Video Recorder, or search or

play back their recorded images on a PC web browser. When connecting a PC directly to the Digital Video

Recorder, use a network crossover cable. Use the straight-through cable for connection between them via a

switching hub.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. DIGITAL VIDEO RECORDER ACTIVATION AND TERMINATION

5.1. Recorder's Activation

1. Insert the power supply plug.

The Recorder is placed in standby mode. The power

key flashes at about 5-second intervals while in standby

mode.

Power key LED indicator Mode

Distinguishes Main power OFF

Note

Do not pull out the power supply plug while the Power

Flashes (5sec) Standby mode

During a system check

key is light green. Ensure that the Recorder is in the

standby mode when pulling out the power supply plug.

Logged data could be damaged or lost if the power

supply plug is pulled out during initialization (while

accessing the hard disk).

Flashes (1sec)

Lights

(during activation)

Power ON (during operation)

2. Press the Power key while the Recorder is in standby mode.

The Power key flashes green during a system check. The Power key changes from flashing to steady ON

after system check completion, allowing camera images to be displayed.

5.2. Recorder's Power Off and Disconnect

Hold down the Power key for 2 seconds or more. All operations stop, placing the Recorder in standby mode.

When moving the Recorder, be sure to place it in standby mode, then remove the power supply plug from the

wall outlet.

6. MAIN MENU SETTING

6.1. About the Main Menu Settings

To perform each setting, display the Menu screen when in live mode.

1. Holding down the Menu key for 2 seconds or more.

Displays the Menu screen.

M A

M E N U

R E C S E

N G

S P L A Y S E

N G

N E T W O R K S E

M A

S E

N G

Notes

S Y S

L O G

D A T

E M S E

N G

S P L A Y

M E S E

N G

• Menu screen is not displayed while the Monitor Output 2 is

selected. (while the Monitor key is lit).

M A

N T E N A N C E

M A G E A R C H

N G

• Display the Menu screen after returning to the live mode when

in playback mode.

• Menu screen is not displayed while in zoom mode and during

zoom display (while zoom key is lit)

2. To move the cursor, use the [

] and [

] keys.

The [ ] and [ ] keys can be used to move the cursor only when there are setting parameters.

3. To select or change parameters, use the [+] and [–] keys.

4. Press the Menu key at the mark at the desired setting item.

If no change has been made to the current parameter:

The screen moves to the next screen.

If changes have been made:

Save setting confirmation message is displayed. (Refer to the next page.)

5. To exit the setting and return to the previous screen, press the [

of the screen.

] key at the leftmost parameter position

A Save Setting confirmation dialog is displayed if changes have been made. If set value has not been

changed, the screen moves to the previous screen, Exits the Menu screen when the Main Menu screen is

displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

6.2. Setting Item List

MAIN MENU

Menu item

PRIORITY REC SETTING

Setting item

Main menu item

REC SETTING

PRIORITY REC INPUT MODE

AUDIO

POST TIME

AUTO REC SETTING

PRE-REC SETTING

SCHEDULE

GROUP A

F SETTING

NORMAL REC SETTING

ALARM EVENT

SPECIAL DAY SETTING

MOTION SETTING

AUDIO

REC SETTING

EVENT

ALARM EVENT

REC MODE

REC TIME

REC RATE

REC QUALITY

AUDIO

ALARM INPUT MODE

POST ALARM TIME

MOTION DETECT MODE

POST MOTION TIME

OVERWRITE

DISPLAY SETTING

CHARCTER DISPLAY SETTING

REC AUDIO

OVERWRITE

REC

MONITOR OUTPUT SETTING

SEQUENCE SETTING

CAMERA NAME SETTING

DVR NAME SETTING

MONITOR 1, 2 SCREEN

ALARM DISPLAY INTERVAL

PLAY

REMAINING

DISK MODE

DISK STATUS

DATE

NETWORK SETTING

IP ADDRESS

SUBNET MASK

TIME

DATE/ TIME

MONITOR 1 , 2 CAM NAME

DVR NAME

DEFAULT GATEWAY

WEB SERVER PORT

WEB USER PASSWORD

WEB ADMIN PASSWORD

WEB LIVE QUALITY

WEB MAX BIT RATE

PRIMARY DNS

SECONDARY DNS

NTP SERVER

(

)

TIME ZONE GMT

MAIL SETTING

SENDER ADDRESS

SEND-TO ADDRESS 1

SMTP SERVER

POP 3 AUTHENTICATION

ENCRYPTION

ACCOUNT NAME

PASSWORD

POP3 SERVER

TRANSMISSION SETTING

TEST TRANSMISSION

To next page

Download from Www.Somanuals.com. All Manuals Search And Download.

To previous page

Menu item

Setting item

Main menu item

PLAY DISK

SYSTEM SETTING

HD REMAINING TIME

BUZZER

I/O TERMINAL MODE

INPUT MODE

OUTPUT MODE

CTRL OUT TERMINAL

PRIORITY REC

ALARM REC

MOTION REC

HD FULL

HD ERROR

VIDEO LOSS

FAN FAILURE

SECURITY SETTING

CAMERA PRESET SETTING

CAMERA PROTOCOL

CAMERA BIT RATE

OPERATION LEVEL 1, 2, 3

USB KEY LEVEL

PRIORITY REC OPERATION LEVEL 3

REMOTE ACCESS LIMIT

LOGOUT INTERVAL

RS232C BIT RATE

RS232C FLOW CTRL

RS232C RESPONSE

CONTROLLER BIT RATE

CONTROLLER RESPONSE

DVR-ID

LANGUAGE SELECTION

LOG DISPLAY

REC LOG

FAILURE LOG

SYSTEM LOG

DATE/TIME SETTING

DATE/TIME ADJUST OPERATE

DATE/TIME ADJUST TIME

DATE/TIME ADJUST OUTPUT

DAYLIGHT SETTING

START DATE/TIME

END DATE/TIME

MAINTENANCE

DISK MODE

HD INITIALIZE

SETTING INITIALIZE

LOG INITIALIZE

EXPORT SETTING DATA

IMPORT SETTING DATA

USB KEY REGISTRATION

USB KEY DATA ERASURE

DISK ARRAY 1, 2

IMAGE ARCHIVING

START, END 1

CAMERA 1 16 , ALL

Download from Www.Somanuals.com. All Manuals Search And Download.

7. INITIAL SETTINGS

Be sure to perform the following settings before using the Digital Video Recorder. Failure to do so may lead to

incorrect operation of each function.

• DVR-ID setting (When cascade-connecting)

Note: When cascade-connecting the Digital Video Recorders, set the DVR-ID first. Otherwise, the Menu

screen is not displayed.

• Clock settings

• Hard disk initialization

• Auto-Recording settings

7.1. Setting the DVR-ID

When cascade-connecting the Digital Video Recorders, set different DVR-ID for all individual Digital Video

Recorders. DVR-ID are all factory-preset to "1." Follow the procedure below to set DVR number.

1. Press the Digital Video Recorder's Power key while holding down the Sequence key in standby mode.

Camera Selection keys 1 – 8 flashes for about 1minute.

2. Press the desired DVR-ID to set.

The selected number flashes three times, then the number is programmed as DVR-ID.

Note: It is impossible to operate the Digital Video Recorder when the main power is set to OFF. Operate the

Digital Video Recorder after placing it in standby mode.

7.2. Clock Settings

Perform clock settings of the Digital Video Recorder. Adjust the date and time in Clock Settings on the menu screen.

Notes

• If the clock setting is not performed, video recordings are not made according to the schedule set in the

auto-recording setting.

• In some cases, changing the current time may make it impossible to play back the recorded images

correctly when duplicated time data exists in the recording data.

M A

M E N U

D A T

M E S E

N G

R E C S E

N G

A N

S P L A Y S E

N G

N E T W O R K S E

M A

S E

N G

D A T

D A Y

M E A D

U S

O P E R A T

M E

O U T P U T

L A V E

S Y S

L O G

D A T

E M S E

N G

Menu key

S P L A Y

S E C

M E S E

N G

G H T

S E

N G

O N

M A

N T E N A N C E

T A R T D A T

M E

A P R

W E E K S U N

M A G E A R C H

N G

E N D D A T

M E

O C T

L A S

1. Hold down the Menu key for 2 seconds or more.

The main menu screen is displayed.

2. Move the cursor with the [

key.

The clock setting screen is displayed.

] and [

] keys to select "DATE/TIME SETTING," then press the Menu

3. Move the cursor with the [

] and [

] keys and perform clock settings using the [+] and [-] keys.

Set year, month, date, hour, minute, and second.

4. Press the [

] key while the cursor is set to the leftmost selection item on the screen.

The indication will appear to ask whether or not to save the setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Move the cursor with the [

] and [

] keys, select "YES," then press the Menu key.

The message requesting a reboot is displayed.

Note

There is no need to reboot the DVR if not synchronizing using the NTP server, though the message

requesting a reboot is displayed after the clock setting has been saved. (The changed setting is reflected in

the device without rebooting the DVR.)

6. Move the cursor with the [

] and [

] keys to select "NO," then press the Menu key.

The display reverts to the main menu screen.

7.3. Hard Disk Initialization

Set disk mode (normal mode and mirror mode) used for recording to the hard disk to initialize the hard disk.

Notes

• Since initializing the hard disk erases all recorded images, be sure to copy the necessary data to DVD-R

disk or USB memory before initialization.

• Disk mode is factory-preset to "NORMAL." Leave the disk mode as it is when using the Digital Video

Recorder in normal mode. However, it is recommended that the hard disk be initialized since recording

starts automatically when the Digital Video Recorder's power is switched on.

M A

N T E N A N C E

H D

A L

H D

S E

A L

S K M O D E N O R M A L

N G

A L

E X E C U T

E X E C U T E X E C U T

L O G

A L

S E

D A T A A R C H

D A T A R E A D

N G

H D D

–

M A S

E R

0 G B

L A V E

- - - - -

N G

D V D

Menu key

U S B K E Y R E G

T R A T

O N

U S B K E Y D A T A E R A S U R E

S K A R R A Y

U N U S E D

1. Hold down the Menu key for 2 seconds or more.

The main menu screen is displayed.

2. Move the cursor with the [

] and [

] keys to select "MAINTENANCE," then press the Menu key.

The Equipment Maintenance screen is displayed.

3. Select "HD INITIALIZE," then press the Menu key.

The Hard Disk Initialization screen is displayed.

4. Select the disk mode using the [+] and [

-] keys.

Select "NORMAL," or "MIRROR."

5. Move the cursor with the [ ] and [

"YES" and "CANCEL" are displayed.

] keys to select "EXECUTE," then press the Menu key.

6. Move the cursor with the [

] and [

] keys to select "YES," then press the Menu key.

Confirmation message is displayed after executing the hard disk initialization.

7. Select "OK," then press the Menu key.

The display returns to the hard disk initialization screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.4. Auto-Recording Settings

Recordings are normally performed according to the preprogrammed schedule. Therefore, perform schedule

or group settings when making auto-recording.

7.4.1. Schedule setting

Set the schedule (Day, Start time, and End time) for each group to operate.

Menu key

1. Hold down the Menu key for 2 seconds or more.

The main menu screen is displayed.

2. Select "REC SETTING," then press the Menu key. The Recording setting screen is displayed.

3. Move the cursor with the [

key.

] and [

] keys to select "AUTO REC SETTING," then press the Menu

The Auto-recording setting screen is displayed.

4. Select "SCHEDULE," then press the Menu key.

5. Move the cursor with the [

and [ ] keys.

Set a day of the week, Start time, End time and manner of operation (group setting).

], [

], and [

] keys and perform schedule setting using the [+]

6. Press the [

] key while the cursor is set to the leftmost selection item on the screen.

The indication will appear to ask whether or not to save the setting.

7. Move the cursor with the [

] and [

] keys to select "YES," then press the Menu key.

The display reverts to the auto-recording setting screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.4.2. Setting the group

Perform individual settings such as Normal recording and Alarm Event recording for Group A - F.

A U T O R E C S E

N G

G R O U P

–

S E

N G

S C H E D U L

N O R M A L R E C S E

N G

G R O U P

–

S E

N G

A L A R M E V E N T R E C S E

N G

A L A R M E V E N T R E C M O D E

S E Q U E N C E

E D G E

A L A R M

N P U T M O D E

A L A R M M E

O N D E E C T M O D E

M O T O N M E

P O S

M O T

P O S

S E C

Menu key

E V E

S E C

S P E C

A L D A Y S E

N G

M O T

A U D

O N S E

N G

O N

1. Choose "Group A-F" from the Auto-recording Settings and press the Menu key.

The Group setting screen is displayed.

2. Move the cursor with the [

and [ ] keys.

], [

], and [

] keys and perform Group setting using the [+]

3. Press the [

] key while the cursor is set to the leftmost selection item on the screen.

The indication will appear to ask whether or not to save the setting.

4. Move the cursor with the [

] and [

] keys to select "YES," then press the Menu key.

The display reverts to the auto-recording setting screen.

7.4.3. Other settings

In Auto-Recording Settings, "special day," "motion detection," and "audio (ON/OFF)" settings can be

performed in addition to both schedule and group settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

8. MONITOR DISPLAY

8.1. Full-Screen Display

Pressing the Camera Selector key while in live or playback mode displays the selected camera output on the

full screen.

Press the Camera

Selector key No. 3.

8.2. Multi-Segment Split-Screen Display

When the live or playback screen is displayed, the multi-segment split-screen display changes as shown

below each time the Multi-Screen key is pressed. Multi-Screen key lights continuously during multi-Segment

Split-Screen display.

9-channel DVR :

16-channel DVR:

4 Seg B 4 Seg C

4 Seg A

4 Seg B

4 Seg A

16 Seg

4 Seg D

9 Seg

4 Seg C

9 Seg B

9 Seg A

(Example) Screen display in live mode (9-channel DVR)

4-segment split A

4-segment split B

Press the

Multi-Screen key.

Press the

Multi-Screen key.

Press the

Multi-Screen key.

9-segment split

4-segment split C

Press the

Multi-Screen key.

Download from Www.Somanuals.com. All Manuals Search And Download.

8.3. Sequence Display

Camera live images are displayed in sequential order when the Sequence key is pressed while in live mode.

Viewing intervals and cameras to be displayed can be set on the menu screen. Sequence key lights

continuously during Sequence display.

(Setting Example)

Step 1

Step 2

Step 1 : Camera 1 3 seconds

Step 2 : Camera 2 3 seconds

Step 3 : Camera 3 3 seconds

3 seconds elaps

Step 4 : 4-split A

3 seconds

Note

That when the screen is switched, the

picture may be distorted momentarily.

3 seconds elaps

Step 4

Step 3

3 seconds elaps

8.4. Zoom Display

Live or recorded full-screen images can be viewed in 2 x zoom display. Zoom key lights continuously while the

Zoom selection screen or Zoom screen is displayed.

Live or play back screen

Zoom selection screen

Zoom screen

Zoom key

Menu key

Zoom key

1. Press the zoom key

The zoom selection screen is displayed. The pointer is displayed on the screen.

2. Move the central point of the subject to be zoomed using the [

press the Menu key.

], [

], and [

] keys, then

The subject can be zoomed with the designated point at the center. Zoomed areas can be moved using the

], [ ], [ ], and [ ] keys even while zoomed.

[

3. Press the Menu key when the zoom screen is displayed.

The display reverts to the zoom selection screen. Pressing the Zoom key again when the zoom screen is

displayed resets the zoom display.

Note

When channels are changed, multi-segment split-screen display is selected, or a search function is operated

during zoom display, the zoom mode is reset.

Download from Www.Somanuals.com. All Manuals Search And Download.

9. RECORDING

9.1. Priority Recording

Priority recording is given higher priority over Auto recording. Use this recording mode to check recording

details when, for example, a suspicious person intrudes or when making recording outside the scheduled time

period. In the Priority Recording settings, the following settings can be made for individual cameras: recording

ON/OFF, recording rate, picture quality and audio ON/OFF.

9.1.1. How to perform priority recording

1. Press the Priority Recording key to start the priority recording. To stop a buzzer sound, press the Buzzer

Stop key.

2. Hold down the Priority Recording key for 2 seconds or more to terminate the priority recording.

9.2. Auto Recording (Alarm Event Recording and Normal Recording)

With auto-recording, recordings are made according to a preset schedule, which can include up to twelve

different programs. If one or more programs have duplicate execution times, the program with a largest

number takes precedence. Settable items for each program include: Day of the Week; Start/End Times; and

Operation. Up to six settings groups, named A through F, can be made for "Operation," and recording settings

for Normal and Alarm recording can also be registered. Further, up to sixty "special day" operational settings

can also be made, with operation controlled by different programs, motion detection areas for individual

cameras, and audio recording during auto- recording.

9.2.1. Alarm event recording

Alarm Event recording includes both "Alarm Input" and "Motion Detection" recording. For Alarm Event

recording, settable items for each individual camera include: Recording ON/OFF; Recording Rate; and Picture

Quality. It is also possible to set, for each recording mode, the type of events that will cause recording to

begin.

For Alarm Event recording mode, it is possible to set the type of recording operation to be performed when

multiple events have occurred simultaneously. Setting the mode to "Sequence" allows two or more events to

be set for individual cameras. For Alarm Input recording time, set both alarm input mode and post alarm time

intervals. For Motion Detection, set both motion detection mode and post-motion alarm time.

When an alarm event occurs, the corresponding camera's image is switched to full-screen display until the

preset alarm time interval has elapsed, after which the display reverts to the original screen display.

Alarm input recording:

Alarm Input recording begins when signals are received at the alarm input

terminal on the rear panel. Use event settings to set cameras to be recorded. If

"Sequence" is selected, up to four alarm input terminals can be set optionally

per camera. If "Last" is selected, the "Alarm ON/OFF" can be set only for the

alarm input terminal with a number corresponding to that of the camera.

motion detected recording: Motion Detection recording begins when motion is detected in a camera image.

Use Motion Settings to set the motion detection area, sensitivity, and activation.

Use event settings to set cameras to be recorded. If "Sequence" is selected as

the alarm event recording mode, then up to four alarm input terminals can be

set optionally per camera. If "Last" is selected, the "Alarm ON/OFF" can be set

only for the alarm input terminal with a number corresponding to that of the

camera.

9.2.2. Normal recording

This function automatically records camera images set by schedule. For Normal recording, settable items for

each individual camera include: Recording ON/OFF; Recording Rate; and Picture Quality. (Refer to p. 81;

Normal Recording setting.) Recordings can be made on scheduled patterns like "day and night," and

"weekdays and holidays" by combining two or more programs.

Download from Www.Somanuals.com. All Manuals Search And Download.

10. PLAYBACK

10.1. Playback

Press the Play [

] key.

Recorded images are played back. The Playback key lights green, displaying the playback screen.

When playback is performed again, playback begins from the time at which it last stopped.

10.2. Reverse playback

Press the Reverse Play [

] key.

Plays back recorded images in reverse chronological order. The Reverse Play key lights green, displaying the

reverse playback screen.

When reverse playback is performed again, it begins from the time at which it last stopped.

10.3. Playback stop

(

)

Press the Stop [

]

key

Stops pictures being played back. Stopping the playback switches the display to the live mode.

10.4. Earliest image display

(

)

Press the Play [

] key while holding down the Playback Stop [

]

key.

Playback begins from the time at which the earliest image was recorded.

10.5. Latest image reverse playback

(

)

Press the Reverse Play [

] key while holding down the Playback Stop [

]

key.

Reverse playback begins from the time at which the latest image was recorded.

10.6. Fast forward/reverse playback

Press the Play [

]] key (Reverse Play [

] key when in reverse playback mode) during playback.

Fast forward playback (fast reverse playback when in reverse playback mode) is initiated. Playback speed

cycles through 2X, 4X and 8X whenever the key is pressed. The speed can be increased using the 1-minute

or 10-minute time skip function.

Playback speed

Normal speed

2 times (X2)

4 times (X4)

8 times (X8)

10-minute time skip (X10 minute)

1-minute time skip (X 1 minute)

Notes

• The 1-minute/10-minute skip function may not operate correctly if recordings are made with the clock turned

back.

• Recorded images may not be played back at the indicated speed depending on the hard disk access time,

etc.

• For the pre-recorded recording data, it cannot playback skips forward in 1-minute/10-minute segments.

Download from Www.Somanuals.com. All Manuals Search And Download.

10.7. Pause

1. Press the Pause [

] (

) key during forward or reverse playback.

Playback is temporarily stopped and the key lights green.

2. To perform playback again, press the Play [

] key or Reverse Play [

] key.

Pause mode is cancelled and forward or reverse playback begins again.

10.8. Frame advance/reverse playback

Press the Play [ ] key or Reverse Play [

recording is temporarily stopped ,

] key with the Pause [

] (

) key pressed, while

Frame advance or reverse playback is performed per screen whenever the key is pressed.

10.9. Instance event access

Recording moves to the event start time (Priority recording, Alarm Event recording or Normal recording) and

temporarily stops. Playback images can be moved from event to event and required images can be quickly

searched

[Instant access to the next event]

Hold down the Play [

] key for 2 seconds or more while playback is temporarily stopped.

Playback advances to the beginning of the next event and temporarily stops.

[Instant access to the previous event]

Hold down the Reverse Play [

] key for 2 seconds or more while playback is temporarily stopped.

Playback advances to the beginning of the current event and temporarily stops.

Download from Www.Somanuals.com. All Manuals Search And Download.

11. SEARCH

11.1. Date/Time Search

Entering the date and time to perform a search displays all camera images recorded closest to the designated

time in freeze-frame on the 16-segment (or 9-segment) split screen display. If no recording is made on the

designated date and time, the date and time closest after the designated date and time is displayed. The

oldest and newest times for recorded data are displayed, so please enter dates and times occurring between

these.

1. Press the Search key.

The Search screen is displayed.

D A T

M E S E A R C H

M E E B

2. Select "DATE/TIME SEARCH," press the Menu key.

Date/Time search screen is displayed.

S E A R C H

E X E C U T

R E C

T A R T

E B

R E C E N D

3. Move the cursor with the [

clock settings using the [+] and [

date, hour, minute, and second.

] and [

] keys and perform

] keys. Set year, month,

4. Move the cursor to "EXECUTE" and press the Menu key.

Images recorded at the time closest to the designated time

are displayed.

S E A R C H S C R E E N

E B

S P L A Y

M E

An error message is displayed at upper right of the screen if

images does not exist after the designated time.

Pressing the Menu key moves the cursor to the previous

position.

N O T H I N G

F O U N D

O K

Download from Www.Somanuals.com. All Manuals Search And Download.

12. ARCHIVE

The Digital Video Recorder is equipped with an archive function that transfers image data recorded on the

hard disk to DVD-R disk (available only to models with DVD drives) or USB memory. Camera image data

designated between start position and end position can be archived. Since dedicated viewer software is also

downloaded at the same time, archived images can be easily played back on a PC.

Note

Archive operation can be performed only at the operation level 1. When the security has been set, perform

archive operation after login to the Operation Level 1.

12.1. Archiving by Entering the Date and Time

Use this method for archiving when the date and time are known. Insert the DVD to be archived into the

Digital Video Recorder or connect the USB flash memory to the Digital Video Recorder;

1. Hold down the Menu key for 2 seconds or more.

Menu screen is displayed.

M A G E A R C H

N G

T A R T

P O S

E B

E N D P O S

T A R T

E N D P O S

T A R T P O S

E N D P O S

T A R T P O S

E N D P O S

P O S

2. Move the cursor with the [

] and [

] keys, select

"IMAGE ARCHIVING," and press the Menu key.

Image archive screen is displayed.

T A R T

P O S

E N D P O S

C A M E R A

E X E C U T

T R A N S

E R

3. Using the [+] and [

1 and End 1.

-] keys, enter the time and date for Start

R E C

T A R T

E B

R E C E N D

4. To continue to archive other data, repeat Step 3.

Up to 5 start and end "dates and times" can be set.

Note

A separate folder is created at the destination to be

archived each time archiving starts and ends. Perform

archiving by shifting time even when archiving for

consecutive time. Dividing folders results in fewer files in

each folder, thereby making search and display faster.

E X E C U T E ?

U S B D V D C A N C E L

USB:

DVD:

Archive to the USB memory

Archive to the DVD-R

Cancel: Reverts to the previous cursor

position without executing.

5. Move the cursor with the [

perform camera setting using the [+] and [

Select the camera to be archived from "CAMERA 1

] and [

]keys and

-] keys.

-9" and

)

(

"ALL." For 16 channels, up to camera 16 can be selected.

6. Move the cursor using the [ ] and [

"EXECUTE," and then press the Menu key.

] keys, select

A message box for selection of either USB or DVD is

displayed at the upper right of the screen. (model with DVD

drive only)

For the model without DVD drive, Selection message "Yes"

or "Cancel" is displayed.

7. Move the cursor using the [

] and [

] keys, select

"USB" or "DVD," and then press the Menu key.

For the model without DVD drive, select "YES," then press

the Menu key.

Download from Www.Somanuals.com. All Manuals Search And Download.

13. SPECIFICATIONS

* 0 dB = 1V

C-DR091

-08

C-DR091

-1

C-DR091

-3

-6

Model

110 – 120 V AC 50/60 Hz

400 mA

Power Source

410 mA

480 mA

530 mA

Power Consumption

Image Compression

Video Format

Motion-JPEG

NTSC

E-IDE Hard Disk

160 GB (160 GBx 1)

9 channels, VBS1.0 V(p-p), 75 Ω, BNC

E-IDE Hard Disk

Recording Medium

80 GB (80 GBx 1)

320 GB (160 GBx 2)

600 GB (300 GBx 2)

Video Input

9 channels, VBS1.0V(p-p), 75 Ω, BNC, loop-through

Video Output

Monitor Output

2 channels, VBS1.0V(p-p), 75 Ω, BNC,

1 channel is dedicated to real-time image (Full-screen and 4-segment split screen display

only. Nothing is displayed other than camera names and camera numbers.)

1 channel, VBS1.0V(p-p), 75 Ω, BNC, Connect the monitor output of other digital video recorder

(C-DR091/161 series) to this terminal. Multiple digital video recorders can be operated and

monitored with a single monitor by using the C-RM1000 Remote Controller (option).

8 bits, Linear PCM, sampling frequency: 16 kHz

Link Input

Audio Recording System

Audio Input

1 channel, –10 dB*, 10 kΩ, unbalanced, RCA pin jack

1 channel, –10 dB*, 600 Ω, unbalanced, RCA pin jack

Audio Output

1-, 4-, 9-, segment screen sequence, electronic 2 x zoom

Changeable in 5 steps, (File size: 16 - 64KB) 64 KB (Quality 1), 40 KB (Quality 2),

32 KB (Quality 3), 24 KB (Quality 4), 16 KB (Quality 5)

Screen Display

Picture Quality

720 x 240 pixels

Pixels

Total recording rate 120 IPS (each camera can be individually set for the following rate)

120, 60, 30, 15, 8, 4, 2, 1, 1/2, 1/3, 1/5, 1/10, 1/20, 1/30, 1/60 IPS

Max. 5 min (0 - 300 s)

Recording Rate

Pre-Recording

Post Alarm Recording

Date/Time

Max. 999 s (0 - 999 s), non-limit

Year/ month/ date/ hour/ minute/ second, 24-hours format display,

monthly deviation of within ±30 s (25°C (77°F)), can be operated until the year 2099

5 Sensitivity levels, can be turned on/off for individual areas

Motion Detect

Date/Time search, Event search (Priority recording, Alarm-input recording,

Normal recording, Motion detect recording, all)

Search Function

9 channels (EDGE, LEVEL), no-voltage make contact input, open voltage: 2 V DC,

short-circuit current: 1.5 mA, minimum short-circuit time: over 100 ms,

loop resistance: under 100 Ω, screwless connector

Alarm Input

4 channels (can be set for Priority recording, Alarm-input recording, Motion detect

recording, Video loss, HD Full, Fan Failure, and HD Error) open collector output,

withstand voltage: 30 V DC, control current : 20 mA, screwless connector

1 channel, no-voltage make contact input, open voltage: 2 V DC, short-circuit current: 1.5 mA,

minimum short-circuit time: over 100 ms, loop resistance: under 100 Ω, screwless connector

1 channel, no-voltage make contact input, open voltage: 2 V DC, short-circuit current: 1.5 mA,

minimum short-circuit time: over 100 ms, loop resistance: under 100 Ω, screwless connector

1 channel, open collector output, withstand voltage: 30 V DC,

Control Output

Priority Recording Input

Time Synchronization

Input

Time Synchronization

Output

control current: 20 mA, screwless connector

1 channel, RS-485, screwless connector

Camera Control

Remote Control

Disk Array

1 channels, RS-485, screwless connector or RJ11

2 channels, eSATA (and dedicated control signal), eSATA connector and modular connector

RS-232C : D-sub connector (9 pin, male), 10 BASE-T/100 BASE-TX ethernet : RJ45

mail transmission capability, USB terminals (ARCHIVE, KEY LOCK), Web function (Real-

time image, play-back, remote, menu), Language choice (English/ French/ Japanese)

Under 3,000 m (9,843 ft) (relative to sea level)

Communication Function

Other Function

Altitude

+5°C to +40°C (41°F to 104°F) (+5°C to +35°C (41°F to 95°F) when mounted on a rack)

Under 80% RH (no condensation)

Operating Temperature

Operating Humidity

Finish

Panel: Surface-treated steel plate, black, paint, 30% gloss

Case: Pre-coated steel plate, black

420 (W) x 93.9 (H) x 332.8 (D) mm (16.5 (W) x 3.7 (H) x 13.1 (D) inch)

Dimensions

Weight

5.7 kg (12.6 lb)

6.5 kg (14.3 lb)

Power supply cord (2 m (6.6 ft)) … 1

Rack mounting bracket: MB-23B

Accessory

Option

Note: The design and specifications are subject to change without notice for improvement.

Download from Www.Somanuals.com. All Manuals Search And Download.

* 0 dB = 1V

C-DR161

-08

C-DR161

-1

C-DR161

-3

-6

Model

110 – 120 V AC 50/60 Hz

430 mA

Power Source

440 mA

540 mA

560 mA

Power Consumption

Image Compression

Video Format

Motion-JPEG

NTSC

E-IDE Hard Disk

160 GB (160 GBx 1)

16 channels, VBS1.0 V(p-p), 75 Ω, BNC

E-IDE Hard Disk

Recording Medium

80 GB (80 GBx 1)

320 GB (160 GBx 2)

600 GB (300 GBx 2)

Video Input

16 channels, VBS1.0V(p-p), 75 Ω, BNC, loop-through

Video Output

Monitor Output

2 channels, VBS1.0V(p-p), 75 Ω, BNC,

1 channel is dedicated to real-time image (Full-screen and 4-segment split screen display

only. Nothing is displayed other than camera names and camera numbers.)

1 channel, VBS1.0V(p-p), 75Ω, BNC, Connect the monitor output of other digital video recorder

(C-DR091/161 series) to this terminal. Multiple digital video recorders can be operated and

monitored with a single monitor by using the C-RM1000 Remote Controller (option).

8 bits, Linear PCM, sampling frequency: 16 kHz

Link Input

Audio Recording System

Audio Input

1 channel, –10 dB*, 10 kΩ, unbalanced, RCA pin jack

1 channel, –10 dB*, 600 Ω, unbalanced, RCA pin jack

Audio Output

1-, 4-, 9-, 16-, segment screen sequence, electronic 2 x zoom

Changeable in 5 steps, (File size: 16 - 64KB) 64 KB (Quality 1), 40 KB (Quality 2),

32 KB (Quality 3), 24 KB (Quality 4), 16 KB (Quality 5)

Screen Display

Picture Quality

720 x 240 pixels

Pixels

Total recording rate 120 IPS (each camera can be individually set for the following rate)

120, 60, 30, 15, 8, 4, 2, 1, 1/2, 1/3, 1/5, 1/10, 1/20, 1/30, 1/60 IPS

Max. 5 min (0 - 300 s)

Recording Rate

Pre-Recording

Post Alarm Recording

Date/Time

Max. 999 s (0 - 999 s), non-limit

Year/ month/ date/ hour/ minute/ second, 24-hours format display,

monthly deviation of within ±30 s (25°C (77°F)), can be operated until the year 2099

5 Sensitivity levels, can be turned on/off for individual areas

Motion Detect

Date/Time search, Event search (Priority recording, Alarm-input recording,

Normal recording, Motion detect recording, all)

Search Function

16 channels (EDGE, LEVEL), no-voltage make contact input, open voltage: 2 V DC,

short-circuit current: 1.5 mA, minimum short-circuit time: over 100 ms,

loop resistance: under 100 Ω, screwless connector

Alarm Input

4 channels (can be set for Priority recording, Alarm-input recording, Motion detect recording

Video loss, HD Full, Fan Failure, and HD Error) open collector output,

withstand voltage: 30 V DC, control current : 20 mA, screwless connector

1 channel, no-voltage make contact input, open voltage: 2 V DC, short-circuit current: 1.5 mA,

minimum short-circuit time: over 100 ms, loop resistance: under 100 Ω, screwless connector

1 channel, no-voltage make contact input, open voltage: 2 V DC, short-circuit current: 1.5 mA,

minimum short-circuit time: over 100 ms, loop resistance: under 100 Ω, screwless connector

1 channel, open collector output, withstand voltage: 30 V DC,

Control Output

Priority Recording Input

Time Synchronization

Input

Time Synchronization

Output

control current: 20 mA, screwless connector

1 channel, RS-485, screwless connector

Camera Control

Remote Control

Disk Array

1 channels, RS-485, screwless connector or RJ11

2 channels, eSATA (and dedicated control signal), eSATA connector and modular connector

RS-232C : D-sub connector (9 pin, male), 10 BASE-T/100 BASE-TX ethernet : RJ45

mail transmission capability, USB terminals (ARCHIVE, KEY LOCK), Web function (Real-

time image, play-back, remote, menu), Language choice (English/ French/ Japanese)

Under 3,000 m (9,843 ft) (relative to sea level)

Communication Function

Other Function

Altitude

+5°C to +40°C (41°F to 104°F) (+5°C to +35°C (41°F to 95°F) when mounted on a rack)

Under 80% RH (no condensation)

Operating Temperature

Operating Humidity

Finish

Panel: Surface-treated steel plate, black, paint, 30% gloss

Case: Pre-coated steel plate, black

420 (W) x 93.9 (H) x 332.8 (D) mm (16.5 (W) x 3.7 (H) x 13.1 (D) inch)

Dimensions

Weight

5.8 kg (12.8 lb)

6.6 kg (14.6 lb)

Power supply cord (2 m (6.6 ft)) … 1

Rack mounting bracket: MB-23B

Accessory

Option

Note: The design and specifications are subject to change without notice for improvement.

Download from Www.Somanuals.com. All Manuals Search And Download.

* 0 dB = 1V

C-DR091D6

C-DR091D08

110 – 120 V AC 50/60 Hz

490 mA

C-DR091D1

500 mA

C-DR091D3

570 mA

Model

Power Source

590 mA

Power Consumption

Image Compression

Video Format

Motion-JPEG

NTSC

E-IDE Hard Disk

Recording Medium

80 GB (80 GBx 1)

160 GB (160 GBx 1)

320 GB (160 GBx 2)

600 GB (300 GBx 2)

9 channels, VBS1.0 V(p-p), 75 Ω, BNC

Video Input

9 channels, VBS1.0V(p-p), 75 Ω, BNC, loop-through

Video Output

Monitor Output

2 channels, VBS1.0V(p-p), 75 Ω, BNC,

1 channel is dedicated to real-time image (Full-screen and 4-segment split screen display

only. Nothing is displayed other than camera names and camera numbers.)

1 channel, VBS1.0V(p-p), 75 Ω, BNC, Connect the monitor output of other digital video

recorder (C-DR091/161 series) to this terminal. Multiple digital video recorders can be operated

and monitored with a single monitor by using the C-RM1000 Remote Controller (option).