F O O D S E R V I C E
Use and Care Manual
Read And Save These Instructions
®
®
®
High-Performance Commercial Blenders
Includes: BarBoss • Drink Machine
(Two-Step Timer, Two-Speed, Variable Speed)
Vita-Prep 3 • Vita-Prep • Vita-Pro
All Models
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Vita-Mix® blenders come with several different control options. Please be sure
you are following the instructions for your blender model.
Variable Speed Model
(Drink Machine, Vita-Prep, Vita-Prep 3, Vita-Pro)
Timer & Pulse Model
ON/OFF Power Switch. Up for ON. Down for OFF.
(BarBoss®)
HIGH/VARIABLE Switch. HIGH overrides the
VARIABLE SPEED dial and is the fastest speed
available. Switch must be set to VARIABLE to use
the VARIABLE SPEED dial.
ON/OFF Power Switch. Located on the front of the
machine below the control panel, the ON/OFF switch
controls the power to the machine. While plugged in,
switch to ON to ready the machine for blending.
Shut OFF the power switch at night or whenever the
machine will be left unattended.
VARIABLE SPEED Dial. Allows user to select con-
tinuously variable motor speeds ranging
from 1,000 rpm to 24,000 rpm. Active only
when HIGH/VARIABLE switch is set on
VARIABLE position.
TIMER Dial. Allows user to select a number of
timed settings. All times are total times. Increments
on timer are approximate seconds. Timer is activated
only when the power switch is ON. Blender will
shut off automatically at the end of the pre-set time.
Two-Speed Model
(Drink Machine)
START/STOP TIMER Switch. This is a lighted
switch. When light is lit, power is ON. Depress
START/STOP TIMER switch to activate timer
setting and again to stop a blending cycle.
ON/OFF Power Switch. Up for ON. Down for OFF.
HIGH/LOW Switch. Up for HIGH. Down for LOW.
During operation, you may interrupt timer by
pressing the START/STOP switch.
Note on Timers: Stop mid-cycle with
the START/STOP switch, not the
ON/OFF switch. If the ON/OFF
switch was used, wait 30 seconds for
power to recycle and the timer to
reset before resuming operation.
NOTE: Switches may become sticky from use. Unplug the machine and use a wet
cloth, moistened with water and a mild detergent, to clean around the edges of the
switch paddles until they function freely. Work the switches back and forth a few times
to loosen any dried residue under switch. Leaving switches sticky will damage or burn
out the switches. Clean carefully, using caution not to allow water or other liquids to
infiltrate the switch. Dry with a soft cotton cloth.
PULSE Switch. The PULSE switch can be used to
quickly refresh product in the container by depressing
the switch and holding down as long as needed.
The Pulse switch can only be used when the power
switch is ON.
Two-Step Timer Model
(Drink Machine)
ON/OFF Power Switch. Up for ON. Down for OFF.
TIMER Dial. Allows user to select a number of
timed settings. All times are total times. Increments
on timer are approximate seconds. Timer is activated
only when the power switch is ON. Blender will
shut off automatically at the end of the pre-set time.
Note on Two-Step Timers: Stop mid-
cycle with the START/STOP switch,
not the ON/OFF switch. If the ON/OFF
switch was used, wait 30 seconds for
power to recycle and the timer to
reset before resuming operation.
START/STOP TIMER Switch. This is a lighted
switch. When light is lit, power is ON. Depress
START/STOP TIMER switch to activate timer
setting and again to stop a blending cycle.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Two-Piece Lid
Compact 32 oz. / 0.9 Ltr. Polycarbonate/
Stackable Container
Lock
Unlock
The two-piece lid is easy to clean and easy
to put on, take off and seal.
• The lid has a continuous rim which fits tightly
inside the container. Push lid into container
until the side latches are snapped under the
container lip.
NOTE: Vita-Mix® lids come in several different styles. Please be sure you are following
the instructions for your style of lid.
Figure D
Two-Piece Lid
64 oz. / 2.0 Ltr. Polycarbonate Container
Unlock
Top view of lid showing Locking Icons.
Lock
The two-piece lid is easy to clean and easy
to put on and take off.
Position
Indicator Tab
• To remove lid, pull up gently on the side lid
latches.
Press in above
container tab
to remove lid
• The lid has a continuous rim which latches
inside the container tabs. Push one side of
the rim under one tab, and with the heel of
• To secure lid plug: Position the lid plug over
the lid and align either of the position indicator
tabs with one of the unlocked icons. Press
the plug into the lid and turn until an indicator
tab is aligned with a locked icon. (Turn the lid
over to be sure that plug is properly locked –
the locking feet must be seated into the lid
locking notches.) The bottom surface of the
plug should be snug against the top of the lid.
• The lid plug can be removed when using the
accelerator tool or adding ingredients. Turn
plug to an unlocked icon to remove.
Figure A
Rim
your hands push down, over the opposite tab,
Top view of lid showing Locking Icons.
to snap lid into position.
• To remove lid, place hands around the lid,
pressing thumbs above one of the container
tabs. Push in and lift off.
Press in above
container tab
to remove lid
Position
Indicator Tab
Side lid
latches
• To secure lid plug: Position the lid plug over
the lid and align either of the position indicator
tabs with an unlocked icon. Press the plug into
the lid and turn until an indicator tab is aligned
with one of the locked icons. (Turn the lid over
to be sure that plug is properly locked – the
locking feet must be seated into the lid locking
notches.) The bottom surface of the plug
should be snug against the top of the lid.
• The lid plug can be removed when using the
accelerator tool or adding ingredients. Turn
plug to an unlocked icon to remove.
Rim
Figure E
Always lock lid when processing hot
liquids. See warning on page 3.
Container
Tab
Two-Piece Lid
48 oz. / 1.4 Ltr. Polycarbonate/Stackable
Container
The two-piece lid is easy to clean and easy to put
on, take off and seal.
Figure B
Always lock lid when processing hot
liquids. See warning on page 3.
• Push lid into container until the side latches are
snapped under container lip. (See F(1) - F(3).)
• To remove fully latched lid, squeeze tabs
together on both sides of the container, pull
upward and off.
One-Piece Lid (Optional)
64 oz. / 2.0 Ltr. Polycarbonate Container
The one-piece lid is easy to put on or take off,
and to clean, for quick operation.
Figure F
• The lid plug can be removed when using the
accelerator tool. Twist plug to fasten or remove.
• There is no latch on this lid. Simply hold the
lid on when starting.
• Add ingredients through port in top.
F(1) Unsealed/Unlatched
F(2) Sealed
F(3) Fully Latched
CAUTION: Do not use non-latching one-piece lid
when processing hot ingredients. Not for use with
an accelerator tool.
Figure C
NOTE: Brand new lids may be a little stiff. This is temporary. To make new lids easier
to insert and remove, rub a light coating of cooking oil around rim where it seals. Place
it in container for several minutes, remove and lightly wipe oil off lid.
Lid resting on container
using hand to stabilize.
Lid pushed into container.
Side latches are not under
container lip.
Side latches are snapped
under container lip.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Plug the machine into the nearest outlet (if unplugged). Press ON/OFF switch to ON.
Activate the timer by selecting the desired timer setting on the dial and then depressing
the START/STOP TIMER switch on the left.
Two-Speed or Variable Speed Drink Machines,
®
®
®
Vita-Pro, Vita-Prep and Vita-Prep 3
4a. If mixture stops circulating, you have likely trapped an air bubble. Either insert the
accelerator tool through the lid while blending (see page 11), or stop the motor,
remove the container from the base and stir or scrape the mixture from the sides
of container into the center using a rubber spatula to press any air bubbles away
from the blades. Replace the lid and continue blending.
1. Place liquids and soft foods in container first, solid items and ice last. Although not
necessary for processing, you may want to cut or break food into smaller pieces for
precise measuring of ingredients. Thawed or partially thawed fruit is recommended.
High-speed is recommended for heavy-duty blending.
2. Set the container on the motor base by aligning it over the centering pad anchored to
the base. (Motor must be completely stopped before positioning container.)
Containers are not to be used for hard, dry materials. Avoid running the blender with
the container empty.
4b. Due to the blending speed of the machine, processing times are greatly reduced
over other manufacturers’ machines. Until you become accustomed to the speed,
watch your mixture carefully to avoid over-blending.
4c. If stopping the machine mid-cycle, use the START/STOP switch, not the ON/OFF
switch. If the ON/OFF switch was used, wait 30 seconds for power to recycle and
the timer to reset before resuming operation.
3. Always use a lid when blending. If blending hot ingredients, the lid must be securely locked
in place. When processing hot liquids, DO NOT use a non-latching or one-piece lid.
4. Plug the machine into the nearest outlet (if unplugged). Select desired speed setting.
Most foods are blended on HIGH speed. Start heavy or thick foods on the recommended
speed then switch to HIGH once the mixture begins processing.
Note: The START/STOP TIMER switch on your machine is lit when power is ON.
Avoid moveable parts. The machine may stop working if it is overloaded on low
speed. Reset the machine by turning power off for 30 seconds.
Warning: If you detect a change in the sound of the machine or if a hard or
foreign object comes into contact with the blades, do not serve the drink.
Inspect your blade assembly for loose, nicked or missing parts. If parts are
loose, missing, or nicked, replace with new blade assembly. (See page 10.)
5. After the blender has been stopped, wait until the blade comes to a complete stop before
removing the lid or container from the motor base.
4a. If mixture stops circulating, you have likely trapped an air bubble. Either insert the
accelerator tool through the lid while blending (see page 11), or stop the motor,
remove the container from the base and stir or scrape the mixture from the sides
of container into the center using a rubber spatula to press any air bubbles away
from the blades. Replace the lid and continue blending.
4b. Due to the blending speed of the machine, processing times are greatly reduced
over other manufacturers’ machines. Until you become accustomed to the speed,
watch your mixture carefully to avoid over-blending.
6. To use the PULSE switch to refresh drinks: Make sure the power is ON. With the
container on the motor base, depress the PULSE switch. Release the switch to stop
the motor.
Warning: If you detect a change in the sound of the machine or if a hard or
foreign object comes into contact with the blades, do not serve the drink/food.
Inspect your blade assembly for loose, nicked or missing parts. If parts are
loose, missing or nicked, replace with new blade assembly. (See page 10.)
6. After the blender has been stopped, wait until the blade comes to a complete stop before
removing the lid or container from the motor base.
7. Press the ON/OFF switch to OFF when not in use.
NOTE: The thermal protector may shut the motor off to protect it from overheating. To
restart, wait for motor to cool down with the power off (up to 45 minutes). Cooling may be
quickened by placing the motor base in a cool spot. Unplug first. To speed up the process,
try circulating the air with a vacuum or fan aimed at the bottom of the base. When the thermal
protector shuts the motor off, review your processing techniques and your instructions.
Your recipes may be too thick (add liquid), be processed too long at too low a speed setting,
or have too much material in them. If the motor seems to be overheating but the thermal
protector has not turned the machine off, stop the machine and remove the container
from the base.
®
Bar Boss and Timer Blender Instructions
1. Place liquids and soft foods in container first, solid items and ice last. Although not
necessary for processing, you may want to cut or break food into smaller pieces for
precise measuring of ingredients. Thawed or partially thawed fruit is recommended.
High-speed is recommended for heavy-duty blending.
2. Set the container on the motor base by aligning it over the centering pad anchored to
the base. (Motor must be completely stopped before positioning container.)
Containers are not to be used for hard, dry materials. Avoid running the blender with
the container empty.
Follow these instructions for the Two-Speed or Variable Speed Drink Machines, Vita-Pro
and Vita-Preps: Set the dial on HIGH (#10). Turn the machine ON and let the machine run
for 1 minute. Be careful never to touch any moving part while in use.
Follow these instructions for the BarBoss and Timer Blenders: Set the timer for 20
seconds. Turn the machine ON and let the machine run for 20 seconds. Repeat this step 3
times for a total of 1 minute. Be careful never to touch any moving parts while in use.
3. Always use a lid when blending. If blending hot ingredients, the lid must be securely locked
in place. When processing hot liquids, DO NOT use a non-latching or one-piece lid.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Assembly
AcceleratorTool/MotorBase
Blade Agitator Assembly. The blade assembly
includes a precision-hardened stainless steel blade
with enclosed steel ball bearings for maximum durability.
The accelerator tool prevents an air bubble
Splash
from forming while blending and allows for
Disk
Step
the processing of very thick and/or difficult-
to-process frozen mixtures. While the
machine is running, use the accelerator
tool to push ingredients into the blades.
General Instructions
The rugged blade assembly literally explodes molecules
of food and ice in the container, helping every batch to
homogenize more effectively. The blade does not
need to be removed for normal cleaning. (Refer to the
information below to remove or replace.)
Accelerator Tool use:
• If thick mixtures stop circulating, you
may have trapped an air bubble. Insert
the accelerator tool through the lid and
stir to release it.
• Use it only with the lid locked in place
and lid plug removed.
Service Contract
Drive Spline. Mates with drive socket on the motor
base to turn the blade. NOTE: Removing and replacing
your container while the coupling is still rotating
will strip the drive spline “teeth.” (This part is
NOT removable.)
NOTE: The accelerator tool has a small
“step” on it to prevent contact with the
blades Do not push the accelerator tool “step”
past the lip of the 32 oz. / 0.9 Ltr. compact
container. The accelerator tool cannot be
used with a one-piece non-latching lid.
• The splash disk (near the top of the
accelerator tool) and lid prevent the
accelerator tool from hitting the blades.
• The container should not be more than
2/3 full when the accelerator tool is used.
• Do not use the accelerator tool for
more than 30 consecutive seconds (to
avoid overheating).
Retainer Nut. Must be snug. Order the available
Retainer Nut Wrench for best results. (Refer to the
information below to remove or replace.)
DO NOT force the accelerator tool
into the 32 oz. / 0.9 Ltr. container.
Excessive force may cause the
Never use a blade assembly with loose, damaged or nicked components.
• Holding the accelerator tool straight
should allow extra thick ingredients to
circulate. If not, point the accelerator
tool toward the side or corner of the
container.
accelerator tool to extend too far into the
container and may cause damage to the
blades. DO NOT use the older accelerator
tool that has a straight and smooth surface
and no “step.” Use of the older model may
cause damage to the blades.
Blade Assembly Removal
CAUTION: Do not remove blades unless absolutely necessary!
At times, it may be necessary to give your blades additional
cleaning. An easy-to-use blade assembly removal wrench
(Item #15596) may be purchased through your Vita-Mix
Distributor. Never attempt to take the blade assembly itself
apart. This will void the warranty.
Turn the container upside down and grip firmly. Insert retainer
nut wrench in groove of retainer nut and rotate counterclockwise
to loosen. Then grip blades with a cloth and remove retainer
nut by hand.
When processing hot liquids:
• The two-part latching lid must be securely locked in place. This allows steam
to escape naturally and will prevent the lid from coming off when the machine
is turned on.
• Do not start processing hot liquids on HIGH speed. Always start processing hot
liquids on LOW speed, then switch to HIGH speed while the machine is running.
• Use caution with hot liquids. Liquids may spray from under the lid plug
or escaping steam may cause scalding.
Retainer Nut Wh
• Do not process hot ingredients with the Vita-Mix non-latching lid.
Replacing Blade Assembly
With the container upside down, grip blades with cloth, insert
into the container bottom and align with flat sides of container
opening. Place retainer nut on and hand tighten. Last, carefully
turn clockwise until secure, using wrench. Do not force. If it is
not tight enough, you will notice increased container noise.
Front
Motor Base
Power Cord. Your machine is equipped with a 6 ft. / 1.8 m power
cord. Store the unused portion neatly underneath. Plastic cord
retainer clips hold the cord securely. They are flexible and will
return to position after the cord is lifted out. There is no need to
unscrew the cord retainer clips to let out more cord.
Retainer Nut Wrench
in use.
Back
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor Base/Control Panel
1. Unplug the power cord.
2. Gently wash the outside surface with a damp soft cotton cloth moistened with a mild
solution of warm water and nonabrasive detergent or nonabrasive liquid spray
cleaner. NEVER IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID.
3. Thoroughly clean switches so that they work freely. They may become sticky. Use a
wet cloth, moistened with water* and a mild detergent, to clean around the edges of
the switch paddles until they function freely. Work the switches back and forth a few
times to loosen any dried residue under switch. Leaving switches sticky will damage
or burn out the switches. Clean carefully, using caution not to allow water or other
liquids to infiltrate the switch.
Care Note
To ensure that you get the longest possible life from your Vita-Mix machine, we
recommend the following products, when used as directed by the supplier:
CLEANING PRODUCTS. . . . . . . . . . . . . . . . . . . . . . . . . SUPPLIER
Solid Supra, Solid Power,.. . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN
Guardian Acclaim, Solid Guardian Plus, . . . . . . . . . . . . . 800-352-5326
Diverpak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI
Eclipse H2, Liqui-Safe L7 . . . . . . . . . . . . . . . . . . . . . . . . 800-521-8140
Acclean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Klenzade Products
Poly-Brite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Division of Ecolab
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . St. Paul, MN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 612-293-2165
Glow MB-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wesmar Company, Inc.
Lustre NC-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seattle, WA
Lustre Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206-783-5344
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.wesmar.com
PSRA 41-D, PSRA 41-E . . . . . . . . . . . . . . . . . . . . . . . . . Anderson Chemical Co.
Liqui-Ware 1, Liqui-Ware MC . . . . . . . . . . . . . . . . . . . . . Litchfield, MN
D-Flex, Sur-Met . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800-366-2477
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.andersonchemical.com
RINSE AIDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SUPPLIER
Solid Rinse Dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN
Solid Brilliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800-352-5326
DESTAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SUPPLIER
NuWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800-521-8140
4. Dry with a soft cotton cloth.
* Be sure to wring excess water out of cloth or sponge when cleaning around the
controls or any electrical part.
Lid
Separate the lid and plug. Wash in warm soapy water. Rinse clean under running
water and dry. Reassemble before use. (See page 6-7.)
Container
For maximum container life, do not wash in dishwasher.
1. To Clean: Fill container 1/4 full with warm (110˚F/43˚C) water and add a couple
drops of liquid dishwashing detergent.** Return container to motor base and firmly
position the two-piece lid. Run machine for 30 seconds. Empty container. Repeat
this step.
2. To Rinse: Fill container 3/4 full with warm (110˚F/43˚C) water – do not add soap.
Return container to motor base and firmly position the two-piece lid. Run machine
for 30 seconds. Empty container.
3. If any solid residue remains, remove the blade assembly (see page 10) and wash all
container parts in warm soapy water. Rinse and drain. Reassemble before next
step. Do not soak the blade agitator assembly.
NOTE: Do not use abrasive cleaning agents or concentrated bleach when cleaning.
Do not use any cleaners containing Quatinary Sanitizers on polycarbonate components
(i.e., containers). Do not use any of the following cleaning products: automatic
dishwashing detergents, oven cleaners, steel wool or other abrasive pads.
ADDITIONAL NOTE: Do not let mixtures, liquids and food products dry in the
container. Rinse throughout use. Dry product may lock around the blade and
weaken/tear the bearings seal when restarted. Do not place containers in the freezer.
Extremely low temperature combined with hot ingredients and/or the immediate rapid
action of the blade may crack the container. Due to the nature of polycarbonates,
microwaving and automatic dishwashing are not recommended. Follow the cleaning
instructions on page 13.
4. To Sanitize: If all solid residue is gone after step 2 or after completion of step 3,
fill container 3/4 full with a sanitizing solution mix.*** Return container to motor base
and firmly position the two-piece lid. Run machine on a high speed for 30 seconds.
Turn machine off and allow mixture to stand in the container for an additional 1-1/2
minutes. Pour out bleach mixture.
5. Return container to motor base and run machine empty for an additional 5 seconds.
Do not rinse after sanitizing. Allow container to air dry.
** To prolong polycarbonate container life, Vita-Mix recommends using soaps with a
low Ph balance, such as a liquid dishwashing detergent (Ivory Liquid®). Due to the
nature of polycarbonates, automatic dishwashing is not recommended.
*** Recommended sanitizing solution: 1.5 tsp. / 7.4 ml institutional or household bleach
in 2 qt. / 2.0 Ltr. water.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
®
®
®
BarBoss and Drink Machines
Vita-Pro and Vita-Prep
NOTE: Vita-Mix blenders come in several similar styles. Please be sure you are following
NOTE: Vita-Mix® blenders come in several similar styles. Please be sure you are
following the parts list for your blender model.
Item # Part
the parts list for your blender model.
Item # Part
755
1192
1191
756
Lid plug for 64 oz. / 2.0 Ltr. polycarbonate container
Lid only (no plug) for 64 oz. / 2.0 Ltr. polycarbonate container
Lid assembly for 64 oz. / 2.0 Ltr. polycarbonate container
64 oz. / 2.0 Ltr. polycarbonate container, ice blade & lid assemblies
64 oz. / 2.0 Ltr. polycarbonate container only
Lid plug for 48 oz. / 1.4 Ltr. polycarbonate/stackable container
Lid only (no plug) for 48 oz. / 1.4 Ltr. polycarbonate/stackable container
Lid assembly for 48 oz. / 1.4 Ltr. polycarbonate/stackable container
48 oz. / 1.4 Ltr. polycarbonate/stackable container,
ice blade & lid assemblies
755
1192
1191
1195
758
1159
15526
15507
15504
Lid plug for 64 oz. / 2.0 Ltr. polycarbonate container
Lid only (no plug) for 64 oz. / 2.0 Ltr. polycarbonate container
Lid assembly for 64 oz. / 2.0 Ltr. polycarbonate container
64 oz. / 2.0 Ltr. polycarbonate container, wet blade & lid assemblies
64 oz. / 2.0 Ltr. polycarbonate container only
Lid plug for 48 oz. / 1.4 Ltr. polycarbonate/stackable container
Lid only (no plug) for 48 oz. / 1.4 Ltr. polycarbonate/stackable container
Lid assembly for 48 oz. / 1.4 Ltr. polycarbonate/stackable container
48 oz. / 1.4 Ltr. polycarbonate/stackable container,
wet blade & lid assemblies
758
1159
15526
15507
15506
15502
1151
836
48 oz. / 1.4 Ltr. polycarbonate/stackable container only
Blade agitator assembly (ice blade)
Heavy-duty retainer nut
15502
1152
836
48 oz. / 1.4 Ltr. polycarbonate/stackable container only
Blade agitator assembly (wet blade)
Heavy-duty retainer nut
791
891
Sound-reducing centering pad
Drive socket
791
891
Sound-reducing centering pad
Drive socket
PLS207
760
PLS112
XDM034
Variable speed control knob / timer control knob
Accelerator Tool
Rubber Feet
PLS207
760
PLS112
XDM034
Variable speed control knob / timer control knob
Accelerator Tool
Rubber Feet
Use and Care manual (not shown)
Use and Care manual (not shown)
NOTE: Other than the drive socket, blade assembly and retainer nut, this unit is not
user serviceable.
NOTE: Other than the drive socket, blade assembly and retainer nut, this unit is not
user serviceable.
#1159
#1159
Items Sold Separately:
Items Sold Separately:
#755
#755
#1191
#756
#1191
#1195
#15507
#15506
#15507
#15504
#1192
#1192
#15526
#15502
#15526
#15502
#15596 - Retainer Nut Wrench
#15596 - Retainer Nut Wrench
#758
#758
#1151
#1152
PLS145 - One-Piece Lid
#15649
PLS145 - One-Piece Lid
#15649
#836
#791
#891
#836
#791
#891
#15647
#15640
#15647
#15652
#15648
#15643
#15648
#15643
#760
#760
#PLS207
#PLS112
#PLS207
#PLS112
32 oz. / 0.9 Ltr. Container
32 oz. / 0.9 Ltr. Container
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Problem:
• Increased vibration
Solution #1:
Dimensions:
Check blade assembly for loose, damaged
or nicked components and replace.
Solution #2:
• Leaking from bottom of container
• Increased container noise
Tighten retainer nut with retainer nut wrench
moving clockwise until it is snug. See page 10.
2. Problem:
• Machine will not run
Solution #1:
Double-check to make sure power cord is
firmly in power outlet.
Solution #2:
Check to make sure switches are clean
and moving freely.
Solution #3:
The thermal protector may have shut the
machine off. Turn power off for up to 45
minutes to reset. Note: Cooling may be
quickened by placing the motor base in a
cool spot. (Unplug first.) Try circulating the
air with a fan or vacuum aimed at the
bottom of the motor base.
64 oz. / 2.0 Ltr.
Overall Dimensions of 64 oz. / 2.0 Ltr. Polycarbonate Container with lid and base:
20 in. / 51 cm High x 8 in. / 20.3 cm Deep x 9 in. / 22.9 cm Deep
Overall Dimensions of 48 oz. / 1.4 Ltr. Polycarbonate Container with lid and base:
17.5 in. / 44 cm High x 8 in. / 20.3 cm Wide x 9 in. / 22.9 cm Deep
Ship weight of machine: 13 lbs. / 5.9 kg
3. Problem:
Solution:
• Loud noise from blade area
• Blades don’t spin
Drive Socket may be broken. Check for a
fine crack down the center or worn teeth –
replace with a new drive socket (Item
#891). Instructions are included with part.
Power Requirements:
Volts: 120 VAC
Amps: 11.5 (2+ peak hp*)
12.5 (3+ peak hp*)
Hz: 50/60
Volts: 220-240 VAC
Watts: 750-850 (2+ peak hp*)
Watts: 1100-1200 (3+ peak hp*)
Hz: 50/60
4. Problem:
Solution:
• BarBoss Pulse/Timer Blender will
not run when START/STOP TIMER
switch is activated
Check ON/OFF power switch to make
sure the switch is in the ON position.
Note: START/STOP TIMER switch is lit
when power is on.
Volts: 100 VAC (Japan)
Watts: 900 (2+ peak hp*)
Watts: 975 (3+ peak hp*)
Hz: 50/60
Volts: 120 VAC EMC (Taiwan)
Amps: 11.5 (2+ peak hp*)
Hz: 60
Cooling the motor:
Machine may stop working if it is overloaded on low speed. Reset by turning power
off for 30 seconds. Do not turn power off midway through a blending cycle. To interrupt
cycle, press START/STOP TIMER switch one time. See page 4.
*varies with voltage
If you cannot fix your machine with these suggestions, technical help is available by
calling 800-4DRINK4 (800-437-4654) or 440-235-0214. If outside the United States and
Canada, contact your local Vita-Mix Distributor or telephone the Vita-Mix International
Division at +1.440.782.2450 or email international@vitamix.com for a distributor in
your country.
16
17
PLEASE NOTE: The Service Contract outlined in the following paragraphs applies
only to customers in the United States and Canada. Customers in all other countries
should contact their local Vita-Mix® Distributor for service details.
Limited Warranty
Vita-Mix® Corporation warrants your Commercial Vita-Mix machine to be free from
defects in materials and workmanship for a period of three years from the date of
purchase when used in accordance with the accompanying instruction booklet.
This Vita-Mix machine includes a 1-Year Service Contract effective from date of
purchase. In the event your machine should need parts or repairs covered under this
Service Contract, call Vita-Mix Customer Service immediately for instructions. Proof of
date of purchase may be required. This does not cover abuse, misuse, tampering,
improper installation or extreme conditions.
Provisions of this limited warranty are void if your Vita-Mix machine has been
subjected to obvious abuse, negligence, accident, alteration, or failure to follow
operating instructions, or product exposure to abnormal or extreme conditions.
Cosmetic changes such as discoloration of parts of the product in the hands of the
user or the effects of the use of abrasive cleaners will not be warranted or considered
defects. The cleaning or removal of food products along with any damage caused by
allowing them to build up is not covered by this limited warranty. Warranty is void if
the Vita-Mix machine is put into a sound reduction chamber that does not allow proper
cooling.
The Vita-Mix Service Contract includes the following:
1. One extra drive socket – to facilitate simple repairs and prevent down time – is
included and packaged with each machine.
2. Additional drivers and accelerator tool, unless defective, are not covered. NOTE:
to determine if you have a defective part, please order a replacement part through
Vita-Mix Customer Service and, when the new part arrives, return the old part in the
same packaging. Vita-Mix will inspect the returned part and, if defective, issue a
refund for the price of the new part. A part will be considered defective if no abuse
or neglect was involved with its break. Non-defective parts sent to Vita-Mix for
inspection will not be returned if deemed unusable. Service Contract covers
functionality of the machine but not abuse or lack of recommended maintenance.
In the event your Vita-Mix machine needs service or repair covered by the terms of this
warranty, please call the Vita-Mix Corporation for shipping instructions. The Vita-Mix
machine must be sent in original or sufficient packaging.
This limited warranty is in lieu of any other warranty expressed or implied. No
representative or any other person is authorized to make any other warranty or to
assume any liability not strictly in accordance with the foregoing. This limited warranty
gives you specific legal rights which may vary from state to state. Proof of purchase
may be required to prove date of purchase.
3. In the Continental United States, sender pays freight one way to Vita-Mix
Corporation. The Vita-Mix Corporation will pay UPS ground freight charges to
return the machine to the sender. Sender pays costs for special shipping requests.
Outside the Continental United States, other service contracts may apply.
Outside the United States and Canada, other warranties may apply. Call or check
with your Vita-Mix Distributor for details or telephone the Vita-Mix International Division
at +1.440.782.2450 or email [email protected].
In case of shipping damage, notify the shipper or carrier immediately. Outside the
United States and Canada, contact your local Vita-Mix Distributor.
Before returning this product for any reason, including repair, please first contact
our Customer Service Department. In the US and Canada, call 800-4DRINK4
(800-437-4654) or 440-235-0214 to receive a “RETURN AUTHORIZATION”
NUMBER. Any return without a “Return Authorization” Number will not be
processed and will be returned to sender. Outside the United States, contact
your local Vita-Mix Distributor.
NOTE: Within the United States, Limited Warranty and Service Contract are honored
directly through the Vita-Mix Corporation, Cleveland, Ohio USA. Non-warranty repairs
can be performed by any CFESA service center. For machines sold in the United
States, call Vita-Mix: 800-4DRINK4 (800-437-4654) or 440-235-0214. If you live outside
the United States or Canada, contact your local Vita-Mix Distributor, or telephone the
Vita-Mix International Division at +1.440.782.2450 or email [email protected]
for a distributor in your country.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Additional Vita-Mix Accessories Available!
To rinse containers
quickly between
servings, the
To scrub tough
ingredients, use the
new Vita-Mix Container
Brush. Soft, flexible
fibers scrub in seconds
but won’t scratch!
Item #15639
Vita-Mix
Rinse-o-matic®
is ideal. Rinses
clean in seconds!
Item #1410
For more information on these accessories, call 800-4DRINK4 (800-437-4654)
or 440-235-0214. If you live outside the United States or Canada, contact your local
Vita-Mix Distributor or telephone the Vita-Mix International Division at +1.440.782.2450
or email [email protected] for a distributor in your country.
To see the complete line of Vita-Mix products,
VITA-MIX® CORPORATION
Foodservice Division
8615 Usher Road, Cleveland, Ohio 44138-2103 USA
©2006 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or
by any means, electronic or mechanical, including photocopy, recording or any information storage and retrieval system
without the written permission of the Vita-Mix Corporation.
Printed in U.S.A.
XDM034 03/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|